PT6310G [TI]
2A SWITCHING REGULATOR, 800kHz SWITCHING FREQ-MAX, PDFM12, PLASTIC, SIP-12;
| 型号： | PT6310G |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 2A SWITCHING REGULATOR, 800kHz SWITCHING FREQ-MAX, PDFM12, PLASTIC, SIP-12 局域网 开关 光电二极管 |
| 文件： | 总12页 (文件大小：596K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
For assistance or to order, call (800) 531-5782
P T 6 3 1 0 S e r i e s
SLTS076
(Revised 8/17/99)
2 AMP ADJUSTABLE POSITIVE STEP-DOWN
INTEGRATED SWITCHING REGULATOR
• 87% Efficiency
Switching Regulator (ISR) designed to
• Adjustable Output Voltage
• Internal Short Circuit Protection
• Over-Temperature Protection
• On/Off Control (Ground Off)
• Small SIP Footprint
meet the on-board power conversion
needs of battery powered or other equip-
ment requiring high efficiency and
small size. This high performance ISR
offers a unique combination of features
combining 87% typical efficiency with
open-collector on/off control and ad-
justable output voltage.
• Wide Input Range
The PT6310 series is a High-
Performance 2 Amp, 12-Pin SIP
(Single In-line Package) Integrated
Quiescent current in the shutdown
mode is typically less than 100µA.
Pin-Out Information
Ordering Information
PT 6310! = +14.6 Volts
PT 6311! = +15.5 Volts
PT 6312! = +15.0 Volts
PT 6313! = +8.0 Volts
PT Series Suffix
Case/Pin
Configuration
(PT1234X)
Pin Function
Inhibit
1
(30V max)
Vertical Through-Hole
N
A
C
2
3
Vin
Vin
Standard Application
Horizontal Through-Hole
Horizontal Surface Mount
VOADJ
12
4
Vin
VIN
VOUT
2,3,4
9,10,11
C2
5
GND
GND
GND
GND
Vout
PT6300
1
6
7
Pkg Style 200
5,6,7,8
+
C1
INH
Q1
8
9
COM
COM
C1 = Optional 1µF ceramic
C2 = Required 100µF electrolytic
Q1 = NFET
10
11
12
Vout
Vout
Vout Adj
Specifications
PT6310 Series
Characteristics
(T = 25°C unless noted)
a
Symbols
Conditions
Min
Typ
Max
Units
Output Current
Io
Isc
Over Vin range
Vin = Vo + 5V
0.1 ≤ Io ≤ 2.0 A
Over Vin Range, Io = 2.0 A
Ta = 0°C to +60°C
0.1*
—
—
5.0
—
2.0
—
A
Apk
V
Short Circuit Current
Input Voltage Range
Output Voltage Tolerance
Vin
∆Vo
Vo + 4
38**
—
1.0
2.0
%Vo
Line Regulation
Load Regulation
Vo Ripple/Noise
Regline
Regload
Vn
Over Vin range
—
—
—
0.25
0.25
2
0.5
0.5
—
%Vo
%Vo
%Vo
0.1 ≤ Io ≤ 2.0 A
Vin = Vin min, Io = 2.0A
Transient Response
with Co = 100µF
ttr
50% load change
—
—
100
200
—
µSec
%Vo
Vos
Vo over/undershoot
5.0
87
Efficiency
η
Vin=24V, Io = 2.0 A
—
—
%
Switching Frequency
ƒo
Over Vin and Io ranges
600
500
700
550
800
600
kHz
kHz
PT6312 only
Shutdown Current
Quiescent Current
Isc
Inl
Vo
Vin = 15V
Io = 0A, Vin =10V
—
—
100
10
—
—
µA
mA
Output Voltage
Below Vo
Above Vo
See Application Notes.
Adjustment Range
Absolute Maximum
Ta
Ta
-40
-40
—
—
+85
+70
°C
Operating Temperature Range
Recommendated Operating
Temperature Range
Free Air Convection, (40-60LFM)
At Vin = 18V, Io = 2.0A
°C
Thermal Resistance
Storage Temperature
Mechanical Shock
θja
Free Air Convection (40-60LFM)
—
—
30
—
—
°C/W
Ts
-40
+125
—
°C
Per Mil-STD-883D, Method 2002.3, 1 msec,
Half Sine, mounted to a fixture
—
500
G’s
Mechanical Vibration
Weight
Per Mil-STD-883D, Method 2007.2,
20-2000 Hz,Soldered in a PC board
—
—
10
—
—
G’s
—
—
6.5
grams
*
ISR will operate to no load with reduced specifications.
** Input voltage cannot exceed 30V when the inhibit function is used.
Note: The PT6310 requires a 100µF electrolytic or tantalum output capacitor for proper operation in all applications.
Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 http://www.ti.com/powertrends
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
MECHANICAL DATA
MPSI029 – SEPTEMBER 2001
EBG (R–PSIP–T12)
PLASTIC SINGLE–IN–LINE MODULE
Suffix G
2.36 (59,94) MAX.
2.030 (51,56)
0.325
(8,25)
1.71 (43,43) MAX.
0.50
0.55
0.19 (4,82)
(13,97)
(12,70)
Note G
0.38
0.67 (17,01)
MAX.
(9,65)
0.017
(0,43)
TYP.
1
0.32
(8,12)
0.40 (10,16)
0.30 (7,62)
0.040
(1,01)
0.140
0.017 (0,43) TYP.
0.100 (2,54) TYP.
ø0.187 (4,75)
2 Places
(3,55)
MIN.
0.38 (9,65)
MAX.
2.42 (61,46)
2.030 (51,56)
1.77 (44,95)
1.21 (30,73)
Hole for #6–32 screws
0.325
(8,25)
0.28
(7,11)
0.18 (4,57)
Note E
Note F
0.78
(19,81)
0.41 (10,41)
0.360 (9,14)
0.20
(5,08)
1
0.040 (1,01)
0.07
(1,77)
ø0.035 (0,88) MIN. 12 Places
Plated through
0.335
(8,50)
0.100 (2,54) 11 Places
0.465 (11,81)
PC LAYOUT
4203445/A 08/01
NOTES: A. All linear dimensions are in inches (mm).
B. This drawing is subject to change without notice.
C. 2 place decimals are ꢀ0.030 (ꢀ0,76mm).
D. 3 place decimals are ꢀ0.010 (ꢀ0,25mm).
E. Recommended mechanical keep out area.
F. No copper, power or signal traces in this area.
G. The metal tab is isolated but electrically conductive. No
signal traces are allowed under the metal tab area. A
solid copper island is recommended, which may be
grounded.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, maskworkright, orotherTIintellectualpropertyrightrelatingtoanycombination, machine, orprocess
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2001, Texas Instruments Incorporated
MECHANICAL DATA
MPSI027 – SEPTEMBER 2001
EBE (R–PSIP–T12)
PLASTIC SINGLE-IN-LINE MODULE
Suffix R
2.36 (59,94) MAX.
2.030 (51,56)
0.325
(8,25)
1.71 (43,43) MAX.
0.50
0.55
0.19 (4,82)
(13,97)
(12,70)
Note F
0.38
(9,65)
0.67 (17,01)
MAX.
1
0.32 (8,12)
0.40
(10,16)
ø0.187 (4,75)
2 Places
0.170 (4,31)
MIN.
0.017 (0,43) TYP.
0.100 (2,54) TYP.
0.017 (0,43)
TYP.
0.38 (9,65)
MAX.
0.30 (7,62)
0.465
(11,81)
2.42 (61,46)
1.77 (44,95)
0.325
(8,25)
0.335 (8,50)
0.040 (1,01)
0.100 (2,54) 11 Places
1
0.42
(10,66)
0.070
(1,77)
0.100 (2,54)
ø0.035 (0,88) MIN. 12 Places
Plated through
Note E
PC Layout
4203443/A 08/01
NOTES:
A. All linear dimensions are in inches (mm).
B. This drawing is subject to change without notice.
C. 2 place decimals are " 0.030 (" 0, 76 mm).
3 place decimals are " 0.010 (" 0, 25 mm).
D.
E. Recommended mechanical keep-out area.
F. The metal tab is isolated but electrically
conductive. It can be grounded.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, maskworkright, orotherTIintellectualpropertyrightrelatingtoanycombination, machine, orprocess
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2001, Texas Instruments Incorporated
MECHANICAL DATA
MPSI032 – SEPTEMBER 2001
PLASTIC SINGLE-IN-LINE MODULE
Suffix B
EBK (R–PSIP–G12)
2.36 (59,94) MAX.
2.030 (51,56)
0.325
(8,25)
1.71 (43,43) MAX.
0.50
(12,70)
0.55
(13,97)
0.19 (4,82)
Note H
0.38
(9,65)
0.67 (17,01)
MAX.
1
0.32
(8,12)
0.40 (10,16)
0.30 (7,62)
0.080
(2,02)
MIN.
0.017 (0,43) TYP.
0.100 (2,54) TYP.
ø0.187 (4,75)
2 Places
0.38
(9,65)
MAX.
0.006 (0,15)
MAX.
Seating Plane
2.42 (61,46)
2.030 (51,56)
1.77 (44,95)
1.21 (30,73)
Hole for #6–32 screws
0.325
(8,25)
0.28
(7,11)
0.18 (4,57)
Note E
Note F
0.10
(2,54)
0.41 (10,41)
0.81
(20,57)
C/L
1
0.350
(8,89)
0.17
(4,31)
Note G
0.040
(1,01)
0.040 (1,01) 12 Places
0.150
(3,81)
0.335
(8,50)
0.100 (2,54) 11 Places
PC Layout
0.465 (11,81)
0°–7°
Gage Plane
0.017 (0,43)
TYP.
4203448/A 08/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. 2 place decimals are ꢀ0.030 (ꢀ0,76mm).
D. 3 place decimals are ꢀ0.010 (ꢀ0,25mm).
E. Recommended mechanical keep out area.
F. No copper, power or signal traces in this area.
G. Power pin connections should utilize two or more vias
per input, ground and output pin.
H. The metal tab is isolated but electrically conductive. No
signal traces are allowed under the metal tab area. A
solid copper island is recommended, which may be
grounded.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, maskworkright, orotherTIintellectualpropertyrightrelatingtoanycombination, machine, orprocess
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2001, Texas Instruments Incorporated
Product Folder: PT6310, 14.6V 2A Wide-Input Adjustable Step-Down ISR
All Semiconductors
____________________
SAMPLES
FEATURES | DESCRIPTION | DATASHEETS | PRICING/AVAILABILITY/PKG | APPLICATION NOTES
| RELATED DOCUMENTS
PRODUCT FOLDER | PRODUCT INFO:
PT6310, 14.6V 2A Wide-Input Adjustable Step-Down ISR
DEVICE STATUS: ACTIVE
PARAMETER NAME PT6310
VI (max) (V)
VI (min) (V)
IO (A)
38
18.6
2
VO (V)
14.6
Back to Top
FEATURES
● 87% Efficiency
● Adjustable Output Voltage
● Internal Short Circuit Protection
● Over-Temperature Protection
● On/Off Control (Ground Off)
● Small SIP Footprint
● Wide Input Range
Back to Top
DESCRIPTION
The PT6310 series is a High-Performance 2 Amp, 12-Pin SIP (Single In-line Package) Integrated Switching Regulator (ISR)
designed to meet the on-board power conversion needs of battery powered or other equipment requiring high efficiency and
small size. This high performance ISR offers a unique combination of features combining 87% typical efficiency with
open-collector on/off control and adjustable output voltage.
Quiescent current in the shutdown mode is typically less than 100uA.
Back to Top
Back to Top
TECHNICAL DOCUMENTS
To view the following documents, Acrobat Reader 4.0 is required.
To download a document to your hard drive, right-click on the link and choose 'Save'.
DATASHEET
Full datasheet in Acrobat PDF: slts076.pdf (373 KB) (Updated: 06/12/2000)
Full datasheet in Zipped PostScript: slts076.psz (648 KB)
Back to Top
APPLICATION NOTES
● Analog Applications Journal July 2001 Issue (SLYT027 - Updated: 07/09/2001)
● Reflow Soldering Requirements for Plug-In Power Suface-Mount Products (SLTA051 - Updated: 08/01/2000)
Back to Top
RELATED DOCUMENTS
● Power Trends Product Selector Guide (SLTT063A, 31 KB - Updated: 08/16/2000)
Back to Top
PRICING/AVAILABILITY/PKG
BUDGETARY PRICE
ORDERABLE DEVICE PACKAGE PINS TEMP (ºC) STATUS
US$/UNIT
PACK QTY PRICING/AVAILABILITY/PKG
QTY=1000+
EBG
EBE
Check stock or order
Check stock or order
PT6310G
PT6310R
12
12
ACTIVE
ACTIVE
12.39
12.39
12
120
file:////roarer/root/export/projects/bitting2/imaging/BITTING/mail_pdf/cpl_images/pt6310.html (1 of 2) [11/13/2001 4:16:58 PM]
Product Folder: PT6310, 14.6V 2A Wide-Input Adjustable Step-Down ISR
Table Data Updated on: 10/21/2001
© Copyright 2001 Texas Instruments Incorporated. All rights reserved. Trademarks | Privacy Policy | Important Notice
file:////roarer/root/export/projects/bitting2/imaging/BITTING/mail_pdf/cpl_images/pt6310.html (2 of 2) [11/13/2001 4:16:58 PM]
Product Folder: PT6311, 15.5V 2A Wide-Input Adjustable Step-Down ISR
All Semiconductors
____________________
SAMPLES
FEATURES | DESCRIPTION | DATASHEETS | PRICING/AVAILABILITY/PKG | APPLICATION NOTES
| RELATED DOCUMENTS
PRODUCT FOLDER | PRODUCT INFO:
PT6311, 15.5V 2A Wide-Input Adjustable Step-Down ISR
DEVICE STATUS: ACTIVE
Back to Top
FEATURES
● 87% Efficiency
● Adjustable Output Voltage
● Internal Short Circuit Protection
● Over-Temperature Protection
● On/Off Control (Ground Off)
● Small SIP Footprint
● Wide Input Range
Back to Top
DESCRIPTION
The PT6310 series is a High-Performance 2 Amp, 12-Pin SIP (Single In-line Package) Integrated Switching Regulator (ISR)
designed to meet the on-board power conversion needs of battery powered or other equipment requiring high efficiency and
small size. This high performance ISR offers a unique combination of features combining 87% typical efficiency with
open-collector on/off control and adjustable output voltage.
Quiescent current in the shutdown mode is typically less than 100uA.
Back to Top
Back to Top
TECHNICAL DOCUMENTS
To view the following documents, Acrobat Reader 4.0 is required.
To download a document to your hard drive, right-click on the link and choose 'Save'.
DATASHEET
Full datasheet in Acrobat PDF: slts076.pdf (373 KB) (Updated: 06/12/2000)
Full datasheet in Zipped PostScript: slts076.psz (648 KB)
Back to Top
APPLICATION NOTES
● Analog Applications Journal July 2001 Issue (SLYT027 - Updated: 07/09/2001)
● Reflow Soldering Requirements for Plug-In Power Suface-Mount Products (SLTA051 - Updated: 08/01/2000)
Back to Top
RELATED DOCUMENTS
● Power Trends Product Selector Guide (SLTT063A, 31 KB - Updated: 08/16/2000)
Back to Top
PRICING/AVAILABILITY/PKG
BUDGETARY PRICE
ORDERABLE DEVICE PACKAGE PINS TEMP (ºC) STATUS
US$/UNIT
PACK QTY PRICING/AVAILABILITY/PKG
QTY=1000+
EBG
EBD
EBE
Check stock or order
Check stock or order
Check stock or order
PT6311G
PT6311N
PT6311R
12
12
12
ACTIVE
ACTIVE
ACTIVE
12.39
11.89
12.39
12
12
120
Table Data Updated on: 10/21/2001
© Copyright 2001 Texas Instruments Incorporated. All rights reserved. Trademarks | Privacy Policy | Important Notice
file:////roarer/root/export/projects/bitting2/imaging/BITTING/mail_pdf/cpl_images/pt6311.html [11/13/2001 4:23:06 PM]
Product Folder: PT6312, 15V 2A Wide-Input Adjustable Step-Down ISR
All Semiconductors
____________________
SAMPLES
FEATURES | DESCRIPTION | DATASHEETS | PRICING/AVAILABILITY/PKG | APPLICATION NOTES
| RELATED DOCUMENTS
PRODUCT FOLDER | PRODUCT INFO:
PT6312, 15V 2A Wide-Input Adjustable Step-Down ISR
DEVICE STATUS: ACTIVE
Back to Top
FEATURES
● 87% Efficiency
● Adjustable Output Voltage
● Internal Short Circuit Protection
● Over-Temperature Protection
● On/Off Control (Ground Off)
● Small SIP Footprint
● Wide Input Range
Back to Top
DESCRIPTION
The PT6310 series is a High-Performance 2 Amp, 12-Pin SIP (Single In-line Package) Integrated Switching Regulator (ISR)
designed to meet the on-board power conversion needs of battery powered or other equipment requiring high efficiency and
small size. This high performance ISR offers a unique combination of features combining 87% typical efficiency with
open-collector on/off control and adjustable output voltage.
Quiescent current in the shutdown mode is typically less than 100uA.
Back to Top
Back to Top
TECHNICAL DOCUMENTS
To view the following documents, Acrobat Reader 4.0 is required.
To download a document to your hard drive, right-click on the link and choose 'Save'.
DATASHEET
Full datasheet in Acrobat PDF: slts076.pdf (373 KB) (Updated: 06/12/2000)
Full datasheet in Zipped PostScript: slts076.psz (648 KB)
Back to Top
APPLICATION NOTES
● Analog Applications Journal July 2001 Issue (SLYT027 - Updated: 07/09/2001)
● Reflow Soldering Requirements for Plug-In Power Suface-Mount Products (SLTA051 - Updated: 08/01/2000)
Back to Top
RELATED DOCUMENTS
● Power Trends Product Selector Guide (SLTT063A, 31 KB - Updated: 08/16/2000)
Back to Top
PRICING/AVAILABILITY/PKG
BUDGETARY PRICE
ORDERABLE DEVICE PACKAGE PINS TEMP (ºC) STATUS
US$/UNIT
PACK QTY PRICING/AVAILABILITY/PKG
QTY=1000+
EBK
EBG
EBD
EBE
Check stock or order
Check stock or order
Check stock or order
Check stock or order
PT6312B
PT6312G
PT6312N
PT6312R
12
12
12
12
ACTIVE
ACTIVE
ACTIVE
ACTIVE
12.39
12.39
11.89
12.39
12
12
12
120
Table Data Updated on: 10/21/2001
© Copyright 2001 Texas Instruments Incorporated. All rights reserved. Trademarks | Privacy Policy | Important Notice
file:////roarer/root/export/projects/bitting2/imaging/BITTING/mail_pdf/cpl_images/pt6312.html [11/13/2001 4:47:42 PM]
相关型号：
PT6311G
IC 2 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PDFM12, PLASTIC, SIP-12, Switching Regulator or Controller
TI
©2020 ICPDF网 联系我们和版权申明