REG71050DRVTG4 [TI]
60mA, 5.0V, Buck/Boost Charge Pump in ThinSOT-23 and ThinQFN; 60毫安, 5.0V ,降压/升压充电泵采用ThinSOT -23和ThinQFN型号: | REG71050DRVTG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | 60mA, 5.0V, Buck/Boost Charge Pump in ThinSOT-23 and ThinQFN |
文件: | 总26页 (文件大小:1022K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
REG710
www.ti.com........................................................................................................................................... SBAS221G–DECEMBER 2001–REVISED JANUARY 2009
60mA, 5.0V, Buck/Boost Charge Pump
in ThinSOT-23 and ThinQFN
1
FEATURES
DESCRIPTION
2
•
Wide Input Range: 1.8V to 5.5V
Automatic Step-Up/Step-Down Operation
Low Input Current Ripple
The REG710 is
a switched capacitor voltage
converter that produces a regulated, low-ripple output
voltage from an unregulated input voltage. A wide
input supply voltage of 1.8V to 5.5V makes the
REG710 ideal for a variety of battery sources, such
as single-cell Li-Ion, or two- and three-cell nickel- or
alkaline-based chemistries.
•
•
•
•
Low Output Voltage Ripple
Minimum Number of External
Components—No Inductors
•
1MHz Internal Oscillator Allows Small
Capacitors
The input voltage may vary above and below the
output voltage and the output remains in regulation. It
works equally well for step-up or step-down
applications without the need for an inductor,
providing low EMI dc/dc conversion. The high
switching frequency allows the use of small
surface-mount capacitors, saving board space and
reducing cost. The REG710 is thermally protected
and current limited, protecting the load and the
regulator during fault conditions. Typical ground pin
current (quiescent current) is 65µA with no load, and
less than 1µA in shutdown mode.
•
•
•
Shutdown Mode
Thermal and Current Limit Protection
Six Output Voltages Available:
–
5.5V, 5.0V, 3.3V, 3.0V, 2.7V, 2.5V
•
Small Packages:
–
–
–
SOT23-6
TSOT23-6 (REG71055 and REG71050 Only)
TQFN-6 (2×2×0.8mm; REG71050 Only)
CPUMP
•
Evaluation Modules Available:
REG710EVM-33, REG710EVM-5
0.22mF
–
Enable
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Smart Card Readers
SIM Card Supplies
Cellular Phones
Portable Communication Devices
Personal Digital Assistants
Notebook and Palm-Top Computers
Modems
Electronic Games
Handheld Meters
PCMCIA Cards
Card Buses
REG71050
REG710-5
3.3V to
R
R
R
4.2V
CIN
COUT
2.2mF
2.2mF
GND
LED
LED
LED
REG710 Used in White LED Backlight Application
White LED Drivers
LCD Displays
Battery Backup Supplies
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2001–2009, Texas Instruments Incorporated
REG710
SBAS221G–DECEMBER 2001–REVISED JANUARY 2009........................................................................................................................................... www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
SPECIFIED
OUTPUT
VOLTAGE PACKAGE-LEAD
PACKAGE
DESIGNATOR
TEMPERATURE
RANGE
PACKAGE
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
MARKING(2)
5.5V Output
REG71055DDCT
REG71055DDCR
Tape and Reel, 250
REG71055DDC
5V Output
5.5V
TSOT23-6
DDC
–40°C to +85°C
R10H
Tape and Reel,
3000
REG710NA-5/250
REG710NA−5/3K
REG71050DDCT
REG71050DDCR
REG71050DRVT
REG71050DRVR
Tape and Reel, 250
REG710NA-5
5.0V
5.0V
5.0V
SOT23-6
TSOT23-6
TQFN-6
DBV
DDC
DRV
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
R10B
GAAI
CFF
Tape and Reel,
3000
Tape and Reel, 250
REG71050DDC
Tape and Reel,
3000
Tape and Reel, 250
REG71050DRV
3.3V Output
REG710NA-3.3
3V Output
Tape and Reel,
3000
REG710NA-3.3/250
REG710NA-3.3/3K
Tape and Reel, 250
3.3V
3.0V
2.7V
2.5V
SOT23-6
SOT23-6
SOT23-6
SOT23-6
DBV
DBV
DBV
DBV
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
R10C
R10D
R10F
R10G
Tape and Reel,
3000
REG710NA-3/250
REG710NA-3/3K
Tape and Reel, 250
REG710NA-3
2.7V Output
REG710NA-2.7
2.5V Output
REG710NA-2.5
Tape and Reel,
3000
REG710NA-2.7/250
REG710NA-2.7/3K
Tape and Reel, 250
Tape and Reel,
3000
REG710NA-2.5/250
REG710NA-2.5/3K
Tape and Reel, 250
Tape and Reel,
3000
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) Voltage is marked on reel. Add on row with the following data: Product: REG71050DRV Output Voltage: 5.0V Package-Lead: TQFN
Package Designator: DRV Specified Temp range: -40C to +85C Package marking: CFF Ordering Number: REG71050DRVT (Tape and
Reel, 250) REG71050DRVR (Tape and Reel, 3000)
ABSOLUTE MAXIMUM RATINGS(1)
REG710
–0.3 to +6.0
–0.3 to VIN
UNIT
V
Supply voltage
Enable input
V
Output short-circuit duration
Operating temperature range
Storage temperature range
Junction temperature
Indefinite
–55 to +125
–65 to +150
–55 to +150
+260
°C
°C
°C
°C
Lead temperature (soldering, 10s)
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
2
Submit Documentation Feedback
Copyright © 2001–2009, Texas Instruments Incorporated
Product Folder Link(s): REG710
REG710
www.ti.com........................................................................................................................................... SBAS221G–DECEMBER 2001–REVISED JANUARY 2009
PIN CONFIGURATIONS
TSOT23/SOT23
(TOP VIEW)
1
2
3
6
5
4
CPUMP+
VIN
VOUT
GND
CPUMP-
Enable
TQFN
(TOP VIEW)
1
2
3
6
5
4
CPUMP+
VIN
VOUT
Enable
GND
CPUMP-
SIMPLIFIED BLOCK DIAGRAM
CPUMP
0.22mF
4
6
5
VIN
REG710
CIN
2.2mF
1
VOUT
COUT
2.2mF
Control
&
3
Enable
Thermal
2
GND
Copyright © 2001–2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): REG710
REG710
SBAS221G–DECEMBER 2001–REVISED JANUARY 2009........................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
At TA = +25°C, VIN = VOUT/2 + 0.75V, IOUT = 10mA, CIN = COUT = 2.2µF, CPUMP = 0.22µF, and VENABLE = 1.3V, unless otherwise
noted.
REG710
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT VOLTAGE
Tested Startup
REG71055
See conditions under Output Voltage with a
resistive load no lower than typical
3.0
2.7
1.8
5.5
5.5
5.5
V
V
V
REG710-5
VOUT/IOUT
.
All other models
OUTPUT VOLTAGE
REG71055
IOUT ≤ 10mA, 3.0V ≤ VIN ≤ 5.5V
5.2
5.2
5.5
5.5
5.0
5.0
5.0
3.3
3.3
3.0
3.0
2.7
2.7
2.5
2.5
5.8
5.8
V
V
V
V
V
V
V
V
V
V
V
V
V
IOUT ≤ 30mA, 3.25V ≤ VIN ≤ 5.5V
REG710-5, REG71050
IOUT ≤ 10mA, 2.7V ≤ VIN ≤ 5.5V
IOUT ≤ 30mA, 3.0V ≤ VIN ≤ 5.5V
IOUT ≤ 60mA, 3.3V ≤ VIN ≤ 4.2V
IOUT ≤ 10mA, 1.8V ≤ VIN ≤ 5.5V
IOUT ≤ 30mA, 2.2V ≤ VIN ≤ 5.5V
IOUT ≤ 10mA, 1.8V ≤ VIN ≤ 5.5V
IOUT ≤ 30mA, 2.2V ≤ VIN ≤ 5.5V
IOUT ≤ 10mA, 1.8V ≤ VIN ≤ 5.5V
IOUT ≤ 30mA, 2.0V ≤ VIN ≤ 5.5V
IOUT ≤ 10mA, 1.8V ≤ VIN ≤ 5.5V
IOUT ≤ 30mA, 2.0V ≤ VIN ≤ 5.5V
4.7
5.3
4.7
5.3
4.6
5.4
REG710-3.3
REG710-3
3.10
3.10
2.82
2.82
2.54
2.54
2.35
2.35
3.50
3.50
3.18
3.18
2.86
2.86
2.65
2.65
REG710-2.7
REG710-2.5
OUTPUT CURRENT
Nominal
Short-circuit(1)
OSCILLATOR FREQUENCY(2)
EFFICIENCY(3)
RIPPLE VOLTAGE(4)
ENABLE CONTROL
Logic high input voltage
Logic low input voltage
Logic high input current
Logic low input current
THERMAL SHUTDOWN
Shutdown temperature
Shutdown recovery
30
mA
mA
100
1.0
90
MHz
%
IOUT = 10mA, VIN = 1.8V, REG710-3.3
IOUT = 30mA
35
mVPP
VIN = 1.8V to 5.5V
1.3
VIN
0.4
V
V
–0.2
100
100
nA
nA
160
140
°C
°C
SUPPLY CURRENT
(Quiescent current)
IOUT = 0mA
65
100
1
µA
µA
In shutdown mode
VIN = 1.8V to 5.5V, Enable = 0V
0.01
TEMPERATURE RANGE
Specified ambient temperature
Operating ambient temperature
Storage ambient temperature
Thermal resistance
TA
TA
–40
–55
–65
+85
+125
+150
°C
°C
TA
°C
θJA
SOT23-6
TSOT23-6
TQFN-6
200
220
75
°C/W
°C/W
°C/W
(1) The supply current is twice the output short-circuit current.
(2) The converter regulates by enabling and disabling periods of switching cycles. The switching frequency is the oscillator frequency during
an active period.
(3) See efficiency curves for other VIN/VOUT configurations.
(4) Effective series resistance (ESR) of capacitors is < 0.1Ω.
4
Submit Documentation Feedback
Copyright © 2001–2009, Texas Instruments Incorporated
Product Folder Link(s): REG710
REG710
www.ti.com........................................................................................................................................... SBAS221G–DECEMBER 2001–REVISED JANUARY 2009
TYPICAL CHARACTERISTICS
At TA = +25°C, VIN = VOUT/2 + 0.75V, IOUT = 5mA, CIN = COUT = 2.2µF, CPUMP = 0.22µF, and VENABLE = 1.3V, unless otherwise
noted.
EFFICIENCY vs LOAD CURRENT
EFFICIENCY vs VIN
(REG710-5V, REG71050)
90
80
70
60
50
40
30
90
80
70
60
50
40
30
REG710-5, REG71050
REG71055
VIN = 2.7V
VIN = 3V
REG710-3.3
REG710-3
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = VOUT
REG710-2.5
REG710-2.7
0.1
1
10
Load Current (mA)
100
1.5
2.0
2.5
3.5
VIN (V)
4.0
4.5
5.0
5.5
3.0
Figure 1.
Figure 2.
EFFICIENCY vs LOAD CURRENT
(REG710-3.3V)
EFFICIENCY vs LOAD CURRENT
(REG710-3V)
90
80
70
60
50
40
30
90
80
70
60
50
40
30
VIN = 1.8V
VIN = 1.8V
VIN = 2.2V
VIN = 2.2V
VIN = VOUT
VIN = VOUT
0.1
1
10
Load Current (mA)
Figure 3.
100
0.1
1
10
100
Load Current (mA)
Figure 4.
EFFICIENCY vs LOAD CURRENT
(REG710-2.7V)
EFFICIENCY vs LOAD CURRENT
(REG710-2.5V)
80
75
70
65
60
55
50
45
40
35
30
80
75
70
65
60
55
50
45
40
35
30
VIN = 1.8V
VIN = 1.8V
VIN = 2.2V
VIN = 2.2V
VIN = VOUT
VIN = VOUT
0.1
1
10
Load Current (mA)
Figure 5.
100
0.1
1
10
Load Current (mA)
Figure 6.
100
Copyright © 2001–2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): REG710
REG710
SBAS221G–DECEMBER 2001–REVISED JANUARY 2009........................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VIN = VOUT/2 + 0.75V, IOUT = 5mA, CIN = COUT = 2.2µF, CPUMP = 0.22µF, and VENABLE = 1.3V, unless otherwise
noted.
SUPPLY CURRENT vs TEMPERATURE
(No Load)
LOAD TRANSIENT RESPONSE
100
80
60
40
20
0
20mV/div
VOUT
10mA/div
ILOAD
BW = 20MHz
Time (10ms/div)
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90
Temperature (°C)
Figure 7.
Figure 8.
SUPPLY CURRENT vs TEMPERATURE
(Not Enabled)
LINE TRANSIENT RESPONSE
20
18
16
14
12
10
8
REG710-3.3V
RL = 110W
Buck Mode
4.5V
3.5V
VIN
Boost Mode
2V/div
6
50mV/div
VOUT
4
2
BW = 20MHz
Time (50ms/div)
0
-10
-40 -30 -20
0
10 20 30 40 50 60 70 80 90
Temperature (°C)
Figure 9.
Figure 10.
OUTPUT VOLTAGE vs TEMPERATURE
OUTPUT VOLTAGE DRIFT HISTOGRAM
0.2
0.1
25
20
15
10
5
0.0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
0
20
-40 -20
0
40
60
80
100 120 140
Junction Temperature (°C)
VOUT Drift (ppm/°C)
Figure 11.
Figure 12.
6
Submit Documentation Feedback
Copyright © 2001–2009, Texas Instruments Incorporated
Product Folder Link(s): REG710
REG710
www.ti.com........................................................................................................................................... SBAS221G–DECEMBER 2001–REVISED JANUARY 2009
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VIN = VOUT/2 + 0.75V, IOUT = 5mA, CIN = COUT = 2.2µF, CPUMP = 0.22µF, and VENABLE = 1.3V, unless otherwise
noted.
OUTPUT RIPPLE VOLTAGE
SHORT-CIRCUIT LOAD CURRENT vs VIN
250
225
200
175
150
125
100
75
COUT = 2.2mF
20mV/div
COUT = 10mF, CPUMP = 1mF
20mV/div
REG710-3.3V
VIN = 2.4V
50
25
RL = 332W
BW = 20MHz
0
Time (5ms/div)
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
Figure 13.
Figure 14.
OUTPUT RIPPLE VOLTAGE vs VIN
(REG710-2.7V, 3.3V)
INPUT CURRENT AT TURN-ON
90
80
70
60
50
40
30
20
10
0
REG710-2.7
COUT = 2.2mF
100mA/div
IIN
REG710-3.3
REG710-2.7
VOUT
COUT = 2.2mF
COUT = 10mF
2V/div
REG710-3.3V
VIN = 3.0V
REG710-3.3
BW = 20MHz
IO = 30mA
COUT = 10mF
Time (50ms/div)
4.5 5.0 5.5
1.0 1.5 2.0 2.5 3.0 3.5 4.0
VIN (V)
6.0
Figure 15.
Figure 16.
OUTPUT RIPPLE VOLTAGE vs VIN
(REG710-2.5V, 3V, 5V)
90
REG710-3
80
70
60
50
40
30
20
10
0
COUT = 2.2mF
REG710-5
REG71050
REG710-2.5
COUT = 2.2mF
COUT = 2.2mF
REG710-5
REG71050
COUT = 10mF
REG710-3
COUT = 10mF
REG710-2.5, COUT = 10mF
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VIN (V)
Figure 17.
Copyright © 2001–2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): REG710
REG710
SBAS221G–DECEMBER 2001–REVISED JANUARY 2009........................................................................................................................................... www.ti.com
THEORY OF OPERATION
During the second half cycle the FET switched are
configured as shown in Figure 19B, and the voltage
on CPUMP is added to VIN. The output voltage is
regulated by skipping clock cycles as necessary.
The REG710 regulated charge pump provides a
regulated output voltage for input voltages ranging
from less than the output to greater than the output.
This is accomplished by automatic mode switching
within the device. When the input voltage is greater
than the required output, the unit functions as a
PEAK CURRENT REDUCTION
variable frequency switch-mode regulator. This
operation is shown in Figure 18. Transistors Q1 and
Q3 are held off, Q4 is on, and Q2 is switched as
needed to maintain a regulated output voltage.
In normal operation, the charging of the pump and
output capacitors usually leads to relatively high peak
input currents which can be much higher than that of
the average load current. The regulator incorporates
circuitry to limit the input peak current, lowering the
total EMI production of the device and lowering
output voltage ripple and input current ripple. Input
capacitor (CIN) supplies most of the charge required
by input current peaks.
When the input voltage is less than the required
output voltage, the device switches to a step-up or
boost mode of operation, as shown in Figure 19.
A conversion clock of 50% duty cycle is generated.
During the first half cycle the FET switches are
configured as shown in Figure 19A, and CPUMP
charges to VIN.
VIN
Q1
Q2
OFF
SWITCHED
CPUMP
Q3
Q4
OFF
ON
CIN
VOUT
COUT
Step-Down (Buck) Mode
Figure 18. Simplified Schematic of the REG710 Operating in the Step-Down Mode
VIN
VIN
Q2
Q2
Q1
Q1
OFF
ON
ON
ON
OFF
CPUMP
CPUMP
Q3
Q4
Q3
Q4
OFF
ON
OFF
CIN
CIN
VOUT
VOUT
COUT
COUT
Step-Up (Boost) Mode
(A)
(B)
Figure 19. Simplified Schematic of the REG710 Operating in the Step-Up or Boost Mode
8
Submit Documentation Feedback
Copyright © 2001–2009, Texas Instruments Incorporated
Product Folder Link(s): REG710
REG710
www.ti.com........................................................................................................................................... SBAS221G–DECEMBER 2001–REVISED JANUARY 2009
PROTECTION
pump capacitors (CIN and CPUMP, respectively) should
also be surface-mount ceramic types. In all cases,
X7R or X5R dielectric are recommended. See the
typical operating circuit shown in Figure 20 for
component values.
The regulator has thermal shutdown circuitry that
protects it from damage caused by overload
conditions. The thermal protection circuitry disables
the output when the junction temperature reaches
approximately +160°C, allowing the device to cool.
CPUMP
When
the
junction
temperature
cools
to
0.22mF
approximately +140°C, the output circuitry is
automatically reenabled. Continuously running the
regulator into thermal shutdown can degrade
reliability. The regulator also provides current limit to
protect itself and the load.
4
6
Enable
3
5
1
VIN
VOUT
REG710
COUT
CIN
2.2mF
2.2mF
SHUTDOWN MODE
GND
2
The EN pin enables the IC when pulled high and
places it into energy-saving shutdown mode when
pulled low. When in shutdown mode, the output is
disconnected from the input and the quiescent current
is reduced to 0.01µA typical. This shutdown mode
functionality is only valid when VIN is above the
minimum recommended operating voltage. The EN
pin cannot be left floating and must be actively
terminated either high or low.
Figure 20. Typical Operating Circuit
With light loads or higher input voltage, a smaller
0.1µF pump capacitor (CPUMP) and smaller 1µF input
and output capacitors (CIN and COUT, respectively)
can be used. To minimize output voltage ripple,
increase the output capacitor, COUT, to 10µF or
larger.
CAPACITOR SELECTION
For minimum output voltage ripple, the output
capacitor COUT should be a ceramic, surface-mount
type. Tantalum capacitors generally have a higher
effective series resistance (ESR) and may contribute
to higher output voltage ripple. Leaded capacitors
also increase ripple due to the higher inductance of
the package itself. To achieve best operation with low
input voltage and high load current, the input and
The capacitors listed in Table 1 can be used with the
REG710. This table is only a representative list of
compatible parts.
Table 1. Suggested Capacitors
RATED
DIELECTRIC
MATERIAL
PACKAGE
SIZE
WORKING
VOLTAGE
MANUFACTURER
PART NUMBER
C1206C255K8RAC
C1206C224K8RAC
ECJ−2YBOJ225K
ECJ−2VBIC224K
ECJ−2VBIC104
VALUE
2.2µF
TOLERANCE
±10%
X7R
X7R
X5R
X7R
X7R
X7R
X7R
1206
1206
805
10V
10V
6.3V
16V
16V
16V
25V
Kemet
0.22µF
2.2µF
±10%
±10%
Panasonic
0.22µF
0.1µF
±10%
805
±10%
805
EMK316BJ225KL
TKM316BJ224KF
2.2µF
±10%
1206
1206
Taiyo Yuden
0.22µF
±10%
Copyright © 2001–2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): REG710
REG710
SBAS221G–DECEMBER 2001–REVISED JANUARY 2009........................................................................................................................................... www.ti.com
EFFICIENCY
LAYOUT
The efficiency of the charge pump regulator varies
with the output voltage version, the applied input
voltage, the load current, and the internal operation
mode of the device.
Large transient currents flow in the VIN, VOUT, and
GND traces. To minimize both input and output
ripple, keep the capacitors as close as possible to the
regulator using short, direct circuit traces.
The approximate efficiency is given by:
A suggested printed circuit board (PCB) routing is
shown in Figure 21. The trace lengths from the input
and output capacitors have been kept as short as
possible.
Efficiency (%) = VOUT/(2 ´ VIN) ´ 100
(step-up operating mode)
or
VENABLE
AREA: < 0.08 sq. inches
VOUT
VOUT
´ 100
VIN
VIN
(step-down operating mode)
COUT
Table 2 lists the approximate values of the input
voltage at which the device changes internal
operating mode. See efficiency curves in the Typical
Characteristics section for various loads and input
voltages.
CIN
CP
GND
Figure 21. Suggested PCB Design for Minimum
Ripple
Table 2. Operating Mode Change versus VIN
OPERATING MODE
PRODUCT
REG710-2.5
REG710-2.7
REG710-3
CHANGES AT VIN OF
> 3.2V
> 3.4V
> 3.7V
> 4.0V
REG710-3.3
REG710-5, REG71050,
REG71055
Step-up only
10
Submit Documentation Feedback
Copyright © 2001–2009, Texas Instruments Incorporated
Product Folder Link(s): REG710
REG710
www.ti.com........................................................................................................................................... SBAS221G–DECEMBER 2001–REVISED JANUARY 2009
APPLICATION CIRCUITS
0.22mF
0.22mF
CP1
CP2
3.3V
3.0V
5.0V
1.8V
VIN
VOUT
VIN
VOUT
REG710-3.3
REG710-3
REG71050
REG710-5
2.2mF
2.2mF
+
2.2mF
VIN
CIN
COUT
-
EN
GND
EN
GND
Figure 22. REG710 Circuit for Step-Up Operation from 1.8V to 5.0V with 10mA Output Current
0.22mF
CP1
VIN
VOUT
VOUT
REG710-3.3
+
4.7mF
4.7mF
COUT
VIN
CIN
GND
-
0.22mF
CP2
VIN
VOUT
REG710-3.3
GND
Figure 23. REG710 Circuit for Doubling the Output Current
CPUMP
0.22mF
Enable
REG71050
REG710-5
3.3V to
4.2V
R
R
R
CIN
COUT
2.2mF
2.2mF
GND
LED
LED
LED
Figure 24. REG710 Circuit for Driving LEDs
Copyright © 2001–2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): REG710
REG710
SBAS221G–DECEMBER 2001–REVISED JANUARY 2009........................................................................................................................................... www.ti.com
0.22mF
C-
VIN
C+
VOUT
3.3V
V
IN £ VOUT
IL
REG710-3.3
2.2mF
2.2mF
EN
GND
RL
2.2mF
74HC04
5818
5818
-2.7V at 1mA
when IL = 10mA
2.2mF
Figure 25. REG710 with Negative Bias Supply
12
Submit Documentation Feedback
Copyright © 2001–2009, Texas Instruments Incorporated
Product Folder Link(s): REG710
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
REG71050DDCR
REG71050DDCRG4
REG71050DDCT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOT
SOT
DDC
DDC
DDC
DDC
DRV
DRV
DRV
DRV
DDC
DDC
DDC
DDC
DBV
DBV
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3000
3000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
SOT
Green (RoHS
& no Sb/Br)
REG71050DDCTG4
REG71050DRVR
SOT
250
Green (RoHS
& no Sb/Br)
SON
SON
SON
SON
SOT
3000
3000
250
Green (RoHS
& no Sb/Br)
REG71050DRVRG4
REG71050DRVT
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
REG71050DRVTG4
REG71055DDCR
250
Green (RoHS
& no Sb/Br)
3000
3000
250
Green (RoHS
& no Sb/Br)
REG71055DDCRG4
REG71055DDCT
SOT
Green (RoHS
& no Sb/Br)
SOT
Green (RoHS
& no Sb/Br)
REG71055DDCTG4
REG710NA-2.5/250
REG710NA-2.5/250G4
SOT
250
Green (RoHS
& no Sb/Br)
SOT-23
SOT-23
250
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
REG710NA-2.5/3K
REG710NA-2.5/3KG4
REG710NA-2.7/250
ACTIVE
ACTIVE
ACTIVE
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
6
6
6
TBD
TBD
Call TI
Call TI
Call TI
Call TI
250
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
REG710NA-2.7/250G4
ACTIVE
SOT-23
DBV
6
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
REG710NA-3.3/250
REG710NA-3.3/250G4
REG710NA-3.3/3K
REG710NA-3.3/3KG4
REG710NA-3/250
REG710NA-3/250G4
REG710NA-3/3K
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
6
6
6
6
6
6
6
6
6
6
6
6
250
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
3000
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
3000
3000
250
Green (RoHS
& no Sb/Br)
REG710NA-3/3KG4
REG710NA-5/250
REG710NA-5/250G4
REG710NA-5/3K
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
3000
3000
Green (RoHS
& no Sb/Br)
REG710NA-5/3KG4
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF REG71055 :
Automotive: REG71055-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
REG71050DDCR
REG71050DDCT
REG71050DRVR
REG71050DRVR
REG71050DRVT
REG71050DRVT
REG71055DDCR
REG71055DDCT
REG710NA-2.5/250
REG710NA-2.7/250
REG710NA-3.3/250
REG710NA-3.3/3K
REG710NA-3/250
REG710NA-3/3K
REG710NA-5/250
REG710NA-5/3K
REG710NA-5/3K
SOT
SOT
DDC
DDC
DRV
DRV
DRV
DRV
DDC
DDC
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3000
250
179.0
179.0
180.0
179.0
180.0
179.0
179.0
179.0
179.0
179.0
178.0
178.0
179.0
179.0
178.0
178.0
179.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
9.0
9.0
8.4
8.4
9.0
9.0
8.4
3.2
3.2
3.2
3.2
1.4
1.4
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q3
Q3
Q2
Q2
Q2
Q2
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
SON
3000
3000
250
2.3
2.3
1.15
1.2
SON
2.2
2.2
SON
2.3
2.3
1.15
1.2
SON
250
2.2
2.2
SOT
3000
250
3.2
3.2
1.4
SOT
3.2
3.2
1.4
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
250
3.2
3.2
1.4
250
3.2
3.2
1.4
250
3.23
3.23
3.2
3.17
3.17
3.2
1.37
1.37
1.4
3000
250
3000
250
3.2
3.2
1.4
3.23
3.23
3.2
3.17
3.17
3.2
1.37
1.37
1.4
3000
3000
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Aug-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
REG71050DDCR
REG71050DDCT
REG71050DRVR
REG71050DRVR
REG71050DRVT
REG71050DRVT
REG71055DDCR
REG71055DDCT
REG710NA-2.5/250
REG710NA-2.7/250
REG710NA-3.3/250
REG710NA-3.3/3K
REG710NA-3/250
REG710NA-3/3K
REG710NA-5/250
REG710NA-5/3K
REG710NA-5/3K
SOT
SOT
DDC
DDC
DRV
DRV
DRV
DRV
DDC
DDC
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3000
250
203.0
203.0
210.0
195.0
210.0
195.0
203.0
203.0
203.0
203.0
180.0
180.0
203.0
203.0
180.0
180.0
203.0
203.0
203.0
185.0
200.0
185.0
200.0
203.0
203.0
203.0
203.0
180.0
180.0
203.0
203.0
180.0
180.0
203.0
35.0
35.0
35.0
45.0
35.0
45.0
35.0
35.0
35.0
35.0
18.0
18.0
35.0
35.0
18.0
18.0
35.0
SON
3000
3000
250
SON
SON
SON
250
SOT
3000
250
SOT
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
250
250
250
3000
250
3000
250
3000
3000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明