SN65HVD235QDRQ1 [TI]
3.3V 汽车类 CAN 总线收发器 | D | 8 | -40 to 125;型号: | SN65HVD235QDRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 3.3V 汽车类 CAN 总线收发器 | D | 8 | -40 to 125 总线收发器 |
文件: | 总36页 (文件大小:1615K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
SN65HVD23x-Q1 3.3V 汽车类 CAN 总线收发器
1 特性
3 说明
1
•
符合 ISO 11898-2 标准
适用于汽车电子 应用
具有符合 AEC-Q100 标准的下列结果:
SN65HVD233-Q1、SN65HVD234-Q1 和
SN65HVD235-Q1 器件是适用于汽车类应用的 3.3V 故
障保护 CAN 收发器。这些收发器由 3.3V 单电源供电
运行,非常适合同样采用 3.3V 微控制器的系统,因为
不再需要通过附加组件或独立电源分别为控制器和
CAN 收发器供电。SN65HVD23x-Q1 收发器符合
ISO 11898-2 标准,因此可在使用 5V CAN 和/或 3.3V
CAN 收发器的混合网络中进行互操作。
•
•
–
器件温度 1 级:-40°C 至 125°C 的环境运行温
度范围
–
器件人体模型 (HBM) 静电放电 (ESD) 分类等
级:
–
–
总线引脚:±12 000V
其他引脚:±3 000V
这些器件尤其适合工作在恶劣环境下,其具有串线保
护、过压保护(CANH 和 CANL 引脚上,最高达 ±
36V)、接地损耗保护、过热(热关断)保护以及
±100V 共模瞬态保护。这些器件工作在 –7V 至 12V 的
宽共模电压范围内。这些收发器可用作微处理器上的主
机 CAN 控制器与运输及汽车应用中的差分 CAN 总线
之间的 接口。
–
器件带电器件模型 (CDM) ESD 分类等级:±1
000V
•
•
•
•
•
•
3.3V 单电源电压
比特率:最高达 1Mbps
总线引脚故障保护:最高达 ±36V
–7V 至 12V 共模电压范围
高输入阻抗,允许连接 120 个节点
器件信息(1)
低电压晶体管-晶体管逻辑电路 (LVTTL) I/O 可耐受
5V 电压
器件型号
封装
封装尺寸(标称值)
•
•
•
•
•
•
•
符合 GIFT/ICT 标准
SN65HVD233-Q1
SN65HVD234-Q1
SN65HVD235-Q1
可调节的驱动器转换率,能够改善辐射性能
未供电节点不会干扰总线
SOIC (8)
4.90mm x 3.91mm
低电流待机模式(典型值为 200μA)
平均功耗:36.4mW
(1) 要了解所有可用封装,请见数据表末尾的可订购产品附录。
框图
SN65HVD233-Q1:环回模式
SN65HVD234-Q1:超低电流休眠模式
VCC
VCC
–
50nA 流耗典型值
•
•
•
SN65HVD235-Q1:自动波特环回模式
热关断保护
VCC
TXD
上电和掉电时总线输入和输出上无毛刺脉冲
–
–
高输入阻抗,低 VCC
VCC
掉电再上电期间的输出呈单调性
RS
Slope Control
and
Mode Logic
2 应用
AB, EN,
or LBK
•
•
•
•
•
•
车内网络
RXD
先进的驾驶员辅助系统 (ADAS)
车身电子装置和照明
GND
信息娱乐和仪表板
混合、电动和动力传动系统
符合 CAN 总线标准(例如,NMEA 2000 和 SAE
J1939)的应用
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SLLSES4
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
目录
10.1 Overview ............................................................... 18
10.2 Functional Block Diagrams ................................... 18
10.3 Feature Description............................................... 18
10.4 Device Functional Modes...................................... 20
11 Application and Implementation........................ 22
11.1 Application Information.......................................... 22
11.2 Typical Application ................................................ 23
11.3 System Example ................................................... 25
12 Power Supply Recommendations ..................... 26
13 Layout................................................................... 26
13.1 Layout Guidelines ................................................. 26
13.2 Layout Example .................................................... 27
14 器件和文档支持 ..................................................... 28
14.1 相关链接................................................................ 28
14.2 接收文档更新通知 ................................................. 28
14.3 社区资源................................................................ 28
14.4 商标....................................................................... 28
14.5 静电放电警告......................................................... 28
14.6 Glossary................................................................ 28
15 机械、封装和可订购信息....................................... 28
1
2
3
4
5
6
7
8
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
说明 (续).............................................................. 3
Device Comparison Table..................................... 3
Pin Configuration and Functions......................... 4
Specifications......................................................... 5
8.1 Absolute Maximum Ratings ..................................... 5
8.2 ESD Ratings.............................................................. 5
8.3 Recommended Operating Conditions....................... 5
8.4 Thermal Information.................................................. 6
8.5 Electrical Characteristics: Driver ............................... 6
8.6 Electrical Characteristics: Receiver .......................... 7
8.7 Switching Characteristics: Driver .............................. 7
8.8 Switching Characteristics: Receiver.......................... 8
8.9 Switching Characteristics: Device............................. 8
8.10 Typical Characteristics............................................ 9
Parameter Measurement Information ................ 11
9
10 Detailed Description ........................................... 18
4 修订历史记录
注:之前版本的页码可能与当前版本有所不同。
Changes from Original (September 2016) to Revision A
Page
•
•
Deleted extra words "all pins except" in the test condition for CANH, CANL pins to GND ................................................... 5
Added ESD performance information between CANH and CANL pins ................................................................................ 5
2
版权 © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
5 说明 (续)
模式:SN65HVD233-Q1、SN65HVD234-Q1 和 SN65HVD235-Q1 器件的 RS 引脚(引脚 8)提供三种工作模
式:高速、斜率控制和低功耗待机模式。将引脚 8 直接接地可选择高速工作模式,该工作模式允许驱动器输出晶体
管以尽可能快的速度导通和关断,而且对上升和下降斜率没有限制。通过在 RS 引脚与地之间串联一个电阻可以调
节上升和下降斜率。斜率与引脚的输出电流成比例。当电阻值为 10kΩ 时,器件的转换率约为 15V/μs;当电阻值为
100kΩ 时,器件的转换率约为 2V/μs。有关斜率控制的更多信息,请参见Feature Description。
如果对 RS 引脚施加逻辑高电平,SN65HVD233-Q1、SN65HVD234-Q1 和 SN65HVD235-Q1 器件将进入低电流
待机(仅监听)模式。在此模式下,驱动器将关断、接收器保持工作状态。如果本地协议控制器必须向总线发送消
息,则它必须同时通过 RS 引脚使器件返回高速模式或斜率控制模式。
环回 (SN65HVD233-Q1):当 SN65HVD233-Q1 器件的环回 (LBK) 引脚(引脚 5)为逻辑高电平时,会将总线输
出和总线输入置于高阻抗状态。器件内部的 TXD 至 RS 路径保持有效状态,可用于驱动器至接收器环回,从而实
现在不干扰总线的情况下执行自诊断节点功能。关于环回模式的更多信息,请参见Feature Description。
超低电流休眠 (SN65HVD234-Q1):如果向 EN 引脚(引脚 5)施加逻辑低电平,则 SN65HVD234-Q1 器件将进入
超低电流休眠模式,继而将禁止驱动器和接收器电路。在通过向引脚 5 施加逻辑高电平来激活电路之前,该器件将
保持在该休眠模式下。
自动波特环回 (SN65HVD235-Q1):SN65HVD235-Q1 器件的 AB 引脚(引脚 5)实现了总线仅监听环回功能,允
许本地节点控制器将其波特率与 CAN 总线的波特率同步。在自动波特模式下,驱动器的总线输出处于高阻抗状
态,而接收器的总线输入保持有效状态。器件内部有一条 TXD 引脚到 RS 引脚的环回路径,方便控制器执行波特
率检测或自动波特功能。关于自动波特模式的更多信息,请参见Feature Description。
6 Device Comparison Table
SLOPE
CONTROL
DIAGNOSTIC
LOOPBACK
AUTOBAUD
LOOPBACK
PART NUMBER(1)
LOW-POWER MODE
SN65HVD233-Q1
SN65HVD234-Q1
SN65HVD235-Q1
200-μA standby mode
200-μA standby mode or 50-nA sleep mode
200-μA standby mode
Adjustable
Adjustable
Adjustable
Yes
No
No
No
No
Yes
(1) For the most-current package and ordering information, see the orderable addendum at the end of the data sheet, or see the TI Web
site at www.ti.com.
Copyright © 2016, Texas Instruments Incorporated
3
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
7 Pin Configuration and Functions
D Package
8-Pin SOIC
D Package
8-Pin SOIC
SN65HVD233-Q1 Top View
SN65HVD234-Q1 Top View
TXD
GND
VCC
RXD
1
2
3
4
8
7
6
5
RS
TXD
GND
VCC
RXD
1
2
3
4
8
7
6
5
RS
CANH
CANL
LBK
CANH
CANL
EN
Not to scale
Not to scale
D Package
8-Pin SOIC
SN65HVD235-Q1 Top View
TXD
1
2
3
4
8
7
6
5
RS
GND
VCC
RXD
CANH
CANL
AB
Not to scale
Pin Functions
PIN
NO.
I/O
DESCRIPTION
NAME
'233-Q1
'234-Q1
'235-Q1
SN65HVD235-Q1 device: Autobaud loopback mode-input pin (AB). Can be tied to
ground if not used. Can also be left open if unused because the internal pulldown
biases this toward ground.
AB
—
—
5
I
CANH
CANL
7
6
7
6
7
6
I/O High-level CAN bus line
I/O Low-level CAN bus line
SN65HVD234-Q1 device: Enable input pin. Logic high for enabling a normal mode
(high-speed or slope-control mode). Logic low for sleep mode. (EN)
EN
—
2
5
2
—
2
I
GND
—
I
Ground connection
SN65HVD233-Q1 device: Loopback-mode input pin (LBK). Can be tied to ground if
not used. Can also be left open if unused because the internal pulldown biases this
toward ground.
LBK
5
—
—
Mode-select pin: strong pulldown to GND = high-speed mode, strong pullup to VCC
= low-power mode, 10-kΩ to 100-kΩ pulldown to GND = slope-control mode
RS
8
8
8
I
RXD
TXD
VCC
4
1
3
4
1
3
4
1
3
O
I
CAN receive data output (LOW for dominant and HIGH for recessive bus states)
CAN transmit data input (LOW for dominant and HIGH for recessive bus states)
Transceiver 3.3-V supply voltage
I
4
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
8 Specifications
8.1 Absolute Maximum Ratings
over operating ambient temperature range unless otherwise noted(1)(2)
MIN
–0.3
–36
MAX
7
UNIT
V
VCC Supply voltage
Voltage at any bus terminal (CANH or CANL)
36
V
Voltage input, transient pulse, CANH and CANL, through 100 Ω (see
Figure 18)
–100
100
V
VI
Input voltage, (AB, EN, LBK, RS, TXD)
Output voltage (RXD)
–0.5
–0.5
–10
–40
7
V
V
VO
IO
7
Receiver output current
10
150
125
mA
°C
°C
TJ
Operating junction temperature
Storage temperature
Tstg
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential I/O bus voltages, are with respect to the network ground pin.
8.2 ESD Ratings
VALUE
UNIT
CANH, CANL to GND
±12 000
Human-body model (HBM), per AEC
Q100-002(1)
Between CANH and
CANL
±16 000
V(ESD)
Electrostatic discharge
V
All pins
±3 000
±1 000
Charged-device model (CDM), per AEC Q100-011
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
8.3 Recommended Operating Conditions
MIN
MAX UNIT
VCC
Supply voltage
3
3.6
12
V
V
Voltage at any bus terminal (separately or common mode)
–7
VIH
VIL
VID
High-level input voltage
Low-level input voltage
EN, AB, LBK, TXD
EN, AB, LBK, TXD
2
5.5
0.8
6
V
0
–6
V
Differential input voltage between CANH and CANL
Resistance from RS to ground
V
0
100
5.5
kΩ
V
VI(Rs) Input voltage at RS for standby
0.75 VCC
–50
Driver
IOH
High-level output current
mA
Receiver
Driver
–10
50
10
IOL
TA
Low-level output current
mA
°C
Receiver
Operating ambient temperature(1)
–40
125
(1) Maximum ambient temperature operation is allowed as long as the device maximum junction temperature is not exceeded.
Copyright © 2016, Texas Instruments Incorporated
5
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
8.4 Thermal Information
SN65HVD23x-Q1
D (SOIC)
8 PINS
102.8
THERMAL METRIC(1)
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
45.1
43.8
Junction-to-top characterization parameter
Junction-to-board characterization parameter
7.3
ψJB
43.2
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
8.5 Electrical Characteristics: Driver
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP(1)
MAX UNIT
CANH
CANL
CANH
CANL
2.45
0.5
VCC
Bus output voltage
(dominant)
TXD at 0 V, RS at 0 V, see Figure 12 and
Figure 13
VO(D)
V
1.25
2.3
Bus output voltage
(recessive)
TXD at 3 V, RS at 0 V, see Figure 12 and
Figure 13
VO
V
2.3
TXD at 0 V, RS at 0 V, see Figure 12 and
Figure 13
1.5
1.2
2
2
3
V
3
VOD(D)
Differential output voltage (dominant)
Differential output voltage (recessive)
TXD at 0 V, RS at 0 V, see Figure 13 and
Figure 14
TXD at 3 V, RS at 0 V, see Figure 12 and
Figure 13
–120
–0.5
12
mV
VOD
TXD at 3 V, RS at 0 V, no load
See Figure 21
0.05
V
V
VOC(pp) Peak-to-peak common-mode output voltage
1
AB, EN, LBK, TXD = 2 V or EN = 2 V or LBK = 2 V or AB =
TXD 2 V
IIH
IIL
High-level input current
Low-level input current
–30
30
30
μA
μA
AB, EN, LBK, TXD = 0.8 V or EN = 0.8 V or LBK = 0.8 V or
–30
TXD
AB = 0.8 V
VCANH = –7 V, CANL open, see Figure 26
VCANH = 12 V, CANL open, see Figure 26
VCANL = –7 V, CANH open, see Figure 26
VCANL = 12 V, CANH open, see Figure 26
–250
1
IOS
Short-circuit output current
Output capacitance
mA
–1
250
See CI, Input capacitance in Electrical
Characteristics: Receiver
CO
IIRs(s)
RS input current for standby
Sleep
RS at 0.75 VCC
–10
μA
μA
EN at 0 V, TXD at VCC, RS at 0 V or VCC
0.05
200
2
RS at VCC, TXD at VCC, AB at 0 V, LBK at 0 V,
EN at VCC
Standby
600
ICC
Supply current
Dominant
TXD at 0 V, no load, AB at 0 V, LBK at 0 V,
RS at 0 V, EN at VCC
6
6
mA
TXD at VCC, no load, AB at 0 V, LBK at 0 V,
RS at 0 V, EN at VCC
Recessive
RL = 60 Ω, RS at 0 V, input to D a 1-MHz 50%
duty
P(AVG)
Average power dissipation
36.4
mW
cycle square wave VCC at 3.3 V, TA = 25°C
(1) All typical values are at 25°C and with a 3.3-V supply.
6
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
8.6 Electrical Characteristics: Receiver
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP(1)
MAX UNIT
VIT+
VIT–
Vhys
Positive-going input threshold voltage
750
900
mV
mV
mV
Negative-going input threshold voltage AB at 0 V, LBK at 0 V, EN at VCC, see Table 1
500
650
100
Hysteresis voltage (VIT+ – VIT–
High-level output voltage
Low-level output voltage
)
0.8 ×
VCC
VOH
VOL
IO = –4 mA, See Figure 17
V
V
IO = 4 mA, See Figure 17
CANH or CANL at 12 V
0.4
150
200
500
CANH or CANL at 12 V,
VCC at 0 V
Other bus pin at 0 V,
TXD at 3 V, AB at 0 V,
LBK at 0 V, RS at 0 V,
EN at VCC
600
–150
–130
II
Bus input current
μA
CANH or CANL at –7 V
–610
–450
CANH or CANL at –7 V,
VCC at 0 V
Pin-to-ground, VI = 0.4 sin (4E6πt) + 0.5 V, TXD at 3 V,
AB at 0 V, LBK at 0 V, EN at VCC
CI
Input capacitance (CANH or CANL)
40
20
pF
Pin-to-pin, VI = 0.4 sin (4E6πt) + 0.5 V, TXD at 3 V,
AB at 0 V, LBK at 0 V, EN at VCC
CID
RID
RIN
Differential input capacitance
Differential input resistance
pF
kΩ
kΩ
40
20
100
50
TXD at 3 V, AB at 0 V, LBK at 0 V, EN at VCC
Input resistance (CANH or CANL) to
ground
Sleep
EN at 0 V, TXD at VCC, RS at 0 V or VCC
0.05
200
2
μA
RS at VCC, TXD at VCC, AB at 0 V, LBK at 0 V, EN at
VCC
Standby
600
ICC
Supply current
Dominant
TXD at 0 V, no load, RS at 0 V, LBK at 0 V, AB at 0 V,
EN at VCC
6
6
mA
TXD at VCC, no load, RS at 0 V, LBK at 0 V, AB at 0 V,
EN at VCC
Recessive
(1) All typical values are at 25°C and with a 3.3-V supply.
8.7 Switching Characteristics: Driver
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP(1)
MAX UNIT
RS at 0 V, see Figure 15
35
85
Propagation delay time,
low-to-high-level output
tPLH
RS with 10 kΩ to ground, see Figure 15
RS with 100 kΩ to ground, see Figure 15
RS at 0 V, see Figure 15
70
125
870
ns
ns
ns
ns
ns
500
70
120
Propagation delay time,
high-to-low-level output
tPHL
RS with 10 kΩ to ground, see Figure 15
RS with 100 kΩ to ground, see Figure 15
RS at 0 V, see Figure 15
130
180
870
1200
35
tsk(p) Pulse skew (|tPHL – tPLH|)
RS with 10 kΩ to ground, see Figure 15
RS with 100 kΩ to ground, see Figure 15
RS at 0 V, see Figure 15
60
370
20
30
70
135
1400
70
tr
Differential output signal rise time
Differential output signal fall time
RS with 10 kΩ to ground, see Figure 15
RS with 100 kΩ to ground, see Figure 15
RS at 0 V, see Figure 15
350
20
tf
RS with 10 kΩ to ground, see Figure 15
RS with 100 kΩ to ground, see Figure 15
30
135
1400
1.5
350
0.6
1
ten(s) Enable time from standby to dominant
ten(z) Enable time from sleep to dominant
μs
μs
See Figure 19 and Figure 20
5
(1) All typical values are at 25°C and with a 3.3-V supply.
Copyright © 2016, Texas Instruments Incorporated
7
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
8.8 Switching Characteristics: Receiver
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP(1) MAX UNIT
tPLH Propagation delay time, CANH input low to RXD output high
tPHL Propagation delay time, CANH input high to RXD output low
tsk(p) Pulse skew (|tPHL – tPLH|)
35
35
7
60
60
ns
ns
ns
ns
ns
See Figure 17
tr
tf
Output signal rise time
Output signal fall time
2
5
5
2
(1) All typical values are at 25°C and with a 3.3-V supply.
8.9 Switching Characteristics: Device
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP(1)
MAX UNIT
Loopback delay, driver input to
receiver output
t(LBK)
t(AB1)
t(AB2)
'HVD233-Q1
'HVD235-Q1
See Figure 23
7.5
10
35
12
20
60
ns
ns
ns
Loopback delay, driver input to
receiver output
See Figure 24
See Figure 25
Loopback delay, bus input to
receiver output
RS at 0 V, see Figure 22
70
105
535
70
135
190
Total loop delay, driver input to receiver output,
recessive to dominant
t(loop1)
RS with 10 kΩ to ground, see Figure 22
RS with 100 kΩ to ground, see Figure 22
RS at 0 V, see Figure 22
ns
ns
1000
135
Total loop delay, driver input to receiver output,
dominant to recessive
t(loop2)
RS with 10 kΩ to ground, see Figure 22
RS with 100 kΩ to ground, see Figure 22
105
535
190
1000
(1) All typical values are at 25°C and with a 3.3-V supply.
8
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
8.10 Typical Characteristics
RS = LBK = AB = 0 V; EN = VCC
90
95
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
VCC = 3.6 V
VCC = 3.3 V
VCC = 3 V
85
90
80
75
70
65
60
85
80
75
70
65
-40
0
40
80
120
-40
0
40
80
120
Ambient Temperature (èC)
Ambient Temperature (èC)
D001
D002
Figure 1. Recessive-to-Dominant Loop Time vs Ambient
Temperature
Figure 2. Dominant-to-Recessive Loop Time vs Ambient
Temperature
160
20
19
18
17
16
15
140
120
100
80
60
40
20
0
200
300
400
500
600
700
800
900 1000
0
1
2
3
4
Frequency (kbps)
Low-Level Output Voltage (V)
D003
D004
VCC = 3.3 V
TA = 25°C
RL = 60-Ω Load
VCC = 3.3 V
TA = 25°C
Figure 3. Supply Current vs Frequency
Figure 4. Driver Low-Level Output Current vs Low-Level
Output Voltage
0.12
0.1
2.2
2
1.8
1.6
1.4
1.2
1
0.08
0.06
0.04
0.02
0
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
0
0.5
1
1.5
2
2.5
3
3.5
-40
0
40
80
120
High Level Output Voltage (V)
Ambient Temperature (èC)
D005
D006
VCC = 3.3 V
TA = 25°C
RL = 60 Ω
Figure 5. Driver High-Level Output Current vs High-Level
Output Voltage
Figure 6. Differential Output Voltage vs Ambient
Temperature
Copyright © 2016, Texas Instruments Incorporated
9
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
Typical Characteristics (continued)
RS = LBK = AB = 0 V; EN = VCC
45
38
37
36
35
34
33
32
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
44
43
42
41
40
39
38
37
36
35
-40
0
40
80
120
-40
0
40
80
120
Ambient Temperature (èC)
Ambient Temperature (èC)
D007
D008
See Figure 3
See Figure 3
Figure 7. Receiver Low-to-High Propagation Delay vs
Ambient Temperature
Figure 8. Receiver High-to-Low Propagation Delay vs
Ambient Temperature
55
65
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
60
55
50
45
40
35
30
50
45
40
35
30
25
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
-40
0
40
80
120
-40
0
40
80
120
Ambient Temperatrue (èC)
Ambient Temperatrue (èC)
D009
D00110
See Figure 1
See Figure 1
Figure 9. Driver Low-to-High Propagation Delay vs Ambient
Temperature
Figure 10. Driver High-to-Low Propagation Delay vs
Ambient Temperature
35
30
25
20
15
10
5
0
-5
0
0.6
1.2
1.8
2.4
3
3.6
Supply Voltage (V)
D011
TA = 25°C
RL = 60 Ω
Figure 11. Driver Output Current vs Supply Voltage
10
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
9 Parameter Measurement Information
I
O(CANH)
TXD
I
I
60 W 1%
V
OD
V
O(CANH)
V
+ V
2
O(CANH)
O(CANL)
II(RS)
RS
V
V
I
V
OC
I
O(CANL)
+
V
I(RS)
–
O(CANL)
Figure 12. Driver Voltage, Current, and Test Definition
Dominant
≈ 3 V
V
O(CANH)
Recessive
≈ 2.3 V
≈ 1 V
V
O(CANL)
Figure 13. Bus Logic State Voltage Definitions
330 W 1%
CANH
TXD
I
V
OD
V
60 W 1%
+
_
–7 V ≤ VTEST ≤ 12 V
RS
CANL
330 W 1%
Figure 14. Driver VOD
CANH
V
CC
VCC / 2
VCC / 2
CL = 50 pF 20%
(see Note B)
V
I
0 V
TXD
V
O
t
t
PHL
PLH
RL = 60 W 1%
V
I
RS
V
V
O(D)
+
90%
10%
0.9 V
V
O
V
0.5 V
I(RS)
(see Note A)
CANL
O(R)
–
t
r
t
f
A. The input pulse is supplied by a generator having the following characteristics: Pulse repetition rate (PRR) ≤ 125 kHz,
50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω.
B. CL includes fixture and instrumentation capacitance.
Figure 15. Driver Test Circuit and Voltage Waveforms
Copyright © 2016, Texas Instruments Incorporated
11
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
Parameter Measurement Information (continued)
CANH
RXD
I
O
VID
V
I(CANH)
VI(CANH)+ VI(CANL)
V
IC
=
2
VO
CANL
VI(CANL)
Figure 16. Receiver Voltage and Current Definitions
2.9 V
1.5 V
CANH
CANL
2.2 V
2.2 V
V
I
RXD
I
O
V
I
t
t
PHL
PLH
C
L
= 15 pF 20%
(see Note B)
1.5 V
V
V
OH
V
O
(see Note A)
90%
90%
50%
10%
50%
10%
V
O
OL
t
r
t
f
A. The input pulse is supplied by a generator having the following characteristics: Pulse repetition rate (PRR) ≤ 125 kHz,
50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω.
B. CL includes fixture and instrumentation capacitance.
Figure 17. Receiver Test Circuit and Voltage Waveforms
Table 1. Differential Input Voltage Threshold Test
INPUT
OUTPUT
RXD
MEASURED
|VID
VCANH
–6.1 V
12 V
VCANL
–7 V
|
L
L
900 mV
900 mV
6 V
11.1 V
–7 V
VOL
–1 V
L
12 V
6 V
L
6 V
–6.5 V
12 V
–7 V
H
H
H
H
H
500 mV
500 mV
6 V
11.5 V
–1 V
–7 V
VOH
6 V
12 V
6 V
Open
Open
X
CANH
CANL
RXD
100 W
Pulse Generator
15 µs Duration
1% Duty Cycle
TXD at 0 V or VCC
RS, AB, EN, LBK, at 0 V or V
CC
t , t ≤100 ns
r f
NOTE: This test is conducted to test survivability only. Data stability at the RXD output is not specified.
Figure 18. Test Circuit, Transient Overvoltage Test
12
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
’HVD234-Q1
’HVD233-Q1 or ’HVD235-Q1
RS
RS
CANH
CANH
60 W 1%
CANL
V
V
I
I
TXD
EN
TXD
60 W 1%
CANL
0 V
0 V
AB or LBK
V
CC
V
O
V
O
RXD
+
–
+
–
15 pF 20%
15 pF 20%
V
CC
50%
V
I
0 V
V
OH
OL
50%
V
O
V
t
en(s)
Copyright © 2016, Texas Instruments Incorporated
NOTE: All VI input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 6 ns, pulse repetition rate
(PRR) = 125 kHz, 50% duty cycle.
Figure 19. ten(s) Test Circuit and Voltage Waveforms
’HVD234-Q1
RS
V
CC
CANH
50%
V
I
TXD
EN
60 W 1%
CANL
0 V
0 V
V
I
V
OH
OL
50%
V
O
RXD
V
t
V
O
en(z)
+
–
15 pF 20%
:
NOTE All V input pulses are supplied by a generator having the following characteristics:
I
t or t ≤6 ns, pulse repetition rate (PRR) = 50 kHz, 50% duty cycle.
r f
Copyright © 2016, Texas Instruments Incorporated
Figure 20. ten(z) Test Circuit and Voltage Waveforms
27 W 1%
CANH
CANL
V
OC(PP)
TXD
V
OC
V
I
RS
V
OC
27 W 1%
50 pF 20%
:
NOTE All V input pulses are supplied by a generator having the following characteristics:
I
t or t ≤6 ns, pulse repetition rate (PRR) = 125 kHz, 50% duty cycle.
r f
Figure 21. VOC(pp) Test Circuit and Voltage Waveforms
Copyright © 2016, Texas Instruments Incorporated
13
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
0 W, 10 kW,
or 100 kW 5%
DUT
RS
CANH
V
CC
50%
50%
TXD
V
I
60 W 1%
V
I
0 V
LBK or AB
t
t
(loop1)
(loop2)
’HVD233-Q1, -235-Q1
EN
CANL
V
OH
OL
VCC
50%
50%
V
O
’HVD234-Q1
RXD
V
+
V
O
15 pF 20%
–
:
NOTE All V input pulses are supplied by a generator having the following characteristics:
I
t or t ≤6 ns, pulse repetition rate (PRR) = 125 kHz, 50% duty cycle.
r
f
Copyright © 2016, Texas Instruments Incorporated
Figure 22. t(loop) Test Circuit and Voltage Waveforms
’HVD233-Q1
V
RS
D
CC
CANH
50%
50%
V
I
+
0 V
V
I
V
OD
60 W 1%
–
t
t
(LBK2)
(LBK1)
V
LBK
R
OH
V
CC
CANL
50%
= t
50%
V
O
V
OL
t
= t
(LBK2)
(LBK)
(LBK1)
V
OD
≈2.3 V
+
V
O
15 pF 20%
–
:
NOTE All V input pulses are supplied by a generator having the following characteristics:
I
t or t ≤6 ns, pulse repetition rate (PRR) = 125 kHz, 50% duty cycle.
r f
Copyright © 2016, Texas Instruments Incorporated
Figure 23. t(LBK) Test Circuit and Voltage Waveforms
’HVD235-Q1
V
OD
≈2.3 V
RS
CANH
V
CC
+
TXD
50%
50%
60 W 1%
V
I
V
I
V
–
OD
0 V
CANL
t
t
(ABL)
(ABH)
AB
V
OH
OL
V
CC
50%
= t
50%
V
O
RXD
V
t
= t
(AB1)
(ABH)
(ABL)
+
–
V
O
15 pF 20%
:
NOTE All V input pulses are supplied by a generator having the following characteristics:
I
tr or tf ≤ 6 ns, pulse repetition rate (PRR) = 125 kHz, 50% duty cycle.
Copyright © 2016, Texas Instruments Incorporated
Figure 24. t(AB1) Test Circuit and Voltage Waveforms
14
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
’HVD235-Q1
RS
CANH
2.9 V
2.2 V
2.2 V
V
I
TXD
V
CC
60 W 1%
V
I
1.5 V
t
t
(ABL)
1.5 V
(ABH)
AB
CANL
V
OH
OL
V
CC
50%
= t
50%
V
O
RXD
V
t
= t
(AB2)
(ABH)
(ABL)
+
–
V
O
15 pF 20%
:
NOTE All V input pulses are supplied by a generator having the following characteristics:
I
t or t ≤6 ns, pulse repetition rate (PRR) = 125 kHz, 50% duty cycle.
r f
Copyright © 2016, Texas Instruments Incorporated
Figure 25. t(AB2) Test Circuit and Voltage Waveforms
| IOS
|
I
OS
15 s
CANH
TXD
0 V
0 V or V
CC
+
_
I
OS
V
I
12 V
CANL
V
I
0 V
0 V
and
10 µs
V
I
–7 V
Figure 26. IOS Test Circuit and Waveforms
Copyright © 2016, Texas Instruments Incorporated
15
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
3.3 V
TA = 25°C
= 3.3 V
V
CC
R2 1%
R1 1%
R1 1%
CANH
CANL
+
ID
–
RXD
V
V
ac
V
I
R2 1%
The RXD Output State Does Not Change During
Application of the Input Waveform.
V
ID
R1
R2
500 mV
900 mV
50 W
50 W
280 W
130 W
12 V
–7 V
V
I
NOTE: All input pulses are supplied by a generator with f ≤ 1.5 MHz.
Figure 27. Common-Mode Voltage Rejection
16
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
TXD INPUT
RS INPUT
CANH INPUT
V
CC
V
CC
V
CC
110 kW
45 kW
9 kW
100 kW
1 kW
INPUT
INPUT
9 V
9 kW
40 V
+
_
INPUT
CANL INPUT
CANH and CANL OUTPUTS
RXD OUTPUT
V
CC
V
CC
V
CC
110 kW
45 kW
9 kW
5 W
OUTPUT
9 V
INPUT
OUTPUT
40 V
9 kW
40 V
EN INPUT
LBK or AB INPUT
V
CC
V
CC
1 kW
1 kW
INPUT
INPUT
100 kW
100 kW
9 V
9 V
Figure 28. Equivalent Input and Output Schematic Diagrams
Copyright © 2016, Texas Instruments Incorporated
17
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
10 Detailed Description
10.1 Overview
This family of CAN transceivers is compatible with the ISO 11898-2 high-speed controller-area-network (CAN)
physical layer standard. These devices are designed to interface between the differential bus lines in CAN and
the CAN protocol controller at data rates up to 1 Mpbs.
10.2 Functional Block Diagrams
RS
CANH
TXD
CANL
LBK
RXD
LBK
Figure 29. SN65HVD233-Q1 Functional Block Diagram
RS
CANH
TXD
CANL
EN
RXD
Figure 30. SN65HVD234-Q1 Functional Block Diagram
RS
CANH
TXD
CANL
AB
RXD
Figure 31. SN65HVD235-Q1 Functional Block Diagram
10.3 Feature Description
10.3.1 Diagnostic Loopback (SN65HVD233-Q1)
The diagnostic loopback or internal loopback function of the SN65HVD233-Q1 device is enabled with a high-level
input on pin 5, LBK. This mode disables the driver output while keeping the bus pins biased to the recessive
state. This mode also redirects the TXD data input (transmit data) through logic to the received data output pin,
thus creating an internal loopback of the transmit-to-receive data path. This mimics the loopback that occurs
normally with a CAN transceiver, because the receiver loops back the driven output to the RXD (receive data)
pin. This mode allows the host protocol controller to input and read back a bit sequence or CAN messages to
perform diagnostic routines without disturbing the CAN bus. A typical CAN bus application is displayed in
Figure 37.
18
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
Feature Description (continued)
If the LBK pin is not used, it may be tied to ground (GND). However, it is pulled low internally (defaults to a low-
level input) and may be left open if not in use.
10.3.2 Autobaud Loopback (SN65HVD235-Q1)
The autobaud loopback mode of the SN65HVD235-Q1 device is enabled by placing a high-level input on pin 5,
AB. In autobaud mode, the driver output is disabled, thus blocking the TXD pin-to-bus path and the bus transmit
function of the transceiver. The bus pins remain biased to recessive. The receiver-to-RXD pin path of the device
remains operational, allowing bus activity to be monitored. In addition, the autobaud mode includes an internal
logic loopback path from the TXD pin to the RXD pin so the local node can transmit to itself in sync with bus
traffic while not disturbing messages on the bus. Thus if the CAN controller of the local node generates an error
frame, it is not transmitted to the bus, but is detected only by the local CAN controller. This is especially helpful to
determine if the local node is set to the same baud rate as the network, and if not, to adjust it to the network
baud rate (autobaud detection).
Autobaud detection is best suited to applications that have a known selection of baud rates. For example, if an
application has optional settings of 125 kbps, 250 kbps, or 500 kbps. Once the SN65HVD235-Q1 device is
placed into autobaud loopback mode, the application software could assume the first baud rate of 125 kbps. It
then waits for a message to be transmitted by another node on the bus. If the wrong baud rate has been
selected, an error message is generated by the local CAN controller because the sample times will not be at the
correct time. However, because the bus-transmit function of the device has been disabled, no other nodes
receive the error frame generated by the local CAN controller of this node.
The application would then make use of the status register indications of the local CAN controller for message-
received and error-warning status to determine if the set baud rate is correct or not. The warning status indicates
that the CAN controller error counters have been incremented. A message received status indicates that a good
message has been received. If an error is generated, the application then sets the CAN controller to the next
possibly valid baud rate, and waits to receive another message. This pattern is repeated until an error-free
message has been received, thus the correct baud rate has been selected. At this point, the application places
the SN65HVD235-Q1 device in a normal transmitting mode by setting pin 5 to a low level, thus enabling bus-
transmit and bus-receive functions to normal operating states for the transceiver.
If the AB pin is not used, it may be tied to ground (GND). However, it is pulled low internally (defaults to a low-
level input) and may be left open if not in use.
10.3.3 Slope Control
The rise and fall slope of the SN65HVD233-Q1, SN65HVD234-Q1, and SN65HVD235-Q1 driver output can be
adjusted by connecting a resistor from RS (pin 8) to ground (GND) as shown in Figure 32, or to a low level input
voltage as shown in Figure 33.
The slope of the driver output signal is proportional to the output current of the pin. This slope control is
implemented with an external resistor value of 10 kΩ to achieve an approximately 15-V/µs slew rate, and up to
100 kΩ to achieve an approximately 2-V/μs slew rate. A typical slew-rate versus pulldown-resistance graph is
shown in Figure 34. Typical driver output waveforms with slope control are displayed in Figure 40.
RS
1
2
3
4
8
7
6
5
TXD
GND
VCC
CANH
CANL
LBK
10 kW
to
100 kW
RXD
Figure 32. Ground Connection for Selecting Slope-Control or Standby Mode
RS
1
2
3
4
8
7
6
5
TXD
GND
VCC
CANH
CANL
LBK
10 kW
to
TI Controller
100 kW
RXD
Figure 33. DSP Connection for Selecting Slope-Control or Standby Mode
Copyright © 2016, Texas Instruments Incorporated
19
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
Feature Description (continued)
25
20
15
10
5
0
0
10
20
30
40
50
60
70
80
90 100
Slope Control Resistance (kW)
D012
Figure 34. SN65HVD233-Q1 Driver Output-Signal Slope vs Slope-Control Resistance Value
10.3.4 Standby
If a high-level input (> 0.75 VCC) is applied to RS (pin 8), the circuit enters a low-current, listen only standby
mode during which the driver is switched off and the receiver remains active. If using this mode to save system
power while waiting for bus traffic, the local controller can monitor the RXD output pin for a falling edge which
indicates that a dominant signal was driven onto the CAN bus. The local controller can then drive the RS pin low
to return to slope-control mode or high-speed mode.
10.3.5 Thermal Shutdown
If the junction temperature of the device exceeds the thermal shutdown threshold, the device turns off the CAN
driver circuits, thus blocking the TXD pin-to-bus transmission path. The shutdown condition is cleared when the
junction temperature drops sufficiently below the thermal shutdown temperature of the device. The CAN bus pins
are high-impedance and biased to the recessive level during a thermal shutdown, and the receiver-to-RXD pin
path remains operational.
10.4 Device Functional Modes
Table 2. Driver (SN65HVD233-Q1 or SN65HVD235-Q1)
INPUTS
OUTPUTS
TXD
LBK or AB
RS
CANH
CANL
BUS STATE
Recessive
Dominant
X
X
> 0.75 VCC
Z
H
Z
Z
Z
L
Z
Z
L
H or open
X
L or open
≤ 0.33 VCC
≤ 0.33 VCC
X
H
Recessive
Recessive
Table 3. Driver (SN65HVD234-Q1)
INPUTS
OUTPUTS
TXD
EN
RS
≤ 0.33 VCC
≤ 0.33 VCC
X
CANH
CANL
BUS STATE
Dominant
L
H
H
H
Z
Z
Z
Z
L
Z
Z
Z
Z
X
Recessive
Recessive
Recessive
Recessive
Open
X
X
X
> 0.75 VCC
X
X
L or open
20
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
Table 4. Receiver (SN65HVD233-Q1)(1)
INPUTS
VID = V(CANH) – V(CANL)
VID ≥ 0.9 V
OUTPUT
BUS STATE
LBK
L or open
L or open
L or open
H
TXD
RXD
L
Dominant
X
Recessive
VID ≤ 0.5 V or open
H or open
H
?
X
X
0.5 V < VID < 0.9 V
H or open
?
X
X
L
L
H
H
H
(1) H = high level; L = low level; Z = high impedance; X = irrelevant; ? = indeterminate
Table 5. Receiver (SN65HVD235-Q1)(1)
INPUTS
OUTPUT
BUS STATE
Dominant
Recessive
?
VID = V(CANH)–V(CANL)
ID ≥ 0.9 V
ID ≤ 0.5 V or open
0.5 V < VID <0.9 V
ID ≥ 0.9 V
AB
TXD
RXD
L
V
L or open
X
V
L or open
H or open
H
?
L or open
H or open
Dominant
Recessive
Recessive
?
V
H
H
H
H
X
H
L
L
V
ID ≤ 0.5 V or open
ID ≤ 0.5 V or open
H
L
V
0.5 V < VID <0.9 V
L
L
(1) H = high level; L = low level; Z = high impedance; X = irrelevant; ? = indeterminate
Table 6. Receiver (SN65HVD234-Q1)(1)
INPUTS
OUTPUT
BUS STATE
VID = V(CANH) – V(CANL)
ID≥ 0.9 V
EN
RXD
L
Dominant
V
H
Recessive
VID ≤ 0.5 V or open
0.5 V < VID < 0.9 V
X
H
H
H
?
?
X
L or open
H
(1) H = high level; L = low level; Z = high impedance; X = irrelevant; ? = indeterminate
Copyright © 2016, Texas Instruments Incorporated
21
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
11 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
11.1 Application Information
The CAN bus has two states during powered operation of the device, dominant and recessive. A dominant bus
state is when the bus is driven differentially, corresponding to a logic low on the TXD and RXD pins. A recessive
bus state is when the bus is biased to VCC / 2 via the high-resistance internal resistors RIN and RID of the
receiver, corresponding to a logic high on the TXD and RXD pins. See Figure 35 and Figure 36.
/!bI
Vdiff(D)
Vdiff(R)
/!b[
Çime, t
wecessive
[ogic I
5ominant
[ogic [
wecessive
[ogic I
Figure 35. Bus States (Physical Bit Representation)
CANH
RXD
VCC / 2
CANL
Figure 36. Simplified Recessive Common-Mode Bias and Receiver
These CAN transceivers are typically used in applications with a host microprocessor or FPGA that includes the
link layer portion of the CAN protocol. The different nodes on the network are typically connected through the use
of a 120-Ω characteristic impedance twisted-pair cable with termination on both ends of the bus.
22
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
11.2 Typical Application
Bus Lines -- 40 m max
CANH
120 W
120 W
Stub Lines -- 0.3 m max.
CANL
5 V
3.3 V
3.3 V
VCC
GND
VCC
VCC
0.1 µF
SN65HVD233-Q1
0.1 µF
SN65HVD234-Q1
0.1 µF
TCAN1042-Q1
GND
GND
TXD
RXD
LBK
TXD
RXD
TXD
RXD
CANRX
TI CAN Controller
CANTX CANRX
GPIO CANTX
CANTX CANRX
TI CAN Controller
TI CAN Controller
Copyright © 2016, Texas Instruments Incorporated
Figure 37. Typical SN65HVD233-Q1 Application
11.2.1 Design Requirements
11.2.1.1 Bus Loading, Length and Number of Nodes
The ISO 11898 standard specifies a data rate of up to 1 Mbps, maximum CAN bus cable length of 40 m,
maximum drop line (stub) length of 0.3 m and a maximum of 30 nodes. However, with careful network design,
the system may have longer cables, longer stub lengths, and many more nodes to a bus. Many CAN
organizations and standards have scaled the use of CAN for applications outside the original ISO 11898
standard. They have made system-level trade-offs for data rate, cable length, and parasitic loading of the bus.
Examples of some of these specifications are ARINC825, CANopen, CAN Kingdom, DeviceNet and NMEA200.
A high number of nodes requires a transceiver with high input impedance and wide common-mode range, such
as the SN65HVD23x-Q1 CAN family. ISO 11898-2 specifies the driver differential output with a 60-Ω load (two
120-Ω termination resistors in parallel) and the differential output must be greater than 1.5 V. The SN65HVD23x-
Q1 devices are specified to meet the 1.5-V requirement with a 60-Ω load, and additionally specified with a
differential output voltage minimum of 1.2 V across a common mode range of –2 V to 7 V through a 330-Ω
coupling network. This network represents the bus loading of 120 SN65HVD23x-Q1 transceivers based on their
minimum differential input resistance of 40 kΩ. Therefore, the SN65HVD23x-Q1 devices support up to 120
transceivers on a single bus segment with margin to the 1.2-V minimum differential input-voltage requirement at
each node.
For CAN network design, margin must be given for signal loss across the system and cabling, parasitic loadings,
network imbalances, ground offsets and signal integrity. Thus, a practical maximum number of nodes may be
lower. Bus length may also be extended beyond the original ISO 11898 standard of 40 m by careful system-
design and data-rate tradeoffs. For example, CANopen network design guidelines allow the network to be up to
1 km with changes in the termination resistance, cabling, fewer than 64 nodes, and significantly lowered data
rate.
This flexibility in CAN network design is one of the key strengths of the various extensions and additional
standards that have been built on the original ISO 11898 CAN standard.
11.2.1.2 CAN Termination
The ISO 11898 standard specifies the interconnect to be a twisted-pair cable (shielded or unshielded) with 120-Ω
characteristic impedance (ZO). Resistors equal to the characteristic impedance of the line should be used to
terminate both ends of the cable to prevent signal reflections. Unterminated drop lines (stubs) connecting nodes
to the bus should be kept as short as possible to minimize signal reflections. The termination may be on the
cable or in a node, but if nodes may be removed from the bus the termination must be carefully placed so that it
is not removed from the bus.
Copyright © 2016, Texas Instruments Incorporated
23
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
Typical Application (continued)
11.2.2 Detailed Design Procedure
Node n
(with termination)
Node 1
Node 2
Node 3
MCU or DSP
MCU or DSP
MCU or DSP
MCU or DSP
CAN
Controller
CAN
Controller
CAN
Controller
CAN
Controller
CAN
Transceiver
CAN
Transceiver
CAN
Transceiver
CAN
Transceiver
RTERM
RTERM
Figure 38. Typical CAN Bus
Termination is typically a 120-Ω resistor at each end of the bus. If filtering and stabilization of the common-mode
voltage of the bus is desired, then split termination may be used (see Figure 39). Split termination uses two 60-Ω
resistors with a capacitor in the middle of these resistors to ground. Split termination improves the
electromagnetic emissions behavior of the network by eliminating fluctuations in the bus common-mode voltages
at the start and end of message transmissions.
Care should be taken in the power ratings of the termination resistors used. Typically, the worst-case condition
would be if the system power supply is shorted across the termination resistance to ground. In most cases, the
current flow through the resistor in this condition would be much higher than the transceiver current limit.
Split Termination
Standard Termination
CANH
CANH
R
R
/ 2
TERM
CAN
Transceiver
CAN
Transceiver
R
TERM
C
SPLIT
/ 2
TERM
CANL
CANL
Figure 39. CAN Bus Termination Concepts
11.2.3 Application Curve
Figure 40 shows three typical output waveforms for the SN65HVD233-Q1 device with three different connections
made to the RS pin. The top waveform shows the typical differential signal when transitioning from a recessive
level to a dominant level on the CAN bus with RS tied to GND through a 0-Ω resistor. The second waveform
shows the same signal for the condition with a 10-kΩ resistor tied from RS to ground. The bottom waveform
shows the typical differential signal for the case where a 100-kΩ resistor is tied from the RS pin to ground.
24
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
Typical Application (continued)
Rs = 0 W
Rs = 10 kW
Rs = 100 kW
Figure 40. Typical SN65HVD233-Q1 Output Waveforms With Different Slope-Control Resistor Values
11.3 System Example
11.3.1 ISO 11898 Compliance of SN65HVD23x-Q1 Family of 3.3-V CAN Transceivers
11.3.1.1 Introduction
Many users value the low power consumption of operating their CAN transceivers from a 3.3-V supply. However,
some are concerned about the interoperability with 5-V-supplied transceivers on the same bus. This report
analyzes this situation to address those concerns.
11.3.1.2 Differential Signal
CAN is a differential bus where complementary signals are sent over two wires and the voltage difference
between the two wires defines the logical state of the bus. The differential CAN receiver monitors this voltage
difference and outputs the bus state with a single-ended logic-level output signal.
NOISE MARGIN
900 mV Threshold
RECEIVER DETECTION WINDOW
75% SAMPLE POINT
500 mV Threshold
NOISE MARGIN
Figure 41. Typical Differential-Output-Voltage Waveform
Copyright © 2016, Texas Instruments Incorporated
25
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
System Example (continued)
The CAN driver creates the differential voltage between CANH and CANL in the dominant state. The dominant
differential output of the SN65HVD23x-Q1 device is greater than 1.5 V and less than 3 V across a 60-Ω load as
defined by the ISO 11898 standard. These are the same limiting values as for 5-V-supplied CAN transceivers.
The bus termination resistors, and not the CAN driver, drive the bus to the recessive state.
A CAN receiver is required to output a recessive state when less than 500 mV of differential voltage exists on the
bus, and a dominant state when more than 900 mV of differential voltage exists on the bus. The CAN receiver
must do this with common-mode input voltages from –2 V to 7 V. The SN65HVD23x-Q1 family of receivers
meets these same input specifications as 5-V-supplied receivers do.
11.3.1.3 Common-Mode Signal
The differential receiver rejects the common-mode signal, which is the average of the two CAN signals. The
common-mode signal comes from the CAN driver, ground noise, and coupled bus noise. Because the bias
voltage of the recessive state of the device is dependent on VCC, any noise present or any variation of VCC has
an effect on this bias voltage seen by the bus. The SN65HVD23x-Q1 family has the recessive bias voltage set
higher than 0.5 × VCC to comply with the ISO 11898-2 CAN standard. The caveat to this is that the common-
mode voltage drops by a approximately 200 millivolts when driving a dominant bit on the bus. This means that
there is a common-mode shift between the dominant-bit and recessive-bit states of the device. Although this is
not ideal, this small variation in the driver common-mode output is rejected by differential receivers and does not
affect data, signal noise margins, or error rates.
11.3.1.4 Interoperability of 3.3-V CAN in 5-V CAN Systems
The 3.3-V-supplied SN65HVD23x-Q1 family of CAN transceivers is fully compatible with 5-V CAN transceivers.
The differential output voltage is the same, the recessive common-mode output bias is the same, and the
receivers have the same input specifications. The only slight difference is in the dominant common-mode output
voltage, which is aapproximately 200 millivolts lower for a 3.3-V CAN transceiver than for a 5-V-supplied
transceiver.
To help ensure the widest interoperability possible, the SN65HVD23x-Q1 family has successfully passed the
internationally recognized GIFT/ICT conformance and interoperability testing for CAN transceivers. Electrical
interoperability does not always assure interchangeability, however. Most implementers of CAN buses recognize
that ISO 11898 does not sufficiently specify the electrical layer and that strict standard compliance alone does
not ensure full interchangeability. This comes only with thorough equipment testing.
12 Power Supply Recommendations
To ensure reliable operation at all data rates and supply voltages, each supply should be decoupled with a
100‑nF ceramic capacitor located as close to the VCC supply pins as possible. The TPS76333-Q1 is a linear
voltage regulator suitable for the 3.3 V supply.
13 Layout
13.1 Layout Guidelines
In order for the PCB design to be successful, start with design of the protection and filtering circuitry. Because
ESD and EFT transients have a wide frequency bandwidth from approximately 3 MHz to 3 GHz, high-frequency
layout techniques must be applied during PCB design. On-chip IEC ESD protection is good for laboratory and
portable equipment but is usually not sufficient for EFT and surge transients occurring in industrial environments.
Therefore, robust and reliable bus node design requires the use of external transient protection devices at the
bus connectors. Placement at the connector also prevents these harsh transient events from propagating further
into the PCB and system.
Use VCC and ground planes to provide low inductance.
26
Copyright © 2016, Texas Instruments Incorporated
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
www.ti.com.cn
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
Layout Guidelines (continued)
NOTE
High-frequency current follows the path of least inductance and not the path of least
resistance.
Design bus protection by placing the protective components in the signal path. Do not force the transient current
to divert from the signal path to reach the protection device.
An example placement of the transient-voltage-suppression (TVS) device indicated as D1 (either bidirectional
diode or varistor solution) and bus filter capacitors C8 and C9 is shown in Figure 42.
The bus transient protection and filtering components should be placed as close to the bus connector,
J1, as possible. This prevents transients, ESD and noise from penetrating onto the board and disturbing
other devices.
Bus termination: Figure 42 shows split termination. This is where the termination is split into two resistors, R5
and R6, with the center or split tap of the termination connected to ground via capacitor C7. Split termination
provides common-mode filtering for the bus. When termination is placed on the board instead of directly on the
bus, care must be taken to ensure the terminating node is not removed from the bus, as there are signal integrity
issues if the bus is not properly terminated on both ends. See the Detailed Design Procedure section for
information on power ratings needed for the termination resistor(s).
Bypass and bulk capacitors should be placed as close as possible to the supply pins of the transceiver, as in the
example of C2 and C3 on VCC
.
Use at least two vias for the VCC and ground connections of the bypass capacitors and protection devices to
minimize trace and via inductance.
To limit current on the digital lines, serial resistors may be used. Examples are R1, R2, R3 and R4.
To filter noise on the digital I/O lines, a capacitor may be used close to the input side of the I/O as shown by C1
and C4.
Because the internal pullup and pulldown biasing of the device is weak for floating pins, an external 1-kΩ to
10‑kΩ pullup or pulldown resistor should be used to bias the state of the pin more strongly against noise during
transient events.
Pin 1: If an open-drain host processor is used to drive the TXD pin of the device, an external pullup resistor
between 1 kΩ and 10 kΩ to VCC should be used to drive the recessive input state of the device.
Pin 8: The mode pin, RS, is shown, assuming that it is used in the application. If the device is only to be used in
normal mode or slope-control mode, R3 is not needed and the pads of C4 could be used for the pulldown
resistor to GND.
13.2 Layout Example
RS
TXD
RXD
Figure 42. Layout Example Diagram
版权 © 2016, Texas Instruments Incorporated
27
SN65HVD233-Q1, SN65HVD234-Q1, SN65HVD235-Q1
ZHCSFG5A –SEPTEMBER 2016–REVISED NOVEMBER 2016
www.ti.com.cn
14 器件和文档支持
14.1 相关链接
以下表格列出了快速访问链接。范围包括技术文档、支持与社区资源、工具和软件,并且可以快速访问样片或购买
链接。
表 7. 相关链接
器件
产品文件夹
请单击此处
请单击此处
请单击此处
样片与购买
请单击此处
请单击此处
请单击此处
技术文档
请单击此处
请单击此处
请单击此处
工具与软件
请单击此处
请单击此处
请单击此处
支持与社区
请单击此处
请单击此处
请单击此处
SN65HVD233-Q1
SN65HVD234-Q1
SN65HVD235-Q1
14.2 接收文档更新通知
如需接收文档更新通知,请访问 ti.com 上的器件产品文件夹。点击右上角的提醒我 (Alert me) 注册后,即可每周定
期收到已更改的产品信息。有关更改的详细信息,请查阅已修订文档中包含的修订历史记录。
14.3 社区资源
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
14.4 商标
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
14.5 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
14.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
15 机械、封装和可订购信息
以下页中包括机械、封装和可订购信息。这些信息是针对指定器件可提供的最新数据。本数据随时可能发生变更并
且不对本文档进行修订,恕不另行通知。要获得这份数据表的浏览器版本,请查阅左侧的导航窗格。
28
版权 © 2016, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
SN65HVD233QDRQ1
SN65HVD234QDRQ1
SN65HVD235QDRQ1
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500 RoHS & Green
2500 RoHS & Green
2500 RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
233Q
234Q
235Q
NIPDAU
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Jul-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
SN65HVD233QDRQ1
SN65HVD234QDRQ1
SN65HVD235QDRQ1
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
330.0
330.0
330.0
12.4
12.4
12.4
6.4
6.4
6.4
5.2
5.2
5.2
2.1
2.1
2.1
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Jul-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
SN65HVD233QDRQ1
SN65HVD234QDRQ1
SN65HVD235QDRQ1
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
340.5
340.5
340.5
336.1
336.1
336.1
25.0
25.0
25.0
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com.cn/zh-cn/legal/termsofsale.html) 或 ti.com.cn 上其他适用条款/TI 产品随附的其他适用条款
的约束。TI 提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2021 德州仪器半导体技术(上海)有限公司
相关型号:
©2020 ICPDF网 联系我们和版权申明