PCI2250PCMG4 [TI]
32 位 33MHz PCI 至 PCI 桥接，符合 CompactPCI 热插拔规范，4 个主设备 | PCM | 160;
| 型号： | PCI2250PCMG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 32 位 33MHz PCI 至 PCI 桥接，符合 CompactPCI 热插拔规范，4 个主设备 | PCM | 160 时钟 PC 控制器 微控制器 总线控制器 微控制器和处理器 外围集成电路 |
| 文件： | 总85页 (文件大小：340K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PCI2250
PCIĆtoĆPCI Bridge
Data Manual
1999
PCIBus Solutions
Printed in U.S.A., 12/99
SCPS051
PCI2250
PCI-to-PCI Bridge
Data Manual
Literature Number: SCPS051
December 1999
Printed on Recycled Paper
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products
or to discontinue any product or service without notice, and advise customers to obtain the latest
version of relevant information to verify, before placing orders, that information being relied on
is current and complete. All products are sold subject to the terms and conditions of sale supplied
at the time of order acknowledgement, including those pertaining to warranty, patent
infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the
time of sale in accordance with TI’s standard warranty. Testing and other quality control
techniquesareutilizedtotheextentTIdeemsnecessarytosupportthiswarranty. Specifictesting
of all parameters of each device is not necessarily performed, except those mandated by
government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE
POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR
ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR
PRODUCTS ARENOTDESIGNED, AUTHORIZED, ORWARRANTED TOBESUITABLEFOR
USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS.
INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY
AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and
operating safeguards must be provided by the customer to minimize inherent or procedural
hazards.
TI assumes no liability for applications assistance or customer product design. TI does not
warrantorrepresentthatanylicense, eitherexpressorimplied, isgrantedunderanypatentright,
copyright, mask work right, or other intellectual property right of TI covering or relating to any
combination, machine, or process in which such semiconductor products or services might be
or are used. TI’s publication of information regarding any third party’s products or services does
not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
Contents
Section
Title
Page
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1
1.2
1.3
1.4
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
2
3
Terminal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Feature/Protocol Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.1
3.2
3.3
3.4
3.5
3.6
Introduction to the PCI2250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
PCI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Configuration Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Special Cycle Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
Secondary Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
Bus Arbitration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
3.6.1
3.6.2
3.6.3
Primary Bus Arbitration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
Internal Secondary Bus Arbitration . . . . . . . . . . . . . . . . . . . . 3–5
External Secondary Bus Arbitration . . . . . . . . . . . . . . . . . . . 3–6
3.7
3.8
3.9
Decode Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
Extension Windows With Programmable Decoding . . . . . . . . . . . . . . 3–6
System Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
3.9.1
3.9.2
3.9.3
3.9.4
3.9.5
3.9.6
3.9.7
Posted Write Parity Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Posted Write Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Target Abort on Posted Writes . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Master Abort on Posted Writes . . . . . . . . . . . . . . . . . . . . . . . 3–7
Master Delayed Write Timeout . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Master Delayed Read Timeout . . . . . . . . . . . . . . . . . . . . . . . 3–7
Secondary SERR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
3.10 Parity Handling and Parity Error Reporting . . . . . . . . . . . . . . . . . . . . . . 3–7
3.10.1
3.10.2
Address Parity Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Data Parity Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
3.11 Master and Target Abort Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
3.12 Discard Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
3.13 Delayed Transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
3.14 Multifunction Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
3.14.1
3.14.2
Compact PCI Hot Swap Support . . . . . . . . . . . . . . . . . . . . . . 3–9
PCI Clock Run Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
3.15 PCI Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
3.15.1 Behavior in Low Power States . . . . . . . . . . . . . . . . . . . . . . . . 3–10
iii
4
Bridge Configuration Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Device ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–4
Revision ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Class Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Cache Line Size Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Primary Latency Timer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Header Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
4.10 BIST Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
4.11 Base Address Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
4.12 Base Address Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
4.13 Primary Bus Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
4.14 Secondary Bus Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
4.15 Subordinate Bus Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
4.16 Secondary Bus Latency Timer Register . . . . . . . . . . . . . . . . . . . . . . . . 4–8
4.17 I/O Base Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
4.18 I/O Limit Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
4.19 Secondary Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–10
4.20 Memory Base Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11
4.21 Memory Limit Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11
4.22 Prefetchable Memory Base Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11
4.23 Prefetchable Memory Limit Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12
4.24 Prefetchable Base Upper 32 Bits Register . . . . . . . . . . . . . . . . . . . . . . 4–12
4.25 Prefetchable Limit Upper 32 Bits Register . . . . . . . . . . . . . . . . . . . . . . 4–12
4.26 I/O Base Upper 16 Bits Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–13
4.27 I/O Limit Upper 16 Bits Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–13
4.28 Capability Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–13
4.29 Expansion ROM Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . 4–14
4.30 Interrupt Line Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14
4.31 Interrupt Pin Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14
4.32 Bridge Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–15
Extension Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Chip Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Extended Diagnostic Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2
Arbiter Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Extension Window Base 0, 1 Registers . . . . . . . . . . . . . . . . . . . . . . . . . 5–4
Extension Window Limit 0, 1 Registers . . . . . . . . . . . . . . . . . . . . . . . . . 5–4
Extension Window Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
Extension Window Map Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
Secondary Decode Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6
Primary Decode Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
5.10 Port Decode Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
iv
5.11 Buffer Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–9
5.12 Port Decode Map Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
5.13 Clock Run Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–11
5.14 Diagnostic Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–11
5.15 Diagnostic Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
5.16 Arbiter Request Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
5.17 Arbiter Timeout Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–15
5.18 P_SERR Event Disable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–16
5.19 Secondary Clock Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–17
5.20 P_SERR Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–18
5.21 PM Capability ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–18
5.22 PM Next Item Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–19
5.23 Power Management Capabilities Register . . . . . . . . . . . . . . . . . . . . . . 5–19
5.24 Power Management Control/Status Register . . . . . . . . . . . . . . . . . . . . 5–20
5.25 PMCSR Bridge Support Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–21
5.26 Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–21
5.27 HS Capability ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–22
5.28 HS Next Item Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–22
5.29 Hot Swap Control Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–23
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
6
6.1
6.2
6.3
6.4
6.5
Absolute Maximum Ratings Over Operating Temperature Ranges . 6–1
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 6–2
Recommended Operating Conditions for PCI Interface . . . . . . . . . . . 6–2
Electrical Characteristics Over Recommended Operating Conditions 6–3
PCI Clock/Reset Timing Requirements Over Recommended Ranges
of Supply Voltage and Operating Free-Air Temperature . . . . . . . . . . . 6–4
6.6
PCI Timing Requirements Over Recommended Ranges of Supply
Voltage and Operating Free-Air Temperature . . . . . . . . . . . . . . . . . . . . 6–5
6.7
6.8
Parameter Measurement Information . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
PCI Bus Parameter Measurement Information . . . . . . . . . . . . . . . . . . . 6–7
7
Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1
v
List of Illustrations
Figure
2–1
2–2
3–1
3–2
3–3
3–4
3–5
6–1
6–2
6–3
6–4
Title
Page
PCI2250 PGF LQFP Terminal Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
PCI2250 PCM PQFP Terminal Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
PCI AD31–AD0 During Address Phase of a Type 0 Configuration Cycle 3–2
PCI AD31–AD0 During Address Phase of a Type 1 Configuration Cycle 3–3
Bus Hierarchy and Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
Secondary Clock Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
Load Circuit and Voltage Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
PCLK Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
RSTIN Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
Shared-Signals Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
vi
List of Tables
Table
Title
Page
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
PGF LQFP Signal Names Sorted by Terminal Number . . . . . . . . . . . . . . . 2–3
PCM LQFP Signals Sorted by Terminal Number . . . . . . . . . . . . . . . . . . . . 2–4
Signal Names Sorted Alphabetically to PGF Terminal Number . . . . . . . . 2–5
Signal Names Sorted Alphabetically to PCM Terminal Number . . . . . . . . 2–6
Primary PCI System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
Primary PCI Address and Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
Primary PCI Interface Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Secondary PCI System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
Secondary PCI Address and Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
2–10 Secondary PCI Interface Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
2–11 Miscellaneous Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
2–12 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
3–1
4–1
4–2
4–3
4–4
4–5
4–6
5–1
5–2
5–3
5–4
5–5
5–6
5–7
5–8
5–9
PCI Command Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Bridge Configuration Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Bit Field Access Tag Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–4
Secondary Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–10
Bridge Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–15
Chip Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Extended Diagnostic Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2
Arbiter Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Extension Window Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
Extension Window Map Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
Secondary Decode Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6
Primary Decode Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
Port Decode Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Buffer Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–9
5–10 Port Decode Map Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
5–11 Clock Run Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–11
5–12 Diagnostic Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–12
5–13 Diagnostic Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
5–14 Arbiter Request Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
5–15 Arbiter Timeout Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–15
5–16 P_SERR Event Disable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–16
5–17 Secondary Clock Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–17
5–18 P_SERR Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–18
vii
5–19 Power Management Capabilities Register . . . . . . . . . . . . . . . . . . . . . . . . . . 5–19
5–20 Power Management Capabilities Register . . . . . . . . . . . . . . . . . . . . . . . . . . 5–20
5–21 PMCSR Bridge Support Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–21
5–22 Hot Swap Control Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–23
viii
1 Introduction
1.1 Description
The Texas Instruments PCI2250 PCI-to-PCI bridge provides a high performance connection path between two
peripheral component interconnect (PCI) buses. Transactions occur between masters on one PCI bus and targets
on another PCI bus, and the PCI2250 allows bridged transactions to occur concurrently on both buses. The bridge
supports burst-mode transfers to maximize data throughput, and the two bus traffic paths through the bridge act
independently.
The PCI2250 bridge is compliant with the PCI Local Bus Specification, and can be used to overcome the electrical
loading limits of 10 devices per PCI bus and one PCI device per expansion slot by creating hierarchical buses. The
PCI2250 provides two-tier internal arbitration for up to four secondary bus masters and may be implemented with
an external secondary PCI bus arbiter.
The PCI2250 provides compact-PCI (CPCI) hot-swap extended capability, which makes it an ideal solution for
multifunction compact-PCI cards and adapting single function cards to hot-swap compliance.
The PCI2250 bridge is compliant with the PCI-to-PCI Bridge Specification. It can be configured for positive decoding
or subtractive decoding on the primary interface, and provides several additional decode options that make it an ideal
bridge to custom PCI applications. Two extension windows are included, and the PCI2250 provides decoding of serial
and parallel port addresses.
The PCI2250 is compliant with PCI Power Management Interface Specification Revisions 1.0 and 1.1. Also, the
PCI2250offersPCICLKRUNbridgingsupportforlow-powermobileanddockingapplications. ThePCI2250hasbeen
designed to lead the industry in power conservation. An advanced CMOS process is utilized to achieve low system
power consumption while operating at PCI clock rates up to 33 MHz.
1.2 Features
The PCI2250 supports the following features:
•
•
•
•
•
Configurable for PCI Power Management Interface Specification Revision 1.0 or 1.1 support
Compact-PCI friendly silicon as defined in the Compact-PCI Hot Swap Specification
3.3-V core logic with universal PCI interface compatible with 3.3-V and 5-V PCI signaling environments
Two 32-bit, 33-MHz PCI buses
Provides internal two-tier arbitration for up to four secondary bus masters and supports an external
secondary bus arbiter
•
•
•
•
•
•
•
•
•
Burst data transfers with pipeline architecture to maximize data throughput in both directions
Provides programmable extension windows and port decode options
Independent read and write buffers for each direction
Provides five secondary PCI clock outputs
Predictable latency per PCI Local Bus Specification
Propagates bus locking
Secondary bus is driven low during reset
Provides VGA palette memory and I/O, and subtractive decoding options
Advanced submicron, low-power CMOS technology
1–1
•
•
Fully compliant with PCI-to-PCI Bridge Architecture Specification
Packaged in 160-pin QFP (PCM) and 176-pin thin QFP (PGF)
1.3 Related Documents
•
•
•
•
•
•
Advanced Configuration and Power Interface (ACPI) Revision 1.0
PCI Local Bus Specification Revision 2.2
PCI Mobile Design Guide, Revision 1.0
PCI-to-PCI Bridge Architecture Specification Revision 1.1
PCI Power Management Interface Specification Revision 1.1
PICMG Compact-PCI Hot Swap Specification Revision 1.0
1.4 Ordering Information
ORDERING NUMBER
NAME
PCI–PCI Bridge
VOLTAGE
PACKAGE
160-pin QFP
176-pin LQFP
PCI2250
3.3 V, 5-V tolerant I/Os
1–2
2 Terminal Descriptions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
GND
NC
S_PAR
NC
S_SERR
S_PERR
S_MFUNC
S_STOP
MS0
NC
GND
NC
P_AD8
P_AD9
V
CC
P_AD10
P_AD11
P_AD12
GND
S_DEVSEL
V
CC
S_TRDY
S_IRDY
S_FRAME
GND
P_AD13
P_AD14
P_AD15
V
S_C/BE2
S_AD16
CC
P_C/BE1
P_PAR
P_SERR
P_PERR
GND
V
CC
S_AD17
S_AD18
S_AD19
GND
P_MFUNC
P_STOP
P_DEVSEL
P_TRDY
S_AD20
S_AD21
S_AD22
V
V
CC
CC
P_IRDY
P_FRAME
P_C/BE2
GND
P_AD16
P_AD17
P_AD18
S_AD23
S_C/BE3
S_AD24
GND
S_AD25
S_AD26
V
CC
V
S_AD27
S_AD28
S_AD29
GND
S_AD30
S_AD31
S_REQ0
S_REQ1
NC
CC
P_AD19
P_AD20
P_AD21
GND
P_AD22
P_AD23
P_IDSEL
NC
98
97
96
95
94
93
92
91
P_C/BE3
NC
GND
S_REQ2
90
89
NC
CC
V
Figure 2–1. PCI2250 PGF LQFP Terminal Diagram
2–1
MS0
GND
S_PAR
1
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
GND
2
3
P_AD8
S_SERR
4
P_AD9
S_PERR
S_MFUNC
V
5
CC
P_AD10
P_AD11
P_AD12
GND
6
S_STOP
7
S_DEVSEL
V
8
CC
9
S_TRDY
S_IRDY
S_FRAME
GND
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
P_AD13
P_AD14
P_AD15
V
CC
S_C/BE2
S_AD16
P_C/BE1
V
P_PAR
P_SERR
CC
A_AD17
P_PERR
GND
S_AD18
S_AD19
GND
S_AD20
S_AD21
P_MFUNC
P_STOP
P_DEVSEL
P_TRDY
S_AD22
V
V
CC
98
CC
P_IRDY
P_FRAME
P_C/BE2
GND
S_AD23
S_C/BE3
97
96
S_AD24
95
94
GND
S_AD25
S_AD26
93
P_AD16
P_AD17
92
P_AD18
V
91
30
31
32
33
34
35
36
37
38
39
CC
V
S_AD27
90
89
88
87
86
85
84
83
82
81
CC
P_AD19
P_AD20
P_AD21
GND
P_AD22
P_AD23
P_IDSEL
S_AD28
S_AD29
GND
S_AD30
S_AD31
S_REQ0
S_REQ1
S_REQ2
P_C/BE3
GND
V
40
CC
Figure 2–2. PCI2250 PCM PQFP Terminal Diagram
2–2
Table 2–1. PGF LQFP Signal Names Sorted by Terminal Number
TERM. NO.
1
SIGNAL NAME
GND
TERM. NO.
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
SIGNAL NAME
GND
TERM. NO.
89
SIGNAL NAME
GND
TERM. NO.
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
SIGNAL NAME
GND
2
NC
NC
90
NC
NC
3
S_PAR
NC
S_REQ3
NC
91
P_C/BE3
NC
P_C/BE0
NC
4
92
5
S_SERR
S_PERR
S_MFUNC
S_STOP
S_DEVSEL
S_GNT0
S_GNT1
S_GNT2
93
P_IDSEL
P_AD23
P_AD22
GND
P_AD7
P_AD6
6
94
7
95
V
CC
8
V
CC
96
P_AD5
P_AD4
GND
9
S_GNT3
S_RST
S_CFN
GND
97
P_AD21
P_AD20
P_AD19
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
V
CC
98
S_TRDY
S_IRDY
S_FRAME
GND
99
P_AD3
P_AD2
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
V
CC
S_CLK
P_AD18
P_AD17
P_AD16
GND
V
CC
S_V
CCP
P_AD1
P_AD0
S_AD0
GND
S_C/BE2
S_AD16
S_CLKOUT0
GND
V
CC
S_CLKOUT1
P_C/BE2
P_FRAME
P_IRDY
S_AD17
S_AD18
S_AD19
GND
V
CC
S_AD1
S_AD2
S_AD3
S_CLKOUT2
GND
V
CC
S_CLKOUT3
P_TRDY
P_DEVSEL
P_STOP
P_MFUNC
GND
V
CC
S_AD20
S_AD21
S_AD22
V
CC
S_AD4
S_AD5
S_AD6
GND
S_CLKOUT4
NO/HSLED
GOZ
V
CC
S_AD23
S_C/BE3
S_AD24
GND
P_RST
P_PERR
P_SERR
P_PAR
S_AD7
S_C/BE0
S_AD8
GND
P_CLK
P_V
CCP
P_C/BE1
V
CC
S_AD25
S_AD26
P_GNT
P_REQ
P_AD31
GND
V
CC
S_AD9
S_AD10
S_AD11
GND
P_AD15
P_AD14
P_AD13
GND
V
CC
S_AD27
S_AD28
S_AD29
GND
P_AD30
P_AD29
P_AD28
S_AD12
S_AD13
P_AD12
P_AD11
P_AD10
V
CC
S_AD30
S_AD31
S_REQ0
S_REQ1
NC
V
CC
S_AD14
S_AD15
GND
P_AD27
P_AD26
P_AD25
NC
V
CC
P_AD9
P_AD8
NC
S_C/BE1
NC
S_REQ2
NC
P_AD24
NC
GND
NC
MS1/BPCC
NC
V
CC
V
CC
MS0
V
CC
2–3
Table 2–2. PCM LQFP Signals Sorted by Terminal Number
TERM. NO.
1
SIGNAL NAME
GND
TERM. NO.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
SIGNAL NAME
GND
TERM. NO.
81
SIGNAL NAME
GND
TERM. NO.
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
SIGNAL NAME
GND
2
S_PAR
S_REQ3
S_GNT0
S_GNT1
S_GNT2
82
P_C/BE3
P_IDSEL
P_AD23
P_AD22
GND
P_C/BE0
P_AD7
P_AD6
3
S_SERR
S_PERR
S_MFUNC
S_STOP
S_DEVSEL
83
4
84
5
85
V
CC
6
V
CC
86
P_AD5
P_AD4
GND
7
S_GNT3
S_RST
S_CFN
GND
87
P_AD21
P_AD20
P_AD19
8
V
CC
88
9
S_TRDY
S_IRDY
S_FRAME
GND
89
P_AD3
P_AD2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
90
V
CC
S_CLK
91
P_AD18
P_AD17
P_AD16
GND
V
CC
S_V
CCP
92
P_AD1
P_AD0
S_AD0
GND
S_C/BE2
S_AD16
S_CLKOUT0
GND
93
94
V
CC
S_CLKOUT1
95
P_C/BE2
P_FRAME
P_IRDY
S_AD17
S_AD18
S_AD19
GND
V
CC
96
S_AD1
S_AD2
S_AD3
S_CLKOUT2
GND
97
98
V
CC
S_CLKOUT3
99
P_TRDY
P_DEVSEL
P_STOP
P_MFUNC
GND
V
CC
S_AD20
S_AD21
S_AD22
V
CC
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
S_AD4
S_AD5
S_AD6
GND
S_CLKOUT4
NO/HSLED
GOZ
V
CC
S_AD23
S_C/BE3
S_AD24
GND
P_RST
P_PERR
P_SERR
P_PAR
S_AD7
S_C/BE0
S_AD8
GND
P_CLK
P_V
CCP
P_C/BE1
V
CC
S_AD25
S_AD26
P_GNT
P_REQ
P_AD31
GND
V
CC
S_AD9
S_AD10
S_AD11
GND
P_AD15
P_AD14
P_AD13
GND
V
CC
S_AD27
S_AD28
S_AD29
GND
P_AD30
P_AD29
P_AD28
S_AD12
S_AD13
P_AD12
P_AD11
P_AD10
V
CC
S_AD30
S_AD31
S_REQ0
S_REQ1
S_REQ2
V
CC
S_AD14
S_AD15
GND
P_AD27
P_AD26
P_AD25
P_AD24
V
CC
P_AD9
P_AD8
GND
S_C/BE1
MS1/BPCC
V
CC
V
CC
MS0
V
CC
2–4
Table 2–3. Signal Names Sorted Alphabetically to PGF Terminal Number
SIGNAL NAME
GND
TERM. NO.
1
SIGNAL NAME
P_AD1
TERM. NO.
146
144
143
141
140
138
137
128
127
125
124
123
121
120
119
103
102
101
99
SIGNAL NAME
P_REQ
TERM. NO.
75
SIGNAL NAME
S_CLKOUT0
S_CLKOUT1
S_CLKOUT2
S_CLKOUT3
S_CLKOUT4
S_DEVSEL
S_FRAME
S_GNT0
TERM. NO.
59
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GOZ
MS0
MS1/BPCC
NC
14
P_AD2
P_RST
70
61
21
P_AD3
P_SERR
P_STOP
115
111
109
73
63
29
P_AD4
65
36
P_AD5
P_TRDY
67
45
P_AD6
P_V
CCP
9
56
P_AD7
S_AD0
148
150
151
152
154
155
156
158
160
162
163
164
166
167
169
170
16
13
60
P_AD8
S_AD1
49
64
P_AD9
S_AD2
S_GNT1
50
71
P_AD10
P_AD11
P_AD12
P_AD13
P_AD14
P_AD15
P_AD16
P_AD17
P_AD18
P_AD19
P_AD20
P_AD21
P_AD22
P_AD23
P_AD24
P_AD25
P_AD26
P_AD27
P_AD28
P_AD29
P_AD30
P_AD31
P_C/BE0
P_C/BE1
P_C/BE2
P_C/BE3
P_CLK
S_AD3
S_GNT2
51
77
S_AD4
S_GNT3
53
89
S_AD5
S_IRDY
12
96
S_AD6
S_MFUNC
S_PAR
7
104
113
122
130
133
142
149
157
165
171
69
S_AD7
3
S_AD8
S_PERR
6
S_AD9
S_REQ0
39
S_AD10
S_AD11
S_AD12
S_AD13
S_AD14
S_AD15
S_AD16
S_AD17
S_AD18
S_AD19
S_AD20
S_AD21
S_AD22
S_AD23
S_AD24
S_AD25
S_AD26
S_AD27
S_AD28
S_AD29
S_AD30
S_AD31
S_C/BE0
S_C/BE1
S_C/BE2
S_C/BE3
S_CFN
S_CLK
S_REQ1
40
S_REQ2
42
S_REQ3
47
98
S_RST
54
97
S_SERR
5
95
S_STOP
8
94
S_TRDY
11
86
18
S_V
CCP
58
132
174
2
84
19
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
10
CC
83
20
17
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
82
22
25
NC
4
80
23
32
NC
41
79
24
44
NC
43
78
26
52
NC
46
76
28
62
NC
48
135
117
105
91
30
66
NC
85
31
81
NC
87
33
88
NC
90
34
100
108
118
126
139
145
153
161
168
176
NC
92
72
35
NC
129
131
134
136
173
175
68
P_DEVSEL
P_FRAME
P_GNT
110
106
74
37
NC
38
NC
159
172
15
NC
P_IDSEL
P_IRDY
P_MFUNC
P_PAR
93
NC
107
112
116
114
NC
27
NO/HSLED
P_AD0
55
147
P_PERR
57
2–5
Table 2–4. Signal Names Sorted Alphabetically to PCM Terminal Number
SIGNAL NAME
GND
TERM. NO.
1
SIGNAL NAME
P_AD13
P_AD14
P_AD15
P_AD16
P_AD17
P_AD18
P_AD19
P_AD20
P_AD21
P_AD22
P_AD23
P_AD24
P_AD25
P_AD26
P_AD27
P_AD28
P_AD29
P_AD30
P_AD31
P_C/BE0
P_C/BE1
P_C/BE2
P_C/BE3
P_CLK
TERM. NO.
111
110
109
93
SIGNAL NAME
S_AD2
TERM. NO.
137
138
140
141
142
144
146
148
149
150
152
153
155
156
14
SIGNAL NAME
S_CLKOUT4
S_DEVSEL
S_FRAME
S_GNT0
S_GNT1
S_GNT2
S_GNT3
S_IRDY
TERM. NO.
61
7
GND
12
S_AD3
GND
19
S_AD4
11
GND
27
S_AD5
43
44
45
47
10
5
GND
34
92
S_AD6
GND
41
91
S_AD7
GND
50
89
S_AD8
GND
54
88
S_AD9
GND
58
87
S_AD10
S_AD11
S_AD12
S_AD13
S_AD14
S_AD15
S_AD16
S_AD17
S_AD18
S_AD19
S_AD20
S_AD21
S_AD22
S_AD23
S_AD24
S_AD25
S_AD26
S_AD27
S_AD28
S_AD29
S_AD30
S_AD31
S_C/BE0
S_C/BE1
S_C/BE2
S_C/BE3
S_CFN
S_MFUNC
S_PAR
GND
65
85
2
GND
71
84
S_PERR
S_REQ0
S_REQ1
S_REQ2
S_REQ3
S_RST
4
GND
81
79
37
38
39
42
48
3
GND
86
78
GND
94
77
GND
103
112
119
121
128
135
143
151
157
63
76
GND
74
16
GND
73
17
S_SERR
S_STOP
S_TRDY
GND
72
18
6
GND
70
20
9
GND
122
107
95
21
S_V
CCP
52
8
GND
22
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
CC
GND
24
15
23
30
40
46
56
60
75
80
90
98
108
116
125
131
139
147
154
160
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
GND
82
26
GOZ
66
28
MS0
120
159
62
P_DEVSEL
P_FRAME
P_GNT
100
96
29
MS1/BPCC
NO/HSLED
P_AD0
P_AD1
P_AD2
P_AD3
P_AD4
P_AD5
P_AD6
P_AD7
P_AD8
P_AD9
P_AD10
P_AD11
P_AD12
31
68
32
133
132
130
129
127
126
124
123
118
117
115
114
113
P_IDSEL
P_IRDY
P_MFUNC
P_PAR
83
33
97
35
102
106
104
69
36
145
158
13
P_PERR
P_REQ
P_RST
64
25
P_SERR
P_STOP
P_TRDY
105
101
99
49
S_CLK
51
S_CLKOUT0
S_CLKOUT1
S_CLKOUT2
S_CLKOUT3
53
P_V
CCP
67
55
S_AD0
S_AD1
134
136
57
59
2–6
Table 2–5. Primary PCI System
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
Primary PCI bus clock. P_CLK provides timing for all transactions on the primary PCI bus. All
primary PCI signals are sampled at rising edge of P_CLK.
P_CLK
66
64
72
70
I
PCI reset. When the primary PCI bus reset is asserted, P_RST causes the bridge to put all output
buffers in a high-impedance state and reset all internal registers. When asserted, the device is
completely nonfunctional. During P_RST, the secondary interface is driven low and NO/HSLED
is driven high if hot-swap is enabled. After P_RST is deasserted, the bridge is in its default state.
I
P_RST
Table 2–6. Primary PCI Address and Data
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
P_AD31
P_AD30
P_AD29
P_AD28
P_AD27
P_AD26
P_AD25
P_AD24
P_AD23
P_AD22
P_AD21
P_AD20
P_AD19
P_AD18
P_AD17
P_AD16
P_AD15
P_AD14
P_AD13
P_AD12
P_AD11
P_AD10
P_AD9
70
72
73
74
76
77
78
79
84
85
87
88
89
91
92
93
109
110
111
113
114
115
117
118
123
124
126
127
129
130
132
133
76
78
79
80
82
83
84
86
94
95
97
98
99
101
102
103
119
120
121
123
124
125
127
128
137
138
140
141
143
144
146
147
Primary address/data bus. These signals make up the multiplexed PCI address and data
bus on the primary interface. During the address phase of a primary bus PCI cycle,
P_AD31–P_AD0 contain a 32-bit address or other destination information. During the data
phase, P_AD31–P_AD0 contain data.
I/O
P_AD8
P_AD7
P_AD6
P_AD5
P_AD4
P_AD3
P_AD2
P_AD1
P_AD0
Primary bus commands and byte enables. These signals are multiplexed on the same PCI
terminals. During the address phase of a primary bus cycle, P_C/BE3–P_C/BE0 define the
bus command. During the data phase, this 4-bit bus is used as byte enables. The byte
enables determine which byte paths of the full 32-bit data bus carry meaningful data.
P_C/BE0applies to byte 0 (P_AD7–P_AD0), P_C/BE1 applies to byte 1 (P_AD15–P_AD8),
P_C/BE2 applies to byte 2 (P_AD23–P_AD16), and P_C/BE3 applies to byte 3
(P_AD31–P_AD24).
82
95
107
122
91
P_C/BE3
P_C/BE2
P_C/BE1
P_C/BE0
105
117
135
I/O
2–7
Table 2–7. Primary PCI Interface Control
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
Primary device select. The bridge asserts P_DEVSEL to claim a PCI cycle as the target
device. As a PCI initiator on the primary bus, the bridge monitors P_DEVSEL until a target
responds. If no target responds before a time-out occurs, then the bridge terminates the cycle
with a master abort.
P_DEVSEL
100
110
I/O
Primary cycle frame. P_FRAME is driven by the initiator of a primary bus cycle. P_FRAME
is asserted to indicate that a bus transaction is beginning, and data transactions continue
while this signal is asserted. When P_FRAME is deasserted, the primary bus transaction is
in the final data phase.
96
68
106
74
I/O
I
P_FRAME
P_GNT
Primarybusgranttobridge. P_GNTis drivenby theprimary PCI bus arbiter togrant the bridge
access to the primary PCI bus after the current data transaction has completed. P_GNT may
or may not follow a primary bus request, depending on the primary bus parking algorithm.
Primary initialization device select. P_IDSEL selects the bridge during configuration space
accesses. P_IDSELcanbeconnectedtooneoftheupper16PCIaddresslinesontheprimary
PCI bus.
P_IDSEL
83
93
I
Note: There is no IDSEL signal interfacing the secondary PCI bus; thus, the entire
configuration space of the bridge can only be accessed from the primary bus.
Primaryinitiator ready. P_IRDY indicates the ability of the primary bus initiator to complete the
current data phase of the transaction. A data phase is completed on a rising edge of P_CLK
wherebothP_IRDYandP_TRDYareasserted. UntilP_IRDYandP_TRDYarebothsampled
asserted, wait states are inserted.
P_IRDY
P_PAR
97
107
116
I/O
I/O
Primary parity. In all primary bus read and write cycles, the bridge calculates even parity
acrosstheP_ADandP_C/BEbuses. AsaninitiatorduringPCIwritecycles,thebridgeoutputs
thisparityindicatorwithaone-P_CLKdelay. AsatargetduringPCIreadcycles, thecalculated
parity is compared to the initiator parity indicator; a miscompare can result in a parity error
assertion (P_PERR).
106
Primary parity error indicator. P_PERR is driven by a primary bus PCI device to indicate that
calculated parity does not match P_PAR when P_PERR is enabled through bit 6 of the
command register (offset 04h, see Section 4.3).
104
69
114
75
I/O
O
P_PERR
P_REQ
Primary PCI bus request. P_REQ is asserted by the bridge to request access to the primary
PCI bus as an initiator.
Primary system error. Output pulsed from the bridge when enabled through the command
register (offset 04h, see Section 4.3) indicating a system error has occurred. The bridge need
not be the target of the primary PCI cycle to assert this signal. When bit 1 is enabled in the
bridge control register (offset 3Eh, see Section 4.32), this signal will also pulse indicating that
a system error has occurred on one of the subordinate buses downstream from the bridge.
P_SERR
105
115
O
Primary cycle stop signal. This signal is driven by a PCI target to request the initiator to stop
the current primary bus transaction. This signal is used for target disconnects and is
commonly asserted by target devices which do not support burst data transfers.
P_STOP
P_TRDY
101
99
111
109
I/O
I/O
Primary target ready. P_TRDY indicates the ability of the primary bus target to complete the
current data phase of the transaction. A data phase is completed on the rising edge of P_CLK
where both P_IRDY and P_TRDY are asserted. Until P_IRDY and P_TRDY are both sample
asserted, wait states are inserted.
2–8
Table 2–8. Secondary PCI System
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
61
59
57
55
53
67
65
63
61
59
S_CLKOUT4
S_CLKOUT3
S_CLKOUT2
S_CLKOUT1
S_CLKOUT0
Secondary PCI bus clocks. Provide timing for all transactions on the secondary PCI bus.
Each secondary bus device samples all secondary PCI signals at the rising edge of its
corresponding S_CLKOUT input.
O
Secondary PCI bus clock input. This input syncronizes the PCI2250 to the secondary bus
clocks.
51
57
I
I
S_CLK
Secondary external arbiter enable. When this signal is high, the secondary external arbiter
is enabled. When the external arbiter is enabled, the S_REQ0 pin is reconfigured as a
secondary bus grant input to the bridge and S_GNT0 is reconfigured as a secondary bus
master request to the external arbiter on the secondary bus.
S_CFN
49
55
Secondary PCI reset. S_RST is a logical OR of P_RST and the state of the secondary bus
reset bit of the bridge control register (offset 3Eh, see Section 4.32). S_RST is asynchronous
with respect to the state of the secondary interface CLK signal.
S_RST
48
54
O
2–9
Table 2–9. Secondary PCI Address and Data
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
36
35
33
32
31
29
28
26
24
22
21
20
18
17
16
14
156
155
153
152
150
149
148
146
144
142
141
140
138
137
136
134
38
37
35
34
33
31
30
28
26
24
23
22
20
19
18
16
170
169
167
166
164
163
162
160
158
156
155
154
152
151
150
148
S_AD31
S_AD30
S_AD29
S_AD28
S_AD27
S_AD26
S_AD25
S_AD24
S_AD23
S_AD22
S_AD21
S_AD20
S_AD19
S_AD18
S_AD17
S_AD16
S_AD15
S_AD14
S_AD13
S_AD12
S_AD11
S_AD10
S_AD9
Secondary address/data bus. These signals make up the multiplexed PCI address and data
bus on the secondary interface. During the address phase of a secondary bus PCI cycle,
S_AD31–S_AD0 contain a 32-bit address or other destination information. During the data
phase, S_AD31–S_AD0 contain data.
I/O
S_AD8
S_AD7
S_AD6
S_AD5
S_AD4
S_AD3
S_AD2
S_AD1
S_AD0
Secondary bus commands and byte enables. These signals are multiplexed on the same PCI
terminals.During the address phase of a secondary bus cycle, S_C/BE3–S_C/BE0definethe
buscommand. Duringthedataphase, this4-bitbusisusedasbyteenables. Thebyteenables
determinewhich byte paths of the full 32-bit data bus carry meaningful data. S_C/BE0 applies
to byte 0 (S_AD7–S_AD0), S_C/BE1 applies to byte 1 (S_AD15–S_AD8), S_C/BE2 applies
to byte 2 (S_AD23–S_AD16), and S_C/BE3 applies to byte 3 (S_AD31–S_AD24).
S_C/BE3
S_C/BE2
S_C/BE1
S_C/BE0
25
13
158
145
27
15
172
159
I/O
2–10
Table 2–10. Secondary PCI Interface Control
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
Secondary device select. The bridge asserts S_DEVSEL to claim a PCI cycle as the target
device.AsaPCIinitiatoronthesecondarybus, thebridgemonitorsS_DEVSELuntilatarget
responds. Ifnotargetrespondsbeforeatimeoutoccurs, thenthebridgeterminatesthecycle
with a master abort.
S_DEVSEL
7
9
I/O
Secondary cycle frame. S_FRAME is driven by the initiator of a secondary bus cycle.
S_FRAME is asserted to indicate that a bus transaction is beginning and data transfers
continue while S_FRAME is asserted. When S_FRAME is deasserted, the secondary bus
transaction is in the final data phase.
S_FRAME
11
13
I/O
O
Secondarybusgranttothebridge. Thebridgeprovidesinternalarbitrationandthesesignals
areusedtograntpotentialsecondaryPCImastersaccesstothebus. Fivepotentialinitiators
(including the bridge) can be located on the secondary PCI bus.
S_GNT3
S_GNT2
S_GNT1
S_GNT0
47
45
44
43
53
51
50
49
Whenthe internal arbiter is disabled, S_GNT0 is reconfigured as an external secondary bus
request signal for the bridge.
Secondary initiator ready. S_IRDY indicates the ability of the secondary bus initiator to
complete the current data phase of the transaction. A data phase is completed on a rising
edge of S_CLK where both S_IRDY and S_TRDY are asserted. Until S_IRDY and S_TRDY
are both sample asserted, wait states are inserted.
S_IRDY
10
12
I/O
Secondary parity. In all secondary bus read and write cycles, the bridge calculates even
parityacrosstheS_ADandS_C/BEbuses. AsaninitiatorduringPCIwritecycles, thebridge
outputs this parity indicator with a one-S_CLK delay. As a target during PCI read cycles, the
calculated parity is compared to the initiator parity indicator. A miscompare can result in a
parity error assertion (S_PERR).
S_PAR
2
4
3
6
I/O
I/O
Secondary parity error indicator. S_PERR is driven by a secondary bus PCI device to
indicate that calculated parity does not match S_PAR when S_PERR is enabled through
bit 6 of the command register (offset 04h, see Section 4.3).
S_PERR
Secondary PCI bus request signals. The bridge provides internal arbitration, and these
signals are used as inputs from secondary PCI bus initiators requesting the bus. Five
potential initiators (including the bridge) can be located on the secondary PCI bus.
S_REQ3
S_REQ2
S_REQ1
S_REQ0
42
39
38
37
47
42
40
39
I
When the internal arbiter is disabled, the S_REQ0 signal is reconfigures as an external
secondary bus grant for the bridge.
Secondary system error. S_SERR is passed through the primary interface by the bridge if
enabledthroughthebridgecontrolregister(offset 3Eh, see Section 4.32). S_SERR is never
asserted by the bridge.
3
6
5
8
I
S_SERR
S_STOP
Secondarycycle stop signal. S_STOP is driven by a PCI target to request theinitiatortostop
the current secondary bus transaction. S_STOP is used for target disconnects and is
commonly asserted by target devices that do not support burst data transfers.
I/O
Secondary target ready. S_TRDY indicates the ability of the secondary bus target to
complete the current data phase of the transaction. A data phase is completed on a rising
edge of S_CLK where both S_IRDY and S_TRDY are asserted. Until S_IRDY and S_TRDY
are both sample asserted, wait states are inserted.
S_TRDY
9
11
I/O
2–11
Table 2–11. Miscellaneous Terminals
TERMINAL
PCM
I/O
DESCRIPTION
PGF
NAME
NUMBER NUMBER
GOZ
NO/HSLED
MS0
63
62
69
68
I
NAND tree enable pin.
I/O
I
NAND tree out when GOZ is asserted. Hot-swap LED when GOZ is deasserted.
Mode select 0
120
132
Mode select 1 when mode select 0 is low, bus power clock control when mode select 0 is
high.
MS1/BPCC
P_MFUNC
S_MFUNC
159
102
5
174
112
7
I
Primary multifunction terminal. This terminal can be configured as P_CLKRUN, P_LOCK,
or HS_ENUM depending on the values of MS0 and MS1.
I/O
I/O
Secondary multifunction terminal. This terminal can be configured as S_CLKRUN,
S_LOCK, or HS_SWITCH depending on the values of MS0 and MS1.
Table 2–12. Power Supply
TERMINAL
DESCRIPTION
PGF NUMBER
NAME
PCM NUMBER
1, 12, 19, 27, 34, 41, 50, 54, 1, 14, 21, 29, 36, 45, 56, 60,
58, 65, 71, 81, 86, 94, 103, 64, 71, 77, 89, 96, 104, 113,
GND
Device ground terminals
112, 119, 121, 128, 135,
143, 151, 157
122, 130, 133, 142, 149,
157, 165, 171
8, 15, 23, 30, 40, 46, 56, 60,
75, 80, 90, 98, 108, 116,
125, 131, 139, 147, 154,
160
10, 17, 25, 32, 44, 52, 62,
66, 81, 88, 100, 108, 118,
126, 139, 145, 153, 161,
168, 176
V
CC
Power-supply terminal for core logic (3.3 V)
Primary bus-signaling environment supply. P_V
protection circuitry on primary bus I/O signals.
is used in
is used in
CCP
P_V
S_V
67
52
73
58
CCP
Secondary bus-signaling environment supply. S_V
protection circuitry on secondary bus I/O signals.
CCP
CCP
2–12
3 Feature/Protocol Descriptions
The following sections give an overview of the PCI2250 PCI-to-PCI bridge features and functionality. Figure 3–1
shows a simplified block diagram of a typical system implementation using the PCI2250.
Host Bus
Memory
CPU
Host
PCI
PCI
Bridge
Device
Device
PCI Bus 0
PCI Option Card
PCI Option Card
PCI2250
PCI Bus 2
PCI Bus 1
PCI
Device
PCI
Device
(Option)
PCI2250
PCI Option Slot
Figure 3–1. System Block Diagram
3.1 Introduction to the PCI2250
The PCI2250 is a bridge between two PCI buses and is compliant with both the PCI Local Bus Specification and the
PCI-to-PCI Bridge Specification. The bridge supports two 32-bit PCI buses operating at a maximum of 33 MHz. The
primary and secondary buses operate independently in either a 3.3-V or 5-V signaling environment. The core logic
of the bridge, however, is powered at 3.3 V to reduce power consumption.
Host software interacts with the bridge through internal registers. These internal registers provide the standard PCI
status and control for both the primary and secondary buses. Many vendor-specific features that exist in the TI
extension register set are included in the bridge. The PCI configuration header of the bridge is only accessible from
the primary PCI interface.
The bridge provides internal arbitration for the four possible secondary bus masters, and provides each with a
dedicated active low request/grant pair (REQ/GNT). The arbiter features a two-tier rotational scheme with the
PCI2250 bridge defaulting to the highest priority tier. The bus parking scheme is also configurable and can be set
to either park grant (GNT) on the bridge or on the last mastering device.
Upon system power up, power-on self-test (POST) software configures the bridge according to the devices that exist
on subordinate buses, and enables the performance-enhancing features of the PCI2250. In a typical system, this is
the only communication with the bridge internal register set.
3–1
3.2 PCI Commands
The bridge responds to PCI bus cycles as a PCI target device based on the decoding of each address phase and
internal register settings. Table 3–1 lists the valid PCI bus cycles and their encoding on the command/byte enables
(C/BE) bus during the address phase of a bus cycle.
Table 3–1. PCI Command Definition
COMMAND
Interrupt acknowledge
Special cycle
C/BE3–C/BE0
0000
0001
0010
0011
I/O read
I/O write
0100
0101
0110
Reserved
Reserved
Memory read
0111
Memory write
1000
1001
1010
1011
Reserved
Reserved
Configuration read
Configuration write
Memory read multiple
Dual address cycle
Memory read line
Memory write and invalidate
1100
1101
1110
1111
The bridge never responds as a PCI target to the interrupt acknowledge, special cycle, dual address cycle, or
reserved commands. The bridge does, however, initiate special cycles on both interfaces when a type 1 configuration
cycle issues the special cycle request. The remaining PCI commands address either memory, I/O, or configuration
space. The bridge accepts PCI cycles by asserting DEVSEL as a medium-speed device, i.e., DEVSEL is asserted
two clock cycles after the address phase.
The PCI2250 converts memory write and invalidate commands to memory write commands when forwarding
transactions from either the primary or secondary side of the bridge.
3.3 Configuration Cycles
The PCI Local Bus Specification defines two types of PCI configuration read and write cycles: type 0 and type 1. The
bridge decodes each type differently. Type 0 configuration cycles are intended for devices on the primary bus, while
type 1 configuration cycles are intended for devices on some hierarchically subordinate bus. The difference between
these two types of cycles is the encoding of the primary PCI (P_AD) bus during the address phase of the cycle.
Figure 3–2 shows the P_AD bus encoding during the address phase of a type 0 configuration cycle. The 6-bit register
number field represents an 8-bit address with the two lower bits masked to 0, indicating a doubleword boundary. This
results in a 256-byte configuration address space per function per device. Individual byte accesses may be selected
within a doubleword by using the P_C/BE signals during the data phase of the cycle.
31
11 10
8
7
2
1
0
0
Function
Number
Register
Number
Reserved
0
Figure 3–2. PCI AD31–AD0 During Address Phase of a Type 0 Configuration Cycle
3–2
The bridge claims only type 0 configuration cycles when its P_IDSEL terminal is asserted during the address phase
of the cycle and the PCI function number encoded in the cycle is 0. If the function number is 1 or greater, the bridge
does not recognize the configuration command. In this case, the bridge does not assert DEVSEL and the
configuration transaction results in a master abort. The bridge services valid type 0 configuration read or write cycles
by accessing internal registers from the configuration header.
Because type 1 configuration cycles are issued to devices on subordinate buses, the bridge claims type 1 cycles
based on the bus number of the destination bus. Figure 3–3 shows the P_AD bus encoding during the address phase
of a type 1 cycle. The device number and bus number fields define the destination bus and device for the cycle.
31
24 23
16 15
11 10
8
7
2
1
0
0
Device
Number
Function
Number
Register
Number
Reserved
Bus Number
0
Figure 3–3. PCI AD31–AD0 During Address Phase of a Type 1 Configuration Cycle
Several bridge configuration registers shown in Table 4–1 are significant when decoding and claiming type 1
configuration cycles. The destination bus number encoded on the P_AD bus is compared to the values programmed
in the bridge configuration registers 18h, 19h, and 1Ah, which are the primary bus number, secondary bus number,
and subordinate bus number registers, respectively. These registers default to 00h and are programmed by host
software to reflect the bus hierarchy in the system (see Figure 3–4 for an example of a system bus hierarchy and how
the PCI2250 bus number registers would be programmed in this case).
When the PCI2250 claims a type 1 configuration cycle that has a bus number equal to its secondary bus number,
the PCI2250 converts the type 1 configuration cycle to a type 0 configuration cycle and asserts the proper S_AD line
as the IDSEL (see Table 3–2). All other type 1 transactions that access a bus number greater than the bridge
secondary bus number but less than or equal to its subordinate bus number are forwarded as type 1 configuration
cycles.
Table 3–2. PCI S_AD31–S_AD16 During Address Phase of a Type 0 Configuration Cycle
SECONDARY IDSEL
S_AD31–S_AD16
S_AD
ASSERTED
DEVICE
NUMBER
0h
1h
0000 0000 0000 0001
0000 0000 0000 0010
0000 0000 0000 0100
0000 0000 0000 1000
0000 0000 0001 0000
0000 0000 0010 0000
0000 0000 0100 0000
0000 0000 1000 0000
0000 0001 0000 0000
0000 0010 0000 0000
0000 0100 0000 0000
0000 1000 0000 0000
0001 0000 0000 0000
0010 0000 0000 0000
0100 0000 0000 0000
1000 0000 0000 0000
0000 0000 0000 0000
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
–
2h
3h
4h
5h
6h
7h
8h
9h
Ah
Bh
Ch
Dh
Eh
Fh
10h–1Eh
3–3
PCI Bus 0
PCI2250
Primary Bus
Secondary Bus
Subordinate Bus
PCI2250
Primary Bus
Secondary Bus
Subordinate Bus
00h
01h
02h
00h
03h
03h
PCI Bus 1
PCI Bus 3
PCI2250
Primary Bus
Secondary Bus
Subordinate Bus
01h
02h
02h
PCI Bus 2
Figure 3–4. Bus Hierarchy and Numbering
3.4 Special Cycle Generation
The bridge is designed to generate special cycles on both buses through a type 1 cycle conversion. During a type 1
configuration cycle, if the bus number field matches the bridge secondary bus number, then the device number field
is1Fh, thefunctionnumberfieldis07h, andthebridgegeneratesaspecialcycleonthesecondarybuswithamessage
that matches the type 1 configuration cycle data. If the bus number is a subordinate bus and not the secondary bus,
then the bridge passes the type 1 special cycle request through to the secondary interface along with the proper
message.
Special cycles are never passed through the bridge. Type 1 configuration cycles with a special cycle request can
propagate in both directions.
3.5 Secondary Clocks
The PCI2250 provides five secondary clock outputs (S_CLKOUT[0:4]). Four are provided for clocking secondary
devices. The fifth clock should be routed back into the PCI2250 S_CLK input to ensure all secondary bus devices
see the same clock.
3–4
S_CLK
PCI2250
S_CLKOUT4
S_CLKOUT3
PCI
Device
PCI
Device
S_CLKOUT2
S_CLKOUT1
PCI
Device
PCI
Device
S_CLKOUT0
Figure 3–5. Secondary Clock Block Diagram
3.6 Bus Arbitration
The PCI2250 implements bus request (P_REQ) and bus grant (P_GNT) terminals for primary bus arbitration. Four
secondary bus requests and four secondary bus grants are provided on the secondary of the PCI2250. Five potential
initiators, including the bridge, can be located on the secondary bus. The PCI2250 provides a two-tier arbitration
scheme on the secondary bus for priority bus-master handling.
The two-tier arbitration scheme improves performance in systems in which master devices do not all require the same
bandwidth. Any master that requires frequent use of the bus can be programmed to be in the higher priority tier.
3.6.1 Primary Bus Arbitration
The PCI2250, acting as an initiator on the primary bus, asserts P_REQ when forwarding transactions upstream to
the primary bus. In the upstream direction, as long as a posted write data or a delayed transaction request is in the
queue, the PCI2250 keeps P_REQ asserted. If a target disconnect, a target retry, or a target abort is received in
response to a transaction initiated on the primary bus by the PCI2250, P_REQ is deasserted for two PCI clock cycles.
When the primary bus arbiter asserts P_GNT in response to a P_REQ from the PCI2250, the device initiates a
transaction on the primary bus during the next PCI clock cycle after the primary bus is sampled idle.
When P_REQ is not asserted and the primary bus arbiter asserts P_GNT to the PCI2250, the device responds by
parking the P_AD31–P_AD0 bus, the C/BE3–C/BE0 bus, and primary parity (P_PAR) by driving them to valid logic
levels. If the PCI2250 is parking the primary bus and wants to initiate a transaction on the bus, then it can start the
transaction on the next PCI clock by asserting the primary cycle frame (P_FRAME) while P_GNT is still asserted. If
P_GNT is deasserted, then the bridge must rearbitrate for the bus to initiate a transaction.
3.6.2 Internal Secondary Bus Arbitration
S_CFN controls the state of the secondary internal arbiter. The internal arbiter can be enabled by pulling S_CFN low
or disabled by pulling S_CFN high. The PCI2250 provides four secondary bus request terminals and four secondary
3–5
bus grant terminals. Including the bridge, there are a total of five potential secondary bus masters. These request
and grant signals are connected to the internal arbiter. When an external arbiter is implemented, S_REQ3–S_REQ0
and S_GNT3–S_GNT0 are placed in a high impedance mode.
3.6.3 External Secondary Bus Arbitration
An external secondary bus arbiter can be used instead of the PCI2250 internal arbiter. When using an external arbiter,
the PCI2250’s internal arbiter should be disabled by pulling S_CFN high.
When an external secondary bus arbiter is used, the PCI2250 internally reconfigures the S_REQ0 and S_GNT0
signals so that S_REQ0 becomes the secondary bus grant for the bridge and S_GNT0 becomes the secondary bus
request for the bridge. This is done because S_REQ0 is an input and can thus be used to provide the grant input to
the bridge, and S_GNT0 is an output and can thus provide the request output from the bridge.
When an external arbiter is used, all unused secondary bus grant outputs (S_GNT3–S_GNT1) are placed in a high
impedance mode. Any unused secondary bus request inputs (S_REQ3–S_REQ1) should be pulled high to prevent
the inputs from oscillating.
3.7 Decode Options
The PCI2250 supports positive, subtractive, and negative decoding but defaults to positive decoding on the primary
interface and negative decoding on the secondary bus. Positive decoding is a method of address decoding in which
a device responds only to accesses within an assigned address range. Negative decoding is a method of address
decoding in which a device responds only to accesses outside an assigned address range. Subtractive decoding is
a method of address decoding in which a device responds to accesses not claimed by any other devices on the bus.
Subtractive decoding can be enabled on the primary bus or the secondary bus.
3.8 Extension Windows With Programmable Decoding
The PCI2250 provides two programmable 32-bit extension windows. Each window can be programmed to be a
prefetchable memory window, a nonprefetchable memory window, or an I/O window. The TI extension memory
windows have a 4K-byte granularity, and the I/O windows have a doubleword granularity. These extension windows
can be positively decoded on either the primary bus or secondary bus.
The standard PCI-to-PCI bridge memory and I/O windows specified by the PCI-to-PCI Bridge Specification have a
1M-byte and 4K-byte granularity, respectively (see Section 4.20, Memory Base Register and Section 4.26, I/O Base
Upper 16 Bits Register). The TI extension windows provide smaller granularity for memory and I/O windows. The
extension windows’ granularity matches the requirements of CardBus card windows, which also have 4K-byte
granularity for memory windows and doubleword granularity for I/O windows. When a CardBus I/O card is sitting
behind the bridge, the smaller doubleword I/O window granularity with the extension windows allows a smaller I/O
window than the 4K-byte window with the standard I/O base and limit registers.
A common I/O base address for popular sound cards is 300h–303h. Using the TI extension windows and configuring
the base I/O address for 300h establishes a 4-byte I/O address window from 300h–303h for communicating with the
sound card. Using the bridge’s standard I/O base register requires a minimum 4K-byte window of memory.
The extension windows can be excluded from the primary bus decoding, thus creating a hole in a primary window
address range.
3.9 System Error Handling
The PCI2250 can be configured to signal a system error (SERR) under a variety of conditions. The P_SERR event
disable register (offset 64h, see Section 5.18) and the P_SERR status register (offset 6Ah, see Section 5.20) provide
control and status bits for each condition for which the bridge can signal SERR. These individual bits enable SERR
reporting for both downstream and upstream transactions.
By default, the PCI2250 will not signal SERR. If the PCI2250 is configured to signal SERR by setting bit 8 of the
command register (offset 04h, see Section 4.3), then the bridge signals SERR if any of the error conditions in the
3–6
P_SERR event disable register occur and that condition is enabled. By default, all error conditions are enabled in the
P_SERR event disable register. When the bridge signals SERR, bit 14 of the secondary status register (offset 1Eh,
see Section 4.19) is set.
3.9.1 Posted Write Parity Error
If bit 1 in the P_SERR event disable register (offset 64h, see Section 5.18) is 0, then parity errors on the target bus
during a posted write are passed to the initiating bus as an SERR. When this occurs, bit 1 of the P_SERR status
register (offset 6Ah, see Section 5.20) is set. The status bit is cleared by writing a 1.
3.9.2 Posted Write Timeout
If bit 2 in the P_SERR event disable register (offset 64h, see Section 5.18) is 0 and the retry timer expires while
attempting to complete a posted write, then the PCI2250 signals SERR on the initiating bus. When this occurs, bit 2
of the P_SERR status register (offset 6Ah, see Section 5.20) is set. The status bit is cleared by writing a 1.
3.9.3 Target Abort on Posted Writes
Ifbit3intheP_SERReventdisableregister(offset 64h, see Section 5.18) is 0 and the bridge gets a target abort during
a posted write transaction, then the PCI2250 signals SERR on the initiating bus. When this occurs, bit 3 of the
P_SERR status register (offset 6Ah, see Section 5.20) is set. The status bit is cleared by writing a 1.
3.9.4 Master Abort on Posted Writes
If bit 4 in the P_SERR event disable register (offset 64h, see Section 5.18) is 0 and a posted write transaction results
in a master abort, then the PCI2250 signals SERR on the initiating bus. When this occurs, bit 4 of the P_SERR status
register (offset 6Ah, see Section 5.20) is set. The status bit is cleared by writing a 1.
3.9.5 Master Delayed Write Timeout
If bit 5 in the P_SERR event disable register (offset 64h, see Section 5.18) is 0 and the retry timer expires while
attempting to complete a delayed write, then the PCI2250 signals SERR on the initiating bus. When this occurs, bit 5
of the P_SERR status register (offset 6Ah, see Section 5.20) is set. The status bit is cleared by writing a 1.
3.9.6 Master Delayed Read Timeout
If bit 6 in the P_SERR event disable register (offset 64h, see Section 5.18) is 0 and the retry timer expires while
attempting to complete a delayed read, then the PCI2250 signals SERR on the initiating bus. When this occurs, bit 6
of the P_SERR status register (offset 6Ah, see Section 5.20) is set. The status bit is cleared by writing a 1.
3.9.7 Secondary SERR
The PCI2250 passes SERR from the secondary bus to the primary bus if it is enabled for SERR response (bit 8 in
the command register is 1) and bit 1 in the bridge control register (offset 3Eh, see Section 4.32) is set.
3.10 Parity Handling and Parity Error Reporting
The PCI2250 can be configured to pass parity or provide parity via bit 14 of the diagnostic control register (offset 5Ch,
see Section 5.14). When this bit is cleared to 0, the bridge is enabled for passing parity errors. Parity error passing
is the default mode in the bridge. The following parity conditions result in the bridge signaling an error.
3.10.1 Address Parity Error
If the parity error response bit (bit 6) in the command register (offset 04h, see Section 4.3) is set, then the PCI2250
signals SERR on address parity errors and target abort transactions.
3–7
3.10.2 Data Parity Error
If the parity error response bit (bit 6) in the command register (offset 04h, see Section 4.3) is set, then the PCI2250
signalsPERR when it receives bad data. When the bridge detects bad parity, bit 15 (detected parity error) in the status
register (offset 06h, see Section 4.4) is set.
If the bridge is configured to respond to parity errors via bit 6 in the command register, then the data parity error
detected bit (bit 8 in the status register) is set when the bridge detects bad parity. The data parity error detected bit
is also set when the bridge, as a bus master, asserts PERR or detects PERR.
3.11 Master and Target Abort Handling
If the PCI2250 receives a target abort during a write burst, then it signals target abort back on the initiator bus. If it
receives a target abort during a read burst, then it provides all of the valid data on the initiator bus and disconnects.
Target aborts for posted and nonposted transactions are reported as specified in the PCI-to-PCI Bridge Specification.
MasterabortsforpostedandnonpostedtransactionsarereportedasspecifiedinthePCI-to-PCIBridgeSpecification.
If a transaction is attempted on the primary bus after a secondary reset is asserted, then the PCI2250 follows bit 5
(master abort mode bit setting) in the bridge control register (offset 3Eh, see Section 4.32) for reporting errors.
3.12 Discard Timer
The PCI2250 is free to discard the data or status of a delayed transaction that was completed with a delayed
10
15
transaction termination when a bus master has not repeated the request within 2 or 2 PCI clocks (approximately
15
30 µs and 993 µs, respectively). The PCI Local Bus Specification recommends that a bridge wait 2 PCI clocks
before discarding the transaction data or status.
The PCI2250 implements a discard timer for use in delayed transactions. After a delayed transaction is completed
on the destination bus, the bridge may discard it under two conditions. The first condition occurs when a read
transaction is made to a region of memory that that is inside a defined prefetchable memory region, or when the
command is a memory read line or a memory read multiple, implying that the memory region is prefetchable. The
other condition occurs when the master originating the transaction (either a read or a write, prefetchable or
10
15
nonprefetchable) has not retried the transaction within 2 or 2 clocks. The number of clocks is tracked by a timer
referred to as the discard timer. When the discard timer expires, the bridge is required to discard the data. The
15
10
PCI2250 default value for the discard timer is 2 clocks; however, this value can be set to 2 clocks by setting bit 9
in the bridge control register (offset 3Eh, see Section 4.32). For more information on the discard timer, see error
conditions in PCI Local Bus Specification.
3.13 Delayed Transactions
The bridge supports delayed transactions as defined in the PCI Local Bus Specification. A target must be able to
complete the initial data phase in 16 PCI clocks or less from the assertion of the cycle frame (FRAME), and
subsequent data phases must complete in 8 PCI clocks or less. A delayed transaction consists of three phases:
•
•
•
An initiator device issues a request.
The target completes the request on the destination bus and signals the completion to the initiator.
The initiator completes the request on the originating bus.
If the bridge is the target of a PCI transaction and it must access a slow device to write or read the requested data,
and the transaction takes longer than 16 clocks, then the bridge must latch the address, the command, and the byte
enables, and then issue a retry to the initiator. The initiator must end the transaction without any transfer of data and
is required to retry the transaction later using the same address, command, and byte enables. This is the first phase
of the delayed transaction.
During the second phase, if the transaction is a read cycle, then the bridge fetches the requested data on the
destination bus, stores it internally, and obtains the completion status, thus completing the transaction on the
3–8
destination bus. If it is a write transaction, then the bridge writes the data and obtains the completion status, thus
completing the transaction on the destination bus. The bridge stores the completion status until the master on the
initiating bus retries the initial request.
During the third phase, the initiator rearbitrates for the bus. When the bridge sees the initiator retry the transaction,
it compares the second request to the first request. If the address, command, and byte enables match the values
latched in the first request, then the completion status (and data if the request was a read) is transferred to the initiator.
At this point, the delayed transaction is complete. If the second request from the initiator does not match the first
request exactly, then the bridge issues another retry to the initiator.
When bit 2 of the diagnostic control register (offset 5Ch, see Section 5.14) is 0, the PCI2250 is configured for
immediate retry mode. In immediate retry mode, the bridge issues a retry immediately, instead of after 16 clocks, on
delayed transactions.
The PCI2250 supports one delayed transaction in each direction at any given time.
3.14 Multifunction Pins
The PCI2250 has two multifunction pins that can be configured as LOCK, CLKRUN or compact-PCI hot-swap ENUM
and SWITCH. The configuration of P_MFUNC and S_MFUNC is controlled by MS0 and MS1 and is shown in
Table 3–3. The PCI2250 has two modes of operation: Intel-compatible mode and TI mode. In the Intel mode, the
PCI2250 is pin compatible with the Intel 21152 bridge.
Table 3–3. Multifunction Pin Definitions Based on Mode Select Pins
MS1
P_MFUNC
HS_ENUM
P_CLKRUN
P_LOCK
S_MFUNC
HS_SWITCH
S_CLKRUN
S_LOCK
MODE
TI hot-swap
TI clock run
Intel
MS0
0
0
1
0
1
BPCC
3.14.1 Compact-PCI Hot-Swap Support
The PCI2250 is hot-swap friendly silicon that supports all the CPCI hot-swap capable features, contains support for
software control, and integrates circuitry required by the CPCI Hot-Swap Specification. To be hot-swap capable, the
PCI2250 supports the following:
•
•
•
•
•
•
•
•
Compliance with PCI Local Bus Specification
Tolerance of V from early power
CC
Asynchronous reset
Tolerance of precharge voltage
I/O buffers must meet modified V/I requirements
Limited I/O pin voltage at precharge voltage
Hot-swap control and status programming via extended PCI capabilities linked list
Hot-swap terminals: HS_ENUM, HS_SWITCH, and HS_LED.
CPCI hot-swap defines a process for installing and removing PCI boards without adversely affecting a running
system. The PCI2250 provides this functionality such that it can be implemented on a board that can be removed
and inserted in a hot-swap system.
The PCI2250 provides three terminals to support hot-swap when configured to be in hot-swap mode: HS_ENUM
(output), HS_SWITCH (input), and HS_LED (output). The HS_ENUM output indicates to the system that an insertion
event occurred or that a removal event is about to occur. The HS_SWITCH input indicates the state of a board ejector
handle, and the HS_LED output lights a blue LED to signal insertion and removal ready status.
3–9
3.14.2 PCI Clock Run Feature
The PCI2250 supports the PCI clock run protocol when in clock run mode, as defined in the PCI Mobile Design Guide.
When the system’s central resource signals to the system that it wants to stop the PCI clock (P_CLK) by driving the
primary clock run (P_CLKRUN) signal high, the bridge either signals that it is OK to stop the PCI clock by leaving
P_CLKRUN deasserted (high) or signals to the system to keep the clock running by driving P_CLKRUN low.
The PCI2250 clock run control register provides a clock run enable bit for the primary bus and a separate clock run
enable bit for the secondary bus. The bridge’s P_CLKRUN and secondary clock run (S_CLKRUN) features are
enabled by setting bits 3 and 1, respectively, in the clock run control register (offset 5Bh, see Section 5.13). Bit 2 of
the clock run control register allows software to enable the bridge’s keep clock running mode to prevent the system
from stopping the primary PCI clock. There are two conditions for restarting the secondary clock: a downstream
transaction restarts the secondary clock or S_CLKRUN is asserted.
Two clock run modes are supported on the secondary bus. The bridge can be configured to stop the secondary PCI
clock only in response to a request from the primary bus to stop the clock, or it can be configured to stop the secondary
clock whenever the secondary bus is idle and there are no transaction requests from the primary bus, regardless of
the primary clock (see Section 5.13, Clock Run Control Register).
3.15 PCI Power Management
The PCI Power Management Interface Specification establishes the infrastructure required to let the operating
systemcontrolthepowerofPCIfunctions. ThisisdonebydefiningastandardPCIinterfaceandoperationstomanage
the power of PCI functions on the bus. The PCI bus and the PCI functions can be assigned one of four software visible
power management states, which result in varying levels of power savings.
The four power management states of PCI functions are D0—fully on state, D1 and D2—intermediate states, and
D3—off state. Similarly, bus power states are B0–B3. The bus power states B0–B3 are derived from the device power
state of the originating device. The power state of the secondary bus is derived from the power state of the PCI2250.
For the operating system to manage the device power states on the PCI bus, the PCI function supports four power
management operations:
•
•
•
•
Capabilities reporting
Power status reporting
Setting the power state
System wake–up
The operating system identifies the capabilities of the PCI function by traversing the new capabilities list. The
presence of the new capabilities list is indicated by a bit in the status register (offset 06h, see Section 4.4) which
provides access to the capabilities list.
3.15.1 Behavior in Low Power States
The PCI2250 supports D0, D1, D2, and D3
power states when in TI mode. The PCI2250 only supports D0 and
hot
D3 power states when in Intel mode. The PCI2250 is fully functional only in the D0 state. In the lower power states,
hot
the bridge does not accept any I/O or memory transactions. These transactions are aborted by the master. The bridge
accepts type 0 configuration cycles in all power states. The bridge also accepts type 1 configuration cycles but does
not pass these cycles to the secondary bus in any of the low power states. Type 1 configuration writes are discarded
and reads return all 1s. All error reporting is done in the low power states. When in D2 and D3 states, the bridge
hot
turns off all secondary clocks for further power savings when in TI mode or if BPCC is pulled high in the Intel mode.
When going from D3
to D0, an internal reset is generated. This reset initializes all PCI configuration registers to
hot
their default values. All TI extension registers (40h–FFh) are not reset. The power management registers (offset E0h)
are also not reset.
3–10
4 Bridge Configuration Header
The PCI2250 bridge is a single-function PCI device. The configuration header is in compliance with the PCI-to-PCI
Bridge Architecture Specification. Table 4–1 shows the PCI configuration header, which includes the predefined
portion of the bridge’s configuration space. The PCI configuration offset is shown in the right column under the
OFFSET heading.
Table 4–1. Bridge Configuration Header
REGISTER NAME
OFFSET
00h
Device ID
Status
Vendor ID
Command
04h
Class code
Header type
Revision ID
08h
BIST
Primary latency timer
Cache line size
0Ch
10h
Base address register 0
Base address register 1
14h
Secondary bus latency timer
Subordinate bus number
Secondary bus number
I/O limit
Primary bus number
I/O base
18h
Secondary status
1Ch
20h
Memory limit
Memory base
Prefetchable memory limit
Prefetchable memory base
24h
Prefetchable base upper 32 bits
Prefetchable limit upper 32 bits
28h
2Ch
30h
I/O limit upper 16 bits
I/O base upper 16 bits
Reserved
Expansion ROM base address
Interrupt pin
Extended diagnostic
Extension window base 0
Capability pointer
34h
38h
Bridge control
Arbiter control
Interrupt line
Chip control
3Ch
40h
44h
Extension window limit 0
Extension window base 1
Extension window limit 1
48h
4Ch
50h
Primary decode control
Clock run control
Secondary decode control
Extension window map
Buffer control
Extension window enable
Port decode enable
54h
Port decode map
58h
Diagnostic status
Diagnostic control
Reserved
P_SERR event disable
Secondary clock control
5Ch
60h
Arbiter timeout status
Arbiter mask control
Reserved
64h
Reserved
P_SERR status
68h
Reserved
PM next item pointer
Power management control/status
HS next item pointer HS capability ID
Reserved
6Ch–D8h
DCh
E0h
E4h
E8h–FFh
Power management capabilities
PM capability ID
Data
PMCSR bridge support
Hot-swap control status
Reserved
4–1
A bit description table is typically included that indicates bit field names, a detailed field description, and field access
tags. Table 4–2 describes the field access tags.
Table 4–2. Bit Field Access Tag Descriptions
ACCESS
TAG
NAME
MEANING
R
Read
Write
Set
Field may be read by software.
W
S
Field may be written by software to any value.
Field may be set by a write of 1. Writes of 0 have no effect.
Field may be cleared by a write of one. Writes of 0 have no effect.
C
Clear
U
Update Field may be autonomously updated by PCI2040.
4.1 Vendor ID Register
This 16-bit value is allocated by the PCI Special Interest Group (SIG) and identifies TI as the manufacturer of this
device. The vendor ID assigned to TI is 104Ch.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Vendor ID
R
0
R
0
R
0
R
1
R
0
R
0
R
0
R
0
R
0
R
1
R
0
R
0
R
1
R
1
R
0
R
0
Register:
Type:
Offset:
Default:
Vendor ID
Read-only
00h
104Ch
4.2 Device ID Register
This 16-bit value is allocated by the vendor and identifies the PCI device. The device ID for the PCI2250 is AC23h.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Device ID
R
1
R
0
R
1
R
0
R
1
R
1
R
0
R
0
R
0
R
0
R
1
R
0
R
0
R
0
R
1
R
1
Register:
Type:
Offset:
Default:
Device ID
Read-only
02h
AC23h
4–2
4.3 Command Register
The command register provides control over the bridge interface to the primary PCI bus. VGA palette snooping is
enabled through this register, and all other bits adhere to the definitions in the PCI Local Bus Specification. Table 4–3
describes the bit functions in the command register.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Command
R
0
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
R
0
R/W
0
R/W
0
R
0
R
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Command
Read-only, read/write (see individual bit descriptions)
Offset:
Default:
04h
0000h
Table 4–3. Command Register
BIT
TYPE
FUNCTION
15–10
R
Reserved. Bits 15–10 return 0s when read.
Fast back-to-back enable. The bridge does not generate fast back-to-back transactions on the primary PCI bus. Bit 9 is
read/write, but does not affect the bridge when set. This bit defaults to 0.
9
8
7
6
R/W
System error (SERR) enable. Bit 8 controls the enable for the SERR driver on the primary interface.
0 = Disable SERR driver on primary interface (default)
R/W
R
1 = Enable the SERR driver on primary interface
Wait cycle control. Bit 7 controls address/data stepping by the bridge on both interfaces. The bridge does not support
address/data stepping and this bit is hardwired to 0.
Parity error response enable. Bit 6 controls the bridge response to parity errors.
0 = Parity error response disabled (default)
R/W
1 = Parity error response enabled
VGA palette snoop enable. When set, the bridge passes I/O writes on the primary PCI bus with addresses 3C6h, 3C8h,
and 3C9h inclusive of ISA aliases (i.e., only bits AD9–AD0 are included in the decode).
5
4
3
R/W
R
Memory write and invalidate enable. In a PCI-to-PCI bridge, bit 4 must be read-only and return 0 when read.
Special cycle enable. A PCI-to-PCI bridge cannot respond as a target to special cycle transactions, so bit 3 is defined as
read-only and must return 0 when read.
R
Bus master enable. Bit 2 controls the ability of the bridge to initiate a cycle on the primary PCI bus. When bit 2 is 0, the bridge
does not respond to any memory or I/O transactions on the secondary interface since they cannot be forwarded to the
primary PCI bus.
2
R/W
0 = Bus master capability disabled (default)
1 = Bus master capability enabled
Memory space enable. Bit 1 controls the bridge response to memory accesses for both prefetchable and nonprefetchable
memory spaces on the primary PCI bus. Only when bit 1 is set will the bridge forward memory accesses to the secondary
bus from a primary bus initiator.
1
0
R/W
R/W
0 = Memory space disabled (default)
1 = Memory space enabled
I/O space enable. Bit 0 controls the bridge response to I/O accesses on the primary interface. Only when bit 0 is set will
the bridge forward I/O accesses to the secondary bus from a primary bus initiator.
0 = I/O space disabled (default)
1 = I/O space enabled
4–3
4.4 Status Register
The status register provides device information to the host system. This register is read-only. Bits in this register are
cleared by writing a 1 to the respective bit; writing a 0 to a bit location has no effect. Table 4–4 describes the status
register.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Status
R/C/
U
R/C/
U
R/C/
U
R/C/
U
R/C/
U
R/C/
U
Type
R
0
R
1
R
0
R
0
R
0
R
1
R
0
R
0
R
0
R
0
Default
0
0
0
0
0
0
Register:
Type:
Status
Read-only, Read/Clear/Update
Offset:
Default:
06h
0210h
Table 4–4. Status Register
BIT
TYPE
FUNCTION
15
R/C/U Detected parity error. Bit 15 is set when a parity error is detected.
Signaled system error (SERR). Bit 14 is set if SERR is enabled in the command register (offset 04h, see Section 4.3) and
the bridge signals a system error (SERR). See Section 3.9, System Error Handling.
0 = No SERR signaled (default)
14
13
12
R/C/U
R/C/U
R/C/U
1 = Signals SERR
Received master abort. Bit 13 is set when a cycle initiated by the bridge on the primary bus has been terminated by a master
abort.
0 = No master abort received (default)
1 = Master abort received
Received target abort. Bit 12 is set when a cycle initiated by the bridge on the primary bus has been terminated by a target
abort.
0 = No target abort received (default)
1 = Target abort received
Signaled target abort. Bit 11 is set by the bridge when it terminates a transaction on the primary bus with a target abort.
0 = No target abort signaled by the bridge (default)
11
R/C/U
R
1 = Target abort signaled by the bridge
DEVSEL timing. These read-only bits encode the timing of P_DEVSEL and are hardwired 01b, indicating that the bridge
asserts this signal at a medium speed.
01 = Hardwired (default)
10–9
Data parity error detected. Bit 8 is encoded as:
0 = The conditions for setting this bit have not been met. No parity error detected. (default)
1 = A data parity error occurred and the following conditions were met:
a. P_PERR was asserted by any PCI device including the bridge.
8
7
R/C/U
R
b. The bridge was the bus master during the data parity error.
c. Bit 6 (parity error response enable) is set in the command register (offset 04h, see Section 4.3).
Fast back-to-back capable. The bridge does not support fast back-to-back transactions as a target; therefore, bit 7 is
hardwired to 0.
User-definable feature (UDF) support. The PCI2250 does not support the user-definable features; therefore, bit 6 is
hardwired to 0.
6
5
R
R
R
R
66-MHz capable. The PCI2250 operates at a maximum P_CLK frequency of 33 MHz; therefore, bit 5 is hardwired to 0.
Capabilities list. Bit 4 is read-only and is hardwired to 1, indicating that capabilities additional to standard PCI are
implemented. The linked list of PCI power management capabilities is implemented by this function.
4
3–0
Reserved. Bits 3–0 return 0s when read.
4–4
4.5 Revision ID Register
The revision ID register indicates the silicon revision of the PCI2250.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Revision ID
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
1
Register:
Type:
Offset:
Default:
Revision ID
Read-only
08h
01h (reflects the current revision of the silicon)
4.6 Class Code Register
This register categorizes the PCI2250 as a PCI-to-PCI bridge device (0604h) with a 01h or 00h programming
interface. Bit 0 is read-only but its value is aliased with bit 0 of the primary decode control register (offset 57h, see
Section 5.9). Bit 0 of the primary decode control register defaults to 1b which means the primary interface is set for
subtractive decode. If software writes a 0 to bit 0 of the primary decode control register, then this value is aliased to
bit 0 of the class code register and the bridge will positively decode the primary interface.
Bit
23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
Name
Class code
Base class
Sub class
Programming interface
Type
R
0
R
0
R
0
R
0
R
0
R
1
R
1
R
0
R
0
R
0
R
0
R
0
R
0
R
1
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
1
Default
Register:
Type:
Offset:
Default:
Class code
Read-only
09h
060401h
4.7 Cache Line Size Register
The cache line size register is programmed by host software to indicate the system cache line size needed by the
bridge on memory read line and memory read multiple transactions.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Cache line size
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Cache line size
Read/write
0Ch
00h
4–5
4.8 Primary Latency Timer Register
The latency timer register specifies the latency timer for the bridge in units of PCI clock cycles. When the bridge is
aprimaryPCIbusinitiatorandassertsP_FRAME, thelatencytimerbeginscountingfrom0. Ifthelatencytimerexpires
before the bridge transaction has terminated, then the bridge terminates the transaction when its P_GNT is
deasserted.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Latency timer
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Latency timer
Read/write
0Dh
00h
4.9 Header Type Register
The header type register is read-only and returns 01h when read, indicating that the PCI2250 configuration space
adheres to the PCI-to-PCI bridge configuration. Only the layout for bytes 10h–3Fh of configuration space is
considered.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Header type
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
1
Register:
Type:
Offset:
Default:
Header type
Read-only
0Eh
01h
4.10 BIST Register
The PCI2250 does not support built-in self test (BIST). The BIST register is read-only and returns the value 00h when
read.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
BIST
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
BIST
Read-only
0Fh
00h
4–6
4.11 Base Address Register 0
The bridge requires no additional resources. Base address register 0 is read-only and returns 0s when read.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Base address register 0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
9
R
0
8
R
0
7
R
0
6
R
0
5
R
0
4
R
0
3
R
0
2
R
0
1
R
0
0
15
14
13
12
11
10
Name
Type
Default
Base address register 0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Base address register 0
Read-only
Offset:
Default:
10h
0000 0000h
4.12 Base Address Register 1
The bridge requires no additional resources. Base address register 1 is read-only and returns 0s when read.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Base address register 1
R
0
R
0
R
0
R
0
R
0
R
0
R
0
9
R
0
8
R
0
7
R
0
6
R
0
5
R
0
4
R
0
3
R
0
2
R
0
1
R
0
0
15
14
13
12
11
10
Name
Type
Default
Base address register 1
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Base address register 1
Read-only
Offset:
Default:
14h
0000 0000h
4.13 Primary Bus Number Register
The primary bus number register indicates the primary bus number to which the bridge is connected. The bridge uses
this register, in conjunction with the secondary bus number and subordinate bus number registers, to determine when
to forward PCI configuration cycles to the secondary buses.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Primary bus number
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Primary bus number
Read/write
18h
00h
4–7
4.14 Secondary Bus Number Register
The secondary bus number register indicates the secondary bus number to which the bridge is connected. The
PCI2250 uses this register, in conjunction with the primary bus number and subordinate bus number registers, to
determine when to forward PCI configuration cycles to the secondary buses. Configuration cycles directed to the
secondary bus are converted to type 0 configuration cycles.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Secondary bus number
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Secondary bus number
Read/write
19h
00h
4.15 Subordinate Bus Number Register
The subordinate bus number register indicates the bus number of the highest numbered bus beyond the primary bus
existingbehindthebridge. ThePCI2250usesthisregister, inconjunctionwiththeprimarybusnumberandsecondary
bus number registers, to determine when to forward PCI configuration cycles to the subordinate buses. Configuration
cycles directed to a subordinate bus (not the secondary bus) remain type 1 cycles as the cycle crosses the bridge.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Subordinate bus number
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Subordinate bus number
Read/write
1Ah
00h
4.16 Secondary Bus Latency Timer Register
ThesecondarybuslatencytimerspecifiesthelatencytimerforthebridgeinunitsofPCIclockcycles. Whenthebridge
is a secondary PCI bus initiator and asserts S_FRAME, the latency timer begins counting from 0. If the latency timer
expires before the bridge transaction has terminated, then the bridge terminates the transaction when its S_GNT is
deasserted. The PCI-to-PCI bridge S_GNT is an internal signal and is removed when another secondary bus master
arbitrates for the bus.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Secondary bus latency timer
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Secondary bus latency timer
Read/write
1Bh
00h
4–8
4.17 I/O Base Register
The I/O base register is used in decoding I/O addresses to pass through the bridge. The bridge supports 32-bit I/O
addressing; thus, bits 3–0 are read-only and default to 0001b. The upper four bits are writable and correspond to
address bits AD15–AD12. The lower 12 address bits of the I/O base address are considered 0. Thus, the bottom of
the defined I/O address range is aligned on a 4K-byte boundary. The upper 16 address bits of the 32-bit I/O base
address corresponds to the contents of the I/O base upper 16 bits register (offset 30h, see Section 4.26).
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
I/O base
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
R
0
R
1
Register:
Type:
I/O base
Read-only, read/write
Offset:
Default:
1Ch
01h
4.18 I/O Limit Register
The I/O limit register is used in decoding I/O addresses to pass through the bridge. The bridge supports 32-bit I/O
addressing; thus, bits 3–0 are read-only and default to 0001b. The upper four bits are writable and correspond to
address bits AD15–AD12. The lower 12 address bits of the I/O limit address are considered FFFh. Thus, the top of
the defined I/O address range is aligned on a 4K-byte boundary. The upper 16 address bits of the 32-bit I/O limit
address corresponds to the contents of the I/O limit upper 16 bits register (offset 32h, see Section 4.27).
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
I/O limit
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
R
0
R
1
Register:
Type:
I/O limit
Read-only, read/write
Offset:
Default:
1Dh
01h
4–9
4.19 Secondary Status Register
The secondary status register is similar in function to the status register (offset 06h, see Section 4.4); however, its
bits reflect status conditions of the secondary interface. Bits in this register are cleared by writing a 1 to the respective
bit.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Secondary status
R/C/
U
R/C/
U
R/C/
U
R/C/
U
R/C/
U
R/C/
R
Type
R
0
R
1
R
0
R
0
R
0
R
0
R
0
R
0
R
0
U
Default
0
0
0
0
0
0
0
Register:
Type:
Secondary status
Read-only, Read/Clear/Update
Offset:
Default:
1Eh
0200h
Table 4–5. Secondary Status Register
BIT
TYPE
FUNCTION
Detected parity error. Bit 15 is set when a parity error is detected on the secondary interface.
0 = No parity error detected on the secondary bus (default)
15
R/C/U
1 = Parity error detected on the secondary bus
Received system error. Bit 14 is set when the secondary interface detects S_SERR asserted. Note that the bridge never
asserts S_SERR.
14
13
12
R/C/U
0 = No S_SERR detected on the secondary bus (default)
1 = S_SERR detected on the secondary bus
Received master abort. Bit 13 is set when a cycle initiated by the bridge on the secondary bus has been terminated by a
master abort.
R/C/U
R/C/U
0 = No master abort received (default)
1 = Bridge master aborted the cycle
Receivedtargetabort. Bit12issetwhenacycleinitiatedbythebridgeonthesecondarybushasbeenterminatedbyatarget
abort.
0 = No target abort received (default)
1 = Bridge received a target abort
Signaled target abort. Bit 11 is set by the bridge when it terminates a transaction on the secondary bus with a target abort.
0 = No target abort signaled (default)
11
R/C/U
R
1 = Bridge signaled a target abort
DEVSEL timing. Bits 10 and 9 encode the timing of S_DEVSEL and are hardwired to 01b, indicating that the bridge asserts
this signal at a medium speed.
10–9
Data parity error detected.
0 = The conditions for setting this bit have not been met
1 = A data parity error occurred and the following conditions were met:
a. S_PERR was asserted by any PCI device including the bridge.
b. The bridge was the bus master during the data parity error.
c. The parity error response bit (bit 0) is set in the bridge control register (offset 3Eh, se Section 4.32).
8
R/C/U
7
6
R
R
R
R
Fast back-to-back capable. Bit 7 is hardwired to 0.
User-definable feature (UDF) support. Bit 6 is hardwired to 0.
66-MHz capable. Bit 5 is hardwired to 0.
5
4–0
Reserved. Bits 4–0 return 0s when read.
4–10
4.20 Memory Base Register
The memory base register defines the base address of a memory-mapped I/O address range used by the bridge to
determine when to forward memory transactions from one interface to the other. The upper 12 bits of this register
are read/write and correspond to the address bits AD31–AD20. The lower 20 address bits are considered 0s; thus,
the address range is aligned to a 1M-byte boundary. The bottom four bits are read-only and return 0s when read.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Memory base
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
R
0
R
0
Register:
Type:
Memory base
Read-only, read/write
Offset:
Default:
20h
0000h
4.21 Memory Limit Register
The memory limit register defines the upper-limit address of a memory-mapped I/O address range used to determine
when to forward memory transactions from one interface to the other. The upper 12 bits of this register are read/write
and correspond to the address bits AD31–AD20. The lower 20 address bits are considered 1s; thus, the address
range is aligned to a 1M-byte boundary. The bottom four bits are read-only and return 0s when read.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Memory limit
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
R
0
R
0
Register:
Type:
Memory limit
Read-only, read/write
Offset:
Default:
22h
0000h
4.22 Prefetchable Memory Base Register
The prefetchable memory base register defines the base address of a prefetchable memory address range used by
the bridge to determine when to forward memory transactions from one interface to the other. The upper 12 bits of
this register are read/write and correspond to the address bits AD31–AD20. The lower 20 address bits are considered
0; thus, the address range is aligned to a 1M-byte boundary. The bottom four bits are read-only and return 0s
when read.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Prefetchable memory base
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
R
0
R
0
Register:
Type:
Prefetchable memory base
Read-only, read/write
Offset:
Default:
24h
0000h
4–11
4.23 Prefetchable Memory Limit Register
The prefetchable memory limit register defines the upper-limit address of a prefetchable memory address range used
to determine when to forward memory transactions from one interface to the other. The upper 12 bits of this register
are read/write and correspond to the address bits AD31–AD20. The lower 20 address bits are considered 1s; thus,
the address range is aligned to a 1M-byte boundary. The bottom four bits are read-only and return 0s when read.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Prefetchable memory limit
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
R
0
R
0
Register:
Type:
Prefetchable memory limit
Read-only, read/write
Offset:
Default:
26h
0000h
4.24 Prefetchable Base Upper 32 Bits Register
The PCI2250 does not support 64-bit addressing; thus, the prefetchable base upper 32-bit register is read-only and
returns 0s when read.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Prefetchable base upper 32 bits
R
0
R
0
R
0
R
0
R
0
R
0
R
0
9
R
0
8
R
0
7
R
0
6
R
0
5
R
0
4
R
0
3
R
0
2
R
0
1
R
0
0
15
14
13
12
11
10
Name
Type
Default
Prefetchable base upper 32 bits
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
Prefetchable base upper 32 bits
Read-only
28h
0000 0000h
4.25 Prefetchable Limit Upper 32 Bits Register
The PCI2250 does not support 64-bit addressing; thus the prefetchable limit upper 32-bit register is read-only and
returns 0s when read.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Prefetchable limit upper 32 bits
R
0
R
0
R
0
R
0
R
0
R
0
R
0
9
R
0
8
R
0
7
R
0
6
R
0
5
R
0
4
R
0
3
R
0
2
R
0
1
R
0
0
15
14
13
12
11
10
Name
Type
Default
Prefetchable limit upper 32 bits
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
Prefetchable limit upper 32 bits
Read-only
2Ch
0000 0000h
4–12
4.26 I/O Base Upper 16 Bits Register
The I/O base upper 16 bits register specifies the upper 16 bits corresponding to AD31–AD16 of the 32-bit address
that specifies the base of the I/O range to forward from the primary PCI bus to the secondary PCI bus.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
I/O base upper 16 bits
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
I/O base upper 16 bits
Read/Write
30h
0000h
4.27 I/O Limit Upper 16 Bits Register
The I/O limit upper 16-bits register specifies the upper 16 bits corresponding to AD31–AD16 of the 32-bit address
that specifies the upper limit of the I/O range to forward from the primary PCI bus to the secondary PCI bus.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
I/O limit upper 16 bits
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
I/O limit upper 16 bits
Read/Write
32h
0000h
4.28 Capability Pointer Register
ThecapabilitypointerregisterprovidesthepointertothePCIconfigurationheaderwherethePCIpowermanagement
register block resides. The capability pointer provides access to the first item in the linked list of capabilities. The
capability pointer register is read-only and returns DCh when read, indicating the power management registers are
located at PCI header offset DCh.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Capability pointer register
R
1
R
1
R
0
R
1
R
1
R
1
R
0
R
0
Register:
Type:
Offset:
Default:
capability pointer
Read-only
34h
DCh
4–13
4.29 Expansion ROM Base Address Register
The PCI2250 does not implement the expansion ROM remapping feature. The expansion ROM base address
register returns all 0s when read.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Expansion ROM base address
R
0
R
0
R
0
R
0
R
0
R
0
R
0
9
R
0
8
R
0
7
R
0
6
R
0
5
R
0
4
R
0
3
R
0
2
R
0
1
R
0
0
15
14
13
12
11
10
Name
Type
Default
Expansion ROM base address
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
Expansion ROM base address
Read-only
38h
0000 0000h
4.30 Interrupt Line Register
The interrupt line register is read/write and is used to communicate interrupt line routing information. Since the bridge
does not implement an interrupt signal terminal, this register defaults to FFh.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Interrupt line
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
R/W
1
Register:
Type:
Offset:
Default:
Interrupt line
Read/write
3Ch
FFh
4.31 Interrupt Pin Register
The bridge default state does not implement any interrupt terminals. Reads from bits 7–0 of this register return 0s.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Interrupt pin
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
Interrupt pin
Read-only
3Dh
00h
4–14
4.32 Bridge Control Register
The bridge control register provides many of the same controls for the secondary interface that are provided by the
command register (offset 04h, see Section 4.3) for the primary interface. Some bits affect the operation of both
interfaces.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Bridge control
R
0
R
0
R
0
R
0
R/W
0
RCU
0
R/W
0
R/W
0
R
0
R/W
0
R/W
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Bridge control
Read-only, read/write (see individual bit descriptions)
Offset:
Default:
3Eh
0000h
Table 4–6. Bridge Control Register
BIT
TYPE
FUNCTION
15–12
R
Reserved. Bits 15–12 return 0s when read.
Discard timer SERR enable.
11
10
R/W
0 = SERR signaling disabled for primary discard timeouts (default)
1 = SERR signaling enabled for primary discard timeouts
Discard timer status. Once set, this bit must be cleared by writing 1 to this bit.
0 = No discard timer error (default)
RCU
R/W
1 = Discard timer error. Either primary or secondary discard timer expired and a delayed transaction was discarded from
the queue in the bridge.
Secondary discard timer. Selects the number of PCI clocks that the bridge will wait for a master on the secondary interface
to repeat a delayed transaction request.
9
15
0 = Secondary discard timer counts 2 PCI clock cycles (default)
10
1 = Secondary discard timer counts 2 PCI clock cycles
Primary discard timer. Selects the number of PCI clocks that the bridge will wait for a master on the primary interface to
repeat a delayed transaction request.
8
7
6
R/W
R
15
0 = The primary discard timer counts 2 PCI clock cycles (default)
10
1 = The primary discard timer counts 2 PCI clock cycles
Fast back-to-back capable. The bridge never generates fast back-to-back transactions to different secondary devices. Bit
7 returns 0 when read.
Secondary bus reset. When bit 6 is set, the secondary reset signal (S_RST) is asserted. S_RST is deasserted by resetting
this bit. Bit 6 is encoded as:
R/W
0 = Do not force the assertion of S_RST (default).
1 = Force the assertion of S_RST.
Master abort mode. Bit 5 controls how the bridge responds to a master abort that occurs on either interface when the bridge
is the master. If this bit is set and the posted write transaction has completed on the requesting interface, and SERR enable
(bit 8) of the command register (offset 04h, see Section 4.3) is 1, then P_SERR is asserted when a master abort occurs.
If the transaction has not completed, then a target abort is signaled. If the bit is cleared, then all 1s are returned on reads
and write data is accepted and discarded when a transaction that crosses the bridge is terminated with master abort. The
default state of bit 5 after a reset is 0.
5
R/W
0 = Do not report master aborts (return FFFF FFFFh on reads and discard data on writes) (default).
1 = Report master aborts by signaling target abort if possible, or if SERR is enabled via bit 1 of this register, by
asserting SERR.
4
3
R
Reserved. Bit 4 returns 0 when read.
VGA enable. When bit 3 is set, the bridge positively decodes and forwards VGA-compatible memory addresses in the video
frame buffer range 000A 0000h–000B FFFFh, I/O addresses in the range 03B0h–03BBh, and 03C0–03DFh from the
primary to the secondary interface, independent of the I/O and memory address ranges. When this bit is set, the bridge
blocks forwarding of these addresses from the secondary to the primary. Reset clears this bit. Bit 3 is encoded as:
0 = Do not forward VGA-compatible memory and I/O addresses from the primary to the secondary interface (default).
1 = Forward VGA-compatible memory and I/O addresses from the primary to the secondary, independent of the I/O
and memory address ranges and independent of the ISA enable bit.
R/W
4–15
Table 4–6. Bridge Control Register (Continued0)
BIT
TYPE
FUNCTION
ISA enable. When bit 2 is set, the bridge blocks the forwarding of ISA I/O transactions from the primary to the secondary,
addressingthelast768bytesineach1K-byteblock. Thisappliesonlytotheaddresses(definedbytheI/Owindowregisters)
that are located in the first 64K bytes of PCI I/O address space. From the secondary to the primary, I/O transactions are
forwardediftheyaddressthelast768bytesineach1K-byteblockintheaddressrangespecifiedintheI/Owindowregisters.
Bit 2 is encoded as:
2
R/W
0 = Forward all I/O addresses in the address range defined by the I/O base and I/O limit registers (default).
1 = Block forwarding of ISA I/O addresses in the address range defined by the I/O base and I/O limit registers when
these I/O addresses are in the first 64K bytes of PCI I/O address space and address the top 768 bytes of each
1K-byte block.
SERR enable. Bit 1 controls the forwarding of secondary interface SERR assertions to the primary interface. Only when
this bit is set will the bridge forward S_SERR to the primary bus signal P_SERR. For the primary interface to assert SERR,
bit 8 of the command register (offset 04h, see Section 4.3) must be set.
0 = SERR disabled (default)
1
0
R/W
R/W
1 = SERR enabled
Parity error response enable. Bit 0 controls the bridge response to parity errors on the secondary interface. When this bit
is set, the bridge asserts S_PERR to report parity errors on the secondary interface.
0 = Ignore address and parity errors on the secondary interface (default).
1 = Enable parity error reporting and detection on the secondary interface.
4–16
5 Extension Registers
The TI extension registers are those registers that lie outside the standard PCI-to-PCI bridge device configuration
space (i.e., registers 40h–FFh in PCI configuration space in the PCI2250). These registers can be accessed through
configuration reads and writes. The TI extension registers add flexibility and performance benefits to the standard
PCI-to-PCI bridge. The TI extension registers are not reset on the transition from D3 to D0.
5.1 Chip Control Register
The chip control register is read/write and has a default value of 00h. This register is used to control the functionality
of certain PCI transactions. See Table 5–1 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Chip control
R
0
R
0
R
0
R/W
0
R
0
R
0
R/W
0
R
0
Register:
Type:
Chip control
Read/Write, Read–only
Offset:
Default:
40h
00h
Table 5–1. Chip Control Register
BIT
TYPE
FUNCTION
7–5
R
Reserved. Bits 7–5 return 0s when read.
Memory read prefetch. When cleared, bit 4 enables the memory read prefetch.
0 = Upstream memory reads are enabled (default)
4
R/W
1 = Upstream memory reads are disabled
3–2
1
R
R/W
R
Reserved. Bits 3 and 2 return 0s when read.
Reserved
0
Reserved. Bit 0 returns 0 when read.
5–1
5.2 Extended Diagnostic Register
The extended diagnostic register is read or write and has a default value of 00h. Bit 0 of this register is used to reset
both the PCI2250 and the secondary bus.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Extended diagnostic
R
0
R
0
R
0
R
0
R
0
R
0
R
0
W
0
Register:
Type:
Extended diagnostic
Read-only, Write-only
Offset:
Default:
41h
00h
Table 5–2. Extended Diagnostic Register
BIT
TYPE
FUNCTION
7–1
R
Reserved. Bits 7–1 return 0s when read.
Writing a 1 to this bit causes the PCI2250 to set bit 6 of the bridge control register (offset 3Eh, see Section 4.32) and then
internally reset the PCI2250. Bit 6 of the bridge control register will not be reset by the internal reset. Bit 0 is self-clearing.
0
W
5–2
5.3 Arbiter Control Register
The arbiter control register is used for the bridge’s internal arbiter. The arbitration scheme used is a two-tier rotational
arbitration. The PCI2250 bridge is the only secondary bus initiator that defaults to the higher priority arbitration tier.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Arbiter control
R
0
R
0
R
0
R
0
R
0
R
0
R/W
1
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Arbiter control
Read-only, Read/Write
Offset:
Default:
42h
0200h
Table 5–3. Arbiter Control Register
BIT
TYPE
FUNCTION
15–10
R
Reserved. Bits 15–10 return 0s when read.
Bridge tier select. This bit determines in which tier the bridge is placed in the two-tier arbitration scheme.
9
8–4
3
R/W
R
0 = Lowest priority tier
1 = Highest priority tier (default)
Reserved. Bits 8–4 return 0s when read.
GNT3 tier select. This bit determines in which tier the S_GNT3 is placed in the arbitration scheme. This bit is encoded as:
R/W
0 = Lowest priority tier (default)
1 = Highest priority tier
GNT2 tier select. This bit determines in which tier the S_GNT2 is placed in the arbitration scheme. This bit is encoded as:
2
1
0
R/W
R/W
R/W
0 = Lowest priority tier (default)
1 = Highest priority tier
GNT1 tier select. This bit determines in which tier the S_GNT1 is placed in the arbitration scheme. This bit is encoded as:
0 = Lowest priority tier (default)
1 = Highest priority tier
GNT0 tier select. This bit determines in which tier the S_GNT0 is placed in the arbitration scheme. This bit is encoded as:
0 = Lowest priority tier (default)
1 = Highest priority tier
5–3
5.4 Extension Window Base 0, 1 Registers
Thebridgesupportstwoextensionwindowsthatdefineanaddressrangedecodedasdescribedinthewindowenable
registerandwindowmapregister. Theextensionwindowbaseregistersdefinethe32-bitbaseaddressofthewindow.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Extension window base 0, 1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Extension window base 0, 1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R
0
R
0
Register:
Type:
Offset:
Default:
Extension window base 0, 1
Read-only, Read/Write
44h, 4Ch
0000 0000h
5.5 Extension Window Limit 0, 1 Registers
The bridge supports two extension windows. Each window defines an address range that is decoded as described
in the window enable register and window map register. The extension window limit registers define the 32-bit limit
address of the window.
Bits 0 and 1 of this register determine whether the extension window is a prefetchable memory window, a
nonprefetchable window, or an I/O window. These bits are encoded as:
00 = Nonprefetchable memory
01 = Prefetchable memory
1x = I/O
Memory windows have a 4–Kbyte granularity and I/O windows have a doubleword (4-byte) granularity. When a
memory window is selected, bits 11–2 have no effect and are assumed to be 1s for the limit register and 0s for the
base register. This is consistent with the 4K-byte granularity of the memory windows.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
Type
Default
Bit
Extension window limit 0, 1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Extension window limit 0, 1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Extension window limit 0, 1
Read/Write
Offset:
Default:
48h, 50h
0000 0000h
5–4
5.6 Extension Window Enable Register
The decode of the extension windows is enabled through bits 0 and 1 of this register. See Table 5–4 for a complete
description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Extension window enable
R
0
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
Register:
Type:
Extension window enable
Read-only, Read/Write
Offset:
Default:
54h
00h
Table 5–4. Extension Window Enable Register
BIT
TYPE
FUNCTION
7–2
R
Reserved. Bits 7–2 return 0s when read.
Extension window 1 interface enable
1
0
R/W
0 = Disable window 1 (default)
1 = Enable window 1
Extension window 0 interface enable
0 = Disable window 0 (default)
1 = Enable window 0
R/W
5.7 Extension Window Map Register
The inclusion or exclusion of the extension windows on the primary interface is selected through bits 0 and 1 of this
register. The bit descriptions discuss the decode in reference to the primary interface. The secondary interface is the
negative decode of the primary interface. Regions excluded on the primary interface can be positively decoded on
the secondary interface if negative decoding is disabled on the secondary interface. See Table 5–5 for a complete
description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Extension window map
R
0
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
Register:
Type:
Extension window map
Read-only, Read/Write
Offset:
Default:
55h
00h
Table 5–5. Extension Window Map Register
BIT
TYPE
FUNCTION
7–2
R
Reserved. Bits 7–2 return 0s when read.
Extension window 1 interface include/exclude
1
0
R/W
0 = Extension window 1 included in primary interface decode (default)
1 = Extension window 1 excluded in primary interface decode
Extension window 0 interface include/exclude
R/W
0 = Extension window 0 included in primary interface decode (default)
1 = Extension window 0 excluded in primary interface decode
5–5
5.8 Secondary Decode Control Register
The secondary decode control register is used to enable/disable the secondary-bus negative decoding. Only through
this register can an extension window be defined for positive decoding or excluded from negative decoding from the
secondary bus to the primary bus. The window interface bits in the window control registers must be set for the
extension window definitions in this register to have meaning.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Secondary decode control
R
0
R
0
R
0
R
0
R
0
R/W
1
R/W
1
R/W
0
Register:
Type:
Secondary decode control
Read-only, Read/Write
Offset:
Default:
56h
06h
Table 5–6. Secondary Decode Control Register
BIT
TYPE
FUNCTION
7–3
R
Reserved. Bits 7–3 return 0s when read.
Secondary-bussubtractivedecodespeed. Thebridgedefaultstosubtractivedecodingafterslowdecodespeed(fourclocks
after FRAME is asserted). Bit 0 must be set to enable subtractive decoding. When bit 0 and this bit are set, subtractive
decoding is enabled at slow decode speed. This bit is encoded as:
2
1
R/W
0 = Selects normal subtractive decode speed.
1 = Selects subtractive decode in the slow decode time slot (default).
Secondary bus negative decode enable. The bridge defaults to negative decoding on the secondary PCI bus. All
transactions that do not fall into windows positively decoded from the primary to the secondary are passed through to the
primary bus. This bit is encoded as:
R/W
R/W
0 = Disable secondary-bus negative decoding.
1 = Enable secondary-bus negative decoding (default).
Secondary-bussubtractive decode enable. The bridge defaults to negative decoding on the secondary PCI bus. When bit 0
is set, the bridge uses subtractive decoding on the secondary bus. When the bridge is using negative decoding on the
secondary, all transactions not claimed by a slow device on the secondary bus are passed through the bridge to the primary
bus. This bit is encoded as:
0
0 = Disable secondary bus subtractive decoding (default).
1 = Enable secondary bus subtractive decoding.
5–6
5.9 Primary Decode Control Register
This register is used to enable and disable the primary bus subtractive decoding and to select the primary bus
subtractive decode speed. The bridge defaults to primary bus subtractive decoding enabled (bit 0 is set to 1b). Bit 0
of this register is aliased to bit 0 of the class code register (offset 09h, see Section 4.6) so that the class code register
reflects whether or not subtractive decoding is enabled on the primary interface. See Table 5–7 for a complete
description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Primary decode control
R
0
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
Register:
Type:
Primary decode control
Read-only, Read/Write
Offset:
Default:
57h
00h
Table 5–7. Primary Decode Control Register
BIT
TYPE
FUNCTION
7–2
R
Reserved. Bits 7–2 return 0s when read.
Primary-bus subtractive decode speed. The bridge defaults to subtractive decoding after slow decode speed (four clocks
after FRAME is asserted). Bit 0 must be set to enable subtractive decoding. When bit 0 and this bit are set, subtractive
decoding is enabled at slow decode speed. This bit is encoded as:
1
0
R/W
0 = Selects normal subtractive decode speed on primary bus (default)
1 = Selects subtractive decode in the slow decode time slot on the primary bus
Primary-bussubtractivedecodeenable. Thebridgedefaultstosubtractivedecodingdisabledfromtheprimarytosecondary
PCI bus. Each PCI bus may only have one subtractive decode device.
0 = Disable primary bus subtractive decoding
R/W
1 = Enable primary bus subtractive decoding (default)
5–7
5.10 Port Decode Enable Register
The port decode enable register is used to select which serial and parallel port addresses are positively decoded from
the bridge primary bus to the secondary bus. See Table 5–8 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Port decode enable
R
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Port decode enable
Read-only, Read/Write
Offset:
Default:
58h
00h
Table 5–8. Port Decode Enable Register
BIT
TYPE
FUNCTION
7
R
Reserved. Bit 7 returns 0 when read.
LPT3 enable. When bit 6 is set, the address ranges 278h–27Fh and 678h–67Bh are positively decoded and the cycles
passed to the secondary bus based on the setting of bit 6 of the port decode map register (offset 5Ah, see Section 5.12).
6
5
4
3
2
1
R/W
LPT2 enable. When bit 5 is set, the address ranges 378h–37Fh and 778h–77Bh are positively decoded and the cycles
passed to the secondary bus based on the setting of bit 5 of the port decode map register (offset 5Ah, see Section 5.12).
R/W
R/W
R/W
R/W
R/W
LPT1 enable. When bit 4 is set, the address ranges 3BCh–3BFh and 7BCh–7BFh are positively decoded and the cycles
passed to the secondary bus based on the setting of bit 4 of the port decode map register (offset 5Ah, see Section 5.12).
COM4 enable. When bit 3 is set, the address range 2E8h–2EFh is positively decoded and the cycles passed to the
secondary bus based on the setting of bit 3 of the port decode map register (offset 5Ah, see Section 5.12).
COM3 enable. When bit 2 is set, the address range 3E8h–3EFh is positively decoded and the cycles passed to the
secondary bus based on the setting of bit 2 of the port decode map register (offset 5Ah, see Section 5.12).
COM2 enable. When bit 1 is set, the address range 2F8h–2FFh is positively decoded and the cycles passed to the
secondary bus based on the setting of bit 1 of the port decode map register (offset 5Ah, see Section 5.12).
COM1 enable. When bit 0 is set, the address range 3F8h–3FFh is positively decoded and the cycles passed to the
secondary bus based on the setting of bit 0 of the port decode map register (offset 5Ah, see Section 5.12).
0
R/W
5–8
5.11 Buffer Control Register
The buffer control register allows software to enable/disable write posting and control memory read burst prefetching.
The buffer control register also enables/disables the posted memory write reconnect feature. See Table 5–9 for a
complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Buffer control
R
0
R
0
R
0
R/W
0
R
0
R/W
1
R/W
1
R/W
1
Register:
Type:
Buffer control
Read-only, Read/Write
Offset:
Default:
59h
07h
Table 5–9. Buffer Control Register
BIT
TYPE
FUNCTION
7–5
R
Reserved. Bits 7 through 5 return 0s when read.
Upstream MRM/MRL read burst enable. By default, the PCI2250 is set to memory read burst a single cache line. By setting
this bit to 1, the PCI2250 will memory read burst multiple cache lines or until the FIFO is full. To utilize this feature, bit 4 of
the chip control register (offset 40h, see Section 5.1) must be set to 0.
4
R/W
0 = Disabled (default)
1 = Enabled
3
2
R
Reserved. Bit 3 returns 0 when read.
Downstream memory read burst enable. The bridge defaults to downstream memory read bursting enabled. Bit 2 enables
downstream memory read bursting in prefetchable windows. This bit is encoded as:
R/W
0 = Disabled
1 = Enabled (default)
Secondary-to-primary write posting enable. Enables posting of write data to and from the primary interface. If bit 1 is not
set, the bridge must drain any data in its buffers before accepting data to or from the primary interface. Each data word must
then be accepted by the target before the bridge can accept the next word from the source master. The bridge must not
release the source master until the last word is accepted by the target. Operating with the write posting enabled enhances
system performance.
1
0
R/W
R/W
0 = Write posting disabled
1 = Write posting enabled (default)
Primary-to-secondary write posting enable. Enables posting of write data to and from the secondary interface. If bit 0 is not
set, then the bridge must drain any data in its buffers before accepting data to or from the secondary interface. Each data
word must then be accepted by the target before the bridge can accept the next word from the source master. The bridge
must not release the source master until the last word is accepted by the target. Operating with the write posting enabled
enhances system performance.
0 = Write posting disabled
1 = Write posting enabled (default)
5–9
5.12 Port Decode Map Register
The port decode map register is used to select whether the serial- and parallel-port address ranges positively
decoded from the primary bridge interface to the secondary interface are included or excluded from the primary
interface. For example, if bit 0 is set, then addresses in the range of 3F8h–3FFh are positively decoded on the primary
bus. If bit 0 is cleared and an I/O window is enabled that covers the range from 3F8h–3FFh, then these addresses
are not claimed by the bridge. See Table 5–10 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Port decode map
R/W R/W
R
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
0
0
Register:
Type:
Port decode map
Read-only, Read/Write
Offset:
Default:
5Ah
00h
Table 5–10. Port Decode Map Register
BIT
TYPE
FUNCTION
7
R
Reserved. Bit 7 returns 0 when read.
LPT3 include/exclude. Bit 6 is encoded as:
6
5
4
3
2
1
0
R/W
0 = 278h–27Fh and 678h–67Bh excluded from the primary bus (default)
1 = 278h–27Fh and 678h–67Bh positively decoded on the primary bus
LPT2 include/exclude. Bit 5 is encoded as:
R/W
R/W
R/W
R/W
R/W
R/W
0 = 378h–37Fh and 778h–77Bh excluded from the primary bus (default)
1 = 378h–37Fh and 778h–77Bh positively decoded on the primary bus
LPT1 include/exclude. Bit 4 is encoded as:
0 = 3BCh–3BFh and 7BCh–7BFh excluded from the primary bus (default)
1 = 3BCh–3BFh and 7BCh–7BFh positively decoded on the primary bus
COM4 include/exclude. Bit 3 is encoded as:
0 = 2E8h–2EFh excluded from the primary bus (default)
1 = 2E8h–2EFh positively decoded on the primary bus
COM3 include/exclude. Bit 2 is encoded as:
0 = 3E8h–3EFh excluded from the primary bus (default)
1 = 3E8h–3EFh positively decoded on the primary bus
COM2 include/exclude. Bit 1 is encoded as:
0 = 2F8h–2FFh excluded from the primary bus (default)
1 = 2F8h–2FFh positively decoded on the primary bus
COM1 include/exclude. Bit 0 is encoded as:
0 = 3F8h–3FFh excluded from the primary bus (default)
1 = 3F8h–3FFh positively decoded on the primary bus
5–10
5.13 Clock Run Control Register
The clock run control register controls the PCI clock-run mode enable/disable. It is also used to enable the
keep-clock-running feature. Bit 0 reflects the status of the secondary clock. There are two clock run modes supported
on the secondary bus. The bridge can be configured to stop the secondary PCI clock only in response to a request
from the primary bus to stop the clock or it can be configured to stop the secondary clock whenever the secondary
bus is idle and there are no transaction requests from the primary bus.
There are two conditions for restarting the secondary clock. A downstream transaction restarts the secondary clock,
or if the S_CLKRUN signal is asserted, the secondary clock is restarted. See Table 5–11 for a complete description
of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Clock run control
R/W R/W
R
0
R
0
R
0
R/W
0
R/W
0
R
0
0
0
Register:
Type:
Clock run control
Read-only, Read/Write
Offset:
Default:
5Bh
00h
Table 5–11. Clock Run Control Register
BIT
TYPE
FUNCTION
7–5
R
Reserved. Bits 7–5 return 0s when read.
Clock run mode. Bit 4 is encoded as:
0 = Stop the secondary clock only on request from the primary bus (default).
4
3
R/W
1 = Stop the secondary clock whenever the secondary bus is idle and there are no requests from the primary bus.
Primary clock run enable. Bit 3 must be enabled for the bridge to respond to requests by the central resource on the primary
bus to stop the clock.
R/W
0 = Disable clock run (default)
1 = Enable clock run
Primary keep clock. When bit 2 is set, it causes the bridge to request that the central resource keep the PCI clock running.
0 = Allow primary clock to stop if secondary clock stopped (default)
2
1
0
R/W
R/W
R
1 = Always keep primary clock running
Secondary clock run enable
0 = Disable clock run for secondary (default)
1 = Enable clock run for secondary
Secondary clock status bit. If the clock is stopped, this bit is 1. If the clock is running, this bit is 0.
0 = Secondary clock not stopped (default)
1 = Secondary clock stopped
5.14 Diagnostic Control Register
The diagnostic control register is used for bridge diagnostics. See Table 5–12 for a complete description of the
register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Diagnostic control
R/W
0
R/W
0
R/W
0
R/W
1
R/W
0
R/W
0
R
0
R
0
R/W
0
R/W
1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Offset:
Default:
Diagnostic control
Read/Write, Read-only
5Ch–5Dh
1040h
5–11
Table 5–12. Diagnostic Control Register
BIT
TYPE
FUNCTION
Arbiter performance enhancement feature. When enabled, this feature provides automatic tier operation for bus masters
that have been retried or that have pending delayed transactions. In this case, the bus master gets promoted to the highest
priority tier.
15
R/W
0 = Disabled (default)
1 = Enabled
Parity mode. Bit 14 is encoded as:
0 = Parity error passing enabled (default)
1 = Parity error passing disabled
14
13
R/W
R/W
Upstream lock enable. The bridge default is to disable upstream lock. When set, bit 13 enables upstream resource locking.
This bit is encoded as:
0 = Selects upstream lock disabled (default)
1 = Selects upstream lock enabled
Downstream lock enable. The bridge default is to enable downstream lock. When set, bit 12 enables downstream resource
locking. This bit is encoded as:
12
11
10
R/W
R/W
R/W
0 = Selects downstream lock disabled
1 = Selects downstream lock enabled (default)
Secondary-bus decode speed. The bridge defaults to medium decode speed on the secondary bus. Bit 11 selects between
medium and slow decode speed. This bit is encoded as:
0 = Secondary bus decodes at medium decode speed (default)
1 = Secondary bus decodes at slow decode speed
Primary-bus decode speed. The bridge defaults to medium decode speed on the primary bus. Bit 10 selects between
medium and slow decode speed. This bit is encoded as:
0 = Primary bus decodes at medium decode speed (default)
1 = Primary bus decodes at slow decode speed
9–8
7
R
Reserved. Bits 9 and 8 return 0s when read.
Arbiter timeout. When set, bit 0 enables SERR reporting when the arbiter timer expires (times out).
0 = SERR on arbiter timeout disabled (default)
R/W
1 = SERR on arbiter timeout enabled
Transaction ordering enable
0 = Disabled
6
5
R/W
R/W
1 = Enabled (default)
Secondary initial data phase counter extension
0 = Normal 16 clock to initial data phase (default)
1 = Extends initial data phase to 64 clocks
Primary initial data phase counter disable
0 = Enable 16 clocks initial data phase counter (default)
1 = Disable 16 clock initial data phase counter
4
R/W
Note: The secondary initial data phase counter is always enabled.
Primary initial data phase counter extension
0 = Normal 16 clocks to initial data phase (default)
1 = Extends initial data phase to 64 clocks
3
2
R/W
R/W
Immediate retry mode
0 = Immediate retry mode enabled (default)
1 = Immediate retry mode disabled
Bus parking bit. This bit determines where the PCI2250 internal arbiter parks the secondary bus. When this bit is set, the
arbiterparks the secondary bus on the bridge. When this bit is cleared, the arbiter parks the bus on the last device mastering
the secondary bus. This bit is encoded as:
1
0
R/W
R/W
0 = Park the secondary bus on the last secondary bus master (default)
1 = Park the secondary bus on the bridge
TI internal test mode bit.
5–12
5.15 Diagnostic Status Register
The diagnostic status register is used to reflect the bridge diagnostic status. See Table 5–13 for a complete
description of the register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Diagnostic status
R/C/
U
R/C/
U
R/C/
R/C/
U
Type
R
0
R
0
R
0
R
0
R
0
R
U
R
0
R
0
R
0
R
0
R
X
R
X
Default
X
X
0
0
X
Register:
Type:
Diagnostic status
Read-only, Read/Write
Offset:
Default:
5Eh
0X0Xh
Table 5–13. Diagnostic Status Register
BIT
TYPE
FUNCTION
15–12
R
Reserved. Bits 15–12 return 0s when read.
Bridge detected a parity error while mastering on the secondary bus. When set, bit 11 indicates that the secondary bus
master detected a parity error. Writing a 1 to this bit clears it.
0 = No parity error detected
11
10
R/C/U
1 = Parity error detected
Bridge detected a parity error while mastering on the primary bus. When set, bit 10 indicates that the primary bus master
detected a parity error. Writing a 1 to this bit clears it.
0 = No parity error detected
R/C/U
1 = Parity error detected
9
8
R
R
MS1 status. Returns the logical value of the MS1/BPCC input.
MS0 status. Returns the logical value of the MS0 input.
Arbiter timeout SERR status. When set, bit 0 indicates that SERR has occurred due to the expiration of the arbiter timer.
Writing a 1 to this bit clears it.
0 = No SERR (default)
7
R/C/U
1 = SERR occurred due to an arbiter timeout
6
5
R
R
R
Reserved. Bit 6 returns 0 when read.
HS_SWITCH status. This registers returns the logical value of the S_MFUNC input regardless of the value of MS0/MS1.
Reserved
4–3
External arbiter enable pin status. Bit 2 contains the current state of the external pin external arbiter enable.
2
1
R
0 = Signal low
1 = Signal high
Serial EEPROM block status. Bit 1 indicates the status of the serial EEPROM block. When set, bit 1 indicates that the serial
EEPROM block is busy.
R
0 = Serial EEPROM block not busy
1 = Serial EEPROM block busy
Arbiter timeout status. Bit 0 indicates the status of the arbiter timer. When set, bit 0 indicates that a bus master did not begin
the cycle within 16 clocks. Writing a 1 to this bit clears it. This bit is encoded as:
0 = No timeout (default).
0
R/C/U
1 = Master requesting the bus did not start cycle within 16 clocks.
5–13
5.16 Arbiter Request Mask Register
The arbiter request mask register contains the SERR enable on arbiter timeouts and the request mask controls. See
Table 5–14 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Arbiter request mask
R
0
R/W
0
R
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Arbiter request mask
Read-only, Read/Write
Offset:
Default:
62h
00h
Table 5–14. Arbiter Request Mask Register
BIT
TYPE
FUNCTION
7
R
Reserved. Bit 7 returns 0 when read.
Timeout automatic masking enable
6
5–4
3
R/W
R
0 = Masking not automatic (default)
1 = Allow masking after 16-clock timeout
Reserved. Bits 5 and 4 return 0s when read.
Request 3 (REQ3) mask bit
0 = Use request 3 (default)
1 = Ignore request 3
R/W
Request 2 (REQ2) mask bit
0 = Use request 2 (default)
1 = Ignore request 2
2
1
0
R/W
R/W
R/W
Request 1 (REQ1) mask bit
0 = Use request 1 (default)
1 = Ignore request 1
Request 0 (REQ0) mask bit
0 = Use request 0 (default)
1 = Ignore request 0
5–14
5.17 Arbiter Timeout Status Register
The arbiter timeout status register contains the status of each request (request 5–0) timeout. The timeout status bit
for the respective request is set if the device did not assert FRAME after 16 clocks. See Table 5–15 for a complete
description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Arbiter timeout status
R
0
R
0
R
0
R
0
R/C/U
0
R/C/U
0
R/C/U
0
R/C/U
0
Register:
Type:
Offset:
Default:
Arbiter timeout status
Read-only
63h
00h
Table 5–15. Arbiter Timeout Status Register
BIT
TYPE
FUNCTION
7–4
R
Reserved. Bits 7–4 return 0s when read.
Request 3 timeout status. Cleared by writing a 1.
3
2
1
0
R/C/U
0 = No timeout (default)
1 = Timeout has occurred
Request 2 timeout status. Cleared by writing a 1.
0 = No timeout (default)
R/C/U
R/C/U
R/C/U
1 = Timeout has occurred
Request 1 timeout status. Cleared by writing a 1.
0 = No timeout (default)
1 = Timeout has occurred
Request 0 timeout status. Cleared by writing a 1.
0 = No timeout (default)
1 = Timeout has occurred
5–15
5.18 P_SERR Event Disable Register
The P_SERR event disable register is used to enable/disable SERR event on the primary interface. All events are
enabled by default. See Table 5–16 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
P_SERR event disable
R
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R
0
Register:
Type:
P_SERR event disable
Read-only, Read/Write
Offset:
Default:
64h
00h
Table 5–16. P_SERR Event Disable Register
BIT
TYPE
FUNCTION
7
R
Reserved. Bit 7 returns 0 when read.
Master delayed read time-out
24
6
5
R/W
0 = P_SERR signaled on a master time-out after 2 retries on a delayed read (default).
1 = P_SERR is not signaled on a master time-out.
Master delayed write time-out.
24
R/W
R/W
0 = P_SERR signaled on a master time-out after 2 retries on a delayed write (default).
1 = P_SERR is not signaled on a master time-out.
Master abort on posted write transactions. When set, bit 4 enables P_SERR reporting on master aborts on posted write
transactions.
4
0 = Master aborts on posted writes enabled (default)
1 = Master aborts on posted writes disabled
Target abort on posted writes. When set, bit 3 enables P_SERR reporting on target aborts on posted write transactions.
0 = Target aborts on posted writes enabled (default).
3
2
R/W
R/W
1 = Target aborts on posted writes disabled.
Master posted write time-out
24
0 = P_SERR signaled on a master time-out after 2 retries on a posted write (default).
1 = P_SERR is not signaled on a master time-out.
Posted write parity error
1
0
R/W
R
0 = P_SERR signaled on a posted write parity error (default).
1 = P_SERR is not signaled on a posted write parity error.
Reserved. Bit 0 returns 0 when read.
5–16
5.19 Secondary Clock Control Register
The secondary clock control register is used to control the secondary clock outputs. See Table 5–17 for a complete
description of the register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Secondary clock control
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Register:
Type:
Secondary clock control
Read-only, Read/Write
Offset:
Default:
68h
0000h
Table 5–17. Secondary Clock Control Register
BIT
TYPE
FUNCTION
15–9
R
Reserved. Bits 15–9 return 0s when read.
Clockout4 disable.
8
R/W
0 = Clockout4 enabled (default)
1 = Clockout4 disabled and driven high
Clockout3 disable.
7–6
5–4
3–2
1–0
R/W
R/W
R/W
R/W
00, 01, 10 = Clockout3 enabled (00 default)
11 = Clockout3 disabled and driven high
Clockout2 disable.
00, 01, 10 = Clockout2 enabled (00 default)
11 = Clockout2 disabled and driven high
Clockout1 disable.
00, 01, 10 = Clockout1 enabled (00 default)
11 = Clockout1 disabled and driven high
Clockout0 disable.
00, 01, 10 = Clockout0 enabled (00 default)
11 = Clockout0 disabled and driven high
5–17
5.20 P_SERR Status Register
The P_SERR status register indicates what caused a SERR event on the primary interface. See Table 5–18 for a
complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
P_SERR status
R/C/U R/C/U
R
0
R/C/U
0
R/C/U
0
R/C/U
0
R/C/U
0
R
0
0
0
Register:
Type:
P_SERR status
Read-only, Read/Clear/Update
Offset:
Default:
6Ah
00h
Table 5–18. P_SERR Status Register
BIT
TYPE
FUNCTION
7
R
Reserved. Bit 7 returns 0 when read.
24
Master delayed read time-out. A 1 indicates that P_SERR was signaled because of a master time-out after 2 retries on
a delayed read.
6
5
R/C/U
24
Master delayed write time-out. A 1 indicates that P_SERR was signaled because of a master time-out after 2 retries on
R/C/U
R/C/U
a delayed write.
Master abort on posted write transactions. A 1 indicates that P_SERR was signaled because of a master abort on a posted
write.
4
3
2
R/C/U Target abort on posted writes. A 1 indicates that P_SERR was signaled because of a target abort on a posted write.
24
Master posted write time-out. A 1 indicates that P_SERR was signaled because of a master time-out after 2 retries on
R/C/U
a posted write.
1
0
R/C/U Posted write parity error. A 1 indicates that P_SERR was signaled because of parity error on a posted write.
Reserved. Bit 0 returns 0 when read.
R
5.21 PM Capability ID Register
The capability ID register identifies the linked list item as the register for PCI power management. The capability ID
register returns 01h when read, which is the unique ID assigned by the PCI SIG for the PCI location of the capabilities
pointer and the value.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Capability ID
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
1
Register:
Type:
Offset:
Default:
Capability ID
Read-only
DCh
01h
5–18
5.22 PM Next Item Pointer Register
The next item pointer register is used to indicate the next item in the linked list of PCI power management capabilities.
The next item pointer returns E4h in compact PCI mode, indicating that the PCI2250 supports more than one
extended capability, but in all other modes returns 00h, indicating that only one extended capability is supported.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Next item pointer
R
1
R
1
R
1
R
R
0
R
1
R
0
R
0
0
Register:
Type:
Offset:
Default:
Next item pointer
Read-only
DDh
E4h Compact PCI mode
00h All other modes
5.23 Power Management Capabilities Register
ThepowermanagementcapabilitiesregistercontainsinformationonthecapabilitiesofthePCI2250functionsrelated
to power management. The PCI2250 function supports D0, D1, D2, and D3 power states when MS1 is low. The
PCI2250 does not support any power states when MS1 is high. See Table 5–19 for a complete description of the
register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Power management capabilities
R
0
R
0
R
0
R
0
R
0
R
1
R
1
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
1
R
0
Register:
Type:
Offset:
Default:
Power management capabilities
Read-only
DEh
0602h or 0001h
Table 5–19. Power Management Capabilities Register
BIT
TYPE
FUNCTION
PME support. This five-bit field indicates the power states that the device supports asserting PME. A 0 for any of these bits
indicates that the PCI2250 cannot assert PME signal from that power state. For the PCI2250, these five bits return 00000b
when read, indicating that PME is not supported.
15–11
R
R
D2 support. This bit returns 1 when MS0 is 0, indicating that the bridge function supports the D2 device power state. This
bit returns 0 when MS0 is 1, indicating that the bridge function does not support the D2 device power state.
10
D1 support. This bit returns 1 when MS0 is 0, indicating that the bridge function supports the D1 device power state. This
bit returns 0 when MS0 is 1, indicating that the bridge function does not support the D1 device power state.
9
8–6
5
R
R
R
Reserved. Bits 8–6 return 0s when read.
Device specific initialization. This bit returns 0 when read, indicating that the bridge function does not require special
initialization (beyond the standard PCI configuration header) before the generic class device driver is able to use it.
4
3
R
R
Auxiliary power source. This bit returns a 0 because the PCI2250 does not support PME signaling.
PMECLK. This bit returns a 0 because the PME signaling is not supported.
Version. This three-bit register returns the PCI Bus Power Management Interface Specification revision.
2–0
R
001 = Revision 1.0, MS0 = 1
010 = Revision 1.1, MS0 = 0
5–19
5.24 Power Management Control/Status Register
The power management control/status register determines and changes the current power state of the PCI2250. The
contents of this register are not affected by the internally generated reset caused by the transition from D3 to D0
hot
state. See Table 5–20 for a complete description of the register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Power management control/status
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R/W
0
R/W
0
Register:
Type:
Power management control/status
Read-only, Read/Write
Offset:
Default:
E0h
0000h
Table 5–20. Power Management Capabilities Register
BIT
TYPE
FUNCTION
15
R
R
PME status. This bit returns a 0 when read because the PCI2250 does not support PME.
Data scale. This two-bit read-only field indicates the scaling factor to be used when interpreting the value of the
data register. These bits return only 00b, because the data register is not implemented.
14–13
Data select. This four-bit field is used to select which data is to be reported through the data register and
data-scale field. These bits return only 0000b, because the data register is not implemented.
12–9
R
8
R
R
PME enable. This bit returns a 0 when read because the PCI2250 does not support PME signaling.
Reserved. Bits 7–2 return 0s when read.
7–2
Powerstate. Thistwo-bitfieldisusedbothtodeterminethecurrentpowerstateofafunctionandtosetthefunction
into a new power state. The definition of the two-bit field is given below:
00 – D0
01 – D1
10 – D2
1–0
R/W
11 – D3
hot
5–20
5.25 PMCSR Bridge Support Register
The PMCSR bridge support register is required for all PCI bridges and supports PCI bridge specific functionality. See
Table 5–21 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
PMCSR bridge support
R
X
R
X
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
PMCSR bridge support
Read-only
E2h
X0h
Table 5–21. PMCSR Bridge Support Register
BIT
TYPE
FUNCTION
Bus power control enable. This bit returns the value of the MS1/BCC input.
0 = Bus power/ clock control disabled
7
R
1 = Bus power/clock control enabled
B2/B3 support for D3 . This bit returns the value of MS1/BCC input. When this bit is 1, the secondary clocks
hot
are stopped when the device is placed in D3 . When this bit is 0, the secondary clocks remain on in all device
hot
states.
6
R
R
Note: If the primary clock is stopped, then the secondary clocks will stop because the primary clock is used to
generate the secondary clocks.
5–0
Reserved. Bits 5–0 return 0s when read.
5.26 Data Register
The data register is an optional, 8-bit read–only register that provides a mechanism for the function to report
state-dependent operating data such as power consumed or heat dissipatin. The PCI2050 does not implement the
data register.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Data
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
Data
Read-only
E3h
00h
5–21
5.27 HS Capability ID Register
The HS capability ID register identifies the linked list item as the register for CPCI hot swap capabilities. The register
returns 06h when read, which is the unique ID assigned by the PICMG for PCI location of the capabilities pointer and
the value.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
HS capability ID
R
0
R
0
R
0
R
R
0
R
1
R
1
R
0
0
Register:
Type:
Offset:
Default:
HS capability ID
Read-only
E4h
06h
5.28 HS Next Item Pointer Register
The HS next item pointer register is used to indicate the next item in the linked list of CPCI hot swap capabilities. Since
the PCI2250 functions only include two capabilities list item, this register returns 0s when read.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
HS next item pointer
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Register:
Type:
Offset:
Default:
HS next item pointer
Read-only
E5h
00h
5–22
5.29 Hot Swap Control Status Register
The hot swap control status register contains control and status information for CPCI hot swap resources. See
Table 5–22 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
Name
Type
Default
Hot swap control status
R/C/U
0
R/C/U
0
R
0
R
0
R/W
0
R
0
R/W
0
R
0
Register:
Type:
Hot swap control status
Read-only, Read/Write
Offset:
Default:
E6h
00h
Table 5–22. Hot Swap Control Status Register
BIT
TYPE
FUNCTION
ENUM insertion status. When set, the ENUM output is driven by the PCI2250. This bit defaults to 0, and will be set after
R/C/U a PCI reset occurs, the ejector handle is closed, and bit 6 is 0. Thus, this bit is set following an insertion when the board
implementing the PCI2250 is ready for configuration. This bit cannot be set under software control.
7
ENUM extraction status. When set, the ENUM output is driven by the PCI2250. This bit defaults to 0, and is set when the
R/C/U ejectorhandleisopenedandbit7is0. Thus, thisbitissetwhentheboardimplementingthePCI2250isabouttoberemoved.
This bit cannot be set under software control.
6
5–4
R
Reserved. Bits 5 and 4 return 0s when read.
LED ON/OFF. This bit defaults to 0, and controls the external LED indicator (HSLED) under normal conditions. However,
for a duration following a PCI_RST, the HSLED output is driven high by the PCI2250 and this bit is ignored. When this bit
is interpreted, a 1 will cause HSLED high and a 0 will cause HSLED low.
3
R/W
Following PCI_RST, the HSLED output is driven high by the PCI2250 until the ejector handle is closed. When these
conditions are met, the HSLED is under software control via this bit.
2
1
0
R
R/W
R
Reserved. Bit 2 returns 0 when read.
ENUM interrupt mask. This bit allows the HSENUM output to be masked by software. Bits 6 and 7 are set independently
from this bit.
0 = Enable HSENUM output
1 = Mask HSENUM output
Reserved. Bit 0 returns 0 when read.
5–23
5–24
6 Electrical Characteristics
†
6.1 Absolute Maximum Ratings Over Operating Temperature Ranges
Supply voltage range: V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V
CC
: SV
: PV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6 V
CCP
CCP
Input voltage range, V : PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V
I
: TTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to V
+ 0.5 V
+ 0.5 V
CC
CC
Output voltage range, V : PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to V
O
Input clamp current, I (V < 0 or V > V ) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
IK
I
I
CC
Output clamp current, I
(V < 0 or V > V ) (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
OK
O O CC
Storage temperature range, T
Virtual junction temperature, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
J
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Applies for external input and bidirectional buffers. V > V
does not apply to fail-safe terminals.
does not apply to fail-safe terminals.
CC
I
CC
2. Applies to external output and bidirectional buffers. V > V
O
6–1
6.2 Recommended Operating Conditions (see Note 3)
OPERATION
MIN NOM
MAX UNIT
V
Supply voltage (core)
Commercial
Commercial
3.3 V
3.3 V
5 V
3
3
3.3
3.3
5
3.6
3.6
V
CC
PV
PCI primary bus I/O clamping rail voltage
V
CCP
CCP
4.75
3
5.25
3.6
3.3 V
5 V
3.3
5
SV
PCI secondary bus I/O clamping rail voltage
High-level input voltage
Commercial
PCI
V
V
4.75
5.25
3.3 V
5 V
0.5 V
V
V
CCP
2
CCP
†
V
IH
CCP
‡
TTL
PCI
3.3 V
3.3 V
5 V
2.25
0
V
CC
0.3 V
CCP
0.8
†
0
High-level input voltage
V
V
IL
‡
TTL
PCI
TTL
0
0
0
0
0
1
0
0
0
0.75
CCP
V
V
V
Input voltage
V
V
I
‡
V
V
V
CC
CC
3.3 V
5 V
§
Output voltage
O
CC
4
PCI
TTL
Input transition time (t and t )
nS
t
t
r
f
‡
6
3.3 V
5 V
25
25
70
Operating ambient temperature range
Virtual junction temperature
T
A
¶
°C
115
T
J
NOTES: 3. Unused or floating pins (input or I/O) must be held high or low.
†
‡
Applies for external input and bidirectional buffers without hysteresis
TTL terminals are Schmitt-trigger input-only terminals: 55, 69, 132, 174 for PGF-packaged device; and 49, 63, 120, 159 for PCM-packaged
device.
§
¶
Applies for external output buffers
These junction temperatures reflect simulation conditions. The customer is responsible for verifying junction temperature.
6.3 Recommended Operating Conditions for PCI Interface
OPERATION
MIN NOM
MAX
3.6
UNIT
V
V
Core voltage
Commercial
Commercial
3.3 V
3.3 V
5 V
3
3.3
3.3
5
V
CC
3
4.75
0
3.6
PCI supply voltage
V
V
V
V
V
CCP
5.25
3.3 V
5 V
V
CCP
CCP
CCP
CCP
V
V
V
V
Input voltage
I
0
V
V
V
3.3 V
5 V
0
§
Output voltage
O
0
3.3 V
5 V
0.5 V
CCP
2
¶
CMOS compatible
CMOS compatible
High-level input voltage
Low-level input voltage
IH
3.3 V
5 V
0.3 V
CCP
0.8
¶
IL
§
¶
Applies to external output buffers
Applies to external input and bidirectional buffers without hysteresis
6–2
6.4 Electrical Characteristics Over Recommended Operating Conditions
PARAMETER
TERMINALS
OPERATION
3.3 V
TEST CONDITIONS
MIN
0.9 V
MAX
UNIT
I
I
I
I
= –0.5 mA
CC
2.4
OH
†
V
V
High-level output voltage
OH
5 V
= –2 mA
= 1.5 mA
= 6 mA
OH
OL
OL
3.3 V
0.1 V
CC
0.55
Low-level output voltage
High-level input current
V
OL
V
5 V
§
§
TTL
V = V
I
1
CC
Input terminals
‡
PCI
V = V
I
10
I
IH
CCP
µA
¶
I/O terminals
V = V
I
10
–1
CCP
TTL
PCI
Input terminals
‡
–1
I
I
Low-level input current
V = GND
µA
µA
IL
I
¶
–10
±10
I/O terminals
High-impedance output current
V
O
= V
or GND
CCP
OZ
†
‡
§
¶
V
is not tested on PSERR due to open-drain configuration.
and I are not tested on NO_HSLED dur to its active ourput-only configuration.
OH
I
IH
IL
TTL terminals are 55, 69, 132, 174 for PGF-packaged device; and 49, 63, 120, 159 for PCM-packaged device.
For I/O terminals, the input leakage current includes the off-state output current I
.
OZ
6–3
6.5 PCI Clock/Reset Timing Requirements Over Recommended Ranges of Supply
Voltage and Operating Free-Air Temperature (see Figure 6–2 and Figure 6–3)
ALTERNATE
SYMBOL
MIN
MAX
UNIT
t
t
t
Cycle time, PCLK
t
30
11
11
1
∞
ns
ns
c
cyc
Pulse duration, PCLK high
Pulse duration, PCLK low
Slew rate, PCLK
t
high
wH
wL
t
ns
low
t , t
∆v/∆t
4
V/ns
ms
ms
r f
t
t
Pulse duration, RSTIN
t
1
w
rst
Setup time, PCLK active at end of RSTIN (see Note 4 )
t
100
su
rst-clk
NOTE 4: The setup and hold times for the secondary are identical to those for the primary; however, the times are relative to the secondary PCI
close.
6–4
6.6 PCI Timing Requirements Over Recommended Ranges of Supply Voltage and
Operating Free-Air Temperature (see Note 5 and Figure 6–1 and Figure 6–4)
ALTERNATE
SYMBOL
TEST CONDITIONS
MIN
MAX
UNIT
PCLK to shared signal
valid delay time
t
11
val
inv
t
Propagation delay time
Enable time,
C
= 50 pF, See Note 6
L
ns
pd
PCLK to shared signal
invalid delay time
t
2
2
t
t
t
ns
ns
en
on
off
high-impedance-to-active delay time from PCLK
Disable time,
t
28
dis
active-to-high-impedance delay time from PCLK
t
t
Setup time before PCLK valid
Hold time after PCLK high
t
, See Note 4
7
0
ns
ns
su
su
t , See Note 4
h
h
5. This data sheet uses the following conventions to describe time (t) intervals. The format is: t , where subscript A indicates the type
A
ofdynamicparameterbeingrepresented. Oneofthefollowingisused:t =propagationdelaytime, t = delay time, t = setup time,
pd su
d
and t = hold time.
h
6. PCI shared signals are AD31–AD0, C/BE3–C/BE0, FRAME, TRDY, IRDY, STOP, IDSEL, DEVSEL, and PAR.
6–5
6.7 Parameter Measurement Information
LOAD CIRCUIT PARAMETERS
†
I
OL
TIMING
C
I
I
V
LOAD
(pF)
OL
OH
LOAD
(V)
PARAMETER
(mA)
(mA)
t
0
3
PZH
Test
Point
t
50
8
–8
en
t
t
t
PZL
PHZ
PLZ
From Output
Under Test
V
LOAD
t
t
50
50
8
8
–8
–8
1.5
‡
dis
pd
C
LOAD
†
‡
C
V
includes the typical load-circuit distributed capacitance.
LOAD
LOAD
I
OH
– V
OL
= 50 Ω, where V
= 0.6 V, I
= 8 mA
OL
OL
I
OL
LOAD CIRCUIT
V
Timing
Input
(see Note A )
CC
V
CC
50% V
High-Level
Input
CC
50% V
50% V
CC
CC
0 V
0 V
t
h
t
su
t
w
Data
Input
V
CC
90% V
CC
V
CC
50% V
50% V
10% V
CC
CC
CC
t
Low-Level
Input
0 V
50% V
50% V
CC
CC
0 V
t
f
r
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PULSE DURATION
INPUT RISE AND FALL TIMES
V
CC
Output
Control
(low-level
enabling)
50% V
50% V
CC
CC
V
0 V
CC
Input
(see Note A)
t
50% V
50% V
CC
PZL
CC
t
PLZ
0 V
t
pd
V
t
CC
pd
≈ 50% V
V
Waveform 1
(see Note B)
CC
CC
OH
50% V
CC
In-Phase
Output
V
+ 0.3 V
OL
50% V
50% V
CC
CC
V
OL
V
OL
t
PHZ
t
pd
t
PZH
t
pd
V
OH
V
OH
V
– 0.3 V
OH
Out-of-Phase
Output
Waveform 2
(see Note B)
50% V
CC
50% V
50% V
CC
CC
≈ 50% V
0 V
V
OL
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NOTES: A. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by pulse generators having the
following characteristics: PRR = 1 MHz, Z = 50 Ω, t ≤ 6 ns, t ≤ 6 ns.
O
r
f
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. For t
and t
, V
PHZ OL
and V
are measured values.
OH
PLZ
Figure 6–1. Load Circuit and Voltage Waveforms
6–6
6.8 PCI Bus Parameter Measurement Information
t
wH
t
wL
2 V
0.8 V
2 V min Peak to Peak
t
t
f
r
t
c
Figure 6–2. PCLK Timing Waveform
PCLK
t
w
RSTIN
t
su
Figure 6–3. RSTIN Timing Waveforms
PCLK
1.5 V
t
t
pd
1.5 V
pd
t
Valid
PCI Output
PCI Input
t
off
on
Valid
t
su
t
h
Figure 6–4. Shared-Signals Timing Waveforms
6–7
6–8
7 Mechanical Data
PGF (S-PQFP-G176)
PLASTIC QUAD FLATPACK
132
89
133
88
0,27
0,17
M
0,08
0,50
0,13 NOM
176
45
1
44
Gage Plane
21,50 SQ
24,20
SQ
23,80
26,20
25,80
0,25
0,05 MIN
0°–ā7°
SQ
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040134/B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
7–1
PCM (S-PQFP-G***)
PLASTIC QUAD FLATPACK
144 PINS SHOWN
NO. OF
A
108
73
PINS***
22,75 TYP
25,35 TYP
144
160
109
72
0,38
0,22
M
0,13
0,65
144
37
0,16 NOM
1
36
A
28,20
Gage Plane
SQ
SQ
27,80
31,45
30,95
0,25
0,25 MIN
3,60
3,20
1,03
0,73
Seating Plane
0,10
4,10 MAX
4040024/B 10/94
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-022
D. The 144 PCM is identical to the 160 PCM except that four leads per corner are removed.
7–2
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明