OPA2830IDGKT [TI]
Dual, Low-Power, Single-Supply, Wideband OPERATIONAL AMPLIFIER;
| 型号： | OPA2830IDGKT |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Dual, Low-Power, Single-Supply, Wideband OPERATIONAL AMPLIFIER 放大器 光电二极管 |
| 文件： | 总43页 (文件大小：1063K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
Dual, Low-Power, Single-Supply, Wideband
OPERATIONAL AMPLIFIER
1
FEATURES
DESCRIPTION
2
•
HIGH BANDWIDTH:
The OPA2830 is a dual, low-power, single-supply,
wideband, voltage-feedback amplifier designed to
operate on a single +3V or +5V supply. Operation on
±5V or +10V supplies is also supported. The input
range extends below ground and to within 1.8V of the
230MHz (G = +1), 100MHz (G = +2)
•
•
LOW SUPPLY CURRENT: 7.8mA (VS = +5V)
FLEXIBLE SUPPLY RANGE:
±1.5V to ±5.5V Dual Supply
+3V to +11V Single Supply
positive
supply.
Using
complementary
common-emitter outputs provides an output swing to
within 25mV of ground and +VS while driving 150Ω.
High output drive current (75mA) and low differential
gain and phase errors also make it ideal for
single-supply consumer video products.
•
INPUT RANGE INCLUDES GROUND ON
SINGLE SUPPLY
•
•
•
•
4.82VPP OUTPUT SWING ON +5V SUPPLY
HIGH SLEW RATE: 500V/µs
Low distortion operation is ensured by the high gain
bandwidth product (100MHz) and slew rate
(500V/µs), making the OPA2830 an ideal input buffer
stage to 3V and 5V CMOS Analog-to-Digital
Converters (ADCs). Unlike earlier low-power,
single-supply amplifiers, distortion performance
improves as the signal swing is decreased. A low
9.2nV/√Hz input voltage noise supports wide dynamic
range operation.
LOW INPUT VOLTAGE NOISE: 9.2nV/√Hz
AVAILABLE IN AN MSOP-8 PACKAGE
APPLICATIONS
•
•
•
•
•
•
•
SINGLE-SUPPLY ADC INPUT BUFFERS
SINGLE-SUPPLY VIDEO LINE DRIVERS
CCD IMAGING CHANNELS
LOW-POWER ULTRASOUND
PLL INTEGRATORS
The OPA2830 is available in an industry-standard
SO-8 package. The OPA2830 is also available in a
small MSOP-8 package. For fixed-gain and line driver
applications, consider the OPA2832.
PORTABLE CONSUMER ELECTRONICS
LOW-POWER ACTIVE FILTERS
150pF
RELATED PRODUCTS
+5V
DESCRIPTION
SINGLES
DUALS
TRIPLES
QUADS
OPA4830
—
µ
0.1
F
Ω
Ω
506
238
Rail-to-Rail
OPA830
—
—
1/2
OPA2830
Rail-to-Rail Fixed-Gain
OPA832 OPA2832 OPA3832
OPA690 OPA2690 OPA3690
+5V
General-Purpose
(1800V/s slew rate)
—
100pF
Ω
238
Ω
750
Low-Noise,
High DC Precision
Ω
5k
5k
OPA820 OPA2822
—
OPA4820
2.5V
0.1
VI
BUF602
Ω
1500
VO
µ
F
Ω
Ω
750
100pF
Ω
238
1/2
OPA2830
µ
0.1
F
Ω
Ω
506
238
150pF
Single-Supply, Differential, 2nd-Order, 5MHz, Low-Pass Sallen-Key Filter
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2008, Texas Instruments Incorporated
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
SPECIFIED
PACKAGE
DESIGNATOR
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
PACKAGE-LEAD
OPA2830ID
OPA2830IDR
OPA2830IDGKT
Rails, 100
OPA2830
SO-8 Surface-Mount
D
–40°C to +85°C
–40°C to +85°C
OPA2830
A59
Tape and Reel, 2500
Tape and Reel, 250
OPA2830
MSOP-8
DGK
OPA2830IDGKR Tape and Reel, 2500
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS(1)
Power Supply
11VDC
Internal Power Dissipation
Differential Input Voltage
Input Voltage Range
See Thermal Characteristics
±2.5V
–0.5V to +VS + 0.3V
–65°C to +125°C
+300°C
Storage Temperature Range: D, DGK
Lead Temperature (soldering, 10s)
Junction Temperature (TJ)
ESD Rating:
+150°C
Human Body Model (HBM)
Charge Device Model (CDM)
Machine Model (MM)
2000V
1000V
200V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not supported.
PIN CONFIGURATIONS
Top View
SO, MSOP
Output 1
1
2
3
4
8
7
6
5
+VS
−
Input
Output 2
1
−
Input 2
+Input 1
−
VS
+Input 2
2
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
ELECTRICAL CHARACTERISTICS: VS = ±5V
Boldface limits are tested at +25C.
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 70).
OPA2830ID, IDGK
MIN/MAX OVER
TYP
TEMPERATURE
0°C to
–40°C to
MIN/
MAX
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1) +70°C(2) +85°C(2)
UNITS
LEVEL(3)
AC PERFORMANCE (see Figure 70)
Small-Signal Bandwidth
G = +1, VO ≤ 0.2VPP
G = +2, VO ≤ 0.2VPP
G = +5, VO ≤ 0.2VPP
G = +10, VO ≤ 0.2VPP
G ≥ +10
290
105
22
MHz
MHz
MHz
MHz
MHz
dB
typ
min
min
min
min
typ
C
B
B
B
B
C
B
B
B
B
66
16
8
64
14
7
61
13
6
10
Gain Bandwidth Product
Peaking at a Gain of +1
Slew Rate
100
4
80
77
75
VO ≤ 0.2VPP
G = +2, 2V Step
0.5V Step
560
3.4
3.6
43
275
5.9
6.0
64
265
5.95
6.05
66
255
6.0
6.1
67
V/µs
ns
min
max
max
max
Rise Time
Fall Time
0.5V Step
ns
Settling Time to 0.1%
Harmonic Distortion
2nd-Harmonic
G = +2, 1V Step
VO = 2VPP, f = 5MHz
RL = 150Ω
ns
–62
–66
–59
–77
9.5
–55
–58
–50
–65
10.6
4.8
–53
–57
–49
–62
11.1
5.3
–52
–56
–48
–55
11.6
5.8
dBc
dBc
min
min
min
min
max
max
typ
B
B
B
B
B
B
C
C
R
L ≥ 500Ω
RL = 150Ω
L ≥ 500Ω
3rd-Harmonic
dBc
R
dBc
Input Voltage Noise
Input Current Noise
NTSC Differential Gain
NTSC Differential Phase
DC PERFORMANCE(4)
Open-Loop Voltage Gain
Input Offset Voltage
Average Offset Voltage Drift
Input Bias Current
f > 1MHz
f > 1MHz
nV/√Hz
pA/√Hz
%
3.7
0.07
0.17
°
typ
RL = 150Ω
74
±1.5
—
66
65
±8.7
±27
+12
±44
±1.3
±5
64
±9.3
±27
+13
±46
±1.5
±6
dB
mV
min
max
max
max
max
max
max
A
A
B
A
B
A
B
±7.5
µV/°C
µA
VCM = 2.0V
VCM = 2.0V
+5
+10
Input Bias Current Drift
Input Offset Current
Input Offset Current Drift
INPUT
nA/°C
µA
±0.2
—
±1.1
nA/°C
Negative Input Voltage
Positive Input Voltage
Common-Mode Rejection Ratio (CMRR)
Input Impedance
–5.5
3.2
80
–5.4
3.1
76
–5.3
3.0
74
–5.2
2.9
71
V
V
max
min
min
A
A
A
Input-Referred
dB
Differential Mode
10 || 2.1
kΩ || pF
kΩ || pF
typ
typ
C
C
Common-Mode
400 || 1.2
OUTPUT
Output Voltage Swing
G = +2, RL = 1kΩ to GND
G = +2, RL = 150Ω to GND
±4.88
±4.64
±82
±4.86
±4.60
±63
±4.85
±4.58
±58
±4.84
±4.56
±53
V
V
min
min
min
typ
A
A
A
C
C
Current Output, Sinking and Sourcing
Short-Circuit Current
mA
mA
Ω
Output Shorted to Ground
150
Closed-Loop Output Impedance
G = +2, f ≤ 100kHz
0.06
typ
(1) Junction temperature = ambient for +25°C specifications.
(2) Junction temperature = ambient at low temperature limits; junction temperature = ambient +18°C at high temperature limit for over
temperature specifications.
(3) Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
(4) Current is considered positive out of pin.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±5V (continued)
Boldface limits are tested at +25C.
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 70).
OPA2830ID, IDGK
MIN/MAX OVER
TYP
TEMPERATURE
0°C to
–40°C to
MIN/
MAX
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1) +70°C(2) +85°C(2)
UNITS
LEVEL(3)
POWER SUPPLY
Minimum Operating Voltage
Maximum Operating Voltage
Maximum Quiescent Current
Minimum Quiescent Current
Power-Supply Rejection Ratio (–PSRR)
THERMAL CHARACTERISTICS
Specification: ID, IDGK
±1.4
V
typ
max
max
min
min
C
A
A
A
A
±5.5
9.5
8.0
61
±5.5
10.7
7.2
±5.5
11.9
6.6
V
VS = ±5V, Both Channels
VS = ±5V, Both Channels
Input-Referred
8.5
8.5
66
mA
mA
dB
60
59
–40 to +85
°C
typ
C
Thermal Resistance, θJA
D
SO-8
125
150
°C/W
°C/W
typ
typ
C
C
DGK
MSOP-8
4
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
ELECTRICAL CHARACTERISTICS: VS = +5V
Boldface limits are tested at +25°C.
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to VS/2, unless otherwise noted (see Figure 72).
OPA2830ID, IDGK
TYP
MIN/MAX OVER TEMPERATURE
0°C to
–40°C to
+85°C(2)
MIN/
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1)
+70°C(2)
UNITS
MAX LEVEL(3)
AC PERFORMANCE (see Figure 72)
Small-Signal Bandwidth
G = +1, VO ≤ 0.2VPP
G = +2, VO ≤ 0.2VPP
G = +5, VO ≤ 0.2VPP
G = +10, VO ≤ 0.2VPP
G ≥ +10
230
100
21
MHz
MHz
MHz
MHz
MHz
dB
typ
min
min
min
min
typ
C
B
B
B
B
C
B
B
B
B
70
15
7
68
14
6
66
13
5
10
Gain-Bandwidth Product
Peaking at a Gain of +1
Slew Rate
100
4
75
65
59
VO ≤ 0.2VPP
G = +2, 2V Step
0.5V Step
500
3.4
3.4
44
270
5.8
5.8
65
260
5.9
5.9
67
250
6.0
6.0
68
V/µs
ns
min
max
max
max
Rise Time
Fall Time
0.5V Step
ns
Settling Time to 0.1%
Harmonic Distortion
2nd-Harmonic
G = +2, 1V Step
VO = 2VPP, f = 5MHz
RL = 150Ω
ns
–58
–62
–52
–56
–50
–65
10.3
4.6
–51
–55
–49
–62
10.8
5.1
–50
–54
–48
–60
11.3
5.6
dBc
dBc
min
min
min
min
max
max
typ
B
B
B
B
B
B
C
C
R
L ≥ 500Ω
RL = 150Ω
L ≥ 500Ω
3rd-Harmonic
–58
dBc
R
–84
dBc
Input Voltage Noise
f > 1MHz
f > 1MHz
9.2
nV/√Hz
pA/√Hz
%
Input Current Noise
3.5
NTSC Differential Gain
NTSC Differential Phase
DC PERFORMANCE(4)
Open-Loop Voltage Gain
Input Offset Voltage
0.075
0.087
°
typ
RL = 150Ω
72
±0.5
—
66
65
±6.5
±22
+12
±44
±1.1
±5
64
±7.0
±22
+13
±46
±1.3
±6
dB
mV
min
max
max
max
max
max
max
A
A
B
A
B
A
B
±5.5
Average Offset Voltage Drift
Input Bias Current
µV/°C
µA
VCM = 2.5V
VCM = 2.5V
+5
+10
Input Bias Current Drift
Input Offset Current
nA/°C
µA
±0.2
—
±0.9
Input Offset Current Drift
INPUT
nA/°C
Least Positive Input Voltage
Most Positive Input Voltage
Common-Mode Rejection Ratio (CMRR)
Input Impedance, Differential Mode
Common-Mode
–0.5
3.2
–0.4
3.1
76
–0.3
3.0
74
–0.2
2.9
71
V
V
max
min
min
typ
A
A
A
C
C
Input-Referred
80
dB
10 || 2.1
400 || 1.2
kΩ || pF
kΩ || pF
typ
OUTPUT
Least Positive Output Voltage
G = +5, RL = 1kΩ to 2.5V
G = +5, RL = 150Ω to 2.5V
G = +5, RL = 1kΩ to 2.5V
G = +5, RL = 150Ω to 2.5V
0.09
0.21
4.91
4.78
±75
0.11
0.24
4.89
4.75
±58
0.12
0.25
4.88
4.73
±53
0.13
0.26
4.87
4.72
±50
V
V
max
max
min
min
min
typ
A
A
A
A
A
C
C
Most Positive Output Voltage
V
V
Current Output, Sinking and Sourcing
Short-Circuit Output Current
mA
mA
Ω
Output Shorted to Either Supply
140
Closed-Loop Output Impedance
G = +2, f ≤ 100kHz
0.06
typ
(1) Junction temperature = ambient for +25°C specifications.
(2) Junction temperature = ambient at low temperature limits; junction temperature = ambient +6°C at high temperature limit for over
temperature specifications.
(3) Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
(4) Current is considered positive out of pin.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
ELECTRICAL CHARACTERISTICS: VS = +5V (continued)
Boldface limits are tested at +25°C.
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to VS/2, unless otherwise noted (see Figure 72).
OPA2830ID, IDGK
TYP
MIN/MAX OVER TEMPERATURE
0°C to
–40°C to
+85°C(2)
MIN/
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1)
+70°C(2)
UNITS
MAX LEVEL(3)
POWER SUPPLY
Minimum Operating Voltage
Maximum Operating Voltage
Maximum Quiescent Current
Minimum Quiescent Current
Power-Supply Rejection Ratio (PSRR)
THERMAL CHARACTERISTICS
Specification: ID, IDGK
+2.8
V
min
max
max
min
min
B
A
A
A
A
+11
8.3
7.4
61
+11
9.7
6.8
60
+11
11.1
6.2
V
VS = +5V, Both Channels
VS = +5V, Both Channels
Input-Referred
7.8
7.8
66
mA
mA
dB
59
–40 to +85
°C
typ
C
Thermal Resistance, θJA
D
SO-8
125
150
°C/W
°C/W
typ
typ
C
C
DGK
MSOP-8
6
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
ELECTRICAL CHARACTERISTICS: VS = +3V
Boldface limits are tested at +25C.
At TA = +25°C, G = +2V/V, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 71).
OPA2830ID, IDGK
MIN/MAX OVER
TYP
TEMPERATURE
0°C to
MIN/
MAX
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1)
+70°C(2)
UNITS
LEVEL(3)
AC PERFORMANCE (see Figure 71)
Small-Signal Bandwidth
G = +2, VO ≤ 0.2VPP
G = +5, VO ≤ 0.2VPP
G = +10, VO ≤ 0.2VPP
G ≥ +10
90
20
9
70
15
66
14
MHz
MHz
MHz
MHz
V/µs
ns
min
min
min
min
min
max
max
max
B
B
B
B
B
B
B
B
7.5
75
6.5
65
Gain-Bandwidth Product
Slew Rate
90
220
3.4
3.4
46
1V Step
135
5.6
5.6
73
105
5.7
5.7
88
Rise Time
0.5V Step
Fall Time
0.5V Step
ns
Settling Time to 0.1%
Harmonic Distortion
2nd-Harmonic
1V Step
ns
VO = 1VPP, f = 5MHz
RL = 150Ω
–60
–64
–68
–72
9.2
–56
–59
–59
–65
10.3
4.6
–54
–57
–58
–64
10.8
5.1
dBc
dBc
min
min
min
min
max
max
B
B
B
B
B
B
R
L ≥ 500Ω
RL = 150Ω
L ≥ 500Ω
3rd-Harmonic
dBc
R
dBc
Input Voltage Noise
f > 1MHz
f > 1MHz
nV/√Hz
pA/√Hz
Input Current Noise
3.5
DC PERFORMANCE(4)
Open-Loop Voltage Gain
Input Offset Voltage
Average Offset Voltage Drift
Input Bias Current
72
±1.5
—
66
65
±8.7
±27
+12
±44
±1.3
±5
dB
mV
min
max
max
max
max
max
max
A
A
B
A
B
A
B
±7.5
µV/°C
µA
VCM = 1.0V
VCM = 1.0V
+5
+10
Input Bias Current Drift
Input Offset Current
Input Offset Current Drift
INPUT
nA/°C
µA
±0.2
—
±1.1
nA/°C
Least Positive Input Voltage
Most Positive Input Voltage
Common-Mode Rejection Ratio (CMRR)
Input Impedance
–0.45
1.2
–0.4
1.1
74
–0.27
1.0
V
V
max
min
min
A
A
A
Input-Referred
80
72
dB
Differential Mode
10 || 2.1
kΩ || pF
kΩ || pF
typ
typ
C
C
Common-Mode
400 || 1.2
OUTPUT
Least Positive Output Voltage
G = +5, RL = 1kΩ to 1.5V
G = +5, RL = 150Ω to 1.5V
G = +5, RL = 1kΩ to 1.5V
G = +5, RL = 150Ω to 1.5V
0.08
0.17
2.91
2.82
±30
45
0.11
0.39
2.88
2.74
±20
0.125
0.40
2.85
2.70
±18
V
V
max
max
min
min
min
typ
A
A
A
A
A
C
C
Most Positive Output Voltage
V
V
Current Output, Sinking and Sourcing
Short-Circuit Output Current
mA
mA
Ω
Output Shorted to Either Supply
See Figure 71, f < 100kHz
Closed-Loop Output Impedance
0.06
typ
(1) Junction temperature = ambient for +25°C specifications.
(2) Junction temperature = ambient at low temperature limits; junction temperature = ambient +20°C at high temperature limit for over
temperature specifications.
(3) Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
(4) Current is considered positive out of node.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
ELECTRICAL CHARACTERISTICS: VS = +3V (continued)
Boldface limits are tested at +25C.
At TA = +25°C, G = +2V/V, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 71).
OPA2830ID, IDGK
MIN/MAX OVER
TYP
TEMPERATURE
0°C to
MIN/
MAX
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1)
+70°C(2)
UNITS
LEVEL(3)
POWER SUPPLY
Minimum Operating Voltage
Maximum Operating Voltage
Maximum Quiescent Current
Minimum Quiescent Current
Power-Supply Rejection Ratio (PSRR)
THERMAL CHARACTERISTICS
Specification: ID, IDGK
+2.8
V
min
max
max
min
min
B
A
A
A
A
+11
8.1
6.6
60
+11
8.7
6.2
58
V
VS = +3V, Both Channels
VS = +3V, Both Channels
Input-Referred
7.4
7.4
64
mA
mA
dB
–40 to +85
°C
typ
C
Thermal Resistance, θJA
D
SO-8
125
150
°C/W
°C/W
typ
typ
C
C
DGK
MSOP-8
8
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = ±5V
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 72).
NONINVERTING SMALL-SIGNAL FREQUENCY RESPONSE
6
INVERTING SMALL-SIGNAL FREQUENCY RESPONSE
3
G = +1
−
G =
2
3
0
Ω
RF = 0
0
3
6
9
−
G =
1
−
−
−
G = +2
−
3
6
9
G = +5
−
G =
5
−
−
−
G = 10
G = +10
−
−
−
12
15
18
−
−
−
12
15
18
VO = 0.2VPP
VO = 0.2VPP
Ω
RL = 150
See Figure 72
Ω
RL = 150
1
10
100
400
1
10
100
600
Frequency (MHz)
Frequency (MHz)
Figure 1.
Figure 2.
NONINVERTING LARGE-SIGNAL
FREQUENCY RESPONSE
INVERTING LARGE-SIGNAL FREQUENCY RESPONSE
3
9
6
3
0
VO = 4VPP
0
VO = 2VPP
−
3
6
9
VO = 1VPP
VO = 0.5VPP
−
−
VO = 1VPP
−
−
−
3
6
9
VO = 4VPP
VO = 2VPP
−
−
−
12
15
18
G = +2V/V
−
G = 1V/V
Ω
RL = 150
See Figure 72
Ω
RL = 150
VO = 0.5VPP
−
12
10
100
400
10
100
400
Frequency (MHz)
Frequency (MHz)
Figure 3.
Figure 4.
NONINVERTING PULSE RESPONSE
INVERTING PULSE RESPONSE
0.4
2.0
1.5
1.0
0.5
0
0.4
0.3
0.2
0.1
0
2.0
1.5
1.0
0.5
0
G = +2V/V
See Figure 72
−
G = 1V/V
±
Large−Signal 1V
0.3
0.2
0.1
0
Right Scale
±
Small−Signal 100mV
±
Small−Signal 100mV
Left Scale
Left Scale
−
−
−
−
−
−
−
−
0.1
0.2
0.3
0.4
0.5
1.0
1.5
2.0
−
−
−
−
−
−
−
−
0.1
0.2
0.3
0.4
0.5
1.0
1.5
2.0
±
Large−Signal 1V
Right Scale
Time (10ns/div)
Time (10ns/div)
Figure 5.
Figure 6.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS: VS = ±5V (continued)
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 72).
HARMONIC DISTORTION vs LOAD RESISTANCE
5MHz HARMONIC DISTORTION vs SUPPLY VOLTAGE
40
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
50
55
60
65
70
75
80
85
G = +2V/V
VO = 2VPP
45
50
55
60
65
70
75
80
85
90
Input Limited for VCM = 0V
Ω
RL = 500
See Figure 72
2nd−Harmonic
2nd−Harmonic
G = +2V/V
VO = 2VPP
f = 5MHz
3rd−Harmonic
3rd−Harmonic
See Figure 72
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
100
1k
Ω
Resistance (
)
±
Supply Voltage ( VS)
Figure 7.
Figure 8.
HARMONIC DISTORTION vs OUTPUT VOLTAGE
HARMONIC DISTORTION vs FREQUENCY
−
−
−
−
−
−
−
−
−
−
55
60
65
70
75
80
85
90
95
50
G = +2V/V
G = +2V/V
O = 2VPP
3rd−Harmonic
2nd−Harmonic
−
−
−
−
−
−
−
−
−
55
60
65
70
75
80
85
90
95
Ω
RL = 500
V
Ω
RL = 150
f = 5MHz
See Figure 72
See Figure 72
2nd−Harmonic
Ω
RL = 500
2nd−Harmonic
Ω
RL = 150
3rd−Harmonic
3rd−Harmonic
Ω
RL = 500
−
−
100
105
0.1
1
10
0.1
1
10
Output Voltage Swing (VPP
)
Frequency (MHz)
Figure 9.
Figure 10.
TWO-TONE, 3RD-ORDER INTERMODULATION SPURIOUS
SUPPLY AND OUTPUT CURRENT vs TEMPERATURE
83
82
81
80
79
78
77
13
−
−
−
−
−
−
−
−
−
−
−
40
45
50
55
60
65
70
75
80
85
90
PI
1 /2
PO
Ω
50
OPA 28 30
20MHz
12
Ω
500
Ω
750
11
Ω
750
Output Current (sourcing)
10MHz
10
Output Current (sinking)
9
5MHz
8
Quiescent Current (total, both amplifiers)
7
−
−
−
−
−
2
26
20
14
8
6
−
−
25
50
0
25
50
75
100
125
Single−Tone Load Power (2dBm/div)
_
Ambient Temperature ( C)
Figure 11.
Figure 12.
10
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = ±5V (continued)
At TA = +25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to GND, unless otherwise noted (see Figure 72).
FREQUENCY RESPONSE vs CAPACITIVE LOAD
RECOMMENDED RS vs CAPACITIVE LOAD
8
7
6
5
4
3
2
1
0
120
110
100
90
CL = 10pF
0dB Peaking Targeted
CL = 100pF
CL = 1000pF
80
70
60
RS
CL
50
VI
1/2
VO
(1)
50Ω OPA2830
40
1kΩ
750Ω
−
1
2
3
30
NOTE: (1) 1kΩis optional.
Ω
750
−
−
20
10
1
10
100
1k
1
10
100
200
Capacitive Load (pF)
Frequency (MHz)
Figure 13.
OUTPUT SWING vs LOAD RESISTANCE
Figure 14.
OUTPUT VOLTAGE AND CURRENT LIMITATIONS
6
6
5
4
3
2
1
0
1W Internal
5
4
3
2
1
0
1
2
3
4
5
6
Power Limit
Output
Current Limit
Ω
RL = 500
Ω
RL = 50
G = +5V/V
Ω
RL = 100
±
= 5V
VS
−
−
−
−
−
−
−
1
2
3
4
5
6
−
−
−
−
−
Output
Current Limit
One Channel Only
1W Internal
Power Limit
10
100
1k
−
−
−
−
40
160
120
80
0
40
80
120
160
Ω
Resistance (
)
IO (mA)
Figure 15.
Figure 16.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS: VS = ±5V, Differential Configuration
At TA = +25°C, RF = 604Ω (as shown in Figure 17), and RL = 500Ω, unless otherwise noted.
DIFFERENTIAL SMALL-SIGNAL FREQUENCY RESPONSE
3
+5V
GD = 1
0
1/2
OPA2830
GD = 2
Ω
20
−
−
−
3
6
9
RG
RG
Ω
Ω
604
G
D = 5
RL
500
VO
VI
Ω
604
GD = 10
−
−
12
15
VO = 200mVPP
1/2
OPA2830
Ω
RL = 500
1
10
100
200
Ω
604
20Ω
GD
=
−5V
Frequency (MHz)
RG
Figure 17.
Figure 18.
DIFFERENTIAL LARGE-SIGNAL FREQUENCY RESPONSE
9
DIFFERENTIAL DISTORTION vs LOAD RESISTANCE
45
−
−
−
−
−
−
−
−
−
−
−
50
55
60
65
70
75
80
85
90
95
6
3rd−Harmonic
VO = 5VPP
3
GD = 2
VO = 4VPP
f = 5MHz
0
VO = 2VPP
−
−
−
3
6
9
VO = 1VPP
2nd−Harmonic
GD = 2
RL = 500
VO = 200mVPP
Ω
−
100
100
150
200
250
300
350
400
450
500
1
10
100
200
Ω
Resistance (
)
Frequency (MHz)
Figure 19.
Figure 20.
DIFFERENTIAL DISTORTION vs FREQUENCY
DIFFERENTIAL DISTORTION vs OUTPUT VOLTAGE
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
40
55
GD = 2
RL = 500
f = 5MHz
G
D = 2
60
65
70
75
80
85
90
95
Ω
VO = 4VPP
RL = 500
50
60
70
80
90
Ω
3rd−Harmonic
3rd−Harmonic
2nd−Harmonic
−
−
100
110
−
−
100
105
2nd−Harmonic
0.1
1
10
100
1
10
Frequency (MHz)
Output Voltage Swing (VPP)
Figure 21.
Figure 22.
12
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = +5V
At TA = +25°C, G = +2V/V, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 70).
NONINVERTING SMALL-SIGNAL FREQUENCY RESPONSE
INVERTING SMALL-SIGNAL FREQUENCY RESPONSE
6
3
G = +1
−
G =
2
Ω
F = 0
R
3
0
0
−
G =
1
−
3
6
9
G = +2
−
3
6
9
G = +5
−
−
−
G =
5
−
−
−
G = 10
G = +10
−
−
−
12
15
18
−
−
−
12
15
18
VO = 0.2VPP
VO = 0.2VPP
Ω
RL = 150
See Figure 84
Ω
RL = 150
See Figure 70
1
10
100
500
1
10
100
300
Frequency (MHz)
Frequency (MHz)
Figure 23.
Figure 24.
NONINVERTING LARGE-SIGNAL
FREQUENCY RESPONSE
INVERTING LARGE-SIGNAL FREQUENCY RESPONSE
9
6
3
0
3
VO = 1VPP
VO = 2VPP
0
−
3
6
9
VO = 0.5VPP
−
−
VO = 0.5VPP
VO = 1VPP
−
−
−
3
6
9
−
−
−
12
15
18
VO = 2VPP
G = +2V/V
−
G = 1V/V
Ω
RL = 150
Ω
RL = 150
See Figure 84
See Figure 70
−
12
10
100
400
10
100
300
Frequency (MHz)
Frequency (MHz)
Figure 25.
Figure 26.
NONINVERTING PULSE RESPONSE
INVERTING PULSE RESPONSE
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.2
2.1
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.2
2.1
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
−
G = 1V/V
Large−Signal 1.5V to 3.5V
Right Scale
Small−Signal 2.4V to 2.6V
Left Scale
Small−Signal 2.4V to 2.6V
Left Scale
Large−Signal 1.5V to 3.5V
Right Scale
G = +2V/V
See Figure 70
Time (10ns/div)
Time (10ns/div)
Figure 27.
Figure 28.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS: VS = +5V (continued)
At TA = +25°C, G = +2V/V, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 70).
HARMONIC DISTORTION vs LOAD RESISTANCE
HARMONIC DISTORTION vs FREQUENCY
−
−
−
−
−
−
−
−
−
−
−
45
50
55
60
65
70
75
80
85
90
95
−
−
−
−
−
−
−
−
−
50
55
60
65
70
75
80
85
90
G = +2V/V
O = 2VPP
See Figure 70
V
2nd−Harmonic
2nd−Harmonic
2nd−Harmonic
3rd−Harmonic
Ω
RL = 150
Ω
RL = 500
3rd−Harmonic
G = +2V/V
VO = 2VPP
f = 5MHz
Ω
RL = 500
3rd−Harmonic
Ω
RL = 150
See Figure 70
−
100
100
1k
0.1
1
10
Ω
Load Resistance (
)
Frequency (MHz)
Figure 29.
Figure 30.
HARMONIC DISTORTION vs OUTPUT VOLTAGE
HARMONIC DISTORTION vs NONINVERTING GAIN
−
45
50
55
−
55
60
65
70
75
80
85
90
G = +2V/V
−
Ω
RL = 500
Input Limited
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
f = 5MHz
2nd−Harmonic
60 See Figure 70
2nd−Harmonic
65
70
75
80
85
90
95
3rd−Harmonic
Ω
RL = 500
VO = 2VPP
f = 5MHz
See Figure 70
3rd−Harmonic
−
100
1
10
0.1
1
10
Gain (V/V)
Output Voltage Swing (VPP
)
Figure 31.
Figure 32.
HARMONIC DISTORTION vs INVERTING GAIN
TWO-TONE, 3RD-ORDER INTERMODULATION SPURIOUS
−
55
60
65
70
75
80
85
−
−
−
−
−
−
−
−
−
−
−
45
50
55
60
65
70
75
80
85
90
95
PI
1 /2
PO
Ω
50
OP A28 30
20MHz
10MHz
−
Ω
500
Ω
750
2nd−Harmonic
−
−
−
−
−
Ω
750
5MHz
Ω
RL = 500
3rd−Harmonic
VO = 2VPP
f = 5MHz
1
10
−
−
−
−
−
−
−
−
−
−
−
−
−
2
26 24 22 20 18 16 14 12 10
8
6
4
Gain ( V/V )
Single−Tone Load Power (dBm)
Figure 33.
Figure 34.
14
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = +5V (continued)
At TA = +25°C, G = +2V/V, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 70).
INPUT VOLTAGE AND CURRENT NOISE DENSITY
100
CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY
100
10
1
Voltage Noise
√
(9.2nV/ Hz)
10
0.1
0.01
Current Noise
√
(3.5pA/ Hz)
1
1k
10k
100k
1M
10M
100M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
Figure 35.
Figure 36.
RECOMMENDED RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
8
7
6
5
4
3
2
1
0
130
CL = 10pF
< 0.5dB Peaking Targeted
120
110
100
90
CL = 100pF
CL = 1000pF
80
70
60
RS
CL
VI
1/2
OPA2830
50
VO
(1)
Ω
50
1kΩ
40
750Ω
−
−
−
1
2
3
30
NOTE: (1) 1kΩis optional.
750Ω
20
10
1
10
100
1k
1
10
100
300
Capacitive Load (pF)
Frequency (MHz)
Figure 37.
Figure 38.
OPEN-LOOP GAIN AND PHASE
VOLTAGE RANGES vs TEMPERATURE
80
70
60
50
40
30
20
10
0
180
160
140
120
100
80
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
Most Positive Output Voltage
20 log (AOL
)
Most Positive Input Voltage
Ω
RL = 150
(AOL
)
60
40
Least Positive Output Voltage
20
−
−
10
0
−
−
0.5
Least Positive Input Voltage
50 110
−
20
100
20
1.0
−
1k
10k
100k
1M
10M
100M
1G
50
0
Frequency (Hz)
_
Ambient Temperature (10 C/div)
Figure 39.
Figure 40.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS: VS = +5V (continued)
At TA = +25°C, G = +2V/V, RF = 750Ω, RL = 150Ω to VS/2, and input VCM = 2.5V, unless otherwise noted (see Figure 70).
TYPICAL DC DRIFT OVER TEMPERATURE
SUPPLY AND OUTPUT CURRENT vs TEMPERATURE
4
3
2
1
0
1
2
3
4
8
6
4
2
0
−
−
−
−
100
95
90
85
80
75
70
65
60
10.5
Input Bias Current (IB)
10.0
Quiescent Current
9.5
9.0
×
10 Input Offset Current (IOS
)
Output Current, Sinking
8.5
−
−
−
−
2
4
6
8
8.0
Output Current, Sourcing
7.5
Input Offset Voltage (VOS
)
7.0
6.5
−
−
−
−
25
50
25
0
25
50
75
100
125
50
0
25
50
75
100
125
_
_
Ambient Temperature ( C)
Ambient Temperature ( C)
Figure 41.
Figure 42.
CMRR AND PSRR vs FREQUENCY
OUTPUT SWING vs LOAD RESISTANCE
90
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
80
70
60
50
40
30
20
10
0
CMRR
G = +5V/V
PSRR
−
0.5
1k
10k
100k
1M
10M
100M
10
100
1k
Ω
Load Resistance ( )
Frequency (Hz)
Figure 43.
Figure 44.
16
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = +5V, Differential Configuration
At TA = +25°C, RF = 604Ω, and RL = 500Ω differential (as shown in Figure 45), unless otherwise noted.
DIFFERENTIAL SMALL-SIGNAL FREQUENCY RESPONSE
3
+5V
GD = 1
GD = 2
0
Ω
Ω
1.2k
2.5V
1/2
OPA2830
−
−
−
3
6
9
µ
1.2k
0.1
F
RG
Ω
Ω
604
G
D = 5
RL
VO
VI
GD = 10
RG
604
−
−
12
15
VO = 200mVPP
Ω
RL = 500
1/2
OPA2830
1
10
100
200
Ω
604
RG
GD
=
2.5V
Frequency (MHz)
Figure 45.
Figure 46.
DIFFERENTIAL LARGE-SIGNAL FREQUENCY RESPONSE
9
DIFFERENTIAL DISTORTION vs LOAD RESISTANCE
40
−
−
−
−
−
−
−
−
−
−
−
45
50
55
60
65
70
75
80
85
90
6
3rd−Harmonic
VO = 3VPP
3
VO = 2VPP
GD = 2
VO = 4VPP
f = 5MHz
0
−
−
−
3
6
9
VO = 1VPP
GD = 2
RL = 500
VO = 0.2VPP
2nd−Harmonic
Ω
100
150
200
250
300
350
400
450
500
1
10
100
200
Ω
Resistance (
)
Frequency (MHz)
Figure 47.
Figure 48.
DIFFERENTIAL DISTORTION vs FREQUENCY
DIFFERENTIAL DISTORTION vs OUTPUT VOLTAGE
−
−
−
−
−
−
−
−
30
40
50
60
70
80
90
55
GD = 2
RL = 500
f = 5MHz
G
D = 2
Ω
−
−
−
−
−
−
−
−
60
65
70
75
80
85
90
95
VO = 4VPP
RL = 500
3rd−Harmonic
2nd−Harmonic
Ω
3rd−Harmonic
2nd−Harmonic
−
100
110
−
−
100
1
10
100
1
10
Frequency (MHz)
Output Voltage Swing (VPP)
Figure 49.
Figure 50.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS: VS = +3V
At TA = +25°C, G = +2V/V, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 71).
NONINVERTING SMALL-SIGNAL FREQUENCY RESPONSE
INVERTING SMALL-SIGNAL FREQUENCY RESPONSE
6
3
G = +1
3
0
RF = 0
0
−
G =
G =
1
−
−
−
3
6
9
−
−
2
3
6
9
G = +2
G = +5
−
−
−
G =
5
−
−
−
12
15
18
−
−
−
12
15
18
−
G = 10
Ω
RL = 150
G = +10
Ω
RL = 150
VO = 0.2VPP
See Figure 71
VO = 0.2VPP
1
10
100
400
1
10
100
300
Frequency (MHz)
Frequency (MHz)
Figure 51.
Figure 52.
NONINVERTING LARGE-SIGNAL
FREQUENCY RESPONSE
INVERTING LARGE-SIGNAL FREQUENCY RESPONSE
3
9
6
3
0
0
VO = 1VPP
−
3
6
9
VO = 1VPP
VO = 0.5VPP
VO = 0.5VPP
−
−
VO = 1.5VPP
−
−
−
3
6
9
VO = 1.5VPP
−
−
−
12
15
18
G = +2V/V
−
G = 1V/V
Ω
RL = 150
Ω
RL = 150
See Figure 71
−
12
10
100
300
10
100
300
Frequency (MHz)
Frequency (MHz)
Figure 53.
Figure 54.
NONINVERTING PULSE RESPONSE
INVERTING PULSE RESPONSE
1.20
1.15
1.10
1.05
1.00
0.95
0.90
0.85
0.80
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
1.20
1.15
1.10
1.05
1.00
0.95
0.90
0.85
0.80
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
−
G = 1V/V
Large−Signal 0.5V to 1.5V
Right Scale
Ω
RL = 150
Small−Signal
0.95V to 1.05V
Left Scale
Small−Signal 0.95V to 1.05V
Left Scale
G = +2V/V
Large−Signal 0.5V to 1.5V
Right Scale
See Figure 71
Time (10ns/div)
Time (10ns/div)
Figure 55.
Figure 56.
18
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = +3V (continued)
At TA = +25°C, G = +2V/V, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 71).
HARMONIC DISTORTION vs LOAD RESISTANCE
HARMONIC DISTORTION vs OUTPUT VOLTAGE
−
−
−
−
−
−
−
30
40
50
60
70
80
90
−
−
−
−
−
−
−
−
−
50
55
60
65
70
75
80
85
90
G = +2V/V
G = +2V/V
VO = 1VPP
Ω
RL = 500
2nd−Harmonic
f = 5MHz
f = 5MHz
See Figure 71
See Figure 71
Input Limited
2nd−Harmonic
3rd−Harmonic
3rd−Harmonic
100
1k
0.1
1
10
Ω
Resistance (
)
Output Voltage Swing (VPP
)
Figure 57.
Figure 58.
HARMONIC DISTORTION vs FREQUENCY
TWO-TONE, 3RD-ORDER INTERMODULATION SPURIOUS
−
55
60
65
70
75
80
85
90
95
−
−
−
−
−
−
−
−
−
−
−
−
40
45
50
55
60
65
70
75
80
85
90
95
PI
G = +2V/V
VO = 1VPP
See Figure 71
1/2
2nd−Harmonic
−
PO
50Ω O PA 2830
Ω
RL = 500
Ω
500
−
−
−
−
−
−
−
Ω
750
20MHz
750Ω
2nd−Harmonic
Ω
RL = 150
10MHz
3rd−Harmonic
RL = 150
Ω
3rd−Harmonic
5MHz
Ω
RL = 500
−
100
−
−
−
−
−
−
−
−
−
−
−
28
26
24
22
20
18
16
14
12
10
8
0.1
1
10
Frequency (MHz)
Single−Tone Load Power (dBm)
Figure 59.
Figure 60.
RECOMMENDED RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
190
170
150
130
110
90
8
7
6
5
4
3
2
1
0
1
2
3
CL = 10pF
< 0.5dB Peaking Targeted
CL = 100pF
CL = 1000pF
RS
VI
70
OPA2830
VO
(1)
50Ω
CL
1kΩ
Ω
750
50
−
NOTE: (1) 1kΩis optional.
750Ω
30
−
−
10
1
10
100
1k
1
10
100
200
Capacitive Load (pF)
Frequency (MHz)
Figure 61.
Figure 62.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS: VS = +3V (continued)
At TA = +25°C, G = +2V/V, and RL = 150Ω to VS/3, unless otherwise noted (see Figure 71).
OUTPUT SWING vs LOAD RESISTANCE
3.5
3.0
2.5
2.0
G = +5V/V
1.5
1.0
0.5
0
−
0.5
10
100
1k
Ω
Load Resistance (
)
Figure 63.
20
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = +3V, Differential Configuration
At TA = +25°C, RF = 604Ω, and RL = 500Ω differential (as shown in Figure 64), unless otherwise noted.
DIFFERENTIAL SMALL-SIGNAL FREQUENCY RESPONSE
3
+3V
0
Ω
2k
GD = 1
1V
1/2
−
−
−
3
6
9
1kΩ
0.1µF OPA2830
G
D = 2
RG
Ω
604
GD = 5
GD = 10
RL
VO
VI
RG
Ω
604
−
−
12
15
VO = 200mVPP
Ω
RL = 500
1/2
OPA2830
1
10
100
200
1V
604Ω
=
RG
GD
Frequency (MHz)
Figure 64.
Figure 65.
DIFFERENTIAL LARGE-SIGNAL FREQUENCY RESPONSE
9
DIFFERENTIAL DISTORTION vs LOAD RESISTANCE
40
−
−
−
−
−
−
−
−
−
−
−
45
50
55
60
65
70
75
80
85
90
6
3
3rd−Harmonic
VO = 2VPP
GD = 2
VO = 4VPP
f = 5MHz
0
VO = 1VPP
−
−
−
3
6
9
VO = 200mVPP
2nd−Harmonic
GD = 2
100
150
200
250
300
350
400
450
500
1
10
100
200
Ω
Resistance (
)
Frequency (MHz)
Figure 66.
Figure 67.
DIFFERENTIAL DISTORTION vs FREQUENCY
DIFFERENTIAL DISTORTION vs OUTPUT VOLTAGE
75
−
−
−
−
−
−
−
−
35
G
D = 2
GD = 2
RL = 500
f = 5MHz
VO = 2VPP
45
55
65
75
85
95
Ω
Ω
RL = 500
−
−
−
−
80
85
90
95
3rd−Harmonic
2nd−Harmonic
3rd−Harmonic
2nd−Harmonic
−
−
105
115
−
100
0.50
0.1
1
10
100
0.75
1.00
1.25
1.50
1.75
2.00
Output Voltage Swing (VPP
)
Frequency (MHz)
Figure 68.
Figure 69.
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
APPLICATIONS INFORMATION
high frequencies is 150Ω || 1500Ω. The 1.13kΩ and
2.26kΩ resistors at the noninverting input provide the
common-mode bias voltage. Their parallel
combination equals the DC resistance at the inverting
input (RF), reducing the DC output offset due to input
bias current.
WIDEBAND VOLTAGE-FEEDBACK
OPERATION
The OPA2830 is a unity-gain stable, very high-speed
voltage-feedback op amp designed for single-supply
operation (+3V to +10V). The input stage supports
input voltages below ground and to within 1.7V of the
positive supply. The complementary common-emitter
output stage provides an output swing to within 25mV
of ground and the positive supply. The OPA2830 is
compensated to provide stable operation with a wide
range of resistive loads.
VS = +3V
µ
6.8 F
+
µ
0.1 F
Ω
2.26k
Figure 70 shows the AC-coupled, gain of +2
configuration used for the +5V Specifications and
Typical Characteristic Curves. For test purposes, the
input impedance is set to 50Ω with a resistor to
ground. Voltage swings reported in the Electrical
Characteristics are taken directly at the input and
output pins. For the circuit of Figure 70, the total
effective load on the output at high frequencies is
150Ω || 1500Ω. The 1.5kΩ resistors at the
noninverting input provide the common-mode bias
voltage. Their parallel combination equals the DC
resistance at the inverting input (RF), reducing the DC
output offset due to input bias current.
µ
0.1
F
+1V
VIN
1/2
OPA2830
Ω
Ω
1.13k
53.6
VOUT
RL
150
Ω
RG
RF
Ω
750
+VS
3
Ω
750
+VS/3
Figure 71. AC-Coupled, G = +2, +3V Single-Supply
Specification and Test Circuit
VS = +5V
Figure 72 shows the DC-coupled, gain of +2, dual
power-supply circuit configuration used as the basis
of the ±5V Electrical Characteristics and Typical
Characteristics. For test purposes, the input
impedance is set to 50Ω with a resistor to ground and
the output impedance is set to 150Ω with a series
output resistor. Voltage swings reported in the
specifications are taken directly at the input and
output pins. For the circuit of Figure 72, the total
effective load will be 150Ω || 1.5kΩ. Two optional
components are included in Figure 72. An additional
resistor (348Ω) is included in series with the
noninverting input. Combined with the 25Ω DC
source resistance looking back towards the signal
generator, this gives an input bias current cancelling
resistance that matches the 375Ω source resistance
seen at the inverting input (see the DC Accuracy and
Offset Control section). In addition to the usual
power-supply decoupling capacitors to ground, a
0.01µF capacitor is included between the two
power-supply pins. In practical PC board layouts, this
optional capacitor will typically improve the
2nd-harmonic distortion performance by 3dB to 6dB.
µ
6.8 F
+
µ
0.1 F
Ω
1.5k
µ
0.1
F
2.5V
VIN
1/2
Ω
Ω
1.5k
53.6
VOUT
OPA2830
RL
150
Ω
RG
RF
Ω
750
+VS
2
Ω
750
+VS/2
Figure 70. AC-Coupled, G = +2, +5V Single-Supply
Specification and Test Circuit
Figure 71 shows the AC-coupled, gain of +2
configuration used for the +3V Specifications and
Typical Characteristic Curves. Voltage swings
reported in the Electrical Characteristics are taken
directly at the input and output pins. For the circuit of
Figure 71, the total effective load on the output at
22
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
DC LEVEL-SHIFTING
Figure 74 shows the general form of Figure 73 as a
+5V
DC-coupled noninverting amplifier that level-shifts the
µ
µ
F
0.1
F
6.8
+
input up to accommodate the desired output voltage
range. Given the desired signal gain (G), and the
amount VOUT needs to be shifted up (ΔVOUT) when
VIN is at the center of its range, the following
equations give the resistor values that produce the
desired performance. Assume that R4 is between
200Ω and 1.5kΩ.
Ω
50 Source
Ω
348
VIN
Ω
150
VO
1/2
OPA2830
Ω
50
•
•
•
•
NG = G + VOUT/VS
R1 = R4/G
R2 = R4/(NG – G)
R3 = R4/(NG – 1)
µ
0.01
RG
F
RF
Ω
750
Ω
750
where:
µ
6.8
µ
0.1 F
F
+
•
•
NG = 1 + R4/R3
VOUT = (G)VIN + (NG – G)VS
−
5V
Make sure that VIN and VOUT stay within the specified
input and output voltage ranges.
Figure 72. DC-Coupled, G = +2, Bipolar Supply
Specification and Test Circuit
+VS
R2
SINGLE-SUPPLY ADC INTERFACE
The ADC interface of Figure 73 shows a DC-coupled,
single-supply ADC driver circuit. Many systems are
now requiring +3V to +5V supply capability of both
the ADC and its driver. The OPA2830 provides
excellent performance in this demanding application.
Its large input and output voltage ranges and low
distortion support converters such as the ADS5203
shown in the figure on page 1. The input level-shifting
circuitry was designed so that VIN can be between 0V
and 0.5V, while delivering an output voltage of 1V to
2V for the ADS5203.
R1
VIN
1/2
OPA2830
VOUT
R3
R4
+3V
Figure 74. DC Level-Shifting
Ω
2.26k
+3V
The circuit of Figure 73 is a good example of this type
of application. It was designed to take VIN between
0V and 0.5V and produce VOUT between 1V and 2V
when using a +3V supply. This means G = 2.00, and
ΔVOUT = 1.50V – G
נ
0.25V = 1.00V. Plugging these values into the above equations (with R4 = 750Ω)
gives: NG = 2.33, R1 = 375Ω, R2 = 2.25kΩ, and R3 =
563Ω. The resistors were changed to the nearest
standard values for the circuit of Figure 73.
Ω
374
1/2
ADS5203
10−Bit
VIN
Ω
100
1/2
OPA2830
30MSPS
22pF
Ω
Ω
750
562
Figure 73. DC-Coupled, +3V ADC Driver
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
AC-COUPLED OUTPUT VIDEO LINE DRIVER
approximately –20dB, so good supply decoupling is
recommended on the power-supply pin. Figure 75
shows the frequency response for the circuit of
Figure 76. This plot shows the 8Hz low-frequency
high-pass pole and a high-end cutoff at approximately
100MHz.
Low-power and low-cost video line drivers often
buffer digital-to-analog converter (DAC) outputs with
a gain of 2 into a doubly-terminated line. Those
interfaces typically require a DC blocking capacitor.
For a simple solution, that interface often has used a
very large value blocking capacitor (220µF) to limit
tilt, or SAG, across the frames. One approach to
creating a very low high-pass pole location using
much lower capacitor values is shown in Figure 76.
This circuit gives a voltage gain of 2 at the output pin
with a high-pass pole at 8Hz. Given the 150Ω load, a
simple blocking capacitor approach would require a
133µF value. The two much lower valued capacitors
give this same low-pass pole using this simple SAG
correction circuit of Figure 76.
3
0
−
−
−
3
6
9
−
−
−
−
12
15
18
21
The input is shifted slightly positive in Figure 76 using
the voltage divider from the positive supply. This
gives about a 200mV input DC offset that will show
up at the output pin as a 400mV DC offset when the
DAC output is at zero current during the sync tip
portion of the video signal. This acts to hold the
output in its linear operating region. This will pass on
any power-supply noise to the output with a gain of
1
10
102 103 104 105 106 107 108 109
Frequency (Hz)
Figure 75. Video Line Driver Response to Matched
Load
+5V
Ω
1.87k
Video DAC
µ
47
F
Ω
75
1/2
VO
OPA2830
Ω
78.7
Ω
75 Load
µ
22
F
Ω
845
Ω
325
Ω
528
Ω
650
Figure 76. Video Line Driver with SAG Correction
24
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
NONINVERTING AMPLIFIER WITH REDUCED
PEAKING
SINGLE-SUPPLY ACTIVE FILTER
The OPA2830 operating on a single +3V or +5V
supply lends itself well to high-frequency active filter
designs. The key additional requirement is to
establish the DC operating point of the signal near
the supply midpoint for highest dynamic range.
Figure 78 shows an example design of a 1MHz
low-pass Butterworth filter using the Sallen-Key
topology.
Figure 77 shows a noninverting amplifier that reduces
peaking at low gains. The resistor RC compensates
the OPA2830 to have higher Noise Gain (NG), which
reduces the AC response peaking (typically 4dB at
G = +1 without RC) without changing the DC gain. VIN
needs to be a low impedance source, such as an op
amp.
Both the input signal and the gain setting resistor are
AC-coupled using 0.1µF blocking capacitors (actually
giving bandpass response with the low-frequency
pole set to 32kHz for the component values shown).
This allows the midpoint bias formed by the two
1.87kΩ resistors to appear at both the input and
output pins. The midband signal gain is set to +4
(12dB) in this case. The capacitor to ground on the
noninverting input is intentionally designed at a higher
value to dominate input parasitic terms. At a gain of
+4, the OPA2830 on a single supply will show 30MHz
small- and large-signal bandwidth. The filter resistor
values have been slightly adjusted to account for this
limited bandwidth in the amplifier stage. Tests of this
circuit show a precise 1MHz, –3dB point with a
+5V
RT
VIN
1/2
OPA2830
RC
VOUT
RG
RF
Figure 77. Compensated Noninverting Amplifier
The Noise Gain can be calculated as follows:
maximally-flat
passband
(above
the
32kHz
AC-coupling corner), and a maximum stop band
attenuation of 36dB at the amplifier's –3dB bandwidth
of 30MHz.
RF
G1 + 1 )
RG
R
F
RT ) G1
G2 + 1 )
RC
NG + G1 G2
A unity-gain buffer can be designed by selecting
RT = RF = 20.0Ω and RC = 40.2Ω (do not use RG).
This gives a noise gain of 2, so the response will be
similar to the Characteristics Plots with G = +2 giving
less peaking.
+5V
100pF
Ω
1.87k
µ
0.1
F
Ω
Ω
432
137
VI
1/2
4VI
OPA2830
150pF
Ω
1.87k
1MHz, 2nd−Order
Butterworth Filter
Ω
1.5k
Ω
500
µ
0.1
F
Figure 78. Single-Supply, High-Frequency Active Filter
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
Implementing the DC bias in this way also attenuates
the differential signal by half. This is recovered by
DIFFERENTIAL LOW-PASS ACTIVE FILTERS
The dual OPA2830 offers an easy means to
implement low-power differential active filters. On a
single supply, one way to implement a 2nd-order,
low-pass filter is shown in Figure 79. This circuit
provides a net differential gain of 1 with a precise
5MHz Butterworth response. The signal is
setting the amplifier gain at 2V/V to get a net
unity-gain filter characteristic from input to output. The
filter design shown here has also adjusted the
resistor values slightly from an ideal analysis to
account for the 100MHz bandwidth in the amplifier
stages. The filter capacitors at the noninverting inputs
are shown as two separate capacitors to ground.
While it is certainly correct to collapse these two
capacitors into a single capacitor across the two
inputs (which would be 50pF for this circuit) to get the
same differential filtering characteristic, tests have
shown two separate capacitors to a low impedance
point act to attenuate the common-mode feedback
present in this circuit giving more stable operation in
actual implementation. Figure 80 shows the
frequency response for the filter of Figure 79.
AC-coupled (giving
a
high-pass pole at low
frequencies) with the DC operating point for the
circuit set by the unity-gain buffer—the BUF602. This
buffer gives a very low output impedance to high
frequencies to maintain accurate filter characteristics.
If the source is a DC-coupled signal already biased
into the operating range of the OPA2830 input CMR,
these capacitors and the midpoint bias may be
removed. To get the desired 5MHz cutoff, the input
resistors to the filter is actually 119Ω. This is
implemented in Figure 79 as the parallel combination
of the two 238Ω resistors on each half of the
differential input as part of the DC biasing network. If
the BUF602 is removed, these resistors should be
collapsed back to a single 119Ω input resistor.
0
−
−
−
−
−
−
−
−
−
1
2
3
4
5
6
7
8
9
150pF
+5V
µ
0.1
F
238Ω
506Ω
−
−
−
10
11
12
1/2
OPA2830
+5V
100pF
Ω
238
102
103
104
105
106
750Ω
Frequency (Hz)
Ω
5k
5k
2.5V
0.1µF
VI
BUF602
Ω
1500
VO
Figure 80. 5MHz, 2nd-Order, Butterworth
Low-Pass Filter
Ω
Ω
750
100pF
150pF
Ω
238
1/2
OPA2830
µ
0.1
F
Ω
Ω
506
238
HIGH-PASS FILTERS
Another approach to mid-supply biasing is shown in
Figure 81. This method uses a bypassed divider
network in place of the buffer used in Figure 79. The
impedance is set by the parallel combination of the
resistors forming the divider network, but as
frequency increases it looks more and more like a
short due to the capacitor. Generally, the capacitor
value needs to be two to three orders of magnitude
greater than the filter capacitors shown for the circuit
to work properly.
Figure 79. Single-Supply, 2nd-Order, Low-Pass
Sallen-Key Filter
26
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
compliance voltage other than ground for operation,
the appropriate voltage level may be applied to the
noninverting input of the OPA2830. The DC gain for
+VS
+5V
this circuit is equal to RF. At high frequencies, the
Ω
374
DAC output capacitance (CD in Figure 83) will
produce a zero in the noise gain for the OPA2830
that may cause peaking in the closed-loop frequency
response. CF is added across RF to compensate for
2.2nF 2.2nF
1/2
OPA2830
this noise gain peaking. To achieve
a
flat
transimpedance frequency response, the pole in each
feedback network should be set to:
Ω
Ω
Ω
750
750
2k
µ
1
F
GBP
4pRFCD
1
+
Ǹ
VS/2
VI
VO
2pRFCF
Ω
2k
which will give
approximately:
a
cutoff frequency f–3dB of
1/2
2.2nF 2.2nF
OPA2830
GBP
2pRFCD
f
+
Ǹ
*3dB
Ω
374
+5V
Figure 81. 138kHz, 2nd-Order, High-Pass Filter
Ω
2.5k
Ω
2.5k
Results showing the frequency response for the
circuit of Figure 81 is shown in Figure 82.
1/2
OPA2830
VO = IO RF
High−Speed
DAC
3
0
RF1
CF1
CD1
IO
−
−
−
3
6
9
RF2
CF2
CD2
−
IO
+5V
−
12
0.01
1/2
OPA2830
0.1
Frequency (MHz)
1
10
Ω
2.5k
−
−
IO RF
VO
=
Ω
2.5k
→
Figure 82. Frequency Response for the Filter of
Figure 81
GBP Gain Bandwidth
Product (Hz) for the OPA2830
Figure 83. High-Speed DAC—Differential
Transimpedance Amplifier
HIGH-PERFORMANCE DAC
TRANSIMPEDANCE AMPLIFIER
High-frequency video Digital-to-Analog Converters
(DACs) can sometimes benefit from a low distortion
output amplifier to retain their SFDR performance into
real-world loads. Figure 83 shows a differential output
drive implementation. The diagram shows the signal
output current(s) connected into the virtual ground
summing junction(s) of the OPA2830, which is set up
as a transimpedance stage or I-V converter. If the
DAC requires that its outputs terminate to
a
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
DESIGN-IN TOOLS
A good rule of thumb is to target the parallel
combination of RF and RG (see Figure 72) to be less
than about 400Ω. The combined impedance RF || RG
interacts with the inverting input capacitance, placing
an additional pole in the feedback network, and thus
a zero in the forward response. Assuming a 2pF total
Demonstration Fixtures
Two printed circuit boards (PCBs) are available to
assist in the initial evaluation of circuit performance
using the OPA2830 in its two package options. Both
of these are offered free of charge as unpopulated
PCBs, delivered with a user's guide. The summary
information for these fixtures is shown in Table 1.
parasitic on the inverting node, holding RF || RG
<
400Ω will keep this pole above 200MHz. By itself, this
constraint implies that the feedback resistor RF can
increase to several kΩ at high gains. This is
acceptable as long as the pole formed by RF and any
parasitic capacitance appearing in parallel is kept out
of the frequency range of interest.
Table 1. Demonstration Fixtures by Package
ORDERING
NUMBER
LITERATURE
NUMBER
PRODUCT
OPA2830ID
PACKAGE
SO-8
In the inverting configuration, an additional design
consideration must be noted. RG becomes the input
resistor and therefore the load impedance to the
driving source. If impedance matching is desired, RG
may be set equal to the required termination value.
However, at low inverting gains, the resultant
feedback resistor value can present a significant load
to the amplifier output. For example, an inverting gain
of 2 with a 50Ω input matching resistor (= RG) would
require a 100Ω feedback resistor, which would
contribute to output loading in parallel with the
external load. In such a case, it would be preferable
to increase both the RF and RG values, and then
achieve the input matching impedance with a third
resistor to ground (see Figure 84). The total input
impedance becomes the parallel combination of RG
and the additional shunt resistor.
DEM-OPA-SO-2A
SBOU003
SBOU004
OPA2830IDGK
MSOP-8
DEM-OPA-MSOP-2A
The demonstration fixtures can be requested at the
Texas Instruments web site (www.ti.com) through the
OPA2830 product folder.
Macromodel and Applications Support
Computer simulation of circuit performance using
SPICE is often
a quick way to analyze the
performance of the OPA2830 and its circuit designs.
This is particularly true for video and RF amplifier
circuits where parasitic capacitance and inductance
can play a major role on circuit performance. A
SPICE model for the OPA2830 is available through
the TI web page (www.ti.com). The applications
department is also available for design assistance.
These models predict typical small signal AC,
transient steps, DC performance, and noise under a
wide variety of operating conditions. The models
include the noise terms found in the electrical
specifications of the data sheet. These models do not
attempt to distinguish between the package types in
their small-signal AC performance.
BANDWIDTH vs GAIN:
NONINVERTING OPERATION
Voltage-feedback op amps exhibit decreasing
closed-loop bandwidth as the signal gain is
increased. In theory, this relationship is described by
the Gain Bandwidth Product (GBP) shown in the
specifications. Ideally, dividing GBP by the
noninverting signal gain (also called the Noise Gain,
or NG) will predict the closed-loop bandwidth. In
practice, this only holds true when the phase margin
approaches 90°, as it does in high-gain
configurations. At low gains (increased feedback
factors), most amplifiers will exhibit a more complex
response with lower phase margin. The OPA2830 is
compensated to give a slightly peaked response in a
noninverting gain of 2 (see Figure 72). This results in
a typical gain of +2 bandwidth of 105MHz, far
exceeding that predicted by dividing the 105MHz
GBP by 2. Increasing the gain will cause the phase
margin to approach 90° and the bandwidth to more
closely approach the predicted value of (GBP/NG). At
a gain of +10, the 10MHz bandwidth shown in the
Electrical Characteristics agrees with that predicted
using the simple formula and the typical GBP of
105MHz.
OPERATING SUGGESTIONS
OPTIMIZING RESISTOR VALUES
Since the OPA2830 is
a
unity-gain stable,
voltage-feedback op amp, a wide range of resistor
values may be used for the feedback and gain setting
resistors. The primary limits on these values are set
by dynamic range (noise and distortion) and parasitic
capacitance considerations. For
unity-gain follower application, the feedback
connection should be made with a direct short.
a
noninverting
Below 200Ω, the feedback network will present
additional output loading which can degrade the
harmonic distortion performance of the OPA2830.
Above 1kΩ, the typical parasitic capacitance
(approximately 0.2pF) across the feedback resistor
may cause unintentional band limiting in the amplifier
response.
28
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
Frequency response in a gain of +2 may be modified
to achieve exceptional flatness simply by increasing
the noise gain to 3. One way to do this, without
affecting the +2 signal gain, is to add an 2.55kΩ
resistor across the two inputs, as shown in Figure 77.
A similar technique may be used to reduce peaking in
unity-gain (voltage follower) applications. For
example, by using a 750Ω feedback resistor along
with a 750Ω resistor across the two op amp inputs,
the voltage follower response will be similar to the
gain of +2 response of Figure 71. Further reducing
the value of the resistor across the op amp inputs will
further dampen the frequency response due to
increased noise gain. The OPA2830 exhibits minimal
bandwidth reduction going to single-supply (+5V)
operation as compared with ±5V. This minimal
reduction is because the internal bias control circuitry
retains nearly constant quiescent current as the total
supply voltage between the supply pins is changed.
signal channel input impedance. If input impedance
matching is desired (which is beneficial whenever the
signal is coupled through a cable, twisted pair, long
PC board trace, or other transmission line conductor),
RG may be set equal to the required termination value
and RF adjusted to give the desired gain. This is the
simplest approach and results in optimum bandwidth
and noise performance.
However, at low inverting gains, the resulting
feedback resistor value can present a significant load
to the amplifier output. For an inverting gain of 2,
setting RG to 50Ω for input matching eliminates the
need for RM but requires a 100Ω feedback resistor.
This configuration has the interesting advantage of
the noise gain becoming equal to 2 for a 50Ω source
impedance—the same as the noninverting circuits
considered above. The amplifier output will now see
the 100Ω feedback resistor in parallel with the
external load. In general, the feedback resistor should
be limited to the 200Ω to 1.5kΩ range. In this case, it
is preferable to increase both the RF and RG values,
as shown in Figure 84, and then achieve the input
matching impedance with a third resistor (RM) to
ground. The total input impedance becomes the
parallel combination of RG and RM.
INVERTING AMPLIFIER OPERATION
All of the familiar op amp application circuits are
available with the OPA2830 to the designer. See
Figure 84 for a typical inverting configuration where
the I/O impedances and signal gain from Figure 70
are retained in an inverting circuit configuration.
Inverting operation is one of the more common
requirements and offers several performance
benefits. It also allows the input to be biased at VS/2
without any headroom issues. The output voltage can
be independently moved to be within the output
voltage range with coupling capacitors, or bias
adjustment resistors.
The second major consideration, touched on in the
previous paragraph, is that the signal source
impedance becomes part of the noise gain equation
and hence influences the bandwidth. For the example
in Figure 84, the RM value combines in parallel with
the external 50Ω source impedance (at high
frequencies), yielding an effective driving impedance
of 50Ω || 57.6Ω = 26.8Ω. This impedance is added in
series with RG for calculating the noise gain. The
resulting noise gain is 2.87 for Figure 84, as opposed
to only 2 if RM could be eliminated as discussed
above. The bandwidth will therefore be lower for the
gain of –2 circuit of Figure 84 (NG = +2.87) than for
the gain of +2 circuit of Figure 70.
+5V
+
µ
0.1
µ
F
F
6.8
2RT
1.5k
Ω
The third important consideration in inverting amplifier
design is setting the bias current cancellation
resistors on the noninverting input (a parallel
combination of RT = 750Ω). If this resistor is set equal
to the total DC resistance looking out of the inverting
node, the output DC error, due to the input bias
currents, will be reduced to (Input Offset Current)
times RF. With the DC blocking capacitor in series
with RG, the DC source impedance looking out of the
inverting mode is simply RF = 750Ω for Figure 84. To
reduce the additional high-frequency noise introduced
by this resistor and power-supply feed-through, RT is
bypassed with a capacitor.
Ω
150
+VS
2
1/2
OPA2830
2RT
1.5k
µ
0.1
F
Ω
Ω
50 Source
RG
RF
µ
0.1
F
Ω
374
Ω
750
RM
57.6
Ω
Figure 84. AC-Coupled, G = –2 Example Circuit
In the inverting configuration, three key design
considerations must be noted. The first consideration
is that the gain resistor (RG) becomes part of the
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
OUTPUT CURRENT AND VOLTAGES
DISTORTION PERFORMANCE
The OPA2830 provides outstanding output voltage
capability. For the +5V supply, under no-load
conditions at +25°C, the output voltage typically
swings closer than 90mV to either supply rail.
The OPA2830 provides good distortion performance
into a 150Ω load. Relative to alternative solutions, it
provides exceptional performance into lighter loads
and/or operating on a single +3V supply. Generally,
until the fundamental signal reaches very high
frequency or power levels, the 2nd-harmonic will
dominate the distortion with a negligible 3rd-harmonic
component. Focusing then on the 2nd-harmonic,
increasing the load impedance improves distortion
directly. Remember that the total load includes the
feedback network; in the noninverting configuration
(see Figure 72) this is sum of RF + RG, while in the
inverting configuration, only RF needs to be included
in parallel with the actual load. Running differentially
suppresses the 2nd-harmonic, as shown in the
differential typical characteristic curves.
The minimum specified output voltage and current
specifications over temperature are set by worst-case
simulations at the cold temperature extreme. Only at
cold startup will the output current and voltage
decrease to the numbers shown in the ensured
tables. As the output transistors deliver power, their
junction temperatures will increase, decreasing their
VBEs (increasing the available output voltage swing)
and increasing their current gains (increasing the
available output current). In steady-state operation,
the available output voltage and current will always
be greater than that shown in the over-temperature
specifications, since the output stage junction
temperatures will be higher than the minimum
specified operating ambient.
NOISE PERFORMANCE
High slew rate, unity-gain stable, voltage-feedback op
amps usually achieve their slew rate at the expense
of a higher input noise voltage. The 9.2nV/√Hz input
voltage noise for the OPA2830 however, is much
lower than comparable amplifiers. The input-referred
voltage noise and the two input-referred current noise
terms (2.8pA/√Hz) combine to give low output noise
DRIVING CAPACITIVE LOADS
One of the most demanding and yet very common
load conditions for an op amp is capacitive loading.
Often, the capacitive load is the input of an
ADC—including additional external capacitance which
may be recommended to improve ADC linearity. A
high-speed, high open-loop gain amplifier like the
OPA2830 can be very susceptible to decreased
stability and closed-loop response peaking when a
capacitive load is placed directly on the output pin.
When the primary considerations are frequency
response flatness, pulse response fidelity, and/or
distortion, the simplest and most effective solution is
to isolate the capacitive load from the feedback loop
by inserting a series isolation resistor between the
amplifier output and the capacitive load.
under
a
wide variety of operating conditions.
Figure 85 shows the op amp noise analysis model
with all the noise terms included. In this model, all
noise terms are taken to be noise voltage or current
density terms in either nV/√Hz or pA/√Hz.
ENI
1/2
OPA2830
EO
RS
IBN
The Typical Characteristic curves show the
recommended RS versus capacitive load and the
resulting frequency response at the load. Parasitic
capacitive loads greater than 2pF can begin to
degrade the performance of the OPA2830. Long PC
board traces, unmatched cables, and connections to
multiple devices can easily exceed this value. Always
consider this effect carefully, and add the
recommended series resistor as close as possible to
the output pin (see the Board Layout Guidelines
section).
ERS
RF
√
4kTRS
√
4kTRF
IBI
RG
4kT
RG
−
K
4kT = 1.6E 20J
_
at 290
Figure 85. Noise Analysis Model
The total output spot noise voltage can be computed
as the square root of the sum of all squared output
noise voltage contributors. Equation 1 shows the
general form for the output noise voltage using the
terms shown in Figure 85:
The criterion for setting this RS resistor is a maximum
bandwidth, flat frequency response at the load. For a
gain of +2, the frequency response at the output pin
is already slightly peaked without the capacitive load,
requiring relatively high values of RS to flatten the
response at the load. Increasing the noise gain will
also reduce the peaking (see Figure 77).
2
2
2
2
) ǒ
SǓ
) ǒI FǓ
) 4kTR ǓNG
R ) 4kTR NG
BI
ǒE
Ǹ
E
+
I
R
NI
BN
F
O
S
(1)
30
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
Dividing this expression by the noise gain
(NG (1 RF/RG)) will give the equivalent
input-referred spot noise voltage at the noninverting
input, as shown in Equation 2:
THERMAL ANALYSIS
=
+
Maximum desired junction temperature will set the
maximum allowed internal power dissipation, as
described below. In no case should the maximum
junction temperature be allowed to exceed +150°C.
2
2
RF
NG
4kTRF
NG
) ǒIBI Ǔ )
2
ǒ
SǓ
) 4kTRS
+ Ǹ
EN
ENI ) IBN
R
Operating junction temperature (TJ) is given by
TA + PD × θJA. The total internal power dissipation
(PD) is the sum of quiescent power (PDQ) and
(2)
Evaluating these two equations for the circuit and
component values shown in Figure 70 will give a total
output spot noise voltage of 19.3nV/√Hz and a total
equivalent input spot noise voltage of 9.65nV/√Hz.
This is including the noise added by the resistors.
This total input-referred spot noise voltage is not
much higher than the 9.2nV/√Hz specification for the
op amp voltage noise alone.
additional power dissipated in the output stage (PDL
)
to deliver load power. Quiescent power is simply the
specified no-load supply current times the total supply
voltage across the part. PDL will depend on the
required output signal and load; though, for resistive
loads connected to mid-supply (VS/2), PDL is at a
maximum when the output is fixed at a voltage equal
2
to VS/4 or 3VS/4. Under this condition, PDL = VS /(16
DC ACCURACY AND OFFSET CONTROL
× RL), where RL includes feedback network loading.
The balanced input stage of
a
wideband
Note that it is the power in the output stage, and not
into the load, that determines internal power
dissipation.
voltage-feedback op amp allows good output DC
accuracy in a wide variety of applications. The
power-supply current trim for the OPA2830 gives
even tighter control than comparable products.
Although the high-speed input stage does require
relatively high input bias current (typically 5µA out of
each input terminal), the close matching between
them may be used to reduce the output DC error
caused by this current. This is done by matching the
DC source resistances appearing at the two inputs.
Evaluating the configuration of Figure 72 (which has
matched DC input resistances), using worst-case
+25°C input offset voltage and current specifications,
gives a worst-case output offset voltage equal to:
As a worst-case example, compute the maximum TJ
using an OPA2830 (MSOP-8 package) in the circuit
of Figure 72 operating at the maximum specified
ambient temperature of +85°C and driving a 150Ω
load at +2.5VDC on both outputs.
52
PD + 10V 11.9mA ) 2
+ 142mW
ƫ
ǓǓ
ƪ
ǒ
ǒ
16 150W ø 1500W
o
o
o
ǒ
Ǔ
Maximum TJ + ) 85 C ) 0.142W 150 CńW + 106 C
•
•
•
•
(NG = noninverting signal gain at DC)
Although this is still well below the specified
maximum junction temperature, system reliability
considerations may require lower ensured junction
temperatures. The highest possible internal
dissipation will occur if the load requires current to be
forced into the output at high output voltages or
sourced from the output at low output voltages. This
puts a high current through a large internal voltage
drop in the output transistors.
±(NG × VOS(MAX)) + (RF × IOS(MAX)
= ±(2 × 7.5mV)
נ
(375Ω × 1.1µA) = ±15.41mV
)
A fine-scale output offset null, or DC operating point
adjustment, is often required. Numerous techniques
are available for introducing DC offset control into an
op amp circuit. Most of these techniques are based
on adding a DC current through the feedback
resistor. In selecting an offset trim method, one key
consideration is the impact on the desired signal path
frequency response. If the signal path is intended to
be noninverting, the offset control is best applied as
an inverting summing signal to avoid interaction with
the signal source. If the signal path is intended to be
inverting, applying the offset control to the
noninverting input may be considered. Bring the DC
offsetting current into the inverting input node through
resistor values that are much larger than the signal
path resistors. This will insure that the adjustment
circuit has minimal effect on the loop gain and hence
the frequency response.
BOARD LAYOUT GUIDELINES
Achieving
optimum
performance
with
a
high-frequency amplifier like the OPA2830 requires
careful attention to board layout parasitics and
external component types. Recommendations that
will optimize performance include:
a) Minimize parasitic capacitance to any AC ground
for all of the signal I/O pins. Parasitic capacitance on
the output and inverting input pins can cause
instability: on the noninverting input, it can react with
the source impedance to cause unintentional
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
bandlimiting. To reduce unwanted capacitance, a
window around the signal I/O pins should be opened
in all of the ground and power planes around those
pins. Otherwise, ground and power planes should be
unbroken elsewhere on the board.
d) Connections to other wideband devices on the
board may be made with short direct traces or
through onboard transmission lines. For short
connections, consider the trace and the input to the
next device as a lumped capacitive load. Relatively
wide traces (50mils to 100mils) should be used,
preferably with ground and power planes opened up
around them. Estimate the total capacitive load and
set RS from the typical characteristic curve
Recommended RS vs Capacitive Load. Low parasitic
capacitive loads (< 5pF) may not need an RS since
the OPA2830 is nominally compensated to operate
with a 2pF parasitic load. Higher parasitic capacitive
loads without an RS are allowed as the signal gain
increases (increasing the unloaded phase margin). If
a long trace is required, and the 6dB signal loss
intrinsic to a doubly-terminated transmission line is
b) Minimize the distance ( < 0.25") from the
power-supply
pins
to
high-frequency
0.1µF
decoupling capacitors. At the device pins, the ground
and power-plane layout should not be in close
proximity to the signal I/O pins. Avoid narrow power
and ground traces to minimize inductance between
the pins and the decoupling capacitors. Each
power-supply
connection
should
always
be
decoupled with one of these capacitors. An optional
supply decoupling capacitor (0.1µF) across the two
power supplies (for bipolar operation) will improve
2nd-harmonic distortion performance. Larger (2.2µF
to 6.8µF) decoupling capacitors, effective at lower
frequency, should also be used on the main supply
pins. These may be placed somewhat farther from
the device and may be shared among several
devices in the same area of the PC board.
acceptable, implement
a
matched impedance
transmission line using microstrip or stripline
techniques (consult an ECL design handbook for
microstrip and stripline layout techniques). A 50Ω
environment is normally not necessary onboard, and
in fact, a higher impedance environment will improve
distortion as shown in the distortion versus load plots.
With a characteristic board trace impedance defined
(based on board material and trace dimensions), a
matching series resistor into the trace from the output
of the OPA2830 is used as well as a terminating
shunt resistor at the input of the destination device.
Remember also that the terminating impedance will
be the parallel combination of the shunt resistor and
the input impedance of the destination device; this
total effective impedance should be set to match the
c) Careful selection and placement of external
components will preserve the high-frequency
performance. Resistors should be
a very low
reactance type. Surface-mount resistors work best
and allow a tighter overall layout. Metal film or carbon
composition axially-leaded resistors can also provide
good high-frequency performance. Again, keep their
leads and PC board traces as short as possible.
Never use wire-wound type resistors in
a
high-frequency application. Since the output pin and
inverting input pin are the most sensitive to parasitic
capacitance, always position the feedback and series
output resistor, if any, as close as possible to the
output pin. Other network components, such as
noninverting input termination resistors, should also
be placed close to the package. Where double-side
component mounting is allowed, place the feedback
resistor directly under the package on the other side
of the board between the output and inverting input
pins. Even with a low parasitic capacitance shunting
the external resistors, excessively high resistor values
can create significant time constants that can
degrade performance. Good axial metal film or
surface-mount resistors have approximately 0.2pF in
shunt with the resistor. For resistor values > 1.5kΩ,
this parasitic capacitance can add a pole and/or zero
below 500MHz that can effect circuit operation. Keep
resistor values as low as possible consistent with
load driving considerations. The 750Ω feedback used
in the Typical Characteristics is a good starting point
for design.
trace impedance. If the 6dB attenuation of
a
doubly-terminated transmission line is unacceptable,
a long trace can be series-terminated at the source
end only. Treat the trace as a capacitive load in this
case and set the series resistor value as shown in the
typical characteristic curve Recommended RS vs
Capacitive Load. This will not preserve signal integrity
as well as a doubly-terminated line. If the input
impedance of the destination device is low, there will
be some signal attenuation due to the voltage divider
formed by the series output into the terminating
impedance.
e) Socketing
a
high-speed part is not
recommended. The additional lead length and
pin-to-pin capacitance introduced by the socket can
create an extremely troublesome parasitic network
which can make it almost impossible to achieve a
smooth, stable frequency response. Best results are
obtained by soldering the OPA2830 onto the board.
32
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
OPA2830
www.ti.com.................................................................................................................................................. SBOS309D–AUGUST 2004–REVISED AUGUST 2008
INPUT AND ESD PROTECTION
These diodes provide moderate protection to input
overdrive voltages above the supplies as well. The
protection diodes can typically support 30mA
continuous current. Where higher currents are
possible (that is, in systems with ±15V supply parts
driving into the OPA2830), current-limiting series
resistors should be added into the two inputs. Keep
these resistor values as low as possible, since high
values degrade both noise performance and
frequency response.
The OPA2830 is built using a very high-speed
complementary bipolar process. The internal junction
breakdown voltages are relatively low for these very
small geometry devices. These breakdowns are
reflected in the Absolute Maximum Ratings table. All
device pins are protected with internal ESD protection
diodes to the power supplies, as shown in Figure 86.
+VCC
External
Pin
Internal
Circuitry
−
VCC
Figure 86. Internal ESD Protection
Copyright © 2004–2008, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Link(s): OPA2830
OPA2830
SBOS309D–AUGUST 2004–REVISED AUGUST 2008.................................................................................................................................................. www.ti.com
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (March 2006) to Revision D .................................................................................................. Page
•
Changed rating of storage temperature range in Absolute Maximum Ratings table from –40°C to +125°C to –65°C
to +125°C............................................................................................................................................................................... 2
Changes from Revision B (February 2006) to Revision C ............................................................................................. Page
•
Changed Differential Input Voltage to ±2.5V from ±1.2V....................................................................................................... 2
34
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA2830
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
OPA2830ID
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
SOIC
SOIC
D
8
8
8
8
8
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
OPA
2830
OPA2830IDG4
OPA2830IDGKR
OPA2830IDGKT
OPA2830IDR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
DGK
DGK
D
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
OPA
2830
VSSOP
VSSOP
SOIC
2500
250
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
A59
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
A59
2500
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
OPA
2830
OPA2830IDRG4
SOIC
D
Green (RoHS
& no Sb/Br)
CU NIPDAU
OPA
2830
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
OPA2830IDGKR
OPA2830IDGKT
OPA2830IDR
VSSOP
VSSOP
SOIC
DGK
DGK
D
8
8
8
2500
250
330.0
180.0
330.0
12.4
12.4
12.4
5.3
5.3
6.4
3.4
3.4
5.2
1.4
1.4
2.1
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA2830IDGKR
OPA2830IDGKT
OPA2830IDR
VSSOP
VSSOP
SOIC
DGK
DGK
D
8
8
8
2500
250
367.0
210.0
367.0
367.0
185.0
367.0
35.0
35.0
35.0
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明