MAX3222E [TI]
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 【15-kV ESD PROTECTION; 3V至5.5V多通道RS - 232线路驱动器/接收器【 15 kV ESD保护
| 型号： | MAX3222E |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 【15-kV ESD PROTECTION |
| 文件： | 总16页 (文件大小：311K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
FEATURES
DB, DW, OR PW PACKAGE
•
ESD Protection for RS-232 Bus Pins
(TOP VIEW)
– ±15-kV Human-Body Model (HBM)
EN
C1+
1
2
3
4
5
6
7
8
9
10
20 PWRDOWN
– ±8-kV IEC61000-4-2, Contact Discharge
– ±15-kV IEC61000-4-2, Air-Gap Discharge
19
18
17
16
15
14
13
12
11
V
CC
V+
C1−
C2+
C2−
GND
DOUT1
RIN1
ROUT1
NC
•
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
•
•
•
•
•
•
•
Operates With 3-V to 5.5-V VCC Supply
Operates up to 500 kbit/s
V−
DOUT2
RIN2
ROUT2
DIN1
DIN2
NC
Two Drivers and Two Receivers
Low Standby Current . . . 1 µA Typ
External Capacitors . . . 4 × 0.1 µF
Accepts 5-V Logic Input With 3.3-V Supply
NC − No internal connection
Alternative High-Speed Pin-Compatible Device
(1 Mbit/s) for SNx5C3222E
RHL PACKAGE
(TOP VIEW)
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Notebooks
Laptops
Palmtop PCs
Hand-Held Equipment
24
1
2
23
22
21
20
19
18
17
16
15
14
C1+
NC
V+
C1–
C2+
C2–
V–
V
CC
3
NC
4
GND
DOUT1
RIN1
ROUT1
NC
DIN1
NC
DIN2
5
DESCRIPTION/ORDERING INFORMATION
6
7
The MAX3222E consists of two line drivers, two line
receivers, and a dual charge-pump circuit with ±15-kV
ESD protection pin to pin (serial-port connection pins,
including GND).
8
9
DOUT2
NC
RIN2
10
11
The device meets the requirements of TIA/EIA-232-F
and provides the electrical interface between an
asynchronous communication controller and the
serial-port connector. The charge pump and four
small external capacitors allow operation from a
single 3-V to 5.5-V supply. The device operates at
typical data signaling rates up to 500 kbit/s and a
maximum of 30-V/µs driver output slew rate.
12
13
NC − No internal connection
The MAX3222E can be placed in the power-down mode by setting the power-down (PWRDOWN) input low,
which draws only 1 µA from the power supply. When the device is powered down, the receivers remain active
while the drivers are placed in the high-impedance state. Also, during power down, the onboard charge pump is
disabled; V+ is lowered to VCC, and V– is raised toward GND. Receiver outputs also can be placed in the
high-impedance state by setting enable (EN) high.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2006, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
ORDERING INFORMATION
TA
PACKAGE(1)
ORDERABLE PART NUMBER
MAX3222ECDW
MAX3222ECDWR
MAX3222ECDB
TOP-SIDE MARKING
Tube of 25
SOIC – DW
SSOP – DB
TSSOP – PW
SOIC – DW
SSOP – DB
TSSOP – PW
MAX3222EC
Reel of 2000
Tube of 70
0°C to 70°C
MP222EC
MP222EC
MAX3222EI
MP222EI
Reel of 2000
Tube of 70
MAX3222ECDBR
MAX3222ECPW
MAX3222ECPWR
MAX3222EIDW
Reel of 2000
Tube of 25
Reel of 2000
Tube of 70
MAX3222EIDWR
MAX3222EIDB
–40°C to 85°C
Reel of 2000
Tube of 70
MAX3222EIDBR
MAX3222EIPW
MP222EI
Reel of 2000
MAX3222EIPWR
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
FUNCTION TABLES
XXX
EACH DRIVER(1)
INPUTS
PWRDOWN
OUTPUT
DOUT
DIN
X
L
H
H
Z
H
L
L
H
(1) H = high level, L = low level, X = irrelevant, Z = high impedance
EACH RECEIVER(1)
INPUTS
OUTPUT
ROUT
RIN
L
EN
L
H
L
H
L
X
H
L
Z
H
Open
(1) H = high level, L = low level, X = irrelevant,
Z = high impedance (off),
Open = input disconnected or connected driver off
2
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
LOGIC DIAGRAM (POSITIVE LOGIC)
13
17
8
DIN1
DOUT1
DOUT2
12
20
DIN2
Powerdown
PWRDOWN
1
EN
15
16
ROUT1
RIN1
RIN2
5 kW
10
9
ROUT2
5 kW
Pin numbers are for the DB, DW, and PW packages.
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.3
–0.3
0.3
MAX UNIT
VCC
V+
Supply voltage range(2)
Positive-output supply voltage range(2)
Negative-output supply voltage range(2)
6
V
V
V
V
7
–7
V–
V+ – V– Supply voltage difference(2)
13
Driver (EN, PWRDOWN)
Receiver
–0.3
–25
6
VI
Input voltage range
Output voltage range
V
V
25
Driver
–13.2
–0.3
13.2
VCC + 0.3
70
VO
Receiver
DB package
DW package
PW package
RHL package
58
θJA
Package thermal impedance(3)(4)
°C/W
83
TBD
150
150
TJ
Operating virtual junction temperature
Storage temperature range
°C
°C
Tstg
–65
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to network GND.
(3) Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
3
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
Recommended Operating Conditions(1)
See Figure 5
MIN NOM MAX UNIT
VCC = 3.3 V
3
4.5
2
3.3
5
3.6
5.5
Supply voltage
V
V
VCC = 5 V
VCC = 3.3 V
VCC = 5 V
VIH
Driver and control high-level input voltage
DIN, EN, PWRDOWN
2.4
VIL
VI
Driver and control low-level input voltage
Driver and control input voltage
Receiver input voltage
DIN, EN, PWRDOWN
DIN, EN, PWRDOWN
0.8
5.5
25
70
85
V
V
V
0
–25
0
VI
MAX3222EC
MAX3222EI
TA
Operating free-air temperature
°C
–40
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2–C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
Input leakage current (EN, PWRDOWN)
Supply current
TEST CONDITIONS
MIN
TYP(2)
±0.01
0.3
MAX
±1
UNIT
II
µA
mA
µA
No load, PWRDOWN at VCC
No load, PWRDOWN at GND
1
ICC
Supply current (powered off)
1
10
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2–C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
4
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
DRIVER SECTION
abc
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
TEST CONDITIONS
MIN TYP(2)
MAX UNIT
VOH
VOL
IIH
High-level output voltage
Low-level output voltage
High-level input current
Low-level input current
DOUT at RL = 3 kΩ to GND,
DIN = GND
DIN = VCC
5
5.4
–5.4
V
V
DOUT at RL = 3 kΩ to GND,
VI = VCC
–5
±0.01
±0.01
±1
±1
µA
µA
IIL
VI at GND
VCC = 3.6 V
IOS
ro
Short-circuit output current(3)
Output resistance
VO = 0 V
±35
±60
mA
VCC = 5.5 V
VCC, V+, and V– = 0 V,
VO = ±2 V
300
10M
Ω
VCC = 3 V to 3.6 V,
VO = ±12 V
±25
±25
IOZ
Output leakage current
PWRDOWN = GND
µA
VCC = 4.5 V to 5.5 V,
VO = ±10 V
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2–C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
TEST CONDITIONS
MIN
TYP(2)
MAX UNIT
CL = 1000 pF,
One DOUT switching,
RL = 3 kΩ,
See Figure 1
Maximum data rate
250
500
kbit/s
CL = 150 pF to 2500 pF,
See Figure 2
RL = 3 kΩ to 7 kΩ,
tsk(p)
Pulse skew(3)
300
ns
Slew rate,
transition region
(see Figure 1)
CL = 150 pF to 1000 pF
CL = 150 pF to 2500 pF
6
4
30
RL = 3 kΩ to 7 kΩ,
VCC = 3.3 V
SR(tr)
V/µs
30
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2–C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
5
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
RECEIVER SECTION
abc
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
High-level output voltage
TEST CONDITIONS
IOH = –1 mA
IOL = 1.6 mA
VCC = 3.3 V
MIN
TYP(2)
MAX UNIT
VOH
VOL
VCC – 0.6
VCC – 0.1
V
Low-level output voltage
0.4
2.4
2.4
V
1.5
1.8
VIT+
Positive-going input threshold voltage
V
VCC = 5 V
VCC = 3.3 V
0.6
0.8
1.2
VIT–
Negative-going input threshold voltage
V
VCC = 5 V
1.5
Vhys
IOZ
ri
Input hysteresis (VIT+ – VIT–
Output leakage current
Input resistance
)
0.3
V
EN = 1
±0.05
5
±10
µA
kΩ
VI = ±3 V to ±25 V
3
7
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2–C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Switching Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
CL = 150 pF, See Figure 3
TYP(2) UNIT
tPLH Propagation delay time, low- to high-level output
tPHL Propagation delay time, high- to low-level output
300
300
200
200
300
ns
ns
ns
ns
ns
CL = 150 pF, See Figure 3
CL = 150 pF, RL = 3 kΩ, See Figure 4
CL = 150 pF, RL = 3 kΩ, See Figure 4
See Figure 3
ten
Output enable time
Output disable time
tdis
tsk(p) Pulse skew(3)
(1) Test conditions are C1–C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2–C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
6
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
PARAMETER MEASUREMENT INFORMATION
3 V
Input
1.5 V
1.5 V
RS-232
Output
0 V
Generator
(see Note B)
50 Ω
C
L
t
R
L
t
TLH
THL
(see Note A)
3 V
PWRDOWN
V
V
OH
3 V
−3 V
3 V
−3 V
Output
OL
TEST CIRCUIT
VOLTAGE WAVEFORMS
6 V
or t
SR(tr) +
t
THL
TLH
A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns,
tf ≤ 10 ns.
Figure 1. Driver Slew Rate
3 V
0 V
Input
1.5 V
1.5 V
RS-232
Output
Generator
(see Note B)
50 Ω
C
L
t
t
PLH
PHL
R
L
(see Note A)
V
V
OH
3 V
PWRDOWN
50%
50%
Output
OL
TEST CIRCUIT
A. CL includes probe and jig capacitance.
VOLTAGE WAVEFORMS
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns,
tf ≤ 10 ns.
Figure 2. Driver Pulse Skew
EN
0 V
3 V
Input
1.5 V
1.5 V
−3 V
Output
Generator
(see Note B)
50 Ω
t
t
PLH
PHL
C
L
(see Note A)
V
V
OH
50%
50%
Output
OL
TEST CIRCUIT
A. CL includes probe and jig capacitance.
VOLTAGE WAVEFORMS
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 3. Receiver Propagation Delay Times
7
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
PARAMETER MEASUREMENT INFORMATION (continued)
3 V
V
CC
GND
Input
1.5 V
1.5 V
S1
0 V
R
L
t
t
PZH
PHZ
S1 at GND)
(S1 at GND)
3 V or 0 V
Output
V
OH
C
L
Output
50%
(see Note A)
EN
0.3 V
0.3 V
t
PLZ
Generator
(see Note B)
(S1 at V
)
CC
50 Ω
Output
50%
V
OL
t
PZL
(S1 at V )
CC
TEST CIRCUIT
A. CL includes probe and jig capacitance.
VOLTAGE WAVEFORMS
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 4. Receiver Enable and Disable Times
8
Submit Documentation Feedback
MAX3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS708–JANUARY 2006
APPLICATION INFORMATION
1
20
EN
Powerdown
PWRDOWN
2
19
18
V
C1+
V+
CC
+
−
C
BYPASS
= 0.1 µF
+
−
3
4
5
6
7
GND
C1
+
−
†
C3
17
16
DOUT1
RIN1
C1−
C2+
C2−
V−
5 kW
+
−
C2
C4
15
14
13
12
11
ROUT1
NC
−
+
8
9
DOUT2
DIN1
DIN2
NC
RIN2
5 kW
10
ROUT2
†
C3 can be connected to V or GND.
CC
NOTES: A. Resistor values shown are nominal.
B. NC − No internal connection
C. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be
connected as shown.
V
CC
vs CAPACITOR VALUES
V
C1
C2, C3, and C4
0.1 µF
CC
0.1 µF
0.047 µF
0.1 µF
3.3 V " 0.3 V
5 V " 0.5 V
3 V to 5.5 V
0.33 µF
0.47 µF
Figure 5. Typical Operating Circuit and Capacitor Values
9
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
PACKAGING INFORMATION
Orderable Device
MAX3222ECDB
MAX3222ECDBR
MAX3222ECDW
MAX3222ECDWR
MAX3222ECPW
MAX3222ECPWR
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SSOP
DB
20
20
20
20
20
20
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SSOP
SOIC
DB
DW
DW
PW
PW
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TSSOP
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MAX3222ECRHLR
MAX3222EIDB
PREVIEW
ACTIVE
QFN
RHL
DB
24
20
1000
TBD
Call TI
Call TI
SSOP
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MAX3222EIDBR
MAX3222EIDW
MAX3222EIDWR
MAX3222EIPW
MAX3222EIPWR
MAX3222EIRHLR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PREVIEW
SSOP
SOIC
DB
DW
DW
PW
PW
RHL
20
20
20
20
20
24
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TSSOP
QFN
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
1000
TBD
Call TI
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
M
0,15
15
0,25
0,09
5,60
5,00
8,20
7,40
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
0,10
2,00 MAX
0,05 MIN
PINS **
14
16
20
24
28
30
38
DIM
6,50
5,90
6,50
5,90
7,50
8,50
7,90
10,50
9,90
10,50 12,90
A MAX
A MIN
6,90
9,90
12,30
4040065 /E 12/01
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
M
0,10
0,65
14
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
8
14
16
20
24
28
DIM
3,10
2,90
5,10
4,90
5,10
4,90
6,60
6,40
7,90
9,80
9,60
A MAX
A MIN
7,70
4040064/F 01/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Low Power Wireless www.ti.com/lpw
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2006, Texas Instruments Incorporated
相关型号：
MAX3222E-MAX3246E
【15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM
MAX3222EAP
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232 Transceivers Using Four 0.1レF External Capacitors
MAXIM
MAX3222EC/D
【15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM
MAX3222EC/D+
±15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM
MAX3222ECAP+
±15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM
©2020 ICPDF网 联系我们和版权申明