OPA1013DN8 [TI]
Precision, Single-Supply DUAL OPERATIONAL AMPLIFIER;![OPA1013DN8](http://pdffile.icpdf.com/pdf2/p00274/img/icpdf/OPA1013DN8G4_1639907_icpdf.jpg)
型号: | OPA1013DN8 |
厂家: | ![]() |
描述: | Precision, Single-Supply DUAL OPERATIONAL AMPLIFIER 放大器 光电二极管 |
文件: | 总10页 (文件大小:151K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
®
OPA1013
Precision, Single-Supply
DUAL OPERATIONAL AMPLIFIER
FEATURES
APPLICATIONS
● SINGLE POWER SUPPLY OPERATION
● INPUT VOLTAGE RANGE TO GROUND
● OUTPUT SWINGS NEAR GROUND
● LOW QUIESCENT CURRENT: 550µA max
● LOW VOS: 300µV max
● PRECISION INSTRUMENTATION
● BATTERY-POWERED EQUIPMENT
● BRIDGE AMPLIFIERS
● 4-20mA CURRENT TRANSMITTERS
● VOLTAGE COMPARATOR
● LOW DRIFT: 2.5µV/°C max
● LOW IOS: 1.5nA max
● LOW NOISE: 0.55µVp-p, 0.1Hz to 10Hz
DESCRIPTION
The OPA1013 dual operational amplifier provides
precision performance in single power supply and low
power applications. It is laser trimmed for low offset
voltage and drift, greatly reducing the large errors
common with LM324-type op amps. Input offset
current is also trimmed to reduce errors in high im-
pedance applications.
The OPA1013 is characterized for operation at both
+5V (single supply) and ±15V power supplies. When
operated from a single supply, the input common-mode
range includes ground and the output can swing to
within 15mV of ground. Completely independent bias-
ing networks eliminate interaction between the two
amplifiers—even when one is used as a comparator.
The OPA1013 is available in an 8-pin plastic DIP
specified for the 0°C to +70°C temperature range.
V+
3.3µA
8
Simplified Circuit
(Half of Dual)
3.3µA
7.5µA
2nd
Gain
Stage
22Ω
400Ω
0.9V
400Ω
Out
1, 7
In –
2, 6
In +
3, 5
22Ω
V–
4
International Airport Industrial Park
•
Mailing Address: PO Box 11400
Cable: BBRCORP
•
Tucson, AZ 85734
•
Street Address: 6730 S. Tucson Blvd.
• Tucson, AZ 85706
Tel: (520) 746-1111
•
Twx: 910-952-1111
•
•
Telex: 066-6491
•
FAX: (520) 889-1510
•
Immediate Product Info: (800) 548-6132
© 1990 Burr-Brown Corporation
PDS-1059F
Printed in U.S.A. December, 1994
SBOS005
SPECIFICATIONS
ELECTRICAL
VS = ±15V, VCM = 0V, TA = +25°C unless otherwise noted.
OPA1013CN8
TYP
OPA1013DN8
TYP
PARAMETER
CONDITION
MIN
MAX
MIN
MAX
UNITS
Input Offset Voltage
Time Stability
Input Offset Current
Input Bias Current
Voltage Noise, BW = 0.1 to 10Hz
Noise Density, f = 10Hz
f = 1kHz
Current Noise Density, f = 10Hz
Input Resistance: Differential
Input Resistance: Common-Mode
Open-Loop Voltage Gain
±50
0.5
±0.08
7
0.55
28
25
0.12
300
4
2.9
1.9
+13.8
–15.3
114
117
137
±14
0.35
±0.35
±300
±200
±800
µV
µV/Mo
nA
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
±1.5
30
*
*
nA
µVp-p
nV/√Hz
nV/√Hz
pA/√Hz
MΩ
70
*
GΩ
V
O = ±10V, RL = 2kΩ
1.2
0.5
+13.5
–15
97
100
120
±12.5
0.2
*
*
*
*
*
*
*
*
*
V/µV
V/µV
V
V
dB
dB
dB
V
V/µs
mA
VO = ±10V, RL = 600Ω
Common-Mode Input Range
Common-Mode Rejection
Power Supply Rejection
Channel Separation
Voltage Output
Slew Rate
Quiescent Current (per amplifier)
V
CM = +13.5 to –15V
VS = ±2 to ±18V
O = ±10V, RL = 2kΩ
RL = 2kΩ
V
±0.55
*
*Specification same as OPA1013CN8.
V
S = +5V/0V, VCM = 0V, VO = +1.4V, TA = +25°C unless otherwise noted.
OPA1013CN8
TYP
OPA1013DN8
TYP
PARAMETER
CONDITION
MIN
MAX
MIN
MAX
UNITS
Input Offset Voltage
Input Offset Current
Input Bias Current
±90
±3.0
10
±450
±2.0
50
±250
±950
*
*
µV
nA
nA
*
*
*
Open-Loop Voltage Gain
VO = 5mV to 4V
0.1
V/µV
RL = 500Ω
Common-Mode Input Range
+3.5
0
+3.8
–0.3
15
*
*
*
*
*
*
*
*
*
*
V
V
mV
mV
mV
V
Voltage Output Low
Low
Low
High
No Load
RL = 600Ω to Ground
SINK = 1mA
No Load
RL = 600Ω to Ground
25
10
350
*
*
*
5
I
200
4.4
4
4
3.4
*
*
High
V
mA
Quiescent Current (per amplifier)
0.33
0.5
*
*Specification same as OPA1013CN8.
TA = 0°C to +70°C, VS = ±15V, VCM = 0V unless otherwise noted.
OPA1013CN8
TYP
OPA1013DN8
TYP
PARAMETER
CONDITION
MIN
MAX
MIN
MAX
UNITS
Input Offset Voltage
±80
±110
0.4
±0.3
±0.5
9
±400
±570
2.5
±2.8
±6
±230
±280
0.7
*
*
±1000
±1200
µV
µV
µV/°C
nA
nA
nA
VS = +5/0V, VO = +1.4V
Input Offset Voltage Drift(1)
Input Offset Current
5
*
*
*
*
VS = +5/0V, VO = +1.4V
VS = +5/0V, VO = +1.4V
Input Bias Current
38
90
*
*
13
nA
Open-Loop Voltage Gain
Common-Mode Rejection
Power Supply Rejection
Voltage Output
V
V
O = ±10V, RL = 2kΩ
CM = +13 to –15V
VS = ±2 to ±18V
RL = 2kΩ
0.7
94
97
2.2
*
*
*
*
*
*
*
*
*
*
V/µV
dB
dB
V
mV
V
113
116
±13.9
6
±12.0
V
V
O Low
O High
VS = +5/0V, RL = 600Ω
VS = +5/0V, RL = 600Ω
13
*
3.2
3.9
*
Quiescent Current (per amplifier)
±0.37
0.34
±0.6
0.55
*
*
*
*
mA
mA
VS = +5/0V, VO = +1.4V
*Specification same as OPA1013CN8.
NOTE: (1) Guaranteed by design. This specification is established to a 98% confidence level.
®
OPA1013
2
DICE INFORMATION
PAD
FUNCTION
1
2
3
4
5
6
7
8
Output A
–In A
+In A
V–
+In B
–In B
Output B
V+
Substrate Bias: –VS
4
MECHANICAL INFORMATION
MILS (0.001")
MILLIMETERS
Die Size
Die Thickness
Min. Pad Size
112 x 100 ±5
20 ±3
2.84 x 2.54 ±0.13
0.51 ±0.08
0.10 x 0.10
4 x 4
Transistor Count
Backing
92
Gold
OPA1013 DIE TOPOGRAPHY
ABSOLUTE MAXIMUM RATINGS
CONNECTION DIAGRAM
Power Supply Voltage ....................................................................... ±22V
Differential Input Voltage ................................................................... ±30V
Input Voltage...................................................................... V+ to (V–) –5V
Output Short Circuit (TA = 25°C) ............................................. Continuous
Operating Temperature: ....................................................... 0°C to +70°C
Storage Temperature.......................................................... –65 to +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C
N8 — Plastic Package — Top View
1
2
3
4
8
7
6
5
V+
Out A
–In A
+In A
V–
A
–
Out B
–In B
+In B
B
ORDERING INFORMATION
–
MODEL
PACKAGE
TEMPERATURE RANGE
OPA1013CN8
OPA1013DN8
Plastic DIP
Plastic DIP
0°C to +70°C
0°C to +70°C
PACKAGE INFORMATION
PACKAGE DRAWING
NUMBER(1)
MODEL
PACKAGE
OPA1013CN8
OPA1013DN8
Plastic DIP
Plastic DIP
006
006
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix D of Burr-Brown IC Data Book.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
3
OPA1013
TYPICAL PERFORMANCE CURVES
TA = +25°C unless otherwise noted.
OFFSET VOLTAGE
vs BALANCED SOURCE RESISTANCE
OFFSET VOLTAGE vs TEMPERATURE
10
1
R
R
VS = ±15V
200
100
0
+
–
VS = 5V/0V, 25°C
0.1
0.01
–100
–200
VS = ±15V, 25°C
6 Representative Devices
1k
3k
10k
30k 100k 300k
1M
3M
10M
–50
–25
0
25
50
75
100
125
Balanced Source Resistor (Ω)
Temperature (°C)
COMMON-MODE REJECTION RATIO
vs FREQUENCY
OFFSET VOLTAGE vs TIME
VS = ±15V
5
4
3
2
1
0
120
100
80
60
40
20
0
V
= ±15V
V
= 5V/0V
Plastic DIP N8 Package
0
1
2
3
4
5
10
100
1k
10k
100k
1M
Time After Power On (Minutes)
Frequency (Hz)
POWER SUPPLY REJECTION RATIO
vs FREQUENCY
0.1Hz TO 10Hz NOISE
V= ±2V to ±18V
120
100
80
60
40
20
0
Negative
Supply
Positive
Supply
0
2
4
6
8
10
0.1
1
10
100
1k
10k
100k
1M
Time (s)
Frequency (Hz)
®
OPA1013
4
TYPICAL PERFORMANCE CURVES (CONT)
TA = +25°C unless otherwise noted.
NOISE DENSITY vs FREQUENCY
10Hz VOLTAGE NOISE DISTRIBUTION
VS = ±15V
1000
200
180
160
140
120
100
80
V
= ±2V to ±18V
340 units tested
from three runs.
300
100
Current
Noise
60
30
10
40
Voltage
Noise
20
0
1
10
100
1k
10
20
30
40
50
60
Frequency (Hz)
Voltage Noise Density (nV/ Hz)
INPUT BIAS CURRENT
SUPPLY CURRENT vs TEMPERATURE
vs COMMON-MODE VOLTAGE
460
420
380
340
300
260
15
10
5
5
VS = ±15V
4
3
VS = 5V/0V
0
2
VS = ±15V
VS = 5V/0V
–5
1
–10
0
–15
–1
–50
–25
0
25
50
75
100
125
0
–5
–10
–15
–20
–25
–30
Temperature (°C)
Input Bias Current (nA)
INPUT BIAS CURRENT
vs TEMPERATURE
INPUT OFFSET CURRENT
vs TEMPERATURE
–1
–0.8
–0.6
–0.4
–0.2
0
–30
–25
VCM = 0V
V
S = 5V/0V
VCM = 0V
VS = 5V/0V
–25
V
= ±2.5V
–20
–15
–10
–5
VS = ±2.5V
VS = ±15V
VS = ±15V
0
–50
0
25
50
75
100
125
–50
–25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
®
5
OPA1013
TYPICAL PERFORMANCE CURVES (CONT)
TA = +25°C unless otherwise noted.
OUTPUT SATURATION AND SINK CURRENT
vs TEMPERATURE
OUTPUT SHORT CIRCUIT CURRENT vs TIME
50
40
10
1
VS = ±15V
0°C
+V = 5V to 30V
–V = 0V
25°C
30
ISINK = 10mA
20
70°C
10
ISINK = 5mA
0
–10
–20
–30
–40
–50
ISINK = 1mA
0.1
0.01
70°C
25°C
0°C
ISINK = 100µA
I
SINK = 10µA
SINK = 0
I
0
1
2
3
–50
–25
0
25
50
75
100
125
Time (Minutes)
Temperature (°C)
VOLTAGE GAIN vs FREQUENCY
CL = 100pF
VOLTAGE GAIN vs LOAD RESISTANCE
VO = ±10V with VS = ±15V
10M
140
120
100
80
VO = 20mV to 3.5V
with VS = 5V/0V
VS = ±15V
(1)
60
1M
VS = 5V/0V
40
20
0
(2)
100k
–20
100
1k
10k
0.01 0.1
1
10 100
1k
10k 100k 1M 10M
Load Resistance to Ground (
)
Ω
Frequency (Hz)
NOTES: (1) TA = +25°C, VS = ±15V. (2) TA = +25°C, VS = 5V/0V.
GAIN AND PHASE vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
VS = ±15V
80
160
VCM = 0V
20
10
VIN = 20Vp-p to 5kHz
RL = 2kΩ
C
L = 100pF 100
120
140
120
100
80
Limited by
thermal
interaction
140
VS = ±15V
Phase
VS = ±15V
RS =100Ω
160
Gain
VS = 5V/0V
RS =1k
0
180
200
220
240
VS = 5V/0V
Limited by
pin-to-pin
capacitance
–10
60
0.1
1
10
10
100
1k
10k
100k
1M
Frequency (MHz)
Frequency (Hz)
®
OPA1013
6
TYPICAL PERFORMANCE CURVES (CONT)
LARGE SIGNAL TRANSIENT RESPONSE
VS = ±15V, G = +1
SMALL SIGNAL TRANSIENT RESPONSE
VS = ±15V, G = +1
+50mV
+10V
0V
0mV
–10V
–50mV
VS = 5V/0V
SMALL SIGNAL TRANSIENT RESPONSE
VS = 5V/0V, G = +1, RL = 600Ω to Ground
LARGE SIGNAL TRANSIENT RESPONSE
VS = 5V/0V, G = +1, RL = 4.7kV to 5V
4V
2V
0V
100mV
50mV
0mV
Input = 0V to 4V Pulse
COMPARATOR RISE RESPONSE TIME
10mV, 5mV, 2mV Overdrives
LARGE SIGNAL TRANSIENT RESPONSE
VS = 5V/0V, G = +1, No Load
4
4V
2V
Output (V)
Input (mV)
2
0
0
0V
–100
Input = 0V to 4V Pulse
VS = 5V/0V
®
7
OPA1013
TYPICAL PERFORMANCE CURVES (CONT)
COMPARATOR FALL RESPONSE TIME
10mV, 5mV, 2mV Overdrives
4
Output (V)
2
0
100
Input (mV)
0
VS = 5V/0V
INPUT PROTECTION
APPLICATIONS INFORMATION
The circuitry of the OPA1013 is protected against overload
for input voltages ranging from the positive supply voltage
to 5V below the negative supply voltage (below ground in
single supply operation). No external protection circuitry is
required, as it is with other common single-supply op amps.
The OPA1013 is unity-gain stable, making it easy to use and
free from oscillations in the widest range of circuitry. Follow
good design practice by bypassing the power supplies close
to the op amp pins. In most cases 0.1µF ceramic capacitors
are adequate.
Furthermore, the OPA1013 is free from phase-reversal prob-
lems common with other single-supply op amps. When the
inputs are driven below ground (or below the negative
power supply), the output polarity remains correct.
SINGLE POWER SUPPLY OPERATION
The OPA1013 is specified for operation from a single power
supply. This means that linear operation continues with the
input terminals at (or even somewhat below) ground poten-
tial. When used in a non-inverting amplifier, 0V input must
produce 0V output. In practice, the output swing is limited
to approximately 15mV above ground with no load. Output
swing near ground can be optimized when the output load is
connected to ground. If the output must sink current, the
ability to swing near ground will be diminished. The output
swings to within approximately 200mV of ground when
sinking 1mA.
COMPARATOR OPERATION
The OPA1013 functions well as a comparator, where high
speed is not required. Sometimes, in fact, the low offset and
docile characteristics of the OPA1013 may simplify the
design of comparator circuitry. The two op amps in the
OPA1013 use completely independent bias circuitry to avoid
interaction when the inputs are over-driven. Driving one op
amp into saturation will not affect the characteristics of the
other amplifier. The outputs of the OPA1013 can drive one
TTL load. Quiescent current remains stable when the inputs
are overdriven.
+VS
0-4mA In
0-4mA Out
R3
100Ω
+
1/2
N channel enhancement MOSFET
Supertex, Siliconix, Motorola, etc.
OPA1013
C1
0.001µF
or
–
2 x 2N2222
R4
500Ω
R2
50Ω
R1
500Ω
To Ground or –VS
FIGURE 1. Precision Current Mirror.
®
OPA1013
8
V+
7
–
+
5
6
1
V1
1/2
–
OPA1013
2
3
–
+
VO
VO = V2 – V1
–
+
Input common-mode range
extends to approximately
150mV above V– supply — limited
by OPA1013 output swing.
INA105
4
V2
1/2
OPA1013
+
V–
FIGURE 2. Instrumentation Amplifier.
V+
7
1
8
2
REF200
100µA
5
1/2
2
3
OPA1013
6
VO
–
+
PMI
MAT03
VO = V2 – V1
V1
V2
1
Input
INA105
1/2
OPA1013
V–
Input common-mode range extends
to approximately 200mV below V– supply.
FIGURE 3. Instrumentation Amplifier.
V+
VI
(+100mV)
(–100mV)
REF200
100µA
V+
Output
1/2
1kΩ
OPA1013
Output
TTL or
CMOS
1/2
1kΩ
OPA1013
VI
NOTE: VI must sink 100µA.
FIGURE 4. Window Comparator.
®
9
OPA1013
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明