TCA39306-Q1 [TI]
TCA39306 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator;型号: | TCA39306-Q1 |
厂家: | TEXAS INSTRUMENTS |
描述: | TCA39306 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator |
文件: | 总29页 (文件大小:1831K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
TCA39306 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator
1 Features
2 Applications
•
2-Bit bidirectional translator for SDA and SCL lines
in mixed-mode I2C applications
•
I2C, SMBus, PMBus, MDIO, UART, low-speed
SDIO, GPIO, and other two-signal interfaces
Servers
Routers (telecom switching equipment)
Personal computers
•
Standard-mode, fast-mode, and fast-mode plus
•
•
•
•
I2C and SMBus compatible
•
•
I3C compatible (12.5 MHz supported)
Allows voltage-level translation between
– 0.9-V VREF1 and 1.8-V, 2.5-V, 3.3-V,
or 5-V VREF2
Industrial automation
3 Description
The TCA39306 is a dual bidirectional voltage-level
translator compatible with I2C, SMBus, and I3C with
an enable (EN) input, and is operational from 0.9-V to
– 1.2-V VREF1 and 1.8-V, 2.5-V, 3.3-V,
or 5-V VREF2
– 1.8-V VREF1 and 2.5-V, 3.3-V, or 5-V VREF2
– 2.5-V VREF1 and 3.3-V or 5-V VREF2
– 3.3-V VREF1 and 5-V VREF2
3.3-V VREF1 and 1.8-V to 5.5-V VREF2
.
The device allows bidirectional voltage translations
between 0.85 V and 5 V, without the use of a
•
•
•
•
•
Provides bidirectional voltage translation with no
direction Pin
direction pin. The low ON-state resistance (RON
)
Low ON-state resistance between input and output
ports provides less signal distortion
Open-drain I2C I/O ports (SCL1, SDA1, SCL2, and
SDA2)
of the switch allows connections to be made with
minimal propagation delay. When EN is high, the
translator switch is ON, and the SCL1 and SDA1
I/O are connected to the SCL2 and SDA2 I/O,
respectively, allowing bidirectional data flow between
ports. When EN is low, the translator switch is off, and
a high-impedance state exists between ports.
5-V Tolerant I2C I/O ports to support mixed-mode
signal operation
High-impedance SCL1, SDA1, SCL2, and SDA2
pins for EN = Low
In addition to voltage translation, the TCA39306 can
be used to isolate a higher speed bus from a lower
speed bus by controlling the EN pin to disconnect the
slower bus during fast-mode communication.
•
•
Lockup-free operation for isolation when EN = Low
Flow-through pinout for ease of printed-circuit-
board trace routing
ESD Protection Exceeds JESD 22
– 2000-V human-body model (A114-A)
– 1000-V charged-device model (C101)
•
Device Information
PART NUMBER
PACKAGE(1)
VSSOP (8)
SOT-23 (8)(2)
X2SON (8)
BODY SIZE (NOM)
2.30 mm x 2.00 mm
2.90 mm x 1.60 mm
1.35 mm x 0.80 mm
TCA39306
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
(2) Product Preview
200 kꢀ
VREF1
VREF2
EN
I2C, SMBus, or
I3C controller
TCA39306
Responder
devices
SCL1
SDA1
SCL2
SDA2
GND
Simplified Application Diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings ....................................... 4
6.2 ESD Ratings .............................................................. 4
6.3 Recommended Operating Conditions ........................4
6.4 Thermal Information ...................................................5
6.5 Electrical Characteristics ............................................5
6.6 Switching Characteristics ...........................................6
6.7 Typical Characteristics................................................8
7 Parameter Measurement Information............................9
8 Detailed Description......................................................11
8.1 Overview................................................................... 11
8.2 Functional Block Diagram.........................................16
8.3 Feature Description...................................................16
8.4 Device Functional Modes..........................................16
9 Application and Implementation..................................17
9.1 Application Information............................................. 17
9.2 Typical Application.................................................... 17
9.3 Systems Examples: I3C Usage Considerations....... 20
10 Power Supply Recommendations..............................22
11 Layout...........................................................................23
11.1 Layout Guidelines................................................... 23
11.2 Layout Example...................................................... 23
12 Device and Documentation Support..........................24
12.1 Receiving Notification of Documentation Updates..24
12.2 Support Resources................................................. 24
12.3 Trademarks.............................................................24
12.4 Electrostatic Discharge Caution..............................24
12.5 Glossary..................................................................24
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision * (June 2021) to Revision A (August 2021)
Page
•
Changed the document from Advanced Information to Production data............................................................1
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
5 Pin Configuration and Functions
GND
1
2
3
4
8
7
6
5
EN
V
GND
1
2
3
4
8
7
6
5
EN
V
V
ꢀ
REF1
SCL1
REF2
V
ꢀ
REF1
SCL1
REF2
SCL2
SDA2
SCL2
SDA2
SDA1
SDA1
Figure 5-2. DCU Package, 8-Pin VSSOP, Top View
Figure 5-1. DDF Package, 8-Pin SOT, Top View
GND
VREF1
SCL1
1
7
6
5
VREF2
8
EN
2
SCL2
4
SDA1
3
SDA2
Not to scale
Figure 5-3. DTM Package, 8-Pin X2SON, Top View
Table 5-1. Pin Functions
PIN
NO.
I/O
DESCRIPTION
NAME
EN
DCU, DDF
DTM
8
1
3
6
4
5
2
7
8
1
3
6
4
5
2
7
I
Switch enable input
GND
—
I/O
I/O
I/O
I/O
I
Ground, 0 V
SCL1
SCL2
SDA1
SDA2
VREF1
VREF2
Serial clock, low-voltage side
Serial clock, high-voltage side
Serial data, low-voltage side
Serial data, high-voltage side
Low-voltage-side reference supply voltage for SCL1 and SDA1
High-voltage-side reference supply voltage for SCL2 and SDA2
I
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
–0.5
–0.5
–0.5
–0.5
MAX
7
UNIT
V
VREF1
VREF2
VI
DC reference voltage range
DC reference bias voltage range
Input voltage range (2)
7
V
7
V
VI/O
Input-output voltage range (2)
Continuous channel current
Input Clamp Current (VI < 0 )
Junction temperature
7
V
128
–50
150
150
mA
mA
°C
°C
IIK
TJ(Max)
Tstg
Storage temperature
–65
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions.
If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully
functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.
(2) The input and input-output negative voltage ratings may be exceeded if the input and output current ratings are observed.
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/ESDA/
JEDEC JS-001(1)
±2000
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per ANSI/ESDA/
JEDEC JS-002 (2)
±1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
SCL1, SDA1, SCL2,
SDA2
VI/O
Input-output voltage
0
5.5
V
(1)
(1)
VREF1
VREF2
EN-
Reference Voltage
Reference Voltage
0
0
5.5
5.5
V
V
Switch mode enable voltage (Switch mode enable voltage)
1.5
0
5.5
V
Switch(2)
EN
Enable input voltage
Pass switch current
Ambient temperature
5.5
64
V
IPASS
TA
mA
°C
–40
125
(1) To support translation, VREF1 supports 0.85 V to VREF2 - 0.6 V. VREF2 must be between VREF1 + 0.6 V to 5.5 V. See Typical
Application for more information.
(2) To support switching, VREF1 and VREF2 Do not need to be connected. EN pin should use a voltage not less than 1.5V when the switch
mode is to be enabled. Enabled voltage on this pin should be equal to 1.5V or I/O supply voltage, whichever is higher.
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
6.4 Thermal Information
TCA39306
THERMAL METRIC(1)
DCU
8 PINS
275.5
127.1
186.9
65.7
DTM
8 PINS
289.5
185.5
193.8
27.4
UNIT
RθJA
RθJC(top)
RθJB
ΨJT
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
ΨJB
185.9
193.2
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
TYP
PARAMETER
Input clamp voltage
TEST CONDITIONS
EN = 0 V
MIN
MAX UNIT
(1)
VIK
IIH
II = -18 mA
-1.2
0
5
V
VI = 5 V, VO
= 0V
Input leakage current
Threshold voltage
Input capacitance
Off capacitance
EN = 0 V
µA
VI = 0.1 V, VO = 0 V, Find
VEN where IO = 500 µA
VT
IO = 500 µA
0.7
11
4
1.0
V
VI = 3 V or 0
V
CI(EN)
CIO(off)
CIO(on)
pF
pF
VO = 3 V or 0
V
SCLn, SDAn
SCLn, SDAn
EN = 0 V
EN = 3 V
6
VO = 3 V or 0
V
On capacitance
10.5 12.5 pF
VI = 0 V(3)
VI = 0 V(3)
VI = 0 V(3)
VI = 0 V(3)
IO = 64 mA
IO = 64 mA
IO = 64 mA
IO = 15 mA
EN = 4.5 V
EN = 3 V
3.5
4.7
6.3
25.5
6
5.5
7
Ω
Ω
Ω
Ω
Ω
Ω
Ω
EN = 2.3 V
EN = 1.5 V
EN = 4.5 V
EN = 3 V
9.5
32
15
75
75
SCLn, SDAn (-40 to
125C)
(2)
RON
On-state resistance
VI = 2.4 V(4) IO = 15 mA
VI = 2.4 V(4) IO = 15 mA
VI = 1.7 V(4) IO = 15 mA
1
20
20
50
EN = 2.3 V
55
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
6.5 Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
TYP
PARAMETER
TEST CONDITIONS
VCC1 = 1 V
MIN
MAX UNIT
(1)
5
4
25
10
VCC1 = 1.8
V
IO = 64 mA
Ω
8
VCC1 = 2.5
V
3
VCC1 = 3.3
V
3
5
4
7
10
9
VI = 0 V,
VCC2 = 5
V(5)
VCC1 = 1 V
VCC1 = 1.8
V
IO = 32 mA
Ω
8
VCC1 = 2.5
V
3
3
RON
On-state resistance
SCLn, SDAn
VCC1 = 3.3
V
7
VI = 1.8 V,
VCC2 = 5
V(5)
VCC1 = 3.3
V
IO = 15 mA
4
7
5
6
13
24
18
19
Ω
Ω
Ω
Ω
VI = 1 V,
VCC1 = 1.8
V
VCC2 = 3.3 IO = 10 mA
V(5)
VI = 0 V,
VCC2 = 3.3 IO = 10 mA
VCC1 = 1 V
VCC1 = 1 V
V(5)
VI = 0 V,
VCC2 = 1.8 IO = 10 mA
V(5)
(1) All typical values are at TA = 25°C.
(2) Measured by the voltage drop between the SCL1 and SCL2, or SDA1 and SDA2 terminals, at the indicated current through the switch.
Minimum ON-state resistance is determined by the lowest voltage of the two terminals.
(3) Measured in current source configuration only. See Figure 7-1
(4) Measured in current sink configuration only. See Figure 7-1
(5) Measured in application connected current source configuration only. See Figure 7-2
6.6 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
13
ns
32
VCC1 = 0.85 V, VCC2 = 1.98 V,
RL_Input = 1.35 kΩ
15
ns
45
VCC1 = 0.85 V, VCC2 = 3.6 V, RL_Input
= 1.35 kΩ
20
ns
46
VCC1 = 0.85 V, VCC2 = 5.5 V, RL_Input
= 1.35 kΩ
TPLH
Low-to-high propagation delay(1)
8
ns
20
VCC1 = 1.65 V, VCC2 = 3.6 V, RL_Input
= 1.35 kΩ
15
ns
35
VCC1 = 1.65 V, VCC2 = 5.5 V, RL_Input
= 1.35 kΩ
2
VCC1 = 3 V, VCC2 = 5.5 V, RL_Input
1.35 kΩ
=
ns
5
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
6.6 Switching Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
CL = 15 pF
CL = 50 pF
3
VCC1 = 0.85 V, VCC2 = 1.98 V,
RL_Input = 1.35 kΩ
ns
4
3
VCC1 = 0.85 V, VCC2 = 3.6 V, RL_Input
= 1.35 kΩ
ns
5
3
VCC1 = 0.85 V, VCC2 = 5.5 V, RL_Input
= 1.35 kΩ
ns
5
TPHL
High-to-low propagation delay(1)
2
VCC1 = 1.65 V, VCC2 = 3.6 V, RL_Input
= 1.35 kΩ
ns
3
3
VCC1 = 1.65 V, VCC2 = 5.5 V, RL_Input
= 1.35 kΩ
ns
3
1.5
ns
2
VCC1 = 3 V, VCC2 = 5.5 V, RL_Input
1.35 kΩ
=
(1) Measured with an application propagation delay setup. See Figure 7-3
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
6.7 Typical Characteristics
300
110
100
90
80
70
60
50
40
30
20
10
0
125C
125C
85C
25C
-40C
270
85C
25C
-40C
240
210
180
150
120
90
60
30
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
VSDA1 or VSCL1 (V)
VSDA1 or VSCL1 (V)
VEN = 1.5 V
II = 15 mA
VEN = 4.5 V
II = 15 mA
Figure 6-1. On-Resistance (RON) vs Input Voltage
Figure 6-2. On-Resistance (RON) vs Input Voltage
(VSDA1 or VSCL1
)
(VSDA1 or VSCL1)
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
7 Parameter Measurement Information
+
+
–
VEN
VEN
IO
–
Source Current
VI - RON*IO
Sink Current
IO
VI + RON*IO
+
–
+
–
VI
VI
B) Current Sink Configuration
A) Current Source Configuration
Figure 7-1. Current Source and Current Sink Configurations for Direct RON Measurements
VCC1
VCC2
200 k
EN
VREF1
VREF2
IO
VI + RON*IO
SCL1/SDA1
SCL2/SDA2
+
–
VI
Figure 7-2. Application Setup for RON Delay
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
VCC1
VCC2
200 k
EN
VCC2
VREF1
VREF2
RL
VO
SCL1/SDA1
SCL2/SDA2
+
VI
–
Figure 7-3. Application Setup for Propagation Delays Delay
SWITCH
S1
S2
USAGE
VT
Translating up
Translating down
RL
S1
VIH
Open
From Output
under Test
VM
VM
S2
Input
VIL
CL
(see Note A)
tPLH
tPHL
VOH
VM
VM
Output
Load Circuit
VOL
NOTES: A. CL includes probe and jig capacitance
B. All input pulses are supplied by generators having the following characteristics: tww G 10 MHz, ZO = 50 Q , tr G 2 ns, tf G 2 ns.
C. The outputs are measured one at a time, with one transition per measurement.
Figure 7-4. Load Circuit for Outputs
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
8 Detailed Description
8.1 Overview
The TCA39306 is a dual bidirectional voltage-level translator compatible with I2C, SMBus, and I3C with an
enable (EN) input, and is operational from 0.9-V to 3.3-V VREF1 and 1.8-V to 5.5-V VREF2
.
The device allows bidirectional voltage translations between 0.85 V and 5 V, without the use of a direction pin.
The low ON-state resistance (RON) of the switch allows connections to be made with minimal propagation delay.
When EN is high, the translator switch is ON, and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2
I/O, respectively, allowing bidirectional data flow between ports. When EN is low, the translator switch is off, and
a high-impedance state exists between ports.
In addition to voltage translation, the TCA39306 can be used to isolate a higher speed bus from a lower speed
bus by controlling the EN pin to disconnect the slower bus during fast-mode communication.
In I2C applications, the bus capacitance limit of 400 pF for Standard and Fast Modes, 550 pF for Fast Mode Plus
restricts the number of devices and bus length. The capacitive load on both sides of the device must be taken
into account when approximating the total load of the system, specifing the sum of both sides is under 400/550
pF.
Both the SDA and SCL channels of the device have the same electrical characteristics, and there is minimal
deviation from one output to another in voltage or propagation delay. This is a benefit over discrete-transistor
voltage-translation solutions, because the fabrication of the switch is symmetrical.
8.1.1 Definition of threshold voltage
This document references a threshold voltage denoted as Vth, which appears multiple times throughout this
document when discussing the NFET between VREF1 and VREF2. The value of Vth is approximately 0.6 V at room
temperature.
8.1.2 Correct Device Set Up
In a normal set up shown in Figure 8-1, the enable pin and VREF2 are shorted together and tied to a 200-kΩ
resistor, and a reference voltage equal to VREF1 plus the FET threshold voltage is established. This reference
voltage is used to help pass lows from one side to another more effectively while still separating the different pull
up voltages on both sides.
VCC2 = +3.3 V
Normal Setup
VCC1 < VCC2
200 kΩ
VCC1 = +1.8 V
EN
+1.8 V + VTH
RPU
RPU
RPU
RPU
+
Vgs
VREF1
VREF2
-
IREF2 = 4 µA
SDA1
SCL1
SDA2
SCL2
Figure 8-1. Normal Setup
Care should be taken to make sure VREF2 has an external resistor tied between it and VCC2. If VREF2 is tied
directly to the VCC2 rail without a resistor, then there is no external resistance from the VCC2 to VCC1 to limit
the current such as in Figure 8-2. This effectively looks like a low impedance path for current to travel through
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
and potentially break the pass FET if the current flowing through the pass FET is larger than the absolute
maximum continuous channel current specified in section 6.1. The continuous channel current is larger with a
higher voltage difference between VCC1 and VCC2
.
Figure 8-2 shows an improper set up. If VCC2 is larger than VCC1 but less than Vth, the impedance between VCC1
and VCC2 is high resulting in a low drain to source current, which does not cause damage to the device. Concern
arises when VCC2 becomes larger than VCC1 by Vth. During this event, the NFET turns on and begin to conduct
current. This current is dependent on the gate to source voltage and drain to source voltage.
VCC2 = +3.3 V
Abnormal Setup
VCC1 < VCC2
200k Ω
VCC1 = +1.8 V
EN
RPU
RPU
RPU
RPU
+
Vgs
VREF1
VREF2
-
SDA1
SCL1
SDA2
SCL2
Figure 8-2. Abnormal Setup
8.1.3 Disconnecting a Responder from the Main Bus Using the EN Pin
TCA39306 can be used as a switch to disconnect one side of the device from the main bus, whether isolating
I3C and I2C devices or different speed groups. This can be advantageous in multiple situations. One instance of
this situation is if there are devices on the I2C bus which only supports fast mode (400 kHz) while other devices
on the bus support fast mode plus (1 MHz). An example of this is displayed in Figure 8-3.
3.3 V I2C bus
(1 MHz)
3.3 V I2C bus
(400 kHz)
TCA39306
EN
GPIO
Note: GPIO logic high must not
exceed 3.3 V +Vth in this example
Figure 8-3. Example of an I2C bus with multiple supported frequencies
In this situation, if the controller is on the 1 MHz side then communicating at 1 MHz should not be attempted
if TCA39306 were enabled. It needs to be disabled for the device to avoid possibly glitching state machines
in devices which were designed to operate correctly at 400 kHz or slower. When the device is disabled, the
controller can communicate with the 1 MHz devices without disturbing the 400 kHz bus. When the device is
enabled, communication across both sides at 400 kHz is acceptable.
8.1.4 Supporting Remote Board Insertion to Backplane with TCA39306
Another situation where TCA39306 is advantageous when using its enable feature is when a remote board with
I2C lines needs to be attached to a main board (backplane) with an I2C bus such as in Figure 8-4. If connecting
a remote board to a backplane is not done properly, the connection could result in data corruption during a
transaction or the insertion could generate an unintended pulse on the SCL line. Which could glitch an I2C
device state machine causing the I2C bus to get stuck.
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
Main Board
3.3 V I2C bus
Remote Board
3.3 V I2C bus
TCA39306
EN
GPIO
Note: GPIO logic high must not
exceed 3.3 V +Vth in this example
Figure 8-4. An example of connecting a remote board to a main board (backplane)
TCA39306 can be used to support this application because it can be disabled while making the connection.
Then it is enabled once the remote board is powered on and the buses on both sides are IDLE.
8.1.5 Switch Configuration
TCA39306 has the capability of being used with its VREF1 voltage equal to VREF2. This essentially turns the
device from a translator to a device which can be used as a switch, and in some situations this can be useful.
The switch configuration is shown in Figure 8-5 and translation mode is shown in Figure 8-6.
VCC2
GPIO: high logic does not
exceed Vref2 + Vth
VCC1
Vref1
200 k
Where Vcc2 = Vcc1
VCC1 VCC1
Vref2
VCC2
VCC2
R
EN
R
R
R
TCA39306
SCL1
SDA1
SCL2
SDA2
Switch Configuration: Vref1=Vref2 and
Enable is controlled by a GPIO
Figure 8-5. Switch Configuration
VCC2
VCC1
200 k
VCC1 VCC1
Vref1
Vref2
EN
VCC2
VCC2
R
R
R
R
TCA39306
SCL1
SDA1
SCL2
SDA2
Translation Configuration
where Vcc2 >= Vref1 + 0.7 V
Figure 8-6. Translation Configuration
When TCA39306 is in the switch configuration (VREF1 = VREF2), the propagation delays are different compared
to the translator configuration. Taking a look at the propagation delays, if the pull up resistance and capacitance
on both sides of the bus are equal, then in switch mode the device has the same propagation delay from side
one to two and side two to one. The propagation delays become lower when VCC1/VCC2 is larger. For example,
the propagation delay at 1.8 V is longer than at 5 V in the switching configuration. When the device is in
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
translation mode, side one propagate lows to side two faster than side two can propagate lows to side 1. This
time difference becomes larger the larger the difference between VCC2 and VCC1 becomes.
8.1.6 Controller on Side 1 or Side 2 of Device
I2C and SMBus are bidirectional protocol meaning devices on the bus can both transmit and receive data.
TCA39306 was designed to allow for signals to be able to be transmitted from either side, thus allowing for
the controller to be able to placed on either side of the device. Figure 8-7 shows the controller on side two as
opposed to the diagram on page 1 of this data sheet.
VCC2
VCC1
200 k
Vref1
Vref2
EN
TCA39306
SCL1
SDA1
SCL2
SDA2
I2C responder
devices
I2C or SMBus
Controller (processor)
Figure 8-7. Controller on side 2
8.1.7 LDO and TCA39306 Concerns
The VREF1 pin can be supplied by a low-dropout regulator (LDO), but in some cases the LDO may lose its
regulation because of the bias current from VREF2 to VREF1. If the LDO cannot sink the bias current, then the
current has no other paths to ground and instead charges up the capacitance on the VREF1 node (both external
and parasitic). This results in an increase in voltage on the VREF1 node. If no other paths for current to flow
are established (such as back biasing of body diodes or clamping diodes through other devices on the VREF1
node), then the VREF1 voltage ends up stabilizing when Vgs of the pass FET is equal to Vth. This means VREF1
node voltage is VCC2 - Vth. Note that any secondary or primaries running off of the LDO now see the VCC2 - Vth
voltage which may cause damage to those secondary or primaries if they are not rated to handle the increased
voltage.
Translator Setup with Vref1
provided by LDO and no path
for bias current
VCC2 = +3.3 V
200 k
VCC1 < VCC2
Ven = Vref1 + VTH
EN
+
+
Vgs
VREF1 = Vcc2 - Vth
Vout
-
LDO
-
VREF1
pin
VREF2
pin
Ibias = (Vcc2 – Ven) / 200 k
CREF1
Figure 8-8. Example of no leakage current path when using LDO
To make sure the LDO does not lose regulation due to the bias current of TCA39306, a weak pull down resistor
can be placed on VREF1 to ground to provide a path for the bias current to travel. The recommended pull down
resistor is calculated by Equation 4 where 0.75 gives about 25% margin for error incase bias current increases
during operation.
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
VCC2 = +3.3 V
Translator Setup
200 k
VCC1 < VCC2
Ven = Vref1 + VTH
EN
+
Vgs
Vout = +1.8 V
-
LDO
VREF1
Rpulldown
Ibias = (Vcc2 – Ven) / 200 k
VREF2
CREF1
Figure 8-9. Example with Leakage current path when using an LDO
Ven = VREF1 + Vth
(1)
where
Vth is approximately 0.6 V
•
Ibias = (VCC2 - Ven)/200 k
(2)
(3)
(4)
Rpulldown = VOUT/Ibias
Recommended Rpulldown = Rpulldown x 0.75
8.1.8 Current Limiting Resistance on VREF2
The resistor is used to limit the current between VREF2 and VREF1 (denoted as RCC) and helps to establish the
reference voltage on the enable pin. The 200k resistor can be changed to a lower value; however, the bias
current proportionally increases as the resistor decreases.
Ibias = (VCC2 - Ven)/RCC : Ven = VREF1 + Vth
(5)
where
Vth is approximately 0.6 V
•
Keep in mind RCC should not be sized low enough that ICC exceeds the absolute maximum continuous channel
current specified in the Absolute Maximum Ratings which is described in Equation 6.
RCC(min) ≥ (VCC2 - Ven)/0.128 : Ven = VREF1 + Vth
(6)
where
Vth is approximately 0.6 V
•
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
8.2 Functional Block Diagram
8.3 Feature Description
8.3.1 Enable (EN) Pin
The device is a double-pole, single-throw switch in which the gate of the transistors is controlled by the voltage
on the EN pin. In Figure 9-1, the device is always enabled when power is applied to VREF2. In Figure 9-2, the
device is enabled when a control signal from a processor is in a logic-high state.
8.3.2 Voltage Translation
The primary feature of the device is translating voltage from an I2C bus referenced to VREF1 up to an I2C bus
referenced to VDPU, to which VREF2 is connected through a 200-kΩ pullup resistor. Translation on a standard,
open-drain I2C bus is achieved by simply connecting pullup resistors from SCL1 and SDA1 to VREF1 and
connecting pullup resistors from SCL2 and SDA2 to VDPU. Information on sizing the pullup resistors can be
found in the Sizing Pullup Resistors section.
8.4 Device Functional Modes
INPUT
TRANSLATOR FUNCTION
EN(1)
Logic Lows are propagated from one side to the other, Logic Highs blocked (independent
H
pull up resistors passively drive the line high)
L
Disconnect
(1) The SCL switch conducts if EN is ≥ 0.6 V higher than SCL1 or SCL2. The same is true of SDA.
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
9 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
9.1 Application Information
9.1.1 General Applications of I2C
As with the standard I2C system, pullup resistors are required to provide the logic-high levels on the translator
bus. The size of these pullup resistors depends on the system, but each side of the repeater must have a pullup
resistor. The device is designed to work with standard-mode and fast-mode I2C devices in addition to SMBus
devices. Standard-mode I2C devices only specify 3 mA in a generic I2C system where standard-mode devices
and multiple controllers are possible. Under certain conditions, high termination currents can be used. When
the SDA1 or SDA2 port is low, the clamp is in the ON state, and a low-resistance connection exists between
the SDA1 and SDA2 ports. Assuming the higher voltage is on the SDA2 port when the SDA2 port is high,
the voltage on the SDA1 port is limited to the voltage set by VREF1. When the SDA1 port is high, the SDA2
port is pulled to the pullup supply voltage of the drain (VDPU) by the pullup resistors. This functionality allows a
seamless translation between higher and lower voltages selected by the user, without the need for directional
control. The SCL1-SCL2 channel also functions in the same way as the SDA1-SDA2 channel.
9.2 Typical Application
Figure 9-1 and Figure 9-2 show how these pullup resistors are connected in a typical application, as well as two
options for connecting the EN pin.
VPU_1 = 1.8 V
VPU_2 = 3.3 V
200 kΩ
TCA39306
SW
RPU
RPU
RPU
RPU
VCC
I2C
VCC
VREF1
SCL1
VREF2
I2C
Responder
EN
Controller
SCL2
SCL
SDA
SCL
SDA1
SDA2
SDA
SW
GND
GND
GND
Figure 9-1. Typical Application Circuit (Switch Always Enabled)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
On
3.3 V EN Signal
Off
VPU_1 = 1.8 V
VPU_2 = 3.3 V
200 k
TCA39306
RPU
RPU
RPU
RPU
VCC
VCC
I2C
VREF1
SCL1
VREF2
EN
I2C
Controller
Responder
SCL
SCL2
SCL
SDA
SW
SDA1
SDA2
SDA
SW
GND
GND
GND
Figure 9-2. Typical Application Circuit (Switch Enable Control)
9.2.1 Design Requirements
MIN TYP(1) MAX UNIT
VREF2
EN
Reference voltage
VREF1 + 0.6
VREF1 + 0.6
0.9
2.1
2.1
1.5
6
5
5
V
V
Enable input voltage
Reference voltage
VREF1
IPASS
IREF
4.4
V
Pass switch current
Reference-transistor current
mA
μA
5
(1) All typical values are at TA = 25°C.
9.2.2 Detailed Design Procedure
9.2.2.1 Bidirectional Voltage Translation
For the bidirectional clamping configuration (higher voltage to lower voltage or lower voltage to higher voltage),
the EN input must be connected to VREF2 and both pins pulled to high-side VDPU through a pullup resistor
(typically 200 kΩ). This allows VREF2 to regulate the EN input. A 100-pF filter capacitor connected to VREF2 is
recommended. The I2C bus controller output can be push-pull or open-drain (pullup resistors may be required)
and the I2C bus device output can be open-drain (pullup resistors are required to pull the SCL2 and SDA2
outputs to VDPU). However, if either output is push-pull, data must be unidirectional or the outputs must be
3-state capable and be controlled by some direction-control mechanism to prevent high-to-low contentions in
either direction. If both outputs are open-drain, no direction control is needed.
9.2.2.2 Sizing Pullup Resistors
To get an estimate for the range of values that can be used for the pullup resistor, please refer to the application
note SLVA689. Figure 9-3 and Figure 9-4 respectively show the maximum and minimum pullup resistance
allowable by the I2C specification for standard-mode (100 kHz) and fast-mode (400 kHz) operation.
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
9.2.2.3 Bandwidth
The maximum frequency of the device depends on the application. The device can operate at speeds of > 100
MHz given the correct conditions. The maximum frequency is dependent upon the loading of the application.
However, this is an analog type of measurement. For digital applications, the signal should not degrade up to the
fifth harmonic of the digital signal. The frequency bandwidth should be at least five times the maximum digital
clock rate. This component of the signal is important in determining the overall shape of the digital signal. In the
case of the device, digital clock frequency of >100 MHz can be achieved.
The device does not provide any drive capability like the TCA9517 or other buffered translators. Therefore,
higher-frequency applications require higher drive strength from the host side. No pullup resistor is needed on
the host side (3.3 V) if the device is being driven by standard CMOS push-pull output driver. Ideally, it is best to
minimize the trace length from device on the sink side (1.8 V) to minimize signal degradation.
You can then use a simple formula to compute the maximum practical frequency component or the knee
frequency (fknee). All fast edges have an infinite spectrum of frequency components. However, there is an
inflection (or knee) in the frequency spectrum of fast edges where frequency components higher than fknee are
insignificant in determining the shape of the signal.
To calculate fknee
:
fknee = 0.5 / RT (10%–90%)
fknee = 0.4 / RT (20%–80%)
(7)
(8)
For signals with rise-time characteristics based on 10- to 90-percent thresholds, fknee is equal to 0.5 divided by
the rise time of the signal. For signals with rise-time characteristics based on 20- to 80-percent thresholds, which
is very common in many current device specifications, fknee is equal to 0.4 divided by the rise time of the signal.
Some guidelines to follow that help maximize the performance of the device:
•
•
Keep trace length to a minimum by placing the device close to the I2C output of the processor.
The trace length should be less than half the time of flight to reduce ringing and line reflections or non-
monotonic behavior in the switching region.
•
To reduce overshoots, a pullup resistor can be added on the 1.8 V side; be aware that a slower fall time is to
be expected.
9.2.3 Application Curve
VDPUX < 2 V
VDPUX > 2 V
Standard mode
(fSCL = 100 kHz,
tr = 1 μs)
Fast mode
Fast mode plus
(fSCL = 1000 kHz,
tr = 120 ns)
VOL = 0.2 x VDPUX , IOL = 2 mA when VDPUX ≤ 2 V
VOL = 0.4 V, IOL = 3 mA when VDPUX > 2 V
(fSCL = 400 kHz,
tr = 300 ns)
Figure 9-4. Minimum Pullup Resistance (Rp(min)) vs
Figure 9-3. Maximum Pullup Resistance (Rp(max)
)
Pullup Reference Voltage (VDPUX
)
vs Bus Capacitance (Cb)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
9.3 Systems Examples: I3C Usage Considerations
The TCA39306 has bandwidth to support the high speeds needed for I3C, but there are special considerations
which are required. Since I3C uses both push-pull and open-drain, it may not be possible to support all I3C
applications with a FET-based translator.
9.3.1 I3C Bus Switching
Bus switching is when the bus path is enabled or disabled, but does not translate the bus voltage. External
pull-up resistors are not needed for I3C, because the controller enables or disables the pull-up resistor on the
SDA line. This presents a unique challenge for FET-based translators, like the TCA39306, because they rely on
a pull-up resistor to pull the output side of the switch all the way to supply. For the switching use case, there is no
translation, but the enable voltage must be high enough for the switch to stay on for the entire voltage range of
the bus (0 V to bus voltage).
RON must be low enough for the full push-pull voltage range. The EN voltage must be at least 1 Vt (~0.6 V)
above the maximum desired pass-voltage. This comes out to VEN ≥ VBUS + 0.6 V. Since the switch enable
voltage is being directly controlled, the VREF1 and VREF2 pins are not needed, and can be shorted to ground to
improve power consumption.
It is possible to control the EN pin with a voltage equal to VBUS, but external pull-up resistors on the downstream
side are a requirement to ensure the bus is pulled entirely to VBUS
.
On
VEN VBUS + 0.6 V
Off
TCA39306
VCC
VCC
VREF1
SCL1
VREF2
EN
I3C
Controller
I3C
Responder
SCL2
SCL
SDA
SCL
SW
SDA1
SDA2
SDA
SW
GND
GND
GND
Figure 9-5. I3C Bus Switching Application (Without Pull-up Resistors)
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
On
VEN = VBUS
Off
VBUS = 3.3 V
TCA39306
SW
RPU
RPU
RPU
RPU
VCC
I3C
VCC
VREF1
SCL1
VREF2
EN
I3C
Responder
SCL
Controller
SCL2
SCL
SDA
SDA1
SDA2
SDA
GND
SW
GND
GND
Figure 9-6. I3C Bus Switching Application (With Pull-up Resistors)
9.3.2 I3C Bus Voltage Translation
Bus voltage translation is when the bus voltage is translated up or down. This presents a unique challenge
with I3C for FET-based translators, like the TCA39306, because they rely on a pull-up resistor to translate
the voltage up from the low-voltage side. The pull-up resistor selected must be strong enough to meet the
timing requirements (based on bus capacitance and translation voltages), but not so strong to violate the VIL
requirements of the I3C devices.
The pull-up resistors are needed on both sides. The reason for this is that with the normal translation setup,
the switch is "on" when either side's bus voltage drops to roughly VPU_1. This means that the pull-up resistors
are required to pull the bus voltage on the high-voltage side from VPU_1 to VPU_2. When the device on the
high-voltage side is controlling the bus, the switch will turn off at VPU_1. The pull-up resistors on the low-voltage
side are used to bleed off any additional current that might "leak" through the switch.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
VPU_1 = 1.8 V
VPU_2 = 3.3 V
200 kΩ
TCA39306
SW
RPU
RPU
RPU
RPU
VCC
VCC
VREF1
SCL1
VREF2
EN
I3C
Controller
I3C
Responder
SCL
SCL2
SCL
SDA
SDA1
SDA2
SDA
SW
GND
GND
GND
Figure 9-7. I3C Bus Translation
10 Power Supply Recommendations
For supplying power to the device, the VREF1 pin can be connected directly to a power supply. The VREF2 pin
must be connected to the VDPU power supply through a 200-kΩ resistor. Failure to have a high-impedance
resistor between VREF2 and VDPU results in excessive current draw and unreliable device operation. It is also
worth noting, that in order to support voltage translation, the device must have the EN and VREF2 pins shorted
and then pulled up to VDPU through a high-impedance resistor.
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
11 Layout
11.1 Layout Guidelines
For printed-circuit board (PCB) layout of the device, common PCB layout practices should be followed, but
additional concerns related to high-speed data transfer such as matched impedances and differential pairs are
not a concern for I2C signal speeds.
In all PCB layouts, it is a best practice to avoid right angles in signal traces, to fan out signal traces away from
each other on leaving the vicinity of an integrated circuit (IC), and to use thicker trace widths to carry higher
amounts of current that commonly pass through power and ground traces. The 100-pF filter capacitor should be
placed as close to VREF2 as possible. A larger decoupling capacitor can also be used, but a longer time constant
of two capacitors and the 200-kΩ resistor results in longer turnon and turnoff times for the TCA39306 device.
These best practices are shown in Figure 11-1.
For the layout example provided in Figure 11-1, it would be possible to fabricate a PCB with only two layers by
using the top layer for signal routing and the bottom layer as a split plane for power (VCC) and ground (GND).
However, a four-layer board is preferable for boards with higher-density signal routing. On a four-layer PCB,
it is common to route signals on the top and bottom layer, dedicate one internal layer to a ground plane, and
dedicate the other internal layer to a power plane. In a board layout using planes or split planes for power and
ground, vias are placed directly next to the surface-mount component pad, which must attach to VCC or GND,
and the via is connected electrically to the internal layer or the other side of the board. Vias are also used when
a signal trace must be routed to the opposite side of the board, but this technique is not demonstrated in Figure
11-1.
11.2 Layout Example
Figure 11-1. Layout Example
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TCA39306
TCA39306
SCPS274A – JUNE 2021 – REVISED AUGUST 2021
www.ti.com
12 Device and Documentation Support
12.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.2 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.3 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
12.5 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most-
current data available for the designated device. This data is subject to change without notice and without
revision of this document. For browser-based versions of this data sheet, see the left-hand navigation pane.
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TCA39306
PACKAGE OPTION ADDENDUM
www.ti.com
3-Oct-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TCA39306DCUR
TCA39306DTMR
ACTIVE
ACTIVE
VSSOP
X2SON
DCU
DTM
8
8
3000 RoHS & Green
5000 RoHS & Green
NIPDAUAG | SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
(2GPT, 2GVI)
1IH
NIPDAUAG
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Oct-2021
OTHER QUALIFIED VERSIONS OF TCA39306 :
Automotive : TCA39306-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TCA39306DCUR
TCA39306DTMR
VSSOP
X2SON
DCU
DTM
8
8
3000
5000
178.0
178.0
9.0
8.4
2.25
0.93
3.35
1.49
1.05
0.43
4.0
2.0
8.0
8.0
Q3
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TCA39306DCUR
TCA39306DTMR
VSSOP
X2SON
DCU
DTM
8
8
3000
5000
180.0
205.0
180.0
200.0
18.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
相关型号:
TCA4027036AA005000-10M
Clipped Sine Output Oscillator, 10MHz Nom, ROHS COMPLIANT, CERAMIC, LCC-4
PLETRONICS
TCA4027036AA010000-40.0M
Clipped Sine Output Oscillator, 40MHz Nom, ROHS COMPLIANT, CERAMIC, LCC-4
PLETRONICS
TCA4027036AA010000-FREQ
Clipped Sine Output Oscillator, 10MHz Min, 40MHz Max, ROHS COMPLIANT, CERAMIC, LCC-4
PLETRONICS
TCA4027036AA010008-FREQ
Clipped Sine Output Oscillator, 10MHz Min, 26MHz Max, ROHS COMPLIANT, CERAMIC, LCC-4
PLETRONICS
©2020 ICPDF网 联系我们和版权申明