SN65HVD1781AQDRQ1 [TI]
具有故障保护功能和 3.3V 至 5V 工作电压的汽车类 RS-485 收发器 | D | 8 | -40 to 125;型号: | SN65HVD1781AQDRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有故障保护功能和 3.3V 至 5V 工作电压的汽车类 RS-485 收发器 | D | 8 | -40 to 125 PC 驱动 光电二极管 接口集成电路 驱动器 |
文件: | 总26页 (文件大小:1493K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
SN65HVD1781A-Q1 故障保护RS-485 收发器(3.3V 至5V 工作电压)
1 特性
3 说明
• 符合汽车应用要求
• 具有符合AEC-Q100 标准的下列特性
该器件被设计成在遇到过压故障(例如电源直接短路、
误接线故障、连接器故障、电缆挤压以及工具误用)时
免受损坏。它还具有高级的人体放电模型保护规格,在
静电放电(ESD) 事件发生时依然可保持稳定。
– 器件温度等级1:
-40°C 至125°C 环境工作温度范围
– 器件HBM ESD 分类等级H2
– 器件CDM ESG 分类等级C3B
• 提供功能安全
SN65HVD1781A-Q1 将一个差动驱动器和一个差动接
收器组合在一起,这两个器件由单个电源供电。驱动器
差动输出和接收器差动输入在内部进行连接,形成适用
于半双工(双线总线)通信的总线端口。此端口特有一
个宽共模电压范围,因此适合于长线缆运行上的多点应
用。该器件的温度范围是 -40°C 至 125°C 。
SN65HVD1781A-Q1 器件与业界通用的 SN75176 收
发器引脚兼容,因此该器件适合大多数系统用于进行升
级。
– 有助于进行功能安全系统设计的文档
• 总线引脚故障保护:> ±70V
• 3.3V 至5V 的工作电源电压范围
• 总线引脚上的±16kV HBM 保护
• 减少高达320 个节点的单位负载
• 针对开路、短路和空闲总线情况的失效防护接收器
• 低功耗
该器件采用 5V 电源时完全符合 ANSI TIA/EIA 485-
A,并且可以使用 3.3V 电源运行,同时降低驱动器输
出电压,以适用于低功耗应用。对于需要在扩展共模电
压范围内运行的应用, 请参阅 SN65HVD1785
(SLLS872) 数据表。
– 低待机电源电流:1μA(最大值)
– 运行期间ICC 4mA 静态电流
• 与业界通用的SN75176 引脚兼容
• 信号传输速率高达1Mbps
2 应用
器件信息
封装(1)
• 信息娱乐系统,仪表组
• HMI 和显示屏
• 媒体接口
封装尺寸(标称值)
器件型号
SN65HVD1781A-Q1 SOIC
4.90mm x 3.91mm
• 音响主机
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
VFAULT up to 70 V
Copyright © 2016, Texas Instruments Incorporated
简化版原理图
本文档旨在为方便起见,提供有关TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLLSF08
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
Table of Contents
8.2 Functional Block Diagram.........................................13
8.3 Feature Description...................................................13
8.4 Device Functional Modes..........................................14
9 Application and Implementation..................................15
9.1 Application Information............................................. 15
9.2 Typical Application.................................................... 15
10 Power Supply Recommendations..............................19
11 Layout...........................................................................20
11.1 Layout Guidelines................................................... 20
11.2 Layout Example...................................................... 20
12 Device and Documentation Support..........................21
12.1 Device Support....................................................... 21
12.2 Documentation Support.......................................... 21
12.3 Receiving Notification of Documentation Updates..21
12.4 Community Resources............................................21
12.5 Trademarks.............................................................21
13 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings—AEC.................................................... 4
6.3 ESD Ratings—IEC......................................................4
6.4 Recommended Operating Conditions.........................4
6.5 Thermal Information....................................................5
6.6 Electrical Characteristics.............................................6
6.7 Power Dissipation Ratings..........................................7
6.8 Switching Characteristics............................................7
6.9 Typical Characteristics................................................8
7 Parameter Measurement Information............................9
8 Detailed Description......................................................13
8.1 Overview...................................................................13
Information.................................................................... 21
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision * (May 2017) to Revision A (February 2022)
Page
• 添加了特性“提供功能安全”.............................................................................................................................1
Copyright © 2022 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
5 Pin Configuration and Functions
R
RE
DE
D
1
2
3
4
8
7
6
5
V
ꢀ
CC
B
A
GND
图5-1. D (SOIC) Package, 8-Pin, Top View
表5-1. Pin Functions
PIN
TYPE
DESCRIPTION
NAME
NO.
6
A
Bus I/O
Bus I/O
Driver output or receiver input (complementary to B)
Driver output or receiver input (complementary to A)
B
7
D
4
Digital input Driver data input
DE
3
Digital input Driver enable, active high
Reference
GND
5
Local device ground
potential
R
1
2
8
Digital output Receive data output
RE
VCC
Digital input Receiver enable, active low
Supply
3.15-V-to-5.5-V supply
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
6 Specifications
6.1 Absolute Maximum Ratings
See Note (1)
.
MIN
–0.5
–70
–0.3
–70
–24
MAX
UNIT
V
VCC Supply voltage
Voltage range at bus pins
Input voltage range at any logic pin
7
70
A, B pins
V
VCC + 0.3
70
V
V
Transient overvoltage pulse through 100 Ω per TIA-485
Receiver output current
24
mA
Continuous total power dissipation
Junction temperature
See 节6.7
TJ
170
150
°C
°C
Tstg Storage temperature
–40
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings—AEC
VALUE
±16000
±4000
±1500
UNIT
Bus terminals and GND
All pins
Human-body model (HBM), per AEC Q100-002(1)
Charged-device model (CDM), per AEC Q100-011
Electrostatic
discharge
V(ESD)
V
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 ESD Ratings—IEC
VALUE
UNIT
Electrostatic
discharge
V(ESD)
Human body model (HBM), per IEC 60749-26
Bus terminals and GND
±16000
V
6.4 Recommended Operating Conditions
MIN
3.15
–7
2
NOM
MAX
5.5
12
UNIT
VCC
VI
Supply voltage
5
V
V
Input voltage at any bus terminal (separately or common mode)(1)
High-level input voltage (driver, driver enable, and receiver enable inputs)
Low-level input voltage (driver, driver enable, and receiver enable inputs)
Differential input voltage
VIH
VIL
VID
VCC
0.8
12
V
0
V
V
–12
–60
–8
54
Output current, driver
60
mA
mA
IO
Output current, receiver
8
RL
Differential load resistance
60
50
Ω
pF
CL
Differential load capacitance
1/tUI
Signaling rate
1
105
125
150
Mbps
5-V supply
–40
–40
–40
Operating free-air temperature (See the 节
6.5 table)
TA
TJ
°C
°C
3.3-V supply
Junction Temperature
(1) By convention, the least positive (most negative) limit is designated as minimum in this data sheet.
Copyright © 2022 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
6.5 Thermal Information
SN65HVD1781A-Q1
THERMAL METRIC(1)
D (SOIC)
8 PINS
97.7
UNIT
JEDEC high-K model
JEDEC low-K model
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJA
Junction-to-ambient thermal resistance
242
RθJC(top) Junction-to-case (top) thermal resistance
39.6
RθJB
ψJT
Junction-to-board thermal resistance
39.2
Junction-to-top characterization parameter
Junction-to-board characterization parameter
3.8
38.5
ψJB
RθJC(bot) Junction-to-case (bottom) thermal resistance
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
6.6 Electrical Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TA < 85°C
1.5
RL = 60 Ω, 4.75 V ≤VCC 375 Ω
on each output to –7 V to 12 V, See 图
7-1
TA < 125°C
1.4
TA < 85°C
1.7
1.5
2
RL = 54 Ω,
4.75 V ≤VCC ≤5.25 V
TA < 125°C
|VOD
|
Driver differential output voltage magnitude
V
RL = 54 Ω,
3.15 V ≤VCC ≤3.45 V
0.8
1
TA < 85°C
2.2
2
2.5
RL = 100 Ω,
4.75 V ≤VCC ≤5.25 V
TA < 125°C
Change in magnitude of driver differential
output voltage
0
VCC/2
0
50
3
mV
V
Δ|VOD
|
RL = 54 Ω
–50
1
VOC(SS)
Steady-state common-mode output voltage
Change in differential driver output common-
mode voltage
50
mV
ΔVOC
–50
Peak-to-peak driver common-mode output
voltage
Center of two 27-Ωload resistors,
See 图7-2
VOC(PP)
COD
500
23
mV
pF
Differential output capacitance
Positive-going receiver differential input voltage
threshold
VIT+
mV
–100
–35
Negative-going receiver differential input
voltage threshold
VIT–
mV
mV
–180
30
–150
Receiver differential input voltage threshold
hysteresis
(VIT+ –VIT–
VHYS
50
(1)
)
VCC
–
VOH
Receiver high-level output voltage
Receiver low-level output voltage
2.4
V
V
IOH = –8 mA
0.3
TA < 85°C
0.2
0.4
0.5
VOL
IOL = 8 mA
TA < 125°C
Driver input, driver enable, and receiver enable
input current
II(LOGIC)
50
–50
μA
IOZ
IOS
Receiver output high-impedance current
Driver short-circuit output current
VO = 0 V or VCC, RE at VCC
1
200
100
–1
μA
mA
–200
VI = 12 V
75
VCC = 3.15 to 5.5 V or
VCC = 0 V, DE at 0 V
II(BUS)
Bus input current (disabled driver)
μA
VI = –7 V
–60
–40
DE = VCC, RE = GND,
no load
Driver and receiver enabled
4
3
2
6
5
4
Driver enabled, receiver
disabled
DE = VCC, RE = VCC
no load
,
mA
Driver disabled, receiver
enabled
DE = GND, RE = GND,
no load
ICC
Supply current (quiescent)
DE = GND, D = open,
RE = VCC, no load, TA
85°C
<
0.15
1
Driver and receiver disabled,
standby mode
μA
DE = GND, D = open,
RE = VCC, no load, TA
125°C
<
12
Supply current (dynamic)
See the 节6.9 section
(1) Ensured by design. Not production tested.
Copyright © 2022 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
6.7 Power Dissipation Ratings
PARAMETER
TEST CONDITIONS
VALUE
UNIT
VCC = 3.6 V, TJ = 150°C, RL = 300 Ω,
CL = 50 pF (driver), CL = 15 pF (receiver)
3.3-V supply, unterminated(1)
75
VCC = 3.6 V, TJ = 150°C, RL = 100 Ω,
CL = 50 pF (driver), CL = 15 pF (receiver)
3.3-V supply, RS-422 load(1)
95
VCC = 3.6 V, TJ = 150°C, RL = 54 Ω,
CL = 50 pF (driver), CL = 15 pF (receiver)
3.3-V supply, RS-485 load(1)
115
290
320
PD
Power dissipation
mW
VCC = 5.5 V, TJ = 150°C, RL = 300 Ω,
CL = 50 pF (driver), CL = 15 pF (receiver)
5-V supply, unterminated(1)
VCC = 5.5 V, TJ = 150°C, RL = 100 Ω,
CL = 50 pF (driver), CL = 15 pF (receiver)
5-V supply, RS-422 load(1)
VCC = 5.5 V, TJ = 150°C, RL = 54 Ω,
CL = 50 pF (driver), CL = 15 pF (receiver)
5-V supply, RS-485 load(1)
400
170
TSD Thermal-shutdown junction temperature
°C
(1) Driver and receiver enabled, 50% duty cycle square-wave signal at signaling rate: 1 Mbps.
6.8 Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
DRIVER
tr, tf
Driver differential output rise/fall time
Driver propagation delay
50
300
200
ns
ns
RL = 54 Ω, CL = 50 pF, See 图7-3
RL = 54 Ω, CL = 50 pF, See 图7-3
tPHL, tPLH
Driver differential output pulse skew,
tSK(P)
25
ns
RL = 54 Ω, CL = 50 pF, See 图7-3
|tPHL –tPLH
|
3
300
10
tPHZ, tPLZ
Driver disable time
See 图7-4 and 图7-5
μs
ns
Receiver enabled
tPZH, tPZL
Driver enable time
See 图7-4 and 图7-5
Receiver disabled
μs
RECEIVER
CL = 15 pF,
See 图7-6
4
15
tr, tf
Receiver output rise/fall time (1)
ns
ns
ns
CL = 15 pF,
See 图7-6
tPHL, tPLH
Receiver propagation delay time
Receiver output pulse skew,
100
6
200
20
CL = 15 pF,
See 图7-6
tSK(P)
|tPHL –tPLH
|
15
80
3
100
300
9
tPLZ, tPHZ
Receiver disable time (1)
ns
ns
Driver enabled, See 图7-7
Driver enabled, See 图7-7
Driver disabled, See 图7-8
tPZL(1), tPZH(1)
tPZL(2), tPZH(2)
Receiver enable time
μs
(1) Specified by design. Not production tested.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
6.9 Typical Characteristics
10
80
70
60
50
40
30
20
T
A
= 25°C
RE at V
DE at V
CC
0
−10
−20
−30
V
CC
= 5 V
CC
R
C
= 54 W
= 50 pF
L
L
V
CC
= 3.3 V
T
= 25°C
A
DE at V
CC
D at V
−40
−50
CC
R
= 54 W
L
0
1
2
3
4
5
6
0
100 200 300 400 500 600 700 800 900 1000
Signaling Rate − kbps
V
− Supply Voltage − V
CC
G002
G001
图6-2. RMS Supply Current vs Signaling Rate
图6-1. Driver Output Current vs Supply Voltage
4.4
35
4.0
30
V
= 5.5 V
CC
3.6
3.2
2.8
2.4
2.0
1.6
1.2
0.8
0.4
0.0
VCC = 3.3 V
25
20
Load = 300 W
Load = 100 W
Load = 60 W
15
VCC = 5 V
10
V
CC
= 3.3 V
5
0
V
CC
= 3.15 V
0
5
10 15 20 25 30 35 40 45 50
− Differential Load Current − mA
-50
0
50
100
150
I
(diff)
G003
Temperature - (°C)
图6-3. Differential Output Voltage vs Differential
图6-4. Rise and Fall Time
Load Current
2.5
R
C
= 50 W,
V
= 5.5 V
L
L
CC
2.3
2.1
1.9
= 50 pF
V
= 5 V
CC
1.7
1.5
1.3
1.1
0.9
V
= 4.5 V
CC
V
= 4 V
CC
V
= 3.6 V
CC
V
= 3.3 V
CC
V
= 3 V
CC
0.7
0.5
Transition Time − ns
图6-5. Differential Output Amplitude and Transition Time vs Supply Voltage
Copyright © 2022 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
7 Parameter Measurement Information
Input generator rate is 100 kbps, 50% duty cycle, rise and fall times less than 6 ns, output impedance 50 Ω.
375 W ±1%
VCC
DE
A
B
D
VOD
0 V or 3 V
60 W ±1%
+
_
–7 V < V(test) < 12 V
375 W ±1%
Copyright © 2016, Texas Instruments Incorporated
图7-1. Measurement of Driver Differential Output Voltage With Common-Mode Load
VCC
VA
A
B
27 W ±1%
DE
A
B
VB
D
Input
VOC(PP)
VOC
DVOC(SS)
CL = 50 pF ±20%
27 W ±1%
VOC
CL Includes Fixture and
Instrumentation Capacitance
Copyright © 2016, Texas Instruments Incorporated
图7-2. Measurement of Driver Differential and Common-Mode Output With RS-485 Load
3 V
VCC
VI
50%
50%
DE
CL = 50 pF ±20%
A
B
D
tPLH
tPHL
VOD
CL Includes Fixture
» 2 V
and Instrumentation
Capacitance
Input
Generator
RL = 54 W
±1%
90%
90%
VI
VOD
50 W
0 V
10%
0 V
10%
» –2 V
tr
tf
Copyright © 2016, Texas Instruments Incorporated
图7-3. Measurement of Driver Differential Output Rise and Fall Times and Propagation Delays
3 V
A
S1
VO
D
VI
50%
50%
3 V
B
0 V
DE
0.5 V
RL = 110 W
± 1%
CL = 50 pF ±20%
tPZH
VOH
90%
Input
Generator
CL Includes Fixture
50 W
VI
and Instrumentation
Capacitance
VO
50%
» 0 V
tPHZ
Copyright © 2016, Texas Instruments Incorporated
D at 3 V to test non-inverting output, D at 0 V to test inverting output.
图7-4. Measurement of Driver Enable and Disable Times With Active High Output and Pulldown Load
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
3 V
RL = 110 W
±1%
» 3 V
A
VI
50%
50%
S1
D
VO
3 V
0 V
B
tPZL
tPLZ
DE
CL = 50 pF ±20%
» 3 V
Input
Generator
VI
50 W
CL Includes Fixture
VO
50%
and Instrumentation
Capacitance
10%
VOL
Copyright © 2016, Texas Instruments Incorporated
D at 0 V to test non-inverting output, D at 3 V to test inverting output.
图7-5. Measurement of Driver Enable and Disable Times With Active-Low Output and Pullup Load
A
VO
R
Input
Generator
50 W
VI
B
1.5 V
0 V
CL = 15 pF ±20%
RE
CL Includes Fixture
and Instrumentation
Capacitance
3 V
VI
50%
50%
0 V
tPLH
tPHL
VOH
90% 90%
VO
50%
10%
50%
10%
VOL
tr
tf
Copyright © 2016, Texas Instruments Incorporated
图7-6. Measurement of Receiver Output Rise and Fall Times and Propagation Delays
Copyright © 2022 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
3 V
DE
VCC
A
B
VO
1 kW ± 1%
R
D
0 V or 3 V
S1
CL = 15 pF ±20%
RE
CL Includes Fixture
and Instrumentation
Capacitance
Input
Generator
50 W
VI
3 V
VI
50%
50%
0 V
tPZH(1)
tPHZ
VOH
D at 3 V
S1 to GND
90%
VO
50%
» 0 V
tPZL(1)
tPLZ
VCC
D at 0 V
S1 to VCC
VO
50%
10%
VOL
Copyright © 2016, Texas Instruments Incorporated
图7-7. Measurement of Receiver Enable and Disable Times With Driver Enabled
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
VCC
A
VO
0 V or 1.5 V
1 kW ± 1%
CL = 15 pF ±20%
R
S1
B
1.5 V or 0 V
RE
CL Includes Fixture
and Instrumentation
Capacitance
Input
Generator
50 W
VI
3 V
VI
50%
0 V
tPZH(2)
VOH
A at 1.5 V
B at 0 V
S1 to GND
VO
50%
GND
VCC
tPZL(2)
A at 0 V
B at 1.5 V
S1 to VCC
VO
50%
VOL
Copyright © 2016, Texas Instruments Incorporated
图7-8. Measurement of Receiver Enable Times With Driver Disabled
Copyright © 2022 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
8 Detailed Description
8.1 Overview
The SN65HVD1781A-Q1 is a half-duplex RS-485 transceiver that operates at data rates up to 1 Mbps.
The device features a wide common-mode operating range and bus-pin fault protection up to ±70 V. The device
has an active-high driver enable and active-low receiver enable. A standby current of less than 1 µA can be
achieved by disabling both driver and receiver.
8.2 Functional Block Diagram
VCC
R
RE
A
B
DE
D
GND
Copyright © 2016, Texas Instruments Incorporated
8.3 Feature Description
Internal ESD protection circuits protect the transceiver bus terminals against ±16-kV Human Body Model (HBM)
electrostatic discharges.
Device operation is specified over a wide temperature range from –40°C to 125°C.
8.3.1 Receiver Failsafe
The SN65HVD1781A-Q1 half-duplex transceiver provides internal biasing of the receiver input thresholds in
combination with large input-threshold hysteresis. At a positive input threshold of VIT+ = –35 mV and an input
hysteresis of VHYS = 30 mV, the receiver output remains logic high under bus-idle, bus-short, or open bus
conditions in the presence of up to 130-mVPP differential noise without the need for external failsafe biasing
resistors.
8.3.2 Hot-Plugging
The SN65HVD1781A-Q1 is designed to operate in hot swap or hot-pluggable applications. Key features for hot-
pluggable applications are power-up and power-down glitch free operation, default disabled input and output
pins, and receiver failsafe.
As shown in the 节8.2, an internal power-on reset circuit keeps the driver outputs in a high impedance state until
the supply voltage has reached a level at which the device will reliably operate. This circuit ensures that no
problems occur on the bus pin outputs as the power supply turns on or off.
As shown in 节 8.4, the driver and receiver enable inputs (DE and RE) are disabled by default. This default
ensures that the device neither drives the bus nor reports data on the R pin until the associated controller
actively drivers the enable pins.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
8.4 Device Functional Modes
When the driver enable pin, DE, is logic high, the differential outputs A and B follow the logic states at data input
D. A logic high at D causes A to turn high and B to turn low. In this case the differential output voltage defined as
VOD = VA – VB is positive. When D is low, the output states reverse, B turns high, A becomes low, and VOD is
negative.
When DE is low, both outputs turn high-impedance. In this condition the logic state at D is irrelevant. The DE pin
has an internal pull-down resistor to ground, thus when left open the driver is disabled (high-impedance) by
default. The D pin has an internal pull-up resistor to VCC, thus, when left open while the driver is enabled, output
A turns high and B turns low.
表8-1. Driver Function Table
INPUT
ENABLE
OUTPUTS
DRIVER STATE
D
DE
A
B
L
H
H
H
L
Actively drive bus High
L
X
H
L
H
Z
Z
L
Actively drive bus Low
Driver disabled
Z
Z
H
X
OPEN
H
Driver disabled by default
Actively drive bus High by default
OPEN
When the receiver enable pin, RE, is logic low, the receiver is enabled. When the differential input voltage
defined as VID = VA – VB is positive and higher than the positive input threshold, VIT+, the receiver output, R,
turns high. When VID is negative and lower than the negative input threshold, VIT–, the receiver output, R, turns
low. If VID is between VIT+ and VIT– the output is indeterminate.
When RE is logic high or left open, the receiver output is high-impedance and the magnitude and polarity of VID
are irrelevant. Internal biasing of the receiver inputs causes the output to go failsafe-high when the transceiver is
disconnected from the bus (open-circuit), the bus lines are shorted (short-circuit), or the bus is not actively driven
(idle bus).
表8-2. Receiver Function Table
DIFFERENTIAL INPUT
VID = VA –VB
VID > VIT+
ENABLE OUTPUT
RECEIVER STATE
RE
R
H
?
L
Receive valid bus High
VIT– < VID < VIT+
VID < VIT–
L
Indeterminate bus state
Receive valid bus Low
Receiver disabled
L
L
X
H
Z
Z
H
H
H
X
OPEN
Receiver disabled by default
Fail-safe high output
Fail-safe high output
Fail-safe high output
Open-circuit bus
Short-circuit bus
Idle (terminated) bus
L
L
L
Copyright © 2022 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
9 Application and Implementation
备注
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
9.1 Application Information
The SN65HVD1781A-Q1 is a half-duplex RS-485 transceiver commonly used for asynchronous data
transmissions. The driver and receiver enable pins allow for the configuration of different operating modes.
R
R
R
R
R
R
RE
A
B
RE
A
B
RE
A
B
DE
D
DE
D
DE
D
D
D
D
Copyright © 2016, Texas Instruments Incorporated
图9-1. Half-Duplex Transceiver Configurations
Using independent enable lines provides the most flexible control as it allows for the driver and the receiver to be
turned on and off individually. While this configuration requires two control lines, it allows for selective listening
into the bus traffic, whether the driver is transmitting data or not.
Combining the enable signals simplifies the interface to the controller by forming a single direction-control signal.
In this configuration, the transceiver operates as a driver when the direction-control line is high, and as a receiver
when the direction-control line is low.
Additionally, only one line is required when connecting the receiver-enable input to ground and controlling only
the driver-enable input. In this configuration, a node not only receives the data from the bus, but also the data it
sends and can verify that the correct data have been transmitted.
9.2 Typical Application
An RS-485 bus consists of multiple transceivers connecting in parallel to a bus cable. To eliminate line
reflections, each cable end is terminated with a termination resistor, RT, whose value matches the characteristic
impedance, Z0, of the cable. This method, known as parallel termination, allows for higher data rates over longer
cable length.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
R
R
R
R
A
B
A
B
RE
RE
RT
RT
DE
D
DE
D
D
D
A
B
A
B
R
R
R
R
D
D
D
D
RE DE
RE DE
Copyright © 2016, Texas Instruments Incorporated
图9-2. Typical RS-485 Network With Half-Duplex Transceivers
9.2.1 Design Requirements
RS-485 is a robust electrical standard suitable for long-distance networking that may be used in a wide range of
applications with varying requirements, such as distance, data rate, and number of nodes.
9.2.1.1 Data Rate and Bus Length
There is an inverse relationship between data rate and bus length, meaning the higher the data rate, the shorter
the cable length; and conversely, the lower the data rate, the longer the cable may be without introducing data
errors. While most RS-485 systems use data rates between 10 kbps and 100 kbps, some applications require
data rates up to 250 kbps at distances of 4000 feet and longer. Longer distances are possible by allowing for
small signal jitter of up to 5 or 10%.
10000
5%, 10%, and 20% Jitter
1000
Conservative
Characteristics
100
10
100
1k
10k
100 k
1M
10M
100 M
Data Rate (bps)
图9-3. Cable Length vs Data Rate Characteristic
9.2.1.2 Bus Loading
The RS-485 standard specifies that a compliant driver must be able to driver 32 unit loads (UL), where 1 unit
load represents a load impedance of approximately 12 kΩ. Because the SN65HVD1781A-Q1 consists of 1/10
UL transceivers, it is possible to connect up to 320 receivers to the bus.
9.2.2 Detailed Design Procedure
Although the SN65HVD1781A-Q1 is internally protected against human-body-model ESD strikes up to ±16 kV,
additional protection against higher-energy transients can be provided at the application level by implementing
external protection devices.
图 9-4 shows a protection circuit intended to withstand ±8-kV IEC ESD (per IEC 61000-4-2) as well as ±4-kV
EFT (per IEC 61000-4-4).
Copyright © 2022 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
3.3 V
100 nF
100 nF
VCC
10 kꢀ
R1
R
RxD
TVS
RE
DE
D
A
B
MCU/
UART
DIR
TxD
R2
GND
10 kꢀ
Copyright © 2016, Texas Instruments Incorporated
图9-4. RS-485 Transceiver with External Transient Protection
表9-1. Bill of Materials
DEVICE
FUNCTION
ORDER NUMBER
MANUFACTURER
XCVR
RS-485 Transceiver
SN65HVD1781A-Q1
TI
10-Ω, Pulse-Proof Thick-Film
R1, R2
TVS
CRCW0603010RJNEAHP
SMBJ43CA
Vishay
Resistor
Bidirectional 600-W Transient
Suppressor
Littelfuse
9.2.2.1 Stub Length
When connecting a node to the bus, the distance between the transceiver inputs and the cable trunk, known as
the stub, should be as short as possible. Stubs present a non-terminated piece of bus line which can introduce
reflections as the length of the stub increases. As a general guideline, the electrical length, or round-trip delay, of
a stub should be less than one-tenth of the rise time of the driver, thus giving a maximum physical stub length as
shown in 方程式1.
Lstub ≤0.1 × tr × v × c
(1)
where
• tr is the 10/90 rise time of the driver
• c is the speed of light (3 × 108 m/s)
• v is the signal velocity of the cable or trace as a factor of c
9.2.2.2 Receiver Failsafe
The differential receivers of the SN65HVD1781A-Q1 has receiver input thresholds that are offset so that receiver
output state is known for the following three fault conditions:
• Open bus conditions, such as a disconnected connector
• Shorted bus conditions, such as cable damage shorting the twisted-pair together
• Idle bus conditions that occur when no driver on the bus is actively driving
In any of these cases, the differential receiver will output a failsafe logic High state so that the output of the
receiver is not indeterminate.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
Receiver failsafe is accomplished by offsetting the receiver thresholds such that the input indeterminate range
does not include zero volts differential. In order to comply with the RS-422 and RS-485 standards, the receiver
output must output a High when the differential input VID is more positive than 200 mV, and must output a Low
when VID is more negative than –200 mV. The receiver parameters which determine the failsafe performance
are VIT(+), VIT(–), and VHYS (the separation between VIT(+) and VIT(–)). As shown in the 节 6.6 table, differential
signals more negative than –200mV will always cause a Low receiver output, and differential signals more
positive than 200 mV will always cause a High receiver output.
When the differential input signal is close to zero, it is still above the maximum VIT(+) threshold of –35 mV, and
the receiver output will be High. Only when the differential input is more than VHYS below VIT(+) will the receiver
output transition to a Low state. Therefore, the noise immunity of the receiver inputs during a bus fault condition
includes the receiver hysteresis value, VHYS, as well as the value of VIT(+)
.
R
Vhys (min)
30 mV
VID (mV)
-65
-35
0
+65
Vn max = 130 mVpp
图9-5. Noise Immunity Under Bus Fault Conditions
9.2.3 Application Curve
SN65HVD1781-Q1 D Input
Differential Output
R Output
1-Mbps Operation
图9-6. SN65HVD1781A-Q1 PRBS Data Pattern
Copyright © 2022 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
10 Power Supply Recommendations
To ensure reliable operation at all data rates and supply voltages, each supply should be buffered with a 100-nF
ceramic capacitor located as close to the supply pins as possible. The TPS7A6150-Q1 is a linear voltage
regulator suitable for the 5-V supply.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
11 Layout
11.1 Layout Guidelines
On-chip IEC-ESD protection is good for laboratory and portable equipment but often insufficient for EFT and
surge transients occurring in industrial environments. Therefore robust and reliable bus node design requires the
use of external transient protection devices.
Because ESD and EFT transients have a wide frequency bandwidth from approximately 3 MHz to 3 GHz, high-
frequency layout techniques must be applied during PCB design.
1. Place the protection circuitry close to the bus connector to prevent noise transients from entering the board.
2. Use VCC and ground planes to provide low-inductance. High-frequency currents follow the path of least
inductance and not the path of least impedance.
3. Design the protection components into the direction of the signal path. Do not force the transient currents to
divert from the signal path to reach the protection device.
4. Apply 100-nF to 220-nF bypass capacitors as close as possible to the VCC pins of the transceiver, UART, or
controller ICs on the board.
5. Use at least two vias for VCC and ground connections of bypass capacitors and protection devices to
minimize effective via inductance.
6. Use 1-kΩto 10-kΩpullup and pulldown resistors for enable lines to limit noise currents in these lines during
transient events.
7. While pure TVS protection is sufficient for surge transients up to 1 kV, higher transients require metal-oxide
varistors (MOVs) which reduce the transients to a few hundred volts of clamping voltage, and transient
blocking units (TBUs) that limit transient current to less than 1 mA.
11.2 Layout Example
5
Via to ground
Via to VCC
4
C
R
6
R
R
1
R
MCU
5
TVS
6
SN65HVD1781
5
图11-1. Half-Duplex Layout Example
Copyright © 2022 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: SN65HVD1781A-Q1
SN65HVD1781A-Q1
ZHCSG90A –MAY 2017 –REVISED FEBRUARY 2022
www.ti.com.cn
12 Device and Documentation Support
12.1 Device Support
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation see the following:
• RS-485 Half-Duplex Evaluation Module
• SN65HVD17xx Fault-Protected RS-485 Transceivers With Extended Common-Mode Range
• TPS7A6xxx-Q1 300-mA 40-V Low-Dropout Regulator With 25-µA Quiescent Current
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.4 Community Resources
12.5 Trademarks
所有商标均为其各自所有者的财产。
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: SN65HVD1781A-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jan-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
SN65HVD1781AQDRQ1
ACTIVE
SOIC
D
8
2500 RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
1781AQ
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明