TLV1117-18IKCS_技术文档

ꢀ

ꢁ

ꢂ

ꢃ

ꢄ

ꢅ

ꢆ

ꢇ

ꢈ

ꢉ

ꢀ

ꢅ

ꢊ

ꢁ

ꢋ

ꢅꢌ

ꢆ

ꢍ

ꢎ

ꢏ

ꢋ

ꢆ

ꢁ

ꢐ

ꢑ

ꢒ

ꢆ

ꢓ

ꢐ

ꢔ

ꢐ

ꢈ

ꢀ

ꢂ

ꢐ

ꢁ

ꢀ

ꢅ

ꢕ

ꢋ

ꢓ

ꢋ

ꢕ

ꢈ

ꢁ

ꢅ

ꢀ

ꢐ

ꢓ

ꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

D

1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V, and Adjustable

Output Voltage Options

D

Specified Dropout Voltage at Multiple

Current Levels

D

Output Current of 800 mA

D

0.2% Line Regulation Maximum

0.4% Load Regulation Maximum

D

Operates Down to 1.1-V Dropout

D

DRJ (QFN) PACKAGE

(TOP VIEW)

KCS (TO-220) PACKAGE

(TOP VIEW)

DCY (SOT-223) PACKAGE

(TOP VIEW)

INPUT

OUTPUT

ADJ/GND

INPUT

ADJ

8

NC

V

1

†

V

‡

2

3

4

7

6

5

OUTPUT

ADJ/GND

IN

OUT

V

OUT

†

V

IN

OUT

†

V

‡

IN

OUT

†

‡

V

pins (2, 3, 4) must be connected together.

IN

pins (5, 6, 7) must be connected together.

OUT

KTT (TO-263) PACKAGE

(TOP VIEW)

KTE (PowerFLEXE) PACKAGE

KTP (PowerFLEXE/TO-252) PACKAGE

(TOP VIEW)

INPUT

IN

OUTPUT

ADJ/GND

OUTPUT

ADJ/GND

OUT

ADJ/GND

description/ordering information

The TLV1117 is a positive low-dropout voltage regulator, designed to provide up to 800 mA of output current.

The device is available in 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V, and adjustable output voltage options. All internal circuitry

is designed to operate down to 1-V input-to-output differential. Dropout voltage is specified at a maximum of

1.3 V at 800 mA, decreasing at lower load currents.

The low-profile surface-mount KTP package allows the device to be used in applications where space is limited.

The TLV1117 requires a minimum of 10 mF of output capacitance for stability. Output capacitors of this size or

larger normally are included in most regulator designs.

Unlike pnp-type regulators, where up to 10% of the output current is wasted as quiescent current, the quiescent

current of the TLV1117 flows into the load, increasing efficiency.

The TLV1117C device is characterized for operation over the virtual junction temperature range of 0°C to 125°C,

and the TLV1117I device is characterized for operation over the virtual junction temperature range of −40°C to

125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PowerFLEX is a trademark of Texas Instruments.

ꢔ

ꢓ

ꢐ

ꢦ

ꢆ

ꢡ

ꢈ

ꢖ

ꢟ

ꢀ

ꢠ

ꢎ

ꢚ

ꢐ

ꢘ

ꢌ

ꢙ

ꢆ

ꢅ

ꢀ

ꢅ

ꢗ

ꢘ

ꢢ

ꢙ

ꢚ

ꢠ

ꢛ

ꢜ

ꢝ

ꢞ

ꢗ

ꢚ

ꢘ

ꢗ

ꢟ

ꢣ

ꢠ

ꢡ

ꢛ

ꢢ

ꢘ

ꢞ

ꢝ

ꢜ

ꢟ

ꢚ

ꢙ

ꢣ

ꢀꢢ

ꢡ

ꢤ

ꢟ

ꢥ

ꢗ

ꢠ

ꢝ

ꢟ

ꢞ

ꢗ

ꢞ

ꢚ

ꢛ

ꢘ

ꢡ

ꢦ

ꢝ

ꢘ

ꢞ

ꢢ

ꢟ

ꢧ

Copyright  2005, Texas Instruments Incorporated

ꢛ

ꢚ

ꢠ

ꢞ

ꢚ

ꢛ

ꢜ

ꢞ

ꢚ

ꢟ

ꢣ

ꢗ

ꢙ

ꢗ

ꢠ

ꢢ

ꢛ

ꢞ

ꢨ

ꢞ

ꢢ

ꢛ

ꢚ

ꢙ

ꢩ

ꢝ

ꢎ

ꢘ

ꢜ

ꢢ

ꢟ

ꢞ

ꢝ

ꢘ

ꢦ

ꢝ

ꢛ

ꢦ

ꢪ

ꢝ

ꢞ ꢢ ꢟ ꢞꢗ ꢘꢬ ꢚꢙ ꢝ ꢥꢥ ꢣꢝ ꢛ ꢝ ꢜ ꢢ ꢞ ꢢ ꢛ ꢟ ꢧ

ꢛ

ꢝ

ꢘ

ꢞ

ꢫ

ꢧ

ꢔ

ꢛ

ꢚ

ꢦ

ꢡ

ꢠ

ꢞ

ꢗ

ꢚ

ꢘ

ꢣ

ꢛ

ꢚ

ꢠ

ꢢ

ꢟ

ꢗ

ꢘ

ꢬ

ꢦ

ꢚ

ꢢ

ꢟ

ꢘ

ꢚ

ꢞ

ꢘ

ꢢ

ꢠ

ꢢ

ꢟ

ꢝ

ꢛ

ꢗ

ꢥ

ꢫ

ꢗ

ꢘ

ꢠ

ꢥ

ꢡ

ꢦ

ꢢ

1

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀ ꢁꢂ ꢃꢃꢃ ꢄ

ꢅ ꢆꢇꢈ ꢉꢀꢅ ꢊ ꢁꢋ ꢅ ꢌꢆ ꢍꢎ ꢏ ꢋ ꢆ ꢁꢐ ꢑꢒꢆꢓ ꢐꢔ ꢐ ꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋ ꢕꢈꢁ ꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

description/ordering information (continued)

TLV1117C ORDERING INFORMATION

V

TYP

(V)

ORDERABLE

PART NUMBER

TOP-SIDE

MARKING

O

†

PACKAGE

T

J

QFN (DRJ)

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

TLV1117-15CDRJR

TLV1117-15CDCYR

TLV1117-15CKTTR

TLV1117-18CDRJR

TLV1117-18CDCYR

TLV1117-18CKTTR

TLV1117-25CDRJR

TLV1117-25CDCYR

TLV1117-25CKTTR

TLV1117-33CDRJR

TLV1117-33CDCYR

TLV1117-33CKTTR

TLV1117-50CDRJR

TLV1117-50CDCYR

TLV1117-50CKTTR

TLV1117CKTER

PREVIEW

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

PREVIEW

TLV1117C

TV1117

1.5 V

1.8 V

2.5 V

3.3 V

5 V

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

0°C to 125°C

SOT-223 (DCY)

TO-263 (KTT)

PowerFLEX (KTE)

‡

PowerFLEX/TO-252 (KTP) Reel of 2000

TLV1117CKTPR

QFN (DRJ)

Reel of 1000

Tube of 80

TLV1117CDRJR

PREVIEW

TLV1117CDCY

ADJ

SOT-223 (DCY)

V4

Reel of 2500

Tube of 50

TLV1117CDCYR

TO-220 (KCS)

TO-263 (KTT)

TLV1117CKCS

TLV1117C

Reel of 2000

TLV1117CKTTR

PREVIEW

†

‡

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at

www.ti.com/sc/package.

Complies with TO-252, variation AC.

2

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀꢁꢂ ꢃꢃꢃꢄ

ꢅꢆ ꢇ ꢈꢉꢀꢅꢊ ꢁ ꢋ ꢅꢌꢆ ꢍ ꢎꢏ ꢋꢆ ꢁ ꢐꢑꢒꢆꢓꢐ ꢔ ꢐꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋꢕ ꢈ ꢁꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

TLV1117I ORDERING INFORMATION

V

TYP

(V)

ORDERABLE

PART NUMBER

TOP-SIDE

MARKING

O

†

PACKAGE

T

J

QFN (DRJ)

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

Reel of 1000

Reel of 2500

Reel of 2000

TLV1117-15IDRJR

TLV1117-15IDCYR

TLV1117-15IKTTR

TLV1117-18IDRJR

TLV1117-18IDCYR

TLV1117-18IKTTR

TLV1117-25IDRJR

TLV1117-25IDCYR

TLV1117-25IKTTR

TLV1117-33IDRJR

TLV1117-33IDCYR

TLV1117-33IKTTR

TLV1117-50DRJR

TLV1117-50IDCYR

TLV1117-50IKTTR

TLV1117IKTER

PREVIEW

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

PREVIEW

TLV1117I

TY1117

1.5 V

1.8 V

2.5 V

3.3 V

5 V

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

SOT-223 (DCY)

TO-263 (KTT)

QFN (DRJ)

−40°C to 125°C

SOT-223 (DCY)

TO-263 (KTT)

PowerFLEX (KTE)

‡

PowerFLEX/TO-252 (KTP) Reel of 2000

TLV1117IKTPR

QFN (DRJ)

Reel of 1000

Tube of 80

TLV1117IDRJR

PREVIEW

ADJ

TLV1117IDCY

SOT-223 (DCY)

V2

Reel of 2500

Tube of 50

TLV1117IDCYR

TO-220 (KCS)

TO-263 (KTT)

TLV1117IKCS

TLV1117I

Reel of 2000

TLV1117IKTTR

PREVIEW

†

‡

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at

www.ti.com/sc/package.

Complies with TO-252, variation AC.

3

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀ ꢁꢂ ꢃꢃꢃ ꢄ

ꢅ ꢆꢇꢈ ꢉꢀꢅ ꢊ ꢁꢋ ꢅ ꢌꢆ ꢍꢎ ꢏ ꢋ ꢆ ꢁꢐ ꢑꢒꢆꢓ ꢐꢔ ꢐ ꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋ ꢕꢈꢁ ꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

functional block diagram

V

IN

_

Thermal

Limit

+

Current

Limit

_

V

OUT

GND/ADJ (Fixed-Voltage Version)

GND/ADJ (Adjustable Version)

†

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)

Continuous input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V

Operating virtual junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C

Storage temperature range, T

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C

stg

†

Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

4

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀꢁꢂ ꢃꢃꢃꢄ

ꢅꢆ

ꢇ

ꢈꢉ

ꢀ

ꢅ

ꢊ

ꢁ

ꢋ

ꢅꢌ

ꢆ

ꢍ

ꢎꢏ

ꢋ

ꢆ

ꢁ

ꢐ

ꢑ

ꢒ

ꢆ

ꢓ

ꢐ

ꢔ

ꢐ

ꢈ

ꢀ

ꢂ

ꢐ

ꢁ

ꢀ

ꢅ

ꢕ

ꢋ

ꢓ

ꢋ

ꢕ

ꢈ

ꢁ

ꢅ

ꢀ

ꢐ

ꢓ

ꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

package thermal data (see Note 1)

†

PACKAGE

PowerFLEX (KTE)

PowerFLEX/TO-252 (KTP)

QFN (DRJ)

BOARD

q

JP

JC

JA

High K, JESD 51-5

High K, JESD 51-7

High K, JESD 51-5

2.7°C/W

3°C/W

TBD

23°C/W

28°C/W

TBD

SOT (DCY)

4°C/W

53°C/W

TBD

TO-263 (KTT)

TBD

TO-220 (KCS)

3°C/W

19°C/W

†

For packages with exposed thermal pads, such as QFN, PowerPAD, and PowerFLEX, θ is defined as the thermal resistance between the die

junction and the bottom of the exposed pad.

JP

NOTE 1: Maximum power dissipation is a function of T (max), θ , and T . The maximum allowable power dissipation at any allowable ambient

J

JA

A

temperature is P = (T (max) − T )/θ . Operating at the absolute maximum T of 150°C can affect reliability.

D

J

A

JA

J

recommended operating conditions

†

MIN

MAX

15

UNIT

TLV1117

2.7

2.9

3.2

3.9

4.7

6.4

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

15

V

IN

Input voltage

V

15

I

Output current

0.8

125

A

OUT

TLV1117C

TLV1117I

0

T

Operating virtual junction temperature range

°C

J

−40

†

The input-to-output differential across the regulator should provide for some margin against regulator operation at the maximum dropout (for a

particular current value). This margin is needed to account for tolerances in both the input voltage (lower limit) and the output voltage (upper limit).

The absolute minimum V for a desired maximum output current can be calculated by the following:

IN

V

= V

OUT(max)

+ V

DO(max @ rated current)

IN(min)

5

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀ ꢁꢂ ꢃꢃꢃ ꢄ

ꢅ ꢆꢇꢈ ꢉꢀꢅ ꢊ ꢁꢋ ꢅ ꢌꢆ ꢍꢎ ꢏ ꢋ ꢆ ꢁꢐ ꢑꢒꢆꢓ ꢐꢔ ꢐ ꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋ ꢕꢈꢁ ꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

TLV1117C electrical characteristics, T = 0°C to 125°C, all typical values are at T = 25°C (unless

J

otherwise noted)

†

PARAMETER

TEST CONDITIONS

MIN

1.238

1.225

1.485

1.47

TYP

1.25

1.5

1.8

2.5

3.3

5

MAX

1.262

1.27

1.515

1.53

1.818

1.836

2.525

2.55

3.333

3.365

5.05

5.1

UNIT

V

− V

OUT

= 2 V, I = 10 mA, T = 25°C

OUT J

IN

TLV1117

I

= 10 mA to 800 mA, V − V = 1.4 V to 10 V

IN OUT

OUT

V

= 3.5 V, I = 10 mA, T = 25°C

OUT J

IN

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

= 2.9 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

= 3.8 V, I

OUT

1.782

1.764

2.475

2.45

IN

J

= 3.2 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

Output voltage, V

V

OUT

= 4.5 V, I

OUT

IN

J

= 3.9 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

= 5 V, I

OUT

3.267

3.235

4.95

IN

J

= 4.75 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

= 7 V, I

OUT

IN

J

= 6.5 V to 12 V, I

OUT

= 0 to 800 mA

= 1.5 V to 13.75 V

4.9

5

IN

I

= 10 mA, V − V

IN OUT

TLV1117

0.035

1

0.2

%

OUT

= 0 mA, V = 2.9 V to 10 V

IN

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

TLV1117

6

= 0 mA, V = 3.2 V to 10 V

IN

1

6

Line regulation

Load regulation

= 0 mA, V = 3.9 V to 10 V

IN

1

6

mV

%

= 0 mA, V = 4.75 V to 15 V

IN

1

6

= 0 mA, V = 6.5 V to 15 V

IN

1

10

= 10 mA to 800 mA, V − V

IN OUT

= 3 V

0.2

1

0.4

= 0 to 800 mA, V = 2.9 V

IN

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

10

= 0 to 800 mA, V = 3.2 V

IN

1

10

= 0 to 800 mA, V = 3.9 V

IN

1

10

mV

V

= 0 to 800 mA, V = 4.75 V

IN

1

10

= 0 to 800 mA, V = 6.5 V

IN

1

15

= 100 mA

= 500 mA

1.1

1.15

1.2

1.7

1.2

Dropout voltage, V

(see Note 2)

DO

1.25

1.3

= 800 mA

− V = 5 V, T = 25°C

‡

Current limit

V

0.8

1.5

A

IN

OUT

J

Minimum load current

V

= 15 V

TLV1117

5

mA

All

Quiescent current

V

IN

≤ 15 V

fixed-voltage

options

5

10

mA

Thermal regulation

Ripple rejection

30 ms pulse, T = 25°C

0.01

78

0.1

%/W

dB

A

V

IN

− V

OUT

= 3 V, V

ripple

= 1 V , f = 120 Hz

pp

60

†

All characteristics are measured with a 10-µF capacitor across the input and a 10-µF capacitor across the output. Pulse testing techniques are

used to maintain the junction temperature as close to the ambient temperature as possible.

Current limit test specified under recommended operating conditions

‡

NOTE 2: Dropout is defined as the V

to V

differential at which V

OUT OUT

drops 100 mV below the value of V

, measured at

OUT

IN

V

IN

= V + 1.5 V.

OUT(nom)

6

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀꢁꢂ ꢃꢃꢃꢄ

ꢅꢆ ꢇ ꢈꢉꢀꢅꢊ ꢁ ꢋ ꢅꢌꢆ ꢍ ꢎꢏ ꢋꢆ ꢁ ꢐꢑꢒꢆꢓꢐ ꢔ ꢐꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋꢕ ꢈ ꢁꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

TLV1117C electrical characteristics, T = 0°C to 125°C, all typical values are at T = 25°C (unless

J

otherwise noted) (continued)

†

PARAMETER

TEST CONDITIONS

MIN

TYP

80

MAX

120

5

UNIT

µA

%

ADJUSTMENT pin current

Change in ADJUSTMENT pin current

Temperature stability

I

= 10 mA to 800 mA, V − V

IN OUT

= 1.4 V to 10 V

0.2

OUT

T = full range

0.5

J

Long-term stability

1000 hrs, No load, T = 125°C

0.3

%

A

Output noise voltage (% of V

)

f = 10 Hz to 100 kHz

0.003

%

OUT

†

All characteristics are measured with a 10-µF capacitor across the input and a 10-µF capacitor across the output. Pulse testing techniques are

used to maintain the junction temperature as close to the ambient temperature as possible.

7

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀ ꢁꢂ ꢃꢃꢃ ꢄ

ꢅ ꢆꢇꢈ ꢉꢀꢅ ꢊ ꢁꢋ ꢅ ꢌꢆ ꢍꢎ ꢏ ꢋ ꢆ ꢁꢐ ꢑꢒꢆꢓ ꢐꢔ ꢐ ꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋ ꢕꢈꢁ ꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

TLV1117I electrical characteristics, T = -40°C to 125°C, all typical values are at T = 25°C (unless

J

otherwise noted)

†

PARAMETER

TEST CONDITIONS

MIN

1.238

1.2

TYP

1.25

1.5

1.8

2.5

3.3

5

MAX

1.262

1.29

1.515

1.56

1.818

1.872

2.525

2.6

UNIT

V

− V

OUT

= 2 V, I

= 10 mA, T = 25°C

IN

OUT J

TLV1117

I

= 10 mA to 800 mA, V − V

= 1.4 V to 10 V

= 10 mA, T = 25°C

OUT

IN OUT

V

= 3.5 V, I

OUT

1.485

1.44

IN

J

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

= 2.9 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

= 3.8 V, I

OUT

1.782

1.728

2.475

2.4

IN

J

= 3.2 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

Output voltage, V

V

OUT

= 4.5 V, I

OUT

IN

J

= 3.9 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

= 5 V, I

OUT

3.267

3.168

4.95

3.333

3.432

5.05

5.2

IN

J

= 4.75 V to 10 V, I

= 0 to 800 mA

= 10 mA, T = 25°C

IN

OUT

= 7 V, I

OUT

IN

J

= 6.5 V to 12 V, I

OUT

= 0 to 800 mA

= 1.5 V to 13.75 V

4.8

5

IN

I

= 10 mA, V − V

IN OUT

TLV1117

0.035

1

0.3

%

OUT

= 0 mA, V = 2.9 V to 10 V

IN

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

TLV1117

4.5

= 0 mA, V = 3.2 V to 10 V

IN

1

5.5

Line regulation

= 0 mA, V = 3.9 V to 10 V

IN

1

7.5

mV

%

= 0 mA, V = 4.75 V to 15 V

IN

1

10

= 0 mA, V = 6.5 V to 15 V

IN

1

15

= 10 mA to 800 mA, V − V

IN OUT

= 3 V

0.2

1

0.5

= 0 to 800 mA, V = 2.9 V

IN

TLV1117-15

TLV1117-18

TLV1117-25

TLV1117-33

TLV1117-50

7.5

= 0 to 800 mA, V = 3.2 V

IN

1

9

Load regulation

= 0 to 800 mA, V = 3.9 V

IN

1

12.5

15

mV

V

= 0 to 800 mA, V = 4.75 V

IN

1

= 0 to 800 mA, V = 6.5 V

IN

1

20

= 100 mA

= 500 mA

1.1

1.15

1.2

1.7

1.3

Dropout voltage, V

(see Note 2)

DO

1.35

1.4

= 800 mA

− V = 5 V, T = 25°C

‡

Current limit

V

0.8

60

1.5

A

IN

OUT

J

Minimum load current

V

= 15 V

TLV1117

5

mA

All fixed-

voltage

options

Quiescent current

V

IN

≤ 15 V

5

15

mA

Thermal regulation

Ripple rejection

30-ms pulse, T = 25°C

0.01

75

0.1

%/W

dB

A

V

IN

− V

OUT

= 3 V, V

ripple

= 1 V , f = 120 Hz

pp

†

All characteristics are measured with a 10-µF capacitor across the input and a 10-µF capacitor across the output. Pulse testing techniques are

used to maintain the junction temperature as close to the ambient temperature as possible.

Current limit test specified under recommended operating conditions

‡

NOTE 2: Dropout is defined as the V to V

differential at which V

OUT

drops 100 mV below the value of V , measured at

OUT

IN OUT

V

IN

= V + 1.5 V.

OUT(nom)

8

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀꢁꢂ ꢃꢃꢃꢄ

ꢅꢆ ꢇ ꢈꢉꢀꢅꢊ ꢁ ꢋ ꢅꢌꢆ ꢍ ꢎꢏ ꢋꢆ ꢁ ꢐꢑꢒꢆꢓꢐ ꢔ ꢐꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋꢕ ꢈ ꢁꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

TLV1117I electrical characteristics, T = 40°C to 125°C, all typical values are at T = 25°C (unless

J

otherwise noted) (continued)

†

PARAMETER

TEST CONDITIONS

MIN

TYP

80

MAX

120

10

UNIT

µA

%

ADJUSTMENT pin current

Change in ADJUSTMENT pin current

Temperature stability

I

= 10 mA to 800 mA, V − V

IN OUT

= 1.4 V to 10 V

0.2

OUT

T = full range

0.5

J

Long-term stability

1000 hrs, No load, T = 125°C

0.3

%

A

Output noise voltage (% of V

)

f = 10 Hz to 100 kHz

0.003

%

OUT

†

All characteristics are measured with a 10-µF capacitor across the input and a 10-µF capacitor across the output. Pulse testing techniques are

used to maintain the junction temperature as close to the ambient temperature as possible.

9

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀ ꢁꢂ ꢃꢃꢃ ꢄ

ꢅ ꢆꢇꢈ ꢉꢀꢅ ꢊ ꢁꢋ ꢅ ꢌꢆ ꢍꢎ ꢏ ꢋ ꢆ ꢁꢐ ꢑꢒꢆꢓ ꢐꢔ ꢐ ꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋ ꢕꢈꢁ ꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

TYPICAL CHARACTERISTICS

(GRAPHS PREVIEW)

Figure 1. Short-Circuit Current vs (V − V

)

IN

OUT

Figure 2. Load Regulation vs Temperature

Figure 3. Ripple Rejection vs Frequency (ADJ Version)

Figure 4. Ripple Rejection vs Current (ADJ Version)

Figure 5. Temperature Stability

Figure 6. ADJ Pin Current vs Temperature

Figure 7. TLV1117-25 Load Transient Response

Figure 8. TLV1117-25 Line Transient Response

Figure 9. TLV1117-33 Load Transient Response

Figure 10. TLV1117-33 Line Transient Response

10

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

ꢀꢁꢂ ꢃꢃꢃꢄ

ꢅꢆ ꢇ ꢈꢉꢀꢅꢊ ꢁ ꢋ ꢅꢌꢆ ꢍ ꢎꢏ ꢋꢆ ꢁ ꢐꢑꢒꢆꢓꢐ ꢔ ꢐꢈꢀ ꢂꢐ ꢁꢀꢅꢕ ꢋ ꢓꢋꢕ ꢈ ꢁꢅꢀꢐ ꢓꢉ

SLVS561A − DECEMBER 2004 – REVISED MARCH 2005

APPLICATION INFORMATION

1N4002 (See Note D)

TLV1117 − ADJ

INPUT

ADJ/GND

ADJ

OUTPUT

V

O

V

I

R1

V

REF

10 µF

I

(see Note C)

100 µF

(see Note A)

C

ADJ

(see Note B)

R2

V

^{is calculated}ǒ^as:

Ǔ

OUT

R2

R1

V_OUT+ V_REF1 )

) (I_ADJ R2)

Because I

typically is 55 µA, it is negligible in most applications.

ADJ

NOTES: A. Output capacitor selection is critical for regulator stability. The recommended minimum is 10-µF tantalum or 50-µF aluminum

electrolytic, with either one having an ESR between 0.3 Ω and 22 Ω. Larger C

values benefit the regulator by improving

1

OUT

transient response and loop stability.

B.

C.

C

can be used to improve ripple rejection. Ensure that the impedance of C ǒ_X

Ǔ

is < R1 to

+

ADJ

CADJ

2pf_rippleC_ADJ

prevent the ripple from being amplified. If C

required (22-µF tantalum or 150-µF aluminum electrolytic).

is used, then a larger C

is

ADJ

OUT

C

is recommended if TLV1117 is not located near the power-supply filter.

IN

D. An external diode is recommended to protect the regulator if the input instantaneously is shorted to GND.

Figure 11. Basic Adjustable Regulator

11

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PACKAGE OPTION ADDENDUM

www.ti.com

30-Mar-2005

PACKAGING INFORMATION

Orderable Device

Status ⁽¹⁾

Package Package

Type

Pins Package Eco Plan ⁽²⁾Lead/Ball Finish MSL Peak Temp ⁽³⁾

Qty

Drawing

DCY

KCS

DCY

KCS

DCY

KCS

DCY

KCS

KTP

DCY

KC

TLV1117-15CDCY

TLV1117-15CDCYR

TLV1117-15CKCS

TLV1117-15IDCY

TLV1117-15IDCYR

TLV1117-15IKCS

TLV1117-18CDCY

TLV1117-18CDCYR

TLV1117-18CKCS

TLV1117-18IDCY

TLV1117-18IDCYR

TLV1117-18IKCS

TLV1117-25CKTPR

TLV1117-33CDCY

TLV1117-33CDCYR

TLV1117-33CKC

TLV1117-33CKCS

TLV1117-33CKTT

PREVIEW

SOT-223

TO-220

SOT-223

TO-220

SOT-223

TO-220

SOT-223

TO-220

PFM

4

3

4

3

4

3

4

3

2

4

3

80

2500

50

TBD

Call TI

80

2500

50

80

2500

50

80

2500

50

3000

80

SOT-223

TO-220

2500

50

KCS

KTT

50

DDPAK/

TO-263

50

TLV1117-33CKTTR

PREVIEW

DDPAK/

TO-263

KTT

3

1000

TBD

Call TI

TLV1117-33DCY

TLV1117-33IKCS

TLV1117-50CDCY

TLV1117-50CKCS

TLV1117-50CKTER

TLV1117-50CKTPR

TLV1117-50CKTT

PREVIEW

SOT-223

TO-220

SOT-223

TO-220

PFM

DCY

KCS

DCY

KCS

KTE

KTP

KTT

4

3

4

3

2

3

80

50

TBD

Call TI

80

50

2000

3000

50

PFM

DDPAK/

TO-263

TLV1117-50CKTTR

PREVIEW

DDPAK/

TO-263

KTT

3

TBD

Call TI

TLV1117-50DCYR

TLV1117CDCY

TLV1117CDCYR

TLV1117CKC

PREVIEW

ACTIVE

PREVIEW

ACTIVE

SOT-223

TO-220

PFM

DCY

KC

4

3

2

4

3

2

2500

80

TBD

Call TI

CU

Call TI

Level-2-235C-1 YEAR

Call TI

2500

50

CU

Call TI

CU

TLV1117CKCS

TLV1117CKTER

TLV1117CKTPR

TLV1117IDCY

TLV1117IDCYR

TLV1117IKCS

KCS

KTE

KTP

DCY

KCS

KTE

KTP

50

Level-NC-NC-NC

Level-1-220C-UNLIM

Level-2-235C-1 YEAR

Level-NC-NC-NC

Level-1-220C-UNLIM

2000

3000

80

PFM

SOT-223

TO-220

PFM

2500

50

CU

Call TI

TLV1117IKTER

TLV1117IKTPR

2000

3000

PFM

Addendum-Page 1

PACKAGE OPTION ADDENDUM

www.ti.com

30-Mar-2005

⁽¹⁾The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in

a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2)

Eco Plan

-

The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS

&

no Sb/Br)

-

please check

http://www.ti.com/productcontent for the latest availability information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements

for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered

at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame

retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3)

MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder

temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is

provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the

accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take

reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on

incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited

information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI

to Customer on an annual basis.

Addendum-Page 2

MECHANICAL DATA

MPDS094A – APRIL 2001 – REVISED JUNE 2002

DCY (R-PDSO-G4)

PLASTIC SMALL-OUTLINE

6,70 (0.264)

6,30 (0.248)

3,10 (0.122)

2,90 (0.114)

4

0,10 (0.004)

M

3,70 (0.146)

3,30 (0.130)

7,30 (0.287)

6,70 (0.264)

Gauge Plane

1

2

3

0,25 (0.010)

0,84 (0.033)

0,66 (0.026)

0°–10°

2,30 (0.091)

0,10 (0.004)

M

4,60 (0.181)

0,75 (0.030) MIN

1,70 (0.067)

1,50 (0.059)

1,80 (0.071) MAX

0,35 (0.014)

0,23 (0.009)

Seating Plane

0,08 (0.003)

0,10 (0.0040)

0,02 (0.0008)

4202506/B 06/2002

NOTES: A. All linear dimensions are in millimeters (inches).

B. This drawing is subject to change without notice.

C. Body dimensions do not include mold flash or protrusion.

D. Falls within JEDEC TO-261 Variation AA.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

MECHANICAL DATA

MPFM001E – OCTOBER 1994 – REVISED JANUARY 2001

KTE (R-PSFM-G3)

PowerFLEX PLASTIC FLANGE-MOUNT

0.375 (9,52)

0.365 (9,27)

0.080 (2,03)

0.070 (1,78)

0.360 (9,14)

0.350 (8,89)

0.050 (1,27)

0.040 (1,02)

0.220 (5,59)

NOM

0.010 (0,25) NOM

Thermal Tab

(See Note C)

0.360 (9,14)

0.350 (8,89)

0.295 (7,49)

NOM

0.320 (8,13)

0.310 (7,87)

0.420 (10,67)

0.410 (10,41)

1

3

0.025 (0,63)

0.031 (0,79)

Seating Plane

0.004 (0,10)

0.010 (0,25)

M

0.100 (2,54)

0.200 (5,08)

0.005 (0,13)

0.001 (0,03)

0.041 (1,04)

0.031 (0,79)

0.010 (0,25)

NOM

Gage Plane

3°–6°

0.010 (0,25)

4073375/F 12/00

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.

C. The center lead is in electrical contact with the thermal tab.

D. Dimensions do not include mold protrusions, not to exceed 0.006 (0,15).

E. Falls within JEDEC MO-169

PowerFLEX is a trademark of Texas Instruments.

1

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

MECHANICAL DATA

MPSF001F – JANUARY 1996 – REVISED JANUARY 2002

KTP (R-PSFM-G2)

PowerFLEX PLASTIC FLANGE-MOUNT PACKAGE

0.080 (2,03)

0.070 (1,78)

0.243 (6,17)

0.233 (5,91)

0.228 (5,79)

0.218 (5,54)

0.050 (1,27)

0.040 (1,02)

0.130 (3,30) NOM

0.010 (0,25) NOM

Thermal Tab

(See Note C)

0.215 (5,46)

0.287 (7,29)

0.277 (7,03)

NOM

0.247 (6,27)

0.237 (6,02)

0.381 (9,68)

0.371 (9,42)

0.100 (2,54)

0.090 (2,29)

0.032 (0,81) MAX

Seating Plane

0.004 (0,10)

0.090 (2,29)

0.180 (4,57)

0.005 (0,13)

0.001 (0,02)

0.031 (0,79)

0.025 (0,63)

0.010 (0,25)

M

0.047 (1,19)

0.037 (0,94)

0.010 (0,25) NOM

Gage Plane

0.010 (0,25)

2°–ā6°

4073388/M 01/02

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.

C. The center lead is in electrical contact with the thermal tab.

D. Dimensions do not include mold protrusions, not to exceed 0.006 (0,15).

E. Falls within JEDEC TO-252 variation AC.

PowerFLEX is a trademark of Texas Instruments.

1

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,

enhancements, improvements, and other changes to its products and services at any time and to discontinue

any product or service without notice. Customers should obtain the latest relevant information before placing

orders and should verify that such information is current and complete. All products are sold subject to TI’s terms

and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in

accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI

deems necessary to support this warranty. Except where mandated by government requirements, testing of all

parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for

their products and applications using TI components. To minimize the risks associated with customer products

and applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,

copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process

in which TI products or services are used. Information published by TI regarding third-party products or services

does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.

Use of such information may require a license from a third party under the patents or other intellectual property

of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of information in TI data books or data sheets is permissible only if reproduction is without

alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction

of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for

such altered documentation.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that

product or service voids all express and any implied warranties for the associated TI product or service and

is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Following are URLs where you can obtain information on other Texas Instruments products and application

solutions:

Products

Applications

Audio

Amplifiers

amplifier.ti.com

www.ti.com/audio

Data Converters

dataconverter.ti.com

Automotive

www.ti.com/automotive

DSP

dsp.ti.com

Broadband

Digital Control

Military

www.ti.com/broadband

www.ti.com/digitalcontrol

www.ti.com/military

Interface

Logic

interface.ti.com

logic.ti.com

Power Mgmt

Microcontrollers

power.ti.com

Optical Networking

Security

www.ti.com/opticalnetwork

www.ti.com/security

www.ti.com/telephony

www.ti.com/video

microcontroller.ti.com

Telephony

Video & Imaging

Wireless

www.ti.com/wireless

Mailing Address:

Texas Instruments

Post Office Box 655303 Dallas, Texas 75265


型号：	TLV1117-18IKCS
厂家：	TEXAS INSTRUMENTS
描述：	ADJUSTABLE AND FIXED LOW DROPOUT VOLTAGE REGULATORS 可调，固定低压差稳压器稳压器
文件：	总20页 (文件大小：500K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TLV1117-18IKCS [TI]

相关型号：

TLV1117-18IKTPR

TLV1117-18IKTTR

TLV1117-18IKVUR

TLV1117-18IKVURG3

TLV1117-25

TLV1117-25CDCY

TLV1117-25CDCYG3

TLV1117-25CDCYR

TLV1117-25CDCYRG3

TLV1117-25CDRJR

TLV1117-25CDRJRG4

TLV1117-25CKCS