PCM1796 [TI]
123dB SNR 立体声 DAC(软件控制);型号: | PCM1796 |
厂家: | TEXAS INSTRUMENTS |
描述: | 123dB SNR 立体声 DAC(软件控制) |
文件: | 总62页 (文件大小:744K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ꢊ
ꢦꢠ
ꢠ
ꢉ
ꢊ
ꢠ
ꢟ
ꢯ
ꢝ
ꢀ
ꢠ
ꢟ
ꢫ
ꢦ
ꢥ
ꢣ
ꢤ
ꢞ
ꢠ
ꢟ
ꢡ
ꢌ
ꢧ
ꢮ
ꢢ
ꢤ
ꢋ
ꢝ
ꢤ
ꢣ
ꢠ
ꢦ
ꢡ
ꢧ
ꢝ
ꢣ
ꢤ
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ꢇ
ꢈ
ꢉ
ꢊ
ꢋ
ꢌ
ꢍ
ꢃ
ꢅ
ꢇ
ꢉ
ꢎ
ꢏ
ꢐ
ꢑ
ꢒ
ꢂ
ꢀ
ꢓ
ꢋ
ꢔ
ꢕ
ꢍ
ꢒ
ꢖ
ꢗ
ꢒ
ꢔ
ꢁ
ꢘ
ꢖ
ꢁ
ꢑ
ꢘ
ꢕ
ꢂ
ꢘ
ꢔ
ꢌ
ꢍ
ꢒ
ꢙ
ꢖ
ꢋ
ꢚ
ꢑ
ꢌ
ꢘ
ꢛ
ꢘ
ꢚ
ꢖ
ꢋ
ꢕ
ꢋ
ꢌ
ꢒ
ꢓ
ꢉ
ꢌ
ꢚ
ꢉ
ꢒ
ꢔ
ꢒ
ꢓ
ꢚ
ꢕ
ꢚ
ꢔ
ꢗ
ꢘ
ꢛ
ꢌ
ꢘ
ꢛ
D
D
5-V Tolerant Digital Inputs
FEATURES
Small 28-Lead SSOP Package
D
24-Bit Resolution
D
Analog Performance:
− Dynamic Range: 123 dB
− THD+N: 0.0005%
APPLICATIONS
D
D
D
D
D
D
D
A/V Receivers
D
D
Differential Current Output: 4 mA p-p
SACD Players
8× Oversampling Digital Filter:
− Stop-Band Attenuation: –98 dB
− Pass-Band Ripple: 0.0002 dB
DVD Players
HDTV Receivers
D
D
Sampling Frequency: 10 kHz to 200 kHz
System Clock: 128, 192, 256, 384, 512, or
Car Audio Systems
Digital Multitrack Recorders
Other Applications Requiring 24-Bit Audio
768 f With Autodetect
S
D
Accepts 16-, 20-, and 24-Bit Audio Data
2
D
PCM Data Formats: Standard, I S, and
Left-Justified
DESCRIPTION
The PCM1796 is a monolithic CMOS integrated circuit that
includes stereo digital-to-analog converters and support
circuitry in a small 28-lead SSOP package. The data
converters use TI’s advanced segment DAC architecture
to achieve excellent dynamic performance and improved
tolerance to clock jitter. The PCM1796 provides balanced
current outputs, allowing the user to optimize analog
performance externally. The PCM1796 accepts PCM and
DSD audio data formats, providing easy interfacing to
audio DSP and decoder chips. The PCM1796 also
interfaces with external digital filter devices (DF1704,
DF1706, PMD200). Sampling rates up to 200 kHz are
supported. A full set of user-programmable functions is
accessible through an SPI or I2C serial control port, which
supports register write and readback functions. The
PCM1796 also supports the time division multiplexed
command and audio (TDMCA) data format.
D
D
DSD Format Interface Available
Interface Available for Optional External
Digital Filter or DSP
2
D
TDMCA or Serial Port (SPI/I C)
D
User-Programmable Mode Controls:
− Digital Attenuation: 0 dB to –120 dB,
0.5 dB/Step
− Digital De-Emphasis
− Digital Filter Rolloff: Sharp or Slow
− Soft Mute
− Zero Flag for Each Output
D
D
Compatible With PCM1792 (Pins and Mode
Controls)
Dual Supply Operation:
− 5-V Analog, 3.3-V Digital
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate
precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to
damage because very small parametric changes could cause the device not to meet its published specifications.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢀꢛ ꢚ ꢖꢙ ꢁ ꢌꢋ ꢚꢔ ꢖ ꢒꢌꢒ ꢜꢝ ꢞꢟ ꢠ ꢡꢢ ꢣꢜꢟꢝ ꢜꢤ ꢥꢦ ꢠ ꢠ ꢧꢝꢣ ꢢꢤ ꢟꢞ ꢨꢦꢩ ꢪꢜꢥ ꢢꢣꢜ ꢟꢝ ꢫꢢ ꢣꢧꢬ ꢀꢠ ꢟꢫꢦ ꢥꢣꢤ
ꢥ ꢟꢝ ꢞꢟꢠ ꢡ ꢣꢟ ꢤ ꢨꢧ ꢥ ꢜ ꢞꢜ ꢥ ꢢ ꢣꢜ ꢟꢝꢤ ꢨ ꢧꢠ ꢣꢭꢧ ꢣꢧ ꢠ ꢡꢤ ꢟꢞ ꢌꢧꢮ ꢢꢤ ꢋꢝꢤ ꢣꢠ ꢦꢡ ꢧꢝꢣ ꢤ ꢤꢣ ꢢꢝꢫ ꢢꢠ ꢫ ꢯ ꢢꢠ ꢠ ꢢ ꢝꢣꢰꢬ
ꢀꢠ ꢟ ꢫꢦꢥ ꢣ ꢜꢟ ꢝ ꢨꢠ ꢟ ꢥ ꢧ ꢤ ꢤ ꢜꢝ ꢱ ꢫꢟ ꢧ ꢤ ꢝꢟꢣ ꢝꢧ ꢥꢧ ꢤꢤ ꢢꢠ ꢜꢪ ꢰ ꢜꢝꢥ ꢪꢦꢫ ꢧ ꢣꢧ ꢤꢣꢜ ꢝꢱ ꢟꢞ ꢢꢪ ꢪ ꢨꢢ ꢠ ꢢꢡ ꢧꢣꢧ ꢠ ꢤꢬ
Copyright 2006, Texas Instruments Incorporated
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ORDERING INFORMATION
OPERATION
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA
PRODUCT
PACKAGE
PACKAGE CODE
PCM1796DB
Tube
PCM1796DB
28-lead SSOP
28DB
–25°C to 85°C
PCM1796
PCM1796DBR
Tape and reel
ABSOLUTE MAXIMUM RATINGS
(1)
over operating free-air temperature range unless otherwise noted
PCM1796
V
V
1, V 2L, V 2R
CC CC
–0.3 V to 6.5 V
–0.3 V to 4 V
0.1 V
CC
DD
Supply voltage
Supply voltage differences: V 1, V 2L, V 2R
CC CC CC
Ground voltage differences: AGND1, AGND2, AGND3L, AGND3R, DGND
0.1 V
(2) (2)
(2)
(2)
LRCK, DATA, BCK, SCK, MSEL, RST, MS , MDI, MC, MDO , ZEROL , ZEROR
(3) (3) (3) (3)
ZEROL , ZEROR , MDO , MS
–0.3 V to 6.5 V
Digital input
voltage
–0.3 V to (V
+ 0.3 V) < 4 V
DD
+ 0.3 V) < 6.5 V
Analog input voltage
–0.3 V to (V
CC
Input current (any pins except supplies)
Ambient temperature under bias
Storage temperature
10 mA
–40°C to 125°C
–55°C to 150°C
150°C
Junction temperature
Lead temperature (soldering)
Package temperature (IR reflow, peak)
260°C, 5 s
260°C
(1)
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2)
(3)
2
Input mode or I C mode
2
Output mode except for I C mode
ELECTRICAL CHARACTERISTICS
all specifications at T = 25°C, V 1 = V 2L = V 2R = 5 V, V
= 3.3 V, f = 44.1 kHz, system clock = 256 f , and 24-bit data unless
A
CC
CC
CC
DD
S
S
otherwise noted
PCM1796DB
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
MAX
RESOLUTION
24
Bits
DATA FORMAT (PCM Mode)
Audio data interface format
Audio data bit length
2
Standard, I S, left-justified
16-, 20-, 24-bit selectable
MSB first, twos complement
Audio data format
f
S
Sampling frequency
10
200
kHz
System clock frequency
128, 192, 256, 384, 512, 768 f
S
DATA FORMAT (DSD Mode)
Audio data interface format
Audio data bit length
DSD (direct stream digital)
1 Bit
f
S
Sampling frequency
2.8224
MHz
MHz
System clock frequency
2.8224
11.2896
2
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ELECTRICAL CHARACTERISTICS (Continued)
all specifications at T = 25°C, V 1 = V 2L = V 2R = 5 V, V
= 3.3 V, f = 44.1 kHz, system clock = 256 f , and 24-bit data unless
A
CC
CC
CC
DD
S
S
otherwise noted
PCM1796DB
TYP
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
DIGITAL INPUT/OUTPUT
Logic family
TTL compatible
V
V
2
IH
IL
Input logic level
Input logic current
Output logic level
VDC
µA
0.8
I
IH
I
IL
V
V
= V
DD
= 0 V
10
IN
IN
–10
V
I
I
= –2 mA
= 2 mA
2.4
OH
OL
OH
OL
VDC
V
0.4
(1)(2)
DYNAMIC PERFORMANCE (PCM MODE)
f
f
f
= 44.1 kHz
= 96 kHz
0.0005%
0.001%
0.0015%
123
0.001%
S
S
S
THD+N at V
OUT
= 0 dB
= 192 kHz
EIAJ, A-weighted, f = 44.1 kHz
S
EIAJ, A-weighted, f = 96 kHz
S
120
120
116
123
Dynamic range
dB
dB
EIAJ, A-weighted, f = 192 kHz
123
S
EIAJ, A-weighted, f = 44.1 kHz
S
EIAJ, A-weighted, f = 96 kHz
S
123
123
Signal-to-noise ratio
Channel separation
EIAJ, A-weighted, f = 192 kHz
123
S
f
S
f
S
f
S
= 44.1 kHz
= 96 kHz
119
118
dB
dB
= 192 kHz
117
Level Linearity Error
V
OUT
= –120 dB
1
(1)(2)(3)
DYNAMIC PERFORMANCE (MONO MODE)
f
f
f
= 44.1 kHz
= 96 kHz
0.0005%
0.001%
0.0015%
126
S
S
S
THD+N at V
OUT
= 0 dB
= 192 kHz
EIAJ, A-weighted, f = 44.1 kHz
S
EIAJ, A-weighted, f = 96 kHz
S
126
Dynamic range
dB
dB
EIAJ, A-weighted, f = 192 kHz
126
S
EIAJ, A-weighted, f = 44.1 kHz
S
EIAJ, A-weighted, f = 96 kHz
S
126
126
Signal-to-noise ratio
EIAJ, A-weighted, f = 192 kHz
126
S
(1)
Filter condition:
THD+N: 20-Hz HPF, 20-kHz AES17 LPF
Dynamic range: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted
Signal-to-noise ratio: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted
Channel separation: 20-Hz HPF, 20-kHz AES17 LPF
Analog performance specifications are measured using the System Twot Cascade audio measurement system by Audio Precision in the
averagingmode.
(2)
(3)
Dynamic performance and dc accuracy are specified at the output of the postamplifier as shown in Figure 36.
Dynamic performance and dc accuracy are specified at the output of the measurement circuit as shown in Figure 38.
Audio Precision and System Two are trademarks of Audio Precision, Inc.
Other trademarks are the property of their respective owners.
3
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ELECTRICAL CHARACTERISTICS (Continued)
all specifications at T = 25°C, V 1 = V 2L = V 2R = 5 V, V
= 3.3 V, f = 44.1 kHz, system clock = 256 f , and 24-bit data unless
A
CC
CC
CC
DD
S
S
otherwise noted
PCM1796DB
TYP
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
(1) (2)
DSD MODE DYNAMIC PERFORMANCE
THD+N at FS
(44.1 kHZ, 64 f )
S
2 V rms
0.0007%
122
Dynamic range
–60 dB, EIAJ, A-weighted
dB
dB
Signal-to-noise ratio
ANALOG OUTPUT
Gain error
EIAJ, A-weighted
122
–7
2
0.5
0.5
4
7
3
2
% of FSR
% of FSR
% of FSR
mA p-p
mA
Gain mismatch, channel-to-channel
Bipolar zero error
–3
–2
At BPZ
Output current
Full scale (0 dB)
At BPZ
Center current
–3.5
DIGITAL FILTER PERFORMANCE
De-emphasis error
0.1
dB
FILTER CHARACTERISTICS–1: SHARP ROLLOFF
0.0002 dB
–3 dB
0.454 f
S
Pass band
0.49 f
S
Stop band
0.546 f
S
Pass-band ripple
0.0002
dB
dB
s
Stop-band attenuation
Delay time
Stop band = 0.546 f
–98
S
38/f
S
FILTER CHARACTERISTICS–2: SLOW ROLLOFF
0.001 dB
–3 dB
0.21 f
S
Pass band
0.448 f
S
Stop band
0.79 f
S
Pass-band ripple
Stop-band attenuation
Delay time
0.001
dB
dB
s
Stop band = 0.732 f
–80
S
38/f
S
(1)
Filter condition:
THD+N: 20-Hz HPF, 20-kHz AES17 LPF
Dynamic range: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted
Signal-to-noise ratio: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted
Channel separation: 20-Hz HPF, 20-kHz AES17 LPF
Analog performance specifications are measured using the System Two Cascade audio measurement system by Audio Precision in the averaging
mode.
(2)
Dynamic performance and dc accuracy are specified at the output of the postamplifier as shown in Figure 37.
4
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ELECTRICAL CHARACTERISTICS (Continued)
all specifications at T = 25°C, V 1 = V 2L = V 2R = 5 V, V
= 3.3 V, f = 44.1 kHz, system clock = 256 f , and 24-bit data unless
A
CC
CC
CC
DD
S
S
otherwise noted
PCM1796DB
TYP
PARAMETER
POWER SUPPLY REQUIREMENTS
TEST CONDITIONS
UNIT
MIN
MAX
V
V
V
V
3
3.3
5
3.6
VDC
VDC
DD
CC
CC
CC
1
Voltage range
2L
2R
4.75
5.25
9
f
S
f
S
f
S
f
S
f
S
f
S
f
S
f
S
f
S
= 44.1 kHz
= 96 kHz
7
13
I
mA
mA
mW
DD
= 192 kHz
= 44.1 kHz
= 96 kHz
25
(1)
Supply current
18
23
19
I
CC
= 192 kHz
= 44.1 kHz
= 96 kHz
20
115
140
180
150
(1)
Power dissipation
= 192 kHz
TEMPERATURE RANGE
Operation temperature
Thermal resistance
–25
85
°C
θ
28-pin SSOP
100
°C/W
JA
(1)
Input is BPZ data.
PIN ASSIGNMENTS
PCM1796
(TOP VIEW)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
ZEROL
V
2L
CC
2
ZEROR
MSEL
LRCK
DATA
BCK
AGND3L
3
I
I
L–
L+
OUT
4
OUT
5
AGND2
6
V
V
V
1
CC
7
SCK
DGND
L
R
COM
COM
REF
8
9
V
I
DD
MS
MDI
MC
MDO
RST
10
11
12
13
14
AGND1
I
I
R–
R+
OUT
OUT
AGND3R
2R
V
CC
5
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Terminal Functions
TERMINAL
I/O
DESCRIPTIONS
NAME
AGND1
AGND2
AGND3L
AGND3R
BCK
PIN
19
24
27
16
6
–
–
Analog ground (internal bias)
Analog ground (internal bias)
–
Analog ground (L-channel DACFF)
Analog ground (R-channel DACFF)
–
(1)
Bit clock input
I
(1)
DATA
5
I
Serial audio data input
DGND
8
–
Digital ground
I
I
I
I
I
L+
L–
R+
R–
25
26
17
18
20
4
O
O
O
O
–
L-channel analog current output+
L-channel analog current output–
R-channel analog current output+
R-channel analog current output–
Output current reference bias pin
OUT
OUT
OUT
OUT
REF
(1)
Left and right clock (f ) input
LRCK
MC
I
S
(1)
12
11
13
10
3
I
Mode control clock input
(1)
Mode control data input
MDI
I
(3)
Mode control readback data output
MDO
MS
I/O
I/O
I
(2)
Mode control chip-select input
2
(1)
MSEL
RST
SCK
I C/SPI select
(1)
14
7
I
Reset
System clock input
Analog power supply, 5 V
(1)
I
V
V
V
V
V
V
1
23
28
15
22
21
9
–
CC
CC
CC
2L
2R
–
Analog power supply (L-channel DACFF), 5 V
Analog power supply (R-channel DACFF), 5 V
L-channel internal bias decoupling pin
R-channel internal bias decoupling pin
Digital power supply, 3.3 V
–
L
–
COM
COM
DD
R
–
–
(2)
ZEROL
ZEROR
1
I/O
I/O
Zero flag for L-channel
Zero flag for R-channel
(2)
2
(1)
(2)
(3)
Schmitt-trigger input, 5-V tolerant
Schmitt-trigger input and output. 5-V tolerant input and CMOS output
Schmitt-trigger input and output. 5-V tolerant input. In I C mode, this pin becomes an open-drain 3-state output; otherwise, this pin is a CMOS
output.
2
6
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
FUNCTIONAL BLOCK DIAGRAM
I
I
L–
L+
OUT
LRCK
BCK
Current
Segment
DAC
V
OUT
L
DATA
Audio
Data Input
I/F
OUT
RST
I/V and Filter
8
V
L
COM
Oversampling
Digital
Advanced
Segment
DAC
Bias
and
Vref
I
REF
Filter
and
Function
Control
MDO
V
COM
R
Modulator
MDI
MC
I
R–
OUT
OUT
Function
Control
I/F
MS
Current
Segment
DAC
V R
OUT
MSEL
I
R+
I/V and Filter
ZEROL
ZEROR
System
Clock
Manager
Zero
Detect
Power Supply
7
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
TYPICAL PERFORMANCE CURVES
DIGITAL FILTER
Digital Filter Response
AMPLITUDE
AMPLITUDE
vs
vs
FREQUENCY
FREQUENCY
0
−20
0.0005
0.0004
0.0003
−40
0.0002
−60
0.0001
−80
0
–0.0001
−100
−120
−140
−160
–0.0002
–0.0003
–0.0004
–0.0005
0.0
0
1
2
3
4
0.1
0.2
0.3
0.4
0.5
Frequency[× f ]
Frequency[× f ]
S
S
Figure 1. Frequency Response, Sharp Rolloff
Figure 2. Pass-Band Ripple, Sharp Rolloff
AMPLITUDE
vs
AMPLITUDE
vs
FREQUENCY
FREQUENCY
0
−20
0
−2
−4
−40
−6
−60
−8
−80
−10
−12
−14
−16
−18
−20
−100
−120
−140
−160
0
1
2
3
4
0.0
0.1
0.2
0.3
0.4
0.5
0.6
Frequency[× f ]
Frequency[× f ]
S
S
Figure 3. Frequency Response, Slow Rolloff
Figure 4. Transition Characteristics, Slow Rolloff
8
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
De-Emphasis Filter
DE-EMPHASIS LEVEL
DE-EMPHASIS ERROR
vs
vs
FREQUENCY
FREQUENCY
0
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
0.5
0.4
0.3
0.2
0.1
f
= 32 kHz
f
S
= 32 kHz
S
0.0
−0.1
−0.2
−0.3
−0.4
−0.5
0
2
4
6
8
10
12
14
0
2
4
6
8
10
12
14
f – Frequency – kHz
f – Frequency – kHz
Figure 5
Figure 6
DE-EMPHASIS LEVEL
vs
DE-EMPHASIS ERROR
vs
FREQUENCY
FREQUENCY
0
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
0.5
0.4
0.3
0.2
0.1
f
= 44.1 kHz
f
S
= 44.1 kHz
S
0.0
−0.1
−0.2
−0.3
−0.4
−0.5
0
2
4
6
8
10 12 14 16 18 20
0
2
4
6
8
10 12 14 16 18 20
f – Frequency – kHz
f – Frequency – kHz
Figure 7
Figure 8
9
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
De-Emphasis Filter (Continued)
DE-EMPHASIS LEVEL
vs
DE-EMPHASIS ERROR
vs
FREQUENCY
FREQUENCY
0
0.5
0.4
0.3
0.2
0.1
f
S
= 48 kHz
f = 48 kHz
S
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
0.0
−0.1
−0.2
−0.3
−0.4
−0.5
0
2
4
6
8
10 12 14 16 18 20 22
0
2
4
6
8
10 12 14 16 18 20 22
f – Frequency – kHz
f – Frequency – kHz
Figure 9
Figure 10
10
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ANALOG DYNAMIC PERFORMANCE
Supply Voltage Characteristics
TOTAL HARMONIC DISTORTION + NOISE
DYNAMIC RANGE
vs
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
126
124
122
120
118
116
0.01
f
= 96 kHz
= 48 kHz
S
f
S
f
= 192 kHz
S
0.001
f
S
= 192 kHz
f
S
= 48 kHz
f
S
= 96 kHz
5.25
0.0001
4.50
4.75
5.00
5.50
4.50
4.75
5.00
5.25
5.50
V
CC
– Supply Voltage – V
V
CC
– Supply Voltage – V
Figure 12
Figure 11
SIGNAL-to-NOISE RATIO
vs
CHANNEL SEPARATION
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
126
124
122
120
118
116
122
120
118
116
114
112
f
= 96 kHz
S
f
= 96 kHz
S
f
S
= 48 kHz
f
S
= 192 kHz
f
= 48 kHz
S
f
S
= 192 kHz
4.50
4.75
5.00
5.25
5.50
4.50
4.75
V
5.00
5.25
5.50
V
– Supply Voltage – V
– Supply Voltage – V
CC
CC
Figure 13
Figure 14
NOTE: PCM mode, T = 25°C, V
DD
= 3.3 V, measurement circuit is Figure 36.
A
11
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Temperature Characteristics
TOTAL HARMONIC DISTORTION + NOISE
DYNAMIC RANGE
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
126
124
122
120
118
116
0.01
f
= 96 kHz
S
f
= 48 kHz
S
f
= 192 kHz
S
f
S
= 96 kHz
0.001
f
= 192 kHz
S
f
S
= 48 kHz
0.0001
−50
−25
0
25
50
75
100
−50
−25
0
25
50
75
100
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 15
Figure 16
SIGNAL-to-NOISE RATIO
vs
CHANNEL SEPARATION
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
126
124
122
120
118
116
122
120
118
116
114
112
f
= 96 kHz
S
f
= 96 kHz
S
f
S
= 192 kHz
f
= 48 kHz
S
f
= 48 kHz
S
f
= 192 kHz
S
−50
−25
0
25
50
75
100
−50
−25
0
25
50
75
100
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 17
Figure 18
NOTE: PCM mode, V
= 3.3 V, V = 5 V, measurement circuit is Figure 36.
CC
DD
12
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
AMPLITUDE
vs
AMPLITUDE
vs
FREQUENCY
FREQUENCY
0
−20
0
−20
−40
−40
−60
−60
−80
−80
−100
−120
−140
−160
−100
−120
−140
−160
0
2
4
6
8
10 12 14 16 18 20
0
10 20 30 40 50 60 70 80 90 100
f – Frequency – kHz
f – Frequency – kHz
NOTE: PCM mode, f = 48 kHz, 32768 point 8 average, T = 25°C, NOTE: PCM mode, f = 96 kHz, 32768 point 8 average, T = 25°C,
S
A
S
A
V
DD
= 3.3 V V
= 5 V, measurement circuit is Figure 36.
V
DD
= 3.3 V V
= 5 V, measurement circuit is Figure 36.
CC
CC
Figure 19. –60-dB Output Spectrum, BW = 20 kHz Figure 20. –60-dB Output Spectrum, BW = 100 kHz
AMPLITUDE
TOTAL HARMONIC DISTORTION + NOISE
vs
vs
FREQUENCY
INPUT LEVEL
0
10
−20
1
−40
−60
0.1
−80
0.01
−100
−120
−140
−160
0.001
0.0001
0
2
4
6
8
10 12 14 16 18 20
−90 −80 −70 −60 −50 −40 −30 −20 −10
0
f – Frequency – kHz
Input Level – dBFS
NOTE: PCM mode, f = 48 kHz, T = 25°C, V
DD
= 3.3 V, V = 5 V, NOTE: DSD mode (FIR-2), 32768 point 8 average, T = 25°C,
CC A
S
A
measurement circuit is Figure 36.
V
= 3.3 V, V = 5 V, measurement circuit is Figure 37.
DD
CC
Figure 21. THD+N vs Input Level, PCM Mode
Figure 22. –60-dB Output Spectrum, DSD Mode
13
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
SYSTEM CLOCK AND RESET FUNCTIONS
System Clock Input
The PCM1796 requires a system clock for operating the digital interpolation filters and advanced segment DAC
modulators. The system clock is applied at the SCK input (pin 7). The PCM1796 has a system clock detection circuit
that automatically senses the frequency at which the system clock is operating. Table 1 shows examples of system
clock frequencies for common audio sampling rates. If the oversampling rate of the delta-sigma modulator is selected
as 128 f , the system clock frequency is required to be over 256 f .
S
S
Figure 23 shows the timing requirements for the system clock input. For optimal performance, it is important to use
a clock source with low phase jitter and noise. One of the Texas Instruments PLL1700 family of multiclock generators
is an excellent choice for providing the PCM1796 system clock.
Table 1. System Clock Rates for Common Audio Sampling Frequencies
SYSTEM CLOCK FREQUENCY (f
) (MHz)
512 f
SCK
SAMPLING FREQUENCY
128 f
192 f
256 f
384 f
768 f
S
S
S
S
S
S
(1)
(1)
32 kHz
44.1 kHz
48 kHz
4.096
6.144
8.192
11.2896
12.288
24.576
12.288
16.9344
18.432
36.864
16.384
24.576
33.8688
36.864
(1)
5.6488
8.4672
9.216
22.5792
24.576
(1)
6.144
(1)
49.152
(1)
73.728
96 kHz
12.288
24.576
18.432
36.864
(1)
49.152
(1)
73.728
(2)
—
(2)
—
192 kHz
(1)
(2)
2
This system clock rate is not supported in I C fast mode.
This system clock rate is not supported for the given sampling frequency.
t
(SCKH)
H
2 V
System Clock (SCK)
0.8 V
L
t
(SCKL)
t
(SCY)
PARAMETERS
MIN
MAX UNITS
t
System clock pulse cycle time
13
ns
ns
ns
(SCY)
t
System clock pulse duration, HIGH
System clock pulse duration, LOW
0.4t
(SCY)
(SCKH)
t
0.4t
(SCY)
(SCKL)
Figure 23. System Clock Input Timing
14
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Power-On and External Reset Functions
The PCM1796 includes a power-on reset function. Figure 24 shows the operation of this function. With V
> 2 V,
DD
the power-on reset function is enabled. The initialization sequence requires 1024 system clocks from the time
> 2 V. After the initialization period, the PCM1796 is set to its default reset state, as described in the MODE
V
DD
CONTROL REGISTERS section of this data sheet.
The PCM1796 also includes an external reset capability using the RST input (pin 14). This allows an external
controller or master reset circuit to force the PCM1796 to initialize to its default reset state.
Figure 25 shows the external reset operation and timing. The RST pin is set to logic 0 for a minimum of 20 ns. The
RST pin is then set to a logic 1 state, thus starting the initialization sequence, which requires 1024 system clock
periods. The external reset is especially useful in applications where there is a delay between the PCM1796 power
up and system clock activation.
V
DD
2.4 V (Max)
2 V (Typ)
1.6 V (Min)
Reset
Reset Removal
Internal Reset
System Clock
1024 System Clocks
Figure 24. Power-On Reset Timing
RST (Pin 14)
1.4 V
t
(RST)
Reset
Reset Removal
Internal Reset
System Clock
1024 System Clocks
PARAMETERS
Reset pulse duration, LOW
MIN
MAX UNITS
t
20
ns
(RST)
Figure 25. External Reset Timing
15
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
AUDIO DATA INTERFACE
Audio Serial Interface
The audio interface port is a 3-wire serial port. It includes LRCK (pin 4), BCK (pin 6), and DATA (pin 5). BCK is the
serial audio bit clock, and it is used to clock the serial data present on DATA into the serial shift register of the audio
interface. Serial data is clocked into the PCM1796 on the rising edge of BCK. LRCK is the serial audio left/right word
clock.
The PCM1796 requires the synchronization of LRCK and system clock, but does not need a specific phase relation
between LRCK and system clock.
If the relationship between LRCK and system clock changes more than 6 BCK, internal operation is initialized within
1/f and analog outputs are forced to the bipolar zero level until resynchronization between LRCK and system clock
S
is completed.
PCM Audio Data Formats and Timing
2
The PCM1796 supports industry-standard audio data formats, including standard right-justified, I S, and
left-justified. The data formats are shown in Figure 27. Data formats are selected using the format bits, FMT[2:0],
2
in control register 18. The default data format is 24-bit I S. All formats require binary 2s complement, MSB-first audio
data. Figure 26 shows a detailed timing diagram for the serial audio interface.
1.4 V
1.4 V
1.4 V
LRCK
BCK
t
t
(BCL)
t
(BCH)
(LB)
t
t
(BCY)
(BL)
DATA
t
t
(DS)
(DH)
PARAMETERS
MIN MAX UNITS
t
t
t
t
t
t
t
BCK pulse cycle time
BCK pulse duration, LOW
BCK pulse duration, HIGH
BCK rising edge to LRCK edge
LRCK edge to BCK rising edge
DATA setup time
70
30
30
10
10
10
10
ns
ns
ns
ns
ns
ns
ns
(BCY)
(BCL)
(BCH)
(BL)
(LB)
(DS)
DATA hold time
(DH)
—
LRCK clock data
50% 2 bit clocks
Figure 26. Timing of Audio Interface
16
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
(1) Standard Data Format (Right-Justified); L-Channel = HIGH, R-Channel = LOW
1/f
S
LRCK
R-Channel
L-Channel
BCK
Audio Data Word = 16-Bit
14 15 16
1
2
15 16
LSB
1
2
15 16
DATA
MSB
Audio Data Word = 20-Bit
18 19 20
1
2
19 20
LSB
1
2
19 20
23 24
DATA
MSB
Audio Data Word = 24-Bit
22 23 24
1
2
23 24
LSB
1
2
DATA
MSB
(2) Left-Justified Data Format; L-Channel = HIGH, R-Channel = LOW
1/f
S
LRCK
BCK
R-Channel
L-Channel
Audio Data Word = 24-Bit
DATA
1
2
23 24
LSB
1
2
23 24
1
2
MSB
2
(3) I S Data Format; L-Channel = LOW, R-Channel = HIGH
1/f
S
LRCK
L-Channel
R-Channel
BCK
Audio Data Word = 16-Bit
DATA
1
1
2
2
15 16
LSB
1
2
2
15 16
1
1
2
2
MSB
MSB
Audio Data Word = 24-Bit
DATA
23 24
LSB
1
23 24
Figure 27. Audio Data Input Formats
17
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
External Digital Filter Interface and Timing
The PCM1796 supports an external digital filter interface comprising a 3- or 4-wire synchronous serial port, which
allows the use of an external digital filter. External filters include the Texas Instruments’ DF1704 and DF1706, the
Pacific Microsonics PMD200, or a programmable digital signal processor.
In the external DF mode, LRCK (pin 4), BCK (pin 6) and DATA (pin 5) are defined as WDCK, the word clock; BCK,
the bit clock; and DATA, the monaural data. The external digital filter interface is selected by using the DFTH bit of
control register 20, which functions to bypass the internal digital filter of the PCM1796.
When the DFMS bit of control register 19 is set, the PCM1796 can process stereo data. In this case, ZEROL (pin 1)
and ZEROR (pin 2) are defined as L-channel data and R-channel data input, respectively.
Detailed information for the external digital filter interface mode is provided in the APPLICATION FOR EXTERNAL
DIGITAL FILTER INTERFACE section of this data sheet.
Direct Stream Digital (DSD) Format Interface and Timing
The PCM1796 supports the DSD format interface operation, which includes out-of-band noise filtering using an
internal analog FIR filter. For DSD operation, SCK (pin 7) is redefined as BCK, DATA (pin 5) as DATAL (left channel
audio data), and LRCK (pin 4) as DATAR (right channel audio data). BCK (pin 6) must be forced low in the DSD mode.
The DSD format interface is activated by setting the DSD bit of control register 20.
Detailed information for the DSD mode is provided in the APPLICATION FOR DSD FORMAT (DSD MODE)
INTERFACE section of this data sheet.
TDMCA Interface
The PCM1796 supports the time-division-multiplexed command and audio (TDMCA) data format to enable control
of and communication with a number of external devices over a single serial interface.
Detailed information for the TDMCA format is provided in the TDMCA INTERFACE FORMAT section of this data
sheet.
FUNCTION DESCRIPTIONS
Zero Detect
The PCM1796 has a zero-detect function. When the PCM1796 detects the zero conditions as shown in Table 2, the
PCM1796 sets ZEROL (pin 1) and ZEROR (pin 2) to HIGH.
Table 2. Zero Conditions
MODE
DETECTING CONDITION AND TIME
PCM
DATA is continuously LOW for 1024 LRCKs.
External DF Mode DATA is continuously LOW for 1024 WDCKs.
DZ0
There are an equal number of 1s and 0s in every 8 bits of DSD
input data for 23 ms.
DSD
DZ1
The input data is 1001 0110 continuously for 23 ms.
18
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
SERIAL CONTROL INTERFACE
2
The PCM1796 supports SPI and I C that sets mode control registers as shown in Table 4. This serial control interface
2
is selected by MSEL (pin 3), SPI is activated when MSEL is set to LOW, and I C is activated when MSEL is set to
HIGH.
SPI Interface
The SPI interface is a 4-wire synchronous serial port that operates asynchronously to the serial audio interface and
the system clock (SCK). The serial control interface is used to program and read the on-chip mode registers. The
control interface includes MDO (pin 13), MDI (pin 11), MC (pin 12), and MS (pin 10). MDO is the serial data output,
used to read back the values of the mode registers; MDI is the serial data input, used to program the mode registers;
MC is the serial bit clock, used to shift data in and out of the control port, and MS is the mode control enable, used
to enable the internal mode register access.
Register Read/Write Operation
All read/write operations for the serial control port use 16-bit data words. Figure 28 shows the control data word
format. The most significant bit is the read/write (R/W) bit. For write operations, the R/W bit must be set to 0. For
read operations, the R/W bit must be set to 1. There are seven bits, labeled IDX[6:0], that hold the register index (or
address) for the read and write operations. The least significant eight bits, D[7:0], contain the data to be written to,
or the data that was read from, the register specified by IDX[6:0].
Figure 29 shows the functional timing diagram for writing or reading the serial control port. MS is held at a logic 1
state until a register needs to be written or read. To start the register write or read cycle, MS is set to logic 0. Sixteen
clocks are then provided on MC, corresponding to the 16 bits of the control data word on MDI and readback data
on MDO. After the eighth clock cycle has completed, the data from the indexed-mode control register appears on
MDO during the read operation. After the sixteenth clock cycle has completed, the data is latched into the
indexed-mode control register during the write operation. To write or read subsequent data, MS must be set to 1 once.
LSB
D0
MSB
R/W IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0
D7
D6
D5
D4
D3
D2
D1
Register Index (or Address)
Register Data
Figure 28. Control Data Word Format for MDI
MS
MC
MDI
MDO
R/W A6 A5 A4 A3
A2 A1 A0 D7 D6 D5 D4
D3 D2 D1 D0
High Impedance
D7 D6 D5 D4
D3 D2 D1 D0
When Read Mode is Instructed
NOTE: Bit 15 is used for selection of write or read. Setting R/W = 0 indicates a write, while R/W = 1 indicates a read. Bits 14–8 are used for the register
address. Bits 7–0 are used for register data.
Figure 29. Serial Control Format
19
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
t
(MHH)
MS
1.4 V
t
t
(MCL)
(MSS)
t
t
(MSH)
(MCH)
MC
1.4 V
1.4 V
t
(MCY)
LSB
MDI
t
t
(MDS)
(MOS)
t
(MDH)
MDO
50% of V
DD
PARAMETER
MIN
100
40
MAX UNITS
t
t
t
t
t
t
t
t
t
MC pulse cycle time
MC low-level time
MC high-level time
MS high-level time
ns
ns
ns
ns
ns
ns
ns
ns
(MCY)
(MCL)
(MCH)
(MHH)
(MSS)
(MSH)
(MDH)
(MDS)
(MOS)
40
80
MS falling edge to MC rising edge
(1)
15
MS hold time
15
MDI hold time
15
MDI setup time
15
MC falling edge to MDO stable
30
ns
(1)
MC rising edge for LSB to MS rising edge
Figure 30. Control Interface Timing
20
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
2
I C INTERFACE
2
The PCM1796 supports the I C serial bus and the data transmission protocol for standard and fast mode as a slave
2
device. This protocol is explained in I C specification 2.0.
2
In I C mode, the control terminals are changed as follows.
TERMINAL NAME
TDMCA NAME
ADR0
PROPERTY
Input
DESCRIPTION
2
I C address 0
MS
MDI
MC
2
I C address 1
ADR1
Input
2
I C clock
SCL
Input
2
I C data
MDO
SDA
Input/output
Slave Address
MSB
1
LSB
R/W
0
0
1
1
ADR1
ADR0
The PCM1796 has 7 bits for its own slave address. The first five bits (MSBs) of the slave address are factory preset
to 10011. The next two bits of the address byte are the device select bits which can be user-defined by the ADR1
and ADR0 terminals. A maximum of four PCM1796s can be connected on the same bus at one time. Each PCM1796
responds when it receives its own slave address.
Packet Protocol
A master device must control packet protocol, which consists of start condition, slave address, read/write bit, data
if write or acknowledge if read, and stop condition. The PCM1796 supports only slave receivers and slave
transmitters.
SDA
SCL
St
1−7
8
9
1−8
9
1−8
9
9
Sp
Slave Address R/W
ACK
DATA
ACK
DATA
ACK
ACK
R/W: Read Operation if 1; Otherwise, Write Operation
ACK: Acknowledgement of a Byte if 0
NACK: Not Acknowledgement if 1
DATA: 8 Bits (Byte)
Start
Condition
Stop
Condition
Write Operation
Transmitter
Data Type
M
M
M
S
M
S
M
S
S
M
St
Slave Address
W
ACK
DATA
ACK
DATA
ACK
ACK
Sp
Read Operation
Transmitter
Data Type
M
M
M
S
S
M
S
M
M
M
St
Slave Address
R
ACK
DATA
ACK
DATA
ACK
NACK
Sp
M: Master Device
S: Slave Device
St: Start Condition
Sp: Stop Condition
W: Write
R: Read
ACK: Acknowledge
NACK: Not Acknowledge
2
Figure 31. Basic I C Framework
21
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Write Register
A master can write to any PCM1796 registers using single or multiple accesses. The master sends a PCM1796 slave
address with a write bit, a register address, and the data. If multiple access is required, the address is that of the
starting register, followed by the data to be transferred. When the data are received properly, the index register is
incremented by 1 automatically. When the index register reaches 0x7F, the next value is 0x00. When undefined
registers are accessed, the PCM1796 does not send an acknowledgement. Figure 32 is a diagram of the write
operation.
Transmitter
M
M
M
M
S
M
S
M
S
M
S
S
Data Type St
Sp
Slave Address
W
ACK
ACK
ACK
ACK
ACK
Reg Address
Write Data 1
Write Data 2
M: Master Device
S: Slave Device
St: Start Condition
Sp: Stop Condition ACK: Acknowledge W: Write
Figure 32. Write Operation
Read Register
A master can read the PCM1796 register. The value of the register address is stored in an indirect index register in
advance. The master sends a PCM1796 slave address with a read bit after storing the register address. Then the
PCM1796 transfers the data which the index register points to. When the data are transferred during a multiple
access, the index register is incremented by 1 automatically. (When first going into read mode immediately following
a write, the index register is not incremented. The master can read the register that was previously written.) When
the index register reaches 0x7F, the next value is 0x00. The PCM1796 outputs some data when the index register
is 0x10 to 0x1F, even if it is not defined in Table 4. Figure 33 is a diagram of the read operation.
Transmitter
M
M
M
M
S
M
S
M
M
M
S
S
M
M
Data Type St
Sp
Slave Address
W
ACK
ACK Sr
R
ACK
ACK
NACK
Reg Address
Slave Address
Data
M: Master Device
St: Start Condition
W: Write
S: Slave Device
Sr: Repeated Start Condition Sp: Stop Condition
R: Read
ACK: Acknowledge
NACK: Not Acknowledge
Figure 33. Read Operation
22
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Noise Suppression
The PCM1796 incorporates noise suppression using the system clock (SCK). However, there must be no more than
two noise spikes in 600 ns. The noise suppression works for SCK frequencies between 8 MHz and 40 MHz in fast
mode. However, it works incorrectly in the following conditions.
Case 1:
1.
2.
t
t
> 120 ns (t
: period of SCK)
(SCK)
(SCK)
+ t
< t
(D–HD)
× 5
(HI)
(SCK)
3. Spike noise exists on the first half of the SCL HIGH pulse.
4. Spike noise exists on the SDA HIGH pulse just before SDA goes LOW.
SCL
Noise
SDA
When these conditions occur at the same time, the data is recognized as LOW.
Case 2:
1.
2.
t
t
> 120 ns
(SCK)
or t
< t
× 5
(SCK)
(S–HD)
(RS–HD)
3. Spike noise exists on both SCL and SDA during the hold time.
SCL
Noise
SDA
When these conditions occur at the same time, the PCM1796 fails to detect a start condition.
Case 3:
1.
2.
t
t
< 50 ns
(SCK)
(SP)
> t
(SCK)
3. Spike noise exists on SCL just after SCL goes LOW.
4. Spike noise exists on SDA just before SCL goes LOW.
SCL
SDA
Noise
When these conditions occur at the same time, the PCM1796 erroneously detects a start or stop condition.
23
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
TIMING DIAGRAM
Start
Repeated Start
(D-HD)
Stop
t
t
(SDA-F)
t
t
t
t
(P-SU)
(BUF)
(D-SU)
(SDA-R)
SDA
t
t
t
(SP)
(SCL-R)
(RS-HD)
t
(LOW)
SCL
t
t
t
(RS-SU)
(S-HD)
(HI)
t
(SCL-F)
TIMING CHARACTERISTICS
PARAMETER
CONDITIONS
Standard
Fast
MIN MAX
100
400
4.7
UNIT
f
t
t
t
t
SCL clock frequency
kHz
(SCL)
(BUF)
(LOW)
(HI)
Standard
Fast
Bus free time between stop and start conditions
Low period of the SCL clock
High period of the SCL clock
Setup time for (repeated) start condition
Hold time for (repeated) start condition
Data setup time
µs
µs
1.3
Standard
Fast
4.7
1.3
Standard
Fast
4
µs
ns
µs
ns
µs
ns
600
4.7
Standard
Fast
(RS-SU)
600
4
t
t
Standard
Fast
(S-HD)
600
250
100
(RS-HD)
Standard
Fast
t
t
t
t
t
t
t
t
ns
ns
ns
ns
ns
ns
ns
(D-SU)
Standard
Fast
0
0
900
900
Data hold time
(D-HD)
Standard
Fast
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
20 + 0.1 C
1000
300
B
B
B
B
B
B
B
B
B
Rise time of SCL signal
(SCL-R)
(SCL-R1)
(SCL-F)
(SDA-R)
(SDA-F)
(P-SU)
Standard
Fast
1000
300
Rise time of SCL signal after a repeated start condition and after an
acknowledge bit
Standard
Fast
1000
300
Fall time of SCL signal
Rise time of SDA signal
Fall time of SDA signal
Setup time for stop condition
Standard
Fast
1000
300
Standard
Fast
1000
300
B
4
Standard
Fast
µs
ns
pF
ns
V
600
C
Capacitive load for SDA and SCL line
Pulse duration of suppressed spike
400
50
(B)
t
Fast
(SP)
V
NH
Noise margin at high level for each connected device (including hysteresis)
0.2 V
DD
2
Figure 34. Timing Definition on the I C Bus
24
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
MODE CONTROL REGISTERS
User-Programmable Mode Controls
The PCM1796 includes a number of user-programmable functions which are accessed via mode control registers.
The registers are programmed using the serial control interface, which is previously discussed in the SPI Interface
2
and I C INTERFACE sections of this data sheet. Table 3 lists the available mode-control functions, along with their
default reset conditions and associated register index.
Table 3. User-Programmable Function Controls
DF
BYPASS
FUNCTION
Digital attenuation control
DEFAULT
REGISTER
BIT
PCM
DSD
0 dB
Attenuation disabled
Register 16 ATL[7:0] (for L-ch)
Register 17 ATR[7:0] (for R-ch)
yes
0 dB to –120 dB and mute, 0.5 dB step
Attenuation load control
Disabled, enabled
Register 18 ATLD
yes
yes
2
Input audio data format selection
24-bit I S format
Register 18 FMT[2:0]
yes
16-, 20-, 24-bit standard (right-justified) format
24-bit MSB-first left-justified format
2
16-/24-bit I S format
(1)
yes
Sampling rate selection for de-emphasis
Disabled,44.1 kHz, 48 kHz, 32 kHz
De-emphasis disabled
De-emphasis disabled
Mute disabled
Register 18 DMF[1:0]
Register 18 DME
Register 18 MUTE
Register 19 REV
yes
yes
yes
yes
yes
yes
De-emphasis control
Disabled, enabled
Soft mute control
Soft mute disabled, enabled
Output phase reversal
Normal, reverse
Normal
yes
yes
Attenuation speed selection
×1 f
Register 19 ATS[1:0]
S
×1f , ×(1/2)f , ×(1/4)f , ×(1/8)f
S
S
S
S
DAC operation control
Enabled, disabled
DAC operation enabled Register 19 OPE
yes
yes
yes
Stereo DF bypass mode select
Monaural, stereo
Monaural
Register 19 DFMS
Register 19 FLT
Digital filter rolloff selection
Sharp rolloff, slow rolloff
Sharp rolloff
Disabled
yes
yes
yes
yes
yes
yes
yes
yes
yes
Infinite zero mute control
Disabled, enabled
Register 19 INZD
Register 20 SRST
Register 20 DSD
Register 20 DFTH
Register 20 MONO
Register 20 CHSL
Register 20 OS[1:0]
yes
yes
System reset control
Reset operation , normal operation
Normal operation
Disabled
yes
yes
DSD interface mode control
DSD enabled, disabled
Digital-filter bypass control
DF enabled, DF bypass
DF enabled
Stereo
yes
yes
yes
yes
yes
Monaural mode selection
Stereo, monaural
yes
yes
Channel selection for monaural mode data
L-channel, R-channel
L-channel
(2)
yes
Delta-sigma oversampling rate selection
×64 f
S
×64 f , ×128 f , ×32 f
S
S
S
PCM zero output enable
Enabled
Disabled
Register 21 PCMZ
Register 21 DZ[1:0]
DSD zero output enable
yes
yes
FUNCTION AVAILABLE ONLY FOR READ
Zero detection flag
Not zero, zero detected
Not zero = 0
Zero detected = 1
Register 22 ZFGL (for L-ch)
ZFGR (for R-ch)
yes
yes
yes
Device ID (at TDMCA)
–
Register 23 ID[4:0]
(1)
(2)
When in DSD mode, DMF[1:0] is defined as DSD filter (analog FIR) performance selection.
When in DSD mode, OS[1:0] is defined as DSD filter (analog FIR) operation rate selection.
25
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Register Map
The mode control register map is shown in Table 4. Registers 16–21 include an R/W bit, which determines whether
a register read (R/W = 1) or write (R/W = 0) operation is performed. Registers 22 and 23 are read-only.
Table 4. Mode Control Register Map
B15
Register 16 R/W
Register 17 R/W
Register 18 R/W
Register 19 R/W
Register 20 R/W
Register 21 R/W
B14
0
B13
0
B12
1
B11
0
B10 B9 B8
B7
B6
B5
B4
B3
B2
B1
B0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
ATL7 ATL6 ATL5 ATL4
ATL3
ATL2
ATL1
ATL0
0
0
1
0
ATR7 ATR6 ATR5 ATR4 ATR3
ATLD FMT2 FMT1 FMT0 DMF1 DMF0 DME MUTE
ATR2 ATR1 ATR0
0
0
1
0
0
0
1
0
REV ATS1 ATS0 OPE
RSV
DFMS
FLT
OS1
DZ0
INZD
OS0
0
0
1
0
RSV SRST DSD DFTH MONO CHSL
0
0
1
0
RSV
RSV
RSV
RSV
RSV
RSV
RSV
RSV
RSV
RSV
RSV
ID4
RSV
RSV
ID3
DZ1
RSV
ID2
PCMZ
Register 22
Register 23
R
R
0
0
1
0
ZFGR ZFGL
0
0
1
0
ID1
ID0
Register Definitions
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 16
R/W
0
0
1
0
0
0
0
ATL7 ATL6 ATL5 ATL4 ATL3 ATL2 ATL1 ATL0
Register 17 R/W
0
0
1
0
0
0
1
ATR7 ATR6 ATR5 ATR4 ATR3 ATR2 ATR1 ATR0
R/W: Read/Write Mode Select
When R/W = 0, a write operation is performed.
When R/W = 1, a read operation is performed.
Default value: 0
ATx[7:0]: Digital Attenuation Level Setting
These bits are available for read and write.
Default value: 1111 1111b
Each DAC output has a digital attenuator associated with it. The attenuator can be set from 0 dB to –120 dB, in 0.5-dB
steps. Alternatively, the attenuator can be set to infinite attenuation (or mute).
The attenuation data for each channel can be set individually. However, the data load control (the ATLD bit of control
register 18) is common to both attenuators. ATLD must be set to 1 in order to change an attenuator setting. The
attenuation level can be set using the following formula:
Attenuation level (dB) = 0.5 dB • (ATx[7:0]
– 255)
DEC
where ATx[7:0]
= 0 through 255
DEC
For ATx[7:0]
levels for various settings:
= 0 through 14, the attenuator is set to infinite attenuation. The following table shows attenuation
DEC
ATx[7:0]
1111 1111b
1111 1110b
1111 1101b
L
Decimal Value
Attenuation Level Setting
255
254
253
L
0 dB, no attenuation (default)
–0.5 dB
–1.0 dB
L
0001 0000b
0000 1111b
0000 1110b
L
16
15
14
L
–119.5 dB
–120.0 dB
Mute
L
0000 0000b
0
Mute
26
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
B15 B14 B13 B12 B11 B10
R/W
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 18
0
0
1
0
0
1
0
ATLD FMT2 FMT1 FMT0 DMF1 DMF0 DME MUTE
R/W: Read/Write Mode Select
When R/W = 0, a write operation is performed.
When R/W = 1, a read operation is performed.
Default value: 0
ATLD: Attenuation Load Control
This bit is available for read and write.
Default value: 0
ATLD = 0
ATLD = 1
Attenuation control disabled (default)
Attenuation control enabled
The ATLD bit is used to enable loading of the attenuation data contained in registers 16 and 17. When ATLD = 0,
the attenuation settings remain at the previously programmed levels, ignoring new data loaded from registers 16 and
17. When ATLD = 1, attenuation data written to registers 16 and 17 is loaded normally.
FMT[2:0]: Audio Interface Data Format
These bits are available for read and write.
Default value: 101
FMT[2:0]
000
Audio Data Format Selection
16-bit standard format, right-justified data
20-bit standard format, right-justified data
24-bit standard format, right-justified data
24-bit MSB-first, left-justified format data
001
010
011
2
100
16-bit I S format data
2
101
24-bit I S format data (default)
110
Reserved
Reserved
111
The FMT[2:0] bits are used to select the data format for the serial audio interface.
For the external digital filter interface mode (DFTH mode), this register is operated as shown in the APPLICATION
FOR EXTERNAL DIGITAL FILTER INTERFACE section of this data sheet.
DMF[1:0]: Sampling Frequency Selection for the De-Emphasis Function
These bits are available for read and write.
Default value: 00
DMF[1:0]
De-Emphasis Sampling Frequency Selection
00
01
10
11
Disabled (default)
48 kHz
44.1 kHz
32 kHz
The DMF[1:0] bits are used to select the sampling frequency used by the digital de-emphasis function when it is
enabled by setting the DME bit. The de-emphasis curves are shown in the TYPICAL PERFORMANCE CURVES
section of this data sheet.
For the DSD mode, analog FIR filter performance can be selected using this register. A register map and filter
response plots are shown in the APPLICATION FOR DSD FORMAT (DSD MODE) INTERFACE section of this data
sheet.
27
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
DME: Digital De-Emphasis Control
This bit is available for read and write.
Default value: 0
DME = 0
DME = 1
De-emphasis disabled (default)
De-emphasis enabled
The DME bit is used to enable or disable the de-emphasis function for both channels.
MUTE: Soft Mute Control
This bit is available for read and write.
Default value: 0
MUTE = 0
MUTE = 1
Soft mute disabled (default)
Soft mute enabled
The MUTE bit is used to enable or disable the soft mute function for both channels.
Soft mute is operated as a 256-step attenuator. The speed for each step to –∞ dB (mute) is determined by the
attenuation rate selected in the ATS register.
B15 B14 B13 B12 B11 B10
R/W
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 19
0
0
1
0
0
1
1
REV ATS1 ATS0 OPE
RSV DFMS
FLT
INZD
R/W: Read/Write Mode Select
When R/W = 0, a write operation is performed.
When R/W = 1, a read operation is performed.
Default value: 0
REV: Output Phase Reversal
This bit is available for read and write.
Default value: 0
REV = 0
REV = 1
Normal output (default)
Inverted output
The REV bit is used to invert the output phase for both channels.
ATS[1:0]: Attenuation Rate Select
These bits are available for read and write.
Default value: 00
ATS[1:0]
Attenuation Rate Selection
Every LRCK (default)
LRCK/2
00
01
10
11
LRCK/4
LRCK/8
The ATS[1:0] bits are used to select the rate at which the attenuator is decremented/incremented during level
transitions.
28
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
OPE: DAC Operation Control
This bit is available for read and write.
Default value: 0
OPE = 0
OPE = 1
DAC operation enabled (default)
DAC operation disabled
The OPE bit is used to enable or disable the analog output for both channels. Disabling the analog outputs forces
them to the bipolar zero level (BPZ) even if audio data is present on the input.
DFMS: Stereo DF Bypass Mode Select
This bit is available for read and write.
Default value: 0
DFMS = 0
DFMS = 1
Monaural (default)
Stereo input enabled
The DFMS bit is used to enable stereo operation in DF bypass mode. In the DF bypass mode, when DFMS is set
to 0, the pin for the input data is DATA (pin 5) only, therefore the PCM1796 operates as a monaural DAC. When DFMS
is set to 1, the PCM1796 can operate as a stereo DAC with inputs of L-channel and R-channel data on ZEROL (pin 1)
and ZEROR (pin 2), respectively.
FLT: Digital Filter Rolloff Control
This bit is available for read and write.
Default value: 0
FLT = 0
FLT = 1
Sharp rolloff (default)
Slow rolloff
The FLT bit is used to select the digital filter rolloff characteristic. The filter responses for these selections are shown
in the TYPICAL PERFORMANCE CURVES section of this data sheet.
INZD: Infinite Zero Detect Mute Control
This bit is available for read and write.
Default value: 0
INZD = 0
INZD = 1
Infinite zero detect mute disabled (default)
Infinite zero detect mute enabled
The INZD bit is used to enable or disable the zero detect mute function. Setting INZD to 1 forces muted analog outputs
to hold a bipolar zero level when the PCM1796 detects a zero condition in both channels. The infinite zero detect
mute function is not available in the DSD mode.
B15 B14 B13 B12 B11 B10
R/W
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 20
0
0
1
0
1
0
0
RSV SRST DSD DFTH MONO CHSL OS1
OS0
R/W: Read/Write Mode Select
When R/W = 0, a write operation is performed.
When R/W = 1, a read operation is performed.
Default value: 0
29
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
SRST: System Reset Control
This bit is available for write only.
Default value: 0
SRST = 0
SRST = 1
Normal operation (default)
System reset operation (generate one reset pulse)
The SRST bit is used to reset the PCM1796 to the initial system condition.
DSD: DSD Interface Mode Control
This bit is available for read and write.
Default value: 0
DSD = 0
DSD = 1
DSD interface mode disabled (default)
DSD interface mode enabled
The DSD bit is used to enable or disable the DSD interface mode.
DFTH: Digital Filter Bypass (or Through Mode) Control
This bit is available for read and write.
Default value: 0
DFTH = 0
DFTH = 1
Digital filter enabled (default)
Digital filter bypassed for external digital filter
The DFTH bit is used to enable or disable the external digital filter interface mode.
MONO: Monaural Mode Selection
This bit is available for read and write.
Default value: 0
MONO = 0
MONO = 1
Stereo mode (default)
Monaural mode
The MONO function is used to change operation mode from the normal stereo mode to the monaural mode. When
the monaural mode is selected, both DACs operate in a balanced mode for one channel of audio input data. Channel
selection is available for L-channel or R-channel data, determined by the CHSL bit as described immediately
following.
CHSL: Channel Selection for Monaural Mode
This bit is available for read and write.
Default value: 0
CHSL = 0
CHSL = 1
L-channel selected (default)
R-channel selected
This bit is available when MONO = 1.
The CHSL bit selects L-channel or R-channel data to be used in monaural mode.
30
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
OS[1:0]: Delta-Sigma Oversampling Rate Selection
These bits are available for read and write.
Default value: 00
OS[1:0]
00
Operation Speed Select
64 times f (default)
S
01
32 times f
S
10
128 times f
Reserved
S
11
The OS bits are used to change the oversampling rate of delta-sigma modulation. Use of this function enables the
designer to stabilize the conditions at the post low-pass filter for different sampling rates. As an application example,
programming to set 128 times in 44.1-kHz operation, 64 times in 96-kHz operation, and 32 times in 192-kHz operation
allows the use of only a single type (cutoff frequency) of post low-pass filter. The 128 f oversampling rate is not
S
available at sampling rates above 100 kHz. If the 128-f oversampling rate is selected, a system clock of more than
S
256 f is required.
S
In DSD mode, these bits are used to select the speed of the bit clock for DSD data coming into the analog FIR filter.
B15 B14 B13 B12 B11 B10
R/W
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 21
0
0
1
0
1
0
1
RSV
RSV
RSV
RSV
RSV
DZ1
DZ0 PCMZ
R/W: Read/Write Mode Select
When R/W = 0, a write operation is performed.
When R/W = 1, a read operation is performed.
Default value: 0
DZ[1:0]: DSD Zero Output Enable
These bits are available for read and write.
Default value: 00
DZ[1:0]
00
Zero Output Enable
Disabled (default)
Even pattern detect
96h pattern detect
01
1x
The DZ bits are used to enable or disable the output zero flags, and to select the zero pattern in the DSD mode.
PCMZ: PCM Zero Output Enable
These bits are available for read and write.
Default value: 1
PCMZ = 0
PCMZ = 1
PCM zero output disabled
PCM zero output enabled (default)
The PCMZ bit is used to enable or disable the output zero flags in the PCM mode and the external DF mode.
B15 B14 B13 B12 B11 B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 22
R
0
0
1
0
1
1
0
RSV
RSV
RSV
RSV
RSV
RSV ZFGR ZFGL
R: Read Mode Select
Value is always 1, specifying the readback mode.
31
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ZFGx: Zero-Detection Flag
Where x = L or R, corresponding to the DAC output channel. These bits are available only for readback.
Default value: 00
ZFGx = 0
ZFGx = 1
Not zero
Zero detected
These bits show zero conditions. Their status is the same as that of the zero flags at ZEROL (pin 1) and ZEROR
(pin 2). See Zero Detect in the FUNCTION DESCRIPTIONS section.
B15 B14 B13 B12 B11 B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 23
R
0
0
1
0
1
1
1
RSV
RSV
RSV
ID4
ID3
ID2
ID1
ID0
R: Read Mode Select
Value is always 1, specifying the readback mode.
ID[4:0]: Device ID
The ID[4:0] bits hold a device ID in the TDMCA mode.
32
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
APPLICATION INFORMATION
TYPICAL CONNECTION DIAGRAM IN PCM MODE
C
f
5 V
R
R
f
0.1 µF
ZEROL
ZEROR
MSEL
LRCK
DATA
BCK
V
2L
1
2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
10 µF
CC
–
+
AGND3L
Differential
to
Single
Converter
With
Low-Pass
Filter
I L–
OUT
3
C
f
V
OUT
L-Channel
I
L+
4
OUT
f
PCM
Audio
Data
5 V
AGND2
5
–
+
V
1
CC
6
Source
10 µF
SCK
V L
COM
7
+
C
f
PCM1796
DGND
V
COM
R
8
R
R
0.1 µF
47 µF
10 kΩ
f
V
DD
I
REF
9
–
+
MS
AGND1
10
11
12
13
14
Differential
to
Single
Converter
With
Low-Pass
Filter
MDI
MC
I
R–
R+
C
OUT
f
V
OUT
R-Channel
Controller
I
OUT
f
0.1 µF
5 V
AGND3R
MDO
RST
–
+
V
CC
2R
10 µF
3.3 V
+
10 µF
Figure 35. Typical Application Circuit for Standard PCM Audio Operation
APPLICATION CIRCUIT
The design of the application circuit is very important in order to actually realize the high S/N ratio of which the
PCM1796 is capable. This is because noise and distortion that are generated in an application circuit are not
negligible.
In the third-order LPF circuit of Figure 36, the output level is 2.1 V rms and 123 dB S/N is achieved.
Figure 37 shows a circuit for the DSD mode, which is a fourth-order LPF in order to reduce the out-of-band noise.
I/V Section
The current of the PCM1796 on each of the output pins (I
L+, I
L–, I
R+, I
R–) is 4 mA p-p at 0 dB (full
OUT
OUT
OUT
OUT
scale). The voltage output level of the I/V converter (Vi) is given by following equation:
Vi = 4 mA p-p × R (R : feedback resistance of I/V converter)
f
f
An NE5534 operational amplifier is recommended for the I/V circuit to obtain the specified performance. Dynamic
performance such as the gain bandwidth, settling time, and slew rate of the operational amplifier affects the audio
dynamic performance of the I/V section.
33
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Differential Section
The PCM1796 voltage outputs are followed by differential amplifier stages, which sum the differential signals for each
channel, creating a single-ended I/V op-amp output. In addition, the differential amplifiers provide a low-pass filter
function.
The operational amplifier recommended for the differential circuit is the low-noise type.
C
1
2700 pF
R
1
820 Ω
V
CC
V
CC
C
3
C
11
0.1 µF
8200 pF
R
200 Ω
5
C
15
0.1 µF
C
22 pF
17
C
22 pF
19
7
5
R
220 Ω
R
7
7
2
3
8
6
3
–
+
I –
OUT
5
180 Ω
R
100 Ω
2
3
8
6
9
–
+
C
5
U
1
27000 pF
NE5534
U
4
3
NE5534
4
R
4
R
8
180 Ω
C
12
0.1 µF
220 Ω
R
6
200 Ω
C
16
0.1 µF
C
4
V
EE
8200 pF
V
EE
C
2
2700 pF
R
2
820 Ω
V
CC
C
13
0.1 µF
C
22 pF
18
7
5
2
3
8
6
–
+
I +
OUT
U
2
NE5534
4
V
V
= 15 V
= –15 V
= 50 kHz
CC
EE
C
14
0.1 µF
f
c
V
EE
Figure 36. Measurement Circuit for PCM
34
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
C
1
2200 pF
R
1
820 Ω
V
CC
V
CC
C
5
C
11
0.1 µF
8200 pF
R
150 Ω
5
C
15
0.1 µF
C
22 pF
17
C
22 pF
19
7
5
R
91 Ω
R
75 Ω
R
120 Ω
7
2
3
8
6
3
8
10
–
+
I –
OUT
5
R
100 Ω
2
3
8
6
7
–
+
C
3
C
4
U
1
22000 pF
27000 pF
R
11
NE5534
U
4
3
NE5534
4
R
4
R
9
75 Ω
C
12
0.1 µF
91 Ω
120 Ω
R
6
150 Ω
C
16
0.1 µF
C
6
V
EE
8200 pF
V
EE
C
2
2200 pF
R
2
820 Ω
V
CC
C
13
0.1 µF
C
22 pF
18
7
5
2
3
8
6
–
+
I +
OUT
U
2
NE5534
4
V
V
= 15 V
= –15 V
= 50 kHz
CC
EE
C
14
0.1 µF
f
c
V
EE
Figure 37. Measurement Circuit for DSD
35
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
I
L– (Pin 26)
L+ (Pin 25)
I
I
–
+
OUT
OUT
OUT+
Figure 36
Circuit
I
OUT
OUT
3
2
1
I
R– (Pin 18)
R+ (Pin 17)
I
I
–
+
OUT
OUT
OUT–
Figure 36
Circuit
Balanced Out
I
OUT
OUT
Figure 38. Measurement Circuit for Monaural Mode
36
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
APPLICATION FOR EXTERNAL DIGITAL FILTER INTERFACE
DFMS = 0
External Filter Device
PCM1796
ZEROL
ZEROR
MSEL
LRCK
DATA
BCK
1
2
3
WDCK (Word Clock)
4
5
6
7
DATA
BCK
SCK
SCK
DFMS = 1
External Filter Device
PCM1796
DATA_L
ZEROL
ZEROR
MSEL
LRCK
DATA
BCK
1
DATA_R
2
3
4
5
6
7
WDCK (Word Clock)
BCK
SCK
SCK
Figure 39. Connection Diagram for External DIgital Filter (Internal DF Bypass Mode) Application
37
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Application for Interfacing With an External Digital Filter
For some applications, it may be desirable to use an external digital filter to perform the interpolation function, as it
can provide improved stop-band attenuation when compared to the internal digital filter of the PCM1796.
The PCM1796 supports several external digital filters, including:
D
D
D
Texas Instruments DF1704 and DF1706
Pacific Microsonics PMD200 HDCD filter/decoder IC
Programmable digital signal processors
The external digital filter application mode is accessed by programming the following bits in the corresponding control
register:
D
DFTH = 1 (register 20)
The pins used to provide the serial interface for the external digital filter are shown in the connection diagram of
Figure 39. The word clock (WDCK) signal must be operated at 8× or 4× the desired sampling frequency, f .
S
Pin Assignment When Using the External Digital Filter Interface
D
D
D
D
D
LRCK (pin 4): WDCK as word clock input
BCK (pin 6): Bit clock for audio data
DATA (pin 5): Monaural audio data input when the DFMS bit is not set to 1
ZEROL (pin 1): DATAL as L-channel audio data input when the DFMS bit is set to 1
ZEROR (pin 2): DATAR as R-channel audio data input when the DFMS bit is set to 1
38
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Audio Format
The PCM1796 in the external digital filter interface mode supports right-justified audio formats including 16-bit, 20-bit,
and 24-bit audio data, as shown in Figure 40. The audio format is selected by the FMT[2:0] bits of control register18.
1/4 f or 1/8 f
S
S
WDCK
BCK
Audio Data Word = 16-Bit
DATA,
DATAL, DATAR
15 16
1
2
3
4
8
5
9
6
7
8
9
10 11 12 13 14 15 16
LSB
MSB
Audio Data Word = 20-Bit
DATA,
19 20
1
5
2
6
3
4
8
5
9
6
7
10 11 12 13 14 15 16 17 18 19 20
LSB
DATAL, DATAR
MSB
Audio Data Word = 24-Bit
DATA,
23 24
1
2
3
4
7
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
LSB
DATAL, DATAR
MSB
Figure 40. Audio Data Input Format for External Digital Filter (Internal DF Bypass Mode) Application
System Clock (SCK) and Interface Timing
The PCM1796 in an application using an external digital filter requires the synchronization of WDCK and the system
clock. The system clock is phase-free with respect to WDCK. Interface timing among WDCK, BCK, DATA, DATAL,
and DATAR is shown in Figure 41.
1.4 V
1.4 V
1.4 V
WDCK
BCK
t
t
t
(LB)
(BCH)
(BCL)
t
t
(BCY)
(BL)
DATA
DATAL
DATAR
t
t
(DS)
(DH)
PARAMETER
MIN
20
7
MAX UNITS
t
t
t
t
t
t
t
BCK pulse cycle time
ns
ns
ns
ns
ns
ns
ns
(BCY)
(BCL)
(BCH)
(BL)
BCK pulse duration, LOW
BCK pulse duration, HIGH
7
BCK rising edge to WDCK falling edge
WDCK falling edge to BCK rising edge
DATA, DATAL, DATAR setup time
DATA, DATAL, DATAR hold time
5
5
(LB)
5
(DS)
5
(DH)
Figure 41. Audio Interface Timing for External Digital Filter (Internal DF Bypass Mode) Application
39
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
FUNCTIONS AVAILABLE IN THE EXTERNAL DIGITAL FILTER MODE
The external digital filter mode is selected by setting DSD = 0 (register 20, B5) and DFTH = 1 (register 20. B4).
The external digital filter mode allows access to the majority of the PCM1796 mode control functions.
The following table shows the register mapping available when the external digital filter mode is selected, along with
descriptions of functions which are modified when using this mode selection.
B15 B14 B13 B12 B11 B10
B9
0
B8
0
B7
B6
–
B5
–
B4
–
B3
–
B2
B1
–
B0
–
Register 16 R/W
Register 17 R/W
Register 18 R/W
Register 19 R/W
Register 20 R/W
Register 21 R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
–
–
–
0
1
–
–
–
–
–
–
–
–
1
0
–
FMT2 FMT1 FMT0
–
–
–
1
1
REV
–
–
SRST
–
–
0
–
–
OPE
–
DFMS
–
INZD
OS0
PCMZ
0
0
1
–
–
MONO CHSL OS1
0
1
–
–
–
–
–
–
Register 22
R
1
0
–
–
ZFGR ZFGL
NOTE: –: Function is disabled. No operation even if data bit is set
FMT[2:0]: Audio Data Format Selection
Default value: 000
FMT[2:0]
000
Audio Data Format Select
16-bit right-justified format (default)
20-bit right-justified format
24-bit right-justified format
N/A
001
010
Other
OS[1:0]: Delta-Sigma Modulator Oversampling Rate Selection
Default value: 00
OS[1:0]
00
Operation Speed Select
8 times WDCK (default)
4 times WDCK
01
10
16 times WDCK
11
Reserved
The effective oversampling rate is determined by the oversampling performed by both the external digital filter and
the delta-sigma modulator. For example, if the external digital filter is 8× oversampling, and the user selects
OS[1:0] = 00, then the delta-sigma modulator oversamples by 8×, resulting in an effective oversampling rate of 64×.
The 16× WDCK oversampling rate is not available above a 100-kHz sampling rate. If the oversampling rate selected
is 16× WDCK, the system clock frequency must be over 256 f .
S
40
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
APPLICATION FOR DSD FORMAT (DSD MODE) INTERFACE
DSD Decoder
PCM1796
ZEROL
ZEROR
MSEL
LRCK
DATA
BCK
1
2
3
DATA_R
DATA_L
4
5
6
7
Bit Clock
SCK
Figure 42. Connection Diagram in DSD Mode
Feature
This mode is used for interfacing directly to a DSD decoder, which is found in Super Audio CDt (SACD) applications.
The DSD mode is accessed by programming the following bit in the corresponding control register.
DSD = 1 (register 20)
The DSD mode provides a low-pass filtering function. The filtering is provided using an analog FIR filter structure.
Four FIR responses are available, and are selected by the DMF[1:0] bits of control register 18.
The DSD bit must be set before inputting DSD data; otherwise, the PCM1796 erroneously detects the TDMCA mode,
and commands are not accepted through the serial control interface.
Pin Assignment When Using DSD Format Interface
Several pins are redefined for DSD mode operation. These include:
D
D
D
D
DATA (pin 5): DSDL as L-channel DSD data input
LRCK (pin 4): DSDR as R-channel DSD data input
SCK (pin 7): DBCK as bit clock for DSD data
BCK (pin 6): Set LOW (N/A)
Super Audio CD is a trademark of Sony Kabushiki Kaisha TA Sony Corporation, Japan.
41
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Requirements for System Clock
For operation in the DSD mode, the bit clock (DBCK) is required on pin 7 of the PCM1796. The frequency of the bit
clock can be N times the sampling frequency. Generally, N is 64 in DSD applications.
The interface timing between the bit clock and DSDL and DSDR is required to meet the setup and hold time
specifications shown in Figure 44.
t = 1/(64 × 44.1 kHz)
DBCK
DSDL
DSDR
D0
D1
D2
D3
D4
Figure 43. Normal Data Output Form From DSD Decoder
t
t
(BCL)
(BCH)
1.4 V
1.4 V
DBCK
t
(BCY)
DSDL
DSDR
t
t
(DH)
(DS)
PARAMETER
MIN MAX UNITS
(1)
t
DBCK pulse cycle time
DBCK high-level time
DBCK low-level time
85
ns
ns
ns
ns
ns
(BCY)
t
30
30
10
10
(BCH)
t
(BCL)
(DS)
(DH)
t
t
DSDL, DSDR setup time
DSDL, DSDR hold time
(1)
2.8224 MHz × 4. (2.8224 MHz = 64 × 44.1 kHz. This value is
specified as a sampling rate of DSD.)
Figure 44. Timing for DSD Audio Interface
42
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ANALOG FIR FILTER PERFORMANCE IN DSD MODE
GAIN
vs
GAIN
vs
FREQUENCY
FREQUENCY
0
−1
−2
−3
−4
−5
−6
0
−10
−20
−30
−40
−50
−60
f
= 185 kHz
c
(1)
Gain = –6.6 dB
0
50
100
150
200
0
500
1000
1500
f – Frequency – kHz
f – Frequency – kHz
Figure 45. DSD Filter-1, Low BW
Figure 46. DSD Filter-1, High BW
GAIN
vs
GAIN
vs
FREQUENCY
FREQUENCY
0
−1
−2
−3
−4
−5
−6
0
−10
−20
−30
−40
−50
−60
f
= 90 kHz
c
(1)
Gain = 0.3 dB
0
50
100
150
200
0
500
1000
1500
f – Frequency – kHz
f – Frequency – kHz
Figure 47. DSD Filter-2, Low BW
Figure 48. DSD Filter-2, High BW
(1)
This gain is in comparison to PCM 0 dB, when the DSD input signal efficiency is 50%.
All specifications at DBCK = 2.8224 MHz (44.1 kHz × 64 f ), and 50% modulation DSD data input, unless otherwise noted.
S
43
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ANALOG FIR FILTER PERFORMANCE IN DSD MODE (CONTINUED)
GAIN
vs
GAIN
vs
FREQUENCY
FREQUENCY
0
−1
−2
−3
−4
−5
−6
0
−10
−20
−30
−40
−50
−60
f
= 85 kHz
c
(1)
Gain = –1.5 dB
0
50
100
150
200
0
500
1000
1500
f – Frequency – kHz
f – Frequency – kHz
Figure 49. DSD Filter-3, Low BW
Figure 50. DSD Filter-3, High BW
GAIN
vs
GAIN
vs
FREQUENCY
FREQUENCY
0
−1
−2
−3
−4
−5
−6
0
−10
−20
−30
−40
−50
−60
f
= 94 kHz
c
(1)
Gain = –3.3 dB
0
50
100
150
200
0
500
1000
1500
f – Frequency – kHz
f – Frequency – kHz
Figure 51. DSD Filter-4, Low BW
Figure 52. DSD Filter-4, High BW
(1)
This gain is in comparison to PCM 0 dB, when the DSD input signal efficiency is 50%.
All specifications at DBCK = 2.8224 MHz (44.1 kHz × 64 f ), and 50% modulation DSD data input, unless otherwise noted.
S
44
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
DSD MODE CONFIGURATION AND FUNCTION CONTROLS
Configuration for the DSD Interface Mode
The DSD interface mode is selected by setting DSD = 1 (register 20, B5).
B15 B14 B13 B12 B11 B10
B9
0
B8
0
B7
B6
B5
–
B4
B3
–
B2
–
B1
–
B0
–
Register 16 R/W
Register 17 R/W
Register 18 R/W
Register 19 R/W
Register 20 R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
–
–
–
–
–
0
1
–
–
–
–
–
–
1
0
–
–
–
–
DMF1 DMF0
–
–
1
1
REV
–
–
SRST
–
–
OPE
–
–
–
–
–
0
0
1
MONO CHSL OS1
OS0
–
Register 21
Register 22
R
R
0
1
–
–
–
–
–
DZ1
–
DZ0
1
0
–
–
–
–
ZFGR ZFGL
NOTE: –: Function is disabled. No operation even if data bit is set
DMF[1:0]: Analog-FIR Performance Selection
Default value: 00
DMF[1:0]
Analog-FIR Performance Select
00
01
10
11
FIR-1 (default)
FIR-2
FIR-3
FIR-4
Plots for the four analog FIR filter responses are shown in the ANALOG FIR FILTER PERFORMANCE IN DSD
MODE section of this data sheet.
OS[1:0]: Analog-FIR Operation-Speed Selection
Default value: 00
OS[1:0]
00
Operation-Speed Select
f
f
(default)
/2
DBCK
DBCK
01
10
Reserved
f /4
DBCK
11
The OS bit in the DSD mode is used to select the operating rate of the analog FIR. The OS bits must be set before
setting the DSD bit to1.
45
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
TDMCA INTERFACE FORMAT
The PCM1796 supports the time-division-multiplexed command and audio (TDMCA) data format to simplify the host
control serial interface. The TDMCA format is designed not only for the McBSP of TI DSPs but also for any
programmable devices. The TDMCA format can transfer not only audio data but also command data, so that it can
be used together with any kind of device that supports the TDMCA format. The TDMCA frame consists of a command
field, extended command field, and some audio data fields. Those audio data are transported to IN devices (such
as a DAC) and/or from OUT devices (such as an ADC). The PCM1796 is an IN device. LRCK and BCK are used
with both IN and OUT devices so that the sample frequency of all devices in a system must be the same. The TDMCA
mode supports a maximum of 30 device IDs. The maximum number of audio channels depends on the BCK
frequency.
TDMCA Mode Determination
The PCM1796 recognizes the TDMCA mode automatically when it receives an LRCK signal with a pulse duration
of two BCK clocks. If the TDMCA mode operation is not needed, the duty cycle of LRCK must be 50%. Figure 53
shows the LRCK and BCK timing that determines the TDMCA mode. The PCM1796 enters the TDMCA mode after
two continuous TDMCA frames. Any TDMCA commands can be issued during the next TDMCA frame after the
TDMCA mode is entered.
Command
Accept
Pre-TDMCA Frame
TDMCA Frame
LRCK
2 BCKs
BCK
Figure 53. LRCK and BCK Timing for Determination of TDMCA Mode
TDMCA Terminals
TDMCA requires six signals, of which four signals are for command and audio data interface, and one pair for daisy
chaining. Those signals can be shared as in the following table. The DO signal has a 3-state output so that it can
be connected directly to other devices.
TERMINAL TDMCA
PROPERTY
input
DESCRIPTION
NAME
NAME
LRCK
LRCK
TDMCA frame start signal. It must be the same as the sampling frequency.
TDMCA clock. Its frequency must be high enough to communicate a TDMCA frame within an LRCK
cycle.
BCK
BCK
input
DATA
MDO
MC
DI
DO
input
output
input
TDMCA command and audio data input signal
TDMCA command data 3-state output signal
TDMCA daisy-chain input signal
DCI
DCO
MS
output
TDMCA daisy-chain output signal
46
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Device ID Determination
The TDMCA mode also supports a multichip implementation in one system. This means a host controller (DSP) can
simultaneously support several TDMCA devices, which can be of the same type or different types, including PCM
devices. The PCM devices are categorized as IN device, OUT device, IN/OUT device, and NO device. The IN device
has an input port to receive audio data, the OUT device has an output port to supply audio data, the IN/OUT device
has both input and output ports for audio data, and the NO device has no port for audio data but needs command
data from the host. A DAC is an IN device, an ADC is an OUT device, a codec is an IN/OUT device, and a PLL is
a NO device. The PCM1796 is an IN device. For the host controller to distinguish the devices, each device is assigned
its own device ID by the daisy chain. The devices obtain their own device IDs automatically by connecting their DCI
to the DCO of the preceding device and their DCO to the DCI of the following device in the daisy chain. The daisy
chains are categorized as the IN chain and the OUT chain, which are completely independent and equivalent.
Figure 54 shows an example daisy chain connection. If a system needs to chain the PCM1796 and a NO device in
the same IN or OUT chain, the NO device must be chained at the back end of the chain because it does not require
any audio data. Figure 55 shows an example of TDMCA system including an IN chain and an OUT chain with a TI
DSP. For a device to get its own device ID, the DID signal must be set to 1 (see the Command Field section for details),
and LRCK and BCK must be driven in the TDMCA mode for all PCM devices that are chained. The device at the top
of the chain knows its device ID is 1 because its DCI is fixed HIGH. Other devices count the BCK pulses and observe
their own DCI signal to determine their position and ID. Figure 56 shows the initialization of each device ID.
IN Chain
• • •
• • •
• • •
• • •
IN
IN
IN Device
IN Device
NO Device
NO Device
NO Device
NO Device
IN/OUT
Device
IN/OUT
Device
• • •
OUT Device
OUT Device
OUT
OUT
OUT Chain
Figure 54. Daisy Chain Connection
47
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
DCII
LRCK
BCK
DI
IN/OUT
Device
(DIX1700)
DCOI
DCIO
DO
DCOO
Device ID = 1
LRCK
BCK
DI
DCI
IN Device
(PCM1796)
DCO
DO
Device ID = 2
LRCK
BCK
DI
DCI
NO Device
DCO
DO
Device ID = 3
•
•
•
FSX
FSR
CLKX
CLKR
LRCK
BCK
DI
DCI
OUT Device
DX
DCO
DR
DO
Device ID = 2
TI DSP
LRCK
BCK
DI
DCI
OUT Device
DCO
DO
Device ID = 3
•
•
•
Figure 55. IN Daisy Chain and OUT Daisy Chain Connection for a Multichip System
48
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
LRCK
BCK
DID
Command Field
DI
Device ID = 1
Device ID = 2
DCO1
DCO1
DCI2
Device ID = 3
DCO2
DCI3
•
•
•
•
•
•
58 BCKs
Device ID = 30 DCO29
DCI30
Figure 56. Device ID Determination Sequence
TDMCA Frame
In general, the TDMCA frame consists of the command field, extended command (EMD) field, and audio data fields.
All of them are 32 bits in length, but the lowest byte has no meaning. The MSB is transferred first for each field. The
command field is always transferred as the first packet of the frame. The EMD field is transferred if the EMD flag of
the command field is HIGH. If any EMD packets are transferred, no audio data follows the EMD packets. This frame
is for quick system initialization. All devices of a daisy chain should respond to the command field and extended
command field. The PCM1796 has two audio channels that can be selected by OPE (register 19). If the OPE bit is
not set to HIGH, those audio channels are transferred. Figure 57 shows the general TDMCA frame. If some DACs
are enabled, but corresponding audio data packets are not transferred, the analog outputs are unpredictable.
1/f
S
LRCK
BCK
[For Initialization]
Don’t
Care
DI
EMD
CMD
CMD
EMD
EMD
CMD
EMD
EMD
32 Bits
DO
CMD
CMD
CMD
CMD
CMD
CMD
[For Operation]
Don’t
Care
Ch(n)
Ch2
Ch2
Ch4
Ch4
CMD
Ch1
Ch1
Ch3
Ch3
DI
DO
CMD
Ch(m)
Figure 57. General TDMCA Frame
49
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
1/f (256 BCK Clocks)
S
7 Packets × 32 Bits
LRCK
BCK
Don’t
Care
DI
CMD
Ch2
IN and OUT Channel Orders are Completely Independent
Ch1 Ch2
Ch4
Ch5
Ch6
Ch1
CMD
Ch3
DO
CMD
Figure 58. TDMCA Frame Example of 6-Ch DAC and 2-Ch ADC With Command Read
Command Field
The normal command field is defined as follows. When the DID bit (MSB) is 1, this frame is used only for device ID
determination, and all remaining bits in the field are ignored.
31
30
29
28
24
23
22
16 15
8
7
0
command
DID EMD DCS
device ID
R/W
register ID
data
not used
Bit 31: Device ID enable flag
The PCM1796 operates to get its own device ID for TDMCA initialization if this bit is HIGH.
Bit 30: Extended command enable flag
The EMD packet is transferred if this bit is HIGH, otherwise skipped. Once this bit is HIGH, this frame does not contain
any audio data. This is for system initialization.
Bit 29: Daisy chain selection flag
HIGH designates OUT-chain devices, LOW designates IN-chain devices. The PCM1796 is an IN device, so the DCS
bit must be set to LOW.
Bits[28:24]: Device ID
The device ID is 5 bits length, and it can be defined. These bits identify the order of a device in the IN or OUT daisy
chain. The top of the daisy chain defines device ID 1 and successive devices are numbered 2, 3, 4, etc. All devices
for which the DCI is fixed HIGH are also defined as ID 1. The maximum device ID is 30 each in the IN and OUT chains.
If a device ID of 0x1F is used, all devices are selected as broadcast when in the write mode. If a device ID of 0x00
is used, no device is selected.
Bit 23: Command Read/Write flag
If this bit is HIGH, the command is a read operation.
Bits[22:16]: Register ID
It is 7 bits in length.
Bits[15:8]: Command data
It is 8 bits in length. Any valid data can be chosen for each register.
Bits[7:0]: Not used
These bits are never transported when a read operation is performed.
Extended command field
The extended command field is the same as the command field, except that it does not have a DID flag.
31
30
29
28
24
23
22
16 15
8
7
0
extended command rsvd EMD DCS
device ID
R/W
register ID
data
not used
50
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Audio Fields
The audio field is 32 bits in length and the audio data is transferred MSB first, so the other fields must be stuffed with
0s as shown in the following example.
31
16
12
8
7
4 3
0
audio data MSB
24 bits
LSB
All 0s
TDMCA Register Requirements
TDMCA mode requires device ID and audio channel information, previously described. The OPE bit in register 19
indicates audio channel availability and register 23 indicates the device ID. Register 23 is used only in the TDMCA
mode. See the mode control register map (Table 4).
Register Write/Read Operation
The command supports register write and read operations. If the command requests to read one register, the read
data is transferred on DO during the data phase of the timing cycle. The DI signal can be retrieved at the positive
edge of BCK, and the DO signal is driven at the negative edge of BCK. DO is activated one BCK cycle early to
compensate for the output delay caused by high impedance. Figure 59 shows the TDMCA write and read timing.
Register ID Phase
Data Phase
BCK
Read Mode and Proper Register ID
Write Data Retrieved, if Write Mode
DI
Read Data Driven, if Read Mode
1 BCK Early
DO
DOEN
(Internal)
Figure 59. TDMCA Write and Read Operation Timing
TDMCA-Mode Operation
DCO specifies the owner of the next audio channel in TDMCA-mode operation. When a device retrieves its own audio
channel data, DCO goes HIGH during the last audio channel period. Figure 60 shows the DCO output timing in
TDMCA-mode operation. The host controller ignores the behavior of DCI and DCO. DCO indicates the last audio
channel of each device. Therefore, DCI means the next audio channel is allocated.
If some devices are skipped due to no active audio channel, the skipped devices must notify the next device that the
DCO will be passed through the next DCI. Figure 61 and Figure 62 show DCO timing with skip operation. Figure 63
shows the ac timing of the daisy chain signals.
51
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
1/f (384 BCK Clocks)
S
9 Packets y 32 Bits
LRCK
BCK
IN Daisy Chain
Ch2 Ch3 Ch4 Ch5
CMD Ch1
Ch6 Ch7 Ch8
Don’t Care
CMD
DI
DCI1
DID = 1
DID = 2
DCO1
DCI2
DCO2
DCI3
DID = 3
DID = 4
DCO3
DCI4
DCO4
Figure 60. DCO Output Timing of TDMCA Mode Operation
1/f (256 BCK Clocks)
S
5 Packets × 32 Bits
LRCK
BCK
DI
CMD
Ch1
Ch2
Ch15
Ch16
Don’t Care
CMD
DCI
DID = 1
DID = 2
DCO
DCI
2 BCK Delay
14 BCK Delay
DCO
•
•
•
•
•
•
•
•
•
DCI
DID = 8
DCO
Figure 61. DCO Output Timing With Skip Operation
52
ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
Command Packet
LRCK
BCK
DI
DID EMD
DCO1
DCO2
•
•
•
Figure 62. DCO Output Timing With Skip Operation (for Command Packet 1)
53
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
LRCK
t
t
(BL)
(LB)
BCK
t
t
t
(DH)
(BCY)
(DS)
DI
t
(DOE)
DO
t
t
(DH)
(DS)
DCI
DCO
t
(COE)
PARAMETER
MIN MAX UNITS
t
BCK pulse cycle time
LRCK setup time
LRCK hold time
DI setup time
20
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
(BCY)
t
t
t
t
t
t
(LB)
3
(BL)
(DS)
(DH)
(DS)
(DH)
0
DI hold time
3
DCI setup time
DCI hold time
0
3
(1)
DO output delay
t
8
6
(DOE)
(1)
DCO output delay
t
(COE)
(1)
Load capacitance is 10 pF.
Figure 63. AC Timing of Daisy Chain Signals
54
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
www.ti.com
SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006
ANALOG OUTPUT
Table 5 and Figure 64 show the relationship between the digital input code and analog output.
Table 5. Analog Output Current and Voltage
800000 (–FS)
–1.5
000000 (BPZ)
7FFFFF (+FS)
–5.5
I
N [mA]
P [mA]
–3.5
–3.5
–2.87
–2.87
0
OUT
I
–5.5
–1.5
OUT
V
N [V]
P [V]
–1.23
–4.51
OUT
V
–4.51
–1.23
OUT
V
[V]
–2.98
2.98
OUT
NOTE: V
N is the output of U1, V
measurementcircuit of Figure 36.
P is the output of U2, and V
OUT
is the output of U3 in the
OUT
OUT
OUTPUT CURRENT
vs
INPUT CODE
0
−1
−2
−3
−4
−5
−6
I
N
OUT
I
P
OUT
800000(–FS)
000000(BPZ)
7FFFFF(+FS)
Input Code – Hex
Figure 64. The Relationship Between Digital Input and Analog Output
55
PACKAGE OPTION ADDENDUM
www.ti.com
7-Apr-2023
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
PCM1796DB
ACTIVE
ACTIVE
SSOP
SSOP
DB
DB
28
28
47
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-25 to 85
-25 to 85
PCM1796
PCM1796
Samples
Samples
PCM1796DBR
2000 RoHS & Green
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-Apr-2023
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Jun-2023
TUBE
T - Tube
height
L - Tube length
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
PCM1796DB
PCM1796DB
DB
DB
SSOP
SSOP
28
28
47
47
500
530
10.6
10.5
500
9.6
4.1
4000
Pack Materials-Page 1
PACKAGE OUTLINE
DB0028A
SSOP - 2 mm max height
S
C
A
L
E
1
.
5
0
0
SMALL OUTLINE PACKAGE
C
8.2
7.4
TYP
A
0.1 C
SEATING
PIN 1 INDEX AREA
PLANE
26X 0.65
28
1
2X
10.5
9.9
8.45
NOTE 3
14
15
0.38
0.22
28X
0.15
C A B
5.6
5.0
B
NOTE 4
2 MAX
0.25
GAGE PLANE
(0.15) TYP
SEE DETAIL A
0.95
0.55
0.05 MIN
0 -8
A
15
DETAIL A
TYPICAL
4214853/B 03/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-150.
www.ti.com
EXAMPLE BOARD LAYOUT
DB0028A
SSOP - 2 mm max height
SMALL OUTLINE PACKAGE
SYMM
28X (1.85)
(R0.05) TYP
28
1
28X (0.45)
26X (0.65)
SYMM
14
15
(7)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 10X
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
15.000
(PREFERRED)
SOLDER MASK DETAILS
4214853/B 03/2018
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DB0028A
SSOP - 2 mm max height
SMALL OUTLINE PACKAGE
28X (1.85)
SYMM
(R0.05) TYP
28
1
28X (0.45)
26X (0.65)
SYMM
14
15
(7)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 10X
4214853/B 03/2018
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明