TCAN1044ADRBRQ1 [TI]
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode;型号: | TCAN1044ADRBRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode |
文件: | 总41页 (文件大小:2505K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD
Transceiver with Standby mode
1 Features
3 Description
•
•
•
AEC-Q100 (Grade 1) Qualified for automotive
applications
Meets the requirements of ISO 11898-2:2016
physical layer standard
Functional Safety-Capable
– Documentation available to aid in functional
safety system design
Support of classical CAN and optimized CAN FD
performance at 2, 5, and 8 Mbps
– Short and symmetrical propagation delays for
enhanced timing margin
TCAN1044AV I/O voltage range supports 1.7 V to
5.5 V
Support for 12-V and 24-V battery applications
Receiver common mode input voltage: ±12 V
Protection features:
The TCAN1044A-Q1 and TCAN1044AV-Q1 are high
speed controller area network (CAN) transceivers that
meets the physical layer requirements of the ISO
11898-2:2016 high-speed CAN specification.
The transceivers have certified electromagnetic
compatibility (EMC) operation making it an ideal
choice for classical CAN and CAN FD networks up
to 5 megabits per second (Mbps). Up to 8 Mbps
operation in simpler networks is possible with these
devices. The TCAN1044AV-Q1 includes internal logic
level translation via the VIO pin to allow for interfacing
the transceiver I/O's directly to 1.8-V, 2.5-V, 3.3-V, or
5-V logic levels. The transceiver supports a low-power
standby mode and wake over CAN which is compliant
to the ISO 11898-2:2016 defined wake-up pattern
(WUP).
•
•
•
•
•
– Bus fault protection: ±58 V
The transceivers also include thermal-shutdown
(TSD), TXD-dominant time-out (DTO), supply
undervoltage detection, and ±58-V bus fault
protection. The devices have defined fail-safe
behavior in supply undervoltage or floating pin
scenarios. These transceivers are not only available
in industry-standard SOIC-8 and VSON-8 packages,
but also have a space-saving small footprint SOT-23
package option.
– Undervoltage protection
– TXD-dominant time-out (DTO)
•
Data rates down to 9.2 kbps
– Thermal-shutdown protection (TSD)
Operating modes:
– Normal mode
– Low power standby mode supporting remote
wake-up request
Optimized behavior when unpowered
– Bus and logic pins are high impedance (no load
to operating bus or application)
– Hot-plug capable: power up/down glitch-free
operation on bus and RXD output
8-Pin SOIC, small footprint SOT-23 and leadless
VSON-8 package with improved automated optical
inspection (AOI) capability
•
•
Device Information
PART NUMBER
PACKAGE(1)
BODY SIZE (NOM)
4.90 mm x 3.91 mm
3.00 mm x 3.00 mm
2.90 mm x 1.60 mm
SOIC (D)
TCAN1044A-Q1
TCAN1044AV-Q1
VSON (DRB)
SOT-23 (DDF)
•
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
2 Applications
VBAT
VOUT
VIN
•
Automotive and transportation
– Body control modules
5-V Voltage
Regulator
3
VCC
VDD
7
CANH
8
STB
– Automotive gateway
MCU
TCAN1044AV
– Advanced driver assistance system (ADAS)
– Infotainment
4
1
VIN
CAN FD
RXD
TXD
6
Controller
CANL
VIO
GND
1.8 V / 2.5
V
Regulator
/ 3.3
V
5
VOUT
Optional:
Terminating Node
Optional: Filtering,
Transient and ESD
Simplified Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Device Comparison.........................................................3
6 Pin Configuration and Functions...................................3
7 Specifications.................................................................. 4
7.1 Absolute Maximum Ratings ....................................... 4
7.2 ESD Ratings .............................................................. 4
7.3 ESD Ratings - IEC Specifications ..............................4
7.4 Recommended Operating Conditions ........................4
7.5 Thermal Characteristics .............................................5
7.6 Supply Characteristics ............................................... 5
7.7 Dissipation Ratings .................................................... 6
7.8 Electrical Characteristics ............................................6
7.9 Switching Characteristics ...........................................8
7.10 Typical Characteristics............................................10
8 Parameter Measurement Information.......................... 11
9 Detailed Description......................................................14
9.1 Overview...................................................................14
9.2 Functional Block Diagram.........................................15
9.3 Feature Description...................................................15
9.4 Device Functional Modes..........................................19
10 Application Information Disclaimer...........................22
10.1 Application Information........................................... 22
10.2 Typical Application.................................................. 22
10.3 System Examples................................................... 24
11 Power Supply Recommendations..............................24
12 Layout...........................................................................25
12.1 Layout Guidelines................................................... 25
12.2 Layout Example...................................................... 25
13 Device and Documentation Support..........................26
13.1 Receiving Notification of Documentation Updates..26
13.2 Support Resources................................................. 26
13.3 Trademarks.............................................................26
13.4 Electrostatic Discharge Caution..............................26
13.5 Glossary..................................................................26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (October 2021) to Revision C (December 2021)
Page
•
•
Changed ICC (mA) to ICC (µA) in Figure 7-3 .....................................................................................................10
Changed IIO (mA) to IIO (µA) in Figure 7-4 .......................................................................................................10
Changes from Revision A (July 2021) to Revision B (October 2021)
Page
•
Deleted Product Preview from the D and DDF packages in the Device Information table.................................1
Changes from Revision * (February 2021) to Revision A (July 2021)
Page
•
Changed the document status from: Advanced Information to: Production data............................................... 1
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
5 Device Comparison
Table 5-1. Device Comparison Table
Part Number
Low Voltage I/O Logic Support on Pin 5
Pin 8 Mode Selection
TCAN1044A-Q1
TCAN1044AV-Q1
No
Low Power Standby Mode with Remote
Wake
Yes
6 Pin Configuration and Functions
TXD
GND
VCC
1
2
3
4
8
7
6
5
STB
TXD
GND
VCC
1
2
3
4
8
7
6
5
STB
CANH
CANL
NC, VIO
CANH
CANL
NC, VIO
RXD
RXD
Not to scale
Not to scale
Figure 6-1. DDF Package, 8-Pin SOT, Top View
Figure 6-2. D Package, 8-Pin SOIC, Top VIew
TXD
GND
VCC
1
2
3
4
8
7
6
5
STB
CANH
CANL
NC,VIO
Thermal
Pad
RXD
Not to scale
Figure 6-3. DRB Package, 8-Pin VSON, Top View
Table 6-1. Pin Functions
Pins
Type
Description
Name
TXD
GND
VCC
No.
1
Digital Input CAN transmit data input; integrated pull-up
2
GND
Ground connection
5-V supply voltage
3
Supply
RXD
NC
4
Digital Output CAN receive data output, tri-stated when device powered off
—
Not internally connected; Devices without VIO
I/O supply voltage for devices with suffix 'V'
Low-level CAN bus input/output line
5
VIO
Supply
Bus IO
Bus IO
CANL
CANH
STB
6
7
8
High-level CAN bus input/output line
Digital Input Standby input for mode control; integrated pull-up
Connect the thermal pad to any internal PCB ground plane using multiple vias for optimal
thermal performance.
Thermal Pad (VSON only)
—
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
(1) (2)
MIN
–0.3
–0.3
–58
–45
–0.3
–0.3
–8
MAX
UNIT
V
VCC
Supply voltage
6
6
VIO
Supply voltage I/O level shifter
CAN Bus I/O voltage
V
VBUS
VDIFF
VLogic_Input
VRXD
IO(RXD)
TJ
58
45
6
V
Max differential voltage between CANH and CANL
Logic input terminal voltage
RXD output terminal voltage range
RXD output current
V
V
6
V
8
mA
°C
°C
Junction temperature
–40
–65
165
150
TSTG
Storage temperature
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions.
If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully
functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.
(2) All voltage values, except differential I/O bus voltages, are with respect to ground terminal.
7.2 ESD Ratings
VALUE
UNIT
HBM classification level 3A for
all pins
±4000
V
Human-body model (HBM), per AEC Q100-002(1)
HBM classification level 3B for
global pins CANH and CANL
with respect to GND
VESD
Electrostatic discharge
±10000
±750
V
V
Charged-device model (CDM), per AEC Q100-011
CDM classification level C5 for all pins
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
7.3 ESD Ratings - IEC Specifications
VALUE
UNIT
Unpowered contact discharge
per ISO 10605 (1)
±8000
±8000
V
V
V
SAE J2962-2 per ISO 10605
VESD System level Electrostatic discharge
Powered Contact Discharge
(2)
SAE J2962-2 per ISO 10605
Powered Air Discharge (2)
±15000
CAN bus terminals to GND
Pulse 1
–100
75
V
V
V
V
V
Pulse 2a
Transient voltage per ISO 7637-2(3)
VTran
Pulse 3a
–150
100
±30
Pulse 3b
Transient voltage per ISO 7637-3(4)
DCC slow transient pulse
(1) Tested according to IEC 62228-3:2019 CAN Transceivers.
(2) Results given here are specific to the SAE J2962-2 Communication Transceivers Qualification Requirements - CAN. Testing performed
by OEM approved independent third party, EMC report available upon request.
(3) Tested according to IEC 62228-3:2019 CAN Transceivers.
(4) Tested according to SAE J2962-2.
7.4 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
VCC
Supply voltage
4.5
5
5.5
V
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7.4 Recommended Operating Conditions (continued)
MIN
1.7
NOM
MAX
UNIT
V
VIO
Supply voltage for I/O level shifter
5.5
IOH(RXD)
IOL(RXD)
IOH(RXD)
IOL(RXD)
TJ
RXD terminal high-level output current, Devices with VIO
RXD terminal low-level output current, Devices with VIO
RXD terminal high-level output current, Devices without VIO
RXD terminal low-level output current, Devices without VIO
Operating junction temperature
–1.5
mA
mA
mA
mA
℃
1.5
–2
2
-40
150
7.5 Thermal Characteristics
TCAN1044Ax-Q1
DDF (SOT)
THERMAL METRIC(1)
UNIT
D (SOIC)
DRB (VSON)
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
127.5
67.6
70.9
19.3
70.2
--
122
63
55.2
℃/W
℃/W
℃/W
℃/W
℃/W
℃/W
RθJC(top)
RθJB
62.4
27.5
2.3
42.4
2.4
42.2
--
ΨJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ΨJB
27.4
11.5
RθJC(bot)
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
7.6 Supply Characteristics
Over recommended operating conditions with TJ = -40℃ to 150℃ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
STB = 0 V, TXD = 0 V
RL = 60 Ω, CL = open
See Figure 8-1
45
70
mA
Dominant
Recessive
STB = 0 V, TXD = 0 V
RL = 50 Ω, CL = open
See Figure 8-1
49
80
mA
mA
Supply current
Normal mode
STB = 0 V, TXD = VCC or VIO
RL = 50 Ω, CL = open
See Figure 8-1
4.5
7.5
ICC
STB = 0 V, TXD = 0 V
CANH = CANL = ±25 V
RL = open, CL = open
See Figure 8-1
Dominant with
bus fault
130
mA
Supply current
Standby mode
Devices with VIO
STB = TXD = VIO
RL = 50 Ω, CL = open
See Figure 8-1
1.5
15
µA
µA
Supply current
Standby mode
Devices without VIO
STB = TXD = VCC
RL = 50 Ω, CL = open
See Figure 8-1
I/O supply current
Normal mode
STB = 0 V, TXD = 0 V
RXD floating
Dominant
Recessive
125
25
300
48
µA
µA
µA
I/O supply current
Normal mode
STB = 0 V, TXD = 0 V
RXD floating
IIO
I/O supply current
Standby mode
STB = VIO, TXD = 0 V
RXD floating
8.5
14
Rising undervoltage detection on VCC for protected mode
Falling undervoltage detection on VCC for protected mode
Hysteresis voltage on UVCC
4.2
4
4.4
V
V
UVCC
3.5
1.4
4.25
VHYS(UVCC)
UVVIO
200
1.56
1.51
40
mV
V
Rising undervoltage detection on VIO (Devices with VIO
)
1.65
1.59
Falling undervoltage detection on VIO (Devices with VIO
Hysteresis voltage on UVIO
)
V
VHYS(UVIO)
mV
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7.7 Dissipation Ratings
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VCC = 5 V, VIO = 1.8 V, TJ = 27°C, RL = 60 Ω,
CL_RXD = 15 pF
TXD input = 250 kHz 50% duty cycle square
wave
95
mW
VCC = 5 V, VIO = 3.3 V, TJ = 27°C, RL = 60 Ω,
CL_RXD = 15 pF
TXD input = 250 kHz 50% duty cycle square
wave
95
95
mW
mW
mW
mW
VCC = 5 V, VIO = 5 V, TJ = 27°C, RL = 60 Ω,
CL_RXD = 15 pF
TXD input = 250 kHz 50% duty cycle square
wave
Average power dissipation
Normal mode
PD
VCC = 5.5 V, VIO = 1.8 V, TJ = 150°C, RL = 60Ω,
CL_RXD = 15 pF
TXD input = 2.5 MHz 50% duty cycle square
wave
120
120
120
VCC = 5.5 V, VIO = 3.3 V, TJ = 150°C, RL = 60 Ω,
CL_RXD = 15 pF
TXD input = 2.5 MHz 50% duty cycle square
wave
VCC = 5.5 V, VIO = 5 V, TJ = 150°C, RL = 60 Ω,
CL_RXD = 15 pF
TXD input = 2.5 MHz 50% duty cycle square
wave
mW
°C
TTSD
Thermal shutdown temperature
175
195
12
210
TTSD(HYS) Thermal shutdown hysteresis
7.8 Electrical Characteristics
Over recommended operating conditions with TJ = -40℃ to 150℃ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Driver Electrical Characteristics
CANH
CANL
STB = 0 V, TXD = 0 V
50 Ω ≤ RL ≤ 65 Ω, CL = open, RCM = open
See Figure 8-2 and Figure 9-3
2.75
0.5
4.5
V
V
Dominant output voltage
Normal mode
VO(DOM)
2.25
STB = 0 V, TXD = VIO
CANH and CANL RL = open (no load), RCM = open
See Figure 8-2 and Figure 9-3
Recessive output voltage
Normal mode
VO(REC)
2
0.5 VCC
3
V
STB = 0 V, TXD = 250 kHz, 1 MHz, 2.5
MHz
RL = 60 Ω, CSPLIT = 4.7 nF, CL = open,
RCM = open
Driver symmetry
(VO(CANH) + VO(CANL))/VCC
VSYM
0.9
1.1 V/V
400 mV
See Figure 8-2 and Figure 10-2
STB = 0 V
RL = 60 Ω, CL = open
See Figure 8-2 and Figure 9-3
DC output symmetry
(VCC - VO(CANH) - VO(CANL)
VSYM_DC
–400
1.5
)
STB = 0 V, TXD = 0 V
50 Ω ≤ RL ≤ 65 Ω, CL = open
See Figure 8-2 and Figure 9-3
3
3.3
5
V
V
V
Differential output voltage
Normal mode
Dominant
STB = 0 V, TXD = 0 V
45 Ω ≤ RL ≤ 70 Ω, CL = open
See Figure 8-2 and Figure 9-3
VOD(DOM)
CANH - CANL
1.4
STB = 0 V, TXD = 0 V
RL = 2240 Ω, CL = open
See Figure 8-2 and Figure 9-3
1.5
STB = 0 V, TXD = VIO
RL = 60 Ω, CL = open
See Figure 8-2 and Figure 9-3
–120
–50
12 mV
50 mV
Differential output voltage
Normal mode
Recessive
VOD(REC)
CANH - CANL
STB = 0 V, TXD = VIO
RL = open, CL = open
See Figure 8-2 and Figure 9-3
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7.8 Electrical Characteristics (continued)
Over recommended operating conditions with TJ = -40℃ to 150℃ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
-0.1
-0.1
-0.2
TYP
MAX UNIT
CANH
0.1
0.1
0.2
V
V
V
STB = VIO
RL = open
Bus output voltage
Standby mode
VO(STB)
CANL
See Figure 8-2 and Figure 9-3
CANH - CANL
STB = 0 V, TXD = 0 V
V(CANH) = -15 V to 40 V, CANL = open
See Figure 8-7 and Figure 9-3
–115
mA
Short-circuit steady-state output current,
dominant
Normal mode
IOS(SS_DOM)
STB = 0 V, TXD = 0 V
V(CAN_L) = -15 V to 40 V, CANH = open
See Figure 8-7 and Figure 9-3
115 mA
STB = 0 V, TXD = VIO
–27 V ≤ VBUS ≤ 32 V, where VBUS = CANH
= CANL
Short-circuit steady-state output current,
recessive
Normal mode
IOS(SS_REC)
–5
5
mA
See Figure 8-7 and Figure 9-3
Receiver Electrical Characteristics
STB = 0 V
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Input threshold voltage
Normal mode
VIT
500
400
0.9
-4
900 mV
STB = VIO
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Input threshold
VIT(STB)
1150 mV
Standby mode
STB = 0 V
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Dominant state differential input voltage range
Normal mode
VDOM
9
0.5
9
V
V
STB = 0 V
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Recessive state differential input voltage range
Normal mode
VREC
STB = VIO
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Dominant state differential input voltage range
Standby mode
VDOM(STB)
1.15
-4
V
STB = VIO
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Recessive state differential input voltage range
Standby mode
VREC(STB)
0.4
V
STB = 0 V
-12 V ≤ VCM ≤ 12 V
See Figure 8-3 and Table 9-6
Hysteresis voltage for input threshold
Normal mode
VHYS
115
mV
Common-mode range
Normal and standby modes
VCM
See Figure 8-3 and Table 9-6
–12
12
5
V
ILKG(IOFF)
CI
Unpowered bus input leakage current
Input capacitance to ground (CANH or CANL)
Differential input capacitance
CANH = CANL = 5 V, VCC = VIO = GND
µA
20 pF
10 pF
90 kΩ
(1)
TXD = VIO
CID
RID
Differential input resistance
40
20
(1)
STB = 0 V, TXD = VIO
Single-ended input resistance
(CANH or CANL)
-12 V ≤ VCM ≤ 12 V
RIN
45 kΩ
Input resistance matching
[1 – (RIN(CANH) / RIN(CANL))] × 100 %
RIN(M)
V(CAN_H) = V(CAN_L) = 5 V
–1
1
%
TXD Terminal (CAN Transmit Data Input)
VIH
VIH
VIL
VIL
IIH
High-level input voltage
High-level input voltage
Low-level input voltage
Low-level input voltage
High-level input leakage current
Devices without VIO
Devices with VIO
0.7 VCC
0.7 VIO
V
V
Devices without VIO
Devices with VIO
0.3 VCC
0.3 VIO
1
V
V
TXD = VCC = VIO = 5.5 V
–2.5
0
µA
TXD = 0 V
VCC= VIO = 5.5 V
IIL
Low-level input leakage current
–200
-100
–20 µA
TXD = 5.5 V
VCC= VIO = 0 V
ILKG(OFF)
CI
Unpowered leakage current
Input capacitance
–1
0
5
1
µA
pF
VIN = 0.4×sin(2×π×2×106×t)+2.5 V
RXD Terminal (CAN Receive Data Output)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7.8 Electrical Characteristics (continued)
Over recommended operating conditions with TJ = -40℃ to 150℃ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
IO = –2 mA
VOH
VOH
VOL
High-level output voltage
Devices without VIO
See Figure 8-3
0.8 VCC
V
IO = –1.5 mA
Devices with VIO
See Figure 8-3
High-level output voltage
Low-level output voltage
0.8 VIO
V
IO = 2 mA
Devices without VIO
See Figure 8-3
0.2 VCC
V
IO = 1.5mA
VOL
Low-level output voltage
Devices with VIO
See Figure 8-3
0.2 VIO
V
RXD = 5.5 V
VCC = VIO = 0 V
ILKG(OFF)
Unpowered leakage current
–1
0
1
µA
STB Terminal (Standby Mode Input)
VIH
VIH
VIL
VIL
IIH
High-level input voltage
High-level input voltage
Low-level input voltage
Low-level input voltage
High-level input leakage current
Devices without VIO
Devices with VIO
0.7 VCC
0.7 VIO
V
V
Devices without VIO
Devices with VIO
0.3 VCC
0.3 VIO
2
V
V
VCC = VIO = STB = 5.5 V
–2
µA
STB = 0 V
VCC = VIO = 5.5 V,
IIL
Low-level input leakage current
Unpowered leakage current
–20
–2 µA
STB = 5.5V
VCC = VIO = 0 V
ILKG(OFF)
–1
0
1
µA
(1) VIO = VCC in non-V variants of device
7.9 Switching Characteristics
Over recommended operating conditions with TJ = -40℃ to 150℃ (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Device Switching Characteristics
Total loop delay
Driver input (TXD) to receiver output (RXD),
recessive to dominant
STB = 0 V, VIO = 2.8 V to 5.5 V
RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF
See Figure 8-4
tPROP(LOOP1)
tPROP(LOOP1)
tPROP(LOOP2)
125
165
150
180
210
255
210
ns
ns
ns
Total loop delay
Driver input (TXD) to receiver output (RXD),
recessive to dominant
STB = 0 V, VIO = 1.7 V
RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF
See Figure 8-4
Total loop delay
Driver input (TXD) to receiver output (RXD),
dominant to recessive
STB = 0 V, VIO = 2.8 V to 5.5 V
RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF
See Figure 8-4
Total loop delay
Driver input (TXD) to receiver output (RXD),
dominant to recessive
STB = 0 V, VIO = 1.7 V
RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF
See Figure 8-4
tPROP(LOOP2)
255
20
ns
µs
Mode change time, from normal to standby or from
standby to normal
tMODE
See Figure 8-5
See Figure 9-5
tWK_FILTER
Filter time for a valid wake-up pattern
Bus wake-up timeout
0.5
0.8
1.8
6
µs
tWK_TIMEOUT
ms
Driver Switching Characteristics
Propagation delay time, high TXD to driver
recessive (dominant to recessive)
tpHR
tpLD
80
70
ns
ns
Propagation delay time, low TXD to driver dominant
(recessive to dominant)
STB = 0 V
RL = 60 Ω, CL = 100 pF
See Figure 8-2
tsk(p)
Pulse skew (|tpHR - tpLD|)
Differential output signal rise time
Differential output signal fall time
Dominant timeout
14
28
50
ns
ns
ns
ms
tR
tF
tTXD_DTO
See Figure 8-6
1.2
4.0
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7.9 Switching Characteristics (continued)
Over recommended operating conditions with TJ = -40℃ to 150℃ (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Receiver Switching Characteristics
Propagation delay time, bus recessive input to high
output (dominant to recessive)
tpRH
tpDL
81
66
ns
ns
STB = 0 V
CL(RXD) = 15 pF
See Figure 8-3
Propagation delay time, bus dominant input to low
output (recessive to dominant)
tR
tF
RXD output signal rise time
RXD output signal fall time
10
10
ns
ns
FD Timing Characteristics
Bit time on CAN bus output pins
450
160
85
525
205
130
540
210
135
20
ns
ns
ns
ns
ns
ns
ns
ns
ns
tBIT(TXD) = 500 ns
Bit time on CAN bus output pins
tBIT(TXD) = 200 ns
tBIT(BUS)
tBIT(RXD)
ΔtREC
Bit time on CAN bus output pins
tBIT(TXD) = 125 ns(1)
Bit time on RXD output pins
tBIT(TXD) = 500 ns
410
130
75
STB = 0 V
Bit time on RXD output pins
tBIT(TXD) = 200 ns
RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF
ΔtREC = tBIT(RXD) - tBIT(BUS)
See Figure 8-4
Bit time on RXD output pins
tBIT(TXD) = 125 ns(1)
Receiver timing symmetry
tBIT(TXD) = 500 ns
-50
-40
-40
Receiver timing symmetry
tBIT(TXD) = 200 ns
10
Receiver timing symmetry
tBIT(TXD) = 125 ns(1)
10
(1) Measured during characterization and not an ISO 11898-2:2016 parameter.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
7.10 Typical Characteristics
2.5
3
2.5
2
2.3
2.1
1.9
1.7
1.5
1.5
1
-40 -20
0
20
40
60
Temperature (°C)
80 100 120 140 160
4.5 4.6 4.7 4.8 4.9
5
VCC (V)
5.1 5.2 5.3 5.4 5.5
VCC = 5 V
VIO = 3.3 V
RL = 60 Ω
Temp = 25°C
Figure 7-2. VOD(DOM) vs VCC
RL = 60 Ω
Figure 7-1. VOD(DOM) vs Temperature
VCC = 5 V
VIO = 3.3 V
RL = 60 Ω
VCC = 5 V
VIO = 3.3 V
RL = 60 Ω
Figure 7-3. ICC Standby vs Temperature
Figure 7-4. IIO Standby vs Temperature
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
8 Parameter Measurement Information
CANH
TXD
RL
CL
CANL
Figure 8-1. ICC Test Circuit
RCM
CANH
50%
50%
TXD
TXD
RL
CL
VOD
VCM
VCC
VO(CANH)
tpLD
tpHR
90%
10%
0V
CANL
RCM
0.9V
VO(CANL)
VOD
0.5V
tR
tF
Figure 8-2. Driver Test Circuit and Measurement
CANH
1.5V
0.9V
VID
IO
RXD
0.5V
0V
VID
tpDL
tpRH
CL_RXD
VOH
VO
CANL
90%
VO(RXD)
50%
10%
VOL
tF
tR
Figure 8-3. Receiver Test Circuit and Measurement
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
TXD
VI
70%
tLOOP1
30%
30%
CANH
0 V
TXD
VI
RL
CL
tBIT(TXD)
5 x tBIT(TXD)
CANL
tBIT(BUS)
STB
RXD
0 V
900 mV
500 mV
+
VDIFF
VO
CL_RXD
œ
RXD
VOH
70%
30%
VOL
tBIT(RXD)
tLOOP2
Figure 8-4. Transmitter and Receiver Timing Test Circuit and Measurement
CANH
VIH
TXD
CL
0V
RL
STB
50%
CANL
STB
VI
0V
tMODE
RXD
VOH
VO
CL_RXD
RXD
50%
VOL
Figure 8-5. tMODE Test Circuit and Measurement
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
VIH
0V
CANH
TXD
TXD
RL
CL
VOD
VOD(D)
CANL
0.9V
VOD
0.5V
0V
tTXD_DTO
Figure 8-6. TXD Dominant Timeout Test Circuit and Measurement
200 ꢀs
IOS
CANH
TXD
VBUS
IOS
CANL
VBUS
VBUS
0V
or
0V
VBUS
VBUS
Figure 8-7. Driver Short-Circuit Current Test and Measurement
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
9 Detailed Description
9.1 Overview
The TCAN1044A(V)-Q1 devices meet or exceed the specifications of the ISO 11898-2:2016 high speed CAN
(Controller Area Network) physical layer standard. The devices have been certified to the requirements of ISO
11898-2:2016 physical layer requirements according to the GIFT/ICT high speed CAN test specification. The
transceivers provide a number of different protection features making them ideal for the stringent automotive
system requirements while also supporting CAN FD data rates up to 8 Mbps.
The TCAN1044A(V)-Q1 support the following CAN and CAN FD standards:
•
Physical layer:
– ISO 11898-2:2016 High speed medium access unit
– ISO 11898-5:2007 High speed medium access unit with low-power mode
– SAE J2284-1: High Speed CAN (HSC) for Vehicle Applications at 125 kbps
– SAE J2284-2: High Speed CAN (HSC) for Vehicle Applications at 250 kbps
– SAE J2284-3: High Speed CAN (HSC) for Vehicle Applications at 500 kbps
– SAE J2284-4: High-Speed CAN (HSC) for Vehicle Applications at 500 kbps with CAN FD Data at 2 Mbps
– SAE J2284-5: High-Speed CAN (HSC) for Vehicle Applications at 500 kbps with CAN FD Data at 5 Mbps
EMC Requirements
– IEC 62228-3 EMC evaluation of transceivers - CAN transceivers
– VeLIO (Vehicle LAN Interoperability and Optimization) CAN and CAN-FD Transceiver Requirements
– SAE J2962-2 Communication Transceivers Qualification Requirements – CAN
•
•
Conformance test requirements:
– ISO 16845-2 Road vehicles – Controller area network (CAN) conformance test plan Part 2: High-speed
medium access unit conformance test plan
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
9.2 Functional Block Diagram
Figure 9-1. Block Diagram
9.3 Feature Description
9.3.1 Pin Description
9.3.1.1 TXD
The TXD input is a logic-level signal, referenced to either VCC or VIO from a CAN controller to the transceiver.
9.3.1.2 GND
GND is the ground pin of the transceiver. The pin must be connected to the PCB ground.
9.3.1.3 VCC
VCC provides the 5-V power supply to the CAN transceiver.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
9.3.1.4 RXD
RXD is the logic-level signal, referenced to either VCC or VIO, from the TCAN1044A-Q1 to a CAN controller. This
pin is only driven once VIO is present.
9.3.1.5 VIO
The VIO pin provides the digital I/O voltage to match the CAN controller voltage thus avoiding the requirement for
a level shifter. It supports voltages from 1.7 V to 5.5 V providing the widest range of controller support.
9.3.1.6 CANH and CANL
The CANH and CANL pins are the CAN high and CAN low differential bus pins. These pins are internally
connected to the CAN transmitter, receiver and the low-power wake-up receiver.
9.3.1.7 STB (Standby)
The STB pin is an input pin used for mode control of the transceiver. The STB pin can be supplied from either
the system processor or from a static system voltage source. If normal mode is the only intended mode of
operation, the STB pin can be tied directly to GND.
9.3.2 CAN Bus States
The CAN bus has two logical states during operation: recessive and dominant. See Figure 9-2 and Figure 9-3.
A dominant bus state occurs when the bus is driven differentially and corresponds to a logic low on the TXD and
RXD pins. A recessive bus state occurs when the bus is biased to VCC/2 via the high-resistance internal input
resistors (RIN) of the receiver and corresponds to a logic high on the TXD and RXD pins.
A dominant state overwrites the recessive state during arbitration. Multiple CAN nodes may be transmitting a
dominant bit at the same time during arbitration, and in this case the differential voltage of the bus is greater than
the differential voltage of a single driver.
The TCAN1044A(V)-Q1 transceiver implements a low-power standby (STB) mode which enables a third bus
state where the bus pins are weakly biased to ground via the high resistance internal resistors of the receiver.
See Figure 9-2 and Figure 9-3.
Normal Mode
Standby Mode
CANH
VDIFF
VDIFF
CANL
Recessive
Dominant
Recessive
Time, t
Figure 9-2. Bus States
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
CANH
2.5V
GND
A
B
RXD
Bias
Unit
CANL
A. A - Normal Mode B - Standby Mode
Figure 9-3. Simplified Recessive Common Mode Bias Unit and Receiver
9.3.3 TXD Dominant Timeout (DTO)
During normal mode, the only mode where the CAN driver is active, the TXD DTO circuit prevents the local node
from blocking network communication in the event of a hardware or software failure where TXD is held dominant
longer than the timeout period tTXD_DTO. The TXD DTO circuit is triggered by a falling edge on TXD. If no rising
edge is seen before the timeout period of the circuit, tTXD_DTO, the CAN driver is disabled. This frees the bus for
communication between other nodes on the network. The CAN driver is reactivated when a recessive signal is
seen on the TXD pin, thus clearing the dominant time out. The receiver remains active and biased to VCC/2 and
the RXD output reflects the activity on the CAN bus during the TXD DTO fault.
The minimum dominant TXD time allowed by the TXD DTO circuit limits the minimum possible transmitted data
rate of the device. The CAN protocol allows a maximum of eleven successive dominant bits (on TXD) for the
worst case, where five successive dominant bits are followed immediately by an error frame. The minimum
transmitted data rate may be calculated using Equation 1.
Minimum Data Rate = 11 bits / tTXD_DTO = 11 bits / 1.2 ms = 9.2 kbps
(1)
Fault is repaired & transmission capability
restored
TXD fault stuck dominant: example PCB failure or bad software
tTXD_DTO
TXD (driver)
Driver disabled freeing bus for other nodes
Normal CAN communication
Bus would be —stuck dominant“ blocking communication for the whole network but TXD DTO
prevents this and frees the bus for communication after the time tTXD_DTO
.
CAN Bus Signal
tTXD_DTO
Communication from other bus node(s)
Communication from repaired node
RXD (receiver)
Communication from local node
Communication from other bus node(s)
Communication from repaired local node
Figure 9-4. Example Timing Diagram for TXD Dominant Timeout
9.3.4 CAN Bus short-circuit current limiting
The TCAN1044A(V)-Q1 has several protection features that limit the short-circuit current when a CAN bus line
is shorted. These include CAN driver current limiting in the dominant and recessive states and TXD dominant
state timeout which prevents permanently having the higher short-circuit current of a dominant state in case of
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
a system fault. During CAN communication the bus switches between the dominant and recessive states, thus
the short-circuit current may be viewed as either the current during each bus state or as a DC average current.
When selecting termination resistors or a common-mode choke for the CAN design the average power rating,
IOS(AVG), should be used. The percentage dominant is limited by the TXD DTO and the CAN protocol which has
forced state changes and recessive bits due to bit stuffing, control fields, and interframe space. These ensure
there is a minimum amount of recessive time on the bus even if the data field contains a high percentage of
dominant bits.
The average short-circuit current of the bus depends on the ratio of recessive to dominant bits and their
respective short-circuit currents. The average short-circuit current may be calculated using Equation 2.
IOS(AVG) = % Transmit x [(% REC_Bits x IOS(SS)_REC) + (% DOM_Bits x IOS(SS)_DOM)] + [% Receive x IOS(SS)_REC
]
(2)
Where:
•
•
•
•
•
•
•
IOS(AVG) is the average short-circuit current
% Transmit is the percentage the node is transmitting CAN messages
% Receive is the percentage the node is receiving CAN messages
% REC_Bits is the percentage of recessive bits in the transmitted CAN messages
% DOM_Bits is the percentage of dominant bits in the transmitted CAN messages
IOS(SS)_REC is the recessive steady state short-circuit current
IOS(SS)_DOM is the dominant steady state short-circuit current
This short circuit current and the possible fault cases of the network should be taken into consideration when
sizing the power supply used to generate the transceivers VCC supply.
9.3.5 Thermal Shutdown (TSD)
If the junction temperature of the TCAN1044A(V)-Q1 exceeds the thermal shutdown threshold, TTSD, the device
turns off the CAN driver circuitry and blocks the TXD to bus transmission path. The shutdown condition is
cleared when the junction temperature of the device drops below TTSD. The CAN bus pins are biased to VCC/2
during a TSD fault and the receiver to RXD path remains operational. The TCAN1044A(V)-Q1 TSD circuit
includes hysteresis which prevents the CAN driver output from oscillating during a TSD fault.
9.3.6 Undervoltage Lockout
The supply pins, VCC and VIO, have undervoltage detection that places the device into a protected state. This
protects the bus during an undervoltage event on either supply pin.
Table 9-1. Undervoltage Lockout - TCAN1044A-Q1
VCC
DEVICE STATE
BUS
RXD PIN
Mirrors bus
> UVVCC
< UVVCC
Normal
Per TXD
Protected
High impedance
High impedance
Table 9-2. Undervoltage Lockout - TCAN1044AV-Q1
VCC
VIO
DEVICE STATE
BUS
RXD PIN
> UVVCC
< UVVCC
> UVVIO
> UVVIO
Normal
Per TXD
Mirrors bus
STB = High: Standby Mode
Weak biased to GND
VIO: Remote wake request
See Remote Wake Request via
Wake-Up Pattern (WUP) in Standby
Mode
STB =Low: Protected Mode
Protected
High impedance
High impedance
High impedance
Recessive
> UVVCC
< UVVCC
< UVVIO
< UVVIO
High impedance
High impedance
Protected
Once the undervoltage condition is cleared and tMODE has expired the TCAN1044A-Q1 will transition to normal
mode and the host controller can send and receive CAN traffic again
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
9.3.7 Unpowered Device
The TCAN1044A(V)-Q1 is designed to be an ideal passive or no load to the CAN bus if the device is unpowered.
The bus pins were designed to have low leakage currents when the device is unpowered, so they do not load
the bus. This is critical if some nodes of the network are unpowered while the rest of the of network remains
operational.
The logic pins also have low leakage currents when the device is unpowered, so they do not load other circuits
which may remain powered.
9.3.8 Floating pins
The TCAN1044A(V)-Q1 has internal pull-ups on critical pins which place the device into known states if the
pin floats. This internal bias should not be relied upon by design though, especially in noisy environments, but
instead should be considered a failsafe protection feature.
When a CAN controller supporting open-drain outputs is used an adequate external pull-up resistor must be
chosen. This ensures that the TXD output of the CAN controller maintains acceptable bit time to the input of the
CAN transceiver. See Table 9-3 for details on pin bias conditions.
Table 9-3. Pin Bias
Pin
Pull-up or Pull-down
Comment
Weakly biases TXD towards recessive to prevent bus blockage or
TXD DTO triggering
TXD
Pull-up
Weakly biases STB towards low-power standby mode to prevent
excessive system power
STB
Pull-up
9.4 Device Functional Modes
9.4.1 Operating Modes
The TCAN1044A(V)-Q1 has two main operating modes; normal mode and standby mode. Operating mode
selection is made by applying a high or low level to the STB pin.
Table 9-4. Operating Modes
STB
High
Low
Device Mode
Driver
Disabled
Enabled
Receiver
RXD Pin
High (recessive) until valid WUP
is received
See Remote Wake Request
via Wake-Up Pattern (WUP) in
Standby Mode
Low current standby mode with
bus wake-up
Low-power receiver and bus
monitor enable
Normal Mode
Enabled
Mirrors bus state
9.4.2 Normal Mode
This is the normal operating mode of the TCAN1044A(V)-Q1. The CAN driver and receiver are fully operational
and CAN communication is bi-directional.
The driver is translating a digital input on the TXD input to a differential output on the CANH and CANL bus pins.
The receiver is translating the differential signal from CANH and CANL to a digital output on the RXD output.
9.4.3 Standby Mode
This is the low-power mode of the TCAN1044A(V)-Q1. The CAN driver and main receiver are switched off and
bi-directional CAN communication is not possible. The low-power receiver and bus monitor circuits are enabled
to allow for RXD wake-up requests via the CAN bus. A wake-up request is output to RXD as shown in Figure
9-5. The local CAN protocol controller should monitor RXD for transitions (high-to-low) and reactivate the device
to normal mode by pulling the STB pin low. The CAN bus pins are weakly pulled to GND in this mode; see
Figure 9-2 and Figure 9-3.
In standby mode, only the VIO supply is required therefore the VCC may be switched off for additional system
level current savings.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
9.4.3.1 Remote Wake Request via Wake-Up Pattern (WUP) in Standby Mode
The TCAN1044A(V)-Q1 supports a remote wake-up request that is used to indicate to the host controller that the
bus is active and the node should return to normal operation.
The device uses the multiple filtered dominant wake-up pattern (WUP) from the ISO 11898-2:2016 standard to
qualify bus activity. Once a valid WUP has been received, the wake request is indicated to the controller by a
falling edge and low period corresponding to a filtered dominant on the RXD output of the TCAN1044A(V)-Q1.
The WUP consists of a filtered dominant pulse, followed by a filtered recessive pulse, and finally by a second
filtered dominant pulse. The first filtered dominant initiates the WUP, and the bus monitor then waits on a filtered
recessive; other bus traffic does not reset the bus monitor. Once a filtered recessive is received the bus monitor
is waiting for a filtered dominant and again, other bus traffic does not reset the bus monitor. Immediately upon
reception of the second filtered dominant the bus monitor recognizes the WUP and drives the RXD output low
every time an additional filtered dominant signal is received from the bus.
For a dominant or recessive to be considered filtered, the bus must be in that state for more than the
tWK_FILTER time. Due to variability in tWK_FILTER the following scenarios are applicable. Bus state times less than
tWK_FILTER(MIN) are never detected as part of a WUP and thus no wake request is generated. Bus state times
between tWK_FILTER(MIN) and tWK_FILTER(MAX) may be detected as part of a WUP and a wake-up request may be
generated. Bus state times greater than tWK_FILTER(MAX) are always detected as part of a WUP, and thus a wake
request is always generated. See Figure 9-5 for the timing diagram of the wake-up pattern.
The pattern and tWK_FILTER time used for the WUP prevents noise and bus stuck dominant faults from causing
false wake-up requests while allowing any valid message to initiate a wake-up request.
The ISO 11898-2:2016 standard has defined times for a short and long wake-up filter time. The tWK_FILTER timing
for the device has been picked to be within the minimum and maximum values of both filter ranges. This timing
has been chosen such that a single bit time at 500 kbps, or two back-to-back bit times at 1 Mbps triggers the
filter in either bus state. Any CAN frame at 500 kbps or less would contain a valid WUP.
For an additional layer of robustness and to prevent false wake-ups, the device implements a wake-up timeout
feature. For a remote wake-up event to successfully occur, the entire WUP must be received within the timeout
value t ≤ tWK_TIMEOUT. If not, the internal logic is reset and the transceiver remains in its current state without
waking up. The full pattern must then be transmitted again, conforming to the constraints mentioned in this
section. See Figure 9-5 for the timing diagram of the wake-up pattern with wake timeout feature.
Bus Wake via RXD
Wake Up Pattern (WUP) received in t < tWK_Timeout
Request
Filtered
Dominant
Filtered
Dominant
Filtered
Recessive
Waiting for
Filtered
Dominant
Waiting for
Filtered
Recessive
Bus
Bus VDiff
RXD
≥ tWK_FILTER
≥ tWK_FILTER
≥ tWK_FILTER
≥ tWK_FILTER
Filtered Dominant RXD Output
Bus Wake Via RXD Requests
Figure 9-5. Wake-Up Pattern (WUP) with tWK_TIMEOUT
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
9.4.4 Driver and Receiver Function
The TCAN1044A-Q1 logic I/Os support CMOS levels with respect to either VCC for 5-V systems (TCAN1044A-
Q1) or VIO for compatibility with MCUs that support 1.8-V, 2.5-V, 3.3-V, or 5-V systems (TCAN1044AV-Q1).
Table 9-5. Driver Function Table
Bus Outputs
Device Mode
TXD Input(1)
Driven Bus State(2)
CANH
High
CANL
Low
Low
High or open
X
Dominant
Normal
High impedance
High impedance
High impedance
High impedance
Biased recessive
Biased to ground
Standby
(1) X = irrelevant
(2) For bus state and bias see Figure 9-2 and Figure 9-3
Table 9-6. Receiver Function Table Normal and Standby Mode
Device Mode
CAN Differential Inputs VID = VCANH – VCANL
Bus State
Dominant
Undefined
Recessive
RXD Pin
Low
VID ≥ 0.9 V
0.5 V < VID < 0.9 V
VID ≤ 0.5 V
Undefined
High
Normal
VID ≥ 1.15 V
0.4 V < VID < 1.15 V
VID ≤ 0.4 V
Dominant
Undefined
Recessive
Open
High
Low if a remote wake event
occurred
Standby
Any
See Figure 9-5
Open (VID ≈ 0 V)
High
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
10 Application Information Disclaimer
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
10.1 Application Information
10.2 Typical Application
The TCAN1044A(V)-Q1 transceiver can be used in applications with a host controller or FPGA that includes the
link layer portion of the CAN protocol. Figure 10-1 shows a typical configuration for 5-V controller applications.
The bus termination is shown for illustrative purposes.
VOUT
VIN
VIN
5-V Voltage
Regulator
3
5
VCC
NC
VDD
7
CANH
8
STB
MCU
TCAN1044A
4
1
CAN FD
RXD
TXD
6
Controller
CANL
GND
Optional: Optional: Filtering,
Terminating Node Transient and ESD
Figure 10-1. Transceiver Application Using 5-V IO Connections
10.2.1 Design Requirements
10.2.1.1 CAN Termination
Termination may be a single 120-Ω resistor at each end of the bus, either on the cable or in a terminating node.
If filtering and stabilization of the common-mode voltage of the bus is desired then split termination may be used,
see Figure 10-2. Split termination improves the electromagnetic emissions behavior of the network by filtering
higher-frequency common-mode noise that may be present on the differential signal lines.
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
Standard Termination
Split Termination
CANH
CANH
RTERM/2
RTERM
TCAN Transceiver
TCAN Transceiver
CSPLIT
RTERM/2
CANL
CANL
Figure 10-2. CAN Bus Termination Concepts
10.2.2 Detailed Design Procedures
10.2.2.1 Bus Loading, Length and Number of Nodes
A typical CAN application may have a maximum bus length of 40 meters and maximum stub length of 0.3 m.
However, with careful design, users can have longer cables, longer stub lengths, and many more nodes to a
bus. A high number of nodes requires a transceiver with high input impedance such as the TCAN1044A(V)-Q1
Many CAN organizations and standards have scaled the use of CAN for applications outside the original ISO
11898-2 standard. They made system level trade off decisions for data rate, cable length, and parasitic loading
of the bus. Examples of these CAN systems level specifications are ARINC 825, CANopen, DeviceNet, SAE
J2284, SAE J1939, and NMEA 2000.
A CAN network system design is a series of tradeoffs. In the ISO 11898-2:2016 specification the driver
differential output is specified with a bus load that can range from 50 Ω to 65 Ω where the differential output
must be greater than 1.5 V. The TCAN1044A(V)-Q1 family is specified to meet the 1.5-V requirement down
to 50 Ω and is specified to meet 1.4-V differential output at 45-Ω bus load. The differential input resistance of
the TCAN1044A(V)-Q1 is a minimum of 40 kΩ. If 100 TCAN1044A(V)-Q1 transceivers are in parallel on a bus,
this is equivalent to a 400-Ω differential load in parallel with the nominal 60-Ω bus termination which gives a
total bus load of approximately 52 Ω. Therefore, the TCAN1044A(V)-Q1 family theoretically supports over 100
transceivers on a single bus segment. However, for a CAN network design margin must be given for signal
loss across the system and cabling, parasitic loadings, timing, network imbalances, ground offsets, and signal
integrity thus a practical maximum number of nodes is often lower. Bus length may also be extended beyond
40 meters by careful system design and data rate tradeoffs. For example, CANopen network design guidelines
allow the network to be up to 1 km with changes in the termination resistance, cabling, less than 64 nodes and
significantly lowered data rate.
This flexibility in CAN network design is one of the key strengths of the various extensions and additional
standards that have been built on the original ISO 11898-2 CAN standard. However, when using this flexibility
the CAN network system designer must take the responsibility of good network design to ensure robust network
operation.
Please refer to the application report SLLA270: Controller Area Network Physical layer requirements. This
document discusses in detail all system design physical layer parameters.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
Node 1
Node 2
Node 3
Node n
(with termination)
System Controller
System Controller
System Controller
System Controller
CAN FD
Controller
CAN FD
Controller
CAN FD
Controller
CAN FD
Controller
TCAN1043-Q1
RTERM
TCAN1044AV-Q1
TCAN1044A-Q1
TCAN1044A-Q1
Figure 10-3. Typical CAN Bus
10.3 System Examples
The TCAN1044AV-Q1 CAN transceiver is typically used in applications with a host controller or FPGA that
includes the link layer portion of the CAN protocol. A 1.8-V, 2.5-V, or 3.3-V application is shown in Figure 10-4.
The bus termination is shown for illustrative purposes.
VBAT
VOUT
VIN
5-V Voltage
Regulator
3
VCC
VDD
7
CANH
8
STB
MCU
TCAN1044AV
4
1
VIN
CAN FD
RXD
TXD
6
Controller
CANL
VIO
GND
1.8 V / 2.5 V / 3.3 V
Regulator
5
VOUT
Optional:
Terminating Node
Optional: Filtering,
Transient and ESD
Figure 10-4. Typical Transceiver Application Using 1.8-V, 2.5-V, 3.3-V IO Connections
11 Power Supply Recommendations
The TCAN1044A-Q1 transceiver is designed to operate with a main VCC input voltage supply range between 4.5
V and 5.5 V.
The TCAN1044AV-Q1 implements an IO level shifting supply input, VIO, designed for a range between 1.8 V and
5.5 V.
Both the VCC and VIO inputs must be well regulated. In addition to the power supply filtering a decoupling
capacitance, typically 100 nF, should be placed near the CAN transceiver's main VCC and VIO supply pins.
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
12 Layout
Robust and reliable CAN node design may require special layout techniques depending on the application
and design requirements. Since transient disturbances have high frequency content and a wide bandwidth,
high-frequency layout techniques should be applied during PCB design.
12.1 Layout Guidelines
•
Place the protection and filtering circuitry close to the bus connector, J1, to prevent transients, ESD, and
noise from propagating onto the board. This layout example shows a optional transient voltage suppression
(TVS) diode, D1, which may be implemented if the system-level requirements exceed the specified rating of
the transceiver. This example also shows optional bus filter capacitors C4 and C5.
Design the bus protection components in the direction of the signal path. Do not force the transient current to
divert from the signal path to reach the protection device.
•
•
•
Decoupling capacitors should be placed as close as possible to the supply pins VCC and VIO of transceiver.
Use at least two vias for supply and ground connections of bypass capacitors and protection devices to
minimize trace and via inductance.
Note
High-frequency current follows the path of least impedance and not the path of least resistance.
•
This layout example shows how split termination could be implemented on the CAN node. The termination
is split into two resistors, R2 and R3, with the center or split tap of the termination connected to ground via
capacitor C3. Split termination provides common mode filtering for the bus. See Section 10.2.1.1, Section
9.3.4, and Equation 2 for information on termination concepts and power ratings needed for the termination
resistor(s).
12.2 Layout Example
µC V
R1
TXD
STB
C4
STB
R2
R3
GND
CANH
CANL
VIO
GND
C3
GND
Choke
C1
D1
J1
VCC
VCC
RXD
µC V
C2
C5
Figure 12-1. Layout Example
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
TCAN1044A-Q1, TCAN1044AV-Q1
SLLSFJ3C – FEBRUARY 2021 – REVISED DECEMBER 2021
www.ti.com
13 Device and Documentation Support
13.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
13.2 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
13.3 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
13.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
13.5 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: TCAN1044A-Q1 TCAN1044AV-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Dec-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
PTCAN1044AVDDFRQ1
PTCAN1044AVDRQ1
TCAN1044ADDFRQ1
TCAN1044ADRBRQ1
TCAN1044ADRQ1
ACTIVE SOT-23-THIN
DDF
D
8
8
8
8
8
8
8
8
3000
2500
TBD
TBD
Call TI
Call TI
-40 to 150
-40 to 150
-40 to 150
-40 to 150
-40 to 150
-40 to 150
-40 to 150
-40 to 150
ACTIVE
SOIC
Call TI
Call TI
ACTIVE SOT-23-THIN
DDF
DRB
D
3000 RoHS & Green
3000 RoHS & Green
2500 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
2500 RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
2HGF
ACTIVE
ACTIVE
SON
1044A
1044A
2HHF
SOIC
TCAN1044AVDDFRQ1
TCAN1044AVDRBRQ1
TCAN1044AVDRQ1
ACTIVE SOT-23-THIN
DDF
DRB
D
ACTIVE
ACTIVE
SON
1044AV
1044AV
SOIC
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Dec-2021
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Dec-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TCAN1044ADDFRQ1
SOT-
DDF
8
3000
180.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
23-THIN
TCAN1044ADRBRQ1
TCAN1044ADRQ1
SON
DRB
D
8
8
8
3000
2500
3000
330.0
330.0
180.0
12.4
12.4
8.4
3.3
6.4
3.2
3.3
5.2
3.2
1.1
2.1
1.4
8.0
8.0
4.0
12.0
12.0
8.0
Q1
Q1
Q3
SOIC
TCAN1044AVDDFRQ1
SOT-
DDF
23-THIN
TCAN1044AVDRBRQ1
TCAN1044AVDRQ1
SON
DRB
D
8
8
3000
2500
330.0
330.0
12.4
12.4
3.3
6.4
3.3
5.2
1.1
2.1
8.0
8.0
12.0
12.0
Q1
Q1
SOIC
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Dec-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TCAN1044ADDFRQ1
TCAN1044ADRBRQ1
TCAN1044ADRQ1
SOT-23-THIN
SON
DDF
DRB
D
8
8
8
8
8
8
3000
3000
2500
3000
3000
2500
210.0
367.0
853.0
210.0
367.0
853.0
185.0
367.0
449.0
185.0
367.0
449.0
35.0
35.0
35.0
35.0
35.0
35.0
SOIC
TCAN1044AVDDFRQ1
TCAN1044AVDRBRQ1
TCAN1044AVDRQ1
SOT-23-THIN
SON
DDF
DRB
D
SOIC
Pack Materials-Page 2
PACKAGE OUTLINE
VSON - 1 mm max height
DRB0008J
PLASTIC QUAD FLAT PACK- NO LEAD
3.1
2.9
B
A
PIN 1 INDEX AREA
3.1
2.9
0.1 MIN
(0.13)
SECTION A-A
TYPICAL
1 MAX
C
SEATING PLANE
0.08 C
0.05
0.00
1.75
1.55
(0.2) TYP
6X 0.65
(0.19)
4
5
SYMM
9
2.5
2.3
1.95
1
8
0.36
0.26
8X
PIN 1 ID
(OPTIONAL)
0.1
0.05
C A B
C
SYMM
0.5
0.3
8X
4225036/A 06/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for optimal thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
VSON - 1 mm max height
DRB0008J
PLASTIC QUAD FLAT PACK- NO LEAD
(2.8)
(1.65)
8X (0.6)
8X (0.31)
SYMM
1
8
6X (0.65)
SYMM
9
(1.95) (2.4)
(0.95)
(R0.05) TYP
4
5
(Ø 0.2) VIA
TYP
(0.575)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 20X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
METAL
SOLDER MASK
OPENING
EXPOSED METAL
EXPOSED METAL
SOLDER MASK
OPENING
METAL
NON- SOLDER MASK
SOLDER MASK
DEFINED
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4225036/A 06/2019
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
VSON - 1 mm max height
DRB0008J
PLASTIC QUAD FLAT PACK- NO LEAD
(2.8)
2X
(1.51)
8X (0.6)
8X (0.31)
SYMM
1
8
2X
(1.06)
6X (0.65)
SYMM
(1.95)
(0.63)
9
(R0.05) TYP
4
5
METAL
TYP
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD
81% PRINTED COVERAGE BY AREA
SCALE: 20X
4225036/A 06/2019
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OUTLINE
DDF0008A
SOT-23 - 1.1 mm max height
S
C
A
L
E
4
.
0
0
0
PLASTIC SMALL OUTLINE
C
2.95
2.65
SEATING PLANE
TYP
PIN 1 ID
AREA
0.1 C
A
6X 0.65
8
1
2.95
2.85
NOTE 3
2X
1.95
4
5
0.4
0.2
8X
0.1
C A
B
1.65
1.55
B
1.1 MAX
0.20
0.08
TYP
SEE DETAIL A
0.25
GAGE PLANE
0.1
0.0
0 - 8
0.6
0.3
DETAIL A
TYPICAL
4222047/B 11/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
www.ti.com
EXAMPLE BOARD LAYOUT
DDF0008A
SOT-23 - 1.1 mm max height
PLASTIC SMALL OUTLINE
8X (1.05)
SYMM
1
8
8X (0.45)
SYMM
6X (0.65)
5
4
(R0.05)
TYP
(2.6)
LAND PATTERN EXAMPLE
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4222047/B 11/2015
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DDF0008A
SOT-23 - 1.1 mm max height
PLASTIC SMALL OUTLINE
8X (1.05)
SYMM
(R0.05) TYP
8
1
8X (0.45)
SYMM
6X (0.65)
5
4
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4222047/B 11/2015
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
相关型号:
TCAN1044ADRQ1
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode
TI
TCAN1044AV-Q1
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode
TI
TCAN1044AVDDFRQ1
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode
TI
TCAN1044AVDRBRQ1
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode
TI
TCAN1044AVDRQ1
TCAN1044A-Q1 and TCAN1044AV-Q1 Automotive Fault-Protected CAN FD Transceiver with Standby mode
TI
©2020 ICPDF网 联系我们和版权申明