TLE2072AQDRG4Q1 [TI]
EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS; EXCALIBUR低噪声高速JFET输入运算放大器
| 型号： | TLE2072AQDRG4Q1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS |
| 文件： | 总42页 (文件大小：692K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226B − DECEMBER 2003 − REVISED MAY 2008
D
D
D
Qualified for Automotive Applications
D
D
D
Ensured Maximum Noise Floor
17 nV/√Hz
On-Chip Offset Voltage Trimming for
Improved DC Performance
Direct Upgrades to TL05x, TL07x, and
TL08x BiFET Operational Amplifiers
Greater Than 2× Bandwidth (10 MHz) and
3× Slew Rate (45 V/µs) Than TL07x
Wider Supply Rails Increase Dynamic
Signal Range to 19 V
description/ordering information
The TLE207x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew
rate of the TL07x and TL08x families of BiFET operational amplifiers. Texas Instruments Excalibur process
yields a typical noise floor of 11.6 nV/√Hz, 17-nV/√Hz ensured maximum, offering immediate improvement in
noise-sensitive circuits designed using the TL07x. The TLE207x also has wider supply voltage rails, increasing
the dynamic signal range for BiFET circuits to 19 V. On-chip zener trimming of offset voltage yields precision
grades for greater accuracy in dc-coupled applications. The TLE207x are pin-compatible with lower
performance BiFET operational amplifiers for ease in improving performance in existing designs.
BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without
sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with
high-impedance sensors or very low-level ac signals. They also feature inherently better ac response than
bipolar or CMOS devices having comparable power consumption.
The TLE207x family of BiFET amplifiers are Texas Instruments highest performance BiFETs, with tighter input
offset voltage and ensured maximum noise specifications. Designers requiring less stringent specifications but
seeking the improved ac characteristics of the TLE207x should consider the TLE208x operational amplifier
family.
Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to
observe common-mode input voltage limits and output swing when operating from a single supply. DC biasing
of the input signal is required and loads should be terminated to a virtual ground node at mid-supply. Texas
Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from single
supplies.
ORDERING INFORMATION†
V
max
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
IO
‡
T
A
PACKAGE
AT 25°C
2 mV
SOIC − D
SOIC − D
SOIC − D
SOIC − D
SOP − DW
SOP − DW
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tape and reel
TLE2071AQDRQ1
TLE2071QDRQ1
TLE2072AQDRQ1
TLE2072QDRQ1
TLE2074AQDWRQ1
2071AQ
4 mV
2071Q1
3.5 mV
6 mV
2072AQ
−40°C to 125°C
2072Q1
§
4 mV
TLE2074AQ1
TLE2074Q1
§
7 mV
TLE2074QDWRQ1
†
For the most current package and ordering information, see the Package Option Addendum at the end of this
document, or see the TI web site at http://www.ti.com.
Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging.
Product Preview
‡
§
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2008, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226B − DECEMBER 2003 − REVISED MAY 2008
description/ordering information (continued)
The TLE207x are fully specified at 15 V and 5 V. For operation in low-voltage and/or single-supply systems,
Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended. When
moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth
requirements and output loading.
TLE2071 AND TLE2071A
D PACKAGE
TLE2072 AND TLE2072A
D PACKAGE
TLE2074 AND TLE2074A
DW PACKAGE
(TOP VIEW)
(TOP VIEW)
(TOP VIEW)
OFFSET N1
IN −
NC
VCC+
OUT
OFFSET N2
1OUT
1IN−
1IN +
VCC−
VCC+
2OUT
2IN−
2IN+
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
4OUT
4IN−
14 4IN+
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
NC
1
2
3
4
5
6
7
8
16
15
IN +
VCC−
13
12
11
10
9
VCC−
3IN+
3IN−
3OUT
NC
NC − No internal connection
symbol
+
−
IN+
IN−
OUT
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
equivalent schematic
V
CC+
R2
Q1
R1
R6
R11
Q11
Q17
Q3
Q8
Q23
D2
R3
Q28
Q20
C1
Q13
Q24
IN−
D3
Q12
R13
Q4
Q15
Q16
Q19
OUT
R12
IN+
Q30
Q9
R8
Q5
Q25
C6
C3
Q29
Q18
Q2
D1
Q6
Q7
Q14
Q21
Q22
Q26
Q27
Q10
C5
R9
R7
Q31
R14
R4
C2
R10
R5
C4
OFFSET N1
(see Note A)
V
CC−
OFFSET N2
(see Note A)
NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the TLE2071x devices.
equivalent schematic (continued)
ACTUAL DEVICE COMPONENT COUNT
COMPONENT
Transistors
Resistors
TLE2071
TLE2072
TLE2074
114
33
25
8
57
37
5
74
Diodes
10
Capacitors
6
11
22
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, V
Supply voltage, V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −19 V
CC+
CC−
Differential input voltage range, V (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
to V
to V
ID
CC+
CC−
Input voltage range, V (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
I
CC+
CC−
Input current, I (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 mA
I
Output current, I (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA
O
Total current into V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA
CC+
Total current out of V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA
CC−
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Maximum Junction Temperature, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
J
Package thermal impedance, θ (see Note 4): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126°C/W
JA
DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75°C/W
Operating free-air temperature range, T : Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
A
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 3 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between V
and V
.
CC+
CC−
2. Differential voltages are at the noninverting input with respect to the inverting input.
3. The output may be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum
dissipation rate is not exceeded.
4. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
MIN
2.25
−0.8
−10.8
−40
MAX
19
UNIT
Supply voltage, V
V
CC
V
V
=
=
5 V
5
CC
Common-mode input voltage, V
V
IC
15 V
15
CC
Operating free-air temperature, T
125
°C
A
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2071-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted)
=
5 V (unless
TLE2071-Q1
TLE2071A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
25°C
0.34
4
9
0.3
2
7
V
Input offset voltage
mV
IO
Full range
V
= 0,
V
= 0,
= 0,
IC
O
O
R = 50 Ω,
S
Temperature coefficient
of input offset voltage
20
α
VIO
Full range
3.2
5
3.2
5
µV/°C
25°C
Full range
25°C
100
20
100
20
pA
nA
pA
nA
I
IO
Input offset current
Input bias current
V
IC
= 0,
V
See Figure 4
15
175
60
15
175
60
I
IB
Full range
5
to
−1
5
to
−1.9
5
to
−1
5
to
−1.9
25°C
Common-mode input
voltage range
V
R
I
= 50 Ω
S
V
V
ICR
5
to
−0.8
5
to
−0.8
Full range
25°C
Full range
25°C
3.8
3.6
3.5
3.3
1.5
1.4
−3.8
−3.6
−3.5
−3.3
−1.5
−1.4
80
4.1
3.9
3.8
3.6
3.5
3.3
1.5
1.4
−3.8
−3.6
−3.5
−3.3
−1.5
−1.4
80
4.1
3.9
= −200 µA
= −2 mA
= −20 mA
= 200 µA
= 2 mA
O
Maximum positive peak
output voltage swing
V
OM+
I
O
I
O
I
O
I
O
I
O
Full range
25°C
2.3
2.3
Full range
25°C
−4.2
−4.1
−2.4
91
−4.2
−4.1
−2.4
91
Full range
25°C
Maximum negative peak
output voltage swing
V
A
V
OM−
Full range
25°C
= 20 mA
Full range
25°C
R = 600 Ω
L
Full range
25°C
78
78
90
100
106
90
100
106
Large-signal differential
voltage amplification
V
O
=
2.3 V R = 2 kΩ
dB
VD
L
Full range
25°C
88
88
95
95
R = 10 kΩ
L
Full range
25°C
93
93
12
12
Ω
r
Input resistance
V
V
= 0
10
10
i
IC
Common
mode
25°C
25°C
25°C
11
2.5
80
11
2.5
80
= 0,
IC
c
z
Input capacitance
pF
i
See Figure 5
Differential
Open-loop output
impedance
Ω
dB
dB
f = 1 MHz
o
25°C
Full range
25°C
70
68
82
80
89
70
68
82
80
89
Common-mode
rejection ratio
V
IC
V
O
= V min,
ICR
CMRR
= 0,
R = 50 Ω
S
99
99
Supply-voltage rejection
V
V
=
= 0,
5 V to 15 V,
= 50 Ω
CC
k
SVR
ratio (∆V
/∆V )
IO
R
S
CC
O
Full range
†
Full range is −40°C to 125°C.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2071-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted) (continued)
=
5 V (unless
TLE2071-Q1
TLE2071A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
mA
T
A
MIN
1.35
TYP
MAX
2.2
MIN
1.35
TYP
MAX
25°C
1.6
1.6
2.2
2.2
I
I
Supply current
V
V
= 0,
= 0
No load
CC
O
Full range
2.2
V
V
= 1 V
−35
45
−35
45
ID
Short-circuit output
current
25°C
mA
OS
O
= −1 V
ID
†
Full range is −40°C to 125°C.
TLE2071-Q1 operating characteristics at specified free-air temperature, VCC = 5 V
TLE2071-Q1
TLE2071A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
25°C
35
35
SR+
SR−
Positive slew rate
V/µs
Full
range
20
20
20
V
A
= 2.3 V,
= −1,
O(PP)
R = 2 kΩ,
VD
L
25°C
38
38
C = 100 pF,
See Figure 1
L
Negative slew rate
Settling time
V/µs
Full
range
20
A
= −1,
VD
To 10 mV
To 1 mV
0.25
0.4
0.25
0.4
2-V step,
R = 1 kΩ,
C = 100 pF
t
s
25°C
25°C
µs
L
L
f = 10 Hz
28
55
17
28
55
17
Equivalent input noise
voltage
V
n
nV/√Hz
f = 10 kHz
11.6
11.6
R
= 20 Ω,
f = 10 Hz to
10 kHz
S
6
6
See Figure 3
Peak-to-peak equivalent
input noise voltage
V
N(PP)
25°C
µV
f = 0.1 Hz to
10 Hz
0.6
2.8
0.6
2.8
Equivalent input noise
current
I
n
V
V
= 0,
f = 10 kHz
25°C
25°C
fA/√Hz
IC
= 5 V,
A
VD
= 10,
O(PP)
Total harmonic distortion
plus noise
f = 1 kHz,
= 25 Ω
R = 2 kΩ,
L
THD + N
0.013%
0.013%
R
S
V = 10 mV,
C = 25 pF,
L
R = 2 kΩ,
See Figure 2
I
L
9.4
2.8
56
9.4
2.8
56
B
Unity-gain bandwidth
25°C
25°C
25°C
MHz
MHz
1
Maximum output-swing
bandwidth
V
O(PP)
= 4 V,
A
VD
= −1,
B
OM
R = 2 kΩ ,
L
C = 25 pF
L
Phase margin at unity
gain
V = 10 mV,
R = 2 kΩ,
I
L
φ
m
C = 25 pF,
L
See Figure 2
†
Full range is −40°C to 125°C.
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2071-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted)
=
15 V (unless
TLE2071-Q1
TLE2071A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
25°C
0.49
4
9
0.47
2
7
V
Input offset voltage
mV
IO
Full range
V
= 0,
V
= 0,
= 0,
IC
O
O
R = 50 Ω
S
Temperature coefficient
of input offset voltage
20
α
VIO
Full range
3.2
6
3.2
6
µV/°C
25°C
Full range
25°C
100
20
100
20
pA
nA
pA
nA
I
IO
Input offset current
Input bias current
V
IC
= 0,
V
See Figure 4
20
175
60
20
175
60
I
IB
Full range
15
to
15
to
15
to
15
to
25°C
−11 −11.9
−11 −11.9
Common-mode input
voltage range
V
R
I
= 50 Ω
S
V
V
ICR
15
to
−10.9
15
to
−10.9
Full range
25°C
Full range
25°C
13.8
14.1
13.9
12.3
13.8
14.1
13.9
12.3
= −200 µA
= −2 mA
= −20 mA
= 200 µA
= 2 mA
O
13.6
13.5
13.3
11.5
11.4
13.6
13.5
13.3
11.5
11.4
Maximum positive peak
output voltage swing
V
OM+
I
O
I
O
I
O
I
O
I
O
Full range
25°C
Full range
25°C
−13.8 −14.2
−13.8 −14.2
−13.6
Full range −13.6
25°C −13.5
Full range −13.3
25°C −11.5 −12.4
Full range −11.4
−14
−13.5
−13.3
−14
Maximum negative peak
output voltage swing
V
A
V
OM−
−11.5 −12.4
−11.4
= 20 mA
25°C
Full range
25°C
80
78
90
88
95
93
96
80
78
90
88
95
93
96
R = 600 Ω
L
109
109
Large-signal differential
voltage amplification
V
O
=
10 V R = 2 kΩ
dB
VD
L
Full range
25°C
118
118
R = 10 kΩ
L
Full range
25°C
12
12
Ω
r
Input resistance
V
V
= 0
10
10
i
IC
Common
mode
25°C
25°C
25°C
7.5
2.5
80
7.5
2.5
80
= 0,
IC
c
z
Input capacitance
pF
i
See Figure 5
Differential
Open-loop output
impedance
Ω
dB
dB
f = 1 MHz
o
25°C
Full range
25°C
80
78
82
80
98
80
78
82
80
98
Common-mode
rejection ratio
V
IC
V
O
= V min,
ICR
CMRR
= 0,
R = 50 Ω
S
99
99
Supply-voltage rejection
V
V
=
= 0,
5 V to 15 V,
= 50 Ω
CC
k
SVR
ratio (∆V
/∆V )
IO
R
S
CC
O
Full range
†
Full range is −40°C to 125°C.
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2071-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted) (continued)
=
15 V (unless
TLE2071-Q1
TLE2071A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
mA
T
A
MIN
TYP
MAX
2.2
MIN
TYP
MAX
25°C
1.35
1.7
1.35
1.7
2.2
2.2
I
I
Supply current
V
V
= 0,
= 0
No load
CC
O
Full range
2.2
V
V
= 1 V
−30
30
−45
48
−30
30
−45
48
ID
Short-circuit output current
25°C
mA
OS
O
= −1 V
ID
†
Full range is −40°C to 125°C.
TLE2071-Q1 operating characteristics at specified free-air temperature, VCC = 15 V
TLE2071-Q1
TLE2071A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
25°C
30
22
30
22
40
30
40
SR+
SR−
Positive slew rate
V/µs
Full
range
22
30
22
V
= 10 V,
A
= −1,
O(PP)
VD
R = 2 kΩ,
See Figure 1
C = 100 pF,
L
L
25°C
45
45
Negative slew rate
Settling time
V/µs
Full
range
A
= −1,
VD
To 10 mV
To 1 mV
0.4
1.5
0.4
1.5
10-V step,
R = 1kΩ,
C = 100 pF
t
s
25°C
25°C
µs
L
L
f = 10 Hz
28
55
17
28
55
17
Equivalent input noise
voltage
nV/√Hz
V
n
f = 10 kHz
11.6
11.6
R
= 20 Ω,
f = 10 Hz to
10 kHz
S
6
6
See Figure 3
Peak-to-peak equivalent
input noise voltage
V
N(PP)
25°C
µV
f = 0.1 Hz to
10 Hz
0.6
2.8
0.6
2.8
Equivalent input noise
current
I
n
V
V
= 0,
f = 10 kHz
25°C
25°C
fA/√Hz
IC
= 20 V,
A
VD
= 10,
O(PP)
Total harmonic distortion
plus noise
f = 1 kHz,
= 25 Ω
R = 2 kΩ,
L
THD + N
0.008%
0.008%
R
S
V = 10 mV,
C = 25 pF,
L
R = 2 kΩ,
See Figure 2
I
L
8
8
B
Unity-gain bandwidth
25°C
25°C
25°C
10
637
57
10
637
57
MHz
kHz
1
Maximum output-swing
bandwidth
V
O(PP)
= 20 V,
A
VD
= −1,
478
478
B
OM
R = 2 kΩ,
L
C = 25 pF
L
Phase margin at unity
gain
V = 10 mV,
R = 2 kΩ,
I
L
φ
m
C = 25 pF,
L
See Figure 2
†
Full range is −40°C to 125°C.
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2072-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted)
=
5 V (unless
TLE2072-Q1
TLE2072A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
6
MIN
TYP
MAX
25°C
0.9
0.65
3.5
8
V
IO
Input offset voltage
mV
Full range
10
V
= 0,
R = 50 Ω,
V
= 0,
= 0,
IC
O
O
S
Temperature coefficient
of input offset voltage
α
VIO
Full range
2.3
5
2.3
5
20 µV/°C
25°C
Full range
25°C
100
20
100
pA
nA
pA
nA
I
IO
Input offset current
Input bias current
20
175
60
V
IC
= 0,
V
See Figure 4
15
175
60
15
I
IB
Full range
5
to
−1
5
to
−1.9
5
to
−1
5
to
−1.9
25°C
Common-mode input
voltage range
V
R
I
= 50 Ω
S
V
V
ICR
5
to
−0.8
5
to
−0.8
Full range
25°C
Full range
25°C
3.8
3.6
3.5
3.3
1.5
1.4
−3.8
−3.6
−3.5
−3.3
−1.5
−1.4
80
4.1
3.9
3.8
3.6
3.5
3.3
1.5
1.4
−3.8
−3.6
−3.5
−3.3
−1.5
−1.4
80
4.1
3.9
= −200 µA
= −2 mA
= −20 mA
= 200 µA
= 2 mA
O
Maximum positive peak
output voltage swing
V
OM+
I
O
I
O
I
O
I
O
I
O
Full range
25°C
2.3
2.3
Full range
25°C
−4.2
−4.1
−2.4
91
−4.2
−4.1
−2.4
91
Full range
25°C
Maximum negative peak
output voltage swing
V
A
V
OM−
Full range
25°C
= 20 mA
Full range
25°C
R = 600 Ω
L
Full range
25°C
78
78
90
100
106
90
100
106
Large-signal differential
voltage amplification
V
O
=
2.3 V R = 2 kΩ
dB
VD
L
Full range
25°C
88
88
95
95
R = 10 kΩ
L
Full range
25°C
93
93
12
12
r
Input resistance
V
V
= 0
Ω
10
10
i
IC
Common
mode
25°C
25°C
25°C
11
2.5
80
11
2.5
80
= 0,
IC
c
z
Input capacitance
pF
i
See Figure 5
Differential
Open-loop output
impedance
f = 1 MHz
Ω
o
25°C
70
68
89
70
68
89
Common-mode
rejection ratio
V
IC
V
O
= V min,
= 0,
ICR
CMRR
dB
R = 50 Ω
S
Full range
†
Full range is −40°C to 125°C.
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2072-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted) (continued)
=
5 V (unless
TLE2072-Q1
TLE2072A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
Supply-voltage rejection
V
V
=
= 0,
5 V to 15 V,
= 50 Ω
CC
k
Full range
80
80
dB
SVR
ratio (∆V
/∆V )
IO
R
S
CC
O
25°C
Full range
25°C
2.7
2.9
3.6
3.6
2.7
2.9
3.6
3.6
Supply current
(both channels)
I
V
V
= 0,
= 0,
No load
mA
dB
CC
O
a
I
Crosstalk attenuation
R = 2 kΩ
L
120
−35
45
120
−35
45
x
IC
V
= 1 V
ID
ID
Short-circuit output
current
V
O
= 0
25°C
mA
OS
V
= −1 V
†
Full range is −40°C to 125°C.
TLE2072-Q1 operating characteristics at specified free-air temperature, VCC = 5 V
TLE2072-Q1
TLE2072A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
25°C
35
35
SR+
SR−
Positive slew rate
V/µs
Full
range
18
18
18
18
V
A
= 2.3 V,
= −1,
O(PP)
R = 2 kΩ,
See Figure 1
VD
L
25°C
38
38
C = 100 pF,
L
Negative slew rate
Settling time
V/µs
Full
range
A
= −1,
VD
To 10 mV
To 1 mV
0.25
0.4
0.25
0.4
2-V step,
R = 1 kΩ,
C = 100 pF
t
s
25°C
25°C
µs
L
L
f = 10 Hz
28
55
17
28
55
17
Equivalent input noise
voltage
nV/√Hz
V
n
f = 10 kHz
11.6
11.6
R
= 20 Ω,
f = 10 Hz to
10 kHz
S
6
6
Peak-to-peak
equivalent input
noise voltage
See Figure 3
V
N(PP)
25°C
µV
f = 0.1 Hz to
10 Hz
0.6
2.8
0.6
2.8
Equivalent input noise
current
I
n
V
V
= 0,
f = 10 kHz
25°C
25°C
fA/√Hz
IC
= 5 V,
A
VD
= 10,
O(PP)
Total harmonic
distortion plus noise
f = 1 kHz,
= 25 Ω
R = 2 kΩ,
L
THD + N
0.013%
0.013%
R
S
V = 10 mV,
C = 25 pF,
L
R = 2 kΩ,
See Figure 2
I
L
B
Unity-gain bandwidth
25°C
25°C
25°C
9.4
2.8
56
9.4
2.8
56
MHz
MHz
1
Maximum output-swing
bandwidth
V
O(PP)
= 4 V,
A
VD
= −1,
B
OM
R = 2 kΩ ,
L
C = 25 pF
L
Phase margin at unity
gain
V = 10 mV,
R = 2 kΩ,
I
L
φ
m
C = 25 pF,
L
See Figure 2
†
Full range is −40°C to 125°C.
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2072-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted)
=
15 V (unless
TLE2072-Q1
TLE2072A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
6
MIN
TYP
MAX
25°C
1.1
0.7
3.5
8
V
IO
Input offset voltage
mV
Full range
10
V
= 0,
R = 50 Ω
V
= 0,
= 0,
IC
O
O
S
Temperature coefficient
of input offset voltage
α
VIO
Full range
2.4
6
2.4
6
20 µV/°C
25°C
Full range
25°C
100
20
100
pA
nA
pA
nA
I
IO
Input offset current
Input bias current
20
175
60
V
IC
= 0,
V
See Figure 4
20
175
60
20
I
IB
Full range
15
to
15
to
15
to
15
to
25°C
−11 −11.9
−11 −11.9
Common-mode input
voltage range
V
R
I
= 50 Ω
S
V
V
ICR
15
to
−10.8
15
to
−10.8
Full range
25°C
Full range
25°C
13.8
14.1
13.9
12.3
13.8
14.1
13.9
12.3
= −200 µA
= −2 mA
= −20 mA
= 200 µA
= 2 mA
O
13.6
13.5
13.3
11.5
11.4
13.6
13.5
13.3
11.5
11.4
Maximum positive peak
output voltage swing
V
OM+
I
O
I
O
I
O
I
O
I
O
Full range
25°C
Full range
25°C
−13.8 −14.2
−13.8 −14.2
−13.6
Full range −13.6
25°C −13.5
Full range −13.3
25°C −11.5 −12.4
Full range −11.4
−14
−13.5
−13.3
−14
Maximum negative peak
output voltage swing
V
A
V
OM−
−11.5 −12.4
−11.4
= 20 mA
25°C
Full range
25°C
80
78
90
89
95
93
96
80
78
90
89
95
93
96
R = 600 Ω
L
109
109
Large-signal differential
voltage amplification
V
O
=
10 V R = 2 kΩ
dB
VD
L
Full range
25°C
118
118
R = 10 kΩ
L
Full range
25°C
12
12
r
Input resistance
V
V
= 0
Ω
10
10
i
IC
Common
mode
25°C
25°C
25°C
7.5
2.5
80
7.5
2.5
80
= 0,
IC
c
z
Input capacitance
pF
i
See Figure 5
Differential
Open-loop output
impedance
f = 1 MHz
Ω
dB
dB
o
25°C
Full range
25°C
80
78
82
80
98
80
78
82
80
98
Common-mode
rejection ratio
V
IC
V
O
= V min,
ICR
CMRR
= 0,
R = 50 Ω
S
99
99
Supply-voltage rejection
V
V
=
= 0,
5 V to 15 V,
= 50 Ω
CC
k
SVR
ratio (∆V
/∆V )
IO
R
S
CC
O
Full range
†
Full range is −40°C to 125°C.
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2072-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted) (continued)
=
15 V (unless
TLE2072-Q1
TLE2072A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
3.6
MIN
TYP
MAX
25°C
Full range
25°C
2.7
3.1
2.7
3.1
3.6
3.6
Supply current
(both channels)
I
V
V
= 0,
= 0,
No load
mA
dB
CC
O
3.6
a
I
Crosstalk attenuation
R = 2 kΩ
L
120
−45
48
120
−45
48
x
IC
V
= 1 V
−30
30
−30
30
ID
ID
Short-circuit output
current
V
O
= 0
25°C
mA
OS
V
= −1 V
†
Full range is −40°C to 125°C.
TLE2072-Q1 operating characteristics at specified free-air temperature, VCC = 15 V
TLE2072-Q1
TLE2072A-Q1
†
PARAMETER
TEST CONDITIONS
UNIT
T
A
MIN
TYP
MAX
MIN
TYP
MAX
25°C
28
20
30
20
40
28
20
30
20
40
SR+
SR−
Positive slew rate
V/µs
Full
range
V
= 10 V,
A
= −1,
O(PP)
VD
R = 2 kΩ,
See Figure 1
C = 100 pF,
L
L
25°C
45
45
Negative slew rate
Settling time
V/µs
Full
range
A
= −1,
VD
To 10 mV
To 1 mV
0.4
1.5
0.4
1.5
10-V step,
R = 1kΩ,
C = 100 pF
t
s
25°C
25°C
µs
L
L
f = 10 Hz
28
55
17
28
55
17
Equivalent input noise
voltage
nV/√Hz
V
n
f = 10 kHz
11.6
11.6
R
= 20 Ω,
f = 10 Hz to
10 kHz
S
6
6
Peak-to-peak
equivalent input
noise voltage
See Figure 3
V
N(PP)
25°C
25°C
µV
f = 0.1 Hz to
10 Hz
0.6
2.8
0.6
2.8
Equivalent input noise
current
I
n
V
V
= 0,
f = 10 kHz
fA/√Hz
IC
= 20 V,
A
VD
= 10,
O(PP)
Total harmonic
distortion plus noise
THD + N
25°C
25°C
25°C
25°C
0.008%
10
0.008%
10
f = 1 kHz,
= 25 Ω
R = 2 kΩ,
L
R
S
V = 10 mV,
R = 2 kΩ,
I
L
8
8
B
Unity-gain bandwidth
MHz
kHz
1
C = 25 pF,
See Figure 2
L
Maximum
output-swing
bandwidth
V
O(PP)
= 20 V,
A
VD
= −1,
478
478
B
OM
637
57
637
57
R = 2 kΩ,
C = 25 pF
L
L
Phase margin at unity V = 10 mV,
R = 2 kΩ,
I
L
φ
m
gain
C = 25 pF,
See Figure 2
L
†
Full range is −40°C to 125°C.
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2074-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted)
=
5 V (unless
TLE2074-Q1
MIN TYP MAX
TLE2074A-Q1
MIN TYP MAX
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
25°C
−1.6
7
−0.5
4
9
V
Input offset voltage
mV
IO
Full range
11
V
= 0,
V
= 0,
= 0,
IC
O
O
R = 50Ω
S
Temperature coefficient
of input offset voltage
α
VIO
Full range
10.1
15
10.1
15
30 µV/°C
25°C
Full range
25°C
100
20
100
pA
nA
pA
nA
I
IO
Input offset current
Input bias current
20
175
60
V
IC
= 0,
V
See Figure 4
20
175
60
20
I
IB
Full range
5
to
5
to
5
to
5
to
25°C
−1.9
−1
−1.9
−1
Common-mode input
voltage range
V
R
I
= 50 Ω
S
V
V
ICR
5
to
−0.8
5
to
−0.8
Full range
25°C
Full range
25°C
3.8
3.6
3.5
3.3
1.5
1.4
−3.8
−3.6
−3.5
−3.3
−1.5
−1.4
80
4.1
3.9
3.8
3.6
3.5
3.3
1.5
1.4
−3.8
−3.6
−3.5
−3.3
−1.5
−1.4
80
4.1
3.9
= −200 µA
= −2 mA
= −20 mA
= 200 µA
= 2 mA
O
Maximum positive peak
output voltage swing
V
OM+
I
O
I
O
I
O
I
O
I
O
Full range
25°C
2.3
2.3
Full range
25°C
−4.2
−4.1
−2.4
91
−4.2
−4.1
−2.4
91
Full range
25°C
Maximum negative peak
output voltage swing
V
A
V
OM−
Full range
25°C
= 20 mA
Full range
25°C
R = 600 Ω
L
Full range
25°C
78
78
90
100
106
90
100
106
Large-signal differential
voltage amplification
V
O
=
2.3 V R = 2 kΩ
dB
VD
L
Full range
25°C
88
88
95
95
R = 10 kΩ
L
Full range
25°C
93
93
12
12
r
Input resistance
V
V
= 0
Ω
10
10
i
IC
Common mode
Differential
25°C
11
2.5
80
11
2.5
80
Input
capacitance
c
z
= 0,
See Figure 5
pF
i
IC
25°C
Open-loop output impedance
f = 1 MHz
25°C
Ω
o
25°C
70
68
82
80
89
70
68
82
80
89
V
V
= V min,
= 0,
IC
O
ICR
CMRR Common-mode rejection ratio
Supply-voltage rejection ratio
dB
dB
R = 50 Ω
S
Full range
25°C
99
99
V
V
=
= 0,
5 V to 15 V,
= 50 Ω
CC
k
SVR
(∆V
/∆V )
IO
R
S
Full range
CC
O
†
Full range is −40°C to 125°C.
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2074-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted) (continued)
=
5 V (unless
TLE2074-Q1
MIN TYP MAX
5.2
TLE2074A-Q1
MIN TYP MAX
5.2
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
25°C
Full range
25°C
6.3
7.5
7.5
6.3
7.5
7.5
Supply current
(four amplifiers)
I
I
V
V
= 0,
= 0,
No load
mA
dB
CC
O
Crosstalk attenuation
R = 2 kΩ
L
120
−35
45
120
−35
45
IC
V
= 1 V
ID
ID
Short-circuit output current
V
O
= 0
25°C
mA
OS
V
= −1 V
†
Full range is −40°C to 125°C.
TLE2074-Q1 operating characteristics at specified free-air temperature, VCC = 5 V
TLE2074-Q1
TLE2074A-Q1
†
T
PARAMETER
TEST CONDITIONS
UNIT
A
MIN
TYP
35
MAX
MIN
TYP
35
MAX
25°C
SR+
SR−
Positive slew rate
V/µs
Full
range
18
18
18
18
V
A
= 2.3 V,
= −1,
O(PP)
R = 2 kΩ,
VD
L
25°C
38
38
C = 100 pF,
See Figure 1
L
Negative slew rate
Settling time
V/µs
Full
range
A
= −1,
VD
To 10 mV
To 1 mV
0.25
0.4
0.25
0.4
2-V step,
R = 1 kΩ,
C = 100 pF
t
s
25°C
25°C
µs
L
L
f = 10 Hz
28
55
17
28
55
17
Equivalent input noise
voltage
nV/√Hz
V
n
f = 10 kHz
11.6
11.6
R
= 20 Ω,
f = 10 Hz to
10 kHz
S
6
6
See Figure 3
Peak-to-peak equivalent
input noise voltage
V
N(PP)
25°C
µV
f = 0.1 Hz to
10 Hz
0.6
2.8
0.6
2.8
Equivalent input noise
current
I
n
V
V
= 0,
f = 10 kHz
25°C
25°C
fA/√Hz
IC
= 5 V,
A
VD
= 10,
O(PP)
Total harmonic distortion
plus noise
f = 1 kHz,
= 25 Ω
R = 2 kΩ,
L
THD + N
0.013%
0.013%
R
S
V = 10 mV,
C = 25 pF,
L
R = 2 kΩ,
See Figure 2
I
L
B
Unity-gain bandwidth
25°C
25°C
25°C
9.4
2.8
56
9.4
2.8
56
MHz
MHz
1
Maximum output-swing
bandwidth
V
O(PP)
= 4 V,
A
VD
= −1,
B
OM
R = 2 kΩ,
L
C = 25 pF
L
Phase margin at unity
gain
V = 10 mV,
R = 2 kΩ,
I
L
f
m
C = 25 pF,
L
See Figure 2
†
Full range is −40°C to 125°C.
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2074-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted)
=
15 V (unless
TLE2074-Q1
MIN TYP MAX
TLE2074A-Q1
MIN TYP MAX
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
25°C
−1.6
7
−0.5
4
9
V
Input offset voltage
mV
IO
Full range
11
V
= 0,
V
= 0,
= 0,
IC
O
O
R = 50 Ω
S
Temperature coefficient
of input offset voltage
α
VIO
Full range
10.1
15
10.1
15
30 µV/°C
25°C
Full range
25°C
100
20
100
pA
nA
pA
nA
I
IO
Input offset current
Input bias current
20
175
60
V
IC
= 0,
V
See Figure 4
25
175
60
25
I
IB
Full range
15
to
15
to
−11.9
15
to
15
to
25°C
−11 −11.9
−11
Common-mode input
voltage range
V
R
I
= 50 Ω
S
V
V
ICR
15
to
−10.8
15
to
−10.8
Full range
25°C
Full range
25°C
13.8
13.6
13.5
13.3
11.5
11.4
14.1
13.9
12.3
13.8
14.1
13.9
12.3
= −200 µA
= −2 mA
= −20 mA
= 200 µA
= 2 mA
O
13.6
13.5
13.3
11.5
11.4
Maximum positive peak
output voltage swing
V
OM+
I
O
I
O
I
O
I
O
I
O
Full range
25°C
Full range
25°C
−13.8 −14.2
−13.8 −14.2
−13.6
Full range −13.6
25°C −13.5
Full range −13.3
25°C −11.5 −12.4
Full range −11.4
−14
−13.5
−13.3
−14
Maximum negative peak
output voltage swing
V
A
V
OM−
−11.5 −12.4
−11.4
= 20 mA
25°C
Full range
25°C
80
78
90
88
95
93
96
80
78
90
88
95
93
96
R = 600 Ω
L
109
109
Large-signal differential
voltage amplification
V
O
=
10 V
R = 2 kΩ
L
dB
VD
Full range
25°C
118
118
R = 10 kΩ
L
Full range
25°C
12
12
r
Input resistance
V
V
= 0
Ω
10
10
i
IC
Common mode
Differential
25°C
7.5
2.5
80
7.5
2.5
80
Input
capacitance
c
z
= 0,
See Figure 5
pF
i
IC
25°C
Open-loop output impedance f = 1 MHz
25°C
Ω
o
25°C
80
78
82
80
98
80
78
82
80
98
V
V
= V min,
= 0,
IC
O
ICR
CMRR Common-mode rejection ratio
Supply-voltage rejection
dB
dB
R = 50 Ω
S
Full range
25°C
99
99
V
V
=
= 0,
5 V to 15 V,
= 50 Ω
CC
k
SVR
ratio (∆V
/∆V )
IO
R
S
CC
O
Full range
†
Full range is −40°C to 125°C.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TLE2074-Q1 electrical characteristics at specified free-air temperature, VCC
otherwise noted) (continued)
=
15 V (unless
TLE2074-Q1
MIN TYP MAX
TLE2074A-Q1
MIN TYP MAX
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
25°C
Full range
25°C
5.2
6.5
7.5
7.5
5.2
6.5
7.5
7.5
Supply current
(four amplifiers)
I
I
V
V
= 0,
= 0,
No load
mA
dB
CC
O
Crosstalk attenuation
R = 2 kΩ
L
120
−45
48
120
−45
48
IC
V
= 1 V
−30
30
−30
30
ID
ID
Short-circuit output current
V
O
= 0
25°C
mA
OS
V
= −1 V
†
Full range is −40°C to 125°C.
TLE2074-Q1 operating characteristics at specified free-air temperature, VCC = 15 V
TLE2074-Q1
TLE2074A-Q1
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
MAX
MIN
TYP
MAX
25°C
25
17
30
20
40
25
17
30
20
40
SR+
SR−
Positive slew rate
V/µs
Full
range
V
= 10 V,
A
= −1,
O(PP)
VD
R = 2 kΩ,
See Figure 1
C = 100 pF,
L
L
25°C
45
45
Negative slew rate
Settling time
V/µs
Full
range
A
= −1,
VD
To 10 mV
To 1 mV
0.4
1.5
0.4
1.5
10-V step,
R = 1kΩ,
C = 100 pF
t
s
25°C
25°C
µs
L
L
f = 10 Hz
28
55
17
28
55
17
Equivalent input noise
voltage
nV/√Hz
V
n
f = 10 kHz
11.6
11.6
R
= 20 Ω,
f = 10 Hz to
10 kHz
S
6
0.6
2.8
6
0.6
2.8
See Figure 3
Peak-to-peak equivalent
input noise voltage
V
N(PP)
25°C
µV
f = 0.1 Hz to
10 Hz
Equivalent input noise
current
fA/√Hz
I
n
V
V
= 0,
f = 10 kHz
25°C
25°C
IC
= 20 V,
A
VD
= 10,
O(PP)
Total harmonic distortion
plus noise
THD + N
0.008%
0.008%
f = 1 kHz,
= 25 Ω
R = 2 kΩ,
L
R
S
V = 10 mV,
C = 25 pF,
L
R = 2 kΩ,
See Figure 2
I
L
8
8
B
Unity-gain bandwidth
25°C
25°C
25°C
10
637
57
10
637
57
MHz
kHz
1
Maximum output-swing
bandwidth
V
O(PP)
= 20 V,
A
VD
= −1,
478
478
B
OM
R = 2 kΩ,
L
C = 25 pF
L
Phase margin at unity
gain
V = 10 mV,
R = 2 kΩ,
I
L
φ
m
C = 25 pF,
L
See Figure 2
†
Full range is −40°C to 125°C.
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
PARAMETER MEASUREMENT INFORMATION
2 kΩ
10 kΩ
V
CC+
V
CC+
2 kΩ
100Ω
V
I
V
I
−
+
−
+
V
O
V
O
V
CC+
V
CC+
†
R
†
R
L
C
L
L
C
L
†
†
Includes fixture capacitance
Includes fixture capacitance
Figure 1. Slew-Rate Test Circuit
Figure 2. Unity-Gain Bandwidth
and Phase-Margin Test Circuit
2 kΩ
V
CC+
V
CC+
Ground Shield
−
+
−
+
V
O
V
O
R
R
S
V
CC−
Picoammeters
S
V
CC−
Figure 3. Noise-Voltage Test Circuit
Figure 4. Input-Bias and Offset-
Current Test Circuit
V
CC+
IN−
IN+
−
+
C
V
O
id
C
C
V
CC−
ic
ic
Figure 5. Internal Input Capacitance
typical values
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
input bias and offset current
At the picoampere bias current level typical of the TLE207x and TLE207xA, accurate measurement of the bias
current becomes difficult. Not only does this measurement require a picoammeter but test socket leakages can
easily exceed the actual device bias currents. To accurately measure these small currents, Texas Instruments
uses a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but
with no device in the socket. The device is then inserted in the socket and a second test is performed that
measures both the socket leakage and the device input bias current. The two measurements are then
subtracted algebraically to determine the bias current of the device.
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
6, 7, 8
V
IO
Input offset voltage
Distribution
α
Temperature coefficient of input offset voltage
Input offset current
Distribution
9, 10, 11
12, 13
VIO
I
IO
vs Free-air temperature
vs Free-air temperature
vs Total supply voltage
12, 13
14
I
IB
Input bias current
V
V
V
V
Common-mode input voltage range
Output voltage
vs Free-air temperature
vs Differential input voltage
vs Output current
15
16, 17
18
ICR
O
Maximum positive peak output voltage
Maximum negative peak output voltage
OM+
OM−
vs Output current
19
vs Free-air temperature
vs Supply voltage
20, 21
22
V
OM
Maximum peak output voltage
V
V
Maximum peak-to-peak output voltage
Output voltage
vs Frequency
23
24
O(PP)
vs Settling time
O
vs Load resistance
vs Free-air temperature
25
26, 27
A
Large-signal differential voltage amplification
Small-signal differential voltage amplification
Common-mode rejection ratio
VD
A
VD
vs Frequency
28, 29
vs Frequency
vs Free-air temperature
30
31
CMRR
vs Frequency
vs Free-air temperature
32
33
k
Supply-voltage rejection ratio
Supply current
SVR
vs Supply voltage
vs Free-air temperature
vs Differential input voltage
34, 35, 36
37, 38, 39
40 − 45
I
CC
vs Supply voltage
vs Elapsed time
vs Free-air temperature
46
47
48
I
Short-circuit output current
Slew rate
OS
vs Free-air temperature
vs Load resistance
49, 50
51
SR
vs Differential input voltage
52
V
V
Equivalent Input noise voltage (spectral density) vs Frequency
53
n
vs Noise bandwidth
54
55
Input referred noise voltage
n
Over a 10-second time interval
vs Frequency bands
vs Frequency
Third-octave spectral noise density
Total harmonic distortion plus noise
Unity-gain bandwidth
56
57, 58
59
THD +N
B
1
vs Load capacitance
vs Free-air temperature
vs Supply voltage
60
61
Gain-bandwidth product
Gain margin
vs Load capacitance
62
vs Free-air temperature
vs Supply voltage
vs Load capacitance
63
64
65
φ
m
Phase margin
Phase shift
vs Frequency
vs Time
28, 29
66
Noninverting large-signal pulse response
Small-signal pulse response
Closed-loop output impedance
Crosstalk attenuation
vs Time
67
z
vs Frequency
vs Frequency
68
o
69
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLE2072
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLE2071
INPUT OFFSET VOLTAGE
20
18
16
14
12
10
8
30
27
24
21
18
15
12
9
600 Units Tested From One Wafer Lot
V
T
=
15 V
CC
V
CC
=
15 V
= 25°C
A
T
A
= 25°C
P Package
P Package
6
4
2
0
6
3
0
− 4
− 2.4
− 0.8
0.8
2.4
4
− 4
− 2.4
− 0.8
0.8
2.4
4
− Input Offset Voltage − mV
V
IO
V
IO
− Input Offset Voltage − mV
Figure 6
Figure 7
DISTRIBUTION OF TLE2074
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLE2071 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
50
45
40
35
30
25
20
15
30
27
24
21
18
15
12
9
V
T
=
15 V
CC
V
T
=
15 V
CC
= 25°C
A
= − 55°C to 125°C
A
N Package
P Package
10
5
6
3
0
0
− 8
− 4.8
− 1.6
1.6
4.8
8
− 40 − 32 − 24 −16 − 8
0
8
16 24 32 40
− Input Offset Voltage − mV
V
IO
α
VIO
− Temperature Coefficient − µV/°C
Figure 8
Figure 9
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLE2072 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
DISTRIBUTION OF TLE2074 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
30
27
24
21
18
15
12
9
30
27
24
21
18
15
12
9
310 Amplifiers
V
T
=
15 V
CC
V
T
=
15 V
= − 55°C to 125°C
CC
A
= − 55°C to 125°C
N Package
A
P Package
6
3
0
6
3
0
− 30 − 24 −18 −12 − 6
0
6
12 18 24 30
− 40 − 32 − 24 −16 − 8
0
8
16 24 32 40
α
VIO
− Temperature Coefficient − µV/°C
α
VIO
− Temperature Coefficient − µV/°C
Figure 10
Figure 11
INPUT BIAS CURRENT AND
INPUT OFFSET CURRENT†
vs
INPUT BIAS CURRENT AND
INPUT OFFSET CURRENT†
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
100
10
100
10
V
V
V
=
= 0
= 0
5 V
V
V
V
= 15 V
= 0
= 0
CC
CC
IC
O
IC
O
I
IB
1
1
I
IB
I
IO
0.1
0.1
I
IO
0.01
0.01
0.001
0.001
25 45 65 85 105 125
− Free-Air Temperature − °C
25 45 65 85 105 125
−75 −55 −35 −15 −5
−75 −55 −35 −15
5
T
A
T
A
− Free-Air Temperature − °C
Figure 12
Figure 13
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
COMMON-MODE INPUT VOLTAGE RANGE†
INPUT BIAS CURRENT
vs
vs
TOTAL SUPPLY VOLTAGE
FREE-AIR TEMPERATURE
6
10
V
CC+
+0.5
V
IC
max = V
CC+
R
= 50 Ω
S
T
A
= 125°C
5
4
V
CC+
10
10
V min
IC
V
IC
max
V
CC+
−0.5
3
2
1
10
10
10
V
+3.5
+3
CC−
V
min
IC
V
CC−
T
= 25°C
A
V
CC−
+2.5
+2
T
= −55°C
A
0
V
10
CC−
− 75 −55 −35 −15
5
25 45 65 85 105 12
0
5
10 15
20 25
30
35
40
45
V
CC
− Total Supply Voltage (referred to V
) − V
T
A
− Free-Air Temperature − °C
CC−
Figure 14
Figure 15
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
DIFFERENTIAL INPUT VOLTAGE
400
300
400
300
V
V
= 5 V
= 0
= 50 Ω
= 25°C
V
V
= 15 V
= 0
= 50 Ω
= 25°C
CC
CC
IC
IC
R
T
R
T
S
S
A
A
R = 600 Ω
L
R = 600 Ω
L
200
200
R = 2 kΩ
L
100
0
100
0
R = 2 kΩ
L
R = 10 kΩ
L
R = 10 kΩ
L
R = 10 kΩ
L
R = 10 kΩ
L
− 100
− 200
− 300
− 400
− 100
− 200
− 300
− 400
R = 2 kΩ
L
R = 2 kΩ
L
R = 600 Ω
L
R = 600 Ω
L
− 5 − 4 − 3 − 2 − 10
0
1
2
3
4
5
− 15
− 10
− 5
0
5
10
15
V
ID
− Differential Input Voltage − µV
V
ID
− Differential Input Voltage − µV
Figure 16
Figure 17
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE†
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE†
vs
vs
OUTPUT CURRENT
OUTPUT CURRENT
15
−15
13.5
12
−13.5
−12
T
A
= −55°C
T
A
= −55°C
10.5
9
−10.5
− 9
T
= 25°C
A
7.5
6
−7.5
− 6
T
= 25°C
= 85°C
A
T
A
= 125°C
4.5
T
A
T
A
= 85°C
− 4.5
T
= 125°C
A
3
1.5
0
− 3
−1.5
0
V
=
15 V
CC
V
=
15 V
CC
0
− 5 −10 −15 − 20 − 25 − 30 − 35 − 40 − 45 − 50
0
5
10 15 20 25 30 35 40 45 50
I
O
− Output Current − mA
I
O
− Output Current − mA
Figure 18
Figure 19
MAXIMUM PEAK OUTPUT VOLTAGE†
MAXIMUM PEAK OUTPUT VOLTAGE†
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
5
4
15
14.5
14
I
O
= 200 µA
I
= −200 µA
O
I
O
= −200 µA
I
O
= −2 mA
3
I
= 2 mA
O
2
13.5
13
I
O
= −20 mA
I
= −2 mA
O
1
I
O
= 20 mA
V
CC
= 5 V
0
12.5
12
I
O
= −20 mA
− 1
− 2
I
O
= 20 mA
11.5
− 3
− 4
− 5
11
10.5
10
I
= 2 mA
O
V
=
15 V
CC
I
= 200 µA
O
−75 −55 −35 −15
−75 −55 −35 −15
5
25 45 65 85 105 125
5
25 45 65 85 105 125
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 20
Figure 21
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE†
MAXIMUM PEAK OUTPUT VOLTAGE
vs
vs
FREQUENCY
SUPPLY VOLTAGE
30
25
20
15
10
5
V
CC
= 15 V
R = 2 kΩ
L
T
A
= 25°C
T
A
= 25°C,
125°C
I
= −200 µA
O
25
20
15
10
I
O
= −2 mA
I
O
= −20 mA
= 20 mA
T
A
= −55°C
0
T
A
= 25°C,
I
O
− 5
−10
125°C
= 5 V
V
CC
I
O
= 2 mA
−15
− 20
− 25
I
O
= 200 µA
5
0
T
A
= −55°C
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
100 k
1 M
10 M
f − Frequency − Hz
|V
CC
| − Supply Voltage − V
Figure 22
Figure 23
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
OUTPUT VOLTAGE
vs
SETTLING TIME
LOAD RESISTANCE
125
12.5
10
V
R
T
A
= 0
= 50 Ω
= 25°C
IC
S
10 mV
120
115
1mV
7.5
5
V
=
15 V
CC
V
CC
= 15 V
2.5
Rising
Falling
R = 1 kΩ
C = 100 pF
110
L
L
0
A = −1
V
105
100
T
A
= 25°C
− 2.5
V
CC
= 5 V
− 5
− 7.5
− 10
1mV
10 mV
95
90
− 12.5
0.1
1
10
100
0
0.5
1
1.5
2
t − Settling Time − µs
s
R − Load Resistance − kΩ
L
Figure 24
Figure 25
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
24
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION†
vs
FREE-AIR TEMPERATURE
110
107
104
101
98
R = 10 kΩ
L
R = 2 kΩ
L
95
92
R = 600 Ω
L
89
86
83
80
V
V
=
2.3 V
5 V
CC
=
O
−75 − 55 − 35 −15
5
25 45 65 85 105 125
T
A
− Free-Air Temperature − °C
Figure 26
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION†
vs
FREE-AIR TEMPERATURE
125
121
117
113
109
105
101
97
V
V
=
10 V
15 V
CC
R = 10 kΩ
L
=
O
R = 2 kΩ
L
R = 600 Ω
L
93
89
85
−75 − 55 − 35 −15
5
25 45 65 85 105 125
T
A
− Free-Air Temperature − °C
Figure 27
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
25
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
SMALL-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
140
120
0°
V
=
15 V
CC
20°
R = 2 kΩ
L
C = 100 pF
L
Gain
40°
60°
100
80
60
40
20
0
T
A
= 25°C
Phase Shift
80°
100°
120°
140°
− 20
− 40
160°
180°
1
10 100 1 k 10 k 100 k 1 M 10 M 100 M
f − Frequency − Hz
Figure 28
SMALL-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
30
20
80°
100°
120°
140°
C = 100 pF
L
Phase Shift
C = 25 pF
L
10
Gain
0
C = 100 pF
L
C = 25 pF
L
V
V
=
= 0
15 V
CC
− 10
− 20
160°
180°
IC
R = 2 kΩ
T
A
L
= 25°C
1
4
10
40
100
f − Frequency − MHz
Figure 29
26
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
COMMON-MODE REJECTION RATIO
COMMON-MODE REJECTION RATIO†
vs
vs
FREQUENCY
FREE-AIR TEMPERATURE
100
90
80
70
60
50
40
30
100
97
94
91
88
85
82
79
V
CC
= 15 V
V
=
15 V
5 V
CC
V
CC
= 5 V
V
=
CC
V
V
= 0
= 0
= 50 Ω
= 25°C
IC
20
10
0
76
73
70
V
V
R
= V min
= 0
= 50 Ω
IC
ICR
O
R
T
O
S
S
A
10
100
1 k
10 k
100 k
1 M
10 M
−75 − 55 − 35 −15
5
25 45 65 85 105 125
f − Frequency − Hz
T
A
− Free-Air Temperature − °C
Figure 30
Figure 31
SUPPLY-VOLTAGE REJECTION RATIO†
SUPPLY-VOLTAGE REJECTION RATIO
vs
vs
FREE-AIR TEMPERATURE
FREQUENCY
120
120
114
108
102
96
k
SVR+
100
80
k
SVR+
60
40
90
k
SVR−
k
SVR−
84
78
20
0
∆V
=
5 V to 15 V
CC
∆V
=
5 V to 15 V
V
IC
= 0
= 0
CC
72
66
60
V
O
V
= 0
= 0
IC
R
T
= 50 Ω
= 25°C
V
O
S
R
= 50 Ω
A
S
− 20
10
100
1 k
10 k
100 k
1 M
10 M
−75 − 55 − 35 −15
5
25 45 65 85 105 125
f − Frequency − Hz
T
A
− Free-Air Temperature − °C
Figure 32
Figure 33
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
27
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
TLE2072
SUPPLY CURRENT
vs
TLE2071
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
4
3.8
3.6
3.4
3.2
3
4
3.6
3.2
2.8
2.4
2
V
V
= 0
= 0
V
V
= 0
= 0
IC
IC
O
O
No Load
No Load
T
A
= 25°C
T
A
= 125°C
T
A
= 125°C
T
= 25°C
A
2.8
2.6
1.6
1.2
T
A
= −55°C
T
A
= −55°C
2.4
2.2
2
0.8
0.4
0
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
|V | − Supply Voltage − V
0
2
4
6
8
10 12 14 16 18 20
|V
| − Supply Voltage − V
CC
CC
Figure 34
Figure 35
TLE2071
TLE2074
SUPPLY CURRENT
vs
SUPPLY CURRENT†
vs
FREE-AIR TEMPERATURE
SUPPLY VOLTAGE
4
10
8
V
= 0
= 0
V
= 0
= 0
IC
IC
V
O
V
O
3.6
No Load
No Load
T
= 125°C
3.2
2.8
2.4
2
A
6
4
V
=
15 V
5 V
CC
T
A
= 25°C
T
= −55°C
A
1.6
1.2
V
=
CC
0.8
0.4
0
2
0
−75 − 55 − 35 −15
5
25 45 65 85 105 125
0
2
4
6
8
10 12 14 16 18 20
|V
CC
| − Supply Voltage − V
T
A
− Free-Air Temperature − °C
Figure 36
Figure 37
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
28
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
TLE2072
SUPPLY CURRENT†
vs
TLE2074
SUPPLY CURRENT†
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
3.5
3.4
3.3
3.2
3.1
3
10
9
V
V
= 0
= 0
V
V
= 0
= 0
IC
IC
O
O
No Load
No Load
V
=
15 V
5 V
CC
8
7
6
5
V
=
CC
2.9
2.8
V
=
15 V
5 V
CC
2.7
2.6
2.5
V
=
CC
−75 −55 −35 −15
5
25 45 65 85 105 125
− 75 − 55 − 35 − 15
5
25 45 65 85 105 125
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 38
Figure 39
TLE2071
SUPPLY CURRENT
vs
TLE2072
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
DIFFERENTIAL INPUT VOLTAGE
12
14
12
V
V
V
T
= 5 V
= 0
= 4.5 V
CC+
CC−
V
V
V
T
= 5 V
= 0
= 4.5 V
CC+
CC−
IC
10
8
IC
= 25°C
A
= 25°C
A
Open Loop
No Load
Open Loop
No Load
10
8
6
4
2
6
4
2
0
0
− 0.5
− 0.25
0
0.25
0.5
− 0.5
− 0.25
0
0.25
0.5
V
ID
− Differential Input Voltage − V
V
ID
− Differential Input Voltage − V
Figure 40
Figure 41
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
29
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
TLE2071
SUPPLY CURRENT
vs
TLE2074
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
DIFFERENTIAL INPUT VOLTAGE
25
23
20
18
15
13
10
8
20
18
16
14
12
10
8
V
V
T
=
= 0
= 25°C
15 V
CC
V
V
V
T
= 5 V
= 0
= 4.5 V
CC+
CC−
IC
A
IC
Open Loop
No Load
= 25°C
A
Open Loop
No Load
6
4
5
2
3
0
0
−1.5
− 0.9
− 0.3
0
0.3
0.9
1.5
− 0.5
− 0.25
0
0.25
0.5
V
ID
− Differential Input Voltage − V
V
ID
− Differential Input Voltage − V
Figure 42
Figure 43
TLE2074
SUPPLY CURRENT
vs
TLE2072
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
DIFFERENTIAL INPUT VOLTAGE
40
36
32
28
24
20
16
12
8
25
20
15
10
V
V
T
=
= 0
= 25°C
15 V
V
V
T
=
15 V
= 25°C
CC
CC
= 0
IC
IC
A
A
Open Loop
No Load
Open Loop
No Load
5
0
4
0
−1.5
−1
− 0.5
0
0.5
1
1.5
−1.5 −1.2 − 0.9 − 0.6 − 0.3
0
0.3 0.6 0.9 1.2 1.5
V
ID
− Differential Input Voltage − V
V
ID
− Differential Input Voltage − V
Figure 44
Figure 45
30
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
SHORT-CIRCUIT OUTPUT CURRENT
SHORT-CIRCUIT OUTPUT CURRENT
vs
vs
ELAPSED TIME
SUPPLY VOLTAGE
50
40
30
20
60
48
V
ID
= −1 V
V
ID
= −1 V
36
24
10
12
V
V
T
=
= 0
= 25°C
15 V
CC
V
T
= 0
= 25°C
O
0
0
O
A
A
−10
−12
− 24
− 20
− 30
V
ID
= 1 V
− 36
− 48
− 60
V
ID
= 1 V
− 40
− 50
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
0
60
120
180
t − Elapsed Time − s
|V
CC
| − Supply Voltage − V
Figure 46
Figure 47
SHORT-CIRCUIT OUTPUT CURRENT†
SLEW RATE†
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
80
64
45
43
41
39
37
35
33
31
V
= 15 V
CC
R = 2 kΩ
C = 100 pF
V
= −1 V
L
ID
V
= 15 V
CC
L
48
32
SR−
SR+
V
= 5 V
CC
16
0
− 16
− 32
V
=
5 V
=
CC
V
= 1 V
ID
V
15 V
− 48
− 64
− 80
29
27
25
CC
V
O
= 0
−75 − 55 − 35 −15
5
25 45 65 85 105 125
−75 − 55 − 35 −15
5
25 45 65 85 105 125
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 48
Figure 49
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
31
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
SLEW RATE†
vs
SLEW RATE
vs
LOAD RESISTANCE
FREE-AIR TEMPERATURE
50
40
70
66
62
Rising Edge
V
=
15 V
CC
R = 2 kΩ
C = 100 pF
L
L
30
20
10
0
58
54
50
46
42
38
34
30
V
CC
V
O
=
=
15 V
10 V
V
CC
=
=
5 V
2.5 V
V
O
SR−
SR+
−10
A
V
= −1
C = 100 pF
− 20
− 30
L
T
A
= 25°C
− 40
− 50
Falling Edge
100
1 k
10 k
100 k
−75 − 55 − 35 −15
5
25 45 65 85 105 125
T
A
− Free-Air Temperature − °C
R − Load Resistance − Ω
L
Figure 50
Figure 51
EQUIVALENT INPUT NOISE VOLTAGE
SLEW RATE
vs
DIFFERENTIAL INPUT VOLTAGE
(SPECTRAL DENSITY)
vs
FREQUENCY
50
40
50
45
40
35
30
25
A
= −1
V
V
V
= 15 V
= 0
= 20 Ω
= 25°C
CC
IC
R
T
S
30
A
= 1
V
Rising Edge
A
20
V
V
=
=
15 V
10 V (10% − 90%)
10
CC
O
0
C = 100 pF
L
T
A
= 25°C
−10
− 20
− 30
− 40
− 50
20
15
10
5
Falling Edge
A
= −1
V
A
= 1
V
0
10
0.1
0.4
1
4
10
100
1 k
10 k
f − Frequency − Hz
V
ID
− Differential Input Voltage − V
Figure 52
Figure 53
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
32
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
INPUT-REFERRED NOISE VOLTAGE
vs
INPUT-REFERRED NOISE VOLTAGE
OVER A 10-SECOND TIME INTERVAL
NOISE BANDWIDTH
100
10
1.2
V
V
= 15 V
= 0
= 20 Ω
= 25°C
CC
V
=
15 V
CC
IC
f = 0.1 to 10 Hz
T
A
R
T
S
0.9
0.6
= 25°C
A
Peak-to-Peak
0.3
1
0.1
RMS
0
− 0.3
− 0.6
0.01
100 k
1
10
100
1 k
10 k
0
1
2
3
4
5
6
7
8
9
10
Noise Bandwidth − Hz
t − Time − s
Figure 54
Figure 55
THIRD-OCTAVE SPECTRAL NOISE DENSITY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
vs
FREQUENCY BANDS
FREQUENCY
− 75
− 80
− 85
1
Start Frequency: 12.5 Hz
Stop Frequency: 20 kHz
V
V
T
= 15 V
= 0
= 25°C
CC
IC
A = 100, R = 600 Ω
A
V
L
0.1
0.01
− 90
− 95
A = 100, R = 2 kΩ
V
L
A = 10, R = 600 Ω
V
L
−100
−105
A = 10, R = 2 kΩ
V
L
V
V
T
=
5 V
CC
= 5 V
O(PP)
−110
−115
= 25°C
A
Filter: 10-Hz to 500-kHz Band Pass
0.001
10
15
20
25
30
35
40
45
10
100
1 k
10 k
100 k
Frequency Bands
f − Frequency − Hz
Figure 56
Figure 57
33
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
UNITY-GAIN BANDWIDTH
vs
vs
FREQUENCY
LOAD CAPACITANCE
1
13
Filter: 10-Hz to 500-kHz Band Pass
V
V
V
=
= 0
= 0
15 V
CC
V
V
T
=
15 V
CC
IC
= 20 V
O(PP)
O
12
11
10
9
= 25°C
R = 2 kΩ
T
A
A
L
= 25°C
0.1
A = 100, R = 600 Ω
V
L
A = 100, R = 2 kΩ
V
L
A = 10, R = 600 Ω
V
L
0.01
0.001
A = 10, R = 2 kΩ
V
L
8
7
10
100
1 k
10 k
100 k
0
20
40
60
80
100
f − Frequency − Hz
C − Load Capacitance − pF
L
Figure 58
Figure 59
GAIN-BANDWIDTH PRODUCT†
vs
GAIN-BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
SUPPLY VOLTAGE
13
12
11
10
9
13
f = 100 kHz
f = 100 kHz
V
V
= 0
= 0
IC
V
IC
= 0
O
12
11
10
9
V
O
= 0
R = 2 kΩ
L
R = 2 kΩ
L
C = 100 pF
L
C = 100 pF
L
T
A
= 25°C
V
CC
=
15 V
V
CC
= 5 V
8
8
7
7
−75 − 55 − 35 −15
5
25 45 65 85 105 125
0
5
10
15
20
25
|V| − Supply Voltage − V
CC
T
A
− Free-Air Temperature − °C
Figure 60
Figure 61
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
34
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
PHASE MARGIN†
vs
GAIN MARGIN
vs
FREE-AIR TEMPERATURE
LOAD CAPACITANCE
10
8
90°
80°
70°
60°
50°
V
V
V
= 15 V
= 0
= 0
V
V
= 0
= 0
CC
IC
O
IC
O
R = 2 kΩ
L
R = 2 kΩ
T
A
L
V
CC
= 15 V
= 25°C
C = 25 pF
L
6
V
CC
= 5 V
V
CC
= 15 V
40°
30°
4
2
0
C = 100 pF
L
V
CC
= 5 V
20°
10°
0°
0
20
40
60
80
100
−75 − 55 − 35 −15
5
25 45 65 85 105 125
C − Load Capacitance − pF
L
T
A
− Free-Air Temperature − °C
Figure 62
Figure 63
PHASE MARGIN
vs
PHASE MARGIN
vs
SUPPLY VOLTAGE
LOAD CAPACITANCE
90°
80°
70°
60°
50°
90°
80°
70°
60°
50°
C = 25 pF
L
V
CC
=
15 V
C = 100 pF
L
V
CC
= 5 V
40°
30°
20°
10°
0°
40°
30°
20°
10°
0°
V
V
= 0
= 0
V
V
= 0
= 0
IC
O
IC
O
R = 2 kΩ
T
A
R = 2 kΩ
T
A
L
L
= 25°C
= 25°C
0
4
8
12
16
20
0
20
40
60
80
100
|V
CC
| − Supply Voltage − V
C − Load Capacitance − pF
L
Figure 64
Figure 65
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
35
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
TYPICAL CHARACTERISTICS
NONINVERTING LARGE-SIGNAL
PULSE RESPONSE†
SMALL-SIGNAL PULSE RESPONSE
100
50
0
15
10
T
A
= 25°C,
125°C
T
= −55°C
A
5
T
A
= −55°C
0
T
A
= 25°C,
125°C
− 5
− 10
− 15
V
CC
V
= 15 V
V
=
15 V
− 50
CC
A = −1
A = 1
V
R = 2 kΩ
L
R = 2 kΩ
C = 100 pF
L
C = 100 pF
L
L
T
= 25°C
A
−100
0
1
2
3
4
5
0
0.4
0.8
1.2
1.6
t − Time − µs
t − Time − µs
Figure 66
Figure 67
TLE2072 AND TLE2074
CROSSTALK ATTENUATION
vs
CLOSED-LOOP OUTPUT IMPEDANCE
vs
FREQUENCY
FREQUENCY
100
140
V
T
=
15 V
CC
= 25°C
A
120
100
80
10
1
A = 100
V
0.1
A = 10
V
60
0.01
A = 1
V
V = 15 V
CC
V
= 0
IC
40
20
R = 2 kΩ
T
A
L
= 25°C
0.001
10 M
10
100
1 k
10 k
100 k
1 M
10
100
1 k
10 k
100 k
f − Frequency − Hz
f − Frequency − Hz
Figure 68
Figure 69
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
36
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
APPLICATION INFORMATION
input characteristics
The TLE207x, TLE207xA, and TLE207xB are specified with a minimum and a maximum input voltage that if
exceeded at either input could cause the device to malfunction. Because of the extremely high input impedance
and resulting low bias current requirements, the TLE207x, TLE207xA, and TLE207xB are well suited for
low-level signal processing; however, leakage currents on printed-circuit boards and sockets can easily exceed
bias current requirements and cause degradation in system performance. It is good practice to include guard
rings around inputs (see Figure 70). These guards should be driven from a low-impedance source at the same
voltage level as the common-mode input.
+
V
I
V
I
+
−
V
O
+
−
V
O
−
V
O
V
I
R2
R1
R3
R4
R3
R4
R2
R1
+
Where
Figure 70. Use of Guard Rings
TLE2071 input offset voltage nulling
The TLE2071 series offers external null pins that can be used to further reduce the input offset voltage. The
circuit of Figure 71 can be connected as shown if the feature is desired. When external nulling is not needed,
the null pins may be left unconnected.
−
+
IN−
IN+
OUT
N2
N1
100 kΩ
5 kΩ
V
CC−
Figure 71. Input Offset Voltage Nulling
37
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE207x-Q1, TLE207xA-Q1
EXCALIBUR LOW-NOISE HIGH-SPEED
JFET-INPUT OPERATIONAL AMPLIFIERS
ꢀ
SGLS226A − DECEMBER 2003 − REVISED AUGUST 2004
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using PSpice Parts model generation software. The Boyle
macromodel (see Note 4) and subcircuit Figure 72 were generated using the TLE207x typical electrical and
operating characteristics at T = 25°C. Using this information, output simulations of the following key parameters
A
can be generated to a tolerance of 20% (in most cases):
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
D
D
D
D
D
D
Unity-gain frequency
Common-mode rejection ratio
Phase margin
Quiescent power dissipation
Input bias current
DC output resistance
AC output resistance
Short-circuit output current limit
Open-loop voltage amplification
NOTE 4: G.R. Boyle, B.M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
99
3
EGND
+
−
DLN
V
CC+
92
9
FB
+
91
+
90
RSS
ISS
RO2
−
+
−
VB
DLP
RP
VLP
VLN
HLIM
−
+
−
2
10
+
−
VC
IN−
IN+
R2
C2
J1
J2
7
DP
6
53
+
−
1
VLIM
11
DC
12
GA
GCM
8
C1
RD2
RO1
RD1
4
DE
5
54
V
CC−
−
+
VE
OUT
R2
6
4
9
100.0E3
3.003E3
3.003E3
80
.SUBCKT TLE2074 1 2 3 4 5
RD1
11
12
5
C1
11
6
12
7
2.2E−12
RD2
R01
R02
RP
4
C2
10.00E−12
8
DC
5
53
5
DX
DX
DX
DX
DX
7
99
4
80
DE
54
90
92
4
3
27.30E3
500.0E3
DC 0
DLP
DLN
DP
91
90
3
RSS
VB
10
9
99
0
VC
3
53
4
DC 2.20
DC 2.20
DC 0
EGND
FB
99
7
0
99
POLY (2) (3,0) (4,0) 0 .5 .5
POLY (5) VB VC VE VLP VLN 0
VE
54
7
VLIM
VLP
VLN
8
+ 5.607E6 −6E6 6E6 6E6 −6E6
91
0
0
DC 45
DC 45
GA
6
0
3
0
6
10
0
11 12 333.0E−6
10 99 7.43E−9
DC 400.0E−6
VLIM 1K
10 JX
10 JX
92
GCM
ISS
HLIM
J1
.MODEL DX D (IS=800.0E−18)
.MODEL JX PJF (IS=15.00E−12 BETA=554.5E−6
90
11
12
+ VTO=−.6)
.ENDS
2
1
J2
Figure 72. Boyle Macromodel and Subcircut
PSpice and Parts are trademarks of MicroSim Corporation.
38
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TLE2071AQDRG4Q1
TLE2071AQDRQ1
TLE2071QDRG4Q1
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
TLE2071QDRQ1
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
8
TBD
Call TI
Call TI
TLE2072AQDRG4Q1
2500
2500
2500
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
TLE2072AQDRQ1
TLE2072QDRG4Q1
TLE2072QDRQ1
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
D
D
D
8
8
8
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLE2071-Q1, TLE2071A-Q1, TLE2072-Q1, TLE2072A-Q1 :
Catalog: TLE2071, TLE2071A, TLE2072, TLE2072A
•
Military: TLE2071M, TLE2071AM, TLE2072M, TLE2072AM
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Military - QML certified for Military and Defense Applications
•
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明