TLC3574IN [TI]
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH; 5 V模拟3-5V数字14-12BIT 200 KSPS 4-8CHANNEL串行模拟数字转换器与型号: | TLC3574IN |
厂家: | TEXAS INSTRUMENTS |
描述: | 5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH |
文件: | 总49页 (文件大小:1484K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TLC3578, TLC2578
DW OR PW PACKAGE
(TOP VIEW)
D
14-Bit Resolution for TLC3574/78, 12-Bit for
TLC2574/2578
D
Maximum Throughput 200-KSPS
1
24
23
22
21
20
19
18
17
16
15
14
13
SCLK
FS
SDI
CSTART
D
Multiple Analog Inputs:
− 8 Single-Ended Channels for
TLC3578/2578
− 4 Single-Ended Channels for
TLC3574/2574
2
AV
DD
3
AGND
COMP
REFM
REFP
AGND
4
EOC/INT
SDO
DGND
5
6
D
D
D
Analog Input Range: 10 V
7
DV
DD
Pseudodifferential Analog Inputs
8
CS
A0
A1
A2
A3
AV
A7
A6
A5
A4
DD
9
SPI/DSP-Compatible Serial Interfaces With
SCLK up to 25-MHz
10
11
12
D
Built-In Conversion Clock and 8x FIFO
D
Single 5-V Analog Supply; 3-/5-V Digital
Supply
TLC3574, TLC2574
DW, N, OR PW PACKAGE
(TOP VIEW)
D
Low-Power
− 5.8 mA in Normal Operation
− 20 µA in Power Down
D
D
Programmable Autochannel Sweep and
Repeat
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
SCLK
FS
SDI
CSTART
AV
DD
AGND
COMP
REFM
REFP
AGND
Hardware-Controlled, Programmable
Sampling Period
EOC/INT
SDO
DGND
D
Hardware Default Configuration
D
INL: TLC3574/78: 1 LSB;
TLC2574/78: 0.5 LSB
DV
DD
CS
A0
A1
AV
A3
A2
DD
D
D
D
DNL: TLC3574/78: 0.5 LSB;
TLC2574/78: 0.5 LSB
SINAD: TLC3574/78: 79 dB;
TLC2574/78: 72 dB
THD: TLC3574/78: −82 dB;
TLC2574/78: −82 dB
description
The TLC3574, TLC3578, TLC2574, and TLC2578 are a family of high-performance, low-power, CMOS
analog-to-digital converters (ADC). TLC3574/78 is a 14-bit ADC; TLC2574/78 is a 12-bit ADC. All parts operate
from single 5-V analog power supply and 3-V to 5-V digital supply. The serial interface consists of four digital
input [chip select (CS), frame sync (FS), serial input-output clock (SCLK), serial data input (SDI)], and a 3-state
serial data output (SDO). CS (works as SS, slave select), SDI, SDO and SCLK form an SPI interface. FS, SDI,
SDO, and SCLK form DSP interface. The frame sync signal (FS) indicates the start of a serial data frame being
transferred. When multiple converters connect to one serial port of a DSP, CS works as the chip select to allow
the host DSP to access the individual converter. CS can be tied to ground if only one converter is used. FS must
be tied to DV
if it is not used (such as in an SPI interface). When SDI is tied to DV , the device is set in
DD
DD
hardware default mode after power on and no software configuration is required. In the simplest case, only three
wires (SDO, SCLK, and CS or FS) are needed to interface with the host.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢘ
ꢘ
ꢛ
ꢎ
ꢭ
ꢑ
ꢨ
ꢝ
ꢂ
ꢦ
ꢀ
ꢧ
ꢒ
ꢡ
ꢎ
ꢟ
ꢍ
ꢠ
ꢑ
ꢌ
ꢀ
ꢌ
ꢞ
ꢟ
ꢩ
ꢠ
ꢡ
ꢧ
ꢢ
ꢣ
ꢤ
ꢤ
ꢥ
ꢥ
ꢞ
ꢞ
ꢡ
ꢡ
ꢟ
ꢟ
ꢞ
ꢦ
ꢦ
ꢪ
ꢧ
ꢨ
ꢢ
ꢢ
ꢩ
ꢩ
ꢟ
ꢥ
ꢤ
ꢣ
ꢦ
ꢦ
ꢡ
ꢠ
ꢪ
ꢀꢩ
ꢨ
ꢫ
ꢦ
ꢬ
ꢞ
ꢧ
ꢤ
ꢦ
ꢥ
ꢞ
ꢥ
ꢡ
ꢢ
ꢟ
ꢨ
ꢭ
ꢤ
ꢟ
ꢥ
ꢥ
ꢩ
ꢦ
ꢮ
Copyright 2000 − 2003, Texas Instruments Incorporated
ꢢ
ꢡ
ꢧ
ꢥ
ꢡ
ꢢ
ꢣ
ꢥ
ꢡ
ꢦ
ꢪ
ꢞ
ꢠ
ꢞ
ꢧ
ꢩ
ꢢ
ꢥ
ꢯ
ꢥ
ꢩ
ꢢ
ꢡ
ꢠ
ꢰ
ꢤ
ꢒ
ꢟ
ꢣ
ꢩ
ꢦ
ꢥ
ꢤ
ꢟ
ꢭ
ꢤ
ꢢ
ꢭ
ꢱ
ꢤ
ꢥ ꢩ ꢦ ꢥꢞ ꢟꢳ ꢡꢠ ꢤ ꢬꢬ ꢪꢤ ꢢ ꢤ ꢣ ꢩ ꢥ ꢩ ꢢ ꢦ ꢮ
ꢢ
ꢢ
ꢤ
ꢟ
ꢥ
ꢲ
ꢮ
ꢘ
ꢢ
ꢡ
ꢭ
ꢨ
ꢧ
ꢥ
ꢞ
ꢡ
ꢟ
ꢪ
ꢢ
ꢡ
ꢧ
ꢩ
ꢦ
ꢦ
ꢞ
ꢟ
ꢳ
ꢭ
ꢡ
ꢩ
ꢦ
ꢟ
ꢡ
ꢥ
ꢟ
ꢩ
ꢧ
ꢩ
ꢦ
ꢦ
ꢤ
ꢢ
ꢞ
ꢬ
ꢲ
ꢞ
ꢟ
ꢧ
ꢬ
ꢨ
ꢭ
ꢩ
1
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
description (continued)
In addition to being a high-speed ADC with versatile control capability, these devices have an on-chip analog
multiplexer (MUX) that can select any analog input or one of three self-test voltages. The sample-and-hold
function is automatically started after the fourth SCLK (normal sampling) or can be controlled by a special pin,
CSTART, to extend the sampling period (extended sampling). The normal sampling period can also be
programmed as short sampling (12 SCLKs) or long sampling (44 SCLKs) to accommodate the faster SCLK
operation popular among high-performance signal processors. The TLC3574/78 and TLC2574/78 are
designed to operate with low-power consumption. The power saving feature is further enhanced with
autopower-down mode and programmable conversion speeds. The conversion clock (internal OSC) is built in.
The converter can also use an external SCLK as the conversion clock for maximum flexibility. The TLC3574/78
and TLC2574/78 are specified with bipolar input and a full scale range of 10 V.
AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
20-TSSOP
(PW)
20-SOIC
(DW)
20-PDIP
(N)
24-SOIC
(DW)
24-TSSOP
(PW)
TLC2574IPW
TLC3574IPW
TLC2574IDW
TLC3574IDW
TLC2574IN
TLC3574IN
TLC2578IDW
TLC3578IDW
TLC2578IPW
TLC3578IPW
−40°C to 85°C
functional block diagram
DV
AV
DD
DD
REFP
COMP
REFM
†
X8
‡
X4
A0 A0
A1 A1
A2 A2
A3 A3
FIFO
X8
SAR
ADC
Analog
MUX
Signal
Scaling
OSC
A4
A5
A6
A7
X
X
X
X
SDO
Conversion
Clock
Command
Decode
CFR
SDI
CMR (4 MSBs)
SCLK
CS
FS
Control
Logic
4-Bit
EOC/INT
Counter
CSTART
DGND AGND
†
‡
TLC3578, TLC2578
TLC3574, TLC2574
NOTE: 4-Bit counter counts the CLOCK, SCLK. The CLOCK is gated in by CS falling edge if CS initiates the conversion operation cycle, or gated
in by the rising edge of FS if FS initiates the operation cycle. SCLK is disabled for serial interface when CS is high.
2
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
equivalent input circuit
V
DD
REFP
Bipolar Signal Scaling
MUX
Digital Input
3.94 kΩ
6.6 kΩ
1.5 kΩ
9.9 kΩ
Ain
R
on
C
= 30 pF
(sample)
Equivalent Digital Input Circuit
REFM
Diode Turn on Voltage: 35 V
Equivalent Analog Input Circuit
Terminal Functions
TERMINAL
NO.
I/O
DESCRIPTION
NAME
TLC3574 TLC3578
TLC2574 TLC2578
A0
A0
A1
A2
A3
A4
A5
A6
A7
9
9
I
Analog signal inputs. Analog input signals applied to these terminals are internally multiplexed. The
driving source impedance should be less than or equal to 25 Ω for normal sampling. For larger
source impedance, use the external hardware conversion start signal CSTART (the low time of
CSTART controls the sampling period) or reduce the frequency of SCLK to increase the sampling
time.
A1
A2
A3
10
11
12
10
11
12
13
14
15
16
AGND
14, 18
18, 22
I
Analog ground return for the internal circuitry. Unless otherwise noted, all analog voltage
measurements are with respect to AGND.
AV
DD
13, 19
17
17, 23
21
I
I
I
Analog supply voltage
COMP
CS
Internal compensation pin. Install compensation capacitors 0.1 µF between this pin and AGND.
8
8
Chip select. When CS is high, SDO is in high-impedance state, SDI is ignored, and SCLK is
disabled to clock data, but works as conversion clock source if programmed. The falling edge of
CS input resets the internal 4-bit counter, enables SDI and SCLK, and removes SDO from
high-impedance state.
If FS is high at CS falling edge, CS falling edge initiates the operation cycle. CS works as slave
select (SS) to provide an SPI interface.
If FS is low at CS falling edge, FS rising edge initiates the operation cycle. CS can be used as chip
select to allow host to access the individual converter.
CSTART
20
24
I
External sampling trigger signal, which initiates the sampling from a selected analog input channel
when the device works in extended sampling mode (asynchronous sampling). A high-to-low
transition starts the sampling of the analog input signal. A low-to-high transition puts the S/H in hold
mode and starts the conversion. The low time of the CSTART signal controls the sampling period.
CSTART signal must stay low long enough for proper sampling. CSTART must stay high long
enough after the low-to-high transition for the conversion to finish maturely. The activation of
CSTART is independent of SCLK and the level of CS and FS. However, the first CSTART cannot
be issued before the rising edge of the eleventh SCLK. Tie this pin to DV
Digital ground return for the internal circuitry
Digital supply voltage
if not used.
DD
DGND
DV
6
7
6
7
I
I
DD
3
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
Terminal Functions (Continued)
TERMINAL
NO.
I/O
TLC3574 TLC3578
TLC2574 TLC2578
DESCRIPTION
NAME
EOC(INT)
4
4
O
End of conversion (EOC) or interrupt to host processor (INT)
EOC: used in conversion mode 00 only. EOC goes from high to low at the end of the sampling and
remains low until the conversion is complete and data is ready.
INT: Interrupt to the host processor. The falling edge of INT indicates data is ready for output. INT
is cleared by the following CS↓, FS↑, or CSTART↓.
FS
2
2
I
Frame sync input from DSP. The rising edge of FS indicates the start of a serial data frame being
transferred (coming into or being sent out of the device). If FS is low at the falling edge of CS, the
rising edge of FS initiates the operation cycle, resets the internal 4-bit counter, and enables SDI,
SDO, and SCLK. Tie this pin to DV
DD
if FS is not used to initiate the operation cycle.
REFM
REFP
16
15
20
19
I
I
External low reference input. Connect REFM to AGND.
External positive reference input. The range of maximum input voltage is determined by the
difference between the voltage applied to this terminal and to the REFM terminal. Always install
decoupling capacitors (10 µF in parallel with 0.1 µF) between REFP and REFM.
SCLK
SDI
1
3
1
3
I
I
Serial clock input from the host processor to clock in the input from SDI and clock out the output
via SDO. It can also be used as the conversion clock source when the external conversion clock
is selected (see Table 2). When CS is low, SCLK is enabled. When CS is high, SCLK is disabled
for the data transfer, but can still work as the conversion clock source.
Serial data input. The first 4 MSBs, ID[15:12], are decoded as one 4-bit command. All trailing bits,
except for the WRITE CFR command, are filled with zeros. The WRITE CFR command requires
additional 12-bit data. The MSB of input data, ID(15), is latched at the first falling edge of SCLK
following FS falling edge if FS starts the operation, or latched at the falling edge of first SCLK
following CS falling edge when CS initiates the operation.
The remaining input data (if any) is shifted in on the rising edge of SCLK and latched on the falling
edge of SCLK. The input via SDI is ignored after the 4-bit counter counts to 16 (clock edges) or a
low-to-high transition of CS, whichever happens first. Refer to the timing specification for the timing
requirements. Tie SDI to DV
DD
if using hardware default mode (refer to Device Initialization).
SDO
5
5
O
The 3-state serial output for the A/D conversion result. All data bits are shifted out through SDO.
SDO is in the high-impedance state when CS is high. SDO is released after a CS falling edge. The
output format is MSB (OD15) first.
When FS initiates the operation, the MSB of output via SDO, OD(15), is valid before the first falling
edge of SCLK following the falling edge of FS.
When CS initiates the operation, the MSB, OD(15), is valid before the first falling edge of SCLK
following the CS falling edge.
The remaining data bits (if any) are shifted out on the rising edge of SCLK and are valid before the
falling edge of SCLK. Refer to the timing specification for the details.
In select/conversion operation, the first 14 bits (for TLC3574/78) or the first 12 bits (for TLC2574/78)
are the results from the previous conversion (data). In a READ FIFO operation, this data is from
FIFO. In both cases, the last two bits (for TLC3574/78) or the last four bits (for TLC2574/78) are
don’t care.
In a WRITE operation, the output from SDO must be ignored.
SDO goes into high-impedance state at the 16th falling edge of SCLK after the operation cycle is
initiated. SDO is in high-impedance state during conversions in modes 01, 10, and 11.
4
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
†
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
Supply voltage, GND to AV
and DV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6.5 V
DD
DD
Analog input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −17 V to 17 V
Analog input current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA MAX
Reference input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AV
Digital input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to DV
+ 0.3 V
+ 0.3 V
DD
DD
Operating virtual junction temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 150°C
J
Operating free-air temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
A
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
stg
Lead temperature 1,6 mm (1.16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under electrical characteristics and timing
characteristics is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
general electrical characteristics over recommended operating free-air temperature range,
single-ended input, normal long sampling, 200 KSPS, AV
= 5 V, V
= 4 V, V
= 0 V,
DD
REFP
REFM
SCLK frequency = 25 MHz, fixed channel at CONV mode 00, analog input signal source resistance
= 25 Ω (unless otherwise noted)
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX UNIT
Digital Input
DV
DV
DV
DV
= 5 V
= 3 V
= 5 V
= 3 V
3.8
2.1
DD
DD
DD
DD
V
High-level digital input voltage
Low-level digital input voltage
V
IH
IL
0.8
V
V
0.6
I
I
High-level digital input current
Low-level digital input current
Input capacitance
V = DV
0.005
2.5
µA
µA
pF
IH
I
DD
V = DGND
I
−2.5 −0.005
20
IL
25
Digital Output
DV
DV
= 5 V
= 3 V
4.2
2.4
DD
DD
V
V
I
High-level digital output at 30 pF load
Low-level digital output at 30 pF load
I
= −0.2 mA
V
V
OH
o
I
o
I
o
I
o
I
o
= 0.8 mA
= 50 µA
= 0.8 mA
= 50 µA
0.4
0.1
0.4
0.1
1
DV
DV
= 5 V
= 3 V
DD
OL
DD
V
= DV
DD
0.02
Off-state output current
(high-impedance state)
O
µA
CS = DV
DD
OZ
V
= DGND
−1
0.02
O
Power Supply
AV
DD
4.75
2.7
5
5
5.5
5.5
V
V
Supply voltage
DV
DD
AV
Al
current
current
DD
CC
4.2
1.6
5
Conversion clock is internal OSC,
AV = 5.5 V − 4.5 V, CS = DGND,
Power supply cur-
rent
I
mA
CC
DD
Excluding bipolar input biasing current
DV
Dl
CC
DD
2.0
I
For all digital inputs = DV
or DGND,
= 5.5 V, Excluding bipolar input
SCLK OFF
SCLK ON
20
CC
DD
AV
DD
µA
°C
(autopwrdn):
Autopower-down power supply
current
175
230
85
biasing current, external reference
Operating temperature
−40
†
All typical values are at T = 25°C.
A
5
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
general electrical characteristics over recommended operating free-air temperature range, single-
ended input, normal long sampling, 200 KSPS, AV
= 5 V, V
= 4 V, V
= 0 V,
DD
REFP
REFM
SCLK frequency = 25 MHz, fixed channel at CONV mode 00, analog input signal source
resistance = 25 Ω (unless otherwise noted)
TLC3574/78 and TLC2574/78
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
Resolution
14
bits
Analog Input
Voltage range
−10
10
V
Selected channel at 10 V
Selected channel at –10 V
0.8
−1.2
10
1.6
Selected analog input channel bias current
mA
−1.6
Impedance
Capacitance
Reference
kΩ
30
pF
V
Positive reference voltage
Negative reference voltage
3.96
0
4
4.04
V
V
REFP
REFM
V
AGND
No conversion (AV
SCLK=DGND)
= 5V, CS= DV ,
DD
DD
100
8.3
MΩ
kΩ
µA
Input impedance
Normal long sampling (AV
DD
SCLK = 25 MHz, External conversion clock)
= 5V, CS=DGND,
12.5
0.4
No conversion (AV = 5 V,
DD
SCLK = DGND, CS = DV
1.5
0.6
)
DD
Reference current
Normal long sampling (AV
External conversion clock, SCLK = 25 MHz,
= 5 V, CS = DGND,
DD
mA
V
= 5 V)
REF
DV
Internal oscillation frequency
Conversion time
= 2.7 V – 5.5 V
6.5
MHz
DD
TLC3574/78
TLC2574/78
TLC3574/78
TLC2574/78
2.785
2.015
Internal OSC, 6.5 MHz minimum
t
µS
(conv)
2.895
2.095
1.2
Conversion clock is external source,
SCLK = 25 MHz (see Note 1)
Acquisition time
Normal short sampling
µS
Normal long sampling, fixed channel
in mode 00 or 01
Throughput rate (see Note 2)
200
KSPS
†
All typical values are at T = 25°C.
A
NOTES: 1. Conversion time t
is (18 × 4 × SCLK) + 15 ns for TLC3574/78. Conversion time is (13 × 4 × SCLK) + 15 ns for TLC2574/78.
(conv)
2. This is for a fixed channel in conversion mode 00 or 01. When switching the channels, additional multiplexer setting time is required
to overcome the memory effect of the charge redistribution DAC.
6
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
AC/DC performance over recommended operating free-air temperature range, single-ended input,
normal long sampling, 200 KSPS, AV
= 5 V, V
= 4 V, V
= 0 V, SCLK frequency = 25 MHz,
DD
REFP
REFM
fixed channel at CONV mode 00, analog input signal source resistance = 25 Ω (unless otherwise
noted)
TLC3574/78 DW and PW package device AC/DC performance
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
DC Accuracy—Normal Long Sampling
E
E
E
E
E
Integral linearity error
Differential linearity error
Bipolar zero error
See Note 3
−1.5
−1
1
1.5
1
LSB
LSB
L
0.5
0.08
0.04
0.13
D
See Note 4
See Note 4
See Note 4
−0.30
−0.55
−0.30
0.36
0.61
0.79
%FS
%FS
%FS
O
Positive full scale error
Negative full scale error
FS(+)
FS(−)
DC Accuracy—Normal Short Sampling
E
E
E
E
E
Integral linearity error
Differential linearity error
Bipolar zero error
See Note 3
1
0.5
LSB
LSB
L
D
See Note 4
See Note 4
See Note 4
0.08
0.04
0.13
%FS
%FS
%FS
O
Positive full scale error
Negative full scale error
FS(+)
FS(−)
AC Accuracy (see Note 3)—Normal Long Sampling
f = 20 kHz
76
79
75
i
SINAD
THD
Signal-to-noise ratio + distortion
Total harmonic distortion
Signal-to-noise ratio
dB
dB
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
−82
−78
80
−77
78
12.3
78
SNR
dB
78
12.8
12.2
84
ENOB
SFDR
Effective number of bits
Bits
Spurious free dynamic range
Channel-to-channel isolation
dB
dB
f = 100 kHz
i
79
Fixed channel in conversion mode 00, f = 35 kHz,
i
See Notes 2 and 5
81
Full power bandwidth, −3 dB
Full power bandwidth, −1 dB
1
MHz
kHz
Analog input bandwidth
700
†
All typical values are at T = 25°C.
A
NOTES: 2. This is for a fixed channel in conversion mode 00 or 01. When switching the channels, additional multiplexer setting time is required
to overcome the memory effect of the charge redistribution DAC.
3. Linear error is the maximum deviation from the best fit straight line through the A/D transfer characteristics.
4. Bipolar zero error is the difference between 10000000000000 and the converted output for zero input voltage; positive full-scale error
is the difference between 11111111111111 and the converted output for positive full-scale input voltage (10 V); negative full-scale
error is the difference between 00000000000000 and the converted output for negative full-scale input voltage (−10 V).
5. It is measured by applying a full-scale of 35 kHz signal to other channels and determining how much the signal is attenuated in the
channel of interest. The converter samples this examined channel continuously. The channel-to-channel isolation is degraded if the
converter samples different channels alternately.
7
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TLC3574/78 DW and PW package device AC/DC performance (continued)
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
AC Accuracy—Normal Short Sampling
f = 20 kHz
79
75
i
SINAD
THD
Signal-to-noise ratio + distortion
Total harmonic distortion
Signal-to-noise ratio
dB
dB
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
−82
−78
80
SNR
dB
f = 100 kHz
i
78
f = 20 kHz
12.8
12.2
84
i
ENOB
SFDR
Effective number of bits
Bits
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
Spurious free dynamic range
Channel-to-channel isolation
dB
dB
79
Fixed channel in conversion mode 00, f = 35 kHz,
i
See Notes 2 and 5
81
Full power bandwidth, −3 dB
Full power bandwidth, −1 dB
1
MHz
kHz
Analog input bandwidth
700
†
All typical values are at T = 25°C.
A
NOTES: 2. This is for a fixed channel in conversion mode 00 or 01. When switching the channels, additional multiplexer setting time is required
to overcome the memory effect of the charge redistribution DAC.
5. It is measured by applying a full-scale of 35 kHz signal to other channels and determining how much the signal is attenuated in the
channel of interest. The converter samples this examined channel continuously. The channel-to-channel isolation is degraded if the
converter samples different channels alternately.
8
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TLC3574I N package device AC/DC performance
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
DC Accuracy—Normal Long Sampling
E
E
E
E
E
Integral linearity error
Differential linearity error
Bipolar zero error
See Note 3
−1.5
−1
1
1.5
1.5
LSB
LSB
L
0.8
0.08
0.04
0.13
D
See Note 4
See Note 4
See Note 4
−0.30
−0.55
−0.30
0.36
0.61
0.79
%FS
%FS
%FS
O
Positive full scale error
Negative full scale error
FS(+)
FS(−)
DC Accuracy—Normal Short Sampling
E
E
E
E
E
Integral linearity error
Differential linearity error
Bipolar zero error
See Note 3
1.8
0.8
LSB
LSB
L
D
See Note 4
See Note 4
See Note 4
0.08
0.04
0.13
%FS
%FS
%FS
O
Positive full-scale error
Negative full-scale error
FS(+)
FS(−)
AC Accuracy (see Note 3)—Normal Long Sampling
f = 20 kHz
75
78
75
i
SINAD
THD
Signal-to-noise ratio + distortion
Total harmonic distortion
Signal-to-noise ratio
dB
dB
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
−82
−75
80
−77
78
12.2
78
SNR
dB
76
12.7
12.2
83
ENOB
SFDR
Effective number of bits
Bits
Spurious free dynamic range
Channel-to-channel isolation
dB
dB
f = 100 kHz
i
75
Fixed channel in conversion mode 00, f = 35 kHz,
i
See Notes 2 and 5
81
Full power bandwidth, −3 dB
Full power bandwidth, −1 dB
1
MHz
kHz
Analog input bandwidth
700
†
All typical values are at T = 25°C.
A
NOTES: 2. This is for a fixed channel in conversion mode 00 or 01. When switching the channels, additional multiplexer setting time is required
to overcome the memory effect of the charge redistribution DAC.
3. Linear error is the maximum deviation from the best fit straight line through the A/D transfer characteristics.
4. Bipolar zero error is the difference between 10000000000000 and the converted output for zero input voltage; positive full-scale error
is the difference between 11111111111111 and the converted output for positive full-scale input voltage (10 V); negative full-scale
error is the difference between 00000000000000 and the converted output for negative full-scale input voltage (−10 V).
5. It is measured by applying a full-scale of 35 kHz signal to other channels and determining how much the signal is attenuated in the
channel of interest. The converter samples this examined channel continuously. The channel-to-channel isolation is degraded if the
converter samples different channels alternately.
9
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TLC3574I N package device AC/DC performance (continued)
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
AC Accuracy—Normal Short Sampling
f = 20 kHz
76
70
i
SINAD
THD
Signal-to-noise ratio + distortion
Total harmonic distortion
Signal-to-noise ratio
dB
dB
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
f = 20 kHz
i
−81
−74
78
SNR
dB
f = 100 kHz
i
75
f = 20 kHz
12.3
11.3
83
i
ENOB
SFDR
Effective number of bits
Bits
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
Spurious free dynamic range
Channel-to-channel isolation
dB
dB
75
Fixed channel in conversion mode 00, f = 35 kHz,
i
See Notes 2 and 5
81
Full power bandwidth, −3 dB
Full power bandwidth, −1 dB
1
MHz
kHz
Analog input bandwidth
700
†
All typical values are at T = 25°C.
A
NOTES: 2. This is for a fixed channel in conversion mode 00 or 01. When switching the channels, additional multiplexer setting time is required
to overcome the memory effect of the charge redistribution DAC.
5. It is measured by applying a full-scale of 35 kHz signal to other channels and determining how much the signal is attenuated in the
channel of interest. The converter samples this examined channel continuously. The channel-to-channel isolation is degraded if the
converter samples different channels alternately.
10
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TLC2574/78 DW and PW package devices AC/DC performance
†
TYP
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
DC Accuracy
E
E
E
E
E
Integral linearity error
Differential linearity error
Bipolar zero error
See Note 6
−1
−1
0.5
0.5
1
1
LSB
LSB
L
D
See Note 7
See Note 7
See Note 7
−0.30
−0.55
−0.30
0.08
0.04
0.13
0.36
0.61
0.79
%FS
%FS
%FS
O
Positive full scale error
Negative full scale error
FS(+)
FS(−)
AC Accuracy
f = 20 kHz
70
72
70
i
SINAD
THD
Signal-to-noise ratio + distortion
dB
dB
f = 100 kHz
i
f = 20 kHz
i
−82
−80
72
−76
Total harmonic distortion
Signal-to-noise ratio
f = 100 kHz
i
f = 20 kHz
i
71
11.3
78
SNR
dB
f = 100 kHz
i
71
f = 20 kHz
i
11.7
11.3
83
ENOB
SFDR
Effective number of bits
Spurious free dynamic range
Bits
dB
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
80
Full power bandwidth, −3 dB
Full power bandwidth, −1 dB
1
MHz
kHz
Analog input bandwidth
700
Fixed channel in conversion mode 00, f = 35 kHz,
i
See Note 8
Channel-to-channel Isolation
81
dB
†
All typical values are at T = 25°C.
A
NOTES: 6. Linear error is the maximum deviation from the best fit straight line through the A/D transfer characteristics.
7. Bipolar zero error is the difference between 100000000000 and the converted output for zero input voltage; positive full-scale error
is the difference between 111111111111 and the converted output for positive full-scale input voltage (10 V); negative full-scale error
is the difference between 000000000000 and the converted output for negative full-scale input voltage (−10 V).
8. It is measured by applying a full-scale of 35 kHz signal to other channels and determining how much the signal is attenuated in the
channel of interest. The converter samples this examined channel continuously. The channel-to-channel isolation is degraded if the
converter samples different channels alternately.
11
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TLC2574I N package device AC/DC performance
†
PARAMETER
TEST CONDITIONS
MIN TYP
MAX
UNIT
DC Accuracy
E
E
E
E
E
Integral linearity error
Differential linearity error
Bipolar zero error
see Note 6
−1
−1
0.7
0.7
1
1
LSB
LSB
L
D
see Note 7
see Note 7
see Note 7
−0.30
−0.55
−0.30
0.08
0.04
0.13
0.36
0.61
0.79
%FS
%FS
%FS
O
Positive full-scale error
Negative full-scale error
FS(+)
FS(−)
AC Accuracy
f = 20 kHz
70
72
70
i
SINAD
THD
Signal-to-noise + distortion
dB
dB
f = 100 kHz
i
f = 20 kHz
i
−82
−75
72
−76
Total harmonic distortion
Signal-to-noise ratio
f = 100 kHz
i
f = 20 kHz
i
70
11.3
77
SNR
dB
f = 100 kHz
i
71
f = 20 kHz
i
11.7
11.3
83
ENOB
SFDR
Effective number of bits
Spurious free dynamic range
Bits
dB
f = 100 kHz
i
f = 20 kHz
i
f = 100 kHz
i
75
Full power bandwidth, −3 dB
Full power bandwidth, −1 dB
1
MHz
kHz
Analog input bandwidth
700
Fixed channel in conversion mode 00, f = 35 kHz,
i
See Note 8
Channel-to-channel Isolation
81
dB
†
All typical values are at T = 25°C.
A
NOTES: 6. Linear error is the maximum deviation from the best fit straight line through the A/D transfer characteristics.
7. Bipolar zero error is the difference between 100000000000 and the converted output for zero input voltage; positive full-scale error
is the difference between 111111111111 and the converted output for positive full-scale input voltage (10 V); negative full-scale error
is the difference between 000000000000 and the converted output for negative full-scale input voltage (−10 V).
8. It is measured by applying a full-scale of 35 kHz signal to other channels and determining how much the signal is attenuated in the
channel of interest. The converter samples this examined channel continuously. The channel-to-channel isolation is degraded if the
converter samples different channels alternately.
12
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
timing requirements over recommended operating free-air temperature range, AV
= 5 V,
DD
DV
= 5 V, V
= 4 V, V
= 0 V, SCLK frequency = 25 MHz (unless otherwise noted)
DD
REFP
REFM
SCLK, SDI, SDO, EOC and INT
PARAMETERS
Cycle time of SCLK, 25 pF load (see Note 10)
MIN
100
40
TYP
MAX
UNIT
DV
DV
= 2.7 V
= 5 V
DD
t
t
ns
c(1)
DD
Pulse width of SCLK High, at 25-pF load
Rise time for INT and EOC, at 10-pF load
40%
60%
6
t
w(1)
c(1)
DV
DV
DV
DV
= 5 V
DD
DD
DD
DD
t
ns
r(1)
f(1)
= 2.7 V
= 5 V
10
6
t
Fall time for INT and EOC, at 10-pF load
ns
= 2.7 V
10
−
t
t
Setup time, new SDI valid (reaches 90% final level) before the falling edge of SCLK, at 25-pF load
Hold time, old SDI hold (reaches 10% of old data level) after falling edge of SCLK, at 25-pF load
6
0
0
0
0
0
ns
ns
su(1)
−
h(1)
DV
DV
= 5 V
10
23
−
Delay time, new SDO valid (reaches 90% of final level) after SCLK rising edge, at 10-pF
load (see Note 11)
DD
t
t
ns
d(1)
= 2.7 V
DD
Hold time, old SDO hold (reaches 10% of old data level) after SCLK rising edge, at 10-pF load
ns
ns
ns
h(2)
td(2)
Delay time, delay from the falling edge of 16th SCLK to EOC falling edge, normal sampling, at 10-pF load
Delay time, delay from the falling edge of 16th SCLK to INT falling edge, at 10-pF load (see Notes 11 and 12)
6
t
t
t
+6
d(3)
(conv)
(conv)
NOTES: 9. The minimum pulse width of SCLK high and low is 12.5 ns.
10. Specified by design
11. For normal short sampling, t
is the delay from the falling edge of 16th SCLK to the falling edge of INT.
is the delay from the falling edge of 48th SCLK to the falling edge of INT. Conversion time, t
d(3)
For normal long sampling, t
d(3)
,
(conv)
is equal to 18 × OSC +15 ns (for TLC3574 and TLC3578) or 13 × OSC + 15 ns (for TLC2574 and TLC2578) when using internal
OSC as conversion clock, or 72 × t
external SCLK is conversion clock source.
+ 15 ns (for TLC3574 and TLC3578) or 52 × t
+ 15 ns (for TLC2574 and TLC2578) when
c(1)
c(1)
V
90%
50%
IH
CS
10%
V
IL
t
c(1)
16
t
w(1)
1
SCLK
SDI
t
h(1)
ID0
t
su(1)
Don’t Care
ID15 ID1
Don’t Care
t
d(1)
t
h(2)
Hi-Z
Hi-Z
OD15 OD1
OD0
SDO
EOC
†
t
t
d(2)
r(1)
t
OR
f(1)
‡
t
d(3)
INT
t
f(1)
t
r(1)
†
‡
For normal long sampling, t
For normal long sampling, t
is the delay time of EOC low after the falling edge of 48th SCLK.
is the delay time of INT low after the falling edge of 48th SCLK.
d(2)
d(3)
− − − − The dotted line means signal may or may not exist, depending on application. It must be ignored.
Normal sampling mode, CS initiatesthe conversion, FS must be tied to high. When CS is high, SDO is in Hi-Z, all inputs (FS, SCLK,
SDI) are inactive and are ignored.
Figure 1. Critical Timing for SCLK, SDI, SDO, EOC and INT
13
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
timing requirements over recommended operating free-air temperature range, AV
= 5 V,
DD
DV
= 5 V, V
= 4 V, V
=0V, SCLK frequency = 25 MHz (unless otherwise noted) (continued)
DD
REFP
REFM
CS trigger
PARAMETERS
MIN
TYP
MAX
UNIT
t
t
t
(2) Setup time, CS falling edge before SCLK rising edge, at 25-pF load
12
ns
su
Delay time, delay time from the falling edge of 16th SCLK to CS rising edge, at 25 pF load
(see Note 12)
5
ns
d(4)
w(2)
Pulse width of CS high, at 25-pF load
1
0
0
0
0
0
t
c(1)
DV
DV
= 5 V
12
DD
DD
Delay time, delay from CS falling edge to MSB of SDO valid (reaches 90%
final level), at 10 pF load
t
ns
d(5)
d(6)
†
30
= 2.7 V
t
Delay time, delay from CS rising edge to SDO 3-state, at 10-pF load
6
6
ns
DV
DV
= 5 V
DD
DD
t
Delay time, delay from CS falling edge to INT rising edge, at 10-pF load
ns
d(7)
†
16
= 2.7 V
†
Specified by design
NOTE 12: For normal short sampling, t
is the delay time from the falling edge of 16th SCLK to CS rising edge.
d(4)
is the delay time from the falling edge of 48th SCLK to CS rising edge.
d(4)
For normal long sampling, t
V
V
IH
CS
IL
t
su(2)
t
t
w(2)
d(4)
1
16
SCLK
SDI
Don’t Care
ID15 ID1
ID0
Don’t Care
Hi-Z
Don’t Care
t
d(6)
t
d(5)
Hi-Z
Hi-Z
OD15 OD1
OD0
OD15
OD7
SDO
EOC
OR
t
d(7)
INT
− − − − The dotted line means signal may or may not exist, depending on application. It must be ignored.
Normal sampling mode, CS initiates the conversion, FS must be tied to high. When CS is high, SDO is in Hi-Z, all inputs (FS, SCLK,
SDI) are inactive and are ignored.
Figure 2. Critical Timing for CS Trigger
14
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
timing requirements over recommended operating free-air temperature range, AV
= 5 V,
DD
DV
= 5 V, V
= 4 V, V
=0V, SCLK frequency = 25 MHz (unless otherwise noted) (continued)
DD
REFP
REFM
FS trigger
PARAMETERS
MIN
TYP
MAX
UNIT
t
t
t
Delay time, delay from CS falling edge to FS rising edge at 25-pF load
Setup time, FS rising edge before SCLK falling edge at 25-pF load
Pulse width of FS high, at 25-pF load
0.5
t
d(8)
c(1)
ns
0.25×t
0.75×t
0.5×t
+ 5
su(3)
w(3)
c(1)
c(1)
t
1.25×t
ns
c(1)
c(1)
c(1)
26
DV
= 5 V
DD
DD
Delay time, delay from FS rising edge to MSB of SDO valid
(reaches 90% final level), at 10-pF load
t
ns
d(9)
DV
= 2.7 V
30†
Required
t
Delay time, delay from FS rising edge to next FS rising edge, at 25-pF load
sampling time +
conversion time
ns
ns
d(10)
DV
DV
= 5 V
0
0
6
DD
DD
Delay time, delay from FS rising edge to INT rising edge, at
10-pF load
t
d(11)
= 2.7 V
16†
†
Specified by design
V
IH
t
d(10)
CS
FS
V
IL
t
t
w(3)
d(8)
t
su(3)
16
1
SCLK
SDI
Don’t Care
ID15 ID1
OD1
ID0
Don’t Care
ID15
Don’t Care
Don’t Care
t
d(9)
Hi-Z
Hi-Z
OD15
OD0
OD15
SDO
V
OH
EOC
OR
t
V
OH
d(11)
INT
− − − − The dotted line means signal may or may not exist, depending on application. It must be ignored.
Normal sampling mode, FS initiates the conversion, CS can be tied to low. When CS is high, SDO is in Hi-Z, all inputs (FS, SCLK,
SDI) are inactive and are ignored.
Figure 3. Critical Timing for FS Trigger
15
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
timing requirements over recommended operating free-air temperature range, AV
= 5 V,
DD
DV
= 5 V, V
= 4 V, V
=0V, SCLK frequency = 25 MHz (unless otherwise noted) (continued)
DD
REFP
REFM
CSTART trigger
PARAMETERS
MIN
TYP
MAX
UNIT
ns
Delay time, delay from CSTART rising edge to EOC falling edge, at 10-pF
load
t
t
t
0
15
21
d(12)
t
+0.4
µs
Pulse width of CSTART low, at 25-pF load (see Note 13)
w(4)
(sample_reg)
Delay time, delay from CSTART rising edge to CSTART falling edge, at 25-pF
load (see Note 13 and 14)
t
+15
ns
ns
ns
d(13)
(conv)
Delay time, delay from CSTART rising edge to INT falling edge, at 10-pF
load (see Note 13 and 14)
t
t
+15
t
+21
6
d(14)
d(15)
(conv)
(conv)
Delay time, delay from CSTART falling edge to INT rising edge, at 10-pF
load
t
0
NOTES: 13. The pulse width of the CSTART must be not less than the required sampling time.
The delay from CSTART rising edge to following CSTART falling edge must be not less than the required conversion time.
The delay from CSTART rising edge to the INT falling edge is equal to the conversion time.
14. The maximum rate of SCLK is 25 MHz for normal long sampling and 10 MHz for normal short sampling.
t
t
d(13)
w(4)
CSTART
EOC
t
(conv)
t
d(12)
t
d(15)
OR
t
d(14)
INT
Figure 4. Critical Timing for Extended Sampling (CSTART Trigger)
16
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
circuit description
converter
The converters include a successive-approximation ADC utilizing a charge redistribution DAC. Figure 5 shows
a simplified block diagram of the ADC. The sampling capacitor acquires the signal on Ain during the sampling
period. When the conversion process starts, the control logic directs the charge redistribution DAC to add and
subtract fixed amounts of charge from the sampling capacitor to bring the comparator into a balanced condition.
When balanced, the conversion is complete and the ADC output code is generated.
Charge
Redistribution
DAC
_
Ain
Control
Logic
ADC Code
C
(sample)
+
REFM
Figure 5. Simplified Block Diagram of the Successive-Approximation System
analog input range and internal test voltages
TLC3578 and TLC2578 have 8 analog inputs (TLC3574 and TLC2574 have 4) and three test voltages. The
inputs are selected by the analog multiplexer according to the command entered (see Table 1). The input
multiplexer is a break-before-make type to reduce input-to-input noise injection resulting from channel
switching.
All converters are specified for bipolar input range of 10 V. The input signal is scaled to 0–4 V at the SAR ADC
input via the bipolar scaling circuit (see the functional block diagram and the equivalent analog input circuit):
–10 V to 0 V, 10 V to 4 V, and 0 V to 2 V.
analog input mode
Two input signal modes can be selected: single-ended input and pseudodifferential input.
Charge
Redistribution
DAC
S1
_
Ain(+)
Ain(−)
Control
Logic
ADC Code
+
REFM
When sampling, S1 is closed and S2 connects to Ain(−).
During conversion, S1 is open and S2 connects to REFM.
Figure 6. Simplified Pseudodifferential Input Circuit
Pseudodifferential input refers to the negative input, Ain(−). Its voltage is limited in magnitude to 1 V. The input
frequency limit of Ain(−) is the same as the positive input Ain(+). This mode is normally used for ground noise
rejection or dc offset.
17
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
analog input mode (continued)
When pseudodifferential mode is selected, only two analog input channel pairs are available for the TLC3574
and TLC2574 and four channel pairs for the TLC3578 and TLC2578, because half the inputs are used as the
negative input.
Single Ended
Pseudodifferential
†
X8
‡
X4
†
X8
‡
X4
A0 A0
A1 A1
A2 A2
A3 A3
A0(+) Pair A
A1(−)
A2(+) Pair B
A3(−)
A4(+) Pair C
A5(−)
A6(+) Pair D
A7(−)
A0(+) Pair A
A1(−)
A2(+) Pair B
A3(−)
SAR
ADC
SAR
ADC
Analog
MUX
Analog
MUX
A4
A5
A6
A7
X
X
X
X
†
‡
TLC3578 and TLC2578
TLC3574 and TLC2574
Figure 7. Pin Assignment of Single-Ended Input vs Pseudodifferential Input
reference voltage
The external reference is applied to the reference-input pins (REFP and REFM). REFM should connect to
analog ground. REFP is 4 V. Install decoupling capacitors (10 µF in parallel with 0.1 µF) between REFP and
REFM, and compensation capacitors (0.1 µF) between COMP and AGND.
ideal conversion characteristics
Bipolar Analog Input Voltage
−9.99756 V
1LSB = 1.22 mV
9.99756 V
VBZS = 0.0 V
−0.61 mV 0.61 mV
−9.99878 V
−9.99939 V
VFS+ = 10 V
VFS− = −10 V
2s Complement
BTC
Binary
BOB
01111111111111
01111111111110
01111111111101
11111111111111
11111111111110
11111111111101
16383
16382
16381
8193
8192
8191
00000000000001
00000000000000
11111111111111
10000000000001
10000000000000
01111111111111
2
1
0
10000000000010
10000000000001
10000000000000
00000000000010
00000000000001
00000000000000
18
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
circuit description (continued)
data format
INPUT DATA FORMAT (BINARY)
MSB
LSB
ID[15:12]
ID[11:0]
Command
Configuration data field or filled with zeros
OUTPUT DATA FORMAT (READ CONVERSION/FIFO)
TLC3574 and TLC3578 TLC2574 and TLC2578
MSB
LSB
MSB
LSB
OD[15:2]
OD[1:0]
OD[15:4]
OD[3:0]
Conversion result
Don’t Care
Conversion result
Don’t Care
14-BIT (TLC3574/78)
Bipolar Input, Offset Binary: (BOB)
12-BIT (TLC2574/78)
Bipolar Offset Binary Output: (BOB)
Negative full scale code = VFS− = 0000h, Vcode = −10 V
Midscale code = VBZS = 2000h, Vcode = 0 V
Negative full scale code = 000h, Vcode = −10 V
Midscale code = 800h, Vcode = 0 V
Positive full scale code = VFS+ = 3FFFh, Vcode = 10 V − 1 LSB
Bipolar Input, Binary 2s Complement: (BTC)
Positive full scale code = FFFh, Vcode = 10 V − 1 LSB
Bipolar Input, Binary 2s Complement: (BTC)
Negative full scale code = 800 h, Vcode = −10 V
Midscale code = 000h, Vcode = 0 V
Negative full scale code = VFS− = 2000 h, Vcode = −10 V
Midscale code = VBZS = 0000h, Vcode = 0 V
Positive full scale code = VFS+ = 1FFFh, Vocde = 10 V − 1 LSB
Positive full scale code = 7FFh, Vocde = 10 V − 1 LSB
operation description
The converter samples the selected analog input signal, then converts the sample into digital output according
to the selected output format. The converter has four digital input pins (SDI, SCLK, CS, and FS) and one digital
output pin (SDO) to communicate with the host device. SDI is a serial data input pin, SDO is a serial data output
pin, and SCLK is a serial clock from host device. This clock is used to clock the serial data transfer. It can also
be used as conversion clock source (see Table 2). CS and FS are used to start the operation. The converter
has a CSTART pin for external hardware sampling and conversion trigger, and INT/EOC for interrupt purpose.
device initialization
After power on, the status of EOC/INT is initially high, and the input data register is set to all zeros. The device
must be initialized before starting conversion. The initialization procedure depends on the working mode. The
first conversion result must be ignored after power on.
Hardware Default Mode: Nonprogrammed mode, default. After power on, two consecutive active cycles
initiated by CS or FS put the device into hardware default mode if SDI is tied to DV . Each of these cycles must
DD
last 16 SCLK at least. These cycles initialize the converter and load CFR register with 800h (bipolar offset binary
output code, normal long sampling, internal OSC, single-ended input, one-shot conversion mode, and EOC/INT
pin as INT). No additional software configuration is required.
Software Programmed Mode: Programmed. If the converter needs to be configured, The host must write
A000H into converters first after power on, then performs the WRITE CFR operation to configure the device.
start of operation cycle
Each operation consists of several actions that the converter takes according to the command from the host.
The operation cycle includes three periods: command period, sampling period, and conversion period. In the
command period, the device decodes the command from host. In the sampling period, the device samples the
selected analog signal according to the command. In the conversion period, the sample of the analog signal
is converted to digital format. The operation cycle starts from the command period, which is followed by one
or several sampling and conversion periods (depending on the setting), and finishes at the end of last
conversion period. The operation is initiated by the falling edge of CS or the rising edge of FS.
19
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
start of operation cycle (continued)
CS initiates the operation: If FS is high at the falling edge of CS, the falling edge of CS initiates the operation.
When CS is high, SDO is in high-impedance state, the signals on SDI are ignored, and SCLK is disabled to clock
the serial data. The falling edge of CS resets the internal 4-bit counter and enables SDO, SDI, and SCLK. The
MSB of the input data via SDI, ID(15), is latched at the first falling edge of SCLK following the falling edge of
CS. The MSB of output data from SDO, OD(15), is valid before this SCLK falling edge. This mode works as an
SPI interface when CS is used as SLAVE SELECT (SS). It also can be used as normal DSP interface if CS
connects to the frame sync output of the host DSP. FS must be tied to high in this mode.
FS initiates the operation: If FS is low at the falling edge of CS, the rising edge of FS initiates the operation.
It resets the internal 4-bit counter, and enables SDI, SDO, and SCLK. The ID(15) is latched at the first falling
edge of SCLK following the falling edge of FS. OD(15) is valid before this falling edge of SCLK. This mode is
used to interface the converter with a serial port of the host DSP. The FS of the device is connected to the frame
sync of the host DSP. When several devices are connected to one DSP serial port, CS is used as chip select
to allow the host DSP to access each device individually. If only one converter is used, CS can be tied to low.
After the initiation, the remaining SDI data bits (if any) are shifted in and the remaining bits of SDO (if any) are
shifted out at the rising edge of SCLK. The input data are latched at the falling edge of SCLK, and the output
data are valid before the falling edge of SCLK. After the 4-bit counter reaches 16, the SDO goes to
high-impedance state. The output data from SDO is the previous conversion result in one shot conversion
mode, or the contents in the top of FIFO when FIFO is used (refer to Figure 20).
command period
After the rising edge of FS (FS triggers the operation) or the falling edge of CS (CS triggers the operation), SDI,
SDO, and SCLK are enabled. The first four SCLK clocks form the command period. The four MSBs of input data,
ID[15:12], are shifted in and decoded. These bits represent one of the 4-bit commands from the host, which
defines the required operation (see Table 1). The four MSB of output, OD[15:12], are also shifted out via SDO
during this period.
The commands are SELECT/CONVERSION, WRITE CFR, FIFO READ, and HARDWARE DEFAULT. The
SELECT/CONVERSION command includes SELECT ANALOG INPUT and SELECT TEST commands. All
cause a select/conversion operation. They select the analog signal being converted, and start the
sampling/conversion process after the selection. WRITE CFR causes the configuration operation, which writes
the device configuration information into CFR register. FIFO READ reads the contents in FIFO. Hardware
default mode sets the device into the hardware default mode.
After the command period, the remaining 12 bits of SDI are written into the CFR register to configure the device
if the command is WRITE CFR. Otherwise, these bits are ignored. The configuration is retained in the
autopower-down state. If the SCLK stops (while CS remains low) after the first eight bits are entered, the next
eight bits can be entered after the SCLK resumes. The data on SDI are ignored after the 4-bit counter counts
to 16 (falling edge of SCLK) or the low-to-high transition of CS, whichever happens first.
The remaining 12 bits of output data are shifted out from SDO if the command is SELECT/CONVERSION or
FIFO READ. Otherwise, the data on SDO must be ignored. In any case, the SDO goes into high-impedance
state after the 4-bit counter counts to 16 (falling edge of SCLK) or the low-to-high transition of CS, whichever
happens first.
20
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
command period (continued)
Table 1. Command Set (CMR)
SDI Bit D[15:12]
TLC3578 / 2578 COMMAND
TLC3574 / 2574 COMMAND
BINARY
0000b
0001b
0010b
0011b
0100b
0101b
0110b
0111b
1000b
1001b
1010b
1011b
1100b
1101b
1110b
1111b
HEX
0h
1h
2h
3h
4h
5h
6h
7h
8h
9h
Ah
Bh
Ch
Dh
Eh
Fh
SELECT analog input channel 0
SELECT analog input channel 1
SELECT analog input channel 2
SELECT analog input channel 3
SELECT analog input channel 4
SELECT analog input channel 5
SELECT analog input channel 6
SELECT analog input channel 7
Reserved
SELECT analog input channel 0
SELECT analog input channel 1
SELECT analog input channel 2
SELECT analog input channel 3
SELECT analog input channel 0
SELECT analog input channel 1
SELECT analog input channel 2
SELECT analog input channel 3
Reserved
WRITE CFR, the last 12 bits of SDI are written into CFR. This command resets FIFO.
SELECT TEST, voltage = (REFP+REFM)/2 (see Note 15)
SELECT TEST, voltage = REFM (see Note 16)
SELECT TEST, voltage = REFP (see Note 17)
FIFO READ, FIFO contents is shown on SDO; (see Note 18)
HARDWARE DEFAULT mode, CFR is loaded with 800h
NOTES: 15. The output code = mid-scale code + bipolar zero error
16. The output code = negative full-scale code + negative full-scale error
17. The output code = positive full-scale code + positive full-scale error
18. The TLC3574 and TLC3578, OD [15:2] is conversion result, OD [1:0] don’t care
The TLC2574 and TLC2578, OD [15:4] is conversion result, OD [3:0] don’t care
21
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
detailed description (continued)
Table 2. Configuration Register (CFR) Bit Definition
SDI BIT
D11
DEFINITION
Always 1. Otherwise the performance is degraded.
D10
Conversion output code format select:
0: BOB (bipolar offset binary);
1: BTC (binary 2s complement)
D9
Sample period select for normal sampling. Don’t care in extended sampling.
0: Long sampling (4x) 44 SCLKs;
1: Short sampling 12 SCLKs
D8
D7
Conversion clock source select:
0: Conversion clock = Internal OSC;
1: Conversion clock = SCLK/4
Input mode select:
0: Single-ended;
1: Pseudodifferential. Pin configuration shown below.
Pin Configuration of TLC3578 and TLC2578
Pin No. Single-ended Pseudodifferential polarity
Pin Configuration of TLC3574 and TLC2574
Pin No.
Single-ended Pseudodifferential polarity
9
10
A0
A1
Plus
Minus
Pair A
Pair B
Pair C
Pair D
9
10
A0
A1
PLUS
MINUS
Pair A
11
12
A2
A3
Plus
Minus
11
12
A2
A3
PLUS
MINUS
Pair B
13
14
A4
A5
Plus
Minus
15
16
A6
A7
Plus
Minus
D[6:5]
D[4:3]
Conversion mode select
00: One shot mode
01: Repeat mode
10: Sweep mode
11: Repeat sweep mode.
Sweep auto sequence select (Note: These bits only take effect in conversion mode 10 and 11.)
TLC3578 and TLC2578 TLC3574 and TLC2574
Single-ended (by ch) Pseudodifferential (by pair) Pseudodifferential (by pair)
00: N/A 00: N/A
01: A−B−A−B−A−B−A−B
10: N/A
11: A−A−A−A−B−B−B−B
Single-ended (by ch)
00: 0−1−2−3−4−5−6−7
01: 0−2−4−6−0−2−4−6
10: 0−0−2−2−4−4−6−6
11: 0−2−0−2−0−2−0−2
00: 0−1−2−3−0−1−2−3
01: 0−2−0−2−0−2−0−2
10: 0−0−1−1−2−2−3−3
11: 0−0−0−0−2−2−2−2
01: A−B−C−D−A−B−C−D
10: A−A−B−B−C−C−D−D
11: A−B−A−B−A−B−A−B
D2
EOC/INT pin function select
0: Pin used as INT
1: Pin used as EOC ( for mode 00 only)
D[1:0]
FIFO trigger level (sweep sequence length). Don’t care in one shot mode.
00: Full (INT generated after FIFO Level 7 filled)
01: 3/4 (INT generated after FIFO Level 5 filled)
10: 1/2 (INT generated after FIFO Level 3 filled)
11: 1/4 (INT generated after FIFO Level 1 filled)
sampling period
The sampling period follows the command period. The selected signal is sampled during this time. The device
has three different sampling modes: normal short mode, normal long mode, and extended mode.
Normal Short Sampling Mode: Sampling time is controlled by the SCLK and lasts 12 SCLK periods. At the
end of sampling, the converter automatically starts the conversion period. After the configuration, the normal
sampling starts automatically after the falling edge of fourth SCLK that follows the falling edge of CS if CS
triggers the operation, or follows the rising edge of FS if FS initiates the operation, except the FIFO READ and
WRITE CFR commands.
22
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
sampling period (continued)
Normal Long Sampling Mode: It is the same as normal short sampling, except that it lasts 44 SCLKs periods
to complete the sampling.
Extended Sampling Mode: The external signal, CSTART, triggers sampling and conversion. SCLK is not used
for sampling. SCLK is also not needed for conversion if the internal conversion clock is selected. The falling edge
of CSTART begins the sampling of the selected analog input. The sampling continues while CSTART is low.
The rising edge of CSTART ends the sampling, and starts the conversion (with about 15 ns internal delay). The
occurrence of CSTART is independent of SCLK clock, CS, and FS. However, the first CSTART cannot occur
before the rising edge of the 11th SCLK. In other words, the falling edge of first CSTART can happen at or after
the rising edge of 11th SCLK , but not before. The device enters the extended sampling mode at the falling edge
of CSTART and exits this mode once CSTART goes to high followed by two consecutive falling edges of CS
or two consecutive rising edges of FS (such as one read data operations followed by WRITE CFR). The first
CS or FS does not cause conversion. Extended mode is used when a fast SCLK is not suitable for sampling,
or when extended sampling period is needed to accommodate different input signal source impedance.
conversion period
The conversion period is the third portion of the operation cycle. It begins after the falling edge of 16th SCLK
for the normal short sampling mode, or after the falling edge of 48th SCLK for the normal long sampling, or on
the rising edge of CSTART (with 15 ns internal delay) for the extended sampling mode.
The conversion takes 18 conversion clocks plus 15 ns for TLC3574/78, 13 conversion clocks plus 15 ns for the
TLC2574/78. The conversion clock source can be an internal oscillator, OSC, or an external clock, SCLK. The
conversion clock is equal to the internal OSC if the internal clock is used, or equal to four SCLKs when the
external clock is programmed. To avoid the premature termination of conversion, enough time for the conversion
must be allowed between consecutive triggers. EOC goes to low at the beginning of the conversion period and
goes to high at the end of the conversion period. INT goes to low at the end of this period, too.
conversion mode
Four different conversion modes (mode 00, 01, 10, 11) are available. The operation of each mode is slightly
different, depending on how the converter samples and what host interface is used. Do not mix different types
of triggers throughout the repeat or sweep operations.
ONE SHOT Mode (Mode 00): Each operation cycle performs one sampling and one conversion for the selected
channel. FIFO is not used. When EOC is selected, it is generated while the conversion period is in progress.
Otherwise, INT is generated after the conversion is done. The result is output through the SDO pin during the
next select/conversion operation.
REPEAT Mode (Mode 01): Each operation cycle performs multiple samplings and conversions for a fixed
channel selected according to the 4-bit command. The results are stored in the FIFO. The number of samples
to be taken equals the FIFO threshold programmed via D[1:0] in CFR register. Once the threshold is reached,
INT is generated, and the operation ends. If the FIFO is not read after the conversions, the data is replaced in
the next operation. The operation of this mode starts with the WRITE CFR commands to set conversion mode
01, then the SELECT/CONVERSION commands, followed by a number of samplings and conversions of the
fixed channel (triggered by CS, FS, or CSTART) until the FIFO threshold is hit. If CS or FS triggers the sampling,
the data on SDI must be any one of the SELECT CHANNEL commands. However, this data is a dummy code
for setting the converter in conversion state. It does not change the existing channel selection set at the start
of the operation until the FIFO is full. After the operation finishes, the host can read the FIFO, then reselect the
channel and start the next REPEAT operation again; or immediately reselect the channel and start next REPEAT
operation (by issuing CS or FS or CSTART); or reconfigure the converter then start new operation according
to the new setting. If CSTART triggers the sampling, host can also immediately start the next REPEAT operation
(on the current channel) after the FIFO is full. Besides, if FS initiates the operation and CSTART triggers the
samplings and conversions, CS must not toggle during the conversion. This mode allows the host to set up the
converter, continue monitoring a fixed input, and to get a set of samples as needed.
23
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
conversion mode (continued)
SWEEP Mode (Mode 10): During each operation, all of the channels listed in the SWEEP SEQUENCE (D[4:3]
of CFR register) are sampled and converted one time according to the programmed sequence. The results are
stored in the FIFO. When the FIFO threshold is reached, an interrupt (INT) is generated, and the operation ends.
If the FIFO threshold is reached before all of the listed channels are visited, the remaining channels are ignored.
This allows the host to change the sweep sequence length. The mode 10 operation starts with the WRITE CFR
command to set the sweep sequence. The following triggers (CS, FS, or CSTART, depending on the interface)
start the samplings and conversions of the listed channels in sequence until the FIFO threshold is hit. If CS or
FS starts the sampling, the SDI data must be any one of the SELECT commands to set the converter in
conversion state. However, this command is a dummy code. It does not change the existing conversion
sequence. After the FIFO is full, the converter waits for FIFO READ. It does nothing before the FIFO READ or
WRITE CFR command is issued. The host must read the FIFO completely or WRITE CFR. If CSTART triggers
the samplings, the host must issue an extra SELECT/CONVERSION command (select any channel) via CS or
FS after the FIFO READ or WRITE CFR. This extra period is named the arm period and is used to set the
converter into conversion state, but does not affect the existing conversion sequence. If FS initiates the
operation and CSTART triggers the samplings and conversions, CS must not toggle during the conversion.
REPEAT SWEEP Mode (Mode 11): This mode works in the same way as mode 10, except that it is not
necessary to read the FIFO before the next operation after the FIFO threshold is hit. The next sweep can repeat
immediately, but the contents in the FIFO are replaced by the new results. The host can read the FIFO
completely, then issue next SWEEP; or repeat the SWEEP immediately (with the existing sweep sequence) by
issuing sampling/conversion triggers (CS, FS or CSTART); or change the device setting with the WRITE CFR
command.
The memory effect of charge redistribution DAC exists when the mux switches from one channel to another.
This degrades the channel-to-channel isolation if the channel changes after each conversion. For example, in
mode 10 and 11, the isolation is about 70 dB for the sweep sequence 0-1-2-3-4. The memory effect can be
reduced by increasing the sampling time or using sweep sequence 0-0-2-2-4-4-6-6 and ignoring the first sample
of each channel.
24
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
operation cycle timing
‡
12 SCLKs for Short
44 SCLKs for Long
18 OSC for Internal OSC
CS Initiates
Operation
4 SCLKs
15 ns
72 SCLK for External Clock
†
t
t
t
t
(overhead)
(setup)
(sample)
(convert)
SDI
§
4-bit Command
12-bit CFR Data (Optional)
SDO
14-bit Data (Previous Conversion) 2-bit Don’t Care
Active CS (FS Is Tied to High)
CSTAR (For Extended Sampling) occurs at
or after the rising edge of eleventh SCLK
FS Initiates
Operation
Delay From
Low to FS High
CS
‡
12 SCLKs for Short
44 SCLKs for Long
18 OSC for Internal OSC
4 SCLKs
15 nS
72 SCLK for External Clock
†
†
t
t
t
t
t
(overhead)
(delay)
(setup)
(sample)
(convert)
4-bit Command
12-bit CFR Data (Optional)
SDI
§
SDO
14-bit Data (Previous Conversion)
2-bit Don’t Care
Active CS (CS Can Be Tied to Low)
CSTAR (For Extended Sampling) occurs at
or after the rising edge of eleventh SCLK
Active FS
†
‡
Non JEDEC terms used.
18 internal OSC or 72 SCLK for TLC3574 and TLC3578,
13 internal OSC or 52 SCLK for TLC2574 and TLC2578.
For TLC3574 and TLC3578, 14-bits are result of previous conversion, last two bits are don’t care. For TLC2574 and TLC2578, 12-bits are result
of previous conversion, last four bits are don’t care.
§
25
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
operation cycle timing (continued)
After the operation finished, the host has several choices. Table 3 summarizes of operation options.
Table 3. Operation Options
CONVERSION IS INITIATED BY
MODE
CS
FS
CSTART
00
1. Issue new Select/Read operation to
read data and start new conversion.
2. Reconfigure the device.
1. Issue new Select/Read operation to
read data and start new conversion.
2. Reconfigure the device.
1. Issue new CSTART to start next
conversion; old data lost.
2. Issue new Select/Read operation to
read data—Issue new CSTART to
start new conversion.
3. Reconfigure the device.
01
1. Read FIFO—Select Channel—Start
new conversion. Channel must be
selected after FIFO READ.
1. Read FIFO—Select Channel—Start
new conversion. Channel must be
selected after FIFO READ.
1. Read FIFO—Select channel—Start
new conversion. Channel must be
selected after FIFO READ.
2. Select Channel—Start new
conversion (old data lost)
2. Select Channel—Start new
conversion (old data lost)
2. Start new conversion (old data lost)
with existing setting.
3. Configure device again.
3. Configure device again.
3. Configure device again.
10
11
1. Read FIFO—Start new conversion
with existing setting.
2. Configure device—New conversion
(old data lost)
1. Read FIFO—Start new conversion
with existing setting.
2. Configure device—New conversion
(old data lost)
1. Read FIFO—Arm Period—Start new
conversion with existing setting
2. Configure device—Arm Period—New
conversion (old data lost)
1. Read FIFO—Start new conversion
with existing setting.
1. Read FIFO—Start new conversion
with existing setting
1. Read FIFO—Arm Period—Start new
Conversion with existing setting
2. Start new conversion with the existing 2. Start new conversion with the existing 2. Start new conversion with existing
setting.
setting.
setting. (old data lost)
3. Configure device—Start new
conversion with new setting.
3. Configure Device—Start new
conversion with new setting.
3. Configure device—Arm Period—New
conversion with new setting.
operation timing diagrams
The nonconversion operation includes FIFO READ and WRITE CFR. Both do not perform a conversion. The
conversion operation performs one of four types of conversion: mode 00, 01, 10 and 11
write cycle (WRITE CFR Command): Write cycle does not generate EOC or INT, nor does it carry out any
conversion.
1
1
7
3
4
12
13
14
15
16
2
5
6
CS
FS
ID15 1D14 ID13 1D12 ID11 ID10 ID9
ID4
ID3
ID2
ID1
ID0
ID15
SDI
INT
OR
EOC
SDO
Hi-Z
The dotted lines means signal may or may not exist.
Don’t care
Figure 8. Write Cycle, FS Initiates Operation
26
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ
ꢚꢛ
ꢒ
ꢌ
ꢁ
ꢌ
ꢍ
ꢌ
ꢁꢎ
ꢏ
ꢊ
ꢀꢎ
ꢊ
ꢑ
ꢒ
ꢏ
ꢒ
ꢀꢌ
ꢁ
ꢂ
ꢎ
ꢍ
ꢋ
ꢚ
ꢛ
ꢀ
ꢚ
ꢛ
ꢗ
ꢜ
ꢒ
ꢀ
ꢙ
ꢓ
ꢕ
ꢊ
ꢋ
ꢒ
ꢍ
ꢘ
ꢝ
ꢀ
ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
operation timing diagrams (continued)
1
2
3
4
5
6
12
13
15
16
7
14
1
CS
FS = High
SDI
ID15 1D14 ID13 1D12 ID11 ID10 ID9
ID4
ID3
ID2
ID1
ID0
ID15 ID14
INT
OR
EOC
SDO
Hi-Z
The dotted lines means signal may or may not exist.
Don’t Care
Figure 9. Write Cycle, CS Initiates Operation, FS = 1
FIFO READ Operation: When the FIFO is used, the first command after INT is generated is assumed to be
the FIFO READ. The first FIFO content is output immediately before the command is decoded. If this command
is not FIFO READ, the output is terminated. Using more layers of FIFO reduces the time taken to read multiple
conversion results, because the read cycle does not generate an EOC or INT, nor does it make a data
conversion. Once the FIFO is read, the entire contents in FIFO must be read out. Otherwise, the remaining data
is lost.
1
2
3
4
6
7
12
13
16
5
14
15
1
SCLK
CS
FS = High
SDI
ID15 1D14 ID13 1D12
ID15 ID14
INT
OR
EOC
SDO
Hi-Z
OD15 OD14 OD13 OD12 OD11 OD10 OD9
OD4 OD3 OD2
OD15 OD14
The dotted lines means signal may or may not exist.
OD[15:2] (for TLC3574/78) or OD[15:4](for TLC2574/78) is the FIFO content.
Don’t Care
Figure 10. FIFO Read Cycle, CS Initiates Operation, FS = 1
27
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢓ
ꢄ
ꢊ
ꢋ
ꢌ
ꢍ
ꢌꢁ
ꢎ
ꢏ
ꢇ
ꢃ
ꢊ
ꢐ
ꢄ
ꢊ
ꢋ
ꢑ
ꢒ
ꢏ
ꢒ
ꢀꢌ
ꢁ
ꢇ
ꢓ
ꢆ
ꢊ
ꢐ
ꢉꢊ
ꢔ
ꢒ
ꢀꢇ
ꢉ
ꢕ
ꢕ
ꢊ
ꢖ
ꢗ
ꢘ
ꢗ
ꢇ
ꢆ
ꢊ
ꢐ
ꢈ
ꢊ
ꢂ
ꢙ
ꢌ
ꢍ
ꢍ
ꢚ
ꢁ
ꢗ
ꢚ
ꢛ
ꢒ
ꢌ
ꢁ
ꢌ
ꢍ
ꢌ
ꢁ
ꢎ
ꢏ
ꢊ
ꢀ
ꢎ
ꢊ
ꢑ
ꢒ
ꢏ
ꢒ
ꢀ
ꢌ
ꢁ
ꢂ
ꢎ
ꢍ
ꢋ
ꢚ
ꢛꢀ
ꢚ
ꢛ
ꢗ
ꢜ
ꢒ
ꢀ
ꢙ
ꢓ
ꢕ
ꢊ
ꢋ
ꢒ
ꢍ
ꢘ
ꢝ
ꢀ
ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
conversion operation
48 SCLKs for Long Sampling
16 SCLKs for Short Sampling
1
12
13
16
1
2
3
4
5
6
7
14
15
CS
FS in High
SDI
Select Channel
ID15
ID14 ID13 1D12
ID15
INT
t
(SAMPLE)
t(conv)
EOC
SDO
Previous Conversion Result
OR
Hi−Z
OD2
OD15
OD15 OD14 OD13 OD12 OD11 OD10 OD9
OD4
OD3
SDO goes to Hi−Z after 16th SCLK
The dotted line means signal may or may not exist.
OD[15:2] (for TLC3574/78) or OD [15:4] (for TLC2574/78) is the result of previous conversion.
Don’t Care
Figure 11. Mode 00, CS Initiates Operation
48 SCLKs for Long Sampling
16 SCLKs for Short Sampling
1
1
2
3
4
5
6
7
12
13 14 15
16
SCLK
CS
FS
Select Channel
SDI
INT
ID15 1D14 ID13 1D12
ID15
t
t
(conv)
(SAMPLE)
OR
EOC
SDO
Previous Conversion Result
SDO Goes Through Hi-Z After 16 SCLK
Hi-Z
OD15
OD14 OD13 OD12 OD11 OD10 OD9
OD4 OD3 OD2
OD15
The dotted line means signal may or may not exist.
OD[15:2] (for TLC3574/78) or OD[15:4](for TLC2574/78) is the result of previous conversion.
Don’t Care
Figure 12. Mode 00, FS Initiates Operation
28
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
conversion operation (continued)
Select Channel
16 SCLK
Select Channel
16 SCLK
t
(sample)
CS Tied to Low
CSTART
Possible
Signal
t
(convert)
FS
**
**
SDI
INT
EOC
SDO
**
Data Lost
Previous Conversion Result
Hi-Z
Conversion Result
Hi-Z
OR
Hi-Z
Possible Signal
Select Channel
Don’t Care
Figure 13. Mode 00, CSTART Triggers Sampling/Conversion, FS Initiates Select
CS
FS
Select Any
Channel
Select Any
Channel
Select CH1
Select CH2
SDI
***
**
**
*
*
**
**
*
*
DATA1 of CH1 DATA2 of CH1
DATA1 of CH2 DATA2 of CH2
Hi-Z
SDO
INT
1/4 FIFO FULL
1/4 FIFO FULL
Don’t Care
Possible Signal
*** −− WRITE CFR
MODE 01, FS Activates Conversion, FIFO Threshold = 1/4 Full
Read FIFO After Threshold Is Hit
**
*
−− Select Channel
−− FIFO Read
Figure 14. Mode 01, FS Initiates Operations
CS
FS
CSTART
SDI
Select CH1
**
Select CH2
**
***
*
*
*
*
DATA1 of CH1 DATA2 of CH1
DATA1 of CH2 DATA2 of CH2
Hi-Z
SDO
INT
1/4 FIFO FULL
1/4 FIFO FULL
Don’t Care
MODE 01, FS Initiates Select Period, CSTART Activates Conversion, FIFO Threshold = 1/4 Full,
Read FIFO After Threshold Is Hit
Possible Signal
*** −− WRITE CFR
**
*
−− Select Channel
−− FIFO Read
Figure 15. Mode 01, CSTART Triggers Samplings/Conversions
29
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ
ꢚ
ꢛ
ꢒ
ꢌ
ꢁ
ꢌ
ꢍ
ꢌ
ꢁ
ꢎ
ꢏ
ꢊ
ꢀ
ꢎ
ꢊ
ꢑ
ꢒ
ꢏ
ꢒ
ꢀ
ꢌ
ꢁ
ꢂ
ꢎ
ꢍ
ꢋ
ꢚ
ꢛꢀ
ꢚ
ꢛ
ꢗ
ꢜ
ꢒ
ꢀ
ꢙ
ꢓ
ꢕ
ꢊ
ꢋ
ꢒ
ꢍ
ꢘ
ꢝ
ꢀ
ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
conversion operation (continued)
Conversion
From CH0
Conversion
From CH3
Conversion
From CH0
Conversion
From CH3
Configure
CS
FS
**
**
**
**
**
**
**
**
***
*
*
*
*
*
SDI
INT
Hi-Z
1st Sweep
CH0
CH0
CH1
CH2
CH3
SDO
2nd Sweep
Using Existing
Configuration
Don’t Care
1st FIFO Read
Read FIFO After FIFO Threshold Is Hit
2nd FIFO Read
*** Command = Configure Write for Mode 10, FIFO
Threshold = 1/2 Full, Sweep Sequence: 0−1−2−3
** COMMAND = Select Any Channel
*
COMMAND = Read FIFO
Figure 16. Mode 10, FS Initiates Operations
Conversion
From CH0
Conversion
From CH2
Conversion
From CH0
Conversion
From CH2
Configure
CS Tied
to Low
FS
CSTART
*** **
*
*
*
*
**
*
SDI
INT
Hi-Z
CH0
CH0
CH2
CH2
CH0
SDO
2nd Sweep
Using Existing
Configuration
1st Sweep
Don’t Care
2nd FIFO Read
1st FIFO Read
Read FIFO After FIFO Threshold Is Hit, FS Initiates Select Period
*** Command = Configure Write for Mode 10, FIFO
Threshold = 1/2 Full, Sweep Sequence: 0−0−2−2
** COMMAND = Select Any Channel
*
COMMAND = Read FIFO
Figure 17. Mode 10, CSTART Initiates Operations
Conversion
From CH0
Conversion Conversion
From CH3 From CH0
Conversion
From CH3
Conversion
From CH0
Configure
CS
START 2nd Round SWEEP CONVERSION,
the DATA of the 1st Round Are Lost
FS=High
***
**
**
**
**
**
**
**
**
*
*
*
*
**
SDI
INT
CH0
CH1
CH2
CH3
SDO
READ the DATA of 2nd
Sweep From FIFO
Don’t Care
*** Command = Configure Write for Mode 11, FIFO
Threshold = 1/2 Full, Sweep Sequence: 0−1−2−3
** COMMAND = Select Any Channel
START 2nd Sweep conversion immediately (NO FIFO READ) after the 1st SWEEP completed.
*
COMMAND = Read FIFO
Figure 18. Mode 11, CS Initiates Operations
30
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ
ꢚꢛ
ꢒ
ꢌ
ꢁ
ꢌ
ꢍ
ꢌ
ꢁꢎ
ꢏ
ꢊ
ꢀꢎ
ꢊ
ꢑ
ꢒ
ꢏ
ꢒ
ꢀꢌ
ꢁ
ꢂ
ꢎ
ꢍ
ꢋ
ꢚ
ꢛ
ꢀ
ꢚ
ꢛ
ꢗ
ꢜ
ꢒ
ꢀ
ꢙ
ꢓ
ꢕ
ꢊ
ꢋ
ꢒ
ꢍ
ꢘ
ꢝ
ꢀ
ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
conversion operation (continued)
Conversion
From CH0
Conversion
From CH2
Conversion
From CH0
Conversion
From CH2
Configure
CS
FS
CSTART
*** **
*
*
*
*
**
*
SDI
INT
1st SWEEP
REPEAT
CH0
CH0
1st FIFO Read
READ FIFO after 1st SWEEP Completed
CH2
CH2
CH0
SDO
2nd FIFO Read
Don’t Care
*** Command = Configure Write for Mode 11, FIFO
Threshold = 1/2 Full, Sweep Sequence: 0−0−2−2
** COMMAND = Select Any Channel
*
COMMAND = Read FIFO
Possible Signal
Figure 19. Mode 11, CSTART Triggers Samplings/Conversions, FS Initiates SELECT Operation
conversion clock and conversion speed
The conversion clock source can be the internal OSC, or the external clock, SCLK. The conversion clock is equal
to the internal OSC if the internal clock is used, or equal to SCLK/4 when the external clock is selected. It takes
18 conversion clocks plus 15 ns to finish the conversion for TLC3574 and TLC3578, and 13 conversion clocks
plus 15 ns for the TLC2574 and TLC2578. If the external clock is selected, the conversion time (not including
sampling time) is 18X(4/f
)+15 ns for TLC3574 and TLC3578 and 13X(4/f
)+15 ns for TLC2574 and
SCLK
SCLK
TLC2578. Table 4 shows the maximum conversion rate (including sampling time) when the analog input source
resistor is 25 Ω.
Table 4. Maximum Conversion Rate
MAX SCLK
(MHz)
CONVERSION
TIME (µs)
RATE
(KSPS)
DEVICE
SAMPLING MODE
CONVERSION CLK
SHORT (16 SCLK)
LONG (48 SCLK)
SHORT (16 SCLK)
LONG (48 SCLK)
SHORT (16 SCLK)
LONG (48 SCLK)
SHORT (16 SCLK)
LONG (48 SCLK)
External SCLK/4
External SCLK/4
Internal 6.5 MHz
Internal 6.5 MHz
Exernal SCLK/4
External SCLK/4
Internal 6.5 MHz
Internal 6.5 MHz
10
25
10
25
10
25
10
25
8.815
4.815
4.384
4.705
6.815
4.015
3.615
3.935
113.4
207.7
228.0
212.5
146.7
249.1
276.6
254.1
TLC3574/78
(Rs = 25 Ω)
TLC2574/78
(Rs = 25 Ω)
31
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ
ꢚ
ꢛ
ꢒ
ꢌ
ꢁ
ꢌ
ꢍ
ꢌ
ꢁ
ꢎ
ꢏ
ꢊ
ꢀ
ꢎ
ꢊ
ꢑ
ꢒ
ꢏ
ꢒ
ꢀ
ꢌ
ꢁ
ꢂ
ꢎ
ꢍ
ꢋ
ꢚ
ꢛꢀ
ꢚ
ꢛ
ꢗ
ꢜ
ꢒ
ꢀ
ꢙ
ꢓ
ꢕ
ꢊ
ꢋ
ꢒ
ꢍ
ꢘ
ꢝ
ꢀ
ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
FIFO operation
Serial
0
SOD
×8
FIFO
ADC
7
6
5
4
3
2
1
FIFO Full
FIFO 1/2 Full
FIFO 3/4 Full
FIFO 1/4 Full
FIFO Threshold Pointer
Figure 20. FIFO Structure
FIFO operation (continued)
The device has an 8-level FIFO that can be programmed for different thresholds. An interrupt is sent to the host
after the preprogrammed threshold is reached. The FIFO is used to store conversion results in mode 01, 10,
and 11, from either a fixed channel or a series of channels according to the preprogrammed sweep sequence.
For example, an application may require eight measurements from channel 3. In this case, if the threshold is
set to full, the FIFO is filled with 8 data conversions sequentially taken from channel 3. Another application may
require data from channel 0, 2, 4, and 6 in that order. The threshold is set to 1/2 full and sweep sequence is
selected as 0−2−4−6−0−2−4−6. An interrupt is sent to the host as soon as all four data conversions are in the
FIFO. FIFO is reset after power on and WRITE CFR operation. The contents of the FIFO are retained during
autopower down.
Autopower-Down Mode: The device enters the autopower-down state at the end of conversion. The power
current is about 20 µA if SCLK stops, and 120 µA maximum if SCLK is running. Active CS , FS, or CSTART
resumes the device from power-down state. The bipolar input current is not turned off when device is in
power-down mode.
The configuration register is not affected by the power-down mode but the SWEEP operation sequence must
be started over again. All FIFO contents are retained in power-down mode.
32
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TYPICAL CHARACTERISTICS
INTEGRAL NONLINEARITY
vs
DIGITAL OUTPUT CODE
2
1.5
1
Reference = 4 V
AV = 5 V, T = 25°C
DD
A
0.5
0
−0.5
0
2000
4000
6000
8000
10000
12000
14000
16000
Digital Output Code
Figure 21
DIFFERENTIAL NONLINEARITY
vs
DIGITAL OUTPUT CODE
0.6
0.4
0.2
−0.0
−0.2
−0.4
−0.6
Reference = 4 V
AV = 5 V, T = 25°C
DD
A
0
2000
4000
6000
8000
10000
12000
14000
16000
Digital Output Code
Figure 22
33
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TYPICAL CHARACTERISTICS
BIPOLAR ZERO ERROR, POSITIVE FULL SCALE ERROR
AND NEGATIVE FULL SCALE ERROR (% FS)
vs
INL (LSB) AND DNL (LSB)
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
0.500
1.3
Reference = 4 V
Reference = 4 V
AV
DD
= 5 V
AV
DD
= 5 V
0.400
0.300
INL
1
Negative Full Scale Error
Positive Full Scale Error
0.7
0.200
0.100
DNL
Bipolar Zero Error
25
0.4
−40.00
−40.00
85
25
85
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 23
Figure 24
FFT OF SNR (dB)
0
Reference = 4 V
AV = 5 V
−20
DD
= 25°C
−40
T
A
−60
200 KSPS
Input Signal = 20 kHz, 0dB
−80
−100
−120
−140
−160
−180
0
24.4
48.8
73.2
97.7
f − Frequency − kHz
Figure 25
34
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TYPICAL CHARACTERISTICS
SINAD
vs
ENOB
vs
INPUT SIGNAL FREQUENCY
INPUT SIGNAL FREQUENCY
82
80
13.2
12.8
12.4
12
Reference = 4 V
Reference = 4 V
AV
DD
A
= 5 V
= 25°C
AV
DD
A
= 5 V
= 25°C
T
T
78
76
74
72
11.6
100 k
1 k
20 k
40 k
60 k
80 k
1 k
20 k
40 k
60 k
80 k
100 k
f − Input Signal Frequency − Hz
I
f − Input Signal Frequency − Hz
I
Figure 26
Figure 27
TOTAL HARMONIC DISTORTION
vs
SFDR
vs
INPUT SIGNAL FREQUENCY
INPUT SIGNAL FREQUENCY
−78
−80
85
83
81
Reference = 4 V
AV = 5 V
Reference = 4 V
AV = 5 V
DD
DD
T
= 25°C
A
T
= 25°C
A
−82
−84
79
77
1 k
20 k
40 k
60 k
80 k
100 k
1 k
20 k
40 k
60 k
80 k
100 k
f − Input Signal Frequency − Hz
I
f − Input Signal Frequency − Hz
I
Figure 28
Figure 29
35
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
SUPPLY CURRENT AT AUTOPOWER DOWN
vs
FREE-AIR TEMPERATURE
5.6
4
3
2
Reference = 4 V
Reference = 4 V
AV
= 5 V
SCLK Stops
DD
AV
DD
= 5 V
5.4
Autopower Down
5.2
5
−40.00
25
85
−40
25
85
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 30
Figure 31
36
WWW.TI.COM
ꢀ ꢁꢂ ꢃ ꢄ ꢅꢆ ꢇ ꢀ ꢁꢂ ꢃ ꢄ ꢅꢈ ꢇ ꢀ ꢁꢂ ꢉ ꢄ ꢅꢆ ꢇ ꢀꢁ ꢂꢉ ꢄꢅ ꢈ
ꢄ ꢊꢋ ꢌꢍ ꢌꢁ ꢎ ꢏꢇ ꢃ ꢊꢐꢄ ꢊꢋ ꢑꢒ ꢏꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐꢓ ꢉ ꢊꢔꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊ ꢂꢙ ꢌꢍ ꢍ ꢚꢁ
ꢗ ꢚꢛ ꢒ ꢌꢁ ꢌꢍꢌ ꢁꢎ ꢏ ꢊꢀꢎ ꢊꢑꢒꢏ ꢒ ꢀꢌꢁ ꢂꢎ ꢍꢋꢚ ꢛꢀ ꢚꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒ ꢍꢘ ꢝ ꢀꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
APPLICATION INFORMATION
interface with host
Figure 32 shows the examples of the interface between a single converter and host DSP (TMS320C54x DSP)
or microprocessor. The C54x is set as FWID=1 (active pulse width=1CLK); (R/X) DATDLY=1 (1 bit data delay);
CLK(X/R)P=0 (transmit data are clocked out at rising edge of CLK, receive data are sampled on falling edge
of CLK); and FS(X/R)P=1 (FS is active high). If multiple converters connect to the same C54x, use CS as chip
select.
The host microprocessor is set as the SPI master, CPOL=0 (active high clock), and CPHA=1 (transmit data is
clock out at rising edge of CLK, receive data are sampled at falling edge of CLK). 16 bits (or more) per transfer
is required.
V
DD
V
DD
10 kΩ
10 kΩ
10 kΩ
TMS320C54X
FSR
Converter
CS
Host
Microprocessor
Converter
SS
CS
FSX
DX
FS
FS
Ain
Ain
SDI
SDO
MOSI
MISO
SDI
SDO
DR
CLKR
SCLK
SCLK
CLKX
IRQ
SCK
IRQ
INT/EOC
INT/EOC
Single Converter Connects to DSP
Converter Connects to Microprocessor
Figure 32. Typical Interface to Host DSP and Microprocessor
sampling time analysis
Figure 33 shows the equivalent circuit to evaluate the required sampling time. Req is the Thevenin equivalent
resistor (Req = 3.5 K). The C is sampling capacitor (30 pF maximum).
(sampling)
To get 1/4 LSB accuracy, the sampling capacitor, C
, has to be charged to
sampling
V = V
voltage of 1/4 LSB = V
(V /65532) for 14 bit converter (TLC3574 and TLC3578)
S
C
S
S
S
= V
(V /16384) for 12 bit converter (TLC2574 and TLC2578)
S
During the sampling time t
, C
is charge to
(sampling) (sampling)
–t
ȱ
ȳ
ȴ
(sampling)
V
+ V 1–exp
ǒ Ǔȧ
Sȧ
C
Req C
(sampling)
Ȳ
Therefore, the required sampling time is
t
t
= Req × C
= Req × C
× In (65532) for 14-bit (TLC3574 and TLC3578)
× In (16384) for 12-bit (TLC2574 and TLC2578).
(sampling)
(sampling)
(sampling)
(sampling)
TMS320C54x is a trademark of Texas Instruments.
37
WWW.TI.COM
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢇ ꢀ ꢁ ꢂ ꢃꢄ ꢅꢈ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢆ ꢇ ꢀꢁ ꢂꢉ ꢄ ꢅ ꢈ
ꢄꢊ ꢋ ꢌ ꢍ ꢌꢁ ꢎꢏꢇ ꢃ ꢊꢐ ꢄ ꢊꢋ ꢑꢒ ꢏ ꢒ ꢀꢌꢁ ꢇ ꢓ ꢆ ꢊꢐ ꢓ ꢉꢊꢔ ꢒ ꢀꢇ ꢉ ꢕ ꢕ ꢊꢖꢗꢘ ꢗꢇ ꢆ ꢊꢐꢈ ꢊꢂꢙ ꢌꢍꢍꢚ ꢁ
ꢗ ꢚꢛꢒ ꢌ ꢁ ꢌ ꢍ ꢌꢁ ꢎꢏ ꢊꢀꢎ ꢊꢑꢒ ꢏ ꢒꢀꢌꢁ ꢂꢎ ꢍꢋ ꢚ ꢛꢀ ꢚ ꢛꢗ ꢜ ꢒꢀ ꢙ ꢓ ꢕ ꢊꢋ ꢒꢍ ꢘꢝꢀ ꢗ
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
APPLICATION INFORMATION
REFP
Bipolar Signal
Scaling
MUX
Req
3.94 kΩ
1.5 kΩ Max
Ain
9.9 kΩ
Converter
Vs
R
on
C
(sample)
= 30 pF Max
6.6 kΩ
C
(sample)
= 30 pF
Req = Thevenin Equivalent Resistance
Vs = Thevenin Equivalent Voltage
REFM
Figure 33. Equivalent Input Circuit Including the Driving Source
38
WWW.TI.COM
PACKAGE OPTION ADDENDUM
www.ti.com
6-Oct-2008
PACKAGING INFORMATION
Orderable Device
TLC2574IDW
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SOIC
DW
20
20
20
20
24
24
24
24
24
24
20
20
20
20
20
20
24
24
24
24
24
24
24
24
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TLC2574IDWG4
TLC2574IPW
SOIC
TSSOP
TSSOP
SOIC
DW
PW
PW
DW
DW
PW
PW
PW
PW
DW
DW
DW
DW
PW
PW
DW
DW
DW
DW
PW
PW
PW
PW
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TLC2574IPWG4
TLC2578IDW
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TLC2578IDWG4
TLC2578IPW
SOIC
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
SOIC
60 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TLC2578IPWG4
TLC2578IPWR
TLC2578IPWRG4
TLC3574IDW
60 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TLC3574IDWG4
TLC3574IDWR
TLC3574IDWRG4
TLC3574IPW
SOIC
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TSSOP
SOIC
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TLC3574IPWG4
TLC3578IDW
70 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TLC3578IDWG4
TLC3578IDWR
TLC3578IDWRG4
TLC3578IPW
SOIC
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
60 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TLC3578IPWG4
TLC3578IPWR
TLC3578IPWRG4
60 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
6-Oct-2008
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLC2578IPWR
TLC3574IDWR
TLC3578IPWR
TSSOP
SOIC
PW
DW
PW
24
20
24
2000
2000
2000
330.0
330.0
330.0
16.4
24.4
16.4
6.95
10.8
6.95
8.3
13.3
8.3
1.6
2.7
1.6
8.0
12.0
8.0
16.0
24.0
16.0
Q1
Q1
Q1
TSSOP
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLC2578IPWR
TLC3574IDWR
TLC3578IPWR
TSSOP
SOIC
PW
DW
PW
24
20
24
2000
2000
2000
367.0
367.0
367.0
367.0
367.0
367.0
38.0
45.0
38.0
TSSOP
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
TLC3574INE4
4-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20, PLASTIC, MS-001AD, DIP-20
TI
TLC3574IPW
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
TLC3574IPWG4
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
TLC3574IPWR
IC 4-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20, GREEN, PLASTIC, TSSOP-20, Analog to Digital Converter
TI
TLC3578
5-V ANALOG 3-/5-V DIGITAL 14-/12-BIT 200-KSPS 4-/8-CHANNEL SERIAL ANALOG TO DIGITAL CONVERTERS WITH 10-V INPUTS
TI
TLC3578IDW
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
TLC3578IDWG4
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
TLC3578IDWR
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
TLC3578IDWRG4
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
TLC3578IPW
5-V ANALOG 3-5V DIGITAL 14-12BIT 200-KSPS 4-8CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH
TI
©2020 ICPDF网 联系我们和版权申明