SN65LBC031D [TI]
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS; 高速控制器区域网络（CAN ）收发器
| 型号： | SN65LBC031D |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS |
| 文件： | 总17页 (文件大小：825K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
D PACKAGE
(TOP VIEW)
SN75LBC031 Meets Standard ISO/DIS
11898 (up to 500 k Baud)
Driver Output Capability at 50 mA
TX
ASC
1
2
3
4
8
7
6
5
GND
CANH
CANL
REF
Wide Positive and Negative Input/output
Bus Voltage Range
V
CC
RX
Bus Outputs Short-Circuit-Protected to
Battery Voltage and Ground
TERMINAL FUNCTIONS
DESCRIPTION
Thermal Shutdown
TERMINAL
Available in Q-Temp Automotive
TX
Transmitter input
Ground
– HighRel Automotive Applications
– Configuration Control/Print Support
– Qualification to Automotive Standards
GND
V
CC
Supply voltage
RX
Receiver output
Reference output
Low side bus output driver
description
REF
CANL
The SN75LBC031 is a CAN transceiver used as
an interface between a CAN controller and the
physical bus for high speed applications of up to
500 kBaud. The device provides transmit
capability to the differential bus and differential
receive capability to the controller. The transmitter
outputs (CANH and CANL), feature internal
transition regulation to provide controlled
symmetry resulting in low EMI emissions. Both
CANH
ASC
High side bus output driver
Adjustable slope control
FUNCTION TABLE
TX
CANH
CANL BUS STATE RX
L
H
L
Dominant
L
High or floating Floating Floating Recessive
L = low, H = high
H
transmitter outputs are fully protected against battery short circuits and electrical transients that can occur on
the bus lines. In the event of excessive device power dissipation the output drivers are disabled by the thermal
shutdown circuitry at a junction temperature of approximately 160°C. The inclusion of an internal pullup resistor
on the transmitter input ensures a defined output during power up and protocol controller reset. For normal
operation at 500 kBaud the ASC terminal is open or tied to GND. For slower speed operation at 125 kBaud the
busoutputtransitiontimescanbeincreasedtoreduceEMIbyconnectingtheASCterminaltoV . The receiver
CC
includes an integrated filter that suppresses the signal into pulses less than 30 ns wide.
The SN75LBC031 is characterized for operation from –40°C to 85°C. The SN65LBC031 is characterized for
operation from –40°C to 125°C. The SN65LBC031Q is characterized for operation over the automotive
temperature range of –40°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
logic diagram
V
CC
ASC
TX
R
R
R3
CANH
CANL
R2
R1
R1
2R
2R
REF
RX
R
R
GND
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Logic supply voltage, V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
CC
Bus terminal voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –5 V to 20 V
Input current at TX and ASC terminal, I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
I
Input voltage at TX and ASC terminal, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 × V
I
CC
Operating free-air temperature range, T : SN65LBC031, SN65LBC031Q . . . . . . . . . . . . . . . –40°C to125°C
A
SN75LBC031 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
Operating juncation range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 150°C
J
Continuous total power dissipation at (or below) 25°C free-air temperature . . See Dissipation Rating Table
Storage temperature range, T
Case temperature for 10 sec T , D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values, except differential bus voltage, are measured with respect to GND.
DISSIPATION RATING TABLE
T
≤ 25°C
OPERATING FACTOR
T = 125°C
C
POWER RATING
A
PACKAGE
POWER RATING
ABOVE T = 25°C
C
D
725 mW
5.8 mW/°C
145 mW
DISSIPATION DERATING CURVE
vs
FREE-AIR TEMPERATURE
1200
1000
800
T
C
= 25°C
P = 8.8 mW/°C
600
D = 5.8 mW/°C
400
200
0
25
45
65
85
105 125
115
35
55
75
95
T
A
– Free-Air Temperature – °C
Figure 1
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
recommended operating conditions
MIN NOM
MAX
5.5
7
UNIT
V
Logic supply voltage, V
CC
4.5
–2
2
5
Voltage at any bus terminal (separately or common mode), V or V (see Note 3)
IC
V
I
High-level input voltage, V
IH
TX
V
CC
0.8
V
Low-level input voltage, V
TX
0
V
IL
Transmitter
Receiver
Transmitter
Receiver
SN75LBC031
–50
–400
50
mA
µA
High-level output current, I
OH
Low-level output current, I
mA
OL
1
–40
–40
85
Operating free-air temperature, T
°C
A
SN65LBC031, SN65LBC031Q
125
NOTES: 2. All voltage values, except differential bus voltage, are measured with respect to the ground terminal.
3. For bus voltages from –5 V to –2 V and 7 V to 20 V the receiver output is stable.
SYMBOL DEFINITION
DATA SHEET PARAMETER
DEFINITION
V
V
V
V
V
V
V
CANH bus output voltage (recessive state)
CANL bus output voltage (recessive state)
CANH bus output voltage (dominant state)
CANL bus output voltage (dominant state)
Bus differential output voltage (recessive state)
Bus differential output voltage (dominant state)
Adjustable slope control input voltage
O(CANHR)
O(CANLR)
O(CANHD)
O(CANLD)
O(DIFFR)
O(DIFFD)
I(ASC)
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
= ±20 µA
MIN
TYP
MAX
UNIT
V
V
Reference source output voltage
Reference source output resistance
Logic supply current, recessive state
Logic supply current, dominant state
I
0.45V
5
0.55V
10
O(REF)
REF
CC
CC
R
kΩ
O(REF)
CC(REC)
CC(DOM)
I
I
12
55
20
See Figure 2, S1 closed
mA
80
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
transmitter electrical characteristics over recommended ranges of supply and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
V
V
O(CANHR)
O(CANLR)
Output voltage (recessive state)
2
0.5V
CC
3
V
See Figure 2,
S1 open
V
V
V
V
Differential output voltage (recessive state)
Output voltage (dominant state)
–500
2.75
0.5
0
3.5
50
4.5
mV
O(DIFFR)
O(CANHD)
O(CANLD)
O(DIFFD)
Output voltage (dominant state)
See Figure 2,
S1 closed
1.5
2.25
3
V
Differential output voltage (dominant state)
1.5
2
V
V
V
V
V
V
= 2.4 V
–100
–185
±2
IH
IH
IH
IH
IL
I
High-level input current (TX)
High-level input current (ASC)
µA
µA
IH(TX)
= V
CC
= 2.4 V
= V
100
200
–180
15
165
340
–400
25
I
IH(ASC)
CC
I
I
Low-level input current (TX)
Low-level input current (ASC)
TX input capacitance
= 0.4 V
= 0.4 V
µA
µA
pF
IL(TX)
IL(ASC)
IL
C
8
I(TX)
I
CANH short circuit output current
CANL short circuit output current
V
V
= –2 V to 20 V
= 20 V to –2 V
–95
140
–200
250
mA
mA
O(ssH)
O(ssL)
O(CANH)
I
O(CANL)
NOTE 2: All voltage values, except differential bus voltage, are measured with respect to the ground terminal.
transceiver dynamic characteristics over recommended operating free-air temperature range and
= 5 V
V
CC
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
See Figures 2 and 3,
S1 closed,
V
= 0 V or open circuit,
I(ASC)
S2 open
280
ns
t
Loop time
(loop)
See Figures 2 and 3,
S1 closed,
V
= V
,
CC
I(ASC)
S2 closed
400
ns
See Figures 2 and 4,
S1 closed,
V
= 0 or open circuit,
I(ASC)
S2 open
35
10
10
10
V/µs
V/µs
V/µs
V/µs
Differential-output slew rate
(recessive to dominant)
SR
SR
(RD)
See Figures 2 and 4,
S1 closed,
V
= V
,
CC
I(ASC)
S2 closed
See Figures 2 and 4,
S1 closed,
V
= 0 or open circuit,
I(ASC)
S2 open
Differential-output slew rate
(dominant to recessive)
(DR)
See Figures 2 and 4,
S1 closed,
V
= V
,
CC
I(ASC)
S2 closed
t
t
t
t
55
160
90
ns
ns
ns
ns
d(RD)
Differential-output delay time
See Figure 2,
S1 closed
d(DR)
Receiver propagation delay
time
pd(RECRD)
pd(RECDR)
See Figures 2 and 5
55
NOTE 4: Receiver input pulse width should be >50 ns. Input pulses of <30 ns are suppressed.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
receiver electrical characteristics over recommended ranges of common-mode input voltage,
supply voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
V
V
V
Differential input threshold voltage for recessive state
Differential input threshold voltage for dominant state
Recessive-dominant input hysteresis
500
IT(REC)
IT(DOM)
hys
V
= –2 V to 7 V
mV
IC
900
100
180
mV
V
V
= 500 mV,
= –400 µA
O(DIFF)
O(DIFF)
V
High-level output voltage
V
–0.5 V
V
CC
OH(RX)
CC
I
OH
V
= 900 mV,
= 1 mA
V
Low-level output voltage
0
5
0.5
50
V
OL(RX)
I(REC)
I(DIFF)
I
OL
r
r
CANH and CANL input resistance in recessive state
dc, no load
kΩ
kΩ
Differential CANH and CANL input resistance in recessive
state
dc, no load
10
100
C
C
CANH and CANL input capacitance
20
10
pF
pF
i
Differential CANH and CANL input capacitance
i(DHL)
NOTE 2: All voltage values, except differential bus voltage, are measured with respect to the ground terminal.
PARAMETER MEASUREMENT INFORMATION
S2
V
CC
60 Ω
60 Ω
ASC
CANH
CANL
S1
TX Input
V
DIFF
Generator
(see Note A)
56 pF
60 Ω
60 Ω
56 pF
15 pF
R
RX Output
NOTE A: The input pulse is supplied to TX by a generator having a t and t = 5 ns.
r
f
Figure 2. Test Circuit
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
PARAMETER MEASUREMENT INFORMATION
3 V
3 V
0 V
TX Input
1.5 V
TX Input
1.5 V
0 V
V
V
OH
90%
V
OH
80%
80%
RX Output
10%
V
O(DIFF)
20%
20%
OL
V
OL
t
loop
t
SR(DR)
loop
SR(RD)
Figure 3. Loop Time
Figure 4. Slew Rate
NOTE A: The input pulse is supplied to TX by a generator having a t and t = 5 ns.
r
f
0.9 V
V
O(DIFF)
0.5 V
90%
RX Output
10%
t
pd(RECDR)
t
pd(RECRD)
NOTE A: The input pulse is supplied as V
using CANH and CANL
DIFF
respectively by a generator having a t and t = 5 ns.
r
f
Figure 5. Receiver Delay Times
100 pF
Transient Source
(Schaffner Generator)
CANH
CANL
R
(SOURCE)
60 Ω
100 pF
V
S
Figure 6. Transient Stress Capability Test Circuit
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
PARAMETER MEASUREMENT INFORMATION
Transient Magnitude
vs
Time
V
S
90%
10%
0 V
t – Time
t
r
t
d
t
2
t
1
Figure 7. Transient Stress Capability Waveform
Table 1. Test Circuit Results According to DIN 40839
TRANSIENT
MAGNITUDE
SOURCE
IMPEDANCE
PULSE WIDTH
PULSE RISE
TIME, t
(see Note 6)
PULSE TIME,
REPETITION
PERIOD, t
NUMBER OF
PULSES
TEST PULSE
t
t
2
d
r
1
V
S
R
(see Note 5)
(see Figure 7) (see Figure 7)
SOURCE
1
2
–100 V
100 V
–150 V
100 V
60 V
10 Ω
2 ms
1 µs
200 ms
200 ms
100 µs
100 µs
—
5 s
5 s
5000
5000
10 Ω
50 Ω
50 Ω
1 Ω
50 µs
1 µs
3a
3b
5
0.1 µs
5 ns
100 µs
100 µs
—
See Note 7
See Note 7
1
0.1 µs
5 ns
400 ms
5 ms
NOTES: 5. Measured from 10% on rising edge to 10% on falling edge
6. Measured from 10% to 90% of pulse
7. Pulse package for a period of 3600 s, 10 ms pulse time, 90 ms stop time
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
APPLICATION INFORMATION
5 V
100 nF
3
120 Ω
8
10 kΩ
10 kΩ
V
CC
V
CC
TL7705B
8
2
ASC
7
6
CANH
CANL
7
2
3
SENSE
RESIN
SN75LBC031
5
RESET
GND
TX
C
t
REF GND
C
in
1
4
REF
RX
4
120 Ω
1
5
0.1 µF
CAN Microcontroller
Figure 8. Typical SN75LBC031 Application
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
0.010 (0,25)
M
14
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°–8°
0.044 (1,12)
0.016 (0,40)
A
Seating Plane
0.004 (0,10)
0.010 (0,25)
0.004 (0,10)
0.069 (1,75) MAX
PINS **
8
14
16
DIM
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MAX
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
A MIN
4040047/D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
SN65LBC031D
ACTIVE
SOIC
SOIC
D
8
8
75
TBD
CU NIPDAU
CU NIPDAU
Level-1-220C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
6LB031
SN65LBC031DG4
ACTIVE
ACTIVE
D
D
75
Green (RoHS
& no Sb/Br)
6LB031
6LB031
SN65LBC031DRG4
SOIC
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC031P
SN75LBC031D
OBSOLETE
ACTIVE
PDIP
SOIC
P
D
8
8
TBD
Call TI
Call TI
-40 to 85
0 to 70
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
7LB031
7LB031
SN75LBC031DR
SN75LBC031P
ACTIVE
SOIC
PDIP
D
P
8
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Call TI
Level-1-260C-UNLIM
Call TI
0 to 70
0 to 70
OBSOLETE
TBD
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
SN75LBC031DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SOIC
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
SN75LBC031DR
D
8
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明