LMV821-Q1 [TI]
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS; 低电压轨到轨输出运算放大器
| 型号： | LMV821-Q1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS |
| 文件： | 总24页 (文件大小：821K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LMV821-Q1 is Obsolete
LMV821-Q1
LMV822-Q1
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
Check for Samples: LMV821-Q1, LMV822-Q1, LMV824-Q1
The LMV82x devices are characterized for operation
from –40°C to 125°C.
1
FEATURES
•
•
•
•
•
Qualified for Automotive Applications
2.5-V, 2.7-V, and 5-V Performance
–40°C to 125°C Operation
LMV821...DBV PACKAGE
(TOP VIEW)
No Crossover Distortion
1
2
3
5
4
IN+
GND/VCC-
IN-
VCC+
Low Supply Current at VCC+ = 5 V
–
–
–
LMV821: 0.3 mA Typ
LMV822: 0.5 mA Typ
LMV824: 1 mA Typ
OUT
•
•
•
Rail-to-Rail Output Swing
LMV822...DGK PACKAGE
(TOP VIEW)
Gain Bandwidth of 5.5 MHz Typ at 5 V
Slew Rate of 1.9 V/µs Typ at 5 V
1OUT
1IN-
VCC+
1
2
3
4
8
7
6
5
2OUT
2IN -
2IN+
DESCRIPTION/ORDERING INFORMATION
1IN+
The LMV821 single, LMV822 dual, and LMV824 quad
devices are low-voltage (2.5 V to 5.5 V), low-power
GND/VCC-
commodity
operational
amplifiers.
Electrical
LMV824...D OR PW PACKAGE
(TOP VIEW)
characteristics are very similar to the LMV3xx
operational amplifiers (low supply current, rail-to-rail
outputs, input common-mode range that includes
ground). However, the LMV82x devices offer a higher
bandwidth (5.5 MHz typical) and faster slew rate
(1.9 V/µs typical).
1OUT
1
2
3
4
5
6
7
14 4OUT
1IN-
1IN+
VCC+
4IN–
13
12
11
10
9
4IN+
GND/VCC-
3IN+
The LMV82x devices are cost-effective solutions for
applications
2IN+
2IN-
requiring
low-voltage/low-power
operation and space-saving considerations. The
LMV821 saves space on printed circuit boards and
enables the design of small portable electronic
devices (cordless and cellular phones, laptops, PDAs,
PCMIA). It also allows the designer to place the
device closer to the signal source to reduce noise
pickup and increase signal integrity.
3IN–
2OUT
3OUT
8
ORDERING INFORMATION(1)
TA
PACKAGE(2)
ORDERABLE PART NUMBER
LMV821QDBVRQ1
LMV822QDGKRQ1
LMV824QDRQ1
TOP-SIDE MARKING(3)
Single
Dual
SOT-23 – DBV
Reel of 3000
Reel of 2500
Reel of 2500
Reel of 2000
RB1_
MSOP/VSSOP – DGK
SOIC – D
R8B
–40°C to 125°C
LMV824Q
MV824Q
Quad
TSSOP – PW
LMV824QPWRQ1
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
(3) DBV: The actual top-side marking has one additional character that designates the wafer fab/assembly site.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2005–2010, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
SYMBOL (EACH AMPLIFIER)
−
IN −
OUT
+
IN +
SIMPLIFIED SCHEMATIC
V
CC
V
BIAS1
V
CC
+
−
V
BIAS2
V
BIAS5
+
−
+
Output
V
CC
V
CC
−
V
BIAS3
+
−
IN−
IN+
V
BIAS4
+
−
2
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
ABSOLUTE MAXIMUM RATINGS(1)
over operating free-air temperature range (unless otherwise noted)
VCC
VID
VI
Supply voltage(2)
Differential input voltage(3)
5.5 V
±VCC
Input voltage range (either input)
Duration of output short circuit (one amplifier) to ground(4)
VCC– to VCC+
At or below TA = 25°C, VCC ≤ 5.5 V
Unlimited
97°C/W
D package
DBV package
DGK package
PW package
206°C/W
172°C/W
113°C/W
150°C
qJA
Package thermal impedance(5) (6)
TJ
Operating virtual-junction temperature
Storage temperature range
Tstg
–65°C to 150°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
(3) Differential voltages are at IN+ with respect to IN−.
(4) Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
(5) Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/qJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
(6) The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS
MIN
2.5
MAX
5
UNIT
V
VCC Supply voltage (single-supply operation)
TA Operating free-air temperature
–40
125
°C
2.5-V ELECTRICAL CHARACTERISTICS
VCC+ = 2.5 V, VCC– = 0 V, VIC = 1 V, VO = 1.25 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX UNIT
25°C
1
2.37
0.13
2.46
0.08
6
VIO
Input offset voltage
mV
6
–40°C to 125°C
25°C
2.28
2.18
High level
Low level
High level
Low level
–40°C to 125°C
25°C
VCC+ = 2.5 V, RL = 600 Ω to 1.25 V
0.22
–40°C to 125°C
25°C
0.32
V
VO
Output swing
2.38
2.28
–40°C to 125°C
25°C
VCC+ = 2.5 V, RL = 2 kΩ to 1.25 V
0.14
0.22
–40°C to 125°C
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
2.7-V ELECTRICAL CHARACTERISTICS
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
25°C
MIN
TYP
MAX
UNIT
1
6
6
VIO
aVIO
IIB
Input offset voltage
mV
–40°C to 125°C
Average temperature coefficient
of input offset voltage
25°C
1
µV/°C
nA
25°C
–40°C to 125°C
25°C
30
90
140
30
Input bias current
Input offset current
0.5
85
85
85
IIO
nA
dB
dB
–40°C to 125°C
25°C
50
70
68
75
70
73
70
CMRR Common-mode rejection ratio
VIC = 0 to 1.7 V
–40°C to 125°C
25°C
Positive supply-voltage
+kSVR
VCC+ = 1.7 V to 4 V, VCC− = –1 V,
VO = 0, VIC = 0
rejection ratio
–40°C to 125°C
25°C
Negative supply-voltage
–kSVR
VCC+ = 1.7 V, VCC− = –1 V to –3.3 V,
VO = 0, VIC = 0
dB
V
rejection ratio
–40°C to 125°C
Common-mode input
voltage range
–0.2
to 1.9
–0.3
to 2
VICR
CMRR ≥ 50 dB
25°C
25°C
–40°C to 125°C
25°C
90
85
85
80
95
90
90
85
2.5
2.4
100
RL = 600 Ω to 1.35 V,
Sourcing
VO = 1.35 V to 2.2 V
90
RL = 600 Ω to 1.35 V,
Sinking
VO = 1.35 V to 0.5 V
–40°C to 125°C
25°C
AV
Large-signal voltage amplification
dB
100
95
RL = 2 kΩ to 1.35 V,
Sourcing
VO = 1.35 V to 2.2 V
–40°C to 125°C
25°C
RL = 2 kΩ to 1.35 V,
Sinking
VO = 1.35 V to 0.5 V
–40°C to 125°C
25°C
2.58
0.13
2.66
0.08
High level
VCC+ = 2.7 V,
–40°C to 125°C
25°C
RL = 600 Ω to 1.35 V
0.2
0.3
Low level
–40°C to 125°C
25°C
VO
Output swing
V
2.6
2.5
High level
VCC+ = 2.7 V,
–40°C to 125°C
25°C
RL = 2 kΩ to 1.35 V
0.12
0.2
Low level
–40°C to 125°C
25°C
VO = 0 V
Sourcing
Sinking
12
12
16
26
IO
Output current
Supply current
mA
mA
VO = 2.7 V
25°C
25°C
0.22
0.3
0.5
0.6
0.8
1
LMV821
–40°C to 125°C
25°C
0.45
0.72
ICC
LMV822 (both amplifiers)
–40°C to 125°C
25°C
LMV824 (all four amplifiers)
–40°C to 125°C
1.2
4
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
2.7-V ELECTRICAL CHARACTERISTICS (continued)
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
Slew rate(1)
GBW Gain bandwidth product
TEST CONDITIONS
TA
MIN
TYP
1.7
5
MAX
UNIT
V/µs
MHz
deg
SR
25°C
25°C
25°C
25°C
25°C
25°C
25°C
(2)
(2)
(2)
Φm
Phase margin
60
Gain margin
8.6
135
45
dB
Amplifier-to-amplifier isolation
Equivalent input noise voltage
Equivalent input noise current
VCC+ = 5 V, RL = 100 kΩ to 2.5 V(3)
f = 1 kHz, VIC = 1 V
f = 1 kHz
dB
Vn
In
nV/√Hz
pA/√Hz
0.18
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
THD
Total harmonic distortion
25°C
0.01
%
(1) Connected as voltage follower with 1-V step input. Value specified is the slower of the positive and negative slew rates.
(2) 40-dB closed-loop dc gain, CL = 22 pF
(3) Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
5-V ELECTRICAL CHARACTERISTICS
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
25°C
MIN
TYP
MAX
UNIT
1
6
6
VIO
aVIO
IIB
Input offset voltage
mV
–40°C to 125°C
Average temperature coefficient
of input offset voltage
25°C
1
µV/°C
nA
25°C
–40°C to 125°C
25°C
40
100
150
30
Input bias current
Input offset current
0.5
90
IIO
nA
dB
dB
–40°C to 125°C
25°C
50
72
70
CMRR Common-mode rejection ratio
VIC = 0 to 4 V
–40°C to 125°C
25°C
75
85
Positive supply-voltage
+kSVR
VCC+ = 1.7 V to 4 V, VCC− = –1 V,
VO = 0, VIC = 0
rejection ratio
–40°C to 125°C
25°C
70
73
85
Negative supply-voltage
–kSVR
VCC+ = 1.7 V, VCC− = –1 V to –3.3 V,
VO = 0, VIC = 0
dB
V
rejection ratio
–40°C to 125°C
70
Common-mode input
voltage range
–0.2
–0.3
to 4.2 to 4.3
VICR
CMRR ≥ 50 dB
25°C
25°C
–40°C to 125°C
25°C
95
90
105
105
105
105
4.84
0.17
4.9
0.1
45
RL = 600 Ω to 2.5 V,
Sourcing
VO = 2.5 V to 4.5 V
95
RL = 600 Ω to 2.5 V,
Sinking
VO = 2.5 V to 0.5 V
–40°C to 125°C
25°C
90
AV
Large-signal voltage amplification
dB
95
RL = 2 kΩ to 2.5 V,
Sourcing
VO = 2.5 V to 4.5 V
–40°C to 125°C
25°C
90
95
RL = 2 kΩ to 2.5 V,
Sinking
VO = 2.5 V to 0.5 V
–40°C to 125°C
25°C
90
4.75
4.6
High level
VCC+ = 5 V,
–40°C to 125°C
25°C
RL = 600 Ω to 2.5 V
0.25
0.3
Low level
–40°C to 125°C
25°C
VO
Output swing
V
4.85
4.8
High level
VCC+ = 5 V,
–40°C to 125°C
25°C
RL = 2 kΩ to 2.5 V
0.15
0.2
Low level
–40°C to 125°C
25°C
20
15
20
15
VO = 0 V
Sourcing
Sinking
–40°C to 125°C
25°C
IO
Output current
Supply current
mA
mA
40
VO = 5 V
–40°C to 125°C
25°C
0.3
0.5
1
0.4
0.6
0.7
0.9
1.3
1.5
LMV821
–40°C to 125°C
25°C
ICC
LMV822 (both amplifiers)
–40°C to 125°C
25°C
LMV824 (all four amplifiers)
–40°C to 125°C
6
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
5-V ELECTRICAL CHARACTERISTICS (continued)
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
Slew rate
GBW Gain bandwidth product
TEST CONDITIONS
VCC+ = 5 V(1)
(2)
(2)
(2)
TA
MIN
TYP
1.9
5.5
64.2
8.7
135
42
MAX
UNIT
V/µs
MHz
deg
SR
25°C
25°C
25°C
25°C
25°C
25°C
25°C
1.4
Φm
Phase margin
Gain margin
dB
Amplifier-to-amplifier isolation
Equivalent input noise voltage
Equivalent input noise current
VCC+ = 5 V, RL = 100 kΩ to 2.5 V(3)
f = 1 kHz, VIC = 1 V
f = 1 kHz
dB
Vn
In
nV/√Hz
pA/√Hz
0.2
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
THD
Total harmonic distortion
25°C
0.01
%
(1) Connected as voltage follower with 3-V step input. Value specified is the slower of the positive and negative slew rates.
(2) 40-dB closed-loop dc gain, CL = 22 pF
(3) Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
SUPPLY CURRENT
INPUT CURRENT
vs
vs
SUPPLY VOLTAGE
TEMPERATURE
1200
1000
800
−30
All Channels
V
V
= 5 V
CC+
T
= 855C
= 255C
A
= V
/2
in
CC+
−40
−50
−60
−70
T
A
600
400
200
T
A
= −405C
0
−40
−20
0
20
40
60
80
100
0
1
2
3
4
5
6
T
A
− Temperature − °C
V
CC+
− Supply Voltage − V
Figure 1.
Figure 2.
SOURCING CURRENT
vs
SOURCING CURRENT
vs
OUTPUT VOLTAGE
OUTPUT VOLTAGE
100
100
V
CC+
= 2.7 V
V
CC+
= 5 V
10
1
10
1
0.1
0.1
0.01
0.01
0.001
0.01
0.1
1
10
0.001
0.01
0.1
1
10
Output Voltage Referenced to V+ − (V)
Output Voltage Referenced to V+ − (V)
Figure 3.
Figure 4.
8
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
SINKING CURRENT
vs
SINKING CURRENT
vs
OUTPUT VOLTAGE
OUTPUT VOLTAGE
100
100
10
V
CC+
= 2.7 V
V
CC+
= 5 V
10
1
1
0.1
0.01
0.1
0.01
0.1
0.01
1
10
0.1
0.01
1
10
Output Voltage Referenced to GND − V
Output Voltage Referenced to GND − V
Figure 5.
Figure 6.
OUTPUT VOLTAGE SWING
vs
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
50
40
80
70
60
R
L
= 10 kΩ to Mid Rail
R
L
= 2 kΩ to Mid Rail
Negative Swing
Positive Swing
50
40
30
30
20
Negative Swing
Positive Swing
20
10
0
10
0
2.6
3
3.4
3.8
4.2
4.6
5
2.6
3
3.4
3.8
4.2
4.6
5
V
CC+
− Supply Voltage − V
V
CC+
− Supply Voltage − V
Figure 7.
Figure 8.
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
OUTPUT VOLTAGE SWING
vs
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
LOAD RESISTANCE
160
150
140
130
120
160
140
R = 600 Ω to Mid Rail
L
R
= 5 kΩ to Mid Rail
= 5 V
lL
V
CC+
Negative Swing
Positive Swing
120
100
80
60
40
20
110
100
90
80
70
0
60
2.6
100
1000
10k
100k
3
3.4
3.8
4.2
4.6
5
Resistive Load − Ω
V
CC+
− Supply Voltage − V
Figure 9.
Figure 10.
CROSSTALK REJECTION
+PSRR
vs
vs
FREQUENCY
FREQUENCY
100
160
V
CC
= +2.5 V
+
90
150
80
70
60
50
40
30
20
140
130
V
CC
= +1.35 V
+
120
110
100
90
V
= ±2.5 V
CC+
V = 3 V
I
PP
= 5 kΩ
= 1
R
A
V
L
10
0
1k
10k
100k
1M
100
100
1k
Frequency − Hz
Figure 11.
10k
100k
Frequency − Hz
Figure 12.
10
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
–PSRR
vs
FREQUENCY
100
90
V
CC
= +2.5 V
+
80
70
60
V
CC
= +1.35 V
+
50
40
30
20
10
0
100
1k
10k
100k
1M
Frequency − Hz
Figure 13.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
70
60
140
120
Phase
100
80
50
40
30
20
10
60
40
Gain
20
0
V
CC+
= 2.7 V
600 Ω
2 kΩ
−20
0
−10
−20
−40
−60
100 kΩ
1k
10k
100k
1M
10M
Frequency − Hz
Figure 14.
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
140
120
100
80
80
70
60
50
40
Phase
60
40
30
20
10
20
Gain
0
−20
V
CC+
= 5 V
600 Ω
2 kΩ
0
−10
−20
−40
−60
100 kΩ
1M
1k
10k
10M
100k
Frequency − Hz
Figure 15.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
70
100
80
60
Phase
60
50
40
30
20
10
40
20
0
−20
−40
−60
Gain
V
= 2.7 V
CC+
R = 10 kΩ
L
0
−10
−20
22 pF
100 pF
200 pF
−80
−100
1k
10k
100k
1M
10M
Frequency − Hz
Figure 16.
12
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
www.ti.com
SLOS461F –MARCH 2005–REVISED JULY 2010
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
80
70
60
50
40
Phase
60
40
20
0
30
20
10
0
Gain
−20
−40
V
= 5 V
CC+
R = 10 kΩ
L
−60
22 pF
100 pF
200 pF
−80
−10
−20
−100
10M
1k
10k
100k
1M
Frequency − Hz
Figure 17.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
140
120
100
80
70
60
50
Phase
80
40
30
20
60
40
20
Gain
V
= 2.7 V
CC+
10
0
0
R = 600 Ω
L
−20
−40
22 pF
100 pF
200 pF
−10
−20
−60
1k
10k
100k
1M
10M
Frequency − Hz
Figure 18.
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV821-Q1 is Obsolete
LMV824-Q1
SLOS461F –MARCH 2005–REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
140
120
80
70
Phase
60
100
80
50
40
60
40
30
20
10
Gain
20
0
V
CC+
= 5 V
R = 600 Ω
L
−20
0
−10
−20
22 pF
100 pF
200 pF
−40
−60
1k
10k
100k
1M
10M
Frequency − Hz
Figure 19.
14
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
LMV821QDBVRQ1
LMV822QDGKRQ1
ACTIVE
ACTIVE
SOT-23
VSSOP
DBV
DGK
5
8
TBD
Call TI
Call TI
2500
2500
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
LMV824QDRQ1
ACTIVE
ACTIVE
SOIC
D
14
14
Green (RoHS
& no Sb/Br)
LMV824QPWRQ1
TSSOP
PW
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMV821-Q1, LMV822-Q1, LMV824-Q1 :
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
Catalog: LMV821, LMV822, LMV824
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMV824QPWRQ1
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
TSSOP PW 14
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
LMV824QPWRQ1
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明