PT6682R [TI]
5A SWITCHING REGULATOR, 600kHz SWITCHING FREQ-MAX, SMA14, VERTICAL MOUNT PACKAGE-14;型号: | PT6682R |
厂家: | TEXAS INSTRUMENTS |
描述: | 5A SWITCHING REGULATOR, 600kHz SWITCHING FREQ-MAX, SMA14, VERTICAL MOUNT PACKAGE-14 开关 |
文件: | 总5页 (文件大小:136K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PT6680 Series
5 Amp 18-36V Input
Integrated Switching Regulator
SLTS098
(Revised 6/30/2000)
• Single Device: 5A Output
• Input Voltage Range: 18V to 36V
• Adjustable Output Voltage
• 80% Efficiency
• Remote Sense Capability
• Standby Function
trial applications requiring as much as
36V input and 5A of output current,
the PT6680 is packaged in a 14-Pin
SIP (Single In-line Package) and is
available in a surface-mount configu-
ration.
Only two external capacitors are
required for proper operation. Please
note that this product does not include
short circuit protection.
The PT6680 series is a new addi-
tion to Power Trends’ line of 24V bus
Integrated Switching Regulators (ISRs).
Designed for general purpose indus-
Pin-Out Information
Ordering Information PT Series Suffix
(PT1234X)
1
Remote Sense
Do Not Connect
STBY*- Standby
Vin
PT 6681! = +3.3 Volts
PT 6682! = +2.5 Volts
PT 6683! = +5.0 Volts
PT 6684! = +9.0 Volts
PT 6685! = +15.0 Volts
PT 6686! = +12.0 Volts
Case/Pin
Configuration
Heat
Heat Spreader
2
3
4
Spreader with Side Tabs
Standard Application
Vertical Through-Hole
Horizontal Through-Hole
Horizontal Surface Mount
P
R
G
B
REMOTE SENSE
1
5
Vin
D
E
VIN
VOUT
4,5,6
3
11,12,13
6
Vin
PT6680
7
GND
7,8,9,10
+
+
LOAD
C1
C2
8
9
GND
GND
STBY
COM
Q1
COM
(1)
Pkg Style 400
PT6680
10GND
Note: Back surface
of product is
conducting metal
C1 = Required 560µF electrolytic
C2 = Required 330µF electrolytic
Q1= NFET-or Open Collector Gate
11
12
13
Vout
Vout
Vout
14
Vout Adjust
Specifications
PT6680 SERIES
Characteristics
(T = 25°C unless noted)
a
Symbols
Conditions
Min
Typ
Max
Units
(2)
(2)
Output Current
Io
Ta = 60°C, 200 LFM, pkg P
Ta = 25°C, natural convection
0.1
0.1
—
—
5.0
5.0
A
Input Voltage Range
Vin
0.1A ≤ Io ≤ Iomax
+18V
—
+36V
V
Output Voltage Tolerance
∆Vo
Over Vin range
Vo-0.1
—
Vo+0.1
V
V
Ta = -40°C to +65°C
Output Voltage Adjust Range
Voadj
Pin 14 to Vo or ground
Vo = +3.3V
Vo = +2.5V
Vo = +5.0V
Vo = +9.0V
2.2
1.8
3.0
6.0
—
—
—
—
4.7
4.3
6.5
10.2
13.6
17.0
Vo
=
+12V
9.0—
Vo = +15V
10.0
—
—
Line Regulation
Load Regulation
Vo Ripple/Noise
Regline
Regload
Vn
+18V≤Vin≤+36V, Io = Iomax
Vin = +28V, 0.1≤ Io≤ Iomax
Vin = +28V, Io = Iomax
0.5
0.5
1.0
1.0
%Vo
%Vo
—
Vo
Vo
<
>
+6V
—
50—
mVpp
+6V
1.0%Vo
Transient Response
with C2 = 330µF
ttr
Io step between 2.5A and 5.0A
Vo over/undershoot
—
—
100
—
—
µSec
mV
Vos
100
Efficiency
η
Vin = +28V, Io = Io max
Vo = +3.3V
Vo = +2.5V
Vo = +5.0V
Vo = +9.0V
Vo = +12.0V
Vo = +15.0V
—
—
—
—
—
—
78
73
82
87
88
90
—
—
—
—
—
—
%
Switching Frequency
ƒo
+18V ≤ Vin ≤ +36V
00k5H5z06500
-40—
Over Io range
Maximum Operating
Temperature Range
Ta
Over Vin range
(3)
+85
+125
500
°C
Storage Temperature
Mechanical Shock
Ts
—
—
—
-40—
—
°C
Per Mil-STD-883D, Method 2002.3
—
—
—
G’s
Mechanical Vibration
Per Mil-STD-883D, Method 2007.2,
20-2000 Hz, soldered in a PC board
—
—
7.5
14
G’s
Weight
—
—
grams
Notes (1) The 560µF electrolytic input capacitor must be rated for 1.5Arms ripple current. Both an input and output capacitor is required for proper operation.
(2) The ISR will operate down to no load with reduced specifications.
(3) Consult the SOA curves or contact the factory to determine the appropriate derating.
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Typical Characteristics
PT6680 Series
5 Amp 18-36V Input
Integrated Switching Regulator
PT6681, V =3.3V (Note A)
out
Efficiency vs Output Current
90
85
80
75
70
65
60
55
50
VIN
18.0V
24.0V
36.0V
0
1
2
3
4
5
Iout (A)
Ripple vs Output Current
25
20
15
10
5
VIN
18.0V
24.0V
36.0V
0
0
1
2
3
4
5
Iout (A)
Power Dissipation vs Output Current
6
5
4
3
2
1
0
VIN
36.0V
24.0V
18.0V
0
1
2
3
4
5
Iout (A)
Note A: Characteristic data in the above graphs has been developed from actual products tested at 25°C. This data is considered typcial for the ISR.
Note B: SOA curves represent conditions at which internal components are at or below manufacturer’s maximum operating temperatures.
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Application Notes
PT6680 Series
Adjusting the Output Voltage of the
PT6680 5Amp 18-36V Bus Converter Series
Figure 1
The output voltage of the Power Trends PT6680 Series
ISRs may be adjusted higher or lower than the factory
trimmed pre-set voltage with the addition of a single
external resistor . Table 1 gives the respective allowable
adjustment range for each model in the series as Va (min)
and Va (max).
1
Vsense
4,5,6
11,12,13
Vin
Vo
Vin
PT6680
Vo
1
STBY
GND
Vo(adj)
3
7,8,9,10 14
(R1)
Adj Down
L
O
A
D
+
+
C in
Cout
Adjust Up:
An increase in the output voltage is
R2
Adjust
Up
obtained by adding a resistor R2, between pin 14 (Vo ad-
just) and pins 7-10 (GND).
C O M
C O M
Adjust Down:
Add a resistor (R1), between pin 14 (Vo
adjust) and pins 11-13 (Vout).
Refer to Figure 1 and Table 2 for both the placement and value
of the required resistor, either (R1) or R2 as appropriate.
The values of (R1) [adjust down], and R2 [adjust up], can
also be calculated using the following formulae.
Notes:
1. Use only a single 1% resistor in either the (R1) or R2
location. Place the resistor as close to the ISR as possible.
2. Never connect capacitors from Vo adjust to either GND,
Vout, or the Remote Sense pin. Any capacitance added to
the Vo adjust pin will affect the stability of the ISR.
3. If the Remote Sense feature is being used, connecting the
resistor (R1) between pin 14 (Vo adjust) and pin 1 (Remote
Sense) can benefit load regulation.
Ro (Vo – 1.25)(Va – 1.25)
(R1)
R2
=
=
– Rs kΩ
1.25 (Vo – Va)
Ro (Vo – 1.25)
Va - Vo
– Rs
kΩ
4. For output voltages above 10.0Vdc, the maximum output
current must be limited to 4Adc.
Where: Vo = Original output voltage
Va = Adjusted output voltage
5. Adjustments to the output voltage may place additional
limits on the input voltage for the part. The revised limits
must comply with the following requirements.
Ro = The resistance value in Table 1
Rs = The series resistance from Table 1
Vin (min)
= (Vout + 3)V or 18V,
whichever is higher.
= (10 x Vout )V or 36V,
whichever is less.
Vin (max)
Table 1
PT6680 ADJUSTMENT AND FORMULA PARAMETERS
Series Pt #
V (nom)
PT6682
PT6681
PT6683
PT6684
PT6686
PT6685
2.5V
1.8V
4.3V
4.99
2.49
3.3V
2.2V
4.7V
4.22
4.99
5.0V
3.0V
6.5V
2.49
4.99
9.0V
6.0V
12.0V
9.0V
15.0V
10.0V
17.0V
o
V (min)
a
V (max)
a
10.2V
13.6V
R
(kΩ)
(kΩ)
2.02.02.0
12.7
o
R
s
12.7
12.7
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Application Notes continued
PT6680 Series
Table 2
PT6680 ADJUSTMENT RESISTOR VALUES
Series Pt #
Current
PT6682
5Adc
PT6681
5Adc
PT6683
5Adc
Series Pt #
Current
PT6684
5Adc
PT6686
4Adc
PT6685
4Adc
V (nom)
o
2.5Vdc
3.3Vdc
5.0Vdc
V (nom)
o
9.0Vdc
12.0Vdc
15.0Vdc
V (req’d)
a
V (req’d)
a
6.0
6.2
(6.9)kΩ
(9.2)kΩ
1.8
1.9
(1.4)kΩ
(2.9)kΩ
(5.0)kΩ
(8.1)kΩ
(13.3)kΩ
(23.7)kΩ
(54.9)kΩ
6.4
(11.9)kΩ
(14.0)kΩ
(18.6)kΩ
(23.0)kΩ
(28.3)kΩ
(35.0)kΩ
(43.5)kΩ
(55.0)kΩ
(71.0)kΩ
(95.0)kΩ
(135.0)kΩ
(215.0)kΩ
(455.0)kΩ
2.0
6.6
2.1
6.8
2.2
(1.0)kΩ
(2.3)kΩ
7.0
2.3
7.2
2.4
(3.9)kΩ
7.4
2.5
(5.8)kΩ
7.6
2.6
59.9kΩ
28.7kΩ
18.3kΩ
13.1kΩ
10.0kΩ
7.9kΩ
6.4kΩ
5.3kΩ
4.4kΩ
3.8kΩ
3.2kΩ
2.7kΩ
2.3kΩ
2.0kΩ
Ω
(8.4)kΩ
7.8
2.7
(11.7)kΩ
(16.5)kΩ
(23.6)kΩ
(35.4)kΩ
(59.0)kΩ
(130.0)kΩ
8.0
2.8
8.2
2.9
8.4
3.0
(1.6)kΩ
(2.3)kΩ
8.6
3.1
8.8
3.2
(3.1)kΩ
9.0
(31.7)kΩ
(36.1)kΩ
(41.2)kΩ
(47.1)kΩ
(54.1)kΩ
(62.6)kΩ
(72.8)kΩ
(85.7)kΩ
(102.0)kΩ
(124.0)kΩ
(155.0)kΩ
(201.0)kΩ
(278.0)kΩ
(432.0)kΩ
(895.0)kΩ
3.3
(4.0)kΩ
9.2
64.8kΩ
26.1kΩ
13.1kΩ
6.7kΩ
2.8kΩ
3.4
81.5kΩ
38.3kΩ
23.8kΩ
16.6kΩ
12.3kΩ
9.4kΩ
7.4kΩ
5.8kΩ
4.6kΩ
3.7kΩ
2.9kΩ
2.2kΩ
1.7kΩ
1.2kΩ
(5.1)kΩ
9.4
3.5
(6.2)kΩ
9.6
3.6
(7.6)kΩ
9.8
3.7
(9.1)kΩ
10.0
10.2
10.4
10.6
10.8
11.0
11.2
11.4
11.6
11.8
12.0
12.2
12.4
12.6
12.8
13.08.8k
13.2
13.4
13.6
13.8
14.0
14.2
14.5
15.0
15.5
16.014.8k
16.5
17.01.1k
(25.8)kΩ
(28.3)kΩ
(31.1)kΩ
(34.1)kΩ
(37.3)kΩ
(40.9)kΩ
(44.9)kΩ
(49.3)kΩ
(54.3)kΩ
(59.8)kΩ
(66.1)kΩ
(73.3)kΩ
(81.6)kΩ
(91.3)kΩ
(103.0)kΩ
(117.0)kΩ
(133.0)kΩ
(154.0)kΩ
(181.0)kΩ
(217.0)kΩ
(268.0)kΩ
(343.0)kΩ
(570.0)kΩ
3.8
(10.9)kΩ
(13.0)kΩ
(15.6)kΩ
(18.7)kΩ
(22.6)kΩ
(27.6)kΩ
(34.2)kΩ
(43.6)kΩ
(57.6)kΩ
(80.9)kΩ
(128.0)kΩ
(268.0)kΩ
0.2kΩ
3.9
4.01.7k
4.1
1.4kΩ
1.2kΩ
1.0kΩ
4.2
4.3
4.4
4.5
4.6
4.7
4.8
94.8kΩ
41.1kΩ
23.1kΩ
14.2kΩ
Ω
4.9
5.0
5.1
88.4kΩ
41.7kΩ
26.1kΩ
18.4kΩ
13.7kΩ
10.6kΩ
8.4kΩ
6.7kΩ
5.4kΩ
Ω
5.2
5.3
5.2kΩ
2.7kΩ
0.7kΩ
5.4
5.5
5.6
5.7
5.8
5.9
6.04.4k
6.1
3.5kΩ
2.8kΩ
2.2kΩ
1.7kΩ
1.2kΩ
42.3kΩ
Ω
6.2
6.3
5.6kΩ
Ω
6.4
6.5
R1 = (Blue)
R2 = Black
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
相关型号:
PT6683R
5A SWITCHING REGULATOR, 600kHz SWITCHING FREQ-MAX, SMA14, ROHS COMPLIANT, VERTICAL MOUNT PACKAGE-14
TI
©2020 ICPDF网 联系我们和版权申明