SN74HCS139-Q1 [TI]
SN74HCS139-Q1 Automotive Qualified Dual 2- to 4-Line Decoders/Demultiplexers with Schmitt-Trigger Inputs;
| 型号： | SN74HCS139-Q1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | SN74HCS139-Q1 Automotive Qualified Dual 2- to 4-Line Decoders/Demultiplexers with Schmitt-Trigger Inputs |
| 文件： | 总23页 (文件大小：1336K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
SN74HCS139-Q1 Automotive Qualified Dual 2- to 4-Line Decoders/Demultiplexers
with Schmitt-Trigger Inputs
1 Features
3 Description
•
AEC-Q100 Qualified for automotive applications:
– Device temperature grade 1: –40°C to +125°C,
TA
– Device HBM ESD Classification Level 2
– Device CDM ESD Classifcation Level C6
Wide operating voltage range: 2 V to 6 V
Schmitt-trigger inputs allow for slow or noisy input
signals
Low power consumption
– Typical ICC of 100 nA
– Typical input leakage current of ±100 nA
±7.8-mA output drive at 6 V
The SN74HCS139-Q1 contains two two-to-four
decoders with one active low output strobe (G). When
the outputs of one channel are gated by the strobe
input, they are all forced into the high state. When the
outputs are not disabled by the strobe input, only the
selected output is low while all others are high.
•
•
Device Information
PART NUMBER
SN74HCS139PW-Q1
SN74HCS139D-Q1
PACKAGE(1)
TSSOP (16)
SOIC (16)
BODY SIZE (NOM)
5.00 mm × 4.40 mm
9.90 mm × 3.90 mm
•
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
•
2 Applications
•
•
Memory device selection with shared data bus
Reduce required number of outputs for chip select
applications
•
Route data
Supports Slow Inputs
Low Power
Noise Rejection
Input Voltage
Waveforms
Time
Input Voltage
Time
Standard
CMOS Input
Response
Waveforms
Time
Time
Input Voltage
Schmitt-trigger
CMOS Input
Response
Waveforms
Time
Time
Input Voltage
Benefits of Schmitt-trigger inputs
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings ....................................... 4
6.2 ESD Ratings .............................................................. 4
6.3 Recommended Operating Conditions ........................4
6.4 Thermal Information ...................................................4
6.5 Electrical Characteristics ............................................5
6.6 Switching Characteristics ...........................................5
6.7 Operating Characteristics .......................................... 5
6.8 Typical Characteristics................................................6
7 Parameter Measurement Information............................7
8 Detailed Description........................................................8
8.1 Functional Block Diagram...........................................8
8.2 Feature Description.....................................................8
8.3 Device Functional Modes............................................9
9 Application and Implementation..................................10
9.1 Application Information............................................. 10
9.2 Typical Application.................................................... 10
10 Power Supply Recommendations..............................13
11 Layout...........................................................................13
11.1 Layout Guidelines................................................... 13
11.2 Layout Example...................................................... 13
12 Device and Documentation Support..........................14
12.1 Documentation Support.......................................... 14
12.2 Receiving Notification of Documentation Updates..14
12.3 Support Resources................................................. 14
12.4 Trademarks.............................................................14
12.5 Electrostatic Discharge Caution..............................14
12.6 Glossary..................................................................14
13 Mechanical, Packaging, and Orderable
Information.................................................................... 15
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
DATE
REVISION
NOTES
September 2020
*
Initial Release
Copyright © 2020 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
5 Pin Configuration and Functions
1G
1A0
1A1
1Y0
1Y1
1Y2
1Y3
GND
VCC
2G
1
2
3
4
5
6
16
15
14
2A0
2A1
2Y0
13
12
11
10
9
2Y1
2Y2
2Y3
7
8
D or PW Package 16-Pin SOIC or TSSOP Top View
Table 5-1. Pin Functions
PIN
I/O
DESCRIPTION
SOIC or TSSOP
NO.
NAME
1
1G
1A0
1A1
1Y0
1Y1
1Y2
1Y3
GND
2Y3
2Y2
2Y1
2Y0
2A1
2A0
2G0
VCC
I
I
Channel 1, output enable, active low
2
Channel 1, address select 0
Channel 1, address select 1
Channel 1, output 0
3
I
4
O
O
O
O
—
O
O
O
O
I
5
Channel 1, output 1
6
Channel 1, output 2
7
Channel 1, output 3
8
Ground
9
Channel 2, output 3
10
11
12
13
14
15
16
Channel 2, output 2
Channel 2, output 1
Channel 2, output 0
Channel 2, address select 1
Channel 2, address select 0
Channel 2, output enable, active low
Positive supply
I
I
—
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
7
UNIT
V
VCC
IIK
Supply voltage
–0.5
Input clamp current(2)
VI < –0.5 V or VI > VCC + 0.5 V
VI < –0.5 V or VI > VCC + 0.5 V
VO = 0 to VCC
±20
±20
±35
±70
150
150
mA
mA
mA
mA
°C
IOK
IO
Output clamp current(2)
Continuous output current
Continuous current through VCC or GND
Junction temperature(3)
Storage temperature
TJ
Tstg
–65
°C
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
(3) Guaranteed by design.
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per AEC Q100-002(1)
HBM ESD Classification Level 2
±4000
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per AEC
Q100-011 CDM ESD Classification Level C6
±1500
(1) AEC Q100-002 indicate that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2
NOM
MAX
6
UNIT
V
VCC
VI
Supply voltage
Input voltage
5
0
VCC
VCC
125
V
VO
TA
Output voltage
Ambient temperature
0
V
–40
°C
6.4 Thermal Information
SN74HCS139-Q1
THERMAL METRIC(1)
PW (TSSOP)
16 PINS
141.2
78.8
D (SOIC)
16 PINS
122.2
80.9
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
85.8
80.6
ΨJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
27.7
40.4
ΨJB
85.5
80.3
RθJC(bot)
N/A
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2020 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
6.5 Electrical Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
VCC
MIN
0.7
1.7
2.1
0.3
0.9
1.2
0.2
0.4
0.6
TYP
MAX UNIT
2 V
1.5
VT+
Positive switching threshold
4.5 V
6 V
3.15
4.2
1.0
2.2
3.0
1.0
1.4
1.6
V
V
V
V
V
2 V
VT-
Negative switching threshold
Hysteresis (VT+ - VT-)(1)
High-level output voltage
Low-level output voltage
4.5 V
6 V
2 V
ΔVT
VOH
VOL
4.5 V
6 V
IOH = -20 µA
VI = VIH or VIL IOH = -6 mA
IOH = -7.8 mA
2 V to 6 V
4.5 V
6 V
VCC – 0.1 VCC – 0.002
4.0
5.4
4.3
5.75
0.002
0.18
0.22
±100
0.1
IOL = 20 µA
2 V to 6 V
4.5 V
6 V
0.1
0.30
0.33
VI = VIH or VIL IOL = 6 mA
IOL = 7.8 mA
II
Input leakage current
Supply current
VI = VCC or 0
6 V
±1000 nA
ICC
Ci
VI = VCC or 0, IO = 0
6 V
2
5
µA
pF
Input capacitance
2 V to 6 V
(1) Guaranteed by design.
6.6 Switching Characteristics
CL = 50 pF; over operating free-air temperature range (unless otherwise noted). See Parameter Measurement
Information.
Operating free-air temperature (TA)
PARAMETER
Propagation delay
Transition-time
FROM
TO
VCC
25°C
TYP
–40°C to 125°C
MIN TYP MAX
UNIT
MIN
MAX
30
11
10
28
11
9
2 V
19
7
45
18
14
45
18
15
17
8
A or B
Any Y
4.5 V
6 V
6
tpd
ns
2 V
18
7
G
Any Y
4.5 V
6 V
6
2 V
9
tt
Any output 4.5 V
6 V
5
ns
4
7
6.7 Operating Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX UNIT
Power dissipation capacitance
per gate
Cpd
No load
2 V to 6 V
40
pF
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
6.8 Typical Characteristics
TA = 25°C
46
44
42
40
38
36
34
32
30
28
26
70
65
60
55
50
45
40
35
30
VCC = 2 V
VCC = 3.3 V
VCC = 4.5 V
VCC = 6 V
VCC = 2 V
VCC = 3.3 V
VCC = 4.5 V
VCC = 6 V
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
Output Sink Current (mA)
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
Output Source Current (mA)
Figure 6-1. Output driver resistance in LOW state. Figure 6-2. Output driver resistance in HIGH state.
0.2
0.18
0.16
0.14
0.12
0.1
0.65
0.6
VCC = 2 V
VCC = 4.5 V
VCC = 5 V
VCC = 6 V
0.55
0.5
VCC = 2.5 V
VCC = 3.3 V
0.45
0.4
0.35
0.3
0.08
0.06
0.04
0.02
0
0.25
0.2
0.15
0.1
0.05
0
0
0.5
1
1.5
2
2.5
3
3.5
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
VI œ Input Voltage (V)
VI œ Input Voltage (V)
Figure 6-3. Supply current across input voltage, 2-,
2.5-, and 3.3-V supply
Figure 6-4. Supply current across input voltage,
4.5-, 5-, and 6-V supply
Copyright © 2020 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
7 Parameter Measurement Information
Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators
having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tt < 2.5 ns.
For clock inputs, fmax is measured when the input duty cycle is 50%.
The outputs are measured one at a time with one input transition per measurement.
Test
Point
VCC
0 V
VOH
VOL
VOH
VOL
Input
Output
Output
50%
50%
From Output
Under Test
(1)
(1)
tPLH
tPHL
(1)
CL
50%
50%
(1) CL includes probe and test-fixture capacitance.
(1)
(1)
tPHL
tPLH
Figure 7-1. Load Circuit for Push-Pull Outputs
50%
50%
(1) The greater between tPLH and tPHL is the same as tpd
.
Figure 7-2. Voltage Waveforms Propagation Delays
VCC
90%
Input
90%
10%
0 V
10%
tr(1)
tf(1)
VOH
90%
10%
90%
Output
10%
VOL
tr(1)
tf(1)
(1) The greater between tr and tf is the same as tt.
Figure 7-3. Voltage Waveforms, Input and Output Transition Times
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
8 Detailed Description
8.1 Functional Block Diagram
One of Two 2:4 Decoders
DECODER
00
OUTPUT
ENABLE
xY0
xY1
xY2
xY3
xA0
xA1
xG
01
10
11
Figure 8-1. Logic Diagram (Positive Logic) for SN74HCS139-Q1 -Q1
8.2 Feature Description
8.2.1 Balanced CMOS Push-Pull Outputs
This device includes balanced CMOS push-pull outputs. The term "balanced" indicates that the device can sink
and source similar currents. The drive capability of this device may create fast edges into light loads so routing
and load conditions should be considered to prevent ringing. Additionally, the outputs of this device are capable
of driving larger currents than the device can sustain without being damaged. It is important for the output power
of the device to be limited to avoid damage due to overcurrent. The electrical and thermal limits defined in the
Absolute Maximum Ratings must be followed at all times.
Unused push-pull CMOS outputs should be left disconnected.
8.2.2 CMOS Schmitt-Trigger Inputs
This device includes inputs with the Schmitt-trigger architecture. These inputs are high impedance and are
typically modeled as a resistor in parallel with the input capacitance given in the Electrical Characteristics table
from the input to ground. The worst case resistance is calculated with the maximum input voltage, given in the
Absolute Maximum Ratings table, and the maximum input leakage current, given in the Electrical Characteristics
table, using Ohm's law (R = V ÷ I).
The Schmitt-trigger input architecture provides hysteresis as defined by ΔVT in the Electrical Characteristics
table, which makes this device extremely tolerant to slow or noisy inputs. While the inputs can be driven much
slower than standard CMOS inputs, it is still recommended to properly terminate unused inputs. Driving the
inputs with slow transitioning signals will increase dynamic current consumption of the device. For additional
information regarding Schmitt-trigger inputs, please see Understanding Schmitt Triggers.
8.2.3 Clamp Diode Structure
The inputs and outputs to this device have both positive and negative clamping diodes as depicted in Electrical
Placement of Clamping Diodes for Each Input and Output.
CAUTION
Voltages beyond the values specified in the Absolute Maximum Ratings table can cause damage to
the device. The input and output voltage ratings may be exceeded if the input and output clamp-
current ratings are observed.
Copyright © 2020 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
VCC
Logic
GND
Device
+IIK
+IOK
Input
Output
-IIK
-IOK
Figure 8-2. Electrical Placement of Clamping Diodes for Each Input and Output
8.3 Device Functional Modes
Function Table lists the functional modes of the SN74HCS139-Q1.
Table 8-1. Function Table
INPUTS(1)
OUTPUTS
nG
nA1
nA0
nY0
L
nY1
nY2
nY3
L
L
L
L
H
L
H
L
H
H
L
H
H
H
L
L
H
L
H
H
X
H
H
H
H
L
H
X
H
H
H
H
H
H
(1) H = High Voltage Level, L = Low Voltage Level, X = Don't Care
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
9 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
9.1 Application Information
The SN74HCS139-Q1 is used to control multiple devices that operate on a shared data bus. A decoder provides
the capability to have a binary encoded input activate only one of the device's outputs. This is ideal for solid state
memory applications where multiple devices have to be read or written to with a limited number of GPIO pins
used on the system controller. The decoder is used to activate the chip select (CS) input to the selected memory
device, and the controller can then read or write from that device alone when using a shared bus.
9.2 Typical Application
1Y0
Device A1
1A0
1A1
1Y1
1Y2
1Y3
Device A2
Device A3
Device A4
1G
2G
System
Controller
2Y0
2Y1
2Y2
2Y3
Device B1
Device B2
Device B3
Device B4
2A0
2A1
Data Bus
Figure 9-1. Typical application block diagram
9.2.1 Design Requirements
9.2.1.1 Power Considerations
Ensure the desired supply voltage is within the range specified in the Recommended Operating Conditions. The
supply voltage sets the device's electrical characteristics as described in the Electrical Characteristics.
The positive voltage supply must be capable of sourcing current equal to the total current to be sourced by all
outputs of the SN74HCS139-Q1 plus the maximum static supply current, ICC, listed in Electrical Characteristics
and any transient current required for switching. The logic device can only source as much current as is provided
by the positive supply source. Be sure not to exceed the maximum total current through VCC listed in the
Absolute Maximum Ratings.
The ground must be capable of sinking current equal to the total current to be sunk by all outputs of the
SN74HCS139-Q1 plus the maximum supply current, ICC, listed in Electrical Characteristics, and any transient
current required for switching. The logic device can only sink as much current as can be sunk into its ground
connection. Be sure not to exceed the maximum total current through GND listed in the Absolute Maximum
Ratings.
The SN74HCS139-Q1 can drive a load with a total capacitance less than or equal to xx pF while still meeting all
of the datasheet specifications. Larger capacitive loads can be applied, however it is not recommended to
exceed xx pF.
The SN74HCS139-Q1 can drive a load with total resistance described by RL ≥ VO / IO, with the output voltage
and current defined in the Electrical Characteristics table with VOH and VOL. When outputting in the high state,
Copyright © 2020 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
the output voltage in the equation is defined as the difference between the measured output voltage and the
supply voltage at the VCC pin.
Total power consumption can be calculated using the information provided in CMOS Power Consumption and
Cpd Calculation.
Thermal increase can be calculated using the information provided in Thermal Characteristics of Standard Linear
and Logic (SLL) Packages and Devices.
CAUTION
The maximum junction temperature, TJ(max) listed in the Absolute Maximum Ratings, is an additional
limitation to prevent damage to the device. Do not violate any values listed in the Absolute Maximum
Ratings. These limits are provided to prevent damage to the device.
9.2.1.2 Input Considerations
Input signals must cross Vt-(min) to be considered a logic LOW, and Vt+(max) to be considered a logic HIGH. Do
not exceed the maximum input voltage range found in the Absolute Maximum Ratings.
Unused inputs must be terminated to either VCC or ground. These can be directly terminated if the input is
completely unused, or they can be connected with a pull-up or pull-down resistor if the input is to be used
sometimes, but not always. A pull-up resistor is used for a default state of HIGH, and a pull-down resistor is used
for a default state of LOW. The resistor size is limited by drive current of the controller, leakage current into the
SN74HCS139-Q1, as specified in the Electrical Characteristics, and the desired input transition rate. A 10-kΩ
resistor value is often used due to these factors.
The SN74HCS139-Q1 has no input signal transition rate requirements because it has Schmitt-trigger inputs.
Another benefit to having Schmitt-trigger inputs is the ability to reject noise. Noise with a large enough amplitude
can still cause issues. To know how much noise is too much, please refer to the ΔVT(min) in the Electrical
Characteristics. This hysteresis value will provide the peak-to-peak limit.
Unlike what happens with standard CMOS inputs, Schmitt-trigger inputs can be held at any valid value without
causing huge increases in power consumption. The typical additional current caused by holding an input at a
value other than VCC or ground is plotted in the Typical Characteristics.
Refer to the Feature Description section for additional information regarding the inputs for this device.
9.2.1.3 Output Considerations
The positive supply voltage is used to produce the output HIGH voltage. Drawing current from the output will
decrease the output voltage as specified by the VOH specification in the Electrical Characteristics. The ground
voltage is used to produce the output LOW voltage. Sinking current into the output will increase the output
voltage as specified by the VOL specification in the Electrical Characteristics.
Push-pull outputs that could be in opposite states, even for a very short time period, should never be connected
directly together. This can cause excessive current and damage to the device.
Two channels within the same device with the same input signals can be connected in parallel for additional
output drive strength.
Unused outputs can be left floating. Do not connect outputs directly to VCC or ground.
Refer to Feature Description section for additional information regarding the outputs for this device.
9.2.2 Detailed Design Procedure
1. Add a decoupling capacitor from VCC to GND. The capacitor needs to be placed physically close to the
device and electrically close to both the VCC and GND pins. An example layout is shown in the Layout
section.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
2. Ensure the capacitive load at the output is ≤ xx pF. This is not a hard limit, however it will ensure optimal
performance. This can be accomplished by providing short, appropriately sized traces from the
SN74HCS139-Q1 to the receiving device(s).
3. Ensure the resistive load at the output is larger than (VCC / IO(max)) Ω. This will ensure that the maximum
output current from the Absolute Maximum Ratings is not violated. Most CMOS inputs have a resistive load
measured in megaohms; much larger than the minimum calculated above.
4. Thermal issues are rarely a concern for logic gates, however the power consumption and thermal increase
can be calculated using the steps provided in the application report, CMOS Power Consumption and Cpd
Calculation.
9.2.3 Application Curve
1G
1A1
1A0
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
Figure 9-2. Application timing diagram
Copyright © 2020 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
10 Power Supply Recommendations
The power supply can be any voltage between the minimum and maximum supply voltage rating located in the
Recommended Operating Conditions. Each VCC terminal should have a good bypass capacitor to prevent power
disturbance. A 0.1-μF capacitor is recommended for this device. It is acceptable to parallel multiple bypass caps
to reject different frequencies of noise. The 0.1-μF and 1-μF capacitors are commonly used in parallel. The
bypass capacitor should be installed as close to the power terminal as possible for best results, as shown in
given example layout image.
11 Layout
11.1 Layout Guidelines
When using multiple-input and multiple-channel logic devices inputs must not ever be left floating. In many
cases, functions or parts of functions of digital logic devices are unused; for example, when only two inputs of a
triple-input AND gate are used or only 3 of the 4 buffer gates are used. Such unused input pins must not be left
unconnected because the undefined voltages at the outside connections result in undefined operational states.
All unused inputs of digital logic devices must be connected to a logic high or logic low voltage, as defined by the
input voltage specifications, to prevent them from floating. The logic level that must be applied to any particular
unused input depends on the function of the device. Generally, the inputs are tied to GND or VCC, whichever
makes more sense for the logic function or is more convenient.
11.2 Layout Example
GND VCC
Recommend GND flood fill for
improved signal isolation, noise
reduction, and thermal dissipation
Bypass capacitor
placed close to the
device
0.1 ꢀF
16
Unused input
tied to GND
Unused
inputs tied to
VCC
1G
1A0
1A1
1Y0
1Y1
1Y2
1Y3
GND
VCC
1
2
3
4
5
6
7
8
15
14
13
12
11
10
9
2G
2A0
2A1
2Y0
2Y1
2Y2
2Y3
Avoid 90°
corners for
signal lines
Unused
output left
floating
Figure 11-1. Example layout for the SN74HCS139-Q1.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
12 Device and Documentation Support
TI offers an extensive line of development tools. Tools and software to evaluate the performance of the device,
generate code, and develop solutions are listed below.
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
•
•
•
Texas Instruments, HCMOS Design Considerations application report (SCLA007)
Texas Instruments, CMOS Power Consumption and Cpd Calculation application report (SDYA009)
Texas Instruments, Designing With Logic application report
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
12.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
12.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2020 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: SN74HCS139-Q1
SN74HCS139-Q1
SCLS812 – SEPTEMBER 2020
www.ti.com
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: SN74HCS139-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Nov-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
2500
2000
(1)
(2)
(3)
(4/5)
(6)
SN74HCS139QDRQ1
SN74HCS139QPWRQ1
PREVIEW
SOIC
D
16
16
Green (RoHS
& no Sb/Br)
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
HCS139Q
HCS139Q
ACTIVE
TSSOP
PW
Green (RoHS
& no Sb/Br)
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Nov-2020
OTHER QUALIFIED VERSIONS OF SN74HCS139-Q1 :
Catalog: SN74HCS139
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Oct-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
SN74HCS139QPWRQ1 TSSOP
PW
16
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Oct-2020
*All dimensions are nominal
Device
Package Type Package Drawing Pins
TSSOP PW 16
SPQ
Length (mm) Width (mm) Height (mm)
853.0 449.0 35.0
SN74HCS139QPWRQ1
2000
Pack Materials-Page 2
PACKAGE OUTLINE
PW0016A
TSSOP - 1.2 mm max height
S
C
A
L
E
2
.
5
0
0
SMALL OUTLINE PACKAGE
SEATING
PLANE
C
6.6
6.2
TYP
A
0.1 C
PIN 1 INDEX AREA
14X 0.65
16
1
2X
5.1
4.9
4.55
NOTE 3
8
9
0.30
16X
4.5
4.3
NOTE 4
1.2 MAX
0.19
B
0.1
C A B
(0.15) TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.75
0.50
A
20
0 -8
DETAIL A
TYPICAL
4220204/A 02/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-153.
www.ti.com
EXAMPLE BOARD LAYOUT
PW0016A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
SYMM
16X (1.5)
(R0.05) TYP
16
1
16X (0.45)
SYMM
14X (0.65)
8
9
(5.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 10X
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
15.000
(PREFERRED)
SOLDER MASK DETAILS
4220204/A 02/2017
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
PW0016A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
16X (1.5)
SYMM
(R0.05) TYP
16
1
16X (0.45)
SYMM
14X (0.65)
8
9
(5.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 10X
4220204/A 02/2017
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号：
UL1042
UL1042 - Uk砤d zr體nowa縪nego mieszacza iloczynowegoWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV201
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14
IC-SM-VIDEO AMPWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TA
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TC
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV302N16
IC-SM-4:1 MUX SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV4089
VIDEO AMPLIFIER WITH DC RESTORATIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
©2020 ICPDF网 联系我们和版权申明