LP3991TL-1.8/NOPB [TI]
具有使能功能的 300mA、低压降稳压器 | YZR | 4;型号: | LP3991TL-1.8/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有使能功能的 300mA、低压降稳压器 | YZR | 4 稳压器 |
文件: | 总24页 (文件大小:699K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Reference
Design
Product
Folder
Tools &
Software
Technical
Documents
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
LP3991 300-mA LDO for Digital Applications
1 Features
3 Description
Operating from a minimum input voltage of 1.65 V,
1
•
•
•
•
•
•
•
•
•
•
Input Voltage From 1.65 V to 4 V
the LP3991 LDO has been designed to provide fixed
stable output voltages for load currents up to 300 mA.
This device is suitable where accurate low voltages
are required from low input voltage sources and is
therefore suitable for post regulation of switched
mode regulators. In such applications, significant
improvements in performance and EMI can be
realized, with little reduction in overall efficiency. The
LP3991 provides fixed outputs as low as 1.2 V from a
wide input range from 1.65 V to 4 V Using the enable
(EN) pin, the device may be controlled to provide a
shutdown state, in which negligible supply current is
drawn.
Output Voltage From 0.8 V to 3 V
1% Accuracy at Room Temperature
125-mV Dropout at 300-mA Load
50-µA Quiescent Current at 1-mA Load
Inrush Current Controlled to 600 mA
PSRR 65 dB at 1 kHz
100-µs Start-Up Time for 1.5-V VOUT
Stable With Ceramic Capacitors as Small as 0402
Thermal-Overload and Short-Circuit Protection
2 Applications
The LP3991 is designed to be stable with space-
saving ceramic capacitors as small as 0402 case
size.
•
•
•
Post DC-DC Regulator
Battery Operated Devices
Hand-Held Information Appliances
Performance is specified for a –40°C to +125°C
junction temperature range. For output voltage
options, contact your local Texas Instruments sales
office.
Device Information(1)
PART NUMBER
LP3991
PACKAGE
BODY SIZE (NOM)
DSBGA (4)
1.43 mm × 0.96 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
space
space
space
Typical Application Circuit
LP3991
IN
VIN
B2
OUT
1 mF
CIN
B1
4.7 mF
COUT
*
Load
VEN
EN
A2
GND
A1
* For VOUT = 1.3 V or less,
COUT may be reduced to 2.2 mF.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings ............................................................ 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information ................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Timing Requirements................................................ 6
6.7 Typical Characteristics.............................................. 7
Detailed Description .............................................. 9
7.1 Overview ................................................................... 9
7.2 Functional Block Diagram ......................................... 9
7.3 Feature Description................................................... 9
7.4 Device Functional Modes........................................ 10
8
Application and Implementation ........................ 11
8.1 Application Information............................................ 11
8.2 Typical Application ................................................. 11
Power Supply Recommendations...................... 16
9
10 Layout................................................................... 16
10.1 Layout Guidelines ................................................. 16
10.2 Layout Example .................................................... 16
10.3 DSBGA Mounting.................................................. 17
10.4 DSBGA Light Sensitivity ....................................... 17
11 Device and Documentation Support ................. 18
11.1 Documentation Support ........................................ 18
11.2 Receiving Notification of Documentation Updates 18
11.3 Community Resources.......................................... 18
11.4 Trademarks........................................................... 18
11.5 Electrostatic Discharge Caution............................ 18
11.6 Glossary................................................................ 18
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 18
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision I (August 2015) to Revision J
Page
•
•
•
•
•
•
Changed "Linear Voltage Regulator" to "LDO" in title............................................................................................................ 1
Changed "regulator" to "LDO" in Description ......................................................................................................................... 1
Changed Body Size dimensions from (MAX) to (NOM) in Device Information ..................................................................... 1
Added footnote 2 for Thermal Information ............................................................................................................................. 4
Added Power Dissipation and Estimating Junction Temperature subsections .................................................................... 14
Added Receiving Notification of Documentation Updates ................................................................................................... 18
Changes from Revision H (May 2013) to Revision I
Page
•
Added Device Information and Pin Configuration and Functions sections, ESD Rating table, Feature Description,
Device Functional Modes, Application and Implementation, Power Supply Recommendations, Layout, Device and
Documentation Support , and Mechanical, Packaging, and Orderable Information sections ................................................ 1
Changed pin names to TI nomenclature; added icon for Reference Design to Top Navigators ........................................... 1
Changed Output voltage range from "1.2 V to 2.8 V" to "0.8 V to 3 V" due to new options available to buy ....................... 1
Deleted Lead temp spec from Abs Max table; this info is in POA ........................................................................................ 4
Added updated thermal values .............................................................................................................................................. 4
Changed values in Table 1 based on updated thermal values ............................................................................................ 10
•
•
•
•
•
Changes from Revision G (May 2013) to Revision H
Page
•
Changed layout of National Data Sheet to TI format ........................................................................................................... 10
2
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
5 Pin Configuration and Functions
YZR Package
4-Pin Thin DSBGA, Large Bump
IN
B2
EN
A2
IN
B2
EN
A2
A1
GND
B1
OUT
B1
OUT
A1
GND
Top View
Bottom View
Pin Functions
PIN
I/O
DESCRIPTION
NUMBER
NAME
A1
GND
—
Common ground. Connect to pad.
Enable Input; enables the regulator when ≥ 0.95 V.
Disables the regulator when ≤ 0.4 V.
A2
EN
I
Enable input has an internal 1.2-MΩ pulldown resistor to GND.
Voltage output. A low-ESR ceramic capacitor must be connected from this pin to GND (see
Application and Implementation). Connect this output to the load circuit.
B1
B2
OUT
IN
O
I
Voltage supply input. A 1-µF capacitor must be connected from this pin to GND.
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
MIN
–0.3
–0.3
MAX
6.5
UNIT
V
IN, OUT pins, voltage to GND
EN pin, voltage to GND
(VIN + 0.3) < 6.5
150
V
Junction temperature
°C
Continuous power dissipation(4)
Internally Limited
150
Storage temperature, Tstg
–65
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the potential at the GND pin.
(3) If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) Internal thermal shutdown circuitry protects the device from permanent damage.
6.2 ESD Ratings
VALUE
±2000
±200
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
Electrostatic
discharge
V(ESD)
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
4
UNIT
V
Input voltage
1.65
Recommended load current
Junction temperature
300
125
85
mA
°C
–40
–40
(1)
Ambient temperature, TA
°C
(1) The maximum ambient temperature (TA-MAX) is a suggested value dependant on the maximum operating junction temperature (TJ-MAX-
OP) = 125°C); the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of
the part / package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX).
6.4 Thermal Information
LP3991
THERMAL METRIC(1)
YZR (DSBGA)
4 PINS
189.7
UNIT
(2)
RθJA
Junction-to-ambient thermal resistance, High K
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
ψJT
0.5
112.9
Junction-to-top characterization parameter
Junction-to-board characterization parameter
8.7
ψJB
112.8
(1) For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics.
(2) Thermal resistance value RθJA is based on the EIA/JEDEC High-K printed circuit board defined by: JESD51-7 - High Effective Thermal
Conductivity Test Board for Leaded Surface Mount Packages.
4
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
6.5 Electrical Characteristics
Unless otherwise noted, VEN = 950 mV, VIN = VOUT + 0.5 V, or 1.8 V, whichever is higher, CIN = 1 µF, COUT = 4.7 µF, IOUT
=
1 mA. Typical values and limits apply for TA = 25°C. Minimum and maximum limits apply over the full junction temperature
(1)
range for operation, −40°C to +125°C, unless otherwise specified.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
3.6
UNIT
See(2)
See(3)(4)(5)
1.65
VIN
Input voltage
V
4
TJ = 25°C
–1%
–3%
1%
3%
2.5%
VIN = VIN(NOM) to 3.6 V
ILOAD = 1 to 300 mA
Output voltage tolerance
TJ = –25°C to 85°C
–2.5%
ΔVOUT
VIN = VOUT(NOM) 0.5 V to 3.6 V,
IOUT = 1 mA, 0.8 V ≤ VOUT ≤ 2.8 V
Line regulation error
Load regulation error
0.05
1
%/V
IOUT = 1 mA to 300 mA
10
55
60 µV/mA
90
IOUT = 150 mA
1.8 V ≤ VOUT ≤ 2.5 V
IOUT = 300 mA
IOUT = 150 mA
IOUT = 300 mA
110
40
180
VDO
Dropout voltage(6)
mV
80
VOUT > 2.5 V
75
160
ILOAD
Minimum load current
Quiescent current
See(7)
0
mA
µA
VEN = 950 mV, IOUT = 0 mA
VEN = 950 mV, IOUT = 300 mA
VEN = 0.4 V
50
120
100
225
1
IQ
0.001
550
ISC
Short-circuit current limit
VIN = 3.6 V(8)
900
mA
mA
dB
IOUT
PSRR
Maximum output current
Power Supply Rejection Ratio(9)
300
ƒ = 1kHz, IOUT = 1 mA to 300 mA
65
BW = 10 Hz to 100 kHz,
VIN = 4.2 V, COUT = 4.7 µF
en
Output noise voltage(9)
280
µVRMS
°C
Temperature
Hysteresis
160
20
TSHUTDOWN Thermal shutdown
ENABLE CONTROL CHARACTERISTICS
VEN = 0 V, VIN = 3.6 V
VEN = VIN = 3.6 V
0.001
3
(10)
IEN
Maximum input current at VEN input
µA
5.5
0.4
VIL
VIH
Low input threshold
High input threshold
VIN = 1.65 V to 3.6 V
VIN = 1.65 V to 3.6 V
V
V
0.95
(1) All limits are ensured. All electrical characteristics having room-temperature limits are tested during production at TJ = 25°C or correlated
using Statistical Quality Control methods. Operation over the temperature specification is ensured by correlating the electrical
characteristics to process and temperature variations and applying statistical process control.
(2) All voltages are with respect to the potential at the GND pin.
(3) VIN(MIN) = VOUT(NOM) + 0.5 V or 1.65 V, whichever is greater. (See Figure 19 in DSBGA Light Sensitivity.)
(4) The device operates with input voltages up to 4 V. However special care must be taken in relation to thermal dissipation and the need to
derate the maximum allowable ambient temperature.
(5) The maximum ambient temperature (TA-MAX) is a suggested value dependant on the maximum operating junction temperature (TJ-MAX-
OP) = 125°C); the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of
the part / package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX).
(6) Dropout voltage is voltage difference between input and output at which the output voltage drops to 100 mV below its nominal value.
This parameter is only specified for output voltages above 1.8 V.
(7) The device maintains the regulated output voltage without a load.
(8) Short circuit current is measured with VOUT pulled to 0 V.
(9) This electrical specification is ensured by design.
(10) EN pin has an internal 1.2-MΩ (typical) resistor connected to GND.
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
Electrical Characteristics (continued)
Unless otherwise noted, VEN = 950 mV, VIN = VOUT + 0.5 V, or 1.8 V, whichever is higher, CIN = 1 µF, COUT = 4.7 µF, IOUT
=
1 mA. Typical values and limits apply for TA = 25°C. Minimum and maximum limits apply over the full junction temperature
range for operation, −40°C to +125°C, unless otherwise specified. (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMING CHARACTERISTICS
Trise = Tfall = 30 µs(9)
δVIN = 600 mV
mV
(pk - pk)
Line transient response |δVOUT
|
6
IOUT = 0 mA to 300 mA
IOUT = 1 mA to 300 mA
IOUT = 300 mA to 1 mA
IOUT = 0 mA to 200 mA
IOUT = 1 mA to 200 mA
IOUT = 200 mA to 1 mA
IOUT = 0 mA to 150 mA
IOUT = 1 mA to 150 mA
IOUT = 150 mA to 1 mA
140
110
80
110
80
Transient
Response Load transient response |δVOUT
|
Trise = Tfall = 1 µs(9)
mV
60
100
70
50
Overshoot on start-up
0%
600
2%
IIR
OUTPUT CAPACITANCE
In-rush current(9)
1000
mA
V
OUT ≥ 1.5 V
2
1.6
5
4.7
2.2
Capacitance(11)
ESR
µF
COUT
Output capacitor
VOUT < 1.5 V(12)
500
mΩ
(11) The capacitor tolerance must be 30% or better over temperature. The full operating conditions for the application must be considered
when selecting a suitable capacitor to ensure that the minimum value of capacitance is always met. Recommended capacitor type is
X7R or X5R. (See External Capacitors in Detailed Design Procedure.)
(12) On lower voltage options, 2.2-µF output capacitor may be used but some degradation in load transient (10 -15%) can be expected,
compared to a 4.7-µF capacitor.
6.6 Timing Requirements
MIN
NOM
MAX
UNIT
Turnon time(1) To 95% Level
VIN(MIN) to 3.6 V, VOUT ≤ 2 V
100
tON
µs
Turnon time(1) To 95% Level
VIN(MIN) to 3.6 V, VOUT ≥ 2 V
140
(1) This electrical specification is ensured by design.
6
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
6.7 Typical Characteristics
Unless otherwise specified, CIN = 1 µF ceramic, COUT = 4.7 µF ceramic, VIN = VOUT(NOM) + 0.5 V or 1.8 V, whichever is greater,
TA = 25°C, VOUT(NOM) = 1.5 V, EN pin is tied to VIN.
Figure 1. Output Voltage Change vs Temperature
Figure 2. Output Voltage vs Minimum Input Voltage
Figure 4. Ground Current vs VIN. ILOAD = 1mA
Figure 3. Ground Current vs Load Current
Figure 6. Dropout Voltage vs Output Voltage
Figure 5. Dropout Voltage
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, CIN = 1 µF ceramic, COUT = 4.7 µF ceramic, VIN = VOUT(NOM) + 0.5 V or 1.8 V, whichever is greater,
TA = 25°C, VOUT(NOM) = 1.5 V, EN pin is tied to VIN.
Figure 8. Short Circuit Current
Figure 7. Enable Characteristics
Figure 9. Power Supply Rejection Ratio
Figure 10. Power Supply Rejection Ratio
Figure 11. Noise Density
8
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
7 Detailed Description
7.1 Overview
The LP3991 device is a monolithic integrated low-dropout voltage regulator with a low input operating voltage
tolerance. Key protection circuits, including output current limitation and thermal shutdown, are integrated in the
device. Using the EN pin, the device may be controlled to provide a shutdown state, in which negligible supply
current is drawn. The LP3991 is designed to be stable with space-saving ceramic capacitors as small as 0402
case size.
7.2 Functional Block Diagram
IN
OUT
ON
OFF
EN
1.2 Mꢀ
GND
LP3991
7.3 Feature Description
7.3.1 Post-Buck Regulator
Linear post-regulation can be an effective way to reduce ripple and switching noise from DC-DC convertors while
still maintaining a reasonably high overall efficiency.
The LP3991 is particularly suitable for this role due to its low input voltage requirements. In addition, there is
often no need for a separate input capacitor for the LP3991 as it can share the output cap of the DC-DC
convertor.
Care of PCB layouts involving switching regulators is paramount. In particular, the ground paths for the LDO
must be routed separately from the switcher ground and star connected close to the battery. Routing of the
switch pin of the DC-DC convertor must be kept short to minimize radiated EMI. A low pass filter such as a ferrite
bead or common mode choke on the battery input leads can further reduce radiated EMI.
Figure 19 shows a typical example using an LM3673, 350-mA DC-DC buck regulator with a nominal output of
1.8 V and a 1.5-V LP3991 device. The overall efficiency is greater than 70% over the full Li-Ion battery voltage
range. Maximum efficiency is achieved by minimizing the difference between VIN and VOUT of the LP3991 device.
The LP3991-1.5 remains in regulation down to an input voltage of 1.65 V; thus, in this case, a 1.8-V buck with
5% tolerance is adequate for all conditions of temperature and load.
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
Feature Description (continued)
7.3.2 Maximum Supply Voltage and Thermal Considerations
Maximum recommended input voltage is 3.6 V. The device may be operated at 4-V VIN if proper care is given to
the board design in regard to thermal dissipation. As a guide, refer to Table 1 for ambient temperature at two
input voltages and two load currents for the example board types.
Table 1. Example Board Ambient Temperatures
RθJA
VIN
VOUT
IOUT
PD
AMBIENT TEMPERATURE
160 mA
250 mA
160 mA
250 mA
160 mA
250 mA
160 mA
250 mA
0.13 W
0.20 W
0.19 W
0.30 W
0.13 W
0.20 W
0.19 W
0.30 W
100ºC
87ºC
89ºC
68ºC
104ºC
93ºC
94ºC
77ºC
3.6 V
2.8 V
189ºC/W
4 V
3.6 V
4 V
2.8 V
2.8 V
2.8 V
160ºC/W
7.4 Device Functional Modes
7.4.1 Enable Control
The LP3991 features an active high enable (EN) pin, which turns the device on when pulled high. When not
enabled the regulator output is off and the device typically consumes 2 nA.
If the application does not require the enable switching feature, the EN pin must be tied to VIN to keep the
regulator output permanently on.
To ensure proper operation, the signal source used to drive the EN input must be able to swing above and below
the specified turnon/off voltage thresholds listed in Typical Characteristics under VIL and VIH.
10
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP3991 can provide 300-mA output current with 1.65-V to 4-V input. It is stable with a 2.2-μF or 4.7-µF
ceramic output capacitor. An optional external bypass capacitor reduces the output noise without slowing down
the load transient response. Typical output noise is 280 μVRMS at frequencies from 10 Hz to 100 kHz. Typical
power supply rejection is 65 dB at 1 kHz.
8.2 Typical Application
LP3991
IN
VIN
B2
A2
OUT
1 mF
CIN
B1
4.7 mF
COUT
*
Load
VEN
EN
GND
A1
* For VOUT = 1.3 V or less,
COUT may be reduced to 2.2 mF.
Figure 12. LP3991 Typical Application
8.2.1 Design Requirements
For typical linear voltage regulator applications, use the parameters listed in Table 2.
Table 2. Design Parameters
DESIGN PARAMETER
Input voltage
EXAMPLE VALUE
1.65 V to 4 V
1.2 V to 2.8 V
300 mA (maximum)
280 μVRMS
Output voltage
Output current
RMS noise, 10 Hz to100 kHz
PSRR at 1 kHz
65 dB
8.2.2 Detailed Design Procedure
8.2.2.1 External Capacitors
In common with most regulators, the LP3991 requires external capacitors for regulator stability. The LP3991 is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
8.2.2.2 Input Capacitor
An input capacitor is required for stability. It is recommended that a 1-µF capacitor be connected between the
LP3991 IN pin and ground (this capacitance value may be increased without limit).
This capacitor must be located a distance of not more than 1 cm from the IN pin and returned to a clean analog
ground. Any good-quality ceramic, tantalum, or film capacitor may be used at the input.
NOTE
Tantalum capacitors can suffer catastrophic failures due to surge current when connected
to a low-impedance source of power (like a battery or a very large capacitor). If a tantalum
capacitor is used at the input, a surge current rating sufficient for the application must be
ensured by the manufacturer.
There are no requirements for the equivalent series resistance (ESR) on the input capacitor, but tolerance,
temperature, and voltage coefficients must be considered when selecting the capacitor to ensure the capacitance
remains ≊ 1 µF over the entire operating temperature range.
8.2.2.3 Output Capacitor
Correct selection of the output capacitor is critical to ensure stable operation in the intended application.
The output capacitor must meet all the requirements specified in the recommended capacitor table over all
conditions in the application. these conditions include DC bias, frequency and temperature. Unstable operation
results if the capacitance drops below the minimum specified value.
The LP3991 is designed specifically to work with very small ceramic output capacitors. For voltage options of 1.5
V and higher, A 4.7-µF ceramic capacitor (dielectric type X7R or X5R) with an ESR between 5 mΩ to 500 mΩ, is
suitable in the LP3991 application circuit. However, on lower VOUT options a 2.2-µF may be employed with only a
small increase in load transient.
Other ceramic types such as Y5V and Z5U are less suitable owing to their inferior temperature characteristics.
(See Capacitor Characteristics.)
It is also recommended that the output capacitor is placed within 1 cm of the OUT pin and returned to a clean,
low impedance, ground connection.
It is possible to use tantalum or film capacitors at the device output, VOUT, but these are not as attractive for
reasons of size and cost. (See Capacitor Characteristics.)
8.2.2.4 No-Load Stability
The LP3991 remains stable and in regulation with no external load. This is an important consideration in some
circuits, for example CMOS RAM keep-alive applications.
8.2.2.5 Capacitor Characteristics
The LP3991 is designed to work with ceramic capacitors on the input and output to take advantage of the
benefits they offer. For capacitance values around 4.7 µF, ceramic capacitors give the circuit designer the best
design options in terms of low cost and minimal area.
For both input and output capacitors, careful interpretation of the capacitor specification is required to ensure
correct device operation. The capacitor value can change greatly dependant on the conditions of operation and
capacitor type.
In particular, to ensure stability, the output capacitor selection must take account of all the capacitor parameters,
to ensure that the specification is met within the application. Capacitance value can vary with DC bias conditions
as well as temperature and frequency of operation. Capacitor values also show some decrease over time due to
aging. The capacitor parameters are also dependant on the particular case size with smaller sizes giving poorer
performance figures in general.
12
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
0603, 10V, X5R
100
80
60
40
20
0402, 6.3V, X5R
0
1.0
2.0
3.0
4.0
5.0
DC BIAS (V)
Figure 13. Effect of DC Bias on Capacitance Value
As an example Figure 13 shows a typical graph showing a comparison of capacitor case sizes in a capacitance
vs. DC Bias plot. As shown in Figure 13, as a result of the DC Bias condition, the capacitance value may drop
below the minimum capacitance value given in the recommended capacitor table. Note that Figure 13 shows the
capacitance out of spec for the 0402 case size capacitor at higher bias voltages. TI therefore recommends that
the capacitor manufacturers' specifications for the nominal value capacitor are consulted for all conditions as
some capacitor sizes (for example, 0402) may not be suitable in the actual application. Ceramic capacitors have
the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of a typical 4.7-µF
ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which easily meets the ESR requirement for stability for the
LP3991. The temperature performance of ceramic capacitors varies by type. Capacitor type X7R is specified with
a tolerance of ±15% over the temperature range –55°C to +125°C. The X5R has a similar tolerance over the
reduced temperature range of –55°C to +85°C. Some large value ceramic capacitors (4.7 µF) are manufactured
with Z5U or Y5V temperature characteristics, which can result in the capacitance dropping by more than 50% as
the temperature varies from 25°C to +85°C. Therefore, X7R or X5R types are recommended in applications
where the temperature changes significantly above or below 25°C.
Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 1-µF to 4.7-µF range. Another
important consideration is that tantalum capacitors have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum capacitor with an ESR value within the stable range, it
would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the
same ESR value. The ESR of a typical tantalum increases about 2:1 as the temperature goes from 25°C down to
–40°C, so some guard band must be allowed.
8.2.2.6 Power Dissipation
Knowing the device power dissipation and proper sizing of the thermal plane connected to the tab or pad is
critical to ensuring reliable operation. Device power dissipation depends on input voltage, output voltage, and
load conditions and can be calculated with Equation 1.
PD(MAX) = (VIN(MAX) – VOUT) × IOUT
(1)
Power dissipation can be minimized, and greater efficiency can be achieved, by using the lowest available
voltage drop option that would still be greater than the dropout voltage (VDO). However, keep in mind that higher
voltage drops result in better dynamic (that is, PSRR and transient) performance.
On the LP3991 DSBGA (YZR) package, the primary conduction path for heat is through the four bumps to the
PCB. The maximum allowable junction temperature (TJ(MAX)) determines maximum power dissipation allowed
(PD(MAX)) for the device package.
Power dissipation and junction temperature are most often related by the junction-to-ambient thermal resistance
(RθJA) of the combined PCB and device package and the temperature of the ambient air (TA), according to
Equation 2 or Equation 3:
TJ(MAX) = TA(MAX) + ( RθJA × PD(MAX)
PD(MAX) = (TJ(MAX) – TA(MAX)) / RθJA
)
(2)
(3)
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
Unfortunately, this RθJA is highly dependent on the heat-spreading capability of the particular PCB design, and
therefore varies according to the total copper area, copper weight, and location of the planes. The RθJA recorded
in Thermal Information is determined by the specific EIA/JEDEC JESD51-7 standard for PCB and copper-
spreading area, and is to be used only as a relative measure of package thermal performance. For a well-
designed thermal layout, RθJA is actually the sum of the package junction-to-board thermal resistance (RθJB) plus
the thermal resistance contribution by the PCB copper area acting as a heat sink.
8.2.2.7 Estimating Junction Temperature
The EIA/JEDEC standard recommends the use of psi (Ψ) thermal characteristics to estimate the junction
temperatures of surface mount devices on a typical PCB board application. These characteristics are not true
thermal resistance values, but rather package specific thermal characteristics that offer practical and relative
means of estimating junction temperatures. These psi metrics are determined to be significantly independent of
copper-spreading area. The key thermal characteristics (ΨJT and ΨJB) are given in Thermal Information and are
used in accordance with Equation 4 or Equation 5.
TJ(MAX) = TTOP + (ΨJT × PD(MAX)
)
where
•
•
PD(MAX) is explained in Equation 1
TTOP is the temperature measured at the center-top of the device package.
(4)
TJ(MAX) = TBOARD + (ΨJB × PD(MAX)
)
where
•
•
PD(MAX) is explained in Equation 1
TBOARD is the PCB surface temperature measured 1 mm from the device package and centered on the
package edge.
(5)
For more information about the thermal characteristics ΨJT and ΨJB, see Semiconductor and IC Package
Thermal Metrics (SPRA953); for more information about measuring TTOP and TBOARD, see Using New Thermal
Metrics (SBVA025); and for more information about the EIA/JEDEC JESD51 PCB used for validating RθJA, see
the Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs (SZZA017). These
application notes are available at www.ti.com.
14
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
8.2.3 Application Curves
VOUT = 1.5 V
VOUT = 1.2 V
Figure 14. Load Transient
Figure 15. Load Transient
ILOAD = 1 mA
ILOAD = 300 mA
Figure 16. Line Transient
Figure 17. Line Transient
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
9 Power Supply Recommendations
The LP3991 is designed to operate from an input voltage supply range from 1.65 V to 4 V.
10 Layout
10.1 Layout Guidelines
The dynamic performance of the LP3991 is dependant on the layout of the PCB. PCB layout practices that are
adequate for typical LDOs may degrade the PSRR or transient performance of the LP3991.
Best performance is achieved by placing all of the components on the same side of the PCB as the LP3991, as
close as is practical to the LP3991 package. All component ground connections must be back to the LP3991
analog ground connection using as wide and as short of a copper trace as is practical.
Connections using long trace lengths, narrow trace widths, and connections through vias must be avoided.
These add parasitic inductances and resistance that results in inferior performance especially during transient
conditions.
A ground plane, either on the opposite side of a two-layer PCB, or embedded in a multi-layer PCB, is strongly
recommended. This ground plane serves two purposes:
1. Provides a circuit reference plane to assure accuracy, and
2. Provides a thermal plane to remove heat from the LP3991 through thermal vias under the package DAP.
10.2 Layout Example
LP3991TL
VIN
VOUT
B1
A1
B2
A2
COUT
CIN
Power Ground
VEN
Figure 18. LP3991 Example Layout
16
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
LP3991
www.ti.com
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
10.3 DSBGA Mounting
The DSBGA package requires specific mounting techniques which are detailed in AN-1112 DSBGA Wafer Level
Chip Scale Package. Referring to the section Surface Mount Technology (SMT) Assenbly Considerations, the
pad style that must be used with the 4-pin package is a NSMD (non-solder mask defined) type.
For best results during assembly, alignment ordinals on the PCB may be used to facilitate placement of the
DSBGA device.
10.4 DSBGA Light Sensitivity
Exposing the DSBGA device to direct sunlight may cause mis-operation of the device. Light sources such as
halogen lamps can affect the electrical performance if brought near to the device.
The wavelengths that have the most detrimental effect are reds and infra-reds, which means that the fluorescent
lighting used inside most buildings has little effect on performance.
Ferrite
Bead
2.2 mH
V
OUT
V
V
1.5V
IN
IN
1.8V
SW
FB
B2
B1
A1
B2
C1
4.7 mF
C2
10 mF
LM3673TL-
1.8
LP3991TL-
1.5
C4
4.7 mF
Li-Ion
2.7 œ 4.3V
GND
GND
A3
A1
C3
A2
C1
EN
DC/DC
EN
LDO
Figure 19. LP3991 Used as a Post DC-DC Regulator
Copyright © 2006–2016, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LP3991
LP3991
SNVS296J –DECEMBER 2006–REVISED JUNE 2016
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For additional information, see the following:
•
•
•
•
AN-1112 DSBGA Wafer Level Chip Scale Package (SNVA009)
Semiconductor and IC Package Thermal Metrics (SPRA953)
Using New Thermal Metrics (SBVA025)
Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs (SZZA017)
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 2006–2016, Texas Instruments Incorporated
Product Folder Links: LP3991
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LP3991TL-1.2/NOPB
LP3991TL-1.3/NOPB
LP3991TL-1.5/NOPB
LP3991TL-1.7/NOPB
LP3991TL-1.8/NOPB
LP3991TL-2.0/NOPB
LP3991TL-2.5/NOPB
LP3991TL-2.8/NOPB
LP3991TL-3.0/NOPB
LP3991TLX-1.2/NOPB
LP3991TLX-1.3/NOPB
LP3991TLX-1.5/NOPB
LP3991TLX-1.8/NOPB
LP3991TLX-2.5/NOPB
LP3991TLX-2.8/NOPB
LP3991TLX-3.0/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
250
250
250
250
250
250
250
250
250
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
-40 to 125
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
-40 to 125
-40 to 125
-40 to 125
-40 to 125
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Nov-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP3991TL-1.2/NOPB
LP3991TL-1.3/NOPB
LP3991TL-1.5/NOPB
LP3991TL-1.7/NOPB
LP3991TL-1.8/NOPB
LP3991TL-2.0/NOPB
LP3991TL-2.5/NOPB
LP3991TL-2.8/NOPB
LP3991TL-3.0/NOPB
LP3991TLX-1.2/NOPB
LP3991TLX-1.3/NOPB
LP3991TLX-1.5/NOPB
LP3991TLX-1.8/NOPB
LP3991TLX-2.5/NOPB
LP3991TLX-2.8/NOPB
LP3991TLX-3.0/NOPB
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
250
250
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.04
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
1.55
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
250
250
250
250
250
250
250
3000
3000
3000
3000
3000
3000
3000
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Nov-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LP3991TL-1.2/NOPB
LP3991TL-1.3/NOPB
LP3991TL-1.5/NOPB
LP3991TL-1.7/NOPB
LP3991TL-1.8/NOPB
LP3991TL-2.0/NOPB
LP3991TL-2.5/NOPB
LP3991TL-2.8/NOPB
LP3991TL-3.0/NOPB
LP3991TLX-1.2/NOPB
LP3991TLX-1.3/NOPB
LP3991TLX-1.5/NOPB
LP3991TLX-1.8/NOPB
LP3991TLX-2.5/NOPB
LP3991TLX-2.8/NOPB
LP3991TLX-3.0/NOPB
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
YZR
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
250
250
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
208.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
250
250
250
250
250
250
250
3000
3000
3000
3000
3000
3000
3000
Pack Materials-Page 2
MECHANICAL DATA
YZR0004
D
0.600±0.075
E
TLA04XXX (Rev D)
D: Max = 1.46 mm, Min = 1.4 mm
E: Max = 0.99 mm, Min = 0.93 mm
4215042/A
12/12
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
LP3991TL-2.5/NOPB
IC VREG 2.5 V FIXED POSITIVE REGULATOR, PBGA4, 0.963 X 1.446 MM, LEAD FREE, MICRO SMD-4, Fixed Positive Single Output Standard Regulator
NSC
LP3991TL-3.0
IC VREG FIXED POSITIVE LDO REGULATOR, PBGA4, 0.963 X 1.446 MM, LEAD FREE, MICRO SMD-4, Fixed Positive Single Output LDO Regulator
NSC
©2020 ICPDF网 联系我们和版权申明