OPA4350EA/250 [TI]
四路、单电源、轨到轨、高速、低噪声运算放大器 | DBQ | 16;型号: | OPA4350EA/250 |
厂家: | TEXAS INSTRUMENTS |
描述: | 四路、单电源、轨到轨、高速、低噪声运算放大器 | DBQ | 16 放大器 运算放大器 放大器电路 |
文件: | 总28页 (文件大小:1191K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
OPA350
OPA2350
OPA4350
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
High-Speed, Single-Supply, Rail-to-Rail
OPERATIONAL AMPLIFIERS
MicroAmplifiertSeries
FD EATURES
DESCRIPTION
RAIL-TO-RAIL INPUT
The OPA350 series rail-to-rail CMOS operational
D
D
D
D
D
D
D
D
RAIL-TO-RAIL OUTPUT (within 10mV)
WIDE BANDWIDTH: 38MHz
HIGH SLEW RATE: 22V/µs
LOW NOISE: 5nV/√Hz
amplifiers are optimized for low voltage, single-supply
operation. Rail-to-rail input/output, low noise (5nV/√Hz),
and high speed operation (38MHz, 22V/µs) make them
ideal for driving sampling Analog-to-Digital (A/D)
converters. They are also well suited for cell phone PA
control loops and video processing (75Ω drive capability)
as well as audio and general purpose applications. Single,
dual, and quad versions have identical specifications for
maximum design flexibility.
LOW THD+NOISE: 0.0006%
UNITY-GAIN STABLE
MicroSIZE PACKAGES
SINGLE, DUAL, AND QUAD
The OPA350 series operates on a single supply as low as
2.5V with an input common-mode voltage range that
extends 300mV below ground and 300mV above the
positive supply. Output voltage swing is to within 10mV of
the supply rails with a 10kΩ load. Dual and quad designs
feature completely independent circuitry for lowest
crosstalk and freedom from interaction.
AD PPLICATIONS
CELL PHONE PA CONTROL LOOPS
D
D
D
D
D
D
D
D
DRIVING A/D CONVERTERS
VIDEO PROCESSING
DATA ACQUISITION
PROCESS CONTROL
AUDIO PROCESSING
COMMUNICATIONS
ACTIVE FILTERS
The single (OPA350) and dual (OPA2350) come in the
miniature MSOP-8 surface mount, SO-8 surface mount,
and DIP-8 packages. The quad (OPA4350) packages are
the space-saving SSOP-16 surface mount and SO-14
surface mount. All are specified from −40°C to +85°C and
operate from −55°C to +150°C.
TEST EQUIPMENT
SPICE model available at www.ti.com
OPA4350
OPA350
NC
NC
−In
+In
1
2
3
4
8
7
6
5
OPA4350
V+
Out A
−In A
+In A
+V
1
2
3
4
5
6
7
8
16 Out D
15 −In D
14 +In D
Out A
−In A
+In A
V+
1
2
3
4
5
6
7
14 Out D
13 −In D
12 +In D
11 V−
Output
NC
A
B
D
C
−
V
A
B
D
C
−
13
V
DIP−8, SO−8, MSOP−8
OPA2350
+In B
−In B
Out B
NC
12 +In C
11 −In C
10 Out C
+In B
−In B
Out B
10 +In C
Out A
−In A
+In A
−
1
2
3
4
8
V+
9
8
−In C
A
7
Out B
−In B
+In B
Out C
B
6
9
NC
5
SO−14
SSOP−16
DIP−8, SO−8, MSOP−8
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ
ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ
ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ
Copyright 2000−2005, Texas Instruments Incorporated
www.ti.com
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
(1)
ELECTROSTATIC DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handledwith appropriate precautions. Failure to observe
(2)
Signal Input Terminals , Voltage . . . . . (V−) − 0.3V to (V+) + 0.3V
Current . . . . . . . . . . . . . . . . . . . . . . 10mA
(3)
Open Short-Circuit Current
. . . . . . . . . . . . . . . . . . . . Continuous
proper handling and installation procedures can cause damage.
Operating Temperature Range . . . . . . . . . . . . . . . −55°C to +150°C
Storage Temperature Range . . . . . . . . . . . . . . . . . −55°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
(1)
Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(2)
(3)
Input terminals are diode-clamped to the power-supply rails.
Input signals that can swing more than 0.3V beyond the supply
rails should be current limited to 10mA or less.
Short-circuit to ground, one amplifier per package.
(1)
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESIGNATOR
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
SINGLE
PACKAGE-LEAD
OPA350EA/250
OPA350EA/2K5
OPA350UA
Tape and Reel, 250
Tape and Reel, 2500
Rails
OPA350EA
MSOP-8
DGK
−40°C to +85°C
C50
OPA350UA
OPA350PA
SO-8
DIP-8
D
P
−40°C to +85°C
−40°C to +85°C
OPA350UA
OPA350PA
OPA350UA/2K5
OPA350PA
Tape and Reel, 2500
Rails
DUAL
OPA2350EA/250
Tape and Reel, 250
OPA2350EA
MSOP-8
DGK
−40°C to +85°C
D50
OPA2350EA/2K5 Tape and Reel, 2500
OPA2350UA Rails
OPA2350UA/2K5 Tape and Reel, 2500
OPA2350UA
OPA2350PA
SO-8
DIP-8
D
P
−40°C to +85°C
−40°C to +85°C
OPA2350UA
OPA2350PA
OPA2350PA
Rails
QUAD
OPA4350EA/250
Tape and Reel, 250
OPA4350EA
OPA4350UA
SSOP-16
SO-14
DBQ
D
−40°C to +85°C
−40°C to +85°C
OPA4350EA
OPA4350UA
OPA4350EA/2K5 Tape and Reel, 2500
OPA4350UA Rails
OPA4350UA/2K5 Tape and Reel, 2500
(1)
For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet.
2
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
ꢂ ꢀꢉ ꢤꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
ELECTRICAL CHARACTERISTICS: V = 2.7V to 5.5V
S
Boldface limits apply over the temperature range, T = −40°C to +85°C. V = 5V.
A
S
All specifications at T = +25°C, R = 1kΩ connected to V /2 and V
= V /2, unless otherwise noted.
A
L
S
OUT
S
OPA350, OPA2350, OPA4350
(1)
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
OFFSET VOLTAGE
Input Offset Voltage
= −40°C to +85°C
V
OS
V
S
= 5V
150
500
µV
mV
T
A
1
vs Temperature
vs Power-Supply Rejection Ratio
= −40°C to +85°C
T
= −40°C to +85°C
4
µV/°C
µV/V
µV/V
µV/V
A
PSRR
V
= 2.7V to 5.5V, V
= 2.7V to 5.5V, V
dc
= 0V
40
150
S
CM
T
A
V
S
= 0V
175
CM
Channel Separation (dual, quad)
INPUT BIAS CURRENT
0.15
0.5
Input Bias Current
I
B
10
pA
pA
vs Temperature
See Typical Characteristics
Input Offset Current
I
0.5
10
OS
NOISE
Input Voltage Noise, f = 100Hz to 400kHz
Input Voltage Noise Density, f = 10kHz
Input Current Noise Density, f = 100kHz
Current Noise Density, f = 10kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-ModeRejection Ratio
4
7
5
4
µVrms
nV/√Hz
nV/√Hz
fA/√Hz
e
i
n
n
V
T
= −40°C to +85°C
−0.1
66
(V+) + 0.1
V
CM
CMRR
A
V
= 2.7V, −0.1V < V
= 5.5V, −0.1V < V
= 5.5V, −0.1V < V
< 2.8V
< 5.6V
< 5.6V
84
90
dB
dB
dB
S
S
CM
CM
CM
V
74
T
= −40°C to +85°C
V
74
A
S
INPUT IMPEDANCE
Differential
13
10 || 2.5
Ω || pF
Ω || pF
13
10 || 6.5
Common-Mode
OPEN-LOOP GAIN
Open-Loop Voltage Gain
A
OL
R
= 10kΩ, 50mV < V < (V+) −50mV
100
100
100
100
122
120
dB
dB
dB
dB
L
O
T
A
= −40°C to +85°C
R
L
= 10kW, 50mV < V < (V+) −50mV
O
R
L
= 1kΩ, 200mV < V < (V+) −200mV
O
T
A
= −40°C to +85°C
R
L
= 1kW, 200mV < V < (V+) −200mV
O
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
C
= 100pF
L
GBW
SR
G = 1
38
22
MHz
V/µs
µs
G = 1
Settling Time: 0.1%
G = 1, 2V Step
G = 1, 2V Step
0.22
0.5
0.01%
µs
Overload Recovery Time
Total Harmonic Distortion + Noise
Differential Gain Error
Differential Phase Error
V
• G = V
0.1
µs
IN
S
(2)
THD+N R = 600Ω, V = 2.5V
, G = 1, f = 1kHz
0.0006
0.17
0.17
%
L
O
PP
(3)
(3)
G = 2, R = 600Ω, V = 1.4V
%
L
O
G = 2, R = 600Ω, V = 1.4V
deg
L
O
(1)
(2)
(3)
(4)
(5)
V
V
= +5V.
S
= 0.25V to 2.75V.
OUT
NTSC signal generator used. See Figure 6 for test circuit.
Output voltage swings are measured between the output and power supply rails.
See typical characteristic curve, Output Voltage Swing vs Output Current.
3
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
ELECTRICAL CHARACTERISTICS: V = 2.7V to 5.5V (continued)
S
Boldface limits apply over the temperature range, T = −40°C to +85°C. V = 5V.
A
S
All specifications at T = +25°C, R = 1kΩ connected to V /2 and V
= V /2, unless otherwise noted.
A
L
S
OUT
S
OPA350, OPA2350, OPA4350
(1)
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
OUTPUT
Voltage Output Swing from Rail
(4)
V
R
= 10kΩ, A
= 10kW, A
≥ 100dB
ꢀ 100dB
10
25
50
50
mV
mV
mV
mV
mA
mA
OUT
OUT
L
OL
T
A
= −40°C to +85°C
R
L
OL
R
= 1kΩ, A
= 1kW, A
≥ 100dB
ꢀ 100dB
200
200
L
OL
T
A
= −40°C to +85°C
R
L
OL
(5)
40
Output Current
I
Short-Circuit Current
I
80
See Typical Characteristics
SC
C
LOAD
Capacitive Load Drive
POWER SUPPLY
Operating Voltage Range
Minimum Operating Voltage
Quiescent Current (per amplifier)
V
T
A
= −40°C to +85°C
2.7
5.5
V
S
2.5
5.2
V
I
Q
I
O
I
O
= 0
= 0
7.5
mA
mA
T
= −40°C to +85°C
8.5
A
TEMPERATURE RANGE
Specified Range
−40
−55
−55
+85
+150
+150
°C
°C
°C
Operating Range
Storage Range
Thermal Resistance
MSOP-8 Surface Mount
SO-8 Surface Mount
DIP-8
q
JA
150
150
100
100
100
°C/W
°C/W
°C/W
°C/W
°C/W
SO-14 Surface Mount
SSOP-16 Surface Mount
(1)
(2)
(3)
(4)
(5)
V
V
= +5V.
S
= 0.25V to 2.75V.
OUT
NTSC signal generator used. See Figure 6 for test circuit.
Output voltage swings are measured between the output and power supply rails.
See typical characteristic curve, Output Voltage Swing vs Output Current.
4
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
ꢂ ꢀꢉ ꢤꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
POWER SUPPLY AND COMMON−MODE
REJECTION RATIO vs FREQUENCY
OPEN-LOOP GAIN/PHASE vs FREQUENCY
100
90
80
70
60
50
40
30
20
10
0
160
140
120
100
80
0
−
−
−
−
PSRR
45
CMRR
(VS = +5V
−
= 0.1V to 5.1V)
φ
90
VCM
60
G
40
135
20
0
180
0.1
1
10
100
1k
10k 100k 1M 10M 100M
Frequency (Hz)
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
140
130
120
110
100
90
10k
1k
100k
10k
1k
Current Noise
100
10
Voltage Noise
100
10
80
1
70
Dual and quad devices.
60
0.1
1
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
HARMONIC DISTORTION + NOISE vs FREQUENCY
1
1
G = 1
VO = 2.5VPP
RL = 600Ω
(−40dBc)
RL = 600Ω
0.1
(−60dBc)
G = 100, 3VPP (VO = 1V to 4V)
G = 10, 3VPP (VO = 1V to 4V)
0.1
0.01
0.01
( 80dBc)
−
G = 1, 3VPP (VO = 1V to 4V)
Input goes through transition region
0.001
(−100dBc)
0.001
0.0001
3rd−Harmonic
2nd−Harmonic
G = 1, 2.5VPP (VO = 0.25V to 2.75V)
Input does NOT go through transition region
0.0001
(−120dBc)
1k
10k
100k
Frequency (Hz)
1M
10
100
1k
10k
100k
Frequency (Hz)
5
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
TYPICAL CHARACTERISTICS (continued)
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
OPEN−LOOP GAIN vs TEMPERATURE
DIFFERENTIAL GAIN/PHASE vs RESISTIVE LOAD
G = 2
130
125
120
115
110
0.5
0.4
0.3
0.2
0.1
0
VO = 1.4V
Phase
NTSC Signal Generator
See Figure 6 for test circuit.
Ω
RL = 1k
Ω
RL = 10k
Gain
Ω
RL = 600
−
−
−
25
75
50
0
25
50
75
100 125
0
100 200 300 400 500 600 700 800 900 1000
_
Temperature ( C)
Ω
Resistive Load (
)
SLEW RATE vs TEMPERATURE
COMMON−MODE AND POWER−SUPPLY REJECTION RATIO
vs TEMPERATURE
100
40
35
30
25
20
15
10
5
110
100
90
CMRR, VS = 5.5V
(VCM 0.1V to +5.6V)
=
−
90
80
70
60
Negative Slew Rate
Positive Slew Rate
CMRR, VS = 2.7V
(VCM = −0.1V to +2.8V)
PSRR
80
0
70
−
−
−
25
−75
−50 −25
0
25
50
75
100
125
75
50
0
25
50
75
100
125
_
Temperature (_C)
Temperature ( C)
QUIESCENT CURRENT vs SUPPLY VOLTAGE
Per Amplifier
QUIESCENT CURRENT AND
SHORT−CIRCUIT CURRENT vs TEMPERATURE
6.0
5.5
5.0
4.5
4.0
3.5
3.0
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
100
90
80
70
60
50
40
30
+ISC
I
−
SC
IQ
75
−
50
−
25
−
0
25
50
75
100 125
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Temperature ( C)
_
Supply Voltage (V)
6
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
ꢂ ꢀꢉ ꢤꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS (continued)
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
INPUT BIAS CURRENT
vs INPUT COMMON−MODE VOLTAGE
INPUT BIAS CURRENT vs TEMPERATURE
1k
100
10
1.5
1.0
0.5
0.0
1
0.1
−
0.5
−
−
−
25
75
50
0
25
50
75
100
125
−0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
_
Temperature ( C)
Common−Mode Voltage (V)
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
CLOSED−LOOP OUTPUT IMPEDANCE vs FREQUENCY
6
5
4
3
2
1
0
100
10
VS = 5.5V
Maximum output
voltage without
slew rate−induced
distortion.
1
G = 100
VS = 2.7V
0.1
G = 10
G = 1
0.01
0.001
0.0001
100k
1M
10M
100M
1
10
100
1k
10k 100k
1M
10M 100M
Frequency (Hz)
Frequency (Hz)
OPEN−LOOP GAIN vs OUTPUT VOLTAGE SWING
IOUT = 2.5mA
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
140
130
120
110
100
90
V+
µ
IOUT = 250 A
−
(V+) 1
_
+25 C
−
_
55 C
_
+125 C
−
(V+) 2
IOUT = 4.2mA
Depending on circuit configuration
(including closed−loop gain) performance
may be degraded in shaded region.
−
(V )+2
80
_
+25 C
−
_
_
55 C
+125 C
−
(V )+1
70
60
−
(V )
0
20
40 60 80 100 120 140 160 180 200
Output Voltage Swing from Rails (mV)
0
10
20
Output Current (mA)
30
40
7
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
TYPICAL CHARACTERISTICS (continued)
All specifications at T = +25°C, V = +5V, and R = 1kΩ connected to V /2, unless otherwise noted.
A
S
L
S
OFFSET VOLTAGE
PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
18
16
14
12
10
8
20
18
16
14
12
10
8
Typical distribution of
packaged units.
Typical production
distribution of
packaged units.
6
6
4
4
2
2
0
0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Offset Voltage Drift (µV/_C)
Offset Voltage ( V)
µ
SETTLING TIME vs CLOSED−LOOP GAIN
SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE
10
80
70
60
50
40
30
20
10
0
G = 1
0.01%
−
G =
1
1
G = 10
0.1%
0.1
10
100
1k
10k
100k
1M
−
−
−
100
1
10
Load Capacitance (pF)
Closed−Loop Gain (V/V)
SMALL−SIGNAL STEP RESPONSE
CL = 100pF
LARGE−SIGNAL STEP RESPONSE
CL = 100pF
100ns/div
200ns/div
8
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
ꢂ ꢀꢉ ꢤꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
OPERATING VOLTAGE
APPLICATIONS INFORMATION
OPA350 series op amps are fully specified from +2.7V
to +5.5V. However, supply voltage may range from
+2.5V to +5.5V. Parameters are tested over the
specified supply range—a unique feature of the
OPA350 series. In addition, many specifications apply
from −40°C to +85°C. Most behavior remains virtually
unchanged throughout the full operating voltage range.
Parameters that vary significantly with operating
voltage or temperature are shown in the typical
characteristics.
OPA350 series op amps are fabricated on a
state-of-the-art 0.6 micron CMOS process. They are
unity-gain stable and suitable for a wide range of
general-purpose applications. Rail-to-rail input/output
make them ideal for driving sampling A/D converters.
They are also well-suited for controlling the output
power in cell phones. These applications often require
high speed and low noise. In addition, the OPA350
series offers a low-cost solution for general-purpose
and consumer video applications (75Ω drive capability).
Excellent ac performance makes the OPA350 series
well-suited for audio applications. Their bandwidth,
slew rate, low noise (5nV/√Hz), low THD (0.0006%),
and small package options are ideal for these
applications. The class AB output stage is capable of
driving 600Ω loads connected to any point between V+
and ground.
RAIL-TO-RAIL INPUT
The tested input common-mode voltage range of the
OPA350 series extends 100mV beyond the supply rails.
This is achieved with a complementary input stage—an
N-channel input differential pair in parallel with a
P-channel differential pair, as shown in Figure 2. The
N-channel pair is active for input voltages close to the
positive rail, typically (V+) – 1.8V to 100mV above the
positive supply, while the P-channel pair is on for inputs
from 100mV below the negative supply to
approximately (V+) – 1.8V. There is a small transition
region, typically (V+) – 2V to (V+) – 1.6V, in which both
pairs are on. This 400mV transition region can vary
400mV with process variation. Thus, the transition
region (both input stages on) can range from (V+) –
2.4V to (V+) – 2.0V on the low end, up to (V+) – 1.6V
to (V+) – 1.2V on the high end.
Rail-to-rail input and output swing significantly
increases dynamic range, especially in low voltage
supply applications. Figure 1 shows the input and
output waveforms for the OPA350 in unity-gain
configuration. Operation is from a single +5V supply
with a 1kΩ load connected to V /2. The input is a 5V
S
PP
sinusoid. Output voltage swing is approximately
4.95V
.
PP
Power supply pins should be bypassed with 0.01µF
ceramic capacitors.
OPA350 series op amps are laser-trimmed to reduce
offset voltage difference between the N-channel and
P-channel input stages, resulting in improved
common-mode rejection and a smooth transition
between the N-channel pair and the P-channel pair.
However, within the 400mV transition region PSRR,
CMRR, offset voltage, offset drift, and THD may be
degraded compared to operation outside this region.
Ω
VS = +5, G = +1, RL = 1k
5V
VIN
A double-folded cascode adds the signal from the two
input pairs and presents a differential signal to the class
AB output stage. Normally, input bias current is
approximately 500fA. However, large inputs (greater
than 300mV beyond the supply rails) can turn on the
OPA350’s input protection diodes, causing excessive
current to flow in or out of the input pins. Momentary
voltages greater than 300mV beyond the power supply
can be tolerated if the current on the input pins is limited
to 10mA. This is easily accomplished with an input
resistor, as shown in Figure 3. Many input signals are
inherently current-limited to less than 10mA; therefore,
a limiting resistor is not required.
0
5V
VOUT
0
Figure 1. Rail-to-Rail Input and Output
9
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
V+
Reference
Current
VIN+
−
VIN
VBIAS1
Class AB
Control
VO
Circuitry
VBIAS2
−
V
(Ground)
Figure 2. Simplified Schematic
within a few tens of millivolts from the supply rails and
maintain high open-loop gain. See the typical
characteristics Output Voltage Swing vs Output Current
and Open-Loop Gain vs Output Voltage.
V+
CAPACITIVE LOAD AND STABILITY
IOVERLOAD
10mA max
OPA350 series op amps can drive a wide range of
capacitive loads. However, all op amps under certain
conditions may become unstable. Op amp
configuration, gain, and load value are just a few of the
factors to consider when determining stability. An op
amp in unity-gain configuration is the most susceptible
to the effects of capacitive load. The capacitive load
reacts with the op amp’s output impedance, along with
any additional load resistance, to create a pole in the
small-signal response that degrades the phase margin.
VOUT
OPAx350
VIN
Ω
5k
Figure 3. Input Current Protection for Voltages
Exceeding the Supply Voltage
In unity gain, OPA350 series op amps perform well with
very large capacitive loads. Increasing gain enhances
the amplifier’s ability to drive more capacitance. The
typical characteristic Small-Signal Overshoot vs
Capacitive Load shows performance with a 1kΩ
resistive load. Increasing load resistance improves
capacitive load drive capability.
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source
transistors is used to achieve rail-to-rail output. For light
resistive loads (>10kΩ), the output voltage swing is
typically ten millivolts from the supply rails. With heavier
resistive loads (600Ω to 10kΩ), the output can swing to
10
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
ꢂ ꢀꢉ ꢤꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
series provides an effective means of buffering the
A/D’s input capacitance and resulting charge injection
while providing signal gain.
FEEDBACK CAPACITOR IMPROVES
RESPONSE
For optimum settling time and stability with
high-impedance feedback networks, it may be
necessary to add a feedback capacitor across the
feedback resistor, RF, as shown in Figure 4. This
capacitor compensates for the zero created by the
feedback network impedance and the OPA350’s input
capacitance (and any parasitic layout capacitance).
The effect becomes more significant with higher
impedance networks.
Figure 5 shows the OPA350 driving an ADS7861. The
ADS7861 is a dual, 500kHz, 12-bit sampling converter
in the tiny SSOP-24 package. When used with the
miniature package options of the OPA350 series, the
combination is ideal for space-limited applications. For
further information, consult the ADS7861 data sheet
(SBAS110A).
OUTPUT IMPEDANCE
CF
The low frequency open-loop output impedance of the
OPA350’s
common-source
output
stage
is
RIN
RF
V+
approximately 1kΩ. When the op amp is connected with
feedback, this value is reduced significantly by the loop
gain of the op amp. For example, with 122dB of
open-loop gain, the output impedance is reduced in
unity-gain to less than 0.001Ω. For each decade rise in
the closed-loop gain, the loop gain is reduced by the
same amount which results in a ten-fold increase in
effective output impedance (see the typical
characteristic, Output Impedance vs Frequency).
VIN
CIN
•
•
RIN CIN = RF CF
VOUT
OPA350
CL
CIN
At higher frequencies, the output impedance will rise as
the open-loop gain of the op amp drops. However, at
these frequencies the output also becomes capacitive
due to parasitic capacitance. This prevents the output
impedance from becoming too high, which can cause
stability problems when driving capacitive loads. As
mentioned previously, the OPA350 has excellent
capacitive load drive capability for an op amp with its
bandwidth.
Where CIN is equal to the OPA350’s input
capacitance (approximately 9pF) plus any
parasitic layout capacitance.
Figure 4. Feedback Capacitor Improves Dynamic
Performance
It is suggested that a variable capacitor be used for the
feedback capacitor since input capacitance may vary
between op amps and layout capacitance is difficult to
determine. For the circuit shown in Figure 4, the value
of the variable feedback capacitor should be chosen so
that the input resistance times the input capacitance of
the OPA350 (typically 9pF) plus the estimated parasitic
layout capacitance equals the feedback capacitor times
the feedback resistor:
VIDEO LINE DRIVER
Figure 6 shows a circuit for a single supply, G = 2
composite video line driver. The synchronized outputs
of a composite video line driver extend below ground.
As shown, the input to the op amp should be ac-coupled
and shifted positively to provide adequate signal swing
to account for these negative signals in a single-supply
configuration.
RIN @ CIN + RF @ CF
where CIN is equal to the OPA350’s input capacitance
(sum of differential and common-mode) plus the layout
capacitance. The capacitor can be varied until optimum
performance is obtained.
The input is terminated with a 75Ω resistor and
ac-coupled with a 47µF capacitor to a voltage divider
that provides the dc bias point to the input. In Figure 6,
this point is approximately (V−) + 1.7V. Setting the
optimal bias point requires some understanding of the
nature of composite video signals. For best
performance, one should be careful to avoid the
distortion caused by the transition region of the
OPA350’s complementary input stage. Refer to the
discussion of rail-to-rail input.
DRIVING A/D CONVERTERS
OPA350 series op amps are optimized for driving
medium speed (up to 500kHz) sampling A/D
converters. However, they also offer excellent
performance for higher speed converters. The OPA350
11
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
CB1
+5V
Ω
2k
Ω
Ω
Ω
2k
2
3
4
1/ 4
1
OPA4350
VIN B1
µ
µ
0.1 F
0.1 F
CB0
24
+VD
13
+VA
Ω
2k
2k
2
3
23
22
21
20
19
18
17
16
15
14
CH B1+
SERIAL DATA A
SERIAL DATA B
BUSY
−
6
CH B1
7
4
1/ 4
CH B0+
OPA4350
5
5
VIN B0
−
CH B0
CLOCK
6
CA1
CH A1+
CS
Serial
Interface
7
ADS7861
−
CH A1
RD
CONVST
A0
Ω
2k
2k
8
CH A0+
9
−
CH A0
9
10
11
8
1/ 4
REFIN
M0
OPA4350
10
VIN A1
REFOUT
M1
CA0
DGND
AGND
12
1
Ω
2k
Ω
2k
12
13
14
1/ 4
OPA4350
VIN A0
11
VIN = 0V to 2.45V for 0V to 4.9V output.
Choose CB1, CB0, CA1, CA0 to filter high frequency noise.
Figure 5. OPA4350 Driving Sampling A/D Converter
12
ꢂ ꢀꢉ ꢠꢡꢢ
ꢂ ꢀꢉ ꢣꢠꢡ ꢢ
ꢂ ꢀꢉ ꢤꢠꢡ ꢢ
www.ti.com
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
RG
RF
Ω
Ω
1k
1k
+5V
C1
C4
µ
220 F
µ
0.1 F
+
µ
µ
10 F
0.1 F
2
3
7
C5
µ
1000 F
ROUT
Cable
6
VOUT
OPA350
C2
µ
47 F
RL
Video
In
4
R1
R2
Ω
75
Ω
5k
+5V (pin 7)
R3
R4
Ω
Ω
5k
5k
C3
µ
10 F
Figure 6. Single-Supply Video Line Driver
+5V
Ω
50k
(2.5V)
8
4
RG
REF1004−2.5
R1
R2
Ω
Ω
100k
25k
+5V
R3
R4
Ω
25k
Ω
100k
1/2
OPA2350
1/2
VO
OPA2350
RL
Ω
10k
Ω
200k
RG
G = 5 +
Figure 7. Two Op-Amp Instrumentation Amplifier With
Improved High Frequency Common-Mode Rejection
13
ꢂꢀꢉꢠ ꢡꢢ
ꢂꢀꢉꢣ ꢠꢡ ꢢ
ꢂꢀꢉꢤ ꢠꢡ ꢢ
SBOS099C − SEPTEMBER 2000 − REVISED JANUARY 2005
www.ti.com
R1
10.5k
C1
4.7nF
Ω
+2.5V
+2.5V
C1
1830pF
C2
270pF
R1
2.74kΩ
R2
19.6kΩ
VOUT
OPA350
VOUT
OPA350
RL
20kΩ
VIN
RL
VIN
20kΩ
R2
49.9k
C2
1nF
Ω
−2.5V
2.5V
−
Figure 8. 10kHz Low-Pass Filter
Figure 9. 10kHz High-Pass Filter
14
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
OPA2350EA/250
OPA2350EA/250G4
OPA2350EA/2K5
OPA2350EA/2K5G4
OPA2350PA
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
PDIP
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
250
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
D50
D50
D50
D50
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DGK
DGK
DGK
P
250
2500
2500
50
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
N / A for Pkg Type
OPA2350PA
OPA2350PA
OPA2350PAG4
OPA2350UA
PDIP
P
50
Green (RoHS
& no Sb/Br)
N / A for Pkg Type
SOIC
D
75
Green (RoHS
& no Sb/Br)
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
OPA
2350UA
OPA2350UA/2K5
OPA2350UA/2K5G4
OPA2350UAG4
OPA350EA/250
OPA350EA/250G4
OPA350EA/2K5
OPA350EA/2K5G4
OPA350PA
SOIC
D
2500
2500
75
Green (RoHS
& no Sb/Br)
OPA
2350UA
SOIC
D
Green (RoHS
& no Sb/Br)
OPA
2350UA
SOIC
D
Green (RoHS
& no Sb/Br)
OPA
2350UA
VSSOP
VSSOP
VSSOP
VSSOP
PDIP
DGK
DGK
DGK
DGK
P
250
250
2500
2500
50
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
C50
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
C50
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
C50
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
C50
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
N / A for Pkg Type
OPA350PA
OPA350PA
OPA350PAG4
PDIP
P
50
Green (RoHS
& no Sb/Br)
N / A for Pkg Type
OPA350UA
SOIC
D
75
Green (RoHS
& no Sb/Br)
Level-2-260C-1 YEAR
OPA
350UA
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
OPA350UA/2K5
OPA350UA/2K5G4
OPA350UAG4
ACTIVE
SOIC
SOIC
SOIC
SSOP
SSOP
SSOP
SSOP
SOIC
SOIC
SOIC
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
OPA
350UA
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
8
2500
75
Green (RoHS
& no Sb/Br)
-40 to 85
OPA
350UA
8
Green (RoHS
& no Sb/Br)
-40 to 85
OPA
350UA
OPA4350EA/250
OPA4350EA/250G4
OPA4350EA/2K5
OPA4350EA/2K5G4
OPA4350UA
DBQ
DBQ
DBQ
DBQ
D
16
16
16
16
14
14
14
14
250
250
2500
2500
50
Green (RoHS
& no Sb/Br)
OPA
4350EA
Green (RoHS
& no Sb/Br)
OPA
4350EA
Green (RoHS
& no Sb/Br)
-40 to 85
-40 to 85
OPA
4350EA
Green (RoHS
& no Sb/Br)
OPA
4350EA
Green (RoHS
& no Sb/Br)
OPA4350UA
OPA4350UA
OPA4350UA
OPA4350UA
OPA4350UA/2K5
OPA4350UA/2K5G4
OPA4350UAG4
D
2500
2500
50
Green (RoHS
& no Sb/Br)
D
Green (RoHS
& no Sb/Br)
D
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Jun-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
OPA2350EA/250
OPA2350EA/2K5
OPA350EA/250
OPA350UA/2K5
OPA4350EA/250
OPA4350EA/2K5
OPA4350UA/2K5
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
D
8
8
250
2500
250
180.0
330.0
180.0
330.0
180.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
16.4
5.3
5.3
5.3
6.4
6.4
6.4
6.5
3.4
3.4
3.4
5.2
5.2
5.2
9.0
1.4
1.4
1.4
2.1
2.1
2.1
2.1
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
16.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
8
8
2500
250
SSOP
SSOP
SOIC
DBQ
DBQ
D
16
16
14
2500
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Jun-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA2350EA/250
OPA2350EA/2K5
OPA350EA/250
OPA350UA/2K5
OPA4350EA/250
OPA4350EA/2K5
OPA4350UA/2K5
VSSOP
VSSOP
VSSOP
SOIC
DGK
DGK
DGK
D
8
8
250
2500
250
210.0
367.0
210.0
367.0
210.0
367.0
367.0
185.0
367.0
185.0
367.0
185.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
38.0
8
8
2500
250
SSOP
SSOP
SOIC
DBQ
DBQ
D
16
16
14
2500
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
OPA4350EA/250G4
High-Speed, Single-Supply, Rail-to-Rail Operational Amplifiers MicroAmplifier™ Series 16-SSOP
TI
OPA4350EA/2K5
High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifierSeries
BB
OPA4350UA-2K5
High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifierSeries
TI
OPA4350UA/2K5
High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifierSeries
BB
©2020 ICPDF网 联系我们和版权申明