LP3982IMM-3.3/NOPB [TI]
Micropower, Ultra-Low-Dropout, Low-Noise, 300-mA CMOS Regulator;型号: | LP3982IMM-3.3/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | Micropower, Ultra-Low-Dropout, Low-Noise, 300-mA CMOS Regulator 光电二极管 输出元件 调节器 |
文件: | 总23页 (文件大小:950K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
LP3982 Micropower, Ultra Low-Dropout, Low-Noise, 300 mA CMOS Regulator
Check for Samples: LP3982
1
FEATURES
DESCRIPTION
The LP3982 low-dropout (LDO) CMOS linear
regulator is available in 1.8V, 2.5V, 2.77V, 2.82V,
3.0V, 3.3V, and adjustable versions. They deliver 300
mA of output current. Packaged in an 8-Pin VSSOP,
the LP3982 is pin and package compatible with
Maxim's MAX8860. The LM3982 is also available in
the small footprint WSON package.
2
•
MAX8860 Pin, Package and Spec. Compatible
WSON Space Saving Package
300 mA Output Current
•
•
•
•
•
•
•
•
•
•
120 mV Typical Dropout @ 300 mA
90 μA Typical Quiescent Current
1 nA Typical Shutdown Mode
60 dB Typical PSRR
The LP3982 suits battery-powered applications
because of its shutdown mode (1nA typ), low
quiescent current (90 μA typ), and LDO voltage (120
mV typ). The low dropout voltage allows for more
utilization of a battery’s available energy by operating
closer to its end-of-life voltage. The LP3982's PMOS
output transistor consumes relatively no drive current
compared to PNP LDO regulators.
2.5V to 6V Input Range
120μs Typical Turn-on Time
Stable with Small Ceramic Output Capacitors
37 μV RMS Output Voltage Noise (10 Hz to 100
kHz)
•
•
Over-Temperature/Over-Current Protection
±2% Output Voltage Tolerance
This PMOS regulator is stable with small ceramic
capacitive loads (2.2 μF typ).
These devices also include regulation fault detection,
a bandgap voltage reference, constant current limiting
and thermal overload protection.
APPLICATIONS
•
•
•
•
Wireless Handsets
DSP Core Power
Battery Powered Electronics
Portable Information Appliances
Application Circuit
V
O
V
IN
OUT
IN
2.2PF
2.2PF
CERAMIC
100k
SHDN
FAULT
CC
GND
33n
F
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2013, Texas Instruments Incorporated
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS(1)(2)(3)
VIN, VOUT, VSHDN, VSET, VCC, VFAULT
−0.3V to 6.5V
20mA
Fault Sink Current
Power Dissipation
See(4)
Storage Temperature Range
Junction Temperature (TJ)
Lead Temperature (10 sec.)
−65°C to 160°C
150°C
260°C
Human Body Model(5)
Machine Model
8-Pin VSSOP
2kV
ESD Rating
200V
223°C/W
See(4)
Thermal Resistance (θJA
)
8-Pin WSON
(1) Absolute Maximum ratings indicate limits beyond which damage may occur. Electrical specifications do not apply when operating the
device outside of its rated operating conditions.
(2) All voltages are with respect to the potential at the ground pin.
(3) If Military/Aerospace specified devices are required, please contact Texas Instruments Sales Office/Distributors for availability and
specifications.
T
- T
A
J(MAX)
P
D
=
T
JA
(4) Maximum Power dissipation for the device is calculated using the following equations:
where TJ(MAX) is the maximum
junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance. For example, for the VSSOP-
8 package θJA = 223°C/W, TJ(MAX) = 150°C and using TA = 25°C; the maximum power dissipation is found to be 561 mW. The derating
factor (−1/θJA) = −4.5 mW/°C, thus below 25°C the power dissipation figure can be increased by 4.5 mW per degree, and similarity
decreased by this factor for temperatures above 25°C. The value of the θJA for the WSON package is specifically dependent on the PCB
trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the
WSON package, refer to Application Note AN-1187 SNOA401.
(5) Human body model: 1.5 kΩ in series with 100 pF.
RECOMMENDED OPERATING CONDITIONS(1)(2)
Temperature Range
−40°C to 85°C
Supply Voltage
2.5V to 6.0V
(1) Absolute Maximum ratings indicate limits beyond which damage may occur. Electrical specifications do not apply when operating the
device outside of its rated operating conditions.
(2) All voltages are with respect to the potential at the ground pin.
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, all limits specified for VIN = VO +0.5V(1), VSHDN = VIN, CIN = COUT = 2.2μF, CCC = 33nF, TJ = 25°C.
Boldface limits apply for the operating temperature extremes: −40°C and 85°C.
Symbol
VIN
Parameter
Input Voltage
Conditions
Min(2)
Typ(3)
Max(2)
Units
2.5
6.0
V
ΔVO
Output Voltage Tolerance
100 μA ≤ IOUT ≤ 300 mA
VIN = VO +0.5V(1)
SET = OUT for the Adjust Versions
−2
+2
% of VOUT
(NOM)
−3
+3
VO
IO
Output Adjust Range
Maximum Output Current
Output Current Limit
Supply Current
Adjust Version Only
1.25
300
330
6
V
Average DC Current Rating
mA
mA
ILIMIT
IQ
770
90
IOUT = 0mA
270
μA
μA
IOUT = 300 mA
225
Shutdown Supply Current
VO = 0V, SHDN = GND
0.001
1
(1) Condition does not apply to input voltages below 2.5V since this is the minimum input operating voltage.
(2) All limits are verified by testing or statistical analysis.
(3) Typical Values represent the most likely parametric norm.
2
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise specified, all limits specified for VIN = VO +0.5V(1), VSHDN = VIN, CIN = COUT = 2.2μF, CCC = 33nF, TJ = 25°C.
Boldface limits apply for the operating temperature extremes: −40°C and 85°C.
Symbol
VDO
Parameter
Dropout Voltage(1)(4)
Conditions
Min(2)
−0.1
2
Typ(3)
Max(2)
Units
IOUT = 1 mA
0.4
IOUT = 200 mA
80
220
mV
IOUT = 300 mA
120
0.01
0.002
37
ΔVO
en
Line Regulation
IOUT = 1 mA, (VO + 0.5V) ≤ VI ≤ 6V(1)
100 μA ≤ IOUT ≤ 300 mA
IOUT = 10 mA, 10 Hz ≤ f ≤ 100 kHz
10 Hz ≤ f ≤ 100 kHz, COUT = 10 μF
VIH, (VO + 0.5V) ≤ VI ≤ 6V(1)
VIL, (VO + 0.5V) ≤ VI ≤ 6V(1)
SHDN = GND or IN
0.1
%/V
Load Regulation
%/mA
μVRMS
nV/√Hz
Output Voltage Noise
Output Voltage Noise Density
SHDN Input Threshold
190
VSHDN
V
0.4
100
2.5
ISHDN
ISET
SHDN Input Bias Current
SET Input Leakage
0.1
0.1
nA
nA
mV
V
SET = 1.3V, Adjust Version Only(5)
VFAULT
FAULTDetection Voltage
FAULT Output Low Voltage
FAULT Off-Leakage Current
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Start-Up Time
V
O ≥ 2.5V, IOUT = 200 mA(6)
120
0.115
0.1
280
0.25
100
ISINK = 2 mA
IFAULT
TSD
FAULT = 3.6V, SHDN = 0V
nA
160
10
°C
TON
COUT = 10 μF, VO at 90% of Final
120
μs
Value
(4) Dropout voltage is measured by reducing VIN until VO drops 100mV from its nominal value at VIN -VO = 0.5V. Dropout Voltage does not
apply to the 1.8 version.
(5) The SET pin is not externally connected for the fixed versions.
(6) The FAULT detection voltage is specified for the input to output voltage differential at which the FAULT pin goes active low.
FUNCTIONAL BLOCK DIAGRAM
V
IN
V
O
FAST
START-UP
CIRCUIT
CURRENT
LIMIT
R1
+
-
SET
CC
ERROR
AMP
FAULT
COMPARATORS
FAULT
SHDN
OFF
R2
1.25V
BANDGAP
THERMAL
PROTECTION
GND
Figure 1.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LP3982
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise specified, VIN = VO + 0.5V, CIN = COUT = 2.2 μF, CCC = 33 nF, TJ = 25°C, VSHDN = VIN.
Dropout Voltage vs. Load Current
(For Different Output Voltages)
Dropout Voltage vs. Load Current
(For Different Output Temperatures)
160
140
120
100
80
140
120
100
80
V
= 2.77V
O
25°C
85°C
V
= 2.5V
O
V
= 3.3V
O
-40°C
60
60
40
40
20
0
20
0
50
100
150
200
250
300
50
100 150
200
250 300
0
0
LOAD CURRENT (mA)
LOAD CURRENT (mA)
Figure 2.
Figure 3.
FAULT Detect Threshold vs. Load Current
180
Supply Current vs. Input Voltage
= 0mA
240
220
200
180
160
140
120
100
80
I
L
160
140
FAULT = HIGH
T
A
= 85°C
120
100
80
60
40
20
0
T
= 25°C
A
FAULT = LOW
60
T
= -40°C
A
40
20
0
0
50
100
150
200
250
300
0
2
3
4
5
6
1
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
Figure 4.
Figure 5.
Supply Current vs. Load Current
Power Supply Rejection Ratio vs. Frequency
0
250
200
150
100
50
85°C
-10
-20
-30
-40
-50
-60
-70
25°C
-40°C
0
0
50
100
150
200
250
300
10
10k
100k
100
1k
LOAD CURRENT (mA)
FREQUENCY (Hz)
Figure 6.
Figure 7.
4
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, VIN = VO + 0.5V, CIN = COUT = 2.2 μF, CCC = 33 nF, TJ = 25°C, VSHDN = VIN.
Output Noise Spectral Density
Output Noise (10Hz to 100kHz)
10
1
C
= 10PF
OUT
0.1
0.01
C
= 2.2PF
OUT
10
k
1 ms/DIV
100
1k
100k
FREQUENCY (Hz)
Figure 8.
Figure 9.
Output Impedance vs. Frequency
Line Transient Response
2
1.8
1.6
1.4
1.2
1
I
=
L
300mA
4.3V
3.3V
0.8
0.6
0.4
0.2
0
500 Ps/DIV
10
100
10k
1k
100k
FREQUENCY (Hz)
Figure 10.
Figure 11.
Load Transient
Shutdown Response
I
L
=
300mA
V
SHDN
V
OUT
0V
V
OUT
I
OUT
0V
500 Ps/DIV
500ꢀPs/DIV
Figure 12.
Figure 13.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LP3982
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, VIN = VO + 0.5V, CIN = COUT = 2.2 μF, CCC = 33 nF, TJ = 25°C, VSHDN = VIN.
Power-Up Response
Power-Down Response
FAULT
FAULT
V
IN
V
IN
V
IN
V
O
V
O
V
IN
V
O
V
O
5 ms/DIV
Figure 15.
5 mS/DIV
Figure 14.
6
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
APPLICATION INFORMATION
General Information
The LP3982 is package, pin and performance compatible with Maxim's MAX8860 excluding reverse battery
protection and Dual Mode function (fixed and adjustable combined).
Figure 16 shows the functional block diagram for the LP3982. A 1.25V bandgap reference, an error amplifier and
a PMOS pass transistor perform voltage regulation while being supported by shutdown, fault, and the usual
Temperature and current protection circuitry
The regulator's topology is the classic type with negative feedback from the output to one of the inputs of the
error amplifier. Feedback resistors R1 and R2 are either internal or external to the IC, depending on whether it is
the fixed voltage version or the adjustable version. The negative feedback and high open loop gain of the error
amplifier cause the two inputs of the error amplifier to be virtually equal in voltage. If the output voltage changes
due to load changes, the error amplifier provides the appropriate drive to the pass transistor to maintain the error
amplifier's inputs as virtually equal. In short, the error amplifier keeps the output voltage constant in order to keep
its inputs equal.
V
IN
V
O
FAST
START-UP
CIRCUIT
CURRENT
LIMIT
R1
+
-
SET
CC
ERROR
AMP
FAULT
COMPARATORS
FAULT
SHDN
OFF
R2
1.25V
BANDGAP
THERMAL
PROTECTION
GND
Figure 16. Functional Block Diagram for the LP3982
Output Voltage Setting (Adj Version Only)
The output voltage is set according to the amount of negative feedback (Note that the pass transistor inverts the
feedback signal.) Figure 17 simplifies the topology of the LP3982. This type of regulator can be represented as
an op amp configured as non-inverting amplifier and a fixed DC Voltage (VREF) for its input signal. The special
characteristic of this op amp is its extra-large output transistor that only sources current. In terms of its non-
inverting configuration, the output voltage equals VREF times the closed loop gain:
R
1
1
V
=
V
O
+
REF
R
2
(1)
Utilize the following equation for adjusting the output to a particular voltage:
VO
é
ù
R1 = R2
-1
ê
ú
1.25V
ë
û
(2)
Choose R2 = 100k to optimize accuracy, power supply rejection, noise and power consumption.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LP3982
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
V
IN
V
REF
+
-
V
OUT
R
1
R
2
Figure 17. Regulator Topology Simplified
Similarity in the output capabilities exists between op amps and linear regulators. Just as rail-to-rail output op
amps allow their output voltage to approach the supply voltage, low dropout regulators (LDOs) allow their output
voltage to operate close to the input voltage. Both achieve this by the configuration of their output transistors.
Standard op amps and regulator outputs are at the source (or emitter) of the output transistor. Rail-to-rail op amp
and LDO regulator outputs are at the drain (or collector) of the output transistor. This replaces the threshold (or
diode drop) limitations on the output with the less restrictive source-to-drain (or VSAT) limitations. There is a trade-
off, of course. The output impedance become significantly higher, thus providing a critically lower pole when
combined with the capacitive load. That's why rail-to-rail op amps are usually poor at driving capacitive loads and
recommend a series output resistor when doing so. LDOs require the same series resistance except that the
internal resistance of the output capacitor will usually suffice. Refer to the Output Capacitance section for more
information.
Output Capacitance
The LP3982 is specifically designed to employ ceramic output capacitors as low as 2.2 μF. Ceramic capacitors
below 10μF offer significant cost and space savings, along with high frequency noise filtering. Higher values and
other types and of capacitor may be used, but their equivalent series resistance (ESR) should be maintained
below 0.5Ω
Ceramic capacitor of the value required by the LP3982 are available in the following dielectric types: Z5U, Y5V,
X5R and X7R. The Z5U and Y5V types exhibit a 50% or more drop in capacitance value as their temperature
increases from 25°C, an important consideration. The X5R generally maintain their capacitance value within
±20%. The X7R type are desirable for their tighter tolerance of 10% over temperature.
Ceramic capacitors pose a challenge because of their relatively low ESR. Like most other LDOs, the LP3982
relies on a zero in the frequency response to compensate against excessive phase shift in the regulator's
feedback loop. If the phase shift reaches 360° (i.e.; becomes positive), the regulator will oscillate. This
compensation usually resides in the zero generated by the combination of the output capacitor with its equivalent
series resistance (ESR). The zero is intended to cancel the effects of the pole generated by the load capacitance
(CL) combined with the parallel combination of the load resistance (RL) and the output resistance (RO) of the
regulator. The challenge posed by low ESR capacitors is that the zero it generates can be too high in frequency
for the pole that it's intended to compensate. The LP3982 overcomes this challenge by internally generating a
strategically placed zero.
8
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
LOOP
GAIN
-
R
O
V
REF
+
C
L
R
L
Figure 18. Simplified Model of Regulator Loop Gain Components
Figure 18 shows a basic model for the linear regulator that helps describe what happens to the output signal as it
is processed through its feedback loop; that is, describe its loop gain (LG). The LG includes two main transfer
functions: the error amplifier and the load. The error amplifier provides voltage gain and a dominant pole, while
the load provides a zero and a pole. The LG of the model in Figure 18 is described by the following equation:
A
1 + jω (ESR x C )
O
L
(jω)
LG
=
*
ω
1 + jω ((ESR + R // R ) C )
L
O
L
1 + j
ω
POLE
(3)
The first term of the above equation expresses the voltage gain (numerator) and a single pole role-off
(denominator) of the error amplifier. The second term expresses the zero (numerator) and pole (denominator) of
the load in combination with the RO of the regulator.
Figure 19 shows a Bode plot that represents a case where the zero contributed by the load is too high to cancel
the effect of the pole contributed by the load and RO. The solid line illustrates the loop gain while the dashed line
illustrates the corresponding phase shift. Notice that the phase shift at unity gain is a total 360° -the criteria for
oscillation.
ERROR AMP
POLE: Z
POLE
-180°
LOAD POLE
1/(2S (ESR + R // R )C )
O
L
L
0 dB
-360°
LOAD ZERO
1/(2S (ESR x C )
L
Figure 19. Loop Gain Bode Plot Illustrating Inadequately High Zero for Stability Compensation
The LP3982 generates an internal zero that makes up for the inadequately high zero of the low ESR ceramic
output capacitor. This internally generated zero is strategically placed to provide positive phase shift near unity
gain, thus providing a stable phase margin.
No-Load Stability
The LP3982 remains stable during no-load conditions, a necessary feature for CMOS RAM keep-alive
applications.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LP3982
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
Input Capacitor
The LP3982 requires a minimum input capacitance of about 1μF. The value may be increased indefinitely. The
type is not critical to stability. However, instability may occur with bench set-ups where long supply leads are
used, particularly at near dropout and high current conditions. This is attributed to the lead inductance coupling to
the output through the gate oxide of the pass transistor; thus, forming a pseudo LCR network within the Loop-
gain. A 10 μF tantalum input capacitor remedies this non-situ condition; its larger ESR acts to dampen the
pseudo LCR network. This may only be necessary for some bench setups. 1 μF ceramic input capacitor are fine
for most end-use applications.
If a tantalum input capacitor is intended for the final application, it is important to consider their tendency to fail in
short circuit mode, thus potentially damaging the part.
Noise Bypass Capacitor
The noise bypass capacitor (CC) significantly reduces output noise of the LP3982. It connects between pin 6 and
ground. The optimum value for CC is 33 nF.
Pin 6 directly connects to the high impedance output of the bandgap. The DC leakage of the CC capacitor should
be considered; loading down the reference will reduce the output voltage. NPO and COG ceramic capacitors
typically offer very low leakage. Polypropylene and polycarbonate film carbonate capacitor offer even lower
leakage currents.
CC does not affect the transient response; however, it does affect turn-on time. The smaller the CC value, the
quicker the turn-on time.
Power Dissipation
Power dissipation refers to the part's ability to radiate heat away from the silicon, with packaging being a key
factor. A reasonable analogy is the packaging a human being might wear, a jacket for example. A jacket keeps a
person comfortable on a cold day, but not so comfortable on a hot day. It would be even worse if the person was
exerting power (exercising). This is because the jacket has resistance to heat flow to the outside ambient air, like
the IC package has a thermal resistance from its junctions to the ambient (θJA).
θJA has a unit of temperature per power and can be used to calculate the IC's junction temperature as follows:
TJ = θJA (PD) + TA
•
•
•
•
TJ is the junction temperature of the IC
θJA is the thermal resistance from the junction to the ambient air outside the package
PD is the power exerted by the IC
TA is the ambient temperature
(4)
PD is calculated as follows:
PD = IOUT (VIN -VO)
•
•
•
•
θJA for the LP3982 package (VSSOP-8) is 223°C/W with no forced air flow
182°C/W with 225 linear feet per minute (LFPM) of air flow
163°C/W with 500 LFPM of air flow
149°C/W with 900 LFPM of air flow
(5)
θJA can also be decreased (improved) by considering the layout of the PC board: heavy traces (particularly at VIN
and the two VOUT pins), large planes, through-holes, etc.
Improvements and absolute measurements of the θJA can be estimated by utilizing the thermal shutdown circuitry
that is internal to the IC. The thermal shutdown turns off the pass transistor of the device when its junction
temperature reaches 160°C (Typical). The pass transistor doesn't turn on again until the junction temperature
drops about 10°C (hysteresis).
Using the thermal shutdown circuit to estimate , θJA can be done as follows: With a low input to output voltage
differential, set the load current to 300 mA. Increase the input voltage until the thermal shutdown begins to cycle
on and off. Then slowly decrease VIN (100 mV increments) until the part stays on. Record the resulting voltage
differential (VD) and use it in the following equation:
10
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
(160 - T )
A
T
JA
(0.300 x V )
D
(6)
Fault Detection
The LP3982 provides a FAULT pin that goes low during out of regulation conditions like current limit and thermal
shutdown, or when it approaches dropout. The latter monitors the input-to-output voltage differential and
compares it against a threshold that is slightly above the dropout voltage. This threshold also tracks the dropout
voltage as it varies with load current. Refer to Figure 4 in the typical characteristics section.
The FAULT pin requires a pull-up resistor since it is an open-drain output. This resistor should be large in value
to reduce energy drain. A 100 kΩ pull-up resistor works well for most applications.
Figure 20 shows the LP3985 with delay added to the FAULT pin for the reset pin of a microprocessor. The
output of the comparator stays low for a preset amount of time after the regulator comes out of a fault condition.
V
= 3V
O
V
IN
IN
OUT
LP3982
R
P
100k
SHDN
GND
FAULT
CC
+
C
DELAY
LMC7225
RESET
0.1PF
-
Figure 20. Power on Delayed Reset Application
The delay time for the application of Figure 20 is set as follows:
-t
C
DELAY
=
V
REF
R
P
ln
1
-
V
O
(7)
The application is set for a reset delay time of 8.8 ms. Note that the comparator should have high impedance
inputs so as to not load down the VREF at the CC pin of the LP3982.
Shutdown
The LP3982 goes into sleep mode when the SHDN pin is in a logic low condition. During this condition, the pass
transistor, error amplifier, and bandgap are turned off, reducing the supply current to 1 nA typical. The maximum
voltage for a logic low at the SHDN pin is 0.4V. A minimum voltage of 2V at the SHDN pin will turn the LP3982
back on. The SHDN pin may be directly tied to VIN to keep the part on. The SHDN pin may exceed VIN but not
the ABS MAX of 6.5V.
Figure 21 shows an application that uses the SHDN pin. It detects when the battery is too low and disconnects
the load by turning off the regulator. A micropower comparator (LMC7215) and reference (LM385) are combined
with resistors to set the minimum battery voltage. At the minimum battery voltage, the comparator output goes
low and tuns off the LP3982 and corresponding load. Hysteresis is added to the minimum battery threshold to
prevent the battery's recovery voltage from falsely indicating an above minimum condition. When the load is
disconnected from the battery, it automatically increases in terminal voltage because of the reduced IR drop
across its internal resistance. The Minimum battery detector of Figure 21 has a low detection threshold (VLT) of
3.6V that corresponds to the minimum battery voltage. The upper threshold (VUT) is set for 4.6V in order to
exceed the recovery voltage of the battery.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LP3982
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
V
B
OUT
IN
R1
768k
R4
180k
R2
2.2PF
2.2PF
CERAMIC
2.74M
LP3982
100k
V
B
+
FAULT
GND
4 Cells
NiMH
SHDN
LMC7215
-
R3
301k
V
REF
LM385A-1.2V
Figure 21. Minimum Battery Detector that Disconnects the Load Via the SHDN Pin of the LP3982
Resistor value for VUT and VLT are determined as follows:
1
1
1
+
+
G
=
T
R
R
1
R
2
3
V
V
= R (V
) G
UT
1
REF
T
= R // R (V
) G
T
LT
1
2
REF
(8)
(The application of Figure 21 used a GT of 5μ mho)
V
UT1
R
1
=
V
(G )
T
REF
(9)
(10)
(11)
1
R
=
2
V
(G )
T
REF
V
1
-
R
LT
1
1
1
R
=
3
1
R
2
-
+
G
T
R
1
The above procedure assumes a rail-to-rail output comparator. Essentially, R2 is in parallel with R1 prior to
reaching the lower threshold, then R2 becomes parallel with R3 for the upper threshold. Note that the application
requires rail-to-rail input as well.
The resistor values shown in Figure 21 are the closest practical to calculated values.
Fast Start-Up
The LP3982 provides fast start-up time for better system efficiency. The start-up speed is maintained when using
the optional noise bypass capacitor. An internal 500 μA current source charges the capacitor until it reaches
about 90% of its final value.
12
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
LP3982
www.ti.com
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
Connection Diagram
The set pin is internally disconnected for the fixed versions.
1
8
OUT
FAULT
OUT
1
2
3
4
8
FAULT
2
3
7
6
5
SHD
N
7
6
5
SHDN
CC
IN
GND
OUT
IN
GND
OUT
GND
CC
SET
4
SET *
Figure 22. 8-Pin VSSOP
Top View
Figure 23. 8-Pin WSON Surface Mount
Top View
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LP3982
LP3982
SNVS185D –FEBRUARY 2002–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 13
14
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LP3982
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
1000
1000
(1)
(2)
(6)
(3)
(4/5)
LP3982ILD-1.8
NRND
ACTIVE
WSON
WSON
NGM
8
8
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LNB
LNB
LP3982ILD-1.8/NOPB
NGM
Green (RoHS
& no Sb/Br)
Level-3-260C-168 HR
LP3982ILD-2.5/NOPB
LP3982ILD-3.0/NOPB
LP3982ILD-3.3/NOPB
LP3982ILD-ADJ/NOPB
LP3982ILDX-1.8/NOPB
LP3982ILDX-3.0/NOPB
LP3982ILDX-3.3/NOPB
LP3982ILDX-ADJ/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
8
8
8
8
8
8
8
8
1000
1000
1000
1000
4500
4500
4500
4500
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
LPB
LTB
LUB
LVB
LNB
LTB
LUB
LVB
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
LP3982IMM-1.8
NRND
VSSOP
VSSOP
DGK
DGK
8
8
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LENB
LENB
LP3982IMM-1.8/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3982IMM-2.5
NRND
VSSOP
VSSOP
DGK
DGK
8
8
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LEPB
LEPB
LP3982IMM-2.5/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3982IMM-3.0
NRND
VSSOP
VSSOP
DGK
DGK
8
8
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LETB
LETB
LP3982IMM-3.0/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3982IMM-3.3
NRND
VSSOP
VSSOP
DGK
DGK
8
8
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LEUB
LEUB
LP3982IMM-3.3/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3982IMM-ADJ
NRND
VSSOP
DGK
8
1000
TBD
Call TI
Call TI
-40 to 85
LEVB
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
LP3982IMM-ADJ/NOPB
LP3982IMMX-1.8/NOPB
LP3982IMMX-2.5/NOPB
LP3982IMMX-2.82/NOPB
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
DGK
8
8
8
8
1000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
LEVB
LENB
LEPB
LESB
ACTIVE
ACTIVE
ACTIVE
DGK
DGK
DGK
3500
3500
3500
Green (RoHS
& no Sb/Br)
-40 to 85
Green (RoHS
& no Sb/Br)
-40 to 85
Green (RoHS
& no Sb/Br)
-40 to 85
LP3982IMMX-ADJ
NRND
VSSOP
VSSOP
DGK
DGK
8
8
3500
3500
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LEVB
LEVB
LP3982IMMX-ADJ/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP3982ILD-1.8
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1000
1000
1000
1000
1000
1000
4500
4500
4500
4500
1000
1000
1000
1000
1000
1000
1000
1000
178.0
178.0
178.0
178.0
178.0
178.0
330.0
330.0
330.0
330.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
5.3
5.3
5.3
5.3
5.3
5.3
5.3
5.3
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
LP3982ILD-1.8/NOPB
LP3982ILD-2.5/NOPB
LP3982ILD-3.0/NOPB
LP3982ILD-3.3/NOPB
LP3982ILD-ADJ/NOPB
LP3982ILDX-1.8/NOPB
LP3982ILDX-3.0/NOPB
LP3982ILDX-3.3/NOPB
LP3982ILDX-ADJ/NOPB WSON
LP3982IMM-1.8 VSSOP
LP3982IMM-1.8/NOPB VSSOP
LP3982IMM-2.5 VSSOP
LP3982IMM-2.5/NOPB VSSOP
LP3982IMM-3.0 VSSOP
LP3982IMM-3.0/NOPB VSSOP
LP3982IMM-3.3 VSSOP
LP3982IMM-3.3/NOPB VSSOP
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP3982IMM-ADJ
VSSOP
DGK
DGK
DGK
DGK
DGK
DGK
DGK
8
8
8
8
8
8
8
1000
1000
3500
3500
3500
3500
3500
178.0
178.0
330.0
330.0
330.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
12.4
5.3
5.3
5.3
5.3
5.3
5.3
5.3
3.4
3.4
3.4
3.4
3.4
3.4
3.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
LP3982IMM-ADJ/NOPB VSSOP
LP3982IMMX-1.8/NOPB VSSOP
LP3982IMMX-2.5/NOPB VSSOP
LP3982IMMX-2.82/NOPB VSSOP
LP3982IMMX-ADJ
VSSOP
LP3982IMMX-ADJ/NOPB VSSOP
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LP3982ILD-1.8
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
NGM
8
8
8
8
8
8
8
8
8
8
1000
1000
1000
1000
1000
1000
4500
4500
4500
4500
210.0
213.0
213.0
213.0
213.0
213.0
367.0
367.0
367.0
367.0
185.0
191.0
191.0
191.0
191.0
191.0
367.0
367.0
367.0
367.0
35.0
55.0
55.0
55.0
55.0
55.0
35.0
35.0
35.0
35.0
LP3982ILD-1.8/NOPB
LP3982ILD-2.5/NOPB
LP3982ILD-3.0/NOPB
LP3982ILD-3.3/NOPB
LP3982ILD-ADJ/NOPB
LP3982ILDX-1.8/NOPB
LP3982ILDX-3.0/NOPB
LP3982ILDX-3.3/NOPB
LP3982ILDX-ADJ/NOPB
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LP3982IMM-1.8
LP3982IMM-1.8/NOPB
LP3982IMM-2.5
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
3500
3500
3500
3500
3500
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
367.0
367.0
367.0
367.0
367.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LP3982IMM-2.5/NOPB
LP3982IMM-3.0
LP3982IMM-3.0/NOPB
LP3982IMM-3.3
LP3982IMM-3.3/NOPB
LP3982IMM-ADJ
LP3982IMM-ADJ/NOPB
LP3982IMMX-1.8/NOPB
LP3982IMMX-2.5/NOPB
LP3982IMMX-2.82/NOPB
LP3982IMMX-ADJ
LP3982IMMX-ADJ/NOPB
Pack Materials-Page 3
MECHANICAL DATA
NGM0008C
LDA08C (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
LP3982IMMX-2.5/NOPB
IC VREG 2.5 V FIXED POSITIVE LDO REGULATOR, 0.22 V DROPOUT, PDSO8, MSOP-8, Fixed Positive Single Output LDO Regulator
NSC
©2020 ICPDF网 联系我们和版权申明