LMV832MME/NOPB [TI]
Dual, 5.5-V, 3.3-MHz, low noise (12-nV/√Hz) operational amplifier | DGK | 8 | -40 to 125;型号: | LMV832MME/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | Dual, 5.5-V, 3.3-MHz, low noise (12-nV/√Hz) operational amplifier | DGK | 8 | -40 to 125 放大器 运算放大器 放大器电路 |
文件: | 总27页 (文件大小:1391K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
LMV831 Single/ LMV832 Dual/ LMV834 Quad 3.3 MHz Low Power CMOS, EMI Hardened
Operational Amplifiers
Check for Samples: LMV831, LMV832, LMV834
1
FEATURES
DESCRIPTION
TI’s LMV831, LMV832, and LMV834 are CMOS input,
low power op amp IC's, providing a low input bias
current, a wide temperature range of −40°C to 125°C
and exceptional performance making them robust
2
•
Unless Otherwise Noted, Typical Values at TA=
25°C, V+ = 3.3V
•
•
•
•
•
•
•
•
•
•
•
Supply Voltage 2.7V to 5.5V
Supply Current (per Channel) 240 µA
Input Offset Voltage 1 mV Max
Input Bias Current 0.1 pA
GBW 3.3 MHz
general
purpose
parts.
Additionally,
the
LMV831/LMV832/LMV834 are EMI hardened to
minimize any interference so they are ideal for EMI
sensitive applications.
The unity gain stable LMV831/LMV832/LMV834
feature 3.3 MHz of bandwidth while consuming only
0.24 mA of current per channel. These parts also
maintain stability for capacitive loads as large as 200
pF. The LMV831/LMV832/LMV834 provide superior
performance and economy in terms of power and
space usage.
EMIRR at 1.8 GHz 120 dB
Input Noise Voltage at 1 kHz 12 nV/√Hz
Slew Rate 2 V/µs
Output Voltage Swing Rail-to-Rail
Output Current Drive 30 mA
Operating Ambient Temperature Range −40°C
to 125°C
This family of parts has a maximum input offset
voltage of 1 mV, a rail-to-rail output stage and an
input common-mode voltage range that includes
ground. Over an operating range from 2.7V to 5.5V
the LMV831/LMV832/LMV834 provide a PSRR of 93
dB, and a CMRR of 91 dB. The LMV831 is offered in
the space saving 5-Pin SC70 package, the LMV832
in the 8-Pin VSSOP and the LMV834 is offered in the
14-Pin TSSOP package.
APPLICATIONS
•
•
•
Photodiode Preamp
Piezoelectric Sensors
Portable/Battery-Powered Electronic
Equipment
•
•
Filters/Buffers
PDAs/Phone Accessories
Typical Application
R1
+
V
NO RF RELATED
DISTURBANCES
R2
PRESSURE
SENSOR
-
-
-
+
+
ADC
+
EMI HARDENED
EMI HARDENED
INTERFERING
RF SOURCES
Figure 1. EMI Hardened Sensor Application
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Human Body Model
Charge-Device Model
Machine Model
2 kV
ESD Tolerance(3)
1 kV
200V
VIN Differential
Supply Voltage (VS = V+ – V−)
± Supply Voltage
6V
V++0.4V,
Voltage at Input/Output Pins
V− −0.4V
Storage Temperature Range
Junction Temperature(4)
Soldering Information
−65°C to 150°C
150°C
Infrared or Convection (20 sec)
260°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
(4) The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.
Operating Ratings(1)
Temperature Range(2)
Supply Voltage (VS = V+ – V−)
−40°C to 125°C
2.7V to 5.5V
302°C/W
5-Pin SC70
(2)
Package Thermal Resistance (θJA
)
8-Pin VSSOP
14-Pin TSSOP
217°C/W
135°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
(2) The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.
3.3V Electrical Characteristics(1)
Unless otherwise specified, all limits are specified for at TA = 25°C, V+ = 3.3V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
VOS
TCVOS
Parameter
Conditions
Min
Typ
Max
Units
(2)
(3)
(2)
Input Offset Voltage(4)
±0.25
±0.5
±0.5
±1.00
±1.23
mV
Input Offset Voltage Temperature
Drift(4)(5)
LMV831,
LMV832
±1.5
μV/°C
LMV834
±1.7
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ > TA.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using
statistical quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) The typical value is calculated by applying absolute value transform to the distribution, then taking the statistical average of the resulting
distribution.
(5) This parameter is specified by design and/or characterization and is not tested in production.
2
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
3.3V Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits are specified for at TA = 25°C, V+ = 3.3V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
(2)
(3)
(2)
IB
Input Bias Current(5)
0.1
10
500
pA
pA
dB
IOS
Input Offset Current
Common-Mode Rejection Ratio(4)
1
CMRR
0.2V ≤ VCM ≤ V+ - 1.2V
76
75
91
PSRR
Power Supply Rejection Ratio(4)
EMI Rejection Ratio, IN+ and IN-(6)
2.7V ≤ V+ ≤ 5.5V,
VOUT = 1V
76
75
93
80
dB
EMIRR
VRF_PEAK=100 mVP (−20 dBP),
f = 400 MHz
VRF_PEAK=100 mVP (−20 dBP),
90
f = 900 MHz
dB
V
VRF_PEAK=100 mVP (−20 dBP),
f = 1800 MHz
110
120
VRF_PEAK=100 mVP (−20 dBP),
f = 2400 MHz
CMVR
AVOL
Input Common-Mode Voltage Range
Large Signal Voltage Gain(7)
CMRR ≥ 65 dB
−0.1
2.1
RL = 2 kΩ,
VOUT = 0.15V to 1.65V, LMV832
VOUT = 3.15V to 1.65V
LMV831,
102
102
121
121
126
123
29
LMV834
102
102
dB
RL = 10 kΩ,
VOUT = 0.1V to 1.65V, LMV832
VOUT = 3.2V to 1.65V
LMV831,
104
104
LMV834
104
103
VOUT
Output Voltage Swing High
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
LMV831,
LMV832
36
43
LMV834
31
38
44
LMV831,
LMV832
6
8
9
mV from
either rail
LMV834
7
9
10
Output Voltage Swing Low
Output Short Circuit Current
R = 2 kΩ to V+/2
25
34
43
RL = 10 kΩ to V+/2
5
8
10
IOUT
Sourcing, VOUT = VCM
VIN = 100 mV
,
LMV831,
LMV832
27
22
28
LMV834
24
19
28
mA
Sinking, VOUT = VCM
,
27
32
VIN = −100 mV
21
IS
Supply Current
LMV831
LMV832
LMV834
0.24
0.46
0.90
2
0.27
0.30
0.51
0.58
mA
1.00
1.16
SR
Slew Rate(8)
AV = +1, VOUT = 1 VPP
,
V/μs
10% to 90%
(6) The EMI Rejection Ratio is defined as EMIRR = 20log ( VRF_PEAK/ΔVOS).
(7) The specified limits represent the lower of the measured values for each output range condition.
(8) Number specified is the slower of positive and negative slew rates.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
3.3V Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits are specified for at TA = 25°C, V+ = 3.3V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
(2)
(3)
(2)
GBW
Gain Bandwidth Product
Phase Margin
3.3
65
MHz
deg
Φm
en
Input Referred Voltage Noise Density f = 1 kHz
f = 10 kHz
12
nV/√Hz
10
in
Input Referred Current Noise Density
Closed Loop Output Impedance
Common-mode Input Capacitance
Differential-mode Input Capacitance
Total Harmonic Distortion + Noise
f = 1 kHz
f = 2 MHz
0.005
500
15
pA/√Hz
ROUT
CIN
Ω
pF
%
20
THD+N
f = 1 kHz, AV = 1, BW ≥ 500 kHz
0.02
5V Electrical Characteristics(1)
Unless otherwise specified, all limits are specified for at TA = 25°C, V+ = 5V, V− = 0V, VCM = V+/2, and RL = 10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
VOS
TCVOS
Parameter
Conditions
Min
Typ
Max
Units
(2)
(3)
(2)
Input Offset Voltage(4)
±0.25
±0.5
±1.00
±1.23
mV
Input Offset Voltage Temperature
Drift(4)(5)
LMV831,
LMV832
±1.5
±1.7
μV/°C
LMV834
±0.5
0.1
IB
Input Bias Current(5)
10
500
pA
pA
dB
IOS
Input Offset Current
Common-Mode Rejection Ratio(4)
1
CMRR
0V ≤ VCM ≤ V+ −1.2V
77
77
93
PSRR
Power Supply Rejection Ratio(4)
EMI Rejection Ratio, IN+ and IN-(6)
2.7V ≤ V+ ≤ 5.5V,
VOUT = 1V
76
75
93
80
dB
EMIRR
VRF_PEAK=100 mVP (−20 dBP),
f = 400 MHz
VRF_PEAK=100 mVP (−20 dBP),
90
f = 900 MHz
dB
V
VRF_PEAK=100 mVP (−20 dBP),
f = 1800 MHz
110
120
VRF_PEAK=100 mVP (−20 dBP),
f = 2400 MHz
CMVR
Input Common-Mode Voltage Range
CMRR ≥ 65 dB
–0.1
3.8
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ > TA.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using
statistical quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) The typical value is calculated by applying absolute value transform to the distribution, then taking the statistical average of the resulting
distribution.
(5) This parameter is specified by design and/or characterization and is not tested in production.
(6) The EMI Rejection Ratio is defined as EMIRR = 20log ( VRF_PEAK/ΔVOS).
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
5V Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits are specified for at TA = 25°C, V+ = 5V, V− = 0V, VCM = V+/2, and RL = 10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
(2)
(3)
(2)
AVOL
Large Signal Voltage Gain(7)
RL = 2 kΩ,
VOUT = 0.15V to 2.5V, LMV832
VOUT = 4.85V to 2.5V
LMV831,
107
106
127
127
130
127
32
LMV834
104
104
dB
RL = 10 kΩ,
VOUT = 0.1V to 2.5V,
VOUT = 4.9V to 2.5V
LMV831,
LMV832
107
107
LMV834
105
104
VOUT
Output Voltage Swing High
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
LMV831,
LMV832
42
49
LMV834
35
45
52
LMV831,
LMV832
6
9
10
mV from
either rail
LMV834
7
10
11
Output Voltage Swing Low
Output Short Circuit Current
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
27
43
52
6
10
12
IOUT
Sourcing VOUT = VCM
VIN = 100 mV
LMV831,
LMV832
59
49
66
LMV834
57
45
63
mA
Sinking VOUT = VCM
VIN = −100 mV
LMV831,
LMV832
50
41
64
LMV834
LMV831
LMV832
LMV834
53
41
63
IS
Supply Current
0.25
0.47
0.92
2
0.27
0.31
0.52
0.60
mA
1.02
1.18
SR
Slew Rate(8)
AV = +1, VOUT = 2VPP
10% to 90%
,
V/μs
GBW
Φm
Gain Bandwidth Product
Phase Margin
3.3
65
MHz
deg
en
Input Referred Voltage Noise
f = 1 kHz
f = 10 kHz
f = 1 kHz
f = 2 MHz
12
nV/√Hz
10
in
Input Referred Current Noise
0.005
500
14
pA/√Hz
ROUT
CIN
Closed Loop Output Impedance
Common-mode Input Capacitance
Differential-mode Input Capacitance
Total Harmonic Distortion + Noise
Ω
pF
%
20
THD+N
f = 1 kHz, AV = 1, BW ≥ 500 kHz
0.02
(7) The specified limits represent the lower of the measured values for each output range condition.
(8) Number specified is the slower of positive and negative slew rates.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
Connection Diagram
Figure 2. 5-Pin SC70
Top View
Figure 3. 8-Pin VSSOP
Top View
Figure 4. 14-Pin TSSOP
Top View
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
Typical Performance Characteristics
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
VOS vs. VCM at V+ = 3.3V
VOS vs. VCM at V+ = 5.0V
125°C
85°C
125°C
85°C
0.3
0.2
0.1
0
0.3
0.2
0.1
0
25°C
25°C
-0.1
-0.2
-0.3
-0.1
-0.2
-0.3
-40°C
-40°C
+
+
V
= 5.0V
0.5
V
= 3.3V
-0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
(V)
-0.5
1.5
2.5
CM
3.5
4.5
5.5
V
(V)
V
CM
Figure 5.
Figure 6.
VOS vs. Supply Voltage
VOS vs. Temperature
125°C
85°C
0.3
0.2
0.1
0
3.3V
200
150
100
50
5.0V
25°C
0
-50
-0.1
-0.2
-0.3
-100
-150
-200
-40°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
(V)
-50 -25
0
25
50
75 100 125
TEMPERATURE (°C)
V
SUPPLY
Figure 7.
VOS vs. VOUT
Figure 8.
Input Bias Current vs. VCM at 25°C
= 25°C
5
4
T
+
A
V
= 5.0V, R = 2k
L
6
4
3
2
5V
2
1
0
0
-1
-2
-3
-4
-5
-2
-4
-6
3.3V
0
1
2
3
4
5
-1
0
1
2
3
4
5
6
V
(V)
OUT
V
(V)
CM
Figure 9.
Figure 10.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
Input Bias Current vs. VCM at 85°C
Input Bias Current vs. VCM at 125°C
= 125°C
50
500
400
300
200
100
0
T
A
= 85°C
T
A
40
30
20
10
5.0V
0
5.0V
-10
-20
-30
-40
-50
-100
-200
-300
-400
-500
3.3V
3.3V
-1
0
1
2
3
4
5
6
-1
0
1
2
3
4
5
6
V
(V)
V
(V)
CM
CM
Figure 11.
Figure 12.
Supply Current vs. Supply Voltage Single LMV831
Supply Current vs. Supply Voltage Dual LMV832
0.4
0.7
85°C
125°C
125°C
85°C
0.6
0.5
0.4
0.3
0.3
0.2
0.1
25°C
25°C
-40°C
-40°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
Figure 13.
Figure 14.
Supply Current vs. Supply Voltage Quad LMV834
Supply Current vs. Temperature Single LMV831
0.4
1.4
1.2
1.0
0.8
0.6
0.4
85°C
125°C
0.3
0.2
0.1
5.0V
25°C
3.3V
-40°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
-50 -25
0
25
50
75 100 125
TEMPERATURE (°C)
Figure 15.
Figure 16.
8
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
Supply Current vs. Temperature Dual LMV832
Supply Current vs. Temperature Quad LMV834
0.7
0.6
1.4
1.2
1.0
0.8
0.6
0.4
5.0V
5.0V
0.5
3.3V
0.4
3.3V
0.3
-50 -25
0
25
50
75 100 125
-50 -25
0
25
50
75 100 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 17.
Figure 18.
Sinking Current vs. Supply Voltage
Sourcing Current vs. Supply Voltage
100
90
80
70
60
50
40
30
20
10
100
90
80
70
60
50
40
30
20
10
25°C
25°C
-40°C
-40°C
125°C
85°C
125°C
85°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
Figure 19.
Figure 20.
Output Swing High vs. Supply Voltage RL = 2 kΩ
= 2k
Output Swing High vs. Supply Voltage RL = 10 kΩ
= 10k
R
L
R
L
60
50
40
30
20
10
12
10
8
125°C
125°C
85°C
85°C
6
4
2
25°C
-40°C
25°C
0
-40°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
Figure 21.
Figure 22.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
Output Swing Low vs. Supply Voltage RL = 2 kΩ
Output Swing Low vs. Supply Voltage RL = 10 kΩ
R
L
= 10k
R
L
= 2k
60
50
40
30
20
10
125°C
12
10
8
125°C
85°C
85°C
6
4
25°C
25°C
2
-40°C
0
-40°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
Figure 23.
Figure 24.
Output Voltage Swing vs. Load Current at V+ = 3.3V
Output Voltage Swing vs. Load Current at V+ = 5.0V
SINK
SINK
125°C
125°C
2.0
1.6
1.2
0.8
0.4
2.0
1.6
1.2
0.8
0.4
+
+
0
0
-40°C
V = 5.0V
V
= 3.3V
-40°C
-0.4
-0.8
-1.2
-1.6
-2.0
-0.4
-0.8
-1.2
-1.6
-2.0
125°C
125°C
SOURCE
SOURCE
10 20 30 40 50 60 70 80
(mA)
0
5
10 15 20 25 30 35 40
(mA)
0
I
I
LOAD
LOAD
Figure 25.
Figure 26.
Open Loop Frequency Response vs. Temperature
Open Loop Frequency Response vs. Load Conditions
60
50
40
30
20
10
0
100
80
60
40
20
0
60
50
40
30
20
10
0
100
80
60
40
20
0
25°C, 85°C, 125°C
PHASE
20 pF 5 pF
100 pF
50 pF
GAIN
25°C
85°C
125°C
C
= 5 pF
L
5 pF
20 pF
50 pF
100 pF
-40°C
100 pF
1M
-20
10M
-20
10M
10k
100k
1M
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 27.
Figure 28.
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
Phase Margin vs. Capacitive Load
PSRR vs. Frequency
120
100
80
60
40
20
0
70
60
50
3.3V
5.0V
5.0V
40
30
20
10
0
-PSRR
3.3V
5.0V
3.3V
+PSRR
1
10
100
(pF)
1000
100
1k
10k
100k
1M
10M
C
LOAD
FREQUENCY (Hz)
Figure 29.
CMRR vs. Frequency
Figure 30.
Channel Separation vs. Frequency
100
80
60
40
20
160
140
120
100
80
AC CMRR
DC
CMRR
V+ = 3.3V, 5.0V
V+ = 3.3V, 5.0V
60
1k
100
1k
10k
100k
1M
10M
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 31.
Figure 32.
Large Signal Step Response with Gain = 1
Large Signal Step Response with Gain = 10
f = 100 kHz
f = 100 kHz
A
= +10
A
V
= +1
V
V
= 500 mV
V
= 100 mV
IN
PP
IN
PP
1 µs/DIV
1 us/DIV
Figure 33.
Figure 34.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
Small Signal Step Response with Gain = 1
Small Signal Step Response with Gain = 10
f = 100 kHz
f = 100 kHz
A
V
= +10
V
A
= +1
V
= 10 mV
IN
PP
V
= 100 mV
IN
PP
1 µs/DIV
1 µs/DIV
Figure 35.
Figure 36.
Slew Rate vs. Supply Voltage
Input Voltage Noise vs. Frequency
100
10
1
2.0
1.9
1.8
1.7
1.6
1.5
FALLING EDGE
RISING EDGE
A
= +1
V
+
C
= 5 pF
L
V
= 3.3V, 5.0V
100
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
10
1k
10k
100k
FREQUENCY (Hz)
Figure 37.
Figure 38.
THD+N vs. Frequency
THD+N vs. Amplitude
V+ = 5.0V
V+ = 3.3V
A
= 10x
BW = >500 kHz
V
0.1
0.01
10
1
A
V
= 10x
+
V
= 3.3V
V
IN
= 300 mV
PP
A
= 1x
V
0.1
V
IN
= 480 mV
PP
0.001
0.0001
V
= 2.3 V
IN
PP
0.01
0.001
A
V
= 1x
V
= 3.8 V
PP
IN
+
V
= 5.0V
f = 1 kHz
BW = >500 kHz
10
100
1k
10k
1m 10m
100m
(V
1
10
FREQUENCY (Hz)
V
)
OUT PP
Figure 39.
Figure 40.
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
At TA = 25°C, RL = 10 kΩ, V+ = 3.3V, V− = 0V, Unless otherwise specified.
ROUT vs. Frequency
EMIRR IN+ vs. Power at 400 MHz
1k
A
= 100x
V
100
10
140
130
120
110
100
90
80
70
60
1
50
A
= 10x
40
V
30
20
0.1
0.01
A
V
= 1x
f
= 400 MHz
-30
RF
100
1k
10k
100k
1M
10M
-40
-20
-10
0
10
RF INPUT PEAK VOLTAGE (dBVp)
FREQUENCY (Hz)
Figure 41.
Figure 42.
EMIRR IN+ vs. Power at 900 MHz
EMIRR IN+ vs. Power at 1800 MHz
140
130
120
110
100
90
140
130
120
110
100
90
80
80
70
70
60
60
50
50
40
40
30
30
20
20
f
= 1800 MHz
f
= 900 MHz
RF
RF
-40
-30
-20
-10
0
10
-40
-30
-20
-10
0
10
RF INPUT PEAK VOLTAGE (dBVp)
RF INPUT PEAK VOLTAGE (dBVp)
Figure 43.
Figure 44.
EMIRR IN+ vs. Power at 2400 MHz
EMIRR IN+ vs. Frequency
140
140
130
120
110
100
90
130
120
110
100
90
80
80
70
70
60
60
50
50
40
40
30
30
20
20
+
V
V
= 3.3V, 5.0V
= -20 dBVp
f
= 2400 MHz
RF
PEAK
-40
-30
-20
-10
0
10
10
100
1000
10000
FREQUENCY (MHz)
RF INPUT PEAK VOLTAGE (dBVp)
Figure 45.
Figure 46.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
APPLICATION INFORMATION
INTRODUCTION
The LMV831, LMV832 and LMV834 are operational amplifiers with excellent specifications, such as low offset,
low noise and a rail-to-rail output. These specifications make the LMV831, LMV832 and LMV834 great choices
for medical and instrumentation applications such as diagnosis equipment. The low supply current is perfectly
suited for battery powered equipment. The small packages, SC70 package for the LMV831, the TSSOP package
for the dual LMV832 and the TSSOP package for the quad LMV834, make these parts a perfect choice for
portable electronics. Additionally, the EMI hardening makes the LMV831, LMV832 or LMV834 a must for almost
all op amp applications. Most applications are exposed to Radio Frequency (RF) signals such as the signals
transmitted by mobile phones or wireless computer peripherals. The LMV831, LMV832 and LMV834 will
effectively reduce disturbances caused by RF signals to a level that will be hardly noticeable. This again reduces
the need for additional filtering and shielding. Using this EMI resistant series of op amps will thus reduce the
number of components and space needed for applications that are affected by EMI, and will help applications,
not yet identified as possible EMI sensitive, to be more robust for EMI.
INPUT CHARACTERISTICS
The input common mode voltage range of the LMV831, LMV832 and LMV834 includes ground, and can even
sense well below ground. The CMRR level does not degrade for input levels up to 1.2V below the supply voltage.
For a supply voltage of 5V, the maximum voltage that should be applied to the input for best CMRR performance
is thus 3.8V.
When not configured as unity gain, this input limitation will usually not degrade the effective signal range. The
output is rail-to-rail and therefore will introduce no limitations to the signal range.
The typical offset is only 0.25 mV, and the TCVOS is 0.5 μV/°C, specifications close to precision op amps.
CMRR MEASUREMENT
The CMRR measurement results may need some clarification. This is because different setups are used to
measure the AC CMRR and the DC CMRR.
The DC CMRR is derived from ΔVOS versus ΔVCM. This value is stated in the tables, and is tested during
production testing. The AC CMRR is measured with the test circuit shown in Figure 47.
R2
1 kW
V+
BUFFER
V+
R1
1 kW
-
V
-
IN
Buffer
V
OUT
LMV83x
+
+
R11
1 kW
V-
BUFFER
V-
R12
995W
P1
10W
Figure 47. AC CMRR Measurement Setup
The configuration is largely the usually applied balanced configuration. With potentiometer P1, the balance can
be tuned to compensate for the DC offset in the DUT. The main difference is the addition of the buffer. This
buffer prevents the open-loop output impedance of the DUT from affecting the balance of the feedback network.
Now the closed-loop output impedance of the buffer is a part of the balance. As the closed-loop output
impedance is much lower, and by careful selection of the buffer also has a larger bandwidth, the total effect is
that the CMRR of the DUT can be measured much more accurately. The differences are apparent in the larger
measured bandwidth of the AC CMRR.
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
One artifact from this test circuit is that the low frequency CMRR results appear higher than expected. This is
because in the AC CMRR test circuit the potentiometer is used to compensate for the DC mismatches. So,
mainly AC mismatch is all that remains. Therefore, the obtained DC CMRR from this AC CMRR test circuit tends
to be higher than the actual DC CMRR based on DC measurements.
The CMRR curve in Figure 48 shows a combination of the AC CMRR and the DC CMRR.
100
AC CMRR
80
DC
CMRR
60
40
V+ = 3.3V, 5.0V
20
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 48. CMRR Curve
OUTPUT CHARACTERISTICS
As already mentioned the output is rail-to-rail. When loading the output with a 10 kΩ resistor the maximum swing
of the output is typically 6 mV from the positive and negative rail.
The output of the LMV831/LMV832/LMV834 can drive currents up to 30 mA at 3.3V and even up to 65 mA at 5V
The LMV831/LMV832/LMV834 can be connected as non-inverting unity-gain amplifiers. This configuration is the
most sensitive to capacitive loading. The combination of a capacitive load placed at the output of an amplifier
along with the amplifier’s output impedance creates a phase lag, which reduces the phase margin of the
amplifier. If the phase margin is significantly reduced, the response will be under damped which causes peaking
in the transfer and, when there is too much peaking, the op amp might start oscillating. The
LMV831/LMV832/LMV834 can directly drive capacitive loads up to 200 pF without any stability issues. In order to
drive heavier capacitive loads, an isolation resistor, RISO, should be used, as shown in Figure 49. By using this
isolation resistor, the capacitive load is isolated from the amplifier’s output, and hence, the pole caused by CL is
no longer in the feedback loop. The larger the value of RISO, the more stable the amplifier will be. If the value of
RISO is sufficiently large, the feedback loop will be stable, independent of the value of CL. However, larger values
of RISO result in reduced output swing and reduced output current drive.
R
ISO
-
V
OUT
V
+
IN
C
L
Figure 49. Isolating Capacitive Load
A resistor value of around 150Ω would be sufficient. As an example some values are given in the following table,
for 5V.
CLOAD
300 pF
400 pF
500 pF
RISO
165Ω
175Ω
185Ω
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
EMIRR
With the increase of RF transmitting devices in the world, the electromagnetic interference (EMI) between those
devices and other equipment becomes a bigger challenge. The LMV831, LMV832 and LMV834 are EMI
hardened op amps which are specifically designed to overcome electromagnetic interference. Along with EMI
hardened op amps, the EMIRR parameter is introduced to unambiguously specify the EMI performance of an op
amp. This section presents an overview of EMIRR. A detailed description on this specification for EMI hardened
op amps can be found in Application Note AN-1698(SNOA497).
The dimensions of an op amp IC are relatively small compared to the wavelength of the disturbing RF signals. As
a result the op amp itself will hardly receive any disturbances. The RF signals interfering with the op amp are
dominantly received by the PCB and wiring connected to the op amp. As a result the RF signals on the pins of
the op amp can be represented by voltages and currents. This representation significantly simplifies the
unambiguous measurement and specification of the EMI performance of an op amp.
RF signals interfere with op amps via the non-linearity of the op amp circuitry. This non-linearity results in the
detection of the so called out-of-band signals. The obtained effect is that the amplitude modulation of the out-of-
band signal is downconverted into the base band. This base band can easily overlap with the band of the op
amp circuit. As an example Figure 50 depicts a typical output signal of a unity-gain connected op amp in the
presence of an interfering RF signal. Clearly the output voltage varies in the rhythm of the on-off keying of the RF
carrier.
RF
NO RF
RF SIGNAL
V
+ V
DETECTED
OS
V
OUT OPAMP
(A = 1)
V
V
OS
Figure 50. Offset voltage variation due to an interfering RF signal
EMIRR DEFINITION
To identify EMI hardened op amps, a parameter is needed that quantitatively describes the EMI performance of
op amps. A quantitative measure enables the comparison and the ranking of op amps on their EMI robustness.
Therefore the EMI Rejection Ratio (EMIRR) is introduced. This parameter describes the resulting input-referred
offset voltage shift of an op amp as a result of an applied RF carrier (interference) with a certain frequency and
level. The definition of EMIRR is given by:
≈
∆
∆
«
’
÷
÷
◊
VRF_PEAK
EMIRRV
RF_PEAK = 20 log
DVOS
In which
•
•
VRF_PEAK is the amplitude of the applied un-modulated RF signal (V)
ΔVOS is the resulting input-referred offset voltage shift (V)
(1)
The offset voltage depends quadratically on the applied RF level, and therefore, the RF level at which the EMIRR
is determined should be specified. The standard level for the RF signal is 100 mVP. Application Note AN-
1698(SNOA497) addresses the conversion of an EMIRR measured for an other signal level than 100 mVP. The
interpretation of the EMIRR parameter is straightforward. When two op amps have an EMIRR which differ by 20
dB, the resulting error signals when used in identical configurations, differ by 20 dB as well. So, the higher the
EMIRR, the more robust the op amp.
Coupling an RF Signal to the IN+ Pin
Each of the op amp pins can be tested separately on EMIRR. In this section the measurements on the IN+ pin
(which, based on symmetry considerations, also apply to the IN- pin) are discussed. In Application Note AN-
1698(SNOA497) the other pins of the op amp are treated as well. For testing the IN+ pin the op amp is
connected in the unity gain configuration. Applying the RF signal is straightforward as it can be connected
directly to the IN+ pin. As a result the RF signal path has a minimum of components that might affect the RF
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
signal level at the pin. The circuit diagram is shown in Figure 51. The PCB trace from RFIN to the IN+ pin should
be a 50Ω stripline in order to match the RF impedance of the cabling and the RF generator. On the PCB a 50Ω
termination is used. This 50Ω resistor is also used to set the bias level of the IN+ pin to ground level. For
determining the EMIRR, two measurements are needed: one is measuring the DC output level when the RF
signal is off; and the other is measuring the DC output level when the RF signal is switched on. The difference of
the two DC levels is the output voltage shift as a result of the RF signal. As the op amp is in the unity gain
configuration, the input referred offset voltage shift corresponds one-to-one to the measured output voltage shift.
C
2
V
DD
10 µF
C
3
100 pF
RFin
+
-
Out
R
1
50W
C
4
C
1
100 pF
22 pF
C
5
V
SS
10 µF
Figure 51. Circuit for coupling the RF signal to IN+
Cell Phone Call
The effect of electromagnetic interference is demonstrated in a setup where a cell phone interferes with a
pressure sensor application. The application is shown in Figure 53.
This application needs two op amps and therefore a dual op amp is used. The op amp configured as a buffer
and connected at the negative output of the pressure sensor prevents the loading of the bridge by resistor R2.
The buffer also prevents the resistors of the sensor from affecting the gain of the following gain stage. The op
amps are placed in a single supply configuration.
The experiment is performed on two different dual op amps: a typical standard op amp and the LMV832, EMI
hardened dual op amp. A cell phone is placed on a fixed position a couple of centimeters from the op amps in
the sensor circuit.
When the cell phone is called, the PCB and wiring connected to the op amps receive the RF signal.
Subsequently, the op amps detect the RF voltages and currents that end up at their pins. The resulting effect on
the output of the second op amp is shown in Figure 52.
Typical Opamp
LMV832
TIME (0.5s/DIV)
Figure 52. Comparing EMI Robustness
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
www.ti.com
The difference between the two types of dual op amps is clearly visible. The typical standard dual op amp has an
output shift (disturbed signal) larger than 1V as a result of the RF signal transmitted by the cell phone. The
LMV832, EMI hardened op amp does not show any significant disturbances. This means that the RF signal will
not disturb the signal entering the ADC when using the LMV832.
R1
2.4 kW
V
DD
V
DD
R2
PRESSURE
SENSOR
-
100 W
LMV832
+
-
-
+
ADC
LMV832
V
OUT
+
Figure 53. Pressure Sensor Application
DECOUPLING AND LAYOUT
Care must be given when creating a board layout for the op amp. For decoupling the supply lines it is suggested
that 10 nF capacitors be placed as close as possible to the op amp. For single supply, place a capacitor between
V+ and V−. For dual supplies, place one capacitor between V+ and the board ground, and a second capacitor
between ground and V−. Even with the LMV831/LMV832/LMV834 inherent hardening against EMI, it is still
recommended to keep the input traces short and as far as possible from RF sources. Then the RF signals
entering the chip are as low as possible, and the remaining EMI can be, almost, completely eliminated in the chip
by the EMI reducing features of the LMV831/LMV832/LMV834.
PRESSURE SENSOR APPLICATION
The LMV831/LMV832/LMV834 can be used for pressure sensor applications. Because of their low power the
LMV831/LMV832/LMV834 are ideal for portable applications, such as blood pressure measurement devices, or
portable barometers. This example describes a universal pressure sensor that can be used as a starting point for
different types of sensors and applications.
Pressure Sensor Characteristics
The pressure sensor used in this example functions as a Wheatstone bridge. The value of the resistors in the
bridge change when pressure is applied to the sensor. This change of the resistor values will result in a
differential output voltage, depending on the sensitivity of the sensor and the applied pressure. The difference
between the output at full scale pressure and the output at zero pressure is defined as the span of the pressure
sensor. A typical value for the span is 100 mV. A typical value for the resistors in the bridge is 5 kΩ. Loading of
the resistor bridge could result in incorrect output voltages of the sensor. Therefore the selection of the circuit
configuration, which connects to the sensor, should take into account a minimum loading of the sensor.
Pressure Sensor Example
The configuration shown in Figure 53 is simple, and is very useful for the read out of pressure sensors. With two
op amps in this application, the dual LMV832 fits very well. The op amp configured as a buffer and connected at
the negative output of the pressure sensor prevents the loading of the bridge by resistor R2. The buffer also
prevents the resistors of the sensor from affecting the gain of the following gain stage. Given the differential
output voltage VS of the pressure sensor, the output signal of this op amp configuration, VOUT, equals:
VDD VS
≈
’
R1
R2
-
1
VOUT
=
∆
2
+ ×
÷
÷
∆
2
2
«
◊
(2)
To align the pressure range with the full range of an ADC, the power supply voltage and the span of the pressure
sensor are needed. For this example a power supply of 5V is used and the span of the sensor is 100 mV. When
a 100Ω resistor is used for R2, and a 2.4 kΩ resistor is used for R1, the maximum voltage at the output is 4.95V
and the minimum voltage is 0.05V. This signal is covering almost the full input range of the ADC. Further
processing can take place in the microprocessor following the ADC.
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV831 LMV832 LMV834
LMV831, LMV832, LMV834
www.ti.com
SNOSAZ6B –AUGUST 2008–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 18
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LMV831 LMV832 LMV834
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
LMV831MG/NOPB
LMV831MGE/NOPB
LMV831MGX/NOPB
LMV832MM/NOPB
LMV832MME/NOPB
LMV832MMX/NOPB
LMV834MT/NOPB
LMV834MTX/NOPB
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
SC70
SC70
DCK
5
5
1000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
AFA
AFA
AFA
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DCK
DCK
DGK
DGK
DGK
PW
250
3000
1000
250
Green (RoHS
& no Sb/Br)
SC70
5
Green (RoHS
& no Sb/Br)
VSSOP
VSSOP
VSSOP
TSSOP
TSSOP
8
Green (RoHS
& no Sb/Br)
AU5A
AU5A
AU5A
8
Green (RoHS
& no Sb/Br)
8
3500
94
Green (RoHS
& no Sb/Br)
14
14
Green (RoHS
& no Sb/Br)
LMV834
MT
PW
2500
Green (RoHS
& no Sb/Br)
LMV834
MT
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMV831MG/NOPB
LMV831MGE/NOPB
LMV831MGX/NOPB
LMV832MM/NOPB
LMV832MME/NOPB
LMV832MMX/NOPB
LMV834MTX/NOPB
SC70
SC70
DCK
DCK
DCK
DGK
DGK
DGK
PW
5
5
1000
250
178.0
178.0
178.0
178.0
178.0
330.0
330.0
8.4
8.4
2.25
2.25
2.25
5.3
2.45
2.45
2.45
3.4
1.2
1.2
1.2
1.4
1.4
1.4
1.6
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q1
Q1
Q1
Q1
SC70
5
3000
1000
250
8.4
8.0
VSSOP
VSSOP
VSSOP
TSSOP
8
12.4
12.4
12.4
12.4
12.0
12.0
12.0
12.0
8
5.3
3.4
8
3500
2500
5.3
3.4
14
6.95
8.3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMV831MG/NOPB
LMV831MGE/NOPB
LMV831MGX/NOPB
LMV832MM/NOPB
LMV832MME/NOPB
LMV832MMX/NOPB
LMV834MTX/NOPB
SC70
SC70
DCK
DCK
DCK
DGK
DGK
DGK
PW
5
5
1000
250
210.0
210.0
210.0
210.0
210.0
367.0
367.0
185.0
185.0
185.0
185.0
185.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
SC70
5
3000
1000
250
VSSOP
VSSOP
VSSOP
TSSOP
8
8
8
3500
2500
14
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
LMV832MMX
LMV831 Single/ LMV832 Dual/ LMV834 Quad 3.3 MHz Low Power CMOS, EMI Hardened Operational Amplifiers
TI
LMV832MMX/NOPB
Dual, 5.5-V, 3.3-MHz, low noise (12-nV/√Hz) operational amplifier | DGK | 8 | -40 to 125
TI
LMV834
LMV831 Single/ LMV832 Dual/ LMV834 Quad 3.3 MHz Low Power CMOS, EMI Hardened Operational Amplifiers
TI
LMV834MT
LMV831 Single/ LMV832 Dual/ LMV834 Quad 3.3 MHz Low Power CMOS, EMI Hardened Operational Amplifiers
TI
LMV834MTX
LMV831 Single/ LMV832 Dual/ LMV834 Quad 3.3 MHz Low Power CMOS, EMI Hardened Operational Amplifiers
TI
LMV834MTX/NOPB
Quad 3.3 MHz Low Power CMOS, EMI Hardened Operational Amplifier 14-TSSOP -40 to 125
TI
LMV841
LMV841/LMV841Q/LMV842/LMV842Q/LMV844/LMV844Q CMOS Input, RRIO, Wide Supply Range Operational Amplifiers
TI
©2020 ICPDF网 联系我们和版权申明