OPA2380 [TI]
OPA2380 - 双通道高速精密跨阻放大器;
| 型号： | OPA2380 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | OPA2380 - 双通道高速精密跨阻放大器 放大器 电信 电信集成电路 电信电路 |
| 文件： | 总22页 (文件大小：695K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OPA380
OPA2380
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
Precision, High-Speed
Transimpedance Amplifier
FD EATURES
DESCRIPTION
> 1MHz TRANSIMPEDANCE BANDWIDTH
The OPA380 family of transimpedance amplifiers provides
high-speed (90MHz Gain Bandwidth [GBW]) operation, with
extremely high precision, excellent long-term stability, and
very low 1/f noise. It is ideally suited for high-speed
photodiode applications. The OPA380 features an offset
voltage of 25µV, offset drift of 0.1µV/°C, and bias current of
50pA. The OPA380 far exceeds the offset, drift, and noise
performance that conventional JFET op amps provide.
D
D
D
D
D
D
D
D
D
D
EXCELLENT LONG-TERM V
STABILITY
OS
BIAS CURRENT: 50pA (max)
OFFSET VOLTAGE: 25µV (max)
DYNAMIC RANGE: 4 to 5 Decades
DRIFT: 0.1µV/°C (max)
GAIN BANDWIDTH: 90MHz
QUIESCENT CURRENT: 7.5mA
SUPPLY RANGE: 2.7V to 5.5V
SINGLE AND DUAL VERSIONS
MicroSize PACKAGE: MSOP-8
The signal bandwidth of a transimpedance amplifier depends
largely on the GBW of the amplifier and the parasitic
capacitance of the photodiode, as well as the feedback
resistor. The 90MHz GBW of the OPA380 enables a trans-
impedance bandwidth of > 1MHz in most configurations. The
OPA380 is ideally suited for fast control loops for power level
on an optical fiber.
AD PPLICATIONS
PHOTODIODE MONITORING
As a result of the high precision and low-noise characteristics
of the OPA380, a dynamic range of 4 to 5 decades can be
achieved. For example, this capability allows the
measurement of signal currents on the order of 1nA, and up
to 100µA in a single I/V conversion stage. In contrast to
logarithmic amplifiers, the OPA380 provides very wide
bandwidth throughout the full dynamic range. By using an
external pull-down resistor to –5V, the output voltage range
can be extended to include 0V.
D
D
D
PRECISION I/V CONVERSION
OPTICAL AMPLIFIERS
CAT-SCANNER FRONT-END
RF
+5V
7
The OPA380 (single) is available in MSOP-8 and SO-8
packages. The OPA2380 (dual) is available in the
miniature MSOP-8 package. They are specified from
–40°C to +125°C.
OPA380
2
VOUT
(0V to 4.4V)
6
RP
Photodiode
(Optional
Pulldown
Resistor)
OPA380 RELATED DEVICES
67pF
1MΩ
PRODUCT
OPA300
OPA350
OPA335
OPA132
OPA656/7
LOG112
LOG114
IVC102
FEATURES
−5V
150MHz CMOS, 2.7V to 5.5V Supply
100kΩ
500µV V , 38MHz, 2.5V to 5V Supply
OS
10µV V , Zero-Drift, 2.5V to 5V Supply
3
OS
75pF
16MHz GBW, Precision FET Op Amp, 15V
230MHz, Precision FET, 5V
4
LOG amp, 7.5 decades, 4.5V to 18V Supply
LOG amp, 7.5 decades, 2.25V to 5.5V Supply
Precision Switched Integrator
DDC112
Dual Current Input, 20-Bit ADC
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ
ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ
ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ
Copyright 2003-2007, Texas Instruments Incorporated
www.ti.com
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
(1)
ELECTROSTATIC DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
Voltage Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handledwith appropriate precautions. Failure to observe
(2)
Signal Input Terminals , Voltage . . . . . . . . . . −0.5V to (V+) + 0.5V
Current . . . . . . . . . . . . . . . . . . . . . 10mA
(3)
Short-Circuit Current
. . . . . . . . . . . . . . . . . . . . . . . . . Continuous
proper handling and installation procedures can cause damage.
Operating Temperature Range . . . . . . . . . . . . . . . −40°C to +125°C
Storage Temperature Range . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
ESD Rating (Human Body Model) . . . . . . . . . . . . . . . . . . . . . . . 2000V
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
(1)
Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(1)
PACKAGE/ORDERING INFORMATION
PACKAGE
MARKING
PRODUCT
PACKAGE-LEAD
(2)
(3)
Input terminals are diode clamped to the power-supply rails. Input
signals that can swing more than 0.5V beyond the supply rails
should be current limited to 10mA or less.
OPA380
OPA380
OPA2380
MSOP-8
SO-8
AUN
OPA380A
BBX
Short-circuit to ground; one amplifier per package.
MSOP-8
(1)
For the most current package and ordering information, see the
Package Option Addendum at the end of this document, or see
the TI web site at www.ti.com.
PIN ASSIGNMENTS
Top View
OPA2380
OPA380
NC(1)
V+
NC(1)
1
2
3
4
8
7
6
5
V+
Out A
1
2
3
4
8
7
6
5
−
−
In A
Out B
In
Out
−
+In A
In B
+In B
+In
NC(1)
−
V
−
V
MSOP-8
MSOP-8, SO-8
NOTES: (1) NC indicates no internal connection.
2
ꢂ ꢀꢉꢠ ꢡ ꢢ
ꢂ ꢀꢉꢣ ꢠ ꢡꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
ELECTRICAL CHARACTERISTICS: OPA380 (SINGLE), V = 2.7V to 5.5V
S
Boldface limits apply over the temperature range, T = −40°C to +125°C.
A
All specifications at T = +25°C, R = 2kΩ connected to V /2, and V
= V /2, unless otherwise noted.
A
L
S
OUT
S
OPA380
TYP
MIN
MAX
PARAMETER
CONDITION
UNITS
OFFSET VOLTAGE
Input Offset Voltage
Drift
V
V
= +5V, V
= 0V
4
25
0.1
10
10
µV
OS
S CM
dV /dT
OS
PSRR
0.03
2.4
µV/°C
µV/V
µV/V
vs Power Supply
Over Temperature
Long-Term Stability
V
= +2.7V to +5.5V, V
= 0V
S
CM
V
S
= +2.7V to +5.5V, V
= 0V
CM
(1)
See Note (1)
1
Channel Separation, dc
µV/V
INPUT BIAS CURRENT
Input Bias Current
I
V
V
= V /2
3
50
pA
pA
B
CM
S
Over Temperature
Input Offset Current
Typical Characteristics
6
I
= V /2
100
OS
CM
S
NOISE
Input Voltage Noise, f = 0.1Hz to 10Hz
Input Voltage Noise Density, f = 10kHz
Input Voltage Noise Density, f > 1MHz
Input Current Noise Density, f = 10kHz
e
n
e
n
e
n
V
S
V
S
V
S
V
S
= +5V, V
= +5V, V
= +5V, V
= +5V, V
= 0V
= 0V
= 0V
= 0V
3
µV
CM
CM
CM
CM
PP
67
5.8
10
nV/√Hz
nV/√Hz
fA/√Hz
i
n
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
V
V−
(V+) − 1.8V
V
CM
CMRR
(V−) < V
< (V+) – 1.8V
100
110
dB
CM
INPUT IMPEDANCE
Differential Capacitance
Common-Mode Resistance and Inverting Input
Capacitance
1.1
pF
13
10 || 3
Ω || pF
OPEN-LOOP GAIN
Open-Loop Voltage Gain
A
OL
0.1V < V < (V+) − 0.7V, V = 5V, V
= V /2
110
130
dB
O
S
CM
S
0.1V < V < (V+) − 0.6V, V = 5V, V
= V /2,
S
O
S
CM
110
130
dB
T
= −40°C to +85°C
A
0V < V < (V+) − 0.7V, V = 5V, V
= 0V,
O
S
CM
106
120
dB
(2)
R
P
= 2kΩ to −5V
0V < V < (V+) − 0.6V, V = 5V, V
= 0V,
O
S
CM
106
120
dB
(2)
R
P
= 2kΩ to −5V , T = −40°C to +85°C
A
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
C = 50pF
L
GBW
SR
90
80
2
MHz
V/µs
µs
G = +1
V = +5V, 4V Step, G = +1
S
(3)
Settling Time, 0.01%
t
S
(4)(5)
Overload Recovery Time
V
× G = > V
100
ns
IN
S
OUTPUT
Voltage Output Swing from Positive Rail
Voltage Output Swing from Negative Rail
Voltage Output Swing from Positive Rail
Voltage Output Swing from Negative Rail
Output Current
R
= 2kΩ
= 2kΩ
400
60
600
100
600
0
mV
mV
mV
mV
L
R
L
(2)
(2)
R
R
= 2kΩ to −5V
= 2kΩ to −5V
400
−20
P
P
I
See Typical Characteristics
OUT
Short-Circuit Current
I
150
mA
SC
Capacitive Load Drive
C
See Typical Characteristics
40
LOAD
R
O
Open-Loop Output Impedance
f = 1MHz, I = 0A
Ω
O
POWER SUPPLY
Specified Voltage Range
Quiescent Current
Over Temperature
V
2.7
5.5
V
S
I
Q
I
O
= 0A
7.5
9.5
mA
mA
10
TEMPERATURE RANGE
Specified and Operating Range
Storage Range
−40
−65
+125
+150
°C
°C
Thermal Resistance
MSOP-8, SO-8
q
JA
150
°C/W
(1)
(2)
300-hour life test at 150°C demonstrated randomly distributed variation approximately equal to measurement repeatability of 1µV.
Tested with output connected only to R , a pulldown resistor connected between V
and −5V, as shown in Figure 5. See also applications section, Achieving
P
OUT
Output Swing to Ground.
(3)
(4)
(5)
Transimpedance frequency of 1MHz.
Time required to return to linear operation.
From positive rail.
3
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
ELECTRICAL CHARACTERISTICS: OPA2380 (DUAL), V = 2.7V to 5.5V
S
Boldface limits apply over the temperature range, T = −40°C to +125°C.
A
All specifications at T = +25°C, R = 2kΩ connected to V /2, and V
= V /2, unless otherwise noted.
A
L
S
OUT
S
OPA2380
TYP
MIN
MAX
PARAMETER
CONDITION
UNITS
OFFSET VOLTAGE
Input Offset Voltage
Drift
V
V
= +5V, V
= 0V
4
25
0.1
10
10
µV
OS
S CM
dV /dT
OS
PSRR
0.03
2.4
µV/°C
µV/V
µV/V
vs Power Supply
Over Temperature
Long-Term Stability
V
= +2.7V to +5.5V, V
= 0V
S
CM
V
S
= +2.7V to +5.5V, V
= 0V
CM
(1)
See Note (1)
1
Channel Separation, dc
µV/V
INPUT BIAS CURRENT
Input Bias Current, Inverting Input
I
I
V
V
= V /2
3
50
pA
pA
B
CM
S
Noninverting Input
Over Temperature
NOISE
= V /2
3
200
B
CM
S
Typical Characteristics
Input Voltage Noise, f = 0.1Hz to 10Hz
Input Voltage Noise Density, f = 10kHz
Input Voltage Noise Density, f > 1MHz
Input Current Noise Density, f = 10kHz
e
n
e
n
e
n
i
n
V
S
V
S
V
S
V
S
= +5V, V
= +5V, V
= +5V, V
= +5V, V
= 0V
= 0V
= 0V
= 0V
3
µV
CM
CM
CM
CM
PP
67
5.8
10
nV/√Hz
nV/√Hz
fA/√Hz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
V
V−
(V+) − 1.8V
V
CM
CMRR
(V−) < V
< (V+) – 1.8V
95
105
dB
CM
INPUT IMPEDANCE
Differential Capacitance
Common-Mode Resistance and Inverting Input
Capacitance
1.1
pF
13
10 || 3
Ω || pF
OPEN-LOOP GAIN
Open-Loop Voltage Gain
A
OL
0.12V < V < (V+) − 0.7V, V = 5V, V
= V /2
110
130
dB
O
S
CM
S
0.12V < V < (V+) − 0.6V, V = 5V, V
= V /2,
S
O
S
CM
110
130
dB
T
= −40°C to +85°C
A
0V < V < (V+) − 0.7V, V = 5V, V
= 0V,
O
S
CM
106
120
dB
(2)
R
P
= 2kΩ to −5V
0V < V < (V+) − 0.6V, V = 5V, V
= 0V,
O
S
CM
106
120
dB
(2)
R
P
= 2kΩ to −5V , T = −40°C to +85°C
A
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
C = 50pF
L
GBW
SR
90
80
2
MHz
V/µs
µs
G = +1
V = +5V, 4V Step, G = +1
S
(3)
Settling Time, 0.01%
t
S
(4)(5)
Overload Recovery Time
V
× G = > V
100
ns
IN
S
OUTPUT
Voltage Output Swing from Positive Rail
Voltage Output Swing from Negative Rail
Voltage Output Swing from Positive Rail
Voltage Output Swing from Negative Rail
Output Current
R
= 2kΩ
= 2kΩ
400
80
600
120
600
0
mV
mV
mV
mV
L
R
L
(2)
(2)
R
R
= 2kΩ to −5V
= 2kΩ to −5V
400
−20
P
P
I
See Typical Characteristics
OUT
Short-Circuit Current
I
150
mA
SC
Capacitive Load Drive
C
See Typical Characteristics
40
LOAD
R
O
Open-Loop Output Impedance
f = 1MHz, I = 0A
Ω
O
POWER SUPPLY
Specified Voltage Range
Quiescent Current (per amplifier)
Over Temperature
V
2.7
5.5
V
S
I
Q
I
O
= 0A
7.5
9.5
mA
mA
10
TEMPERATURE RANGE
Specified and Operating Range
Storage Range
−40
−65
+125
+150
°C
°C
Thermal Resistance
MSOP-8
q
JA
150
°C/W
(1)
(2)
300-hour life test at 150°C demonstrated randomly distributed variation approximately equal to measurement repeatability of 1µV.
Tested with output connected only to R , a pulldown resistor connected between V
and −5V, as shown in Figure 5. See also applications section, Achieving
P
OUT
Output Swing to Ground.
(3)
(4)
(5)
Transimpedance frequency of 1MHz.
Time required to return to linear operation.
From positive rail.
4
ꢂ ꢀꢉꢠ ꢡ ꢢ
ꢂ ꢀꢉꢣ ꢠ ꢡꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS: V = +2.7V to +5.5V
S
All specifications at T = +25°C, R = 2kΩ connected to V /2, and V
= V /2, unless otherwise noted.
S
A
L
S
OUT
POWER−SUPPLY REJECTION RATIO AND
COMMON−MODE REJECTION vs FREQUENCY
OPEN−LOOP GAIN AND PHASE vs FREQUENCY
Gain
160
140
120
100
80
140
120
100
80
90
45
0
−
−
−
−
−
−
45
90
Phase
PSRR
CMRR
60
60
40
135
180
225
270
40
20
20
0
0
−
−
20
20
0.1
1
10
100
1k
10k 100k 1M 10M 100M
10
100
1k
10k
100k
1M
10M 100M
Frequency (Hz)
Frequency (Hz)
INPUT VOLTAGE NOISE SPECTRAL DENSITY
QUIESCENT CURRENT vs TEMPERATURE
VS = +5.5V
1000
100
10
8
7
6
5
4
3
2
1
0
VS = +2.7V
1
−
−
10
100
1k
10k
100k
1M
10M
40 25
0
25
50
75
100
125
_
Frequency (Hz)
Temperature ( C)
QUIESCENT CURRENT vs SUPPLY VOLTAGE
INPUT BIAS CURRENT vs TEMPERATURE
8
7
6
5
4
3
2
1
1000
100
10
1
−
−
40 25
0
25
50
75
100
125
2.7 3.0
3.5
4.0
4.5
5.0
5.5
_
Temperature ( C)
Supply Voltage (V)
5
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS: V = +2.7V to +5.5V (continued)
S
All specifications at T = +25°C, R = 2kΩ connected to V /2, and V
= V /2, unless otherwise noted.
S
A
L
S
OUT
INPUT BIAS CURRENT
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
vs INPUT COMMON−MODE VOLTAGE
(V+)
25
20
15
10
5
−
−
(V+)
(V+)
1
2
−
+
IB
_
−
_
_
+25 C 40 C
+125 C
0
−
(V ) +2
−
5
IB
−
−
−
−
10
15
20
25
−
(V ) +1
−
(V )
0
50
100
150
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Output Current (mA)
Input Common−Mode Voltage (V)
SHORT−CIRCUIT CURRENT vs TEMPERATURE
VS = 5V
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
200
150
100
50
+ISC
0
−
ISC
−
50
−
−
100
150
−
−
40 25
0
25
50
75
100
125
−
−
−
−
−
5
25
20
15
10
0
5
10
15
20
25
_
µ
Offset Voltage ( V)
Temperature ( C)
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
GAIN BANDWIDTH vs POWER SUPPLY VOLTAGE
95
90
85
80
75
70
2.5
3.5
4.5
5.5
−
−
−
−
−
0.10 0.08 0.06 0.04 0.02
0
0.02 0.04 0.06 0.08 0.1
µ
_
Power Supply Voltage (V)
Offset Voltage Drift ( V/ C)
6
ꢂ ꢀꢉꢠ ꢡ ꢢ
ꢂ ꢀꢉꢣ ꢠ ꢡꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS: V = +2.7V to +5.5V (continued)
S
All specifications at T = +25°C, R = 2kΩ connected to V /2, and V
= V /2, unless otherwise noted.
S
A
L
S
OUT
TRANSIMPEDANCE AMP CHARACTERISTIC
CDIODE = 100pF
140
130
120
110
100
90
Circuit for Transimpedance Amplifier Characteristic curves on this page.
Ω
RF = 10M
CF
Ω
RF = 1M
CF = 0.5pF
CF = 2pF
CF = 5pF
CF = 18pF
RF
Ω
RF = 100k
80
CSTRAY
70
Ω
RF = 10k
60
50
Ω
RF = 1k
40
OPA380
30
CSTRAY (parasitic) = 0.2pF
CDIODE
20
100
1k
10k
100k
Frequency (Hz)
1M
10M
100M
100M
100M
TRANSIMPEDANCE AMP CHARACTERISTIC
TRANSIMPEDANCE AMP CHARACTERISTIC
CDIODE = 20pF
140
140
130
120
110
100
90
CDIODE = 50pF
Ω
Ω
RF = 10M
RF = 10M
130
120
110
100
90
Ω
RF = 1M
CF = 0.5pF
CF = 1.5pF
CF = 4pF
CF = 12pF
Ω
Ω
RF = 1M
Ω
RF = 100k
RF = 100k
CF = 1pF
CF = 2.5pF
80
80
70
Ω
RF = 10k
Ω
RF = 10k
70
60
60
50
Ω
RF = 1k
Ω
RF = 1k
50
CF = 7pF
40
40
30
CSTRAY (parasitic) = 0.2pF
1k 10k
CSTRAY (parasitic) = 0.2pF
1k 10k
20
100
30
100
100k
1M
10M
100M
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
TRANSIMPEDANCE AMP CHARACTERISTIC
CDIODE = 1pF
TRANSIMPEDANCE AMP CHARACTERISTIC
CDIODE = 10pF
140
130
120
110
100
90
140
130
120
110
100
90
Ω
RF = 10M
Ω
RF = 10M
Ω
Ω
RF = 1M
Ω
Ω
RF = 1M
RF = 100k
CF = 0.5pF
CF = 2pF
RF = 100k
CF = 0.5pF
CF = 1pF
80
80
Ω
RF = 10k
70
Ω
RF = 10k
70
Ω
RF = 1k
60
Ω
RF = 1k
60
50
CF = 5pF
CF = 2.5pF
1M 10M
50
40
CSTRAY (parasitic) = 0.2pF
1k 10k
CSTRAY (parasitic) = 0.2pF
1k 10k
40
100
30
100
100k
100k
1M
10M
100M
Frequency (Hz)
Frequency (Hz)
7
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS: V = +2.7V to +5.5V (continued)
S
All specifications at T = +25°C, R = 2kΩ connected to V /2, and V
= V /2, unless otherwise noted.
S
A
L
S
OUT
SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE
SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE
50
45
40
35
30
25
20
15
10
5
50
45
40
35
30
25
20
15
10
5
2.5pF
2.5pF
Ω
10k
Ω
10k
+5V
+2.5V
RS
VOUT
RS
OPA380
VO UT
OPA380
Ω
C
RP = 2k
C
RF = 2kΩ
−
5V
−
2.5V
No RS
No RS
Ω
RS = 100
Ω
RS = 100
0
0
10
100
1000
10
100
Load Capacitance (pF)
1000
Load Capacitance (pF)
SMALL−SIGNAL STEP RESPONSE
OVERLOAD RECOVERY
3.2pF
Ω
RL = 2k
Ω
50k
VOUT
−
= 5V
VP
+5V
V
OUT
I
IN
1.6mA
Ω
2k
VP = 0V
V
P
IIN
Time (100ns/div)
Time (100ns/div)
LARGE−SIGNAL STEP RESPONSE
CHANNEL SEPARATION vs INPUT FREQUENCY
140
120
100
80
Ω
RL = 2k
2.5pF
Ω
10k
60
2.5V
40
Ω
2k
20
−
2.5V
0
Time (100ns/div)
10
100
1k
10k
100k
1M
10M
100M
Frequency (Hz)
8
ꢂ ꢀꢉꢠ ꢡ ꢢ
ꢂ ꢀꢉꢣ ꢠ ꢡꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
OPERATING VOLTAGE
APPLICATIONS INFORMATION
BASIC OPERATION
The OPA380 series op amps are fully specified from
2.7V to 5.5V over a temperature range of −40°C to
+125°C. Parameters that vary significantly with operat-
ing voltages or temperature are shown in the Typical
Characteristics.
The OPA380 is a high-performance transimpedance
amplifier with very low 1/f noise. As a result of its unique
architecture, the OPA380 has excellent long-term input
voltage offset stability—a 300-hour life test at 150°C
demonstrated
randomly
distributed
variation
INTERNAL OFFSET CORRECTION
approximately equal to measurement repeatability of
1µV.
The OPA380 series op amps use an auto-zero topology
with a time-continuous 90MHz op amp in the signal
path. This amplifier is zero-corrected every 100µs using
a proprietary technique. Upon power-up, the amplifier
The OPA380 performance results from an internal
auto-zero amplifier combined with a high-speed
amplifier. The OPA380 has been designed with circuitry
to improve overload recovery and settling time over a
traditional composite approach. It has been specifically
designed and characterized to accommodate circuit
options to allow 0V output operation (see Figure 3).
requires approximately 400µs to achieve specified V
OS
accuracy, which includes one full auto-zero cycle of
approximately 100µs and the start-up time for the bias
circuitry. Prior to this time, the amplifier will function
properly but with unspecified offset voltage.
The OPA380 is used in inverting configurations, with the
noninverting input used as a fixed biasing point.
Figure 1 shows the OPA380 in a typical configuration.
Power-supply pins should be bypassed with 1µF ceramic
or tantalum capacitors. Electrolytic capacitors are not
recommended.
This design has virtually no aliasing and very low noise.
Zero correction occurs at a 10kHz rate, but there is very
little fundamental noise energy present at that
frequency due to internal filtering. For all practical
purposes, any glitches have energy at 20MHz or higher
and are easily filtered, if required. Most applications are
not sensitive to such high-frequency noise, and no
filtering is required.
CF
RF
INPUT VOLTAGE
The input common-mode voltage range of the OPA380
series extends from V− to (V+) – 1.8V. With input
signals above this common-mode range, the amplifier
will no longer provide a valid output value, but it will not
latch or invert.
+5V
µ
1 F
λ
(1)
VOUT
(0.5V to 4.4V)
OPA380
INPUT OVERVOLTAGE PROTECTION
V
BIAS = 0.5V
Device inputs are protected by ESD diodes that will
conduct if the input voltages exceed the power supplies
by more than approximately 500mV. Momentary
voltages greater than 500mV beyond the power supply
can be tolerated if the current is limited to 10mA. The
OPA380 series feature no phase inversion when the
inputs extend beyond supplies if the input is current
limited.
NOTE: (1) VOUT = 0.5V in dark conditions.
Figure 1. OPA380 Typical Configuration
9
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
OUTPUT RANGE
ACHIEVING OUTPUT SWING TO GROUND
The OPA380 is specified to swing within at least 600mV
of the positive rail and 100mV of the negative rail with
a 2kΩ load with excellent linearity. Swing to the negative
rail while maintaining good linearity can be extended to
0V—see the section, Achieving Output Swing to
Ground. See the Typical Characteristic curve, Output
Voltage Swing vs Output Current.
Some applications require output voltage swing from
0V to a positive full-scale voltage (such as +4.096V)
with excellent accuracy. With most single-supply op
amps, problems arise when the output signal
approaches 0V, near the lower output swing limit of a
single-supply op amp. A good single-supply op amp
may swing close to single-supply ground, but will not
reach 0V.
The OPA380 can swing slightly closer than specified to
the positive rail; however, linearity will decrease and a
high-speed overload recovery clamp limits the amount
of positive output voltage swing available, as shown in
Figure 2.
The output of the OPA380 can be made to swing to
ground, or slightly below, on a single-supply power
source. This extended output swing requires the use of
another resistor and an additional negative power
supply. A pull-down resistor may be connected between
the output and the negative supply to pull the output
down to 0V. See Figure 3.
OFFSET VOLTAGE vs OUTPUT VOLTAGE
20
VS = 5V
15
10
Ω
−
RP = 2k connected to 5V
RF
5
0
5
λ
V+ = +5V
−
Ω
RL = 2k connected to VS /2
OPA380
VOUT
−
−
−
10
15
20
Effect of clamp
Ω
RP = 2k
−
V
= Gnd
0
1
2
3
4
5
VOUT (V)
−
VP = 5V
Negative Supply
Figure 2. Effect of High-Speed Overload
Recovery Clamp on Output Voltage
Figure 3. Amplifier with Optional Pull-Down
Resistor to Achieve V = 0V
OUT
OVERLOAD RECOVERY
The OPA380 has been designed to prevent output
saturation. After being overdriven to the positive rail, it
will typically require only 100ns to return to linear
operation. The time required for negative overload
recovery is greater, unless a pull-down resistor
connected to a more negative supply is used to extend
the output swing all the way to the negative rail—see the
following section, Achieving Output Swing to Ground.
The OPA380 has an output stage that allows the output
voltage to be pulled to its negative supply rail using this
technique. However, this technique only works with
some types of output stages. The OPA380 has been
designed to perform well with this method. Accuracy is
excellent down to 0V. Reliable operation is assured over
the specified temperature range.
10
ꢂ ꢀꢉꢠ ꢡ ꢢ
ꢂ ꢀꢉꢣ ꢠ ꢡꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
the desired transimpedance gain (R );
BIASING PHOTODIODES IN SINGLE-SUPPLY
CIRCUITS
F
the Gain Bandwidth Product (GBW) for the
OPA380 (90MHz).
The +IN input can be biased with a positive DC voltage
to offset the output voltage and allow the amplifier
output to indicate a true zero photodiode measurement
when the photodiode is not exposed to any light. It will
also prevent the added delay that results from coming
out of the negative rail. This bias voltage appears
across the photodiode, providing a reverse bias for
faster operation. An RC filter placed at this bias point will
reduce noise, as shown in Figure 4. This bias voltage
can also serve as an offset bias point for an ADC with
range that does not include ground.
With these three variables set, the feedback capacitor
value (C ) can be set to control the frequency response.
F
C
is the stray capacitance of R , which is 0.2pF for
STRAY
F
a typical surface-mount resistor.
To achieve a maximally flat, 2nd-order, Butterworth
frequency response, the feedback pole should be set
to:
GBW
4pRFCTOT
1
+
Ǹ
ǒ
STRAYǓ
2pRF CF ) C
Bandwidth is calculated by:
GBW
(1)
(1)
CF
< 1pF
f*3dB
+
Hz
Ǹ
2pRFCTOT
(2)
RF
These
equations
will
result
in
maximum
Ω
10M
transimpedance bandwidth. For even higher
transimpedance bandwidth, the high-speed CMOS
OPA300 (SBOS271 (180MHz GBW)), or the OPA656
(SBOS196 (230MHz GBW)) may be used.
V+
λ
OPA380
VOUT
For additional information, refer to Application Bulletin
AB−050 (SBOA055), Compensate Transimpedance
Amplifiers Intuitively, available for download at
www.ti.com.
µ
0.1 F
Ω
100k
+VBias
(1)
CF
NOTE: (1) CF is optional to prevent gain peaking.
It includes the stray capacitance of RF.
RF
10MΩ
Figure 4. Filtered Reverse Bias Voltage
TRANSIMPEDANCE AMPLIFIER
(2)
CSTRAY
+5V
Wide bandwidth, low input bias current, and low input
voltage and current noise make the OPA380 an ideal
wideband photodiode transimpedance amplifier.
Low-voltage noise is important because photodiode
capacitance causes the effective noise gain of the
circuit to increase at high frequency.
λ
(3)
CTOT
OPA380
VOUT
RP (optional
pulldown resistor)
5V
−
NOTE: (1) CF is optional to prevent gain peaking.
(2) CSTRAY is the stray capacitance of RF
The key elements to a transimpedance design are
shown in Figure 5:
(typically, 0.2pF for a surface−mount resistor).
(3) CTOT is the photodiode capacitance plus OPA380
input capacitance.
the total input capacitance (C
), consisting of the
) plus the parasitic
TOT
photodiode capacitance (C
DIODE
common-mode and differential-mode input
capacitance (3pF + 1.1pF for the OPA380);
Figure 5. Transimpedance Amplifier
11
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
TRANSIMPEDANCE BANDWIDTH AND
NOISE
Ω
RF = 10k
(a)
Limiting the gain set by R can decrease the noise
F
CSTRAY =0.2pF
occurring at the output of the transimpedance circuit.
However, all required gain should occur in the
transimpedance stage, since adding gain after the
transimpedance amplifier generally produces poorer
noise performance. The noise spectral density
λ
OPA380
VOUT
produced by R increases with the square-root of R ,
F
F
whereas the signal increases linearly. Therefore,
signal-to-noise ratio is improved when all the required
gain is placed in the transimpedance stage.
VBIAS
Total noise increases with increased bandwidth. Limit
the circuit bandwidth to only that required. Use a
Ω
RF = 10k
(b)
capacitor, C , across the feedback resistor, R , to limit
F
F
CSTRAY = 0.2pF
CF = 16pF
bandwidth, even if not required for stability if total output
noise is a concern.
Figure 6a shows the transimpedance circuit without any
feedback capacitor. The resulting transimpedance gain
of this circuit is shown in Figure 7. The –3dB point is
approximately 10MHz. Adding a 16pF feedback
capacitor (Figure 6b) will limit the bandwidth and result
in a –3dB point at approximately 1MHz (see Figure 7).
Output noise will be further reduced by adding a filter
λ
OPA380
VOUT
VBIAS
(R
and C
) to create a second pole (Figure
FILTER
FILTER
6c). This second pole is placed within the feedback loop
to maintain the amplifier’s low output impedance. (If the
pole was placed outside the feedback loop, an
additional buffer would be required and would
inadvertently increase noise and dc error).
Ω
RF = 10k
(c)
CSTRAY = 0.2pF
CF = 21pF
Using R
to represent the equivalent diode
DIODE
resistance, and C
for equivalent diode capacitance
TOT
plus OPA380 input capacitance, the noise zero, f , is
Z
RFILTER
calculated by:
Ω
= 100
λ
ǒ
Ǔ
OPA380
RDIODE ) RF
VOUT
fZ
+
CFILTER
= 796pF
ǒ
Ǔ
2pRDIODERF CTOT ) CF
(3)
VBIAS
Figure 6. Transimpedance Circuit Configurations
with Varying Total and Integrated Noise Gain
12
ꢂ ꢀꢉꢠ ꢡ ꢢ
ꢂ ꢀꢉꢣ ꢠ ꢡꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
110
500
400
300
200
100
0
CDIODE = 10pF
CDIODE = 10pF
419µV
See Figure 6a
See Figure 6a
80
50
20
10
−
3dB BW at 1MHz
See Figure 6c
See Figure 6b
See Figure 6c
86µV
30µV
See Figure 6b
10M 100M
−
1
10
100
1k
10k 100k 1M 10M 100M
100
1k
10k
100k
1M
Frequency (Hz)
Frequency (Hz)
Figure 7. Transimpedance Gains for Circuits in
Figure 6
Figure 9. Integrated Output Noise for Circuits in
Figure 6
Figure 10 shows the effect of diode capacitance on
integrated output noise, using the circuit in Figure 6c.
The effect of these circuit configurations on output noise
is shown in Figure 8 and on integrated output noise in
Figure 9. A 2-pole Butterworth filter (maximally flat in
passband) is created by selecting the filter values using
the equation:
For additional information, refer to Noise Analysis of
FET Transimpedance Amplifiers (SBOA060), and
Noise Analysis for High-Speed Op Amps (SBOA066),
available for download from the TI web site.
CFRF + 2CFILTERRFILTER
(4)
with:
79µV
1
80
f*3dB
+
CDIODE
= 100pF
Ǹ
2p RFRFILTERCFCFILTER
(5)
CDIODE
60
0
= 50pF
50µV
35µV
The circuit in Figure 6b rolls off at 20dB/decade. The
circuit with the additional filter shown in Figure 6c rolls
off at 40dB/decade, resulting in improved noise
performance.
CDIODE
= 20pF
30µV
27 V
µ
20
0
CDIODE
= 1pF
CDIODE
= 10pF
See Figure 6c
10 100
300
CDIODE = 10pF
1
1k
10k 100k 1M 10M 100M
Frequency (Hz)
200
Figure 10. Integrated Output Noise for Various
Values of C for Circuit in Figure 6c
See Figure 6a
DIODE
100
See Figure 6b
See Figure 6c
0
1
10
100
1k
10k 100k
1M
10M 100M
Frequency (Hz)
Figure 8. Output Noise for Circuits in Figure 6
13
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
www.ti.com
SBOS291G − NOVEMBER 2003 − REVISED SEPTEMBER 2007
BOARD LAYOUT
CAPACITIVE LOAD AND STABILITY
Minimize photodiode capacitance and stray
capacitance at the summing junction (inverting input).
This capacitance causes the voltage noise of the op
amp to be amplified (increasing amplification at high
frequency). Using a low-noise voltage source to
reverse-bias a photodiode can significantly reduce its
capacitance. Smaller photodiodes have lower
capacitance. Use optics to concentrate light on a small
photodiode.
The OPA380 series op amps can drive up to 500pF pure
capacitive load. Increasing the gain enhances the
amplifier’s ability to drive greater capacitive loads (see
the Typical Characteristic curve, Small-Signal
Overshoot vs Capacitive Load).
One method of improving capacitive load drive in the
unity-gain configuration is to insert a 10Ω to 20Ω
resistor in series with the load. This reduces ringing with
large capacitive loads while maintaining DC accuracy.
Circuit board leakage can degrade the performance of
an otherwise well-designed amplifier. Clean the circuit
board carefully. A circuit board guard trace that
encircles the summing junction and is driven at the
same voltage can help control leakage, as shown in
Figure 11.
DRIVING FAST 16-BIT ANALOG-TO-DIGITAL
CONVERTERS (ADC)
The OPA380 series is optimized for driving a fast 16-bit
ADC such as the ADS8411. The OPA380 op amp
buffers the converter’s input capacitance and resulting
charge injection while providing signal gain. Figure 12
shows the OPA380 in a single-ended method of
interfacing the ADS8411 16-bit, 2MSPS ADC. For
additional information, refer to the ADS8411 data sheet.
RF
λ
OPA380
VOUT
CF
RF
Guard Ring
Ω
15
OPA380
ADS8411
Figure 11. Connection of Input Guard
6800pF
OTHER WAYS TO MEASURE SMALL
CURRENTS
RC Values shown are optimized for the
Logarithmic amplifiers are used to compress extremely
wide dynamic range input currents to a much narrower
range. Wide input dynamic ranges of 8 decades, or
100pA to 10mA, can be accommodated for input to a
12-bit ADC. (Suggested products: LOG101, LOG102,
LOG104, and LOG112.)
ADS8411 values may vary for other ADCs.
Figure 12. Driving 16-Bit ADCs
CF
RF
Extremely small currents can be accurately measured
by integrating currents on a capacitor. (Suggested
product: IVC102.)
R1
Low-level currents can be converted to high-resolution
data words. (Suggested product: DDC112.)
VIN
OPA380
VOUT
For further information on the range of products
available, search www.ti.com using the above specific
model names or by using keywords transimpedance
and logarithmic.
(Provides high−speed amplification
with very low offset and drift.)
Figure 13. OPA380 Inverting Gain Configuration
14
PACKAGE OPTION ADDENDUM
www.ti.com
16-Aug-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
OPA2380AIDGKR
OPA2380AIDGKRG4
OPA2380AIDGKT
OPA2380AIDGKTG4
OPA380AID
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
DGK
D
8
8
8
8
8
8
8
8
8
8
8
8
2500
2500
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAUAGLevel-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
75
Green (RoHS
& no Sb/Br)
OPA380AIDG4
SOIC
D
75
Green (RoHS
& no Sb/Br)
OPA380AIDGKR
OPA380AIDGKRG4
OPA380AIDGKT
OPA380AIDGKTG4
OPA380AIDR
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
DGK
D
2500
2500
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
2500
2500
Green (RoHS
& no Sb/Br)
OPA380AIDRG4
SOIC
D
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
16-Aug-2012
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
OPA2380AIDGKR
OPA2380AIDGKT
OPA380AIDGKR
OPA380AIDGKT
OPA380AIDR
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
DGK
D
8
8
8
8
8
2500
250
330.0
180.0
330.0
180.0
330.0
12.4
12.4
12.4
12.4
12.4
5.3
5.3
5.3
5.3
6.4
3.4
3.4
3.4
3.4
5.2
1.4
1.4
1.4
1.4
2.1
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
2500
250
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA2380AIDGKR
OPA2380AIDGKT
OPA380AIDGKR
OPA380AIDGKT
OPA380AIDR
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
DGK
D
8
8
8
8
8
2500
250
367.0
210.0
367.0
210.0
367.0
367.0
185.0
367.0
185.0
367.0
35.0
35.0
35.0
35.0
35.0
2500
250
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明