OPA358AIDCKT [TI]

3V Single-Supply 80MHz High-Speed Op Amp;


型号：	OPA358AIDCKT
厂家：	TEXAS INSTRUMENTS
描述：	3V Single-Supply 80MHz High-Speed Op Amp 放大器光电二极管
文件：	总18页 (文件大小：857K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

OPA358

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

3V Single-Supply

80MHz High-Speed Op Amp in SC70

F_DEATURES

DESCRIPTION

HIGH BANDWIDTH: 80MHz

The high-speed OPA358 amplifier is optimized for 3V

single-supply operation. The output typically swings within

5mV of GND with a 150Ω load connected to GND. The

input common-mode range includes GND and swings to

within 1V of the positive power supply. The OPA358 offers

excellent video performance: 0.5dB gain flatness is

25MHz, differential gain is 0.3%, and differential phase is

0.7°.

HIGH SLEW RATE: 55V/µs

EXCELLENT VIDEO PERFORMANCE

− 0.5dB GAIN FLATNESS: 25MHz

− DIFFERENTIAL GAIN: 0.3%

− DIFFERENTIAL PHASE: 0.7°

INPUT RANGE INCLUDES GROUND

RAIL-TO-RAIL OUTPUT

The OPA358 is optimized for supply voltages from +2.7V

to +3.3V, with an operating range of +2.5V to +3.6V.

Quiescent current is only 5.2mA per channel.

SHUTDOWN CURRENT: < 5µA

LOW QUIESCENT CURRENT: 5.2mA

SINGLE-SUPPLY OPERATING RANGE:

+2.7V to +3.3V

In shutdown mode, the quiescent current is reduced to

< 5µA, dramatically reducing power consumption. This is

especially important in battery-operated equipment such

as digital still cameras (DSCs) or mobile phones with

integrated cameras.

MicroSIZE PACKAGE: SC70-6

A_DPPLICATIONS

The OPA358 is available in SC70-6, the smallest package

currently available for video applications.

DIGITAL STILL CAMERAS

CAMERA PHONES

DIGITAL MEDIA PLAYERS

DIGITAL VIDEO CAMERAS

SET-TOP-BOX VIDEO FILTERS

OPTICAL POWER MONITORING

TRANSIMPEDANCE AMPLIFIERS

AUTOMATIC TEST EQUIPMENT

OPA358 RELATED PRODUCTS

FEATURES

PRODUCT

OPA360

OPA357

OPA355

OPA350

OPA692

THS412x

G = 2, Internal Filter, Sag Correction, Shutdown, Video Amp

100MHz GBW, RR I/O, Shutdown, CMOS Amp

200MHz GBW, RR Out, Shutdown, CMOS Amp

38MHz GBW, RR I/O, CMOS Amp

> 200MHz, Shutdown, Video Buffer Amp, G = 2

100MHz BW, Differential Input/Output, 3.3V Supply

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments

semiconductor products and disclaimers thereto appears at the end of this data sheet.

All trademarks are the property of their respective owners.

ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ

ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ

ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ

www.ti.com

ꢂꢀꢉꢠ ꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

(1)

PACKAGE/ORDERING INFORMATION

SPECIFIED

TEMPERATURE

RANGE

PACKAGE

DESIGNATOR

PACKAGE

MARKING

ORDERING

NUMBER

TRANSPORT

MEDIA, QUANTITY

PRODUCT

PACKAGE

OPA358AIDCKT

OPA358AIDCKR

Tape and Reel, 250

Tape and Reel, 3000

OPA358

SC70-6

DCK

−40°C to +85°C

AUS

(1)

For the most current package and ordering information, see the Package Option Addendum located at the end of this document, or see the

TI website at www.ti.com.

This integrated circuit can be damaged by ESD. Texas

Instruments recommends that all integrated circuits be

handledwith appropriate precautions. Failure to observe

(1)

ABSOLUTE MAXIMUM RATINGS

Supply Voltage, V+ to V− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V

(2)

proper handling and installation procedures can cause damage.

Signal Input Terminals, Voltage

Signal Input Terminals, Current

. . . . (V−) −0.5V to (V+) + 0.5V

. . . . . . . . . . . . . . . . . . . . 10mA

(2)

ESD damage can range from subtle performance degradation to

complete device failure. Precision integrated circuits may be more

susceptible to damage because very small parametric changes could

cause the device not to meet its published specifications.

(3)

Output Short-Circuit

. . . . . . . . . . . . . . . . . . . . . . . . . Continuous

Operating Temperature . . . . . . . . . . . . . . . . . . . . . . −40°C to +85°C

Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +160°C

Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . +300°C

ESD Rating:

Human Body Model (HBM) . . . . . . . . . . . . . . . . . . . . . . . 4000V

Charged Device Model (CDM) . . . . . . . . . . . . . . . . . . . . 1500V

Machine Model (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400V

(1)

Stresses above these ratings may cause permanent damage.

Exposure to absolute maximum conditions for extended periods

may degrade device reliability. These are stress ratings only, and

functional operation of the device at these or any other conditions

beyond those specified is not implied.

(2)

(3)

Input terminals are diode-clamped to the power-supply rails.

Input signals that can swing more than 0.5V beyond the supply

rails should be current-limited to 10mA or less.

Short-circuit to ground, one amplifier per package.

PIN CONFIGURATIONS

OPA358

V+

GND

Enable

Out

−

SC70−6⁽¹⁾

(1) Pin 1 is determined by orienting the package marking as indicated in the diagram.

ꢂ

ꢀ

ꢉ

ꢠ

ꢡ

ꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

ELECTRICAL CHARACTERISTICS: V = +2.7V to +3.3V Single-Supply

Boldface limits apply over the specified temperature range, T = −40°C to +85°C.

All specifications at T = +25°C, R = 150Ω connected to V /2, unless otherwise noted.

OPA358

TYP

PARAMETER

OFFSET VOLTAGE

Input Offset Voltage

Over Temperature

Drift

CONDITIONS

= +3.3V

Specified Temperature Range

MIN

MAX

UNITS

µV/°C

µV/V

dV /dT

vs. Power Supply

PSRR

= +2.7V to +3.3V

350

INPUT BIAS CURRENT

Input Bias Current

Input Offset Current

0.3

NOISE

Input Voltage Noise Density

f = 1MHz

6.4

nV/√Hz

INPUT VOLTAGE RANGE

Common-Mode Voltage Range

Common-Mode Rejection Ratio

(V−) − 0.1

(V+) − 1.0

CMRR

= +3.3V, −0.1V < V

Specified Temperature Range

< 2.3V

INPUT IMPEDANCE

Differential

Common-Mode

10 || 1.5

Ω || pF

10 || 1.5

OPEN-LOOP GAIN

Open-Loop Voltage Gain

Over Temperature

= +3.3V, 0.1V < V < 3.1V

See Typical Characteristics

FREQUENCY RESPONSE

Gain-Bandwidth Product

Bandwidth for 0.1dB Gain Flatness

Bandwidth for 0.5dB Gain Flatness

Slew Rate

Settling Time to 0.1%

Differential Gain Error

Differential Phase Error

GBW

0.1dB

0.5dB

G = +10, R = 1kΩ

0.3

0.7

MHz

V/µs

G = +2, V = 100mV , R = 560Ω

= +3.3V, G = +2, 2.5V Output Step

G = 1, R = 150Ω

PAL, R = 150Ω

OUTPUT

Voltage Output Swing from Rail

Over Temperature

= +3.3V, A

> 84dB

= +3.3V

(V−) + 100

(V+) − 200

(V+) − 300

Ω

= +3.3V, V = 0V, R = 150Ω to GND

(1)

Output Current

Open-Loop Output Impedance

= +3.3V, 0.5V from Supplies

f = 1MHz, I = 0

POWER SUPPLY

Specified Voltage Range

Minimum Operating Voltage Range

Quiescent Current

2.7

3.3

2.5 to 3.6

5.2

= +3.3V, Enabled, I = 0

7.5

8.5

Specified Temperature Range

ENABLE/SHUTDOWN FUNCTION

Disabled (logic−LOW Threshold)

Enabled (logic−HIGH Threshold)

Enable Time

Disable Time

Shutdown Current

0.8

µs

µA

1.6

1.5

2.5

= +3.3, Disabled

TEMPERATURE RANGE

Specified Range

Operating Range

Storage Range

−40

−65

+85

+150

°C

Thermal Resistance

SC70

250

°C/W

(1)

See typical characteristics chart, Output Voltage Swing vs Output Current.

ꢂ

ꢀ

ꢉ

ꢠ

ꢡ

ꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

TYPICAL CHARACTERISTICS

All specifications at T = +25°C, R = 150Ω connected to V /2, unless otherwise noted.

POWER−SUPPLY AND COMMON−MODE

REJECTION RATIO vs FREQUENCY

OPEN−LOOP GAIN AND PHASE vs FREQUENCY

200

180

160

140

120

100

200

180

160

140

120

100

+PSRR

Phase

Gain

CMRR

−

PSRR

−20

100

10k

100k

10M 100M

10k

100k

10M

100M

Frequency (MHz)

Frequency (Hz)

INPUT VOLTAGE NOISE SPECTRAL DENSITY

GAIN FLATNESS vs FREQUENCY

1.0

0.5

1000

100

G = 2

−

0.5

1.0

100

10k

100k

10M

Frequency (MHz)

Frequency (Hz)

OFFSET VOLTAGE PRODUCTION DISTRIBUTION

DIFFERENTIAL GAIN

INP = C

SYNC = INT

MTIME = 1

LINE = 330

−

DG1

0 . 1 9 %1

0 . 2 8 % .

0 . 3 0 % .

0 . 2 8 %5

DG2

DG3

DG4

DG5

STEPS

ZOOM

SAVE

RESULTS

DIFFERENTIAL PHASE

INP = C

SYNC = INT

MTIME = 1

LINE = 330

−

DP1

DP2

DP3

DP4

DP5

0 . 1 3 d g 1

0 . 1 6 d g .

0 . 4 7 d g .

0 . 6 6 d g .

0 . 6 9 d g 5

STEPS

ZOOM

SAVE

RESULTS

Offset Voltage (mV)

ꢂ ꢀꢉ ꢠꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

TYPICAL CHARACTERISTICS (continued)

All specifications at T = +25°C, R = 150Ω connected to V /2, unless otherwise noted.

QUIESCENT CURRENT vs TEMPERATURE

SHUTDOWN CURRENT vs TEMPERATURE

3.5

3.0

2.5

2.0

1.5

1.0

0.5

−

100

−

100

125

Temperature ( C)

OPEN−LOOP GAIN, COMMON−MODE REJECTION, AND

POWER−SUPPLY REJECTION RATIO vs TEMPERATURE

INPUT BIAS CURRENT vs TEMPERATURE

110

100

A_OL

PSRR

CMRR

0.1

0.01

0.001

−

100

−

100

Temperature ( C)

OUTPUT VOLTAGE vs OUTPUT CURRENT

LARGE−SIGNAL TRANSIENT

(V+)

−55_C

G = 2

−

(V+) 0.5

85 C

−

(V+) 1.0

25 C

−

(V+) 1.5

(V−) + 1.5

−55_C

−

(V ) + 1.0

25 C

85_C

−

(V ) + 0.5

(V−)

100

Time (25ns/div)

Output Current (mA)

ꢂꢀꢉꢠ ꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

TYPICAL CHARACTERISTICS (continued)

All specifications at T = +25°C, R = 150Ω connected to V /2, unless otherwise noted.

ENABLE FUNCTION

SMALL−SIGNAL TRANSIENT

G = 1

Enabled

V_OUT

Disabled

Time (500ns/div)

Time (25ns/div)

ꢂ ꢀꢉ ꢠꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

closer to the supply rails while maintaining high open-loop

gain. If the load is connected to ground, the OPA358 output

typically swings to within 5mV of ground. See the typical

characteristic curve, Output Voltage Swing vs Output

Current.

APPLICATIONS INFORMATION

OPERATING VOLTAGE

The OPA358 is fully specified from +2.7V to +3.3V over a

temperature range of −40°C to +85°C. Parameters that

vary significantly with operating voltages or temperature

are shown in the Typical Characteristics.

ENABLE/SHUTDOWN

Power-supply pins should be bypassed with a 100nF

ceramic capacitor.

The OPA358 has a shutdown feature that disables the

output and reduces the quiescent current to less than 5µA.

This feature is especially useful for portable video

applications such as digital still cameras (DSCs) and

camera phones, where the equipment is infrequently

connected to a TV or other video device.

INPUT VOLTAGE

The input common-mode range of the OPA358 extends

from (V−) − 0.1V to (V+) − 1.0V.

The Enable logic input voltage is referenced to the

OPA358 GND pin. A logic level HIGH applied to the enable

pin enables the op amp. A valid logic HIGH is defined as

≥ 1.6V above GND. A valid logic LOW is defined as ≤ 0.8V

above GND. If the Enable pin is not connected, internal

pull-up circuitry will enable the amplifier. Enable pin

voltage levels are tested for a valid logic HIGH threshold

of 1.6V minimum and a valid logic LOW threshold of 0.8V

maximum.

INPUT OVER-VOLTAGE PROTECTION

All OPA358 pins are static-protected with internal ESD

protection diodes connected to the supplies. These diodes

will provide input overdrive protection if the current is

externally limited to 10mA.

RAIL-TO-RAIL OUTPUT

A class AB output stage with common-source transistors

is used to achieve rail-to-rail output. For a 150Ω load, the

output voltage swing is 100mV from the negative rail and

200mV from the positive rail when the load is connected

to V_S/2. For lighter loads, the output swings significantly

The enable time is 1.5µs and the disable time is only 50ns.

This allows the output of the OPA358 to be multiplexed

onto a common output bus. When disabled, the output

assumes a high-impedance state.

+3V

100nF

V_OUT

Television

V_IN

Ω

Figure 1. Typical Circuit Using the OPA358 in a Gain = 2 Configuration

ꢂꢀꢉꢠ ꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

amplitudes. Figure 3 shows the multiburst test pattern;

Figure 4 shows the multipulse. The top waveforms in

these figures show the full test pattern. The middle and

bottom waveform are a more detailed view of the critical

portion of the full waveform. The middle waveform

represents the input signal from the video generator; the

bottom waveform is the OPA358 output to the line.

VIDEO PERFORMANCE

Industry standard video test patterns include:

Multiburst—packets of different test frequencies to

check for basic frequency response.

Multipulse—pulses

modulated

different

frequencies to test for comprehensive measurement

of amplitude and group delay errors across the video

baseband.

Chrominance-to-luminence (CCIR17) — tests ampli-

tude, phase and some distortion

Figure 2 shows the test circuits for Figure 3 through

Figure 13 and Figure 16. (NOTE: 1 and 2 indicate

measurement points corresponding to the waveforms

labeled 1 and 2 in the figures.)

Ω

500

Ω

500

a. Test circuit for Figure 3 through Figure 5.

Figure 3. Multiburst (CCIR 18) Test Pattern (PAL)

Ω

500

Ω

500

b. Test circuit for Figure 6.

NOTE: 1 and 2 indicate measurement points

corresponding to the waveforms labeled 1 and

2 in the figures.

Figure 2. Test Circuits Used for Figure 3 through

Figure 6

FREQUENCY RESPONSE OF THE OPA358

Frequency response measurements evaluate the ability of

a video system to uniformly transfer signal components of

different frequencies without affecting their respective

Figure 4. Multipulse Test Pattern (PAL)

ꢂ ꢀꢉ ꢠꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

Chrominance-to-luminence gain inequality (or relative

chrominance level) is a change in the gain ratio of the

chrominance and luminence components of a video

signal, which are at different frequencies. A common test

pattern is the pulse in test pattern CCIR 17, shown in

Figure 5. As in Figure 3 and Figure 4, the top waveform

shows the full test pattern. The middle and bottom

waveform are a more detailed view of the critical portion of

the full waveform, with the middle waveform representing

the input signal from the video generator and the bottom

waveform being the OPA358 output to the line.

100Hz range produces field tilt which can interfere with

proper recovery of synchronization signals in the television

receiver.

600mV

Figure 6. OPA358 Output Swing with Input Sync

Level at 0V

The OPA358 with sag correction (Figure 7b) creates an

amplitude response peak in the 20Hz region. This small

amount of peaking (a few tenths of a dB) provides

compensation of the phase response in the critical 50Hz

to 100Hz range, greatly reducing field tilt. Note that two

significantly smaller and lower-cost capacitors are

required.

Figure 5. CCIR 17 Test Pattern (PAL)

Gain errors most commonly appear as attenuation or

peaking of the chrominance information. This shows up in

the picture as incorrect color saturation. Delay distortion

will cause color smearing or bleeding, particularly at the

edges of objects in the picture. It may also cause poor

reproduction of sharp luminence transitions.

220 F

Ω

G = 2

Figure 3 through Figure 5 show that the OPA358 causes

no visible distortion or change in gain throughout the entire

video frequency range.

a) Traditional Video Circuit

OUTPUT SWING TO GND (SYNC PULSE)

Figure 6 shows the output swing capability of the OPA358

by driving the input with a sync level of 0V. The output of

the OPA358 swings very close to 0V, typically to within less

than 5mV with an 150Ω load connected to ground.

47 F

Ω

1.3k

22 F

Ω

499

Ω

825

SAG CORRECTION

Ω

DC Gain = 2.8

AC Gain = 2

Sag correction provides excellent video performance with

two small output coupling capacitors. It eliminates the

traditional, large 220µF output capacitor. The traditional

220µF circuit (Figure 7a) creates a single low frequency

pole (−3dB frequency) at 5Hz. If this capacitor is made

much smaller, excessive phase shift in the critical 50Hz to

b) OPA358 with Sag Correction

Figure 7. Traditional Video Circuit vs OPA358

with Sag Correction

ꢂꢀꢉꢠ ꢡꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

The output voltage swing for the circuit with sag correction

(see Figure 7b) is a function of the coupling capacitor

value. The value of the sag correction capacitor has only

a minor influence. The smaller the coupling capacitor, the

greater the output swing. Therefore, to accommodate the

large signal swing with very small coupling capacitors

(22µF and 33µF), a higher supply voltage might be

needed.

WIDEBAND VIDEO MULTIPLEXING

One common application for video amplifiers which

include an enable pin is to wire multiple amplifier outputs

together, then select which one of several possible video

inputs to source onto a single line. This simple Wired-OR

Video Multiplexer can be easily implemented using the

OPA358, as shown in Figure 9.

DC-COUPLED OUTPUT

V+ = 2.7V to 3.3V

Enable

Due to the excellent swing to ground, the OPA358 can also

be DC- coupled to a video load. As shown in Figure 8, this

eliminates the need for AC-coupling capacitors at the

output. This is especially important in portable video

applications where board space is restricted.

R_OUT

Video

DAC

Ω

(1)

OPA358

Ω

The DC-coupled output configuration also shows the best

video performance. There is no line or field tilt—allowing

use of the lowest power supply. In this mode, the OPA358

will safely operate down to 2.5V with no clipping of the

signal.

R₁

R₂

G = 1 +

Television

or VCR

R₂

GND

The disadvantage with DC-coupled output is that it uses

somewhat higher supply current.

Ω

NOTE: (1) Optional 200 for use with TI’s digital media processors,

Ω

and 500 for OMAP2420 and OMAP2430 processors.

Figure 8. DC-Coupled Input/DC-Coupled Output

+3.3

1 F

10nF

Ω

Signal #1

OPA358

Ω

V_OUT

Ω

+3.3V

1 F

10nF

Ω

Signal #2

OPA358

Ω

HCO4

B_ON

Select

A_ON

Figure 9. Multiplexed Output

ꢂ

ꢀ

ꢉ

ꢠ

ꢡ

ꢢ

www.ti.com

SB0S296C − MARCH 2004 − REVISED FEBRUARY 2005

The key elements to a transimpedance design, as shown

in Figure 11, are the expected diode capacitance

(including the parasitic input common-mode and

differential-mode input capacitance (1.5 + 1.5)pF for the

OPA358), the desired transimpedance gain (R_F), and the

Gain Bandwidth Product (GBW) for the OPA358 (80MHz).

With these 3 variables set, the feedback capacitor value

(C_F) may be set to control the frequency response.

CAPACITIVE LOAD AND STABILITY

The OPA358 can drive a wide range of capacitive loads.

However, all op amps under certain conditions may

become unstable. Op amp configuration, gain, and load

value are just a few of the factors to consider when

determining stability. An op amp in unity-gain configuration

is most susceptible to the effects of capacitive loading. The

capacitive load reacts with the op amp output resistance,

along with any additional load resistance, to create a pole

in the small-signal response that degrades the phase

margin.

C_F

<1pF

One method of improving capacitive load drive in the

unity-gain configuration is to insert a 10Ω to 20Ω resistor

in series with the output, as shown in Figure 10. This

significantly reduces ringing with large capacitive loads.

However, if there is a resistive load in parallel with the

capacitive load, R_Screates a voltage divider. This

introduces a DC error at the output and slightly reduces

output swing. This error may be insignificant. For instance,

with R_L= 10kΩ and R_S= 20Ω, there is only about a 0.2%

error at the output.

(prevents gain peaking)

R_F

Ω

10M

C_D

V_OUT

OPA358

To enable,

connect to V+

or drive with logic.

V+

R_S

V_OUT

Figure 11. Transimpedance Amplifier

OPA358

V_IN

R_L

C_L

To achieve a maximally flat 2nd-order Butterworth

frequency response, the feedback pole should be set to:

To enable,

connect to V+

or drive with logic.

GBW

4pR_FC_D

2pR_FC_F

(1)

Figure 10. Series Resistor in Unity-Gain

Typical surface-mount resistors have

capacitance of around 0.2pF that must be deducted from

the calculated feedback capacitance value.

parasitic

Configuration Improves Capacitive Load Drive

WIDEBAND TRANSIMPEDANCE AMPLIFIER

Bandwidth is calculated by:

Wide bandwidth, low input bias current, and low input

voltage and current noise make the OPA358 an ideal

wideband photodiode transimpedance amplifier for

low-voltage single-supply applications. Low-voltage noise

is important because photodiode capacitance causes the

effective noise gain of the circuit to increase at high

frequency.

GBW

2pR_FC_D

f_*3dB

(2)

For even higher transimpedance bandwidth, the CMOS

OPA380 (90MHz GBW), OPA355 (200MHz GBW), or the

OPA655 (400MHz GBW) may be used.

PACKAGE OPTION ADDENDUM

www.ti.com

10-Jun-2014

PACKAGING INFORMATION

Orderable Device

OPA358AIDCKR

OPA358AIDCKT

OPA358AIDCKTG4

Status Package Type Package Pins Package

Eco Plan

Lead/Ball Finish

MSL Peak Temp

Op Temp (°C)

-40 to 85

Device Marking

Samples

Drawing

Qty

(1)

(2)

(6)

(3)

(4/5)

ACTIVE

SC70

DCK

3000

Green (RoHS

& no Sb/Br)

CU NIPDAU

Level-1-260C-UNLIM

AUS

ACTIVE

DCK

250

Green (RoHS

& no Sb/Br)

-40 to 85

Green (RoHS

& no Sb/Br)

-40 to 85

⁽¹⁾The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

⁽²⁾Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

⁽³⁾MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

⁽⁴⁾There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

⁽⁵⁾Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

⁽⁶⁾Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

Addendum-Page 1

PACKAGE OPTION ADDENDUM

www.ti.com

10-Jun-2014

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 2

PACKAGE MATERIALS INFORMATION

www.ti.com

25-Feb-2013

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device

Package Package Pins

Type Drawing

SPQ

Reel

Pin1

Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant

(mm) W1 (mm)

OPA358AIDCKR

OPA358AIDCKT

SC70

DCK

3000

250

179.0

178.0

8.4

9.0

2.2

2.4

2.5

1.2

4.0

8.0

250

Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com

25-Feb-2013

*All dimensions are nominal

Device

Package Type Package Drawing Pins

SPQ

Length (mm) Width (mm) Height (mm)

OPA358AIDCKR

OPA358AIDCKT

SC70

DCK

3000

250

203.0

180.0

203.0

180.0

35.0

18.0

250

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products

Applications

Audio

www.ti.com/audio

amplifier.ti.com

dataconverter.ti.com

www.dlp.com

Automotive and Transportation www.ti.com/automotive

Communications and Telecom www.ti.com/communications

Amplifiers

Data Converters

DLP® Products

DSP

Computers and Peripherals

Consumer Electronics

Energy and Lighting

Industrial

www.ti.com/computers

www.ti.com/consumer-apps

www.ti.com/energy

dsp.ti.com

Clocks and Timers

Interface

www.ti.com/clocks

interface.ti.com

logic.ti.com

www.ti.com/industrial

www.ti.com/medical

Medical

Logic

Security

www.ti.com/security

Power Mgmt

Microcontrollers

RFID

power.ti.com

Space, Avionics and Defense

Video and Imaging

www.ti.com/space-avionics-defense

www.ti.com/video

microcontroller.ti.com

www.ti-rfid.com

www.ti.com/omap

OMAP Applications Processors

Wireless Connectivity

TI E2E Community

e2e.ti.com

www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

OPA358AIDCKT [TI]

相关型号：

OPA358AIDCKTG4

OPA358AIDR

OPA358IDBVT

OPA358IDCKR

OPA358IDCKT

OPA359IDBVT

OPA359IDCKR

OPA359IDCKT

OPA360

OPA360

OPA360AIDBVT

OPA360AIDCKR