SN74AVC16373DGVR [TI]
具有三态输出的 16 位透明 D 型锁存器 | DGV | 48 | -40 to 85;
| 型号： | SN74AVC16373DGVR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有三态输出的 16 位透明 D 型锁存器 | DGV | 48 | -40 to 85 驱动 光电二极管 逻辑集成电路 锁存器 总线驱动器 总线收发器 |
| 文件： | 总11页 (文件大小：169K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
Member of the Texas Instruments
Widebus Family
I
Supports Partial-Power-Down Mode
off
Operation
EPIC (Enhanced-Performance Implanted
CMOS) Submicron Process
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
DOC (Dynamic Output Control) Circuit
Dynamically Changes Output Impedance,
Resulting in Noise Reduction Without
Speed Degradation
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
Package Options Include Plastic Thin
Shrink Small-Outline (DGG) and Thin Very
Small-Outline (DGV) Packages
Dynamic Drive Capability Is Equivalent to
Standard Outputs With I
and I
of
OH
OL
±24 mA at 2.5-V V
CC
Overvoltage-Tolerant Inputs/Outputs Allow
Mixed-Voltage-Mode Data Communications
description
A Dynamic Output Control (DOC) circuit is implemented, which, during the transition, initially lowers the output
impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1
shows typical V vs I and V
vs I
curves to illustrate the output impedance and drive capability of the
OL
OL
OH
OH
circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is
equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC
Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC )
Circuitry Technology and Applications, literature number SCEA009.
3.2
T
= 25°C
T
= 25°C
A
A
Process = Nominal
Process = Nominal
2.8
2.4
2.0
2.8
2.4
2.0
V
= 3.3 V
CC
1.6
1.2
0.8
0.4
1.6
1.2
0.8
0.4
V
= 2.5 V
CC
V
= 1.8 V
CC
V
= 3.3 V
V
= 2.5 V
CC
CC
V
= 1.8 V
CC
–160 –144 –128 –112 –96 –80 –64 –48 –32 –16
– Output Current – mA
0
17
34
51
68
85 102 119 136 153 170
0
I
– Output Current – mA
I
OH
OL
Figure 1. Output Voltage vs Output Current
This 16-bit transparent D-type latch is operational at 1.2-V to 3.6-V V , but is designed specifically for 1.65-V
CC
to 3.6-V V
operation.
CC
The SN74AVC16373 is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus
drivers, and working registers. This device can be used as two 8-bit latches or one 16-bit latch. When the
latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs
are latched at the levels set up at the D inputs.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
DOC, EPIC, and Widebus are trademarks of Texas Instruments Incorporated.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
description (continued)
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high
or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive
the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus
lines without need for interface or pullup components. OE does not affect internal operations of the latch. Old
data can be retained or new data can be entered while the outputs are in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to V through a pullup
CC
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using I . The I circuitry disables the outputs,
off
off
preventing damaging current backflow through the device when it is powered down.
The SN74AVC16373 is characterized for operation from –40°C to 85°C.
terminal assignments
DGG OR DGV PACKAGE
(TOP VIEW)
1OE
1Q1
1Q2
GND
1Q3
1Q4
1LE
1D1
1D2
GND
1D3
1D4
1
2
3
4
5
6
7
8
9
48
47
46
45
44
43
42
41
40
V
V
CC
CC
1Q5
1Q6
1D5
1D6
GND 10
39 GND
1Q7
1Q8
1D7
1D8
11
12
38
37
2Q1 13
2Q2 14
GND 15
2Q3 16
2Q4 17
36 2D1
35 2D2
34 GND
33 2D3
32 2D4
V
18
31
V
CC
CC
2Q5 19
2Q6 20
GND 21
2Q7 22
2Q8 23
2OE 24
30 2D5
29 2D6
28 GND
27 2D7
26 2D8
25 2LE
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
FUNCTION TABLE
(each 8-bit latch)
INPUTS
OUTPUT
Q
LE
H
H
L
D
H
L
OE
L
H
L
L
L
X
X
Q
0
H
X
Z
†
logic symbol
1
1OE
1LE
2OE
2LE
1EN
C3
48
24
25
2EN
C4
47
46
44
43
41
40
38
37
36
35
33
32
30
29
27
26
2
3
1D1
1D2
1D3
1D4
1D5
1D6
1D7
1D8
2D1
2D2
2D3
2D4
2D5
2D6
2D7
2D8
3D
1
1Q1
1Q2
1Q3
1Q4
1Q5
1Q6
1Q7
1Q8
2Q1
2Q2
2Q3
2Q4
2Q5
2Q6
2Q7
2Q8
5
6
8
9
11
12
13
14
16
17
19
20
22
23
4D
2
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
logic diagram (positive logic)
1
24
25
2OE
2LE
1OE
48
1LE
C1
1D
C1
2
13
2Q1
1Q1
47
36
2D1
1D1
1D
To Seven Other Channels
To Seven Other Channels
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V
CC
Input voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V
I
Voltage range applied to any output in the high-impedance or power-off state, V
O
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V
Voltage range applied to any output in the high or low state, V
O
(see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to V
+ 0.5 V
CC
Input clamp current, I (V < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
(V < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
Continuous output current, I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θ (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W
IK
I
Output clamp current, I
OK
O
O
Continuous current through each V
CC
JA
DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
2. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed.
3. The package thermal impedance is calculated in accordance with JESD 51.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
recommended operating conditions (see Note 4)
MIN
1.4
MAX
UNIT
Operating
3.6
V
Supply voltage
V
CC
IH
Data retention only
1.2
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
= 1.2 V
V
CC
= 1.4 V to 1.6 V
= 1.65 V to 1.95 V
= 2.3 V to 2.7 V
= 3 V to 3.6 V
= 1.2 V
0.65 × V
CC
V
High-level input voltage
0.65 × V
V
V
CC
1.7
2
GND
0.35 × V
0.35 × V
0.7
= 1.4 V to 1.6 V
= 1.65 V to 1.95 V
= 2.3 V to 2.7 V
= 3 V to 3.6 V
CC
CC
V
IL
Low-level input voltage
0.8
V
V
Input voltage
0
0
0
3.6
V
V
I
Active state
3-state
V
CC
3.6
Output voltage
O
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
= 1.4 V to 1.6 V
= 1.65 V to 1.95 V
= 2.3 V to 2.7 V
= 3 V to 3.6 V
–2
–4
–8
†
I
Static high-level output current
mA
mA
OHS
OLS
–12
2
= 1.4 V to 1.6 V
= 1.65 V to 1.95 V
= 2.3 V to 2.7 V
= 3 V to 3.6 V
4
†
I
Static low-level output current
8
12
5
∆t/∆v
Input transition rise or fall rate
Operating free-air temperature
= 1.4 V to 3.6 V
ns/V
T
–40
85
°C
A
†
DynamicdrivecapabilityisequivalenttostandardoutputswithI
OH
andI of±24mAat2.5-VV .SeeFigure1forV vsI andV vs I
OL CC OL OL OH OH
characteristics. Refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and
Dynamic Output Control (DOC ) Circuitry Technology and Applications, literature number SCEA009.
NOTE 4: All unused inputs of the device must be held at V
or GND to ensure proper device operation. Refer to the TI application report,
CC
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
†
PARAMETER
TEST CONDITIONS
= –100 µA
MIN TYP
V –0.2
CC
MAX
UNIT
V
CC
I
I
I
I
I
I
I
I
I
I
1.4 V to 3.6 V
1.4 V
OHS
OHS
OHS
OHS
OHS
OLS
OLS
OLS
OLS
OLS
= –2 mA,
= –4 mA,
= –8 mA,
= –12 mA,
= 100 µA
= 2 mA,
V
V
V
V
= 0.91 V
= 1.07 V
= 1.7 V
= 2 V
1.05
1.2
IH
IH
IH
IH
V
1.65 V
2.3 V
V
OH
OL
1.75
2.3
3 V
1.4 V to 3.6 V
1.4 V
0.2
0.4
V
IL
V
IL
V
IL
V
IL
= 0.49 V
= 0.57 V
= 0.7 V
= 0.8 V
V
= 4 mA,
1.65 V
2.3 V
0.45
0.55
0.7
V
= 8 mA,
= 12 mA,
3 V
I
I
I
I
Control inputs
V = V or GND
CC
3.6 V
±2.5
±10
±10
40
µA
µA
µA
µA
I
I
V or V = 3.6 V
0
off
I
O
V
O
= V or GND
CC
3.6 V
OZ
CC
V = V
I
or GND,
I = 0
O
3.6 V
CC
2.5 V
3
3
Control inputs
Data inputs
Outputs
V = V
I
or GND
CC
3.3 V
C
C
pF
pF
i
2.5 V
2.5
2.5
6.5
6.5
V = V
or GND
I
CC
3.3 V
2.5 V
V
O
= V
or GND
o
CC
3.3 V
†
Typical values are measured at V
= 2.5 V and 3.3 V, T = 25°C.
CC
A
timing requirements over recommended operating free-air temperature range (unless otherwise
noted) (see Figures 2 through 5)
V
= 1.5 V
V
= 1.8 V
V
= 2.5 V
V
= 3.3 V
CC
± 0.1 V
CC
± 0.15 V
CC
± 0.2 V
CC
± 0.3 V
V
= 1.2 V
MAX
CC
UNIT
MIN
MIN
MAX
MIN
2.2
1.1
1.1
MAX
MIN
2
MAX
MIN
1.8
0.8
1
MAX
t
w
t
su
t
h
Pulse duration, LE high
Setup time, data before LE↓
Hold time, data after LE↓
ns
ns
ns
1.7
2
1.2
1.1
0.9
1.1
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figures 2 through 5)
V
= 1.5 V
V
= 1.8 V
V
= 2.5 V
V
= 3.3 V
CC
± 0.1 V
CC
± 0.15 V
CC
± 0.2 V
CC
± 0.3 V
V
CC
= 1.2 V
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
UNIT
TYP
MIN
1.2
1.4
1.6
2.5
MAX
6.8
MIN
1
MAX
5.7
MIN
0.8
0.8
1.4
1.3
MAX
3.3
4
MIN
0.7
0.7
0.7
1.2
MAX
2.8
D
5.8
7.2
7.4
8.4
t
pd
Q
ns
LE
OE
OE
8.3
1.1
1.6
2.3
6.6
3.2
t
t
Q
Q
8.8
6.7
4.3
4.2
3.4
ns
ns
en
9.4
7.8
3.9
dis
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
operating characteristics, T = 25°C
A
V
= 1.8 V
CC
TYP
V
= 2.5 V
CC
TYP
V
= 3.3 V
CC
TYP
PARAMETER
TEST CONDITIONS
UNIT
Outputs enabled
Outputs disabled
40
20
43
22
47
24
Power dissipation
capacitance
C
C
= 0,
L
f = 10 MHz
pF
pd
PARAMETER MEASUREMENT INFORMATION
V
= 1.2 V AND 1.5 V ± 0.1 V
CC
2 × V
CC
Open
S1
2 kΩ
From Output
Under Test
TEST
S1
Open
2 × V
GND
t
pd
/t
C
= 15 pF
t
L
PLZ PZL
CC
GND
2 kΩ
(see Note A)
t
/t
PHZ PZH
LOAD CIRCUIT
t
w
V
CC
V
CC
V
CC
/2
V
CC
/2
Input
Timing
Input
V
/2
CC
0 V
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
t
t
h
su
V
CC
Output
Control
(low-level
enabling)
Data
Input
V
CC
V
/2
V
CC
/2
CC
V
CC
/2
V
CC
/2
0 V
0 V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
t
t
PZL
PLZ
Output
Waveform 1
V
CC
V
CC
V
CC
/2
Input
V
CC
/2
V
CC
/2
S1 at 2 × V
(see Note B)
V
+ 0.1 V
OL
CC
V
0 V
OL
t
t
PZH
PHZ
– 0.1 V
t
t
PLH
PHL
Output
Waveform 2
S1 at GND
V
OH
V
V
OH
V
OH
V
CC
/2
Output
V
CC
/2
V
/2
CC
0 V
OL
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A.
C
includes probe and jig capacitance.
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Z = 50 Ω, t ≤ 2 ns, t ≤ 2 ns.
O
r
f
D. The outputs are measured one at a time with one transition per measurement.
E.
F.
G.
t
t
t
and t
and t
and t
are the same as t
are the same as t
are the same as t
.
dis
en
.
pd
PLZ
PZL
PLH
PHZ
PZH
PHL
.
Figure 2. Load Circuit and Voltage Waveforms
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
PARAMETER MEASUREMENT INFORMATION
= 1.8 V ± 0.15 V
V
CC
2 × V
CC
Open
S1
1 kΩ
From Output
Under Test
TEST
S1
GND
t
Open
pd
/t
C
= 30 pF
t
2 × V
CC
GND
L
PLZ PZL
1 kΩ
(see Note A)
t
/t
PHZ PZH
LOAD CIRCUIT
t
w
V
CC
V
CC
V
CC
/2
V
CC
/2
Input
Timing
Input
V
/2
CC
0 V
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
t
t
h
su
V
CC
Output
Control
(low-level
enabling)
Data
Input
V
CC
V
/2
V
CC
/2
CC
V
CC
/2
V
CC
/2
0 V
0 V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
t
t
PZL
PLZ
Output
Waveform 1
V
CC
V
CC
V
/2
CC
Input
V
CC
/2
V
CC
/2
S1 at 2 × V
(see Note B)
V
V
+ 0.15 V
V
CC
OL
0 V
OL
t
t
PZH
PHZ
t
t
PLH
PHL
Output
Waveform 2
S1 at GND
V
OH
V
V
OH
– 0.15 V
OH
V
/2
CC
Output
V
CC
/2
V
CC
/2
0 V
OL
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A.
C
includes probe and jig capacitance.
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Z = 50 Ω, t ≤ 2 ns, t ≤ 2 ns.
O
r
f
D. The outputs are measured one at a time with one transition per measurement.
E.
F.
G.
t
t
t
and t
and t
and t
are the same as t
are the same as t
are the same as t
.
dis
en
.
pd
PLZ
PZL
PLH
PHZ
PZH
PHL
.
Figure 3. Load Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
PARAMETER MEASUREMENT INFORMATION
V
= 2.5 V ± 0.2 V
CC
2 × V
CC
Open
GND
S1
500 Ω
From Output
Under Test
TEST
S1
t
Open
pd
/t
C
= 30 pF
t
2 × V
CC
GND
L
PLZ PZL
500 Ω
(see Note A)
t
/t
PHZ PZH
LOAD CIRCUIT
t
w
V
CC
V
CC
V
CC
/2
V
CC
/2
Input
Timing
Input
V
/2
CC
0 V
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
t
t
h
su
V
CC
Output
Control
(low-level
enabling)
Data
Input
V
CC
V
/2
V
CC
/2
CC
V
CC
/2
V
CC
/2
0 V
0 V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
t
t
PZL
PLZ
Output
Waveform 1
V
CC
V
CC
V
/2
CC
Input
V
CC
/2
V
CC
/2
S1 at 2 × V
(see Note B)
V
V
+ 0.15 V
V
CC
OL
0 V
OL
t
t
PZH
PHZ
t
t
PLH
PHL
Output
Waveform 2
S1 at GND
V
OH
V
V
OH
– 0.15 V
OH
V
/2
CC
Output
V
CC
/2
V
CC
/2
0 V
OL
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A.
C includes probe and jig capacitance.
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Z = 50 Ω, t ≤ 2 ns, t ≤ 2 ns.
O
r
f
D. The outputs are measured one at a time with one transition per measurement.
E.
F.
G.
t
t
t
and t
and t
and t
are the same as t
are the same as t
are the same as t
.
.
.
PLZ
PZL
PLH
PHZ
PZH
PHL
dis
en
pd
Figure 4. Load Circuit and Voltage Waveforms
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74AVC16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES156F – DECEMBER 1998 – REVISED FEBRUARY 2000
PARAMETER MEASUREMENT INFORMATION
V
= 3.3 V ± 0.3 V
CC
2 × V
CC
TEST
S1
S1
500 Ω
Open
From Output
Under Test
t
Open
pd
GND
t
/t
2 × V
CC
GND
PLZ PZL
/t
t
C
= 30 pF
PHZ PZH
L
500 Ω
(see Note A)
t
LOAD CIRCUIT
w
V
CC
V
CC
/2
V
CC
/2
Input
V
CC
Timing
Input
0 V
V
/2
CC
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
t
t
h
su
V
CC
Data
Input
Output
V
CC
V
CC
/2
V
CC
/2
Control
(low-level
enabling)
0 V
V
CC
/2
V
CC
/2
t
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
0 V
t
PZL
PLZ
Output
Waveform 1
V
CC
V
CC
V
CC
/2
Input
V
OL
+ 0.3 V
S1 at 2 × V
(see Note B)
V
CC
/2
V
CC
/2
CC
V
OL
0 V
t
t
PZH
PHZ
t
t
PLH
PHL
/2
Output
Waveform 2
S1 at GND
V
OH
V
V
OH
– 0.3 V
OH
V
CC
/2
V
Output
V
CC
/2
CC
0 V
(see Note B)
V
OL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A.
C includes probe and jig capacitance.
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Z = 50 Ω, t ≤ 2 ns, t ≤ 2 ns.
O
r
f
D. The outputs are measured one at a time with one transition per measurement.
E.
F.
G.
t
t
t
and t
and t
and t
are the same as t
are the same as t
are the same as t
.
dis
en
.
pd
PLZ
PZL
PLH
PHZ
PZH
PHL
.
Figure 5. Load Circuit and Voltage Waveforms
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
相关型号：
SN74AVC16374DGGE4
IC AVC SERIES, DUAL 8-BIT DRIVER, TRUE OUTPUT, PDSO48, PLASTIC, TSSOP-48, Bus Driver/Transceiver
TI
SN74AVC16501DGG
AVC SERIES, 18-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO56, PLASTIC, TSSOP-56
TI
SN74AVC16601DGGR
AVC SERIES, 18-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO56, PLASTIC, TSSOP-56
TI
©2020 ICPDF网 联系我们和版权申明