LP3990MF-2.5/NOPB [TI]
暂无描述;
| 型号： | LP3990MF-2.5/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 暂无描述 线性稳压器IC 调节器 电源电路 光电二极管 输出元件 PC |
| 文件： | 总24页 (文件大小：979K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
LP3990 150mA Linear Voltage Regulator for Digital Applications
Check for Samples: LP3990
1
FEATURES
APPLICATIONS
2
•
•
•
•
•
1% Voltage Accuracy at Room Temperature
Stable with Ceramic Capacitor
•
•
Cellular Handsets
Hand-Held Information Appliances
Logic Controlled Enable
DESCRIPTION
No Noise Bypass Capacitor Required
Thermal-Overload and Short-Circuit Protection
The LP3990 regulator is designed to meet the
requirements of portable, battery-powered systems
providing an accurate output voltage, low noise, and
low quiescent current. The LP3990 will provide a
0.8V output from the low input voltage of 2V at up to
150mA load current. When switched into shutdown
mode via a logic signal at the enable pin, the power
consumption is reduced to virtually zero.
KEY SPECIFICATIONS
•
•
•
•
•
•
•
•
•
Input Voltage Range, 2.0 to 6.0V
Output Voltage Range, 0.8 to 3.3V
Output Current, 150mA
Output Stable - Capacitors, 1.0µF
Virtually Zero IQ (Disabled), <10nA
Very Low IQ (Enabled), 43µA
Low Output Noise, 150µVRMS
PSRR, 55dB at 1kHz
The LP3990 is designed to be stable with space
saving ceramic capacitors as small as 1.0µF.
Performance is specified for a -40°C to 125°C
junction temperature range.
For output voltages other than 0.8V, 1.2, 1.35V, 1.5V,
1.8V, 2.5V, 2.8V, or 3.3V please contact your local
NSC sales office.
Fast Start Up, 105µs
PACKAGE
All available in Lead Free option.
•
•
•
4-Pin DSBGA, 1 mm x 1.3 mm
6-pin WQFN (SOT-23 Footprint)
SOT-23
For other package options contact your Texas Instruments sales
office.
Typical Application Circuit
LP3990
V
V
IN
IN
6
V
OUT
1.0 mF
V
OUT
1
1.0 mF
V
V
EN
EN
5
GND
2
(WQFN pin connections shown)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2013, Texas Instruments Incorporated
LP3990
SNVS251I –MAY 2004–REVISED MAY 2013
www.ti.com
PIN DESCRIPTIONS
Pin No
Symbol
Name and Function
WQFN
DSBGA
SOT-23
5
A2
3
VEN
Enable Input; Enables the Regulator when ≥ 0.95V.
Disables the Regulator when ≤ 0.4V.
Enable Input has 1MΩ pulldown resistor to GND.
2
1
A1
B1
2
5
GND
VOUT
Common Ground. Connect to Pad.
Voltage output. A 1.0µF Low ESR Capacitor should be connected to this Pin.
Connect this output to the load circuit.
6
3
B2
1
4
VIN
N/C
N/C
GND
Voltage Supply Input. A 1.0µF capacitor should be connected at this input.
No Connection. Do not connect to any other pin.
No Connection. Do not connect to any other pin.
Common Ground. Connect to Pin 2.
4
Pad
Connection Diagram
V
V
V
EN
V
IN
IN
EN
B2
A2
A2
B2
B1
A1
A1
B1
GND
GND
V
V
OUT
OUT
Bottom View
Top View
DSBGA, 4 Bump Package
See Package Number YZR0004
VIN
6
VEN
5
N/C
4
N/C
4
VEN
5
VIN
6
GND
GND
1
2
3
3
2
1
VOUT
Gnd
N/C
N/C
Gnd
VOUT
Top View
Bottom View
WQFN-6 Package
See Package Number NGG0006A
2
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LP3990
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
GND
2
V
V
IN
EN
3
1
4
5
N/C
V
OUT
SOT-23 Package
See Package Number DBV
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Input Voltage
-0.3 to 6.5V
-0.3 to (VIN + 0.3V) with 6.5V (max)
-0.3 to (VIN + 0.3V) with 6.5V (max)
150°C
Output Voltage
Enable Input Voltage
Junction Temperature
Lead/Pad Temp.(4)
WQFN/SOT-23
235°C
260°C
DSBGA
Storage Temperature
Continuous Power Dissipation Internally Limited(5)
ESD(6)
-65 to 150°C
Human Body Model
Machine Model
2KV
200V
(1) All Voltages are with respect to the potential at the GND pin.
(2) Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the
device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated
test conditions, see the Electrical Characteristics tables.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(4) For further information on these packages please refer to the following Application Notes; AN1112 DSBGA Package Wafer Level Chip
Scale Package, AN1187 Leadless Leadframe Package.
(5) Internal thermal shutdown circuitry protects the device from permanent damage.
(6) The human body model is 100pF discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor
discharged directly into each pin.
Operating Ratings(1)
Input Voltage
2V to 6V
0 to (VIN + 0.3V) with 6.0V (max)
-40°C to 125°C
Enable Input Voltage
Junction Temperature
Ambient Temperature TA Range
(2)
-40°C to 85°C
(1) Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the
device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated
test conditions, see the Electrical Characteristics tables.
(2) The maximum ambient temperature (TA(max)) is dependant on the maximum operating junction temperature (TJ(max-op) = 125°C), the
maximum power dissipation of the device in the application (PD(max)), and the junction to ambient thermal resistance of the part/package
in the application (θJA), as given by the following equation: TA(max) = TJ(max-op) - (θJA × PD(max)).
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LP3990
LP3990
SNVS251I –MAY 2004–REVISED MAY 2013
www.ti.com
Thermal Properties(1)
Junction To Ambient Thermal Resistance(2)
θJA(WQFN-6)
88°C/W
220°C/W
220°C/W
θJA(DSBGA)
θJA(SOT-23)
(1) Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the
device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated
test conditions, see the Electrical Characteristics tables.
(2) Junction to ambient thermal resistance is dependant on the application and board layout. In applications where high maximum power
dissipation is possible, special care must be paid to thermal dissipation issues in board design.
4
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LP3990
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
Electrical Characteristics
Unless otherwise noted, VEN =950mV, VIN = VOUT + 1.0V, or 2.0V, whichever is higher. CIN = 1 µF, IOUT = 1 mA, COUT =0.47
µF.
Typical values and limits appearing in normal type apply for TJ = 27°C. Limits appearing in boldface type apply over the full
(1)
junction temperature range for operation, −40 to +125°C.
Limit
Symbol
Parameter
Conditions
Typ
Units
Min
2
Max
6
(2)
VIN
Input Voltage
V
ΔVOUT
Output Voltage Tolerance
ILOAD = 1 mA
DSBGA
WQFN
SOT-23
DSBGA
WQFN
SOT-23
-1
+1
-1.5
-1.5
-2.5
-3
+1.5
+1.5
+2.5
+3
%
Over full line
and load
regulation.
-4
+4
Line Regulation Error
Load Regulation Error
VIN = (VOUT(NOM) + 1.0V) to 6.0V,
0.02
-0.1
-0.005
0.1
%/V
IOUT = 1mA
to 150mA
VOUT = 0.8 to 1.95V
DSBGA
0.002
0.005
VOUT = 0.8 to 1.95V
WQFN, SOT-23
0.003
0.0005
0.002
120
-0.008
-0.002
-0.005
0.008
0.002
0.005
200
%/mA
VOUT = 2.0 to 3.3V
DSBGA
VOUT = 2.0 to 3.3V
WQFN, SOT-23
VDO
ILOAD
IQ
Dropout Voltage
Load Current
IOUT = 150mA(3) (4)
mV
µA
(5) (4)
See
0
Quiescent Current
VEN = 950mV, IOUT = 0mA
VEN = 950mV, IOUT = 150mA
VEN = 0.4V
43
65
80
120
0.2
µA
0.002
550
(6)
ISC
Short Circuit Current Limit
Maximum Output Current
Power Supply Rejection Ratio
See
1000
mA
mA
IOUT
PSRR
150
f = 1kHz, IOUT = 1mA to 150mA
f = 10kHz, IOUT = 150mA
VOUT = 0.8
55
35
dB
µVRMS
°C
60
BW = 10Hz to
VOUT = 1.5
100kHz,
(4)
en
Output noise Voltage
125
180
155
15
VOUT = 3.3
TSHUTDOWN
Thermal Shutdown
Temperature
Hysteresis
Enable Control Characteristics
(7)
IEN
Maximum Input Current at VEN
Input
VEN = 0.0V
0.001
6
0.1
10
µA
VEN = 6V
2.5
VIL
VIH
Low Input Threshold
High Input Threshold
VIN = 2V to 6V
VIN = 2V to 6V
0.4
V
V
0.95
(1) All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production at TJ = 25°C or
correlated using Statistical Quality Control methods. Operation over the temperature specification is guaranteed by correlating the
electrical characteristics to process and temperature variations and applying statistical process control.
(2) VIN(MIN) = VOUT(NOM) + 0.5V, or 2.0V, whichever is higher.
(3) Dropout voltage is voltage difference between input and output at which the output voltage drops to 100mV below its nominal value.
This parameter only for output voltages above 2.0V.
(4) This electrical specification is guaranteed by design.
(5) The device maintains the regulated output voltage without the load.
(6) Short circuit current is measured with VOUT pulled to 0V and VIN worst case = 6.0V.
(7) Enable Pin has 1MΩ typical, resistor connected to GND.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LP3990
LP3990
SNVS251I –MAY 2004–REVISED MAY 2013
www.ti.com
Electrical Characteristics (continued)
Unless otherwise noted, VEN =950mV, VIN = VOUT + 1.0V, or 2.0V, whichever is higher. CIN = 1 µF, IOUT = 1 mA, COUT =0.47
µF.
Typical values and limits appearing in normal type apply for TJ = 27°C. Limits appearing in boldface type apply over the full
(1)
junction temperature range for operation, −40 to +125°C.
Limit
Symbol
Parameter
Conditions
Typ
Units
Min
Max
Timing Characteristics
(8)
TON
Turn On Time
To 95% Level
VIN(MIN) to 6.0V
VOUT = 0.8
VOUT = 1.5
VOUT = 3.3
80
150
200
250
105
175
µs
Transient
Response
Line Transient Response |δVOUT
|
Trise = Tfall = 30µs (8)δVIN = 600mV
mV
(pk - pk)
8
16
(8)
Load Transient Response |δVOUT
|
Trise = Tfall = 1µs
COUT = 1µF
I
= 1mA to 150mA
OUT
55
100
mV
(8) This electrical specification is guaranteed by design.
Output Capacitor, Recommended Specifications
Limit
Symbol
COUT
Parameter
Output Capacitance
Conditions
Nom
Units
Min
0.7
5
Max
Capacitance(1)
ESR
1.0
µF
500
mΩ
(1) The full operating conditions for the application should be considered when selecting a suitable capacitor to ensure that the minimum
value of capacitance is always met. Recommended capacitor type is X7R. However, dependent on application, X5R, Y5V, and Z5U can
also be used. (See Application Hints)
6
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LP3990
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
Typical Performance Characteristics
Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 0.47 µF Ceramic, VIN = VOUT(NOM) + 1.0V, TA = 25°C, VOUT(NOM)
1.5V , Shutdown pin is tied to VIN.
=
Output Voltage Change vs Temperature
Ground Current vs Load Current
2.00
1.50
1.00
0.50
0.00
-0.50
-1.00
-1.50
-2.00
80
70
60
50
40
30
20
10
0
T
= 125°C
J
T
= -40°C
J
T
J
= 25°C
0
25
50
LOAD CURRENT (mA)
Ground Current vs VIN. ILOAD = 1mA
75
100
125
150
-40 -25
0
25
50
75 100 125
TEMPERATURE (°C)
Ground Current vs VIN. ILOAD = 0mA
100
90
80
70
60
50
40
100
90
80
70
60
50
40
T
= 125°C
T = 125°C
J
J
T
J
= 25°C
T
J
= 25°C
T
J
= -40°C
T
J
= -40°C
30
20
30
20
2
2.5
3
3.5
4
4.5
5
5.5
6
2
2.5
3
3.5
4
4.5
5
5.5
6
V
V
IN
IN
Ground Current vs VIN. ILOAD = 150mA
100
Short Circuit Current
V
2.5V
IN =
800
90
80
70
60
50
40
600
400
200
0
T
= 125°C
J
T
J
= 25°C
T
J
= -40°C
30
20
TIME (100 ms/DIV)
2
2.5
3
3.5
4
4.5
5
5.5
6
V
IN
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LP3990
LP3990
SNVS251I –MAY 2004–REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 0.47 µF Ceramic, VIN = VOUT(NOM) + 1.0V, TA = 25°C, VOUT(NOM)
1.5V , Shutdown pin is tied to VIN.
=
Short Circuit Current
Line transient
C
C
= 1 mF
IN
V
6V
IN =
800
600
400
200
0
= 0.47 mF
OUT
IL = 1 to 150 mA
3.1
2.5
TIME (100 ms/DIV)
Power Supply Rejection Ratio
TIME (100 ms/DIV)
Power Supply Rejection Ratio
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-10
C
= 0.47 mF
C
OUT
= 1 mF
OUT
-20
-30
-40
-50
-60
-70
-80
-90
I
L
= 1 mA
I
= 150 mA
LOAD
C
= 0.47 mF
C
OUT
= 1 mF
OUT
100
1k
10k
100k
1M
100
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Enable Start-up Time
Enable Start-up Time
I
1 mA
I
150 mA
L =
L =
TIME (50 ms/DIV)
TIME (50 ms/DIV)
8
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LP3990
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 0.47 µF Ceramic, VIN = VOUT(NOM) + 1.0V, TA = 25°C, VOUT(NOM)
1.5V , Shutdown pin is tied to VIN.
=
Load Transient
Noise Density
10
C
C
= 1 mF
IN
OUT
= 0.47 mF
V
= 3.3V
OUT
1
V
= 1.5V
OUT
0.1
150
1
0.01
TIME (20 ms/DIV)
0.1
1
10
100
FREQUENCY (kHz)
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LP3990
LP3990
SNVS251I –MAY 2004–REVISED MAY 2013
www.ti.com
APPLICATION HINTS
EXTERNAL CAPACITORS
In common with most regulators, the LP3990 requires external capacitors for regulator stability. The LP3990 is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
INPUT CAPACITOR
An input capacitor is required for stability. It is recommended that a 1.0µF capacitor be connected between the
LP3990 input pin and ground (this capacitance value may be increased without limit).
This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean
analogue ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.
Important: To ensure stable operation it is essential that good PCB design practices are employed to minimize
ground impedance and keep input inductance low. If these conditions cannot be met, or if long leads are used to
connect the battery or other power source to the LP3990, then it is recommended that the input capacitor is
increased. Also, tantalum capacitors can suffer catastrophic failures due to surge current when connected to a
low-impedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at the
input, it must be guaranteed by the manufacturer to have a surge current rating sufficient for the application.
There are no requirements for the ESR (Equivalent Series Resistance) on the input capacitor, but tolerance and
temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain
approximately 1.0µF over the entire operating temperature range.
OUTPUT CAPACITOR
The LP3990 is designed specifically to work with very small ceramic output capacitors. A 1.0µF ceramic
capacitor (temperature types Z5U, Y5V or X7R) with ESR between 5mΩ to 500mΩ, is suitable in the LP3990
application circuit.
For this device the output capacitor should be connected between the VOUT pin and ground.
It is also possible to use tantalum or film capacitors at the device output, COUT (or VOUT), but these are not as
attractive for reasons of size and cost (see CAPACITOR CHARACTERISTICS).
The output capacitor must meet the requirement for the minimum value of capacitance and also have an ESR
value that is within the range 5mΩ to 500mΩ for stability.
NO-LOAD STABILITY
The LP3990 will remain stable and in regulation with no external load. This is an important consideration in some
circuits, for example CMOS RAM keep-alive applications.
CAPACITOR CHARACTERISTICS
The LP3990 is designed to work with ceramic capacitors on the output to take advantage of the benefits they
offer. For capacitance values in the range of 0.47µF to 4.7µF, ceramic capacitors are the smallest, least
expensive and have the lowest ESR values, thus making them best for eliminating high frequency noise. The
ESR of a typical 1.0µF ceramic capacitor is in the range of 20mΩ to 40mΩ, which easily meets the ESR
requirement for stability for the LP3990.
For both input and output capacitors, careful interpretation of the capacitor specification is required to ensure
correct device operation. The capacitor value can change greatly, depending on the operating conditions and
capacitor type.
In particular, the output capacitor selection should take account of all the capacitor parameters, to ensure that the
specification is met within the application. The capacitance can vary with DC bias conditions as well as
temperature and frequency of operation. Capacitor values will also show some decrease over time due to aging.
The capacitor parameters are also dependant on the particular case size, with smaller sizes giving poorer
performance figures in general. As an example, Figure 1 shows a typical graph comparing different capacitor
case sizes in a Capacitance vs. DC Bias plot. As shown in the graph, increasing the DC Bias condition can result
10
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LP3990
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
in the capacitance value falling below the minimum value given in the recommended capacitor specifications
table (0.7µF in this case). Note that the graph shows the capacitance out of spec for the 0402 case size
capacitor at higher bias voltages. It is therefore recommended that the capacitor manufacturers’ specifications for
the nominal value capacitor are consulted for all conditions, as some capacitor sizes (e.g. 0402) may not be
suitable in the actual application.
0603, 10V, X5R
100%
80%
60%
0402, 6.3V, X5R
40%_
20%
_
2.0
_
3.0
_
4.0
_
5.0
_
0
1.0
DC BIAS (V)
Figure 1. Graph Showing a Typical Variation in Capacitance vs DC Bias
The ceramic capacitor’s capacitance can vary with temperature. The capacitor type X7R, which operates over a
temperature range of -55°C to +125°C, will only vary the capacitance to within ±15%. The capacitor type X5R
has a similar tolerance over a reduced temperature range of -55°C to +85°C. Many large value ceramic
capacitors, larger than 1µF are manufactured with Z5U or Y5V temperature characteristics. Their capacitance
can drop by more than 50% as the temperature varies from 25°C to 85°C. Therefore X7R is recommended over
Z5U and Y5V in applications where the ambient temperature will change significantly above or below 25°C.
Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 0.47µF to 4.7µF range.
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic
capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum will increase about
2:1 as the temperature goes from 25°C down to -40°C, so some guard band must be allowed.
ENABLE CONTROL
The LP3990 features an active high Enable pin, VEN, which turns the device on when pulled high. When not
enabled the regulator output is off and the device typically consumes 2nA.
If the application does not require the Enable switching feature, the VEN pin should be tied to VIN to keep the
regulator output permanently on.
To ensure proper operation, the signal source used to drive the VEN input must be able to swing above and
below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH.
DSBGA MOUNTING
The DSBGA package requires specific mounting techniques, which are detailed in Application Note AN1112.
For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the
DSBGA device.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LP3990
LP3990
SNVS251I –MAY 2004–REVISED MAY 2013
www.ti.com
DSBGA LIGHT SENSITIVITY
Exposing the DSBGA device to direct light may affect the operation of the device. Light sources, such as halogen
lamps, can affect electrical performance, if placed in close proximity to the device.
Light with wavelengths in the infra-red portion of the spectrum is the most detrimental, and so, fluorescent
lighting used inside most buildings, has little or no effect on performance.
12
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LP3990
LP3990
www.ti.com
SNVS251I –MAY 2004–REVISED MAY 2013
REVISION HISTORY
Changes from Revision H (May 2013) to Revision I
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 12
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LP3990
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
LP3990MF-1.2/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
SCDB
LP3990MF-1.8
NRND
SOT-23
SOT-23
DBV
DBV
5
5
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 125
-40 to 125
SCFB
SCFB
LP3990MF-1.8/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3990MF-2.5
NRND
SOT-23
SOT-23
DBV
DBV
5
5
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 125
-40 to 125
SCJB
SCJB
LP3990MF-2.5/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3990MF-2.8/NOPB
LP3990MF-3.3/NOPB
LP3990MFX-1.2/NOPB
LP3990MFX-1.8/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
5
5
5
5
1000
1000
3000
3000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
SCKB
SCLB
SCDB
SCFB
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
LP3990MFX-3.3
NRND
SOT-23
SOT-23
DBV
DBV
5
5
3000
3000
TBD
Call TI
CU SN
Call TI
-40 to 125
-40 to 125
SCLB
SCLB
LP3990MFX-3.3/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LP3990SD-1.2/NOPB
LP3990SD-1.5/NOPB
LP3990SD-1.8/NOPB
LP3990TL-0.8/NOPB
LP3990TL-1.2/NOPB
LP3990TL-1.35/NOPB
LP3990TL-1.5/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
WSON
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
NGG
NGG
NGG
YZR
YZR
YZR
YZR
6
6
6
4
4
4
4
1000
1000
1000
250
Green (RoHS
& no Sb/Br)
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
L086B
L087B
L088B
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
CU SN
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
SNAGCU
SNAGCU
250
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
LP3990TL-1.8/NOPB
LP3990TL-2.5/NOPB
LP3990TL-2.8/NOPB
LP3990TLX-0.8/NOPB
LP3990TLX-1.2/NOPB
LP3990TLX-1.35/NOPB
LP3990TLX-1.5/NOPB
LP3990TLX-1.8/NOPB
LP3990TLX-2.5/NOPB
LP3990TLX-2.8/NOPB
ACTIVE
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YZR
4
4
4
4
4
4
4
4
4
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
250
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
3000
3000
3000
3000
3000
3000
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP3990MF-1.2/NOPB
LP3990MF-1.8
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
NGG
NGG
NGG
YZR
YZR
YZR
YZR
5
5
5
5
5
5
5
5
5
5
5
6
6
6
4
4
4
4
1000
1000
1000
1000
1000
1000
1000
3000
3000
3000
3000
1000
1000
1000
250
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
12.4
12.4
12.4
8.4
8.4
8.4
8.4
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.3
3.3
3.3
1.09
1.09
1.09
1.09
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.3
3.3
3.3
1.35
1.35
1.35
1.35
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.0
1.0
1.0
0.76
0.76
0.76
0.76
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q1
Q1
Q1
Q1
Q1
Q1
Q1
LP3990MF-1.8/NOPB
LP3990MF-2.5
LP3990MF-2.5/NOPB
LP3990MF-2.8/NOPB
LP3990MF-3.3/NOPB
LP3990MFX-1.2/NOPB SOT-23
LP3990MFX-1.8/NOPB SOT-23
LP3990MFX-3.3
SOT-23
LP3990MFX-3.3/NOPB SOT-23
LP3990SD-1.2/NOPB
LP3990SD-1.5/NOPB
LP3990SD-1.8/NOPB
LP3990TL-0.8/NOPB
LP3990TL-1.2/NOPB
LP3990TL-1.35/NOPB
LP3990TL-1.5/NOPB
WSON
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
250
250
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP3990TL-1.8/NOPB
LP3990TL-2.5/NOPB
LP3990TL-2.8/NOPB
LP3990TLX-0.8/NOPB
LP3990TLX-1.2/NOPB
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
4
4
4
4
4
4
4
4
4
4
250
250
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
1.09
1.09
1.09
1.09
1.09
1.09
1.09
1.09
1.09
1.09
1.35
1.35
1.35
1.35
1.35
1.35
1.35
1.35
1.35
1.35
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
250
3000
3000
3000
3000
3000
3000
3000
LP3990TLX-1.35/NOPB DSBGA
LP3990TLX-1.5/NOPB
LP3990TLX-1.8/NOPB
LP3990TLX-2.5/NOPB
LP3990TLX-2.8/NOPB
DSBGA
DSBGA
DSBGA
DSBGA
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LP3990MF-1.2/NOPB
LP3990MF-1.8
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
DBV
5
5
5
5
5
5
5
1000
1000
1000
1000
1000
1000
1000
210.0
210.0
210.0
210.0
210.0
210.0
210.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LP3990MF-1.8/NOPB
LP3990MF-2.5
LP3990MF-2.5/NOPB
LP3990MF-2.8/NOPB
LP3990MF-3.3/NOPB
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LP3990MFX-1.2/NOPB
LP3990MFX-1.8/NOPB
LP3990MFX-3.3
SOT-23
SOT-23
SOT-23
SOT-23
WSON
DBV
DBV
DBV
DBV
NGG
NGG
NGG
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
5
5
5
5
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
3000
3000
3000
3000
1000
1000
1000
250
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LP3990MFX-3.3/NOPB
LP3990SD-1.2/NOPB
LP3990SD-1.5/NOPB
LP3990SD-1.8/NOPB
LP3990TL-0.8/NOPB
LP3990TL-1.2/NOPB
LP3990TL-1.35/NOPB
LP3990TL-1.5/NOPB
LP3990TL-1.8/NOPB
LP3990TL-2.5/NOPB
LP3990TL-2.8/NOPB
LP3990TLX-0.8/NOPB
LP3990TLX-1.2/NOPB
LP3990TLX-1.35/NOPB
LP3990TLX-1.5/NOPB
LP3990TLX-1.8/NOPB
LP3990TLX-2.5/NOPB
LP3990TLX-2.8/NOPB
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
250
250
250
250
250
250
3000
3000
3000
3000
3000
3000
3000
Pack Materials-Page 3
MECHANICAL DATA
NGG0006A
SDE06A (Rev A)
www.ti.com
MECHANICAL DATA
YZR0004
D
0.600±0.075
E
TLA04XXX (Rev D)
D: Max = 1.324 mm, Min =1.263 mm
E: Max = 1.045 mm, Min =0.984 mm
4215042/A
12/12
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
LP3990MF-2.8/NOPB
IC VREG 2.8 V FIXED POSITIVE REGULATOR, PDSO5, ROHS COMPLIANT, SOT-23, 5 PIN, Fixed Positive Single Output Standard Regulator
NSC
LP3990MF-3.3/NOPB
IC VREG 3.3 V FIXED POSITIVE REGULATOR, PDSO5, ROHS COMPLIANT, SOT-23, 5 PIN, Fixed Positive Single Output Standard Regulator
NSC
©2020 ICPDF网 联系我们和版权申明