SN74CBT16861DGGR [TI]
20-BIT FET BUS SWITCH; 20位FET总线开关
| 型号： | SN74CBT16861DGGR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 20-BIT FET BUS SWITCH |
| 文件： | 总14页 (文件大小：281K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SN74CBT16861
20-BIT FET BUS SWITCH
SCDS068C – JULY 1998 – REVISED OCTOBER 2000
DGG, DGV, OR DL PACKAGE
(TOP VIEW)
Member of Texas Instruments’ Widebus
Family
5-Ω Switch Connection Between Two Ports
1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
NC
1A1
1A2
1A3
1A4
1A5
1A6
1A7
1A8
1A9
1A10
GND
NC
2A1
2A2
2A3
2A4
2A5
2A6
2A7
2A8
2A9
2A10
GND
V
CC
TTL-Compatible Input Levels
2
1OE
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
1B9
1B10
3
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
4
5
description
6
7
The SN74CBT16861 provides 20 bits of
high-speed TTL-compatible bus switching. The
low on-state resistance of the switch allows
connections to be made with minimal propagation
delay.
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
The device is organized as one dual 10-bit switch
with separate output-enable (OE) input. When OE
is low, the switch is on, and port A is connected to
port B. When OE is high, the switch is open, and
the high-impedance state exists between the two
ports.
V
CC
2OE
2B1
2B2
2B3
2B4
2B5
2B6
2B7
2B8
2B9
2B10
NC – No internal connection
ORDERING INFORMATION
ORDERABLE
TOP-SIDE
MARKING
†
PACKAGE
T
A
PART NUMBER
SN74CBT16861DL
SN74CBT16861DLR
SN74CBT16861DGGR
SN74CBT16861DGVR
Tube
SSOP – DL
CBT16861
Tape and reel
–40°C to 85°C
TSSOP – DGG Tape and reel
TVSOP – DGV Tape and reel
CBT16861
CY861
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.
FUNCTION TABLE
(each 10-bit bus switch)
INPUT
FUNCTION
OE
L
A port = B port
Disconnect
H
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74CBT16861
20-BIT FET BUS SWITCH
SCDS068C – JULY 1998 – REVISED OCTOBER 2000
logic diagram (positive logic)
2
46
37
1A1
1B1
11
1A10
1B10
47
14
1OE
2A1
34
25
2B1
23
35
2A10
2OE
2B10
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
CC
Input voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
I
Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA
Input clamp current, I (V < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
IK I/O
Package thermal impedance, θ (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W
JA
DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
MIN
4
MAX
UNIT
V
V
V
V
Supply voltage
5.5
CC
IH
IL
High-level control input voltage
Low-level control input voltage
Operating free-air temperature
2
V
0.8
85
V
T
A
–40
°C
NOTE 3: All unused control inputs of the device must be held at V
or GND to ensure proper device operation. Refer to the TI application report,
CC
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74CBT16861
20-BIT FET BUS SWITCH
SCDS068C – JULY 1998 – REVISED OCTOBER 2000
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
†
PARAMETER
TEST CONDITIONS
I = –18 mA
MIN TYP
MAX
–1.2
10
UNIT
V
IK
V
V
V
V
V
= 4.5 V,
= 0,
V
CC
CC
CC
CC
CC
I
V = 5.5 V
I
I
I
µA
= 5.5 V,
= 5.5 V,
= 5.5 V,
V = 5.5 V or GND
I
±1
I
I
O
= 0,
V = V
I
or GND
3
µA
mA
pF
CC
CC
‡
∆I
CC
Control inputs
One input at 3.4 V,
Other inputs at V
or GND
2.5
CC
C
C
Control inputs V = 3 V or 0
3
i
I
V
O
= 3 V or 0,
OE = V
5.5
pF
io(OFF)
CC
V
= 4 V,
CC
V = 2.4 V,
I
I = 15 mA
I
14
22
TYP at V
= 4 V
CC
§
r
on
I = 64 mA
I
5
5
7
7
Ω
V = 0
I
V
CC
= 4.5 V
I = 30 mA
I
V = 2.4 V,
I
I = 15 mA
I
10
15
†
‡
§
All typical values are at V
= 5 V (unless otherwise noted), T = 25°C.
A
CC
This is the increase in supply current for each input that is at the specified TTL voltage level rather than V
or GND.
CC
Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by
the lowest voltage of the two (A or B) terminals.
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figure 1)
V
= 5 V
CC
± 0.5 V
V
= 4 V
FROM
(INPUT)
TO
(OUTPUT)
CC
PARAMETER
UNIT
MIN
MAX
MIN
MAX
0.25
6.5
¶
t
t
t
A or B
OE
B or A
A or B
A or B
0.35
6.3
8
ns
ns
ns
pd
en
2.7
1.5
1.7
1.8
7.1
OE
dis
¶
Thepropagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when
driven by an ideal voltage source (zero output impedance).
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN74CBT16861
20-BIT FET BUS SWITCH
SCDS068C – JULY 1998 – REVISED OCTOBER 2000
PARAMETER MEASUREMENT INFORMATION
7 V
Open
GND
TEST
S1
S1
500 Ω
t
Open
7 V
From Output
Under Test
pd
t
/t
PLZ PZL
t
/t
Open
PHZ PZH
C
= 50 pF
L
500 Ω
(see Note A)
3 V
0 V
Output
Control
1.5 V
1.5 V
LOAD CIRCUIT
t
t
PLZ
PZL
Output
Waveform 1
S1 at 7 V
3.5 V
3 V
0 V
1.5 V
Input
1.5 V
1.5 V
V
+ 0.3 V
OL
V
(see Note B)
OL
OH
t
t
PHZ
PZH
t
t
PHL
PLH
Output
Waveform 2
S1 at Open
(see Note B)
V
V
OH
V
– 0.3 V
OH
1.5 V
Output
1.5 V
1.5 V
0 V
V
OL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A.
C includes probe and jig capacitance.
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Z = 50 Ω, t ≤ 2.5 ns, t ≤ 2.5 ns.
O
r
f
D. The outputs are measured one at a time with one transition per measurement.
E.
F.
G.
t
t
t
and t
and t
and t
are the same as t
are the same as t
are the same as t
.
dis
en
.
pd
PLZ
PZL
PLH
PHZ
PZH
PHL
.
Figure 1. Load Circuit and Voltage Waveforms
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
6-Aug-2007
PACKAGING INFORMATION
Orderable Device
74CBT16861DGGRE4
74CBT16861DGVRE4
74CBT16861DGVRG4
SN74CBT16861DGGR
SN74CBT16861DGVR
SN74CBT16861DL
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PREVIEW
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
TSSOP
DGG
48
48
48
48
48
48
48
48
48
56
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TVSOP
TVSOP
TSSOP
TVSOP
SSOP
DGV
DGV
DGG
DGV
DL
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SN74CBT16861DLG4
SN74CBT16861DLR
SN74CBT16861DLRG4
SN74CBT16861GQLR
SSOP
DL
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SSOP
DL
1000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SSOP
DL
1000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
BGA MI
CROSTA
R JUNI
OR
GQL
1000
TBD
Call TI
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
6-Aug-2007
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jul-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jul-2007
Device
Package Pins
Site
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) (mm) Quadrant
(mm)
330
(mm)
24
SN74CBT16861DGGR
SN74CBT16861DGVR
SN74CBT16861DLR
DGG
DGV
DL
48
48
48
MLA
MLA
MLA
8.6
6.8
15.8
10.1
16.2
1.8
1.6
3.1
12
12
16
24
24
32
Q1
Q1
Q1
330
24
330
32
11.35
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm) Width (mm) Height (mm)
SN74CBT16861DGGR
SN74CBT16861DGVR
SN74CBT16861DLR
DGG
DGV
DL
48
48
48
MLA
MLA
MLA
333.2
333.2
346.0
333.2
333.2
346.0
31.75
31.75
49.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jul-2007
Pack Materials-Page 3
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,23
0,13
M
0,07
0,40
24
13
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–ā8°
0,75
1
12
0,50
A
Seating Plane
0,08
0,15
0,05
1,20 MAX
PINS **
14
16
20
24
38
48
56
DIM
A MAX
A MIN
3,70
3,50
3,70
3,50
5,10
4,90
5,10
4,90
7,90
7,70
9,80
9,60
11,40
11,20
4073251/E 08/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001
DL (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0.025 (0,635)
48
0.0135 (0,343)
0.008 (0,203)
0.005 (0,13)
M
25
0.010 (0,25)
0.005 (0,13)
0.299 (7,59)
0.291 (7,39)
0.420 (10,67)
0.395 (10,03)
Gage Plane
0.010 (0,25)
0°–ā8°
1
24
0.040 (1,02)
0.020 (0,51)
A
Seating Plane
0.004 (0,10)
0.008 (0,20) MIN
PINS **
0.110 (2,79) MAX
28
48
0.630
56
DIM
0.380
(9,65)
0.730
A MAX
A MIN
(16,00) (18,54)
0.370
(9,40)
0.620
0.720
(15,75) (18,29)
4040048/E 12/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO-118
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
M
0,08
0,50
48
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
0,25
1
24
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
48
56
64
DIM
A MAX
12,60
12,40
14,10
13,90
17,10
16,90
A MIN
4040078/F 12/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lpw
Telephony
Low Power
Wireless
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明