TLC193_14 [TI]
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR;型号: | TLC193_14 |
厂家: | TEXAS INSTRUMENTS |
描述: | DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR |
文件: | 总23页 (文件大小:355K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
D, JG, P, OR PW PACKAGE
Very Low Power . . . 110 µW Typ at 5 V
(TOP VIEW)
Fast Response Time . . . t
With 5-mV Overdrive
= 2.5 µs Typ
PLH
1OUT
1IN–
1IN+
GND
V
DD
1
2
3
4
8
7
6
5
Single Supply Operation:
2OUT
2IN–
2IN+
TLC393C . . . 3 V to 16 V
TLC393I . . . 3 V to 16 V
TLC393Q . . . 4 V to 16 V
TLC393M . . . 4 V to 16 V
TLC193M . . . 4 V to 16 V
FK PACKAGE
(TOP VIEW)
On-Chip ESD Protection
description
The TLC193 and TLC393 consist of dual
independent micropower voltage comparators
designed to operate from a single supply. They
are functionally similar to the LM393 but uses
one-twentieth the power for similar response
times. The open-drain MOS output stage
interfaces to a variety of loads and supplies. For
3
2 1 20 19
NC
18
17
16
15
14
4
5
6
7
8
NC
1IN–
NC
2OUT
NC
1IN+
NC
2IN–
NC
9 10 11 12 13
a
similar device with a push-pull output
configuration (see the TLC3702 data sheet).
Texas Instruments LinCMOS process offers
superior analog performance to standard CMOS
processes. Along with the standard CMOS
advantages of low power without sacrificing
speed, high input impedance, and low bias
NC – No internal connection
symbol (each comparator)
currents, the LinCMOS
process offers ex-
IN+
IN–
tremely stable input offset voltages, even with
differential input stresses of several volts. This
characteristic makes it possible to build reliable
CMOS comparators.
OUT
The TLC393C is characterized for operation over the commercial temperature range of T = 0°C to 70°C. The
A
TLC393I is characterized for operation over the extended industrial temperature range of T = –40°C to 85°C.
A
The TLC393Q is characterized for operation over the full automotive temperature range of T = –40°Cto125°C.
A
The TLC193M and TLC393M are characterized for operation over the full military temperature range of
T = –55°C to 125°C.
A
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright 1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
AVAILABLE OPTIONS
PACKAGES
V
max
IO
T
A
SMALL OUTLINE
(D)
CHIP CARRIER
(FK)
CERAMIC DIP
(JG)
PLASTIC DIP
(P)
TSSOP
(PW)
at 25°C
0°C to 70°C
– 40°C to 85°C
– 40°C to 125°C
– 55°C to 125°C
5 mV
5 mV
5 mV
5 mV
TLC393CD
TLC393ID
TLC393QD
TLC393MD
—
—
TLC393CP
TLC393IP
—
TLC393CPWLE
—
—
—
—
TLC393IPWLE
—
—
TLC193MFK
TLC193MJG
TLC393MP
†
The D package is available taped and reeled. Add the suffix R to the device type (e.g., TLC393CDR).
schematic
OUT
OPEN-DRAIN CMOS OUTPUT
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 18 V
DD
Differential input voltage, V (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
ID
Input voltage range, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to V
I
DD
Output voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 16 V
O
Input current, I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5 mA
I
Output current, I (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
O
Total supply current into V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
DD
Total current out of GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range: TLC393C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
TLC393I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
TLC393Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
TLC393M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
TLC193M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or P package . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to network ground.
2. Differential voltages are at IN+ with respect to IN–.
DISSIPATION RATING TABLE
T
≤ 25°C
DERATING FACTOR
T
= 70°C
T
= 85°C
T = 125°C
A
POWER RATING
A
A
A
PACKAGE
POWER RATING
ABOVE T = 25°C
POWER RATING
POWER RATING
A
D
FK
JG
P
725 mW
5.8 mW/°C
11.0 mW/°C
8.4 mW/°C
8.0 mW/°C
4.2 mW/°C
464 mW
377 mW
145 mW
275 mW
210 mW
—
1375 mW
1050 mW
1000 mW
525 mW
880 mW
715 mW
672 mW
546 mW
640 mW
520 mW
PW
336 mW
273 mW
—
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
recommended operating conditions
TLC393C
UNIT
MIN NOM
MAX
Supply voltage, V
DD
Common-mode input voltage, V
3
5
16
V
V
–0.2
V
– 1.5
IC
DD
Low-level output current, I
OL
20
70
mA
°C
Operating free-air temperature, T
0
A
electrical characteristics at specified operating free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC393C
UNIT
†
PARAMETER
T
A
TEST CONDITIONS
MIN
TYP MAX
V
V
= V
min,
25°C
1.4
5
IC
ICR
= 5 V to 10 V,
V
IO
Input offset voltage
mV
DD
0°C to 70°C
6.5
See Note 3
25°C
70°C
1
5
pA
nA
pA
nA
I
I
Input offset current
V
= 2.5 V
= 2.5 V
IO
IC
IC
0.3
0.6
25°C
Input bias current
V
IB
70°C
25°C
0 to V
– 1
DD
0 to V – 1.5
DD
V
Common-mode input voltage range
V
ICR
0°C to 70°C
25°C
84
84
CMMR Common-mode rejection ratio
V
V
= V
min
ICR
70°C
dB
IC
0°C
84
25°C
85
k
Supply-voltage rejection ratio
= 5 V to 10 V
70°C
85
dB
SVR
DD
0°C
85
25°C
300
400
650
40
1
V
Low-level output voltage
V
V
= –1 V,
I
OL
= 6 mA
= 5 V
mV
OL
OH
DD
ID
70°C
25°C
0.8
22
nA
I
I
High-level output current
= 1 V,
V
O
ID
70°C
µA
25°C
40
50
Supply current (both comparators)
Outputs low, No load
µA
0°C to 70°C
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 3: The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
recommended operating conditions
TLC393I
MIN NOM
UNIT
MAX
Supply voltage, V
DD
Common-mode input voltage, V
3
5
16
V
V
– 0.2
V
– 1.5
IC
DD
Low-level output current, I
OL
20
85
mA
°C
Operating free-air temperature, T
– 40
A
electrical characteristics at specified operating free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC393I
UNIT
†
PARAMETER
T
A
TEST CONDITIONS
MIN
TYP
MAX
V
V
= V
min,
25°C
1.4
5
IC
ICR
= 5 V to 10 V,
V
IO
Input offset voltage
mV
DD
–40°C to 85°C
7
See Note 3
25°C
85°C
1
5
pA
nA
pA
nA
I
I
Input offset current
V
= 2.5 V
= 2.5 V
IO
IC
IC
1
2
25°C
Input bias current
V
IB
85°C
25°C
0 to V
– 1
DD
– 1.5
V
Common-mode input voltage range
V
ICR
–40°C to 85°C 0 to V
25°C
DD
84
84
CMMR Common-mode rejection ratio
V
V
= V
min
ICR
85°C
dB
IC
– 40°C
25°C
84
85
k
Supply-voltage rejection ratio
= 5 V to 10 V
85°C
85
dB
SVR
DD
– 40°C
25°C
84
300
400
700
40
1
V
Low-level output voltage
V
V
= –1 V,
I
OL
= 6 mA
= 5 V
mV
OL
OH
DD
ID
85°C
25°C
0.8
22
nA
I
I
High-level output current
= 1 V,
V
O
ID
85°C
µA
25°C
40
65
Supply current (both comparators)
Outputs low, No load
µA
–40°C to 85°C
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 3: The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
recommended operating conditions
TLC393Q
UNIT
MIN NOM
MAX
Supply voltage, V
DD
Common-mode input voltage, V
4
0
5
16
V
V
V
– 1.5
IC
DD
Low-level output current, I
OL
20
mA
°C
Operating free-air temperature, T
–40
125
A
electrical characteristics at specified operating free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC393Q
UNIT
†
PARAMETER
T
A
TEST CONDITIONS
MIN
TYP
MAX
V
V
= V
min,
25°C
1.4
5
IC
ICR
= 5 V to 10 V,
V
IO
Input offset voltage
mV
DD
–40°C to 125°C
10
See Note 4
25°C
125°C
1
5
pA
nA
pA
nA
I
I
Input offset current
V
= 2.5 V
= 2.5 V
IO
IC
IC
15
30
25°C
Input bias current
V
IB
125°C
25°C
0 to V
– 1
DD
– 1.5
V
Common-mode input voltage range
V
ICR
–40°C to 125°C 0 to V
25°C
DD
84
84
CMMR Common-mode rejection ratio
V
V
= V
min
ICR
125°C
dB
IC
–40°C
84
25°C
85
k
Supply-voltage rejection ratio
= 5 V to 10 V
125°C
84
dB
SVR
DD
–40°C
84
25°C
300
400
800
40
1
V
Low-level output voltage
V
V
= –1 V,
I
OL
= 6 mA
= 5 V
mV
OL
OH
DD
ID
125°C
25°C
0.8
22
nA
I
I
High-level output current
= 1 V,
V
O
ID
125°C
µA
25°C
40
90
Supply current (both comparators)
Outputs low, No load
µA
–40°C to 125°C
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 4: The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V (with a 2.5-kΩ load to
).
V
DD
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
recommended operating conditions
TLC193M, TLC393M
UNIT
MIN NOM
MAX
Supply voltage, V
DD
Common-mode input voltage, V
4
0
5
16
V
V
V
– 1.5
IC
DD
Low-level output current, I
OL
20
mA
°C
Operating free-air temperature, T
–55
125
A
electrical characteristics at specified operating free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC193M, TLC393M
†
PARAMETER
T
A
UNIT
TEST CONDITIONS
MIN
TYP
MAX
V
V
= V
min,
25°C
1.4
5
IC
ICR
= 5 V to 10 V,
V
IO
Input offset voltage
mV
DD
–55°C to 125°C
10
See Note 4
25°C
125°C
1
5
pA
nA
pA
nA
I
I
Input offset current
V
= 2.5 V
= 2.5 V
IO
IC
IC
15
30
25°C
Input bias current
V
IB
125°C
25°C
0 to V
– 1
DD
– 1.5
V
Common-mode input voltage range
V
ICR
–55°C to 125°C 0 to V
25°C
DD
84
84
CMMR Common-mode rejection ratio
V
V
= V
min
ICR
125°C
dB
IC
–55°C
84
25°C
85
k
Supply-voltage rejection ratio
= 5 V to 10 V
125°C
84
dB
SVR
DD
–55°C
84
25°C
300
400
800
40
1
V
Low-level output voltage
V
V
= –1 V,
I
OL
= 6 mA
= 5 V
mV
OL
OH
DD
ID
125°C
25°C
0.8
22
nA
I
I
High-level output current
= 1 V,
V
O
ID
125°C
µA
25°C
40
90
Supply current (both comparators)
Outputs low, No load
µA
–55°C to 125°C
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 4: The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V (with a 2.5-kΩ load to
).
V
DD
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
switching characteristics, V
= 5 V, T = 25°C (see Figure 3)
A
DD
TLC393C, TLC393I
TLC393Q, TLC193M,
TLC393M
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
4.5
MAX
Overdrive = 2 mV
Overdrive = 5 mV
Overdrive = 10 mV
Overdrive = 20 mV
Overdrive = 40 mV
2.5
f = 10 kHz,
= 15 pF
t
Propagation delay time, low-to-high-level output
1.7
µs
PLH
C
L
1.2
1.1
V = 1.4-V step at IN+
I
1.1
Overdrive = 2 mV
3.6
Overdrive = 5 mV
Overdrive = 10 mV
Overdrive = 20 mV
Overdrive = 40 mV
2.1
f = 10 kHz,
= 15 pF
t
t
Propagation delay time, high-to-low-level output
1.3
µs
PHL
C
L
0.85
0.55
0.10
V = 1.4-V step at IN+
I
f = 10 kHz,
Fall time, output
Overdrive = 50 mV
22
ns
f
C
= 15 pF
L
PARAMETER MEASUREMENT INFORMATION
The TLC393 contains a digital output stage which, if held in the linear region of the transfer curve, can cause
damage to the device. Conventional operational amplifier/comparator testing incorporates the use of a servo
loop that is designed to force the device output to a level within this linear region. Since the servo-loop method
of testing cannot be used, the following alternatives for testing parameters such as input offset voltage,
common-mode rejection ratio, etc., are suggested.
Toverifythattheinputoffsetvoltagefallswithinthelimitsspecified, thelimitvalueisappliedtotheinputasshown
in Figure 1(a). With the noninverting input positive with respect to the inverting input, the output should be high.
With the input polarity reversed, the output should be low.
A similar test can be made to verify the input offset voltage at the common-mode extremes. The supply voltages
can be slewed as shown in Figure 1(b) for the V
greater accuracy.
test, rather than changing the input voltages, to provide
ICR
5 V
1 V
5.1 kΩ
5.1 kΩ
+
+
–
–
Applied V
Limit
Applied V
Limit
IO
IO
V
O
V
O
– 4 V
(a) V WITH V = 0 V
IO IC
(b) V WITH V = 4 V
IO IC
Figure 1. Method for Verifying That Input Offset Voltage Is Within Specified Limits
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
PARAMETER MEASUREMENT INFORMATION
A close approximation of the input offset voltage can be obtained by using a binary search method to vary the
differential input voltage while monitoring the output state. When the applied input voltage differential is equal,
but opposite in polarity, to the input offset voltage, the output changes states.
Figure 2 illustrates a practical circuit for direct dc measurement of input offset voltage that does not bias the
comparator in the linear region. The circuit consists of a switching-mode servo loop in which U1A generates
a triangular waveform of approximately 20-mV amplitude. U1B acts as a buffer, with C2 and R4 removing any
residual dc offset. The signal is then applied to the inverting input of the comparator under test, while the
noninverting input is driven by the output of the integrator formed by U1C through the voltage divider formed
by R9 and R10. The loop reaches a stable operating point when the output of the comparator under test has
a duty cycle of exactly 50%, which can only occur when the incoming triangle wave is sliced symmetrically or
when the voltage at the noninverting input exactly equals the input offset voltage.
The voltage divider formed by R9 and R10 provides an increase in input offset voltage by a factor of 100 to
make measurement easier. The values of R5, R8, R9, and R10 can significantly influence the accuracy of the
reading; therefore, it is suggested that their tolerance level be 1% or lower.
Measuring the extremely low values of input current requires isolation from all other sources of leakage current
and compensation for the leakage of the test socket and board. With a good picoammeter, the socket and board
leakage can be measured with no device in the socket. Subsequently, this open-socket leakage value can be
subtracted from the measurement obtained with a device in the socket to obtain the actual input current of the
device.
V
DD
C3
0.68 µF
U1B
1/4 TLC274CN
R5
1.8 kΩ, 1%
C2
1 µF
+
Buffer
U1C
R6
–
+
1/4 TLC274CN
5.1 kΩ
–
DUT
–
R4
47 kΩ
R7
1 MΩ
V
IO
(X100)
R1
240 kΩ
+
Integrator
R8
1.8 kΩ, 1%
U1A
1/4 TLC274CN
C4
0.1 µF
–
+
C1
0.1 µF
Triangle
Generator
R9
10 kΩ, 1%
R10
100 Ω, 1%
R2
10 kΩ
R3
100 Ω
Figure 2. Circuit for Input Offset Voltage Measurement
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
PARAMETER MEASUREMENT INFORMATION
Propagationdelaytimeisdefinedastheintervalbetweentheapplicationofaninputstepfunctionandtheinstant
when the output reaches 50% of its maximum value. Propagation delay time, low-to-high-level output, is
measured from the leading edge of the input pulse, while propagation delay time, high-to-low-level output, is
measured from the trailing edge of the input pulse. Propagation delay time measurement at low input signal
levels can be greatly affected by the input offset voltage. The offset voltage should be balanced by the
adjustment at the inverting input (as shown in Figure 3) so that the circuit is just at the transition point. Then a
low signal, for example, 105 mV or 5 mV overdrive, causes the output to change state.
V
DD
1 µF
5.1 kΩ
Pulse
Generator
50 Ω
DUT
1 V
Input Offset Voltage
Compensation
Adjustment
C
10 Ω
10 Turn
L
(see Note A)
1 kΩ
0.1 µF
– 1 V
TEST CIRCUIT
Overdrive
Overdrive
Input
100 mV
Input
100 mV
90%
90%
Low-to-High-
Level Output
High-to-Low-
Level Output
50%
10%
50%
10%
t
r
t
f
t
t
PHL
PLH
VOLTAGE WAVEFORMS
NOTE A: C includes probe and jig capacitance.
L
Figure 3. Propagation Delay, Rise Time, and Fall Time Circuit and Voltage Waveforms
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
V
Input offset voltage
Input bias current
Distribution
4
5
6
7
IO
I
IB
vs Free-air temperature
vs Free-air temperature
vs Free-air temperature
CMRR Common-mode rejection ratio
k
Supply-voltage rejection ratio
SVR
vs Low-level output current
vs Free-air temperature
8
9
V
Low-level output voltage
OL
OH
DD
vs High-level output voltage
vs Free-air temperature
10
11
I
I
Low-level output current
Supply current
vs Supply voltage
vs Free-air temperature
12
13
t
t
Low-to-high level output propagation delay time
High-to-low level output propagation delay time
Low-to-high-level output response
High-to-low level output response
Fall time
vs Supply voltage
14
15
16
17
18
PLH
vs Supply voltage
PHL
Low-to-high level output propagation delay time
High-to-low level output propagation delay time
vs Supply voltage
t
f
INPUT BIAS CURRENT
vs
DISTRIBUTION OF INPUT
†
FREE-AIR TEMPERATURE
†
OFFSET VOLTAGE
10
1
100
90
V
V
T
A
= 5 V
DD
= 2.5 V
V
V
= 5 V
= 2.5 V
DD
IC
IC
= 25°C
80
70
60
50
0.1
40
30
20
10
0.01
0.001
0
25
50
75
100
125
–5 –4 –3 –2 –1
0
1
2
3
4
5
T
A
– Free-Air Temperature – °C
V
IO
– Input Offset Voltage – mV
Figure 4
Figure 5
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
†
TYPICAL CHARACTERISTICS
SUPPLY VOLTAGE REJECTION RATIO
COMMON-MODE REJECTION RATIO
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
90
89
88
87
86
85
84
83
90
89
88
87
86
85
84
83
V
DD
= 5 V to 10 V
V
DD
= 5 V
82
81
80
82
81
80
–75 –50 –25
0
25
50
75
100 125
–75 –50 –25
0
25
50
75
100 125
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 6
Figure 7
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
1.5
600
500
400
V
= 5 V
= 6 mA
T
A
= 25°C
DD
4 V
I
OL
1.25
V
DD
= 3 V
1
5 V
0.75
300
200
10 V
0.5
0.25
100
0
V
= 16 V
DD
0
0
2
4
6
8
10 12 14 16 18
20
–75 –50 –25
0
25
50
75
100 125
I
– Low-Level Output Current – mA
OL
T
A
– Free-Air Temperature – °C
Figure 8
Figure 9
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
†
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
FREE-AIR TEMPERATURE
1000
100
10
1000
100
10
V
DD
= V
= 5 V
OH
T
= 125°C
A
T
= 85°C
= 70°C
A
T
A
T
A
= 25°C
1
1
V
= V
OH
OH
DD
4
0.1
0.1
25
50
75
100
125
0
2
6
8
10
12
14
16
V
– High-Level Output Voltage – V
T
A
– Free-Air Temperature – °C
Figure 10
Figure 11
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
40
35
30
25
20
15
50
V
= 5 V
Outputs Low
No Loads
DD
No Load
T
= – 55°C
A
45
40
35
30
T
= – 40°C
A
T
A
= 25°C
Outputs Low
25
20
T
A
= 85°C
= 125°C
T
A
15
10
5
10
Outputs High
5
0
0
–75 –50 –25
0
25
50
75
100 125
0
2
4
6
8
10
12
14
16
T
A
– Free-Air Temperature – °C
V
DD
– Supply Voltage – V
Figure 12
Figure 13
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
TYPICAL CHARACTERISTICS
LOW-TO-HIGH-LEVEL
OUTPUT RESPONSE TIME
vs
HIGH-TO-LOW-LEVEL
OUTPUT RESPONSE TIME
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
5
6
5
C
R
T
= 15 pF
= 5.1 kΩ (pullup to V
= 25°C
C
R
T
= 15 pF
= 5.1 kΩ (pullup to V
= 25°C
L
L
A
L
L
A
)
4.5
)
DD
DD
4
3.5
3
Overdrive = 2 mV
5 mV
4
3
2
1
0
Overdrive = 2 mV
2.5
5 mV
10 mV
20 mV
2
10 mV
20 mV
1.5
1
40 mV
0.5
0
40 mV
6
0
2
4
6
8
10
12
14
16
0
2
4
8
10
12
14
16
V
DD
– Supply Voltage – V
V
DD
– Supply Voltage – V
Figure 14
Figure 15
HIGH-TO-LOW-LEVEL OUTPUT
PROPAGATION DELAY
LOW-TO-HIGH-LEVEL OUTPUT
PROPAGATION DELAY
FOR VARIOUS INPUT OVERDRIVES
FOR VARIOUS INPUT OVERDRIVES
5
5
40 mV
20 mV
10 mV
5 mV
40 mV
20 mV
10 mV
5 mV
2 mV
2 mV
0
100
0
0
100
0
V
C
R
= 5 V
= 15 pF
= 5.1 kΩ (pullup to V
= 25°C
DD
L
L
)
DD
T
A
V
C
R
= 5 V
= 15 pF
= 5.1 kΩ (pullup to V
= 25°C
DD
L
L
)
DD
T
A
0
1
2
3
4
5
0
1
2
3
4
5
t
– High-to-Low-Level Output
Propagation Delay Time – µs
t
– Low-to-High-Level Output
Propagation Delay Time – µs
PHL
PLH
Figure 16
Figure 17
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
TYPICAL CHARACTERISTICS
OUTPUT FALL TIME
vs
SUPPLY VOLTAGE
60
50
C
= 100 pF
L
40
30
20
50 pF
15 pF
50-mV Overdrive
10
0
R
= 5.1 kΩ (pullup to V
= 25°C
)
DD
L
T
A
0
2
4
6
8
10
12
14
16
V
DD
– Supply Voltage – V
Figure 18
APPLICATION INFORMATION
The input should always remain within the supply rails in order to avoid forward biasing the diodes in the electrostatic
discharge (ESD) protection structure. If either input exceeds this range, the device will not be damaged as long as
the input current is limited to less than 5 mA. To maintain the expected output state, the inputs must remain within
the common-mode range. For example, at 25°C with V
to assure proper device operation.
= 5 V, both inputs must remain between –0.2 V and 4 V
DD
To assure reliable operation, the supply should be decoupled with a capacitor (0.1-µF) positioned as close to the
device as possible.
The TLC393 has internal ESD-protection circuits that prevent functional failures at voltages up to 2000 V as tested
under MIL-STD-883C, Method 3015.2; however, care should be exercised in handling these devices, as exposure
to ESD may result in the degradation of the device parametric performance.
Table of Applications
FIGURE
Pulse-width-modulated motor speed controller
Enhanced supply supervisor
19
20
21
28
Two-phase nonoverlapping clock generator
Micropower switching regulator
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
APPLICATION INFORMATION
12 V
SN75603
Half-H Driver
DIR
EN
12 V
5 V
C2
(see Note A)
5.1 kΩ
100 kΩ
5.1 kΩ
+
–
+
–
10 kΩ
5 V
Motor
10 kΩ
10 kΩ
C1
1/2 TLC393
0.01 µF
(see Note B)
12 V
1/2 TLC393
SN75604
Half-H Driver
DIR
EN
5 V
10 kΩ
Motor Speed Control
Potentiometer
5 V
Direction
Control
S1
SPDT
NOTES: A. The recommended minimum capacitance is 10 µF to eliminate common ground switching noise.
B. Adjust C1 for change in oscillator frequency.
Figure 19. Pulse-Width-Modulated Motor Speed Controller
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
APPLICATION INFORMATION
5 V
12 V
5 V
V
CC
SENSE
3.3 kΩ
10 kΩ
5.1 kΩ
12-V
Sense
+
–
To µP
Reset
TL7705A
RESIN
REF
RESET
GND
1 kΩ
1/2 TLC393
C
T
2.5 V
12 V
C
T
1 µF
(see Note B)
5.1 kΩ
+
–
To µP Interrupt
Early Power Fail
R1
V
UNREG
1/2 TLC393
(see Note A)
R2
Monitors 5-VDC Rail
Monitors 12-VDC Rail
Early Power Fail Warning
(R1 +R2)
NOTES: A. VUNREG
2.5
R2
B. The value of C determines the time delay of reset.
T
Figure 20. Enhanced Supply Supervisor
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
APPLICATION INFORMATION
12 V
12 V
R1
100 Ω
(see Note B)
5.1 kΩ
–
+
12 V
1OUT
R2
5 kΩ
1/2 TLC393
(see Note C)
5.1 kΩ
100 kΩ
–
+
12 V
1/2 TLC393
22 kΩ
5.1 kΩ
C1
–
+
0.01 µF
(see Note A)
2OUT
100 kΩ
100 kΩ
1/2 TLC393
R3
100 kΩ
(see Note B)
12 V
1OUT
2OUT
NOTES: A. Adjust C1 for a change in oscillator frequency where:
1/f = 1.85(100 kΩ)C1
B. Adjust R1 and R3 to change duty cycle
C. Adjust R2 to change deadtime
Figure 21. Two-Phase Nonoverlapping Clock Generator
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.010 (0,25)
M
0.014 (0,35)
14
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°–8°
0.044 (1,12)
A
0.016 (0,40)
Seating Plane
0.004 (0,10)
0.010 (0,25)
0.004 (0,10)
0.069 (1,75) MAX
PINS **
8
14
16
DIM
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MAX
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
A MIN
4040047/D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
MECHANICAL DATA
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
A
B
NO. OF
TERMINALS
**
18 17 16 15 14 13 12
MIN
MAX
MIN
MAX
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
19
20
11
10
9
20
28
44
52
68
84
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
B SQ
22
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
8
A SQ
23
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
7
24
25
6
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
5
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
26 27 28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140/D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
MECHANICAL DATA
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE PACKAGE
0.400 (10,20)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
0.130 (3,30) MIN
Seating Plane
0.063 (1,60)
0.015 (0,38)
0°–15°
0.023 (0,58)
0.015 (0,38)
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.
E. Falls within MIL-STD-1835 GDIP1-T8
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
MECHANICAL DATA
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE PACKAGE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.125 (3,18) MIN
0.100 (2,54)
0°–15°
0.021 (0,53)
0.015 (0,38)
0.010 (0,25)
M
0.010 (0,25) NOM
4040082/B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC193, TLC393
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATOR
SLCS115D – DECEMBER 1986 – REVISED JANUARY 1999
MECHANICAL DATA
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0,30
0,65
M
0,10
0,19
14
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°–8°
0,75
A
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
8
14
16
20
24
28
DIM
3,10
2,90
5,10
4,90
5,10
4,90
6,60
6,40
7,90
7,70
9,80
9,60
A MAX
A MIN
4040064/E 08/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
相关型号:
TLC20A01E4871S
Array/Network Resistor, Bussed, Thin Film, 0.05W, 4870ohm, 100V, -25,25ppm/Cel, 3535,
VISHAY
TLC20A01E7681F
Array/Network Resistor, Bussed, Thin Film, 0.05W, 7680ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 3535,
VISHAY
TLC20A01H3400F
Array/Network Resistor, Bussed, Thin Film, 0.05W, 340ohm, 100V, 1% +/-Tol, -50,50ppm/Cel, 3535,
VISHAY
TLC20A01H3650F
Array/Network Resistor, Bussed, Thin Film, 0.05W, 365ohm, 100V, 1% +/-Tol, -50,50ppm/Cel, 3535,
VISHAY
TLC20A01H8660D
Array/Network Resistor, Bussed, Thin Film, 0.05W, 866ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 3535,
VISHAY
TLC20A01K2611B
Array/Network Resistor, Bussed, Thin Film, 0.05W, 2610ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 3535,
VISHAY
TLC20A01K5972S
Array/Network Resistor, Bussed, Thin Film, 0.05W, 59700ohm, 100V, -100,100ppm/Cel, 3535,
VISHAY
TLC20A01M1002F
Array/Network Resistor, Bussed, Thin Film, 0.05W, 10000ohm, 100V, 1% +/-Tol, -300,300ppm/Cel, 3535,
VISHAY
TLC20A01M1583S
Array/Network Resistor, Bussed, Thin Film, 0.05W, 158000ohm, 100V, -300,300ppm/Cel, 3535,
VISHAY
TLC20A01M9090D
Array/Network Resistor, Bussed, Thin Film, 0.05W, 909ohm, 100V, 0.5% +/-Tol, -300,300ppm/Cel, 3535,
VISHAY
TLC20A03E7150S
Array/Network Resistor, Isolated, Thin Film, 0.1W, 715ohm, 100V, -25,25ppm/Cel, 3535,
VISHAY
©2020 ICPDF网 联系我们和版权申明