TLV320AIC32IRHBG4_技术文档

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Low-Power Stereo Audio CODEC for Portable Audio/Telephony

1

FEATURES

•

Low Power: 14-mW Stereo, 48-kHz Playback

With 3.3-V Analog Supply

•

Stereo Audio DAC

•

Programmable Input/Output Analog Gains

Automatic Gain Control (AGC) for Record

Programmable Microphone Bias Level

–

100 dB A Signal-to-Noise Ratio

16/20/24/32-Bit Data

Supports Rates From 8 kHz to 96 kHz

3D/Bass/Treble/EQ/De-Emphasis Effects

Programmable PLL for Flexible Clock

Generation

I²C Control Bus

Audio Serial Data Bus Supports I²S,

•

Stereo Audio ADC

•

–

92 dB A Signal-to-Noise Ratio

Supports Rates From 8 kHz to 96 kHz

Left/Right-Justified, DSP, and TDM Modes

•

Six Audio Input Pins

Six Stereo Single-Ended Inputs

Six Audio Output Drivers

•

Extensive Modular Power Control

Power Supplies:

–

Analog: 2.7 V – 3.6 V

–

Stereo 8-Ω, 500 mw/Channel Speaker Drive

Capability

Digital Core: 1.65 V – 1.95 V

Digital I/O: 1.1 V – 3.6 V

Stereo Fully-Differential or Single-Ended

Headphone Drivers

•

Available Packages: 5 × 5 mm, 32-Pin QFN

Fully Differential Stereo Line Outputs

DESCRIPTION

The TLV320AIC32 is a low-power stereo-audio codec with a stereo headphone amplifier, as well as multiple

inputs and outputs, programmable in single-ended or fully-differential configurations. Extensive register- based

power control is included, enabling stereo 48-kHz DAC playback as low as 14 mW from a 3.3-V analog supply,

making it ideal for portable, battery-powered audio and telephony applications.

The record path of the TLV320AIC32 contains integrated microphone bias, digitally-controlled stereo-microphone

pre-amp, and automatic gain control (AGC), with mix/mux capability among the multiple analog inputs. The

playback path includes mix/mux capability from the stereo DAC and selected inputs, through programmable

volume controls, to the various outputs.

The TLV320AIC32 contains four high-power output drivers as well as two fully differential output drivers. The

high-power output drivers are capable of driving a variety of load configurations, including up to four channels of

single-ended 16-Ω headphones using ac-coupling capacitors, or stereo 16-Ω headphones in a cap-less output

configuration. In addition, pairs of drivers can be used to drive 8-Ω speakers in a BTL configuration at 500 mW

per channel.

The stereo audio DAC supports sampling rates from 8 kHz to 96 kHz and includes programmable digital filtering

in the DAC path for 3D, bass, treble, midrange effects, speaker equalization, and de-emphasis for 32 kHz, 44.1

kHz, and 48 kHz rates. The stereo-audio ADC supports sampling rates from 8 kHz to 96 kHz and is preceded by

programmable gain amplifiers providing up to +59.5 dB analog gain for low-level microphone inputs.

The serial control bus supports the I²C protocol, while the serial-audio data bus is programmable for I²S, left/right

justified, DSP, or TDM modes. A highly programmable PLL is included for flexible clock generation and support

for all standard audio rates from a wide range of available MCLKs, varying from 512 kHz to 50 MHz, with special

attention paid to the most popular cases of 12 MHz, 13 MHz, 16 MHz, 19.2 MHz, and 19.68 MHz system clocks.

The TLV320AIC32 operates from an analog supply of 2.7 V – 3.6 V, a digital core supply of 1.65 V – 1.95 V, and

a digital I/O supply of 1.1 V – 3.6 V. The device is available in a 5 × 5 mm, 32-lead QFN package.

1

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

SIMPLIFIED BLOCK DIAGRAM

+

HPL+

Audio Serial

Voltage Supplies

Bus

MIC2/LINE2L

HPL-/HPLCOM

VCM

+

MIC3/LINE3L

PGA

0/+59.5dB

0.5dB

steps

Volume Ctl

& Effects

DAC

L

MIC1/LINE1L

ADC

+

VCM

PGA

0/+59.5dB

0.5dB

HPR-/HPRCOM/

SPKFC

Volume Ctl

& Effects

DAC

R

MIC1/LINE1R

MIC3/LINE3R

steps

HPR+

+

MIC2/LINE2R

2

LINE_OUT_L+

LINE_OUT_L-

Bias/

Reference

Audio Clock

Generation

I

C Control

Bus

+

LINE_OUT_R+

LINE_OUT_R-

Figure 1. Simplified Codec Block Diagram

PACKAGE/ORDERING INFORMATION

OPERATING

TEMPERATURE

RANGE

PACKAGE

DESIGNATOR

TRANSPORT

MEDIA, QUANTITY

PRODUCT

TLV320AIC32

PACKAGE

QFN-32

ORDERING NUMBER

RHB

–40°C to 85°C

TLV320AIC32IRHBT

TLV320AIC32IRHBR

Tape and Reel, 250

Tape and Reel, 3000

2

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

DEVICE INFORMATION

PIN ASSIGNMENTS

1

8

32

9

TLV320AIC32

25

16

24

17

Table 1. TERMINAL FUNCTIONS

TERMINAL

QFN NO.

DESCRIPTION

NAME

I/O

MCLK

1

I

I/O

I

Master clock input

BCLK

2

Audio serial data bus bit clock input/output

Audio serial data bus word clock input/output

Audio serial data bus data input

Audio serial data bus data output

Digital core / I/O Ground Supply, 0 V

Digital I/O voltage supply, 1.1 V – 3.6 V

I2C serial clock input

WCLK

3

DIN

4

DOUT

5

O

I/O

I

DVSS

6

IOVDD

7

SCL

8

SDA

9

I2C serial data input/output

MIC1L/LINE1L

MIC1R/LINE1R

MIC2L/LINE2L

MIC2R/LINE2R

MIC3L/LINE3L

MICBIAS

MIC3R/LINE3R

AVSS1

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

Left input 1

I

Right input 1

I

Left input 2

I

Right input 2

I

Left input 3

O

I

Microphone bias voltage output

Right input 3

I

Analog ADC ground supply, 0 V

Analog ADC and output driver voltage supply, 2.7 V – 3.6 V

High power output driver (left +)

High power output driver (left - or multi-functional)

Analog output driver ground supply, 0 V

High power output driver (right - or multi-functional)

High power output driver (right +)

Analog output driver voltage supply, 2.7 V – 3.6 V

Analog DAC voltage supply, 2.7 V – 3.6 V

DRVDD

O

I

HPLOUT

HPLCOM

DRVSS

HPRCOM

HPROUT

DRVDD

AVDD

Submit Documentation Feedback

3

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Table 1. TERMINAL FUNCTIONS (continued)

TERMINAL

DESCRIPTION

NAME

QFN NO.

I/O

I

AVSS2

26

27

28

29

30

31

32

Analog DAC ground supply, 0 V

Left line output (+)

LEFT_LOP

LEFT_LOM

RIGHT_LOP

RIGHT_LOM

RESET

O

Left line output (-)

Right lineo output (+)

Right line output (-)

Reset

DVDD

I

Digital core voltage supply, 1.65 V – 1.95 V

ABSOLUTE MAXIMUM RATINGS

over operating free-air temperature range (unless otherwise noted)⁽¹⁾

VALUE

–0.3 to 3.9

UNIT

V

AVDD to AVSS1/2, DRVDD to DRVSS

AVDD to DRVSS

–0.3 to 3.9

V

IOVDD to DVSS

–0.3 to 3.9

V

DVDD to DVSS

–0.3 to 2.5

V

AVDD to DRVDD

–0.1 to 0.1

V

Digital input voltage to DVSS

Analog input voltage to AVSS1/2

Operating temperature range

Storage temperature range

–0.3 V to IOVDD+0.3

–0.3 V to AVDD+0.3

-40 to +85

V

°C

-65 to +105

105

T_JMax

Junction temperature

Power dissipation

(T_JMax – T_A) / θ_JA

44

θ_JA

Thermal impedance

°C/W

(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating

conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

DISSIPATION RATINGS⁽¹⁾

T_A= 25°C

POWER RATING

T_A= 75°C

POWER RATING

T_A= 85°C

POWER RATING

DERATING FACTOR

1.82 W

22.7 mW/°C

681 mW

454 mW

(1) This data was taken using 2 oz. trace and copper pad that is soldered directly to a JEDEC standard 4-layer 3 in × 3 in PCB.

RECOMMENDED OPERATING CONDITIONS

over operating free-air temperature range (unless otherwise noted)

MIN

NOM

MAX

UNIT

AVDD,

Analog supply voltage

2.7

3.3

3.6

V

DRVDD1/2⁽¹⁾

DVDD⁽¹⁾

IOVDD⁽¹⁾

V_I

Digital core supply voltage

1.65

1.1

1.8

1.95

3.6

V

Digital I/O supply voltage

Analog full-scale 0dB input voltage (DRVDD1 = 3.3 V)

Stereo line-output load resistance

Stereo headphone-output load resistance

Digital output load capacitance

0.707

V_RMS

kΩ

Ω

10

16

10

pF

°C

T_A

Operating free-air temperature

–40

85

(1) Analog voltage values are with respect to AVSS1, AVSS2, DRVSS; digital voltage values are with respect to DVSS.

Submit Documentation Feedback

4

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

ELECTRICAL CHARACTERISTICS

At 25°C, AVDD, DRVDD, IOVDD = 3.3 V, DVDD = 1.8 V, Fs = 48-kHz, 16-bit audio data (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

AUDIO ADC

Input signal level (0-dB)

Signal-to-noise ratio,

Single-ended input

0.707

92

V_RMS

dB

Fs = 48 kHz, 0 dB PGA gain, MIC1/LINE1 inputs

selected and AC-shorted to ground

80

(2)

A-weighted⁽¹⁾

Dynamic range,

Fs = 48 kHz, 1-kHz –60 dB full-scale input applied at

MIC1/LINE1 inputs, 0-dB PGA gain

92

dB

(2)

A-weighted⁽¹⁾

–90

0.003%

46

–75

Fs = 48 kHz, 1-kHz –2dB full-scale input applied at

MIC1/LINE1 inputs, 0-dB PGA gain

THD

Total harmonic distortion

0.017%

Power supply rejection ratio

234 Hz, 100 mVpp on AVDD, DRVDD

1 kHz, –2 dB MIC3L to MIC3R

1 kHz, –2 dB MIC2L to MIC2R

1 kHz, –2 dB MIC1L to MIC1R

1 kHz input, 0 dB PGA gain

dB

–80

ADC channel separation

ADC gain error

–99

–-73

0.7

dB

ADC programmable gain amplifier

maximum gain

1-kHz input tone, R_SOURCE< 50 Ω

59.5

0.5

20

ADC programmable gain amplifier

step size

dB

MIC1/LINE1 inputs, routed to single ADC

Input mix attenuation = 0 dB

MIC2/LINE2 inputs, input mix attenuation = 0 dB

MIC3/LINE3 inputs, input mix attenuation = 0 dB

20

MIC1/LINE1 inputs,

input mix attenuation = –12 dB

Input resistance

kΩ

80

MIC2/LINE2 inputs,

input mix attenuation = –12 dB

MIC3/LINE3 inputs,

input mix attenuation = –12 dB

80

10

0

Input capacitance

MIC1/LINE1 inputs

pF

dB

Input level control minimum

attenuation setting

Input level control maximum

attenuation setting

12

dB

Input level control attenuation step

size

1.5

ADC DIGITAL DECIMATION FILTER, Fs = 48 kHz

Filter gain from 0 to 0.39 Fs

Filter gain at 0.4125 Fs

±0.1

–0.25

–3

dB

Filter gain at 0.45 Fs

dB

Filter gain at 0.5 Fs

–17.5

–75

dB

Filter gain from 0.55 Fs to 64 Fs

Filter group delay

dB

17/Fs

Sec

MICROPHONE BIAS

2.0

2.5

Bias voltage

Programmable settings, load = 750 Ω

2.25

2.75

4

V

AVDD-0.2

Current sourcing

2.5 V setting

mA

(1) Ratio of output level with 1-kHz full-scale sine wave input, to the output level with the inputs short circuited, measured A-weighted over a

20-Hz to 20-kHz bandwidth using an audio analyzer.

(2) All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may

result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter

removes out-of-band noise, which, although not audible, may affect dynamic specification values.

Submit Documentation Feedback

5

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

ELECTRICAL CHARACTERISTICS (continued)

At 25°C, AVDD, DRVDD, IOVDD = 3.3 V, DVDD = 1.8 V, Fs = 48-kHz, 16-bit audio data (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

AUDIO DAC

Differential Line output, load = 10 kΩ, 50 pF

1.414

4.0

V_RMS

V_PP

0-dB gain to line outputs. DAC output common-mode

setting = 1.35 V, output level control gain = 0-dB

Full-scale differential output voltage

Fs = 48 kHz, 0-dB gain to line outputs, zero signal

applied, referenced to full-scale input level

Signal-to-noise ratio, A-weighted⁽³⁾

Dynamic range, A-weighted

90

100

dB

Fs = 48 kHz, 0-dB gain to line outputs,

1 kHz –60 dB signal applied

Total harmonic distortion

Fs = 48 kHz, 1 kHz 0 dB input signal applied

234 Hz, 100 mVpp on AVDD, DRVDD1/2

–93

81

–75

dB

Power supply rejection ratio

DAC channel separation (left to right) 1-kHz, 0-dB

–100

0.1

DAC interchannel gain mismatch

DAC Gain Error

1 kHz input, 0dB gain

–0.4

DAC DIGITAL INTERPOLATION

FILTER

Fs = 48-kHz

Passband

High-pass filter disabled

0.45×Fs

Hz

dB

Passband ripple

Transition band

Stopband

±0.06

0.45×Fs

0.55×Fs

7.5×Fs

Hz

Stopband attenuation

Group delay

65

dB

21/Fs

Sec

STEREO HEADPHONE DRIVER

AC-coupled output configuration⁽³⁾

0-dB gain to high power outputs. Output

common-mode voltage setting = 1.35 V

0-dB full-scale output voltage

0.707

V_RMS

First option

1.35

1.50

1.65

1.8

Programmable output common mode

voltage (applicable to Line Outputs

also)

Second option

Third option

Fourth option

V

Maximum programmable output level

control gain

9

1

dB

Programmable output level control

gain step size

R_L= 32 Ω

R_L= 16 Ω

15

30

P_O

Maximum output power

mW

dB

Signal-to-noise ratio, A-weighted⁽⁴⁾

94

–77

0.014

–76

0.016

–73

0.022

–71

0.028

90

1-kHz output, P_O= 5 mW, R_L= 32 Ω

1-kHz output, P_O= 10 mW, R_L= 32 Ω

1-kHz output, P_O= 10 mW, R_L= 16 Ω

1-kHz output, P_O= 20 mW, R_L= 16 Ω

Total harmonic distortion

dB%

Channel separation

Power supply rejection ratio

Mute attenuation

1 kHz, 0 dB input

dB

217 Hz, 100 mVpp on AVDD, DRVDD1/2

1-kHz output

48

107

(3) Unless otherwise noted, all measurements use output common-mode voltage setting of 1.35 V, 0-dB output level control gain, 16-Ω

single-ended load.

(4) Ratio of output level with a 1-kHz full-scale input, to the output level playing an all-zero signal, measured A-weighted over a 20-Hz to

20-kHz bandwidth.

6

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

ELECTRICAL CHARACTERISTICS (continued)

At 25°C, AVDD, DRVDD, IOVDD = 3.3 V, DVDD = 1.8 V, Fs = 48-kHz, 16-bit audio data (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

DIGITAL I/O

0.3 ×

IOVDD

V_IL

Input low level

Input high level⁽⁵⁾

I_IL= +5-µA

–0.3

V

0.7 ×

IOVDD

V_IH

V_OL

V_OH

I_IH= +5-µA

0.1 ×

IOVDD

Output low level

Output high level

I_IH= 2 TTL loads

I_OH= 2 TTL loads

0.8 ×

IOVDD

SUPPLY CURRENT

Stereo line playback

Fs = 48-kHz

AVDD+DRVDD

DVDD

3.0

2.0

2

Fs = 48-kHz, PLL off, headphone

drivers off

mA

AVDD+DRVDD

DVDD

Mono record

Stereo record

PLL

Fs = 48-kHz, PLL and AGC off

2.7

4

AVDD+DRVDD

DVDD

3.3

1.2

1

AVDD+DRVDD

DVDD

Additional power consumed when

PLL is powered

AVDD+DRVDD LINE2LP/RP only routed to

3.3

Headphone amplifier

Power down

single-ended headphones, DAC and

PLL off, no signal applied

mA

DVDD

0

AVDD+DRVDD

DVDD

0.1

0.5

All supply voltages applied, all blocks

programmed in lowest power state

µA

(5) When IOVDD < 1.6 V, minimum V_IHis 1.1 V.

Submit Documentation Feedback

7

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

AUDIO DATA SERIAL INTERFACE TIMING DIAGRAMS

All specifications at 25°C, DVDD = 1.8 V.

WCLK

t_d(WS)

BCLK

t_d(DO-WS)

t_d(DO-BCLK)

SDOUT

t_S(DI)

t_h(DI)

SDIN

T0145-01

IOVDD = 1.1 V

IOVDD = 3.3 V

PARAMETER

UNIT

MIN

MAX

MIN

MAX

t_d(WS)

ADWS/WCLK delay time

50

15

20

15

ns

t_d(DO-WS)

ADWS/WCLK to DOUT delay time

BCLK to DOUT delay time

DIN setup time

t_d(DO-BCLK)

t_s(DI)

t_h(DI)

t_r

10

6

DIN hold time

Rise time

30

10

t_f

Fall time

NOTE: All timing specifications are measured at characterization but not tested at final test.

Figure 2. I²S/LJF/RJF Timing in Master Mode

8

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

All specifications at 25°C, DVDD = 1.8 V.

WCLK

t_d(WS)

BCLK

SDOUT

SDIN

t_d(DO-BCLK)

t_S(DI)

t_h(DI)

T0146-01

IOVDD = 1.1 V

IOVDD = 3.3 V

PARAMETER

UNIT

MIN

MAX

MIN

MAX

t_d(WS)

ADWS/WCLK delay time

50

15

ns

t_d(DO-BCLK)

BCLK to DOUT delay time

DIN setup time

DIN hold time

Rise time

t_s(DI)

t_h(DI)

t_r

10

6

30

10

t_f

Fall time

NOTE: All timing specifications are measured at characterization but not tested at final test.

Figure 3. DSP Timing in Master Mode

Submit Documentation Feedback

9

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

All specifications at 25°C, DVDD = 1.8 V.

WCLK

t_S(WS)

t_h(WS)

t_H(BCLK)

BCLK

t_L(BCLK)

t_d(DO-WS)

t_d(DO-BCLK)

SDOUT

t_S(DI)

t_h(DI)

SDIN

T0145-02

IOVDD = 1.1 V

IOVDD = 3.3 V

PARAMETER

UNIT

MIN

70

MAX

MIN

35

6

MAX

t_H(BCLK)

t_L(BCLK)

t_s(WS)

t_h(WS)

t_d(DO-WS)

t_d(DO-BCLK)

t_s(DI)

BCLK high period

BCLK low period

ns

70

ADWS/WCLK setup time

ADWS/WCLK hold time

10

6

ADWS/WCLK to DOUT delay time (for LJF Mode only)

50

35

20

BCLK to DOUT delay time

DIN setup time

DIN hold time

Rise time

10

6

t_h(DI)

t_r

8

4

t_f

Fall time

NOTE: All timing specifications are measured at characterization but not tested at final test.

Figure 4. I²S/LJF/RJF Timing in Slave Mode

10

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

All specifications at 25°C, DVDD = 1.8 V.

WCLK

t_S(WS)

t_h(WS)

t_S(WS)

t_h(WS)

t_L(BCLK)

BCLK

t_H(BCLK)

t_d(DO-BCLK)

SDOUT

t_S(DI)

t_h(DI)

SDIN

T0146-02

IOVDD = 1.1 V

IOVDD = 3.3 V

PARAMETER

UNIT

MIN

70

MAX

MIN

35

8

MAX

t_H(BCLK)

t_L(BCLK)

t_s(WS)

BCLK high period

BCLK low period

ns

70

ADWS/WCLK setup time

ADWS/WCLK hold time

10

t_h(WS)

10

8

t_d(DO-BCLK) BCLK to DOUT delay time

50

20

t_s(DI)

t_h(DI)

t_r

DIN setup time

DIN hold time

Rise time

10

6

8

4

t_f

Fall time

NOTE: All timing specifications are measured at characterization but not tested at final test.

Figure 5. DSP Timing in Slave Mode

Submit Documentation Feedback

11

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

TYPICAL CHARACTERISTICS

-20

-30

Capless, VDD = 3.6 V

AC-Coupled,

VDD = 2.7 V

-40

-50

-60

-70

-80

-90

-40

AC-Coupled, VDD = 2.7 V

AC-Coupled, VDD = 3.6 V

Capless,

VDD = 2.7 V

-50

Capless,

VDD = 3.6 V

-60

-70

-80

AC-Coupled,

VDD = 3.6 V

Capless, VDD = 2.7 V

0.015

0.02

0.025

0.03

0.035

0.04

Power - W

-90

0.005

0.00

0.02

0.01

Power - W

Figure 7. Headphone Power vs THD, 32 Ω Load

0.01

0.02

Figure 6. Headphone Power vs THD, 16 Ω Load

0.00

-20.00

-40.00

-60.00

-80.00

-100.00

-120.00

-140.00

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16 17 18 19 20

Frequency - kHz

Figure 8. DAC to Line Output FFT Plot

12

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

TYPICAL CHARACTERISTICS (continued)

0

-20

-40

-60

-80

-100

-120

-140

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16 17 18 19 20

Frequency - kHz

Figure 9. Line Input to ADC FFT Plot

-10.00

-20.00

-30.00

-40.00

-50.00

-60.00

-70.00

-80.00

-90.00

VDD = 2.7 V

VDD = 3.3 V

VDD = 3.6 V

0.10

0.20

0.30

0.40

0.50

0.60

Power - W

Figure 10. Speaker Power vs THD, 8 Ω Load

Submit Documentation Feedback

13

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

TYPICAL CHARACTERISTICS (continued)

3 8

3 6

3 4

3 2

3 0

2 8

2 6

0

1 0

2 0

30

40

5 0

6 0

PGA Gain Setting - dB

Figure 11. ADC SNR vs PGA Gain Setting, –65 dBFS Input

1.20

1.10

1.00

0.90

0.80

0.70

0.60

0.50

0.40

Left ADC

Right ADC

0

10

20

30

40

50

60

PGA Gain Setting - dB

Figure 12. ADC Gain Error vs PGA Gain Setting

14

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

TYPICAL CHARACTERISTICS (continued)

3.5

3.4

3.3

3.2

MICBIAS=AVDD

3.1

3

2.9

2.8

2.7

2.6

MICBIAS=2.5V

2.5

2.4

2.3

2.2

MICBIAS=2.0V

2.1

2

1.9

1.8

2.7

2.8

2.9

3

3.1

3.2

3.3

3.4

3.5

3.6

AVDD - V

Figure 13. MICBIAS Output Voltage vs AVDD

3.2

3

MICBIAS=AVDD

2.8

2.6

2.4

2.2

2

MICBIAS=2.5V

MICBIAS=2.0V

1.8

-45 -35 -25 -15

-5

5

15

25

35

45

55

65

75

85

Temp - C

Figure 14. MICBIAS Output Voltage vs Ambient Temperature

Submit Documentation Feedback

15

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

TYPICAL CHARACTERISTICS (continued)

TYPICAL CIRCUIT CONFIGURATION

IOVDD

DSP

or

Apps Processor

R_p

AVDD

(2.7V-3.6V)

MICBIAS

2 kW

AVDD_DAC

DRVDD

0.1 mF

0.1mF

1mF

MIC1L/LINE1L

0.1mF

1mF

1mF 10mF

0.1mF

A

0.47 mF

IOVDD

(1.1-3.3V)

FM

Tuner

LINE_L

MIC2L/LINE2L

MIC2R/LINE2R

A

0.47 mF

IOVDD

DVDD

0.47 mF

LINE_R

1.65-1.95V

AIC32

MIC3L/LINE3L

MIC3R/LINE3R

1mF

0.1mF

1mF

0.1mF

0.47 mF

DVSS

2 kW

0.1 mF

D

MIC1R/LINE1R

AVSS_DAC

DRVSS

A

LINE_OUT_L-

LINE_OUT_L+

LINE_OUT_R-

LINE_OUT_R+

220 mF

8W

A

Figure 15. Typical Connections for Headphone and Speaker Drive

16

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

TYPICAL CHARACTERISTICS (continued)

IOVDD

DSP

or

Apps Processor

R_p

AVDD

(2.7V-3.6V)

MICBIAS

AVDD_DAC

DRVDD

2 kW

0.1 mF

1 mF

MIC1L/LINE1L

0.1 mF

1mF

0.1 mF

10 mF

A

1mF

0.47 mF

IOVDD

(1.1-3.3V)

MIC2L/LINE2L

MIC2R/LINE2R

FM

Tuner

0.47 mF

IOVDD

DVDD

0.47 mF

1.65-1.95V

AIC32

MIC3L/LINE3L

MIC3R/LINE3R

1 mF

LINE_L

0.1 mF

1mF

LINE_L

0.1 mF

0.47 mF

1 mF

DVSS

2 kW

0.1 mF

D

MIC1R/LINE1R

AVSS_DAC

DRVSS

A

External Audio Power Amplifiers

TPA2012D2 (Stereo Class-D in WCSP)

TPA2010D1 (Mono Class-D in WCSP)

TPA2005D1 (Mono Class-D in BGA, QFN, MSOP)

8 W

Figure 16. Typical Connections for Capless Headphone and External Speaker Amp

Submit Documentation Feedback

17

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

OVERVIEW

The TLV320AIC32 is a highly flexible, low power, stereo audio codec with extensive feature integration, intended

for applications in smartphones, PDAs, and portable computing, communication, and entertainment applications.

Available in a 5 x 5 mm, 32-lead QFN, the product integrates a host of features to reduce cost, board space, and

power consumption in space-constrained, battery-powered, portable applications.

The TLV320AIC32 consists of the following blocks:

•

Stereo audio multi-bit delta-sigma DAC (8 kHz – 96 kHz)

Stereo audio multi-bit delta-sigma ADC (8 kHz – 96 kHz)

Programmable digital audio effects processing (3-D, bass, treble, mid-range, EQ, de-emphasis)

Six audio inputs

Four high-power audio output drivers (headphone/speaker drive capability)

Three fully differential line output drivers

Fully programmable PLL

Headphone/headset jack detection with interrupt

HARDWARE RESET

The TLV320AIC32 requires a hardware reset after power-up for proper operation. After all power supplies are at

their specified values, the RESET pin must be driven low for at least 10 ns. If this reset sequence is not

performed, the 'AIC32 may not respond properly to register reads/writes.

DIGITAL CONTROL SERIAL INTERFACE

The register map of the TLV320AIC32 actually consists of multiple pages of registers, with each page containing

128 registers. The register at address zero on each page is used as a page-control register, and writing to this

register determines the active page for the device. All subsequent read/write operations will access the page that

is active at the time, unless a register write is performed to change the active page. Only two pages of registers

are implemented in this product, with the active page defaulting to page 0 upon device reset.

For example, at device reset, the active page defaults to page 0, and thus all register read/write operations for

addresses 1 to 127 will access registers in page 0. If registers on page 1 must be accessed, the user must write

the 8-bit sequence 0x01 to register 0, the page control register, to change the active page from page 0 to page 1.

After this write, it is recommended the user also read back the page control register, to safely ensure the change

in page control has occurred properly. Future read/write operations to addresses 1 to 127 will now access

registers in page 1. When page 0 registers must be accessed again, the user writes the 8-bit sequence 0x00 to

register 0, the page control register, to change the active page back to page 0. After a recommended read of the

page control register, all further read/write operations to addresses 1 to 127 will now access page 0 registers

again.

I²C CONTROL INTERFACE

The TLV320AIC32 supports the I²C control protocol using 7-bit addressing and is capable of both standard and

fast modes. For I²C fast mode, note that the minimum timing for each of tHD-STA, tSU-STA, and tSU-STO is 2.0

µs, as seen in Figure 17. The TLV320AIC32 will respond to the I²C address of 0011000. I2C is a two-wire,

open-drain interface supporting multiple devices and masters on a single bus. Devices on the I²C bus only drive

the bus lines LOW by connecting them to ground; they never drive the bus lines HIGH. Instead, the bus wires

are pulled HIGH by pull-up resistors, so the bus wires are HIGH when no device is driving them LOW. This way,

two devices cannot conflict; if two devices drive the bus simultaneously, there is no driver contention.

18

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

SDA

t_HD-STA³ 2.0 ms

SCL

t_SU-STA³ 2.0 ms

t_SU-STO³ 2.0 ms

t_HD-STA³ 2.0 ms

S

Sr

P

S

T0114-02

Figure 17. I²C Interface Timing

Communication on the I²C bus always takes place between two devices, one acting as the master and the other

acting as the slave. Both masters and slaves can read and write, but slaves can only do so under the direction of

the master. Some I²C devices can act as masters or slaves, but the TLV320AIC32 can only act as a slave

device.

An I²C bus consists of two lines, SDA and SCL. SDA carries data; SCL provides the clock. All data is transmitted

across the I²C bus in groups of eight bits. To send a bit on the I²C bus, the SDA line is driven to the appropriate

level while SCL is LOW (a LOW on SDA indicates the bit is zero; a HIGH indicates the bit is one). Once the SDA

line has settled, the SCL line is brought HIGH, then LOW. This pulse on SCL clocks the SDA bit into the

receivers shift register.

The I²C bus is bidirectional: the SDA line is used both for transmitting and receiving data. When a master reads

from a slave, the slave drives the data line; when a master sends to a slave, the master drives the data line.

Under normal circumstances the master drives the clock line.

Most of the time the bus is idle, no communication is taking place, and both lines are HIGH. When

communication is taking place, the bus is active. Only master devices can start a communication. They do this by

causing a START condition on the bus. Normally, the data line is only allowed to change state while the clock

line is LOW. If the data line changes state while the clock line is HIGH, it is either a START condition or its

counterpart, a STOP condition. A START condition is when the clock line is HIGH and the data line goes from

HIGH to LOW. A STOP condition is when the clock line is HIGH and the data line goes from LOW to HIGH.

After the master issues a START condition, it sends a byte that indicates which slave device it wants to

communicate with. This byte is called the address byte. Each device on an I²C bus has a unique 7-bit address to

which it responds. (Slaves can also have 10-bit addresses; see the I²C specification for details.) The master

sends an address in the address byte, together with a bit that indicates whether it wishes to read from or write to

the slave device.

Every byte transmitted on the I²C bus, whether it is address or data, is acknowledged with an acknowledge bit.

When a master has finished sending a byte (eight data bits) to a slave, it stops driving SDA and waits for the

slave to acknowledge the byte. The slave acknowledges the byte by pulling SDA LOW. The master then sends a

clock pulse to clock the acknowledge bit. Similarly, when a master has finished reading a byte, it pulls SDA LOW

to acknowledge this to the slave. It then sends a clock pulse to clock the bit.

A not-acknowledge is performed by simply leaving SDA HIGH during an acknowledge cycle. If a device is not

present on the bus, and the master attempts to address it, it will receive a not−acknowledge because no device

is present at that address to pull the line LOW.

When a master has finished communicating with a slave, it may issue a STOP condition. When a STOP

condition is issued, the bus becomes idle again. A master may also issue another START condition. When a

START condition is issued while the bus is active, it is called a repeated START condition.

Submit Documentation Feedback

19

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

The TLV320AIC32 also responds to and acknowledges a General Call, which consists of the master issuing a

command with a slave address byte of 00H.

SCL

DA(6)

DA(0)

RA(7)

RA(0)

D(7)

D(0)

SDA

Slave

Ack

(S)

Slave

Ack

(S)

Slave

Ack

(S)

Start

(M)

7-bit Device Address

(M)

Write

(M)

8-bit Register Address

(M)

8-bit Register Data

(M)

Stop

(M)

(M) => SDA Controlled by Master

(S) => SDA Controlled by Slave

Figure 18. I2C Write

SCL

SDA

DA(6)

DA(0)

D(7)

D(0)

DA(6)

DA(0)

RA(7)

RA(0)

Start

(M)

Master

No Ack

(M)

Stop

(M)

7-bit Device Address

(M)

Write

(M)

Slave

Ack

(S)

8-bit Register Address

(M)

Slave

Ack

(S)

Repeat

Start

(M)

7-bit Device Address

(M)

Read

(M)

Slave

Ack

(S)

8-bit Register Data

(S)

(M) => SDA Controlled by Master

(S) => SDA Controlled by Slave

Figure 19. I2C Read

In the case of an I²C register write, if the master does not issue a STOP condition, then the device enters

auto-increment mode. So in the next eight clocks, the data on SDA is treated as data for the next incremental

register.

Similarly, in the case of an I²C register read, after the device has sent out the 8-bit data from the addressed

register, if the master issues a ACKNOWLEDGE, the slave takes over control of SDA bus and transmit for the

next 8 clocks the data of the next incremental register.

DIGITAL AUDIO DATA SERIAL INTERFACE

Audio data is transferred between the host processor and the TLV320AIC32 via the digital audio data serial

interface, or audio bus. The audio bus of the TLV320AIC32 can be configured for left or right justified, I2S, DSP,

or TDM modes of operation, where communication with standard telephony PCM interfaces is supported within

the TDM mode. These modes are all MSB-first, with data width programmable as 16, 20, 24, or 32 bits. In

addition, the word clock (WCLK) and bit clock (BCLK) can be independently configured in either Master or Slave

mode, for flexible connectivity to a wide variety of processors

The word clock (WCLK) is used to define the beginning of a frame, and may be programmed as either a pulse or

a square-wave signal. The frequency of this clock corresponds to the maximum of the selected ADC and DAC

sampling frequencies.

The bit clock (BCLK) is used to clock in and out the digital audio data across the serial bus. When in Master

mode, this signal can be programmed in two further modes: continuous transfer mode, and 256-clock mode. In

continuous transfer mode, only the minimal number of bit clocks needed to transfer the audio data are generated,

so in general the number of bit clocks per frame will be two times the data width. For example, if data width is

chosen as 16-bits, then 32 bit clocks will be generated per frame. If the bit clock signal in master mode will be

used by a PLL in another device, it is recommended that the 16-bit or 32-bit data width selections be used.

These cases result in a low jitter bit clock signal being generated, having frequencies of 32×Fs or 64×Fs. In the

cases of 20-bit and 24-bt data width in master mode, the bit clocks generated in each frame will not all be of

equal period, due to the device not having a clean 40×Fs or 48×Fs clock signal readily available. The average

frequency of the bit clock signal is still accurate in these cases (being 40×Fs or 48×Fs), but the resulting clock

signal has higher jitter than in the 16-bit and 32-bit cases.

20

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

In 256-clock mode, a constant 256 bit clocks per frame are generated, independent of the data width chosen.

The TLV320AIC32 further includes programmability to tri-state the DOUT line during all bit clocks when valid

data is not being sent. By combining this capability with the ability to program at what bit clock in a frame the

audio data will begin, time-division multiplexing (TDM) can be accomplished, resulting in multiple codecs able to

use a single audio serial data bus.

When the audio serial data bus is powered down while configured in master mode, the pins associated with the

interface will be put into a tri-state output condition.

RIGHT JUSTIFIED MODE

In right-justified mode, the LSB of the left channel is valid on the rising edge of the bit clock preceding the falling

edge of word clock. Similarly, the LSB of the right channel is valid on the rising edge of the bit clock preceding

the rising edge of the word clock.

1/fs

WCLK

BCLK

Left Channel

Right Channel

n−3

SDIN/

SDOUT

n−1 n−2

0

n−3

2

1

0

2

1

0

n−1 n−2

MSB

LSB

Figure 20. Right Justified Serial Bus Mode Operation

LEFT JUSTIFIED MODE

In left-justified mode, the MSB of the right channel is valid on the rising edge of the bit clock following the falling

edge of the word clock. Similarly the MSB of the left channel is valid on the rising edge of the bit clock following

the rising edge of the word clock.

n-1 n-2 n-3

Figure 21. Left Justified Serial Data Bus Mode Operation

I2S MODE

In I2S mode, the MSB of the left channel is valid on the second rising edge of the bit clock after the falling edge

of the word clock. Similarly the MSB of the right channel is valid on the second rising edge of the bit clock after

the rising edge of the word clock.

Submit Documentation Feedback

21

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

n-1 n-2 n-3

Figure 22. I2S Serial Data Bus Mode Operation

DSP MODE

In DSP mode, the rising edge of the word clock starts the data transfer with the left channel data first and

immediately followed by the right channel data. Each data bit is valid on the falling edge of the bit clock.

1/fs

WCLK

BCLK

Right Channel

Left Channel

SDIN/SDOUT

n–1 n–2 n–3 n–4

LSB MSB

2

1

0

n–1 n–2 n–3

2

1

0

n–1

LSB MSB

LSB

T0152-01

Figure 23. DSP Serial Bus Mode Operation

TDM DATA TRANSFER

Time-division multiplexed data transfer can be realized in any of the above transfer modes if the 256-clock bit

clock mode is selected, although it is recommended to be used in either left-justified mode or DSP mode. By

changing the programmable offset, the bit clock in each frame where the data begins can be changed, and the

serial data output driver (DOUT) can also be programmed to tri-state during all bit clocks except when valid data

is being put onto the bus. This allows other codecs to be programmed with different offsets and to drive their

data onto the same DOUT line, just in a different slot. For incoming data, the codec simply ignores data on the

bus except where it is expected based on the programmed offset.

Note that the location of the data when an offset is programmed is different, depending on what transfer mode is

selected. In DSP mode, both left and right channels of data are transferred immediately adjacent to each other in

the frame. This differs from left-justified mode, where the left and right channel data will always be a half-frame

apart in each frame. In this case, as the offset is programmed from zero to some higher value, both the left and

right channel data move across the frame, but still stay a full half-frame apart from each other. This is depicted in

Figure 24 for the two cases.

22

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

DSP Mode

word

clock

bit clock

data

in/out

N-1 N-2

1

0

N-1 N-2

1

0

Right Channel Data

Left Channel Data

offset

Left Justified Mode

word

clock

bit clock

data

in/out

N-1 N-2

1

0

N-1 N-2

1

0

Right Channel Data

Left Channel Data

offset

Figure 24. DSP Mode and Left Justified Modes, Showing the

Effect of a Programmed Data Word Offset

AUDIO DATA CONVERTERS

The TLV320AIC32 supports the following standard audio sampling rates: 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, and 96 kHz. The converters can also operate at

different sampling rates in various combinations, which are described further below.

The data converters are based on the concept of an Fsref rate that is used internal to the part, and it is related to

the actual sampling rates of the converters through a series of ratios. For typical sampling rates, Fsref will be

either 44.1 kHz or 48 kHz, although it can realistically be set over a wider range of rates up to 53 kHz, with

additional restrictions applying if the PLL is used. This concept is used to set the sampling rates of the ADC and

DAC, and also to enable high quality playback of low sampling rate data, without high frequency audible noise

being generated.

The sampling rate of the ADC and DAC can be set to Fsref/NDAC or 2×Fsref/NDAC, with NDAC being 1, 1.5, 2,

2.5, 3, 3.5, 4, 4.5, 5, 5.5, or 6.

AUDIO CLOCK GENERATION

The audio converters in the TLV320AIC32 need an internal audio master clock at a frequency of 256×Fsref,

which can be obtained in a variety of manners from an external clock signal applied to the device.

A more detailed diagram of the audio clock section of the TLV320AIC32 is shown in Figure 25.

Submit Documentation Feedback

23

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

MCLK BCLK

PLL_CLKIN

CLKDIV_CLKIN

CLKDIV_IN

PLL_IN

K = J.D

J = 1,2,3,…..,62,63

D= 0000,0001,….,9998,9999

R= 1,2,3,4,….,15,16

P= 1,2,….,7,8

K*R/P

Q=2,3,…..,16,17

2/Q

CLKDIV_OUT

PLL_OUT

1/8

PLLDIV_OUT

CODEC_CLKIN

CODEC_CLK=256*Fsref

CODEC

DAC_FS

ADC_FS

WCLK= Fsref/Ndac

Ndac=1,1.5,2,…..,5.5,6

DAC DRA => Ndac = 0.5

Figure 25. Audio Clock Generation Processing

The part can accept an MCLK input from 512 kHz to 50 MHz, which can then be passed through either a

programmable divider or a PLL, to get the proper internal audio master clock needed by the part. The BCLK

input can also be used to generate the internal audio master clock.

A primary concern is proper operation of the codec at various sample rates with the limited MCLK frequencies

available in the system. This device includes a highly programmable PLL to accommodate such situations easily.

The integrated PLL can generate audio clocks from a wide variety of possible MCLK inputs, with particular focus

paid to the standard MCLK rates already widely used.

When the PLL is disabled,

Fsref = CLKDIV_IN / (128 × Q)

Where Q = 2, 3, …, 17

CLKDIV_IN can be MCLK or BCLK, selected by register 102, bits D7-D6.

NOTE – when NDAC = 1.5, 2.5, 3.5, 4.5, or 5.5, odd values of Q are not allowed. In this mode, MCLK can be as

high as 50 MHz, and Fsref should fall within 39 kHz to 53 kHz.

24

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

When the PLL is enabled,

Fsref = (PLLCLK_IN × K × R) / (2048 × P), where

P = 1, 2, 3,…, 8

R = 1, 2, …, 16

K = J.D

J = 1, 2, 3, …, 63

D = 0000, 0001, 0002, 0003, …, 9998, 9999

PLLCLK_IN can be MCLK or BCLK, selected by Page 0, register 102, bits D5-D4

P, R, J, and D are register programmable. J is the integer portion of K (the numbers to the left of the decimal

point), while D is the fractional portion of K (the numbers to the right of the decimal point, assuming four digits of

precision).

Examples:

If K = 8.5, then J = 8, D = 5000

If K = 7.12, then J = 7, D = 1200

If K = 14.03, then J = 14, D = 0300

If K = 6.0004, then J = 6, D = 0004

When the PLL is enabled and D = 0000, the following conditions must be satisfied to meet specified

performance:

2 MHz ≤ ( PLLCLK_IN / P ) ≤ 20 MHz

80 MHz ≤ (PLLCLK _IN × K × R / P ) ≤ 110 MHz

4 ≤ J ≤ 55

When the PLL is enabled and D≠0000, the following conditions must be satisfied to meet specified performance:

10 MHz ≤ PLLCLK _IN / P ≤ 20 MHz

80 MHz ≤ PLLCLK _IN × K × R / P ≤ 110 MHz

4 ≤ J ≤ 11

R = 1

Example:

MCLK = 12 MHz and Fsref = 44.1 kHz

Select P = 1, R = 1, K = 7.5264, which results in J = 7, D = 5264

Example:

MCLK = 12 MHz and Fsref = 48.0 kHz

Select P = 1, R = 1, K = 8.192, which results in J = 8, D = 1920

Submit Documentation Feedback

25

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

The table below lists several example cases of typical MCLK rates and how to program the PLL to achieve

Fsref = 44.1 kHz or 48 kHz.

Fsref = 44.1 kHz

MCLK (MHz)

2.8224

5.6448

12.0

P

1

4

R

1

J

32

16

7

D

ACHIEVED FSREF

44100.00

% ERROR

0.0000

0.0007

0.0000

–0.0007

0.0000

0

44100.00

5264

9474

6448

7040

5893

5264

44100.00

13.0

6

44099.71

16.0

5

44100.00

19.2

4

44100.00

19.68

4

44100.30

48.0

7

44100.00

Fsref = 48 kHz

MCLK (MHz)

2.048

P

1

4

R

1

J

48

32

24

16

12

8

D

0

ACHIEVED FSREF

48000.00

47999.71

48000.00

47999.79

48000.00

% ERROR

0.0000

0.0006

0.0000

0.0004

0.0000

3.072

0

4.096

0

6.144

0

8.192

0

12.0

1920

5618

1440

1200

9951

1920

13.0

7

16.0

6

19.2

5

19.68

4

48.0

8

STEREO AUDIO ADC

The TLV320AIC32 includes a stereo audio ADC, which uses a delta-sigma modulator with 128-times

oversampling in single-rate mode, followed by a digital decimation filter. The ADC supports sampling rates from 8

kHz to 48 kHz in single-rate mode, and up to 96 kHz in dual-rate mode. Whenever the ADC or DAC is in

operation, the device requires an audio master clock be provided and appropriate audio clock generation be

setup within the part.

In order to provide optimal system power dissipation, the stereo ADC can be powered one channel at a time, to

support the case where only mono record capability is required. In addition, both channels can be fully powered

or entirely powered down.

The integrated digital decimation filter removes high-frequency content and downsamples the audio data from an

initial sampling rate of 128 Fs to the final output sampling rate of Fs. The decimation filter provides a linear phase

output response with a group delay of 17/Fs. The –3 dB bandwidth of the decimation filter extends to 0.45 Fs

and scales with the sample rate (Fs). The filter has minimum 75dB attenuation over the stopband from 0.55 Fs to

64 Fs. Independent digital highpass filters are also included with each ADC channel, with a corner frequency that

can be independently set to three different settings or can be disabled entirely.

Because of the oversampling nature of the audio ADC and the integrated digital decimation filtering,

requirements for analog anti-aliasing filtering are very relaxed. The TLV320AIC32 integrates a second order

analog anti-aliasing filter with 20-dB attenuation at 1 MHz. This filter, combined with the digital decimation filter,

provides sufficient anti-aliasing filtering without requiring additional external components.

The ADC is preceded by a programmable gain amplifier (PGA), which allows analog gain control from 0 dB to

59.5 dB in steps of 0.5 dB. The PGA gain changes are implemented with an internal soft-stepping algorithm that

only changes the actual volume level by one 0.5-dB step every one or two ADC output samples, depending on

the register programming (see registers Page-0/Reg-19 and 22). This soft-stepping ensures that volume control

changes occur smoothly with no audible artifacts. On reset, the PGA gain defaults to a mute condition, and upon

26

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

power down, the PGA soft-steps the volume to mute before shutting down. A read-only flag is set whenever the

gain applied by PGA equals the desired value set by the register. The soft-stepping control can also be disabled

by programming a register bit. When soft stepping is enabled, the audio master clock must be applied to the part

after the ADC power down register is written to ensure the soft-stepping to mute has completed. When the ADC

powerdown flag is no longer set, the audio master clock can be shut down.

AUTOMATIC GAIN CONTROL (AGC)

An automatic gain control (AGC) circuit is included with the ADC and can be used to maintain nominally constant

output signal amplitude when recording speech signals (it can be fully disabled if not desired). This circuitry

automatically adjusts the PGA gain as the input signal becomes overly loud or very weak, such as when a

person speaking into a microphone moves closer or farther from the microphone. The AGC algorithm has several

programmable settings, including target gain, attack and decay time constants, noise threshold, and maximum

PGA gain applicable that allow the algorithm to be fine tuned for any particular application. The algorithm uses

the absolute average of the signal (which is the average of the absolute value of the signal) as a measure of the

nominal amplitude of the output signal.

Note that completely independent AGC circuitry is included with each ADC channel with entirely independent

control over the algorithm from one channel to the next. This is attractive in cases where two microphones are

used in a system, but may have different placement in the end equipment and require different dynamic

performance for optimal system operation.

Target gain represents the nominal output level at which the AGC attempts to hold the ADC output signal level.

The TLV320AIC32 allows programming of eight different target gains, which can be programmed from –5.5 dB to

–24 dB relative to a full-scale signal. Since the device reacts to the signal absolute average and not to peak

levels, it is recommended that the larger gain be set with enough margin to avoid clipping at the occurrence of

loud sounds.

Attack time determines how quickly the AGC circuitry reduces the PGA gain when the input signal is too loud. It

can be varied from 8 ms to 20 ms.

Decay time determines how quickly the PGA gain is increased when the input signal is too low. It can be varied

in the range from 100 ms to 500 ms.

Noise gate threshold determines the level below which if the input speech average value falls, AGC considers it

as a silence and hence brings down the gain to 0 dB in steps of 0.5 dB every FS and sets the noise threshold

flag. The gain stays at 0 dB unless the input speech signal average rises above the noise threshold setting. This

ensures that noise does not get gained up in the absence of speech. Noise threshold level in the AGC algorithm

is programmable from –30 dB to –90 dB relative to full scale. A disable noise gate feature is also available. This

operation includes programmable debounce and hysteresis functionality to avoid the AGC gain from cycling

between high gain and 0 dB when signals are near the noise threshold level. When the noise threshold flag is

set, the status of gain applied by the AGC and the saturation flag should be ignored.

Maximum PGA gain applicable allows the user to restrict the maximum PGA gain that can be applied by the

AGC algorithm. This can be used for limiting PGA gain in situations where environmental noise is greater than

programmed noise threshold. It can be programmed from 0 dB to +59.5 dB in steps of 0.5 dB.

Submit Documentation Feedback

27

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Input

Signal

Output

Signal

AGC

Gain

Attack

Decay Time

Time

Figure 26. Typical Operation of the AGC Algorithm During Speech Recording

Note that the time constants here are correct when the ADC is not in double-rate audio mode. The time

constants are achieved using the Fsref value programmed in the control registers. However, if the Fsref is set in

the registers to, for example, 48 kHz, but the actual audio clock or PLL programming actually results in a different

Fsref in practice, then the time constants would not be correct.

STEREO AUDIO DAC

The TLV320AIC32 includes a stereo audio DAC supporting sampling rates from 8 kHz to 96 kHz. Each channel

of the stereo audio DAC consists of a digital audio processing block, a digital interpolation filter, multi-bit digital

delta-sigma modulator, and an analog reconstruction filter. The DAC is designed to provide enhanced

performance at low sampling rates through increased oversampling and image filtering, thereby keeping

quantization noise generated within the delta-sigma modulator and signal images strongly suppressed within the

audio band to beyond 20 kHz. This is realized by keeping the upsampled rate constant at 128 × Fsref and

changing the oversampling ratio as the input sample rate is changed. For an Fsref of 48 kHz, the digital

delta-sigma modulator always operates at a rate of 6.144 MHz. This ensures that quantization noise generated

within the delta-sigma modulator stays low within the frequency band below 20 kHz at all sample rates. Similarly,

for an Fsref rate of 44.1 kHz, the digital delta-sigma modulator always operates at a rate of 5.6448 MHz.

The following restrictions apply in the case when the PLL is powered down and double-rate audio mode is

enabled in the DAC.

Allowed Q values = 4, 8, 9, 12, 16

Q values where equivalent Fsref can be achieved by turning on PLL

Q = 5, 6, 7 (set P = 5 / 6 / 7 and K = 16.0 and PLL enabled)

Q = 10, 14 (set P = 5, 7 and K = 8.0 and PLL enabled)

DIGITAL AUDIO PROCESSING

The DAC channel consists of optional filters for de-emphasis and bass, treble, midrange level adjustment,

speaker equalization, and 3-D effects processing. The de-emphasis function is implemented by a programmable

digital filter block with fully programmable coefficients (see Page-1/Reg-21-26 for left channel, Page-1/Reg-47-52

for right channel). If de-emphasis is not required in a particular application, this programmable filter block can be

used for some other purpose. The de-emphasis filter transfer function is given by:

28

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

*1

N0 ) N1 z

H(z) +

*1

32768 * D1 z

(1)

where the N0, N1, and D1 coefficients are fully programmable individually for each channel. The coefficients that

should be loaded to implement standard de-emphasis filters are given in Table 2.

Table 2. De-Emphasis Coefficients for Common Audio Sampling Rates

SAMPLING FREQUENCY

32-kHz

N0

N1

D1

16950

15091

14677

–1220

–2877

–3283

17037

20555

21374

44.1-kHz

48-kHz⁽¹⁾

(1) Default De-emphasis Coeffiicients

In addition to the de-emphasis filter block, the DAC digital effects processing includes a fourth order digital IIR

filter with programmable coefficients (one set per channel). This filter is implemented as cascade of two biquad

sections with frequency response given by:

N0 ) 2 N1 z^*1) N2 z^*2

N3 ) 2 N4 z^*1) N5 z^*2

ǒ

Ǔǒ

Ǔ

32768

*

2

D1

z^*1

*

D2

z^*232768

*

2

D4

z^*1

*

D5

z^*2

(2)

The N and D coefficients are fully programmable, and the entire filter can be enabled or bypassed. The structure

of the filtering when configured for independent channel processing is shown below in Figure 27, with LB1

corresponding to the first left-channel biquad filter using coefficients N0, N1, N2, D1, and D2. LB2 similarly

corresponds to the second left-channel biquad filter using coefficients N3, N4, N5, D4, and D5. The RB1 and

RB2 filters refer to the first and second right-channel biquad filters, respectively.

LB1

LB2

RB1

RB2

Figure 27. Structure of the Digital Effects Processing for Independent Channel Processing

The coefficients for this filter implement a variety of sound effects, with bass-boost or treble boost being the most

commonly used in portable audio applications. The default N and D coefficients in the part are given in Table 3

and implement a shelving filter with 0-dB gain from DC to approximately 150 Hz, at which point it rolls off to a

3-dB attenuation for higher frequency signals, thus giving a 3-dB boost to signals below 150 Hz. The N and D

coefficients are represented by 16-bit two’s complement numbers with values ranging from –32768 to 32767.

Submit Documentation Feedback

29

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Table 3. Default Digital Effects Processing Filter Coefficients,

When in Independent Channel Processing Configuration

Coefficients

N0 = N3

N1 = N4

N2 = N5

D1 = D4

D2=D5

27619

-27034

26461

32131

-31506

The digital processing also includes capability to implement 3-D processing algorithms by providing means to

process the mono mix of the stereo input, and then combine this with the individual channel signals for stereo

output playback. The architecture of this processing mode, and the programmable filters available for use in the

system, is shown in Figure 28. Note that the programmable attenuation block provides a method of adjusting the

level of 3-D effect introduced into the final stereo output. This combined with the fully programmable biquad filters

in the system enables the user to fully optimize the audio effects for a particular system and provide extensive

differentiation from other systems using the same device.

L

LB2

RB2

TOLEFTCHANNEL

TO RIGHT CHANNEL

LB1

Atten

R

Figure 28. Architecture of the Digital Audio Processing When 3-D Effects are Enabled

It is recommended that the digital effects filters should be disabled while the filter coefficients are being modified.

While new coefficients are being written to the device over the control port, it is possible that a filter using

partially updated coefficients may actually implement an unstable system and lead to oscillation or objectionable

audio output. By disabling the filters, changing the coefficients, and then re-enabling the filters, these types of

effects can be entirely avoided.

DIGITAL INTERPOLATION FILTER

The digital interpolation filter upsamples the output of the digital audio processing block by the required

oversampling ratio before data is provided to the digital delta-sigma modulator and analog reconstruction filter

stages. The filter provides a linear phase output with a group delay of 21/Fs. In addition, programmable digital

interpolation filtering is included to provide enhanced image filtering and reduce signal images caused by the

upsampling process that are below 20 kHz. For example, upsampling an 8-kHz signal produces signal images at

multiples of 8-kHz (i.e., 8 kHz, 16 kHz, 24 kHz, etc.). The images at 8 kHz and 16 kHz are below 20 kHz and still

audible to the listener; therefore, they must be filtered heavily to maintain a good quality output. The interpolation

filter is designed to maintain at least 65-dB rejection of images that land below 7.455 Fs. In order to utilize the

programmable interpolation capability, the Fsref should be programmed to a higher rate (restricted to be in the

range of 39 kHz to 53 kHz when the PLL is in use), and the actual Fs is set using the NDAC divider. For

example, if Fs = 8 kHz is required, then Fsref can be set to 48 kHz, and the DAC Fs set to Fsref/6. This ensures

that all images of the 8-kHz data are sufficiently attenuated well beyond a 20-kHz audible frequency range.

30

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

DELTA-SIGMA AUDIO DAC

The stereo audio DAC incorporates a third order multi-bit delta-sigma modulator followed by an analog

reconstruction filter. The DAC provides high-resolution, low-noise performance, using oversampling and noise

shaping techniques. The analog reconstruction filter design consists of a 6-tap analog FIR filter followed by a

continuous time RC filter. The analog FIR operates at a rate of 128 × Fsref (6.144 MHz when Fsref = 48 kHz,

5.6448 MHz when Fsref = 44.1 kHz). Note that the DAC analog performance may be degraded by excessive

clock jitter on the MCLK input. Therefore, care must be taken to keep jitter on this clock to a minimum.

AUDIO DAC DIGITAL VOLUME CONTROL

The audio DAC includes a digital volume control block which implements a programmable digital gain. The

volume level can be varied from 0 dB to –63.5 dB in 0.5-dB steps, in addition to a mute bit, independently for

each channel. The volume level of both channels can also be changed simultaneously by the master volume

control. Gain changes are implemented with a soft-stepping algorithm, which only changes the actual volume by

one step per input sample, either up or down, until the desired volume is reached. The rate of soft-stepping can

be slowed to one step per two input samples through a register bit.

Because of soft-stepping, the host does not know when the DAC has been actually muted. This may be

important if the host wishes to mute the DAC before making a significant change, such as changing sample

rates. In order to help with this situation, the device provides a flag back to the host via a read-only register bit

that alerts the host when the part has completed the soft-stepping and the actual volume has reached the

desired volume level. The soft-stepping feature can be disabled through register programming. If soft-stepping is

enabled, the MCLK signal should be kept applied to the device until the DAC power-down flag is set. When this

flag is set, the internal soft-stepping process and power down sequence is complete, and the MCLK can then be

stopped if desired.

The TLV320AIC32 also includes functionality to detect when the user switches on or off the de-emphasis or

digital audio processing functions, to first (1) soft-mute the DAC volume control, (2) change the operation of the

digital effects processing, and (3) soft-unmute the part. This avoids any possible pop/clicks in the audio output

due to instantaneous changes in the filtering. A similar algorithm is used when first powering up or down the

DAC. The circuit begins operation at power up with the volume control muted, then soft-steps it up to the desired

volume level. At power down, the logic first soft-steps the volume down to a mute level, then powers down the

circuitry.

ANALOG OUTPUT COMMON-MODE ADJUSTMENT

The output common-mode voltage and output range of the analog output are determined by an internal bandgap

reference, in contrast to other codecs that may use a divided version of the supply. This scheme is used to

reduce the coupling of noise that may be on the supply (such as 217-Hz noise in a GSM cellphone) into the

audio signal path.

However, due to the possible wide variation in analog supply range (2.7 V – 3.6 V), an output common-mode

voltage setting of 1.35 V, which would be used for a 2.7 V supply case, will be overly conservative if the supply is

actually much larger, such as 3.3 V or 3.6 V. In order to optimize device operation, the TLV320AIC32 includes a

programmable output common-mode level, which can be set by register programming to a level most appropriate

to the actual supply range used by a particular customer. The output common-mode level can be varied among

four different values, ranging from 1.35 V (most appropriate for low supply ranges, near 2.7 V) to 1.8 V (most

appropriate for high supply ranges, near 3.6 V). Note that there is also some limitation on the range of DVDD

voltage as well in determining which setting is most appropriate.

Table 4. Appropriate Settings

CM SETTING

1.35

RECOMMENDED AVDD, DRVDD

2.7 V – 3.6 V

RECOMMENDED DVDD

1.65 V – 1.95 V

1.8 V – 1.95 V

1.95 V

1.50

3.0 V – 3.6 V

1.65 V

1.8 V

3.3 V – 3.6 V

3.6 V

Submit Documentation Feedback

31

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

AUDIO DAC POWER CONTROL

The stereo DAC can be fully powered up or down, and in addition, the analog circuitry in each DAC channel can

be powered up or down independently. This provides power savings when only a mono playback stream is

needed.

AUDIO ANALOG INPUTS

The TLV320AIC3105 includes six single-ended audio inputs. These pins connect through series resistors and

switches to the virtual ground terminals of two fully differential opamps (one per ADC/PGA channel). By selecting

to turn on only one set of switches per opamp at a time, the inputs can be effectively muxed to each ADC PGA

channel.

By selecting to turn on multiple sets of switches per opamp at a time, mixing can also be achieved. Mixing of

multiple inputs can easily lead to PGA outputs that exceed the range of the internal opamps, resulting in

saturation and clipping of the mixed output signal. Whenever mixing is being implemented, the user should take

adequate precautions to avoid such a saturation case from occurring. In general, the mixed signal should not

exceed 2 Vp-p (single-ended).

In most mixing applications, there is also a general need to adjust the levels of the individual signals being

mixed. For example, if a soft signal and a large signal are to be mixed and played together, the soft signal

generally should be amplified to a level comparable to the large signal before mixing. In order to accommodate

this need, the TLV320AIC3105 includes input level control on each of the individual inputs before they are mixed

or muxed into the ADC PGAs, with gain programmable from 0 dB to –12 dB in 1.5 dB steps. Note that this input

level control is not intended to be a volume control, but instead used occasionally for level setting. Soft-stepping

of the input level control settings is implemented in this device, with the speed and functionality following the

settings used by the ADC PGA for soft-stepping.

Figure 29 shows the single-ended mixing configuration for the left channel ADC PGA, which enables mixing of

the signals LINE1L, LINE2L, LINE1R, MIC3L, and MIC3R. The right channel ADC PGA mix is similar, enabling

mixing of the signals LINE1R, LINE2R, LINE1L, MIC3L, and MIC3R.

GAIN = 0, –1.5, –3, ... –12 dB, MUTE

LINE1L/MIC1L

GAIN = 0, –1.5, –3, ... –12 dB, MUTE

LINE2L/MIC2L

GAIN = 0, –1.5, –3, ... –12 dB, MUTE

TO LEFT ADC

PGA

LINE1R/MIC1R

LINE3L/MIC3L

LINE3R/MIC3R

GAIN = 0, –1.5, –3, ... –12 dB, MUTE

Figure 29. Left Channel Single-Ended Analog Input Mixing Configuration

32

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

ANALOG INPUT BYPASS PATH FUNCTIONALITY

The TLV320AIC3105 includes the additional ability to route some analog input signals past the integrated data

converters, for mixing with other analog signals and then direction connection to the output drivers. This

capability is useful in a cellphone, for example, when a separate FM radio device provides a stereo analog output

signal that needs to be routed to headphones. The TLV320AIC3105 supports this in a low power mode by

providing a direct analog path through the device to the output drivers, while all ADCs and DACs can be

completely powered down to save power. When programmed correctly, the device can pass the signal LINE2L

and LINE2R to the output stage directly.

ADC PGA SIGNAL BYPASS PATH FUNCTIONALITY

In addition to the input bypass path described above, the TLV320AIC32 also includes the ability to route the ADC

PGA output signals past the ADC, for mixing with other analog signals and then direction connection to the

output drivers. These bypass functions are described in more detail in the sections on output mixing and output

driver configurations.

INPUT IMPEDANCE AND VCM CONTROL

The TLV320AIC32 includes several programmable settings to control analog input pins, particularly when they

are not selected for connection to an ADC PGA. The default option allows unselected inputs to be put into a

tri-state condition, such that the input impedance seen looking into the device is extremely high. Note, however,

that the pins on the device do include protection diode circuits connected to AVDD and AVSS. Thus, if any

voltage is driven onto a pin approximately one diode drop (~0.6 V) above AVDD or one diode drop below AVSS,

these protection diodes will begin conducting current, resulting in an effective impedance that no longer appears

as a tri-state condition.

Another programmable option for unselected analog inputs is to weakly hold them at the common-mode input

voltage of the ADC PGA (which is determined by an internal bandgap voltage reference). This is useful to keep

the ac-coupling capacitors connected to analog inputs biased up at a normal DC level, thus avoiding the need for

them to charge up suddenly when the input is changed from being unselected to selected for connection to an

ADC PGA. This option is controlled in Page-0/Reg-20 and 23. The user should ensure this option is disabled

when an input is selected for connection to an ADC PGA or selected for the analog input bypass path, since it

can corrupt the recorded input signal if left operational when an input is selected.

In most cases, the analog input pins on the TLV320AIC32 should be ac-coupled to analog input sources, the

only exception to this generally being if an ADC is being used for DC voltage measurement. The ac-coupling

capacitor will cause a highpass filter pole to be inserted into the analog signal path, so the size of the capacitor

must be chosen to move that filter pole sufficiently low in frequency to cause minimal effect on the processed

analog signal. The input impedance of the analog inputs when selected for connection to an ADC PGA varies

with the setting of the input level control, starting at approximately 20 kΩ with an input level control setting of

0-dB, and increasing to approximately 80-kΩ when the input level control is set at –12 dB. For example, using a

0.1 µF ac-coupling capacitor at an analog input will result in a highpass filter pole of 80 Hz when the 0 dB input

level control setting is selected.

PASSIVE ANALOG BYPASS DURING POWER DOWN

Programming the TLV320AIC3105 to passive analog bypass occurs by configuring the output stage switches for

passthrough. This is done by opening switches SW-L0, SW-R0 and closing either SW-L1 or SW-L2 and SW-R1

or SW-R2. See Figure 30. Programming this mode is done by writing to page 0, register 108.

Connecting the MIC1L/LINE1L input signal to LEFT_LOP is done by closing SW-L1 and opening SW-L0; this

action is done by writing a 1 to page 0, register 108, bit D0. Connecting the MIC2L/LINE2L input signal to

LEFT_LOP is done by closing SW-L2 and opening SW-L0; this action is done by writing a 1 to page 0, register

108, bit D2.

Connecting the MIC1R/LINE1R input signal to RIGHT_LOP is done by closing SW-R1 and opening SW-R0; this

action is done by writing a 1 to page 0, register 108, bit D4. Connecting the MIC2R/LINE2R input signal to

RIGHT_LOP is done by closing SW-R2 and opening SW-R0; this action is done by writing a 1 to page 0, register

108, bit D6. A diagram of the passive analog bypass mode configuration can be seen in Figure 30.

Submit Documentation Feedback

33

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

In general, connecting two switches to the same output pin should be avoided, as this error shorts two input

signals together, which would likely cause distortion of the signal as the two signal are in contention. Poor

frequency response would also likely occur.

LINE2L

SW-L2

LINE2L

MIC2L / LINE2L

SW-L1

LINE1L

SW-L0

LEFT_LOP

LINE1L

LEFT_LOM

MIC1L / LINE1L

LINE1R

SW-R2

SW-R1

SW-R0

LINE2R

LINE1R

MIC1R / LINE1R

RIGHT_LOP

RIGHT_LOM

LINE2R

MIC2R / LINE2R

Figure 30. Passive Analog Bypass Mode Configuration

MICBIAS GENERATION

The TLV320AIC32 includes a programmable microphone bias output voltage (MICBIAS), capable of providing

output voltages of 2.0 V or 2.5 V (both derived from the on-chip bandgap voltage) with 4-mA output current drive.

In addition, the MICBIAS may be programmed to be switched to AVDD directly through an on-chip switch, or it

can be powered down completely when not needed, for power savings. This function is controlled by register

programming in Page-0/Reg-25.

34

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

ANALOG FULLY DIFFERENTIAL LINE OUTPUT DRIVERS

The TLV320AIC32 has two fully differential line output drivers, each capable of driving a 10-kΩ differential load.

The output stage design leading to the fully differential line output drivers is shown in Figure 31 and Figure 32.

This design includes extensive capability to adjust signal levels independently before any mixing occurs, beyond

that already provided by the PGA gain and the DAC digital volume control.

The LINE2L/R signals refer to the signals that travel through the analog input bypass path to the output stage.

The PGA_L/R signals refer to the outputs of the ADC PGA stages that are similarly passed around the ADC to

the output stage. Note that since both left and right channel signals are routed to all output drivers, a mono mix

of any of the stereo signals can easily be obtained by setting the volume controls of both left and right channel

signals to –6 dB and mixing them. Undesired signals can also be disconnected from the mix as well through

register control.

DAC_L1

DAC_L

DAC_L2

STEREO

AUDIO

DAC

DAC_L3

DAC_R1

DAC_R2

DAC_R3

DAC_R

LINE2L

LINE2R

PGA_L

VOLUME

CONTROLS,

MIXING

LEFT_LOP

LEFT_LOM

PGA_R

DAC_L1

DAC_R1

Gain = 0dB to +9dB,

Mute

DAC_L3

LINE2L

LINE2R

PGA_L

VOLUME

CONTROLS,

MIXING

RIGHT_LOP

RIGHT_LOM

PGA_R

DAC_L1

DAC_R1

Gain = 0dB to +9dB,

Mute

DAC_R3

Figure 31. Architecture of the Output Stage Leading to the Fully Differential Line Output Drivers

Submit Documentation Feedback

35

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

0dB to -78dB

LINE2L/MIC2L

LINE2R/MIC2R

PGA_L

+

PGA_R

DAC_L1

DAC_R1

Figure 32. Detail of the Volume Control and Mixing Function Shown in Figure 25 and Figure 16

The DAC_L/R signals are the outputs of the stereo audio DAC, which can be steered by register control based

on the requirements of the system. If mixing of the DAC audio with other signals is not required, and the DAC

output is only needed at the stereo line outputs, then it is recommended to use the routing through path

DAC_L3/R3 to the fully differential stereo line outputs. This results not only in higher quality output performance,

but also in lower power operation, since the analog volume controls and mixing blocks ahead of these drivers

can be powered down. This signal path will attenuate the signal by a factor of 1 dB.

If instead the DAC analog output must be routed to multiple output drivers simultaneously (such as to

LEFT_LOP/M and RIGHT_LOP/M) or must be mixed with other analog signals, then the DAC outputs should be

switched through the DAC_L1/R1 path. This option provides the maximum flexibility for routing of the DAC

analog signals to the output drivers

The TLV320AIC32 includes an output level control on each output driver with limited gain adjustment from 0 dB

to 9 dB. The output driver circuitry in this device are designed to provide a low distortion output while playing

fullscale stereo DAC signals at a 0dB gain setting. However, a higher amplitude output can be obtained at the

cost of increased signal distortion at the output. This output level control allows the user to make this tradeoff

based on the requirements of the end equipment. Note that this output level control is not intended to be used as

a standard output volume control. It is expected to be used only sparingly for level setting, i.e., adjustment of the

fullscale output range of the device.

Each differential line output driver can be powered down independently of the others when it is not needed in the

system. When placed into powerdown through register programming, the driver output pins will be placed into a

tri-stated, high-impedance state.

ANALOG HIGH POWER OUTPUT DRIVERS

The TLV320AIC32 includes four high power output drivers with extensive flexibility in their usage. These output

drivers are individually capable of driving 30 mW each into a 16-Ω load in single-ended configuration, and they

can be used in pairs to drive up to 500 mW into an 8-Ω load connected in bridge-terminated load (BTL)

configuration between two driver outputs.

The high power output drivers can be configured in a variety of ways, including:

1. driving up to two fully differential output signals

2. driving up to four single-ended output signals

3. driving two single-ended output signals, with one or two of the remaining drivers driving a fixed VCM level,

for a pseudo-differential stereo output

4. driving one or two 8-Ω speakers connected BTL between pairs of driver output pins

36

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

5. driving stereo headphones in single-ended configuration with two drivers, while the remaining two drivers are

connected in BTL configuration to an 8-Ω speaker.

The output stage architecture leading to the high power output drivers is shown in Figure 33, with the volume

control and mixing blocks being effectively identical to that shown in Figure 32. Note that each of these drivers

have a output level control block like those included with the line output drivers, allowing gain adjustment up to

+9dB on the output signal. As in the previous case, this output level adjustment is not intended to be used as a

standard volume control, but instead is included for additional fullscale output signal level control.

Two of the output drivers, HPROUT and HPLOUT, include a direct connection path for the stereo DAC outputs to

be passed directly to the output drivers and bypass the analog volume controls and mixing networks, using the

DAC_L2/R2 path. As in the line output case, this functionality provides the highest quality DAC playback

performance with reduced power dissipation, but can only be utilized if the DAC output does not need to route to

multiple output drivers simultaneously, and if mixing of the DAC output with other analog signals is not needed.

The direct connection path will attenuate the signal by a factor of 1 dB.

LINE2L

LINE2R

PGA_L

PGA_R

DAC_L1

DAC_R1

VOLUME

CONTROLS,

MIXING

Volume 0dB to

+9dB, mute

HPLOUT

DAC_L2

LINE2L

LINE2R

PGA_L

PGA_R

Volume 0dB to

+9dB, mute

VOLUME

CONTROLS,

MIXING

HPLCOM

VCM

DAC_L1

DAC_R1

LINE2L

LINE2R

PGA_L

PGA_R

VOLUME

CONTROLS,

MIXING

Volume 0dB

to +9dB,

mute

VCM

DAC_L1

DAC_R1

HPRCOM

DAC_R2

LINE2L

LINE2R

PGA_L

PGA_R

VOLUME

CONTROLS,

MIXING

Volume 0dB to

+9dB, mute

HPROUT

DAC_L1

DAC_R1

Figure 33. Architecture of the output stage leading to the high power output drivers

Submit Documentation Feedback

37

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

The high power output drivers include additional circuitry to avoid artifacts on the audio output during power-on

and power-off transient conditions. The user should first program the type of output configuration being used in

Page-0/Reg-14, to allow the device to select the optimal power-up scheme to avoid output artifacts. The

power-up delay time for the high power output drivers is also programmable over a wide range of time delays,

from instantaneous up to 4-sec, using Page-0/Reg-42.

When these output drivers are powered down, they can be placed into a variety of output conditions based on

register programming. If lowest power operation is desired, then the outputs can be placed into a tri-state

condition, and all power to the output stage is removed. However, this generally results in the output nodes

drifting to rest near the upper or lower analog supply, due to small leakage currents at the pins. This then results

in a longer delay requirement to avoid output artifacts during driver power-on. In order to reduce this required

power-on delay, the TLV320AIC32 includes an option for the output pins of the drivers to be weakly driven to the

VCM level they would normally rest at when powered with no signal applied. This output VCM level is determined

by an internal bandgap voltage reference, and thus results in extra power dissipation when the drivers are in

powerdown. However, this option provides the fastest method for transitioning the drivers from powerdown to full

power operation without any output artifact introduced.

The device includes a further option that falls between the other two – while it requires less power drawn while

the output drivers are in powerdown, it also takes a slightly longer delay to power-up without artifact than if the

bandgap reference is kept alive. In this alternate mode, the powered-down output driver pin is weakly driven to a

voltage of approximately half the DRVDD1/2 supply level using an internal voltage divider. This voltage will not

match the actual VCM of a fully powered driver, but due to the output voltage being close to its final value, a

much shorter power-up delay time setting can be used and still avoid any audible output artifacts. These output

voltage options are controlled in Page-0/Reg-42.

The high power output drivers can also be programmed to power up first with the output level control in a highly

attenuated state, then the output driver will automatically slowly reduce the output attenuation to reach the

desired output level setting programmed. This capability is enabled by default and can be controlled by

Page-0/Reg-40.

SHORT CIRCUIT OUTPUT PROTECTION

The TLV320AIC32 includes programmable short-circuit protection for the high power output drivers, for maximum

flexibility in a given application. By default, if these output drivers are shorted, they will automatically limit the

maximum amount of current that can be sourced to or sunk from a load, thereby protecting the device from an

over-current condition. In this mode, the user can read Page-0/Reg-95 to determine whether the part is in

short-circuit protection or not, and then decide whether to program the device to power down the output drivers.

However, the device includes further capability to automatically power down an output driver whenever it does

into short-circuit protection, without requiring intervention from the user. In this case, the output driver will stay in

a power down condition until the user specifically programs it to power down and then power back up again, to

clear the short-circuit flag.

CONTROL REGISTERS

The control registers for the TLV320AIC32 are described in detail below. All registers are 8 bit in width, with D7

referring to the most significant bit of each register, and D0 referring to the least significant bit.

Page 0 / Register 0:

Page Select Register

BIT⁽¹⁾

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D1

D0

X

0000000 Reserved, write only zeros to these register bits

R/W

0

Page Select Bit

Writing zero to this bit sets Page-0 as the active page for following register accesses. Writing a

one to this bit sets Page-1 as the active page for following register accesses. It is recommended

that the user read this register bit back after each write, to ensure that the proper page is being

accessed for future register read/writes.

(1) When resetting registers related to routing and volume controls of output drivers, it is recommended to reset them by writing directly to

the registers instead of using software reset.

38

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 1:

Software Reset Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

W

0

Software Reset Bit

0 : Don’t Care

1 : Self clearing software reset

D6–D0

W

0000000 Reserved; don’t write

Page 0 / Register 2:

Codec Sample Rate Select Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

ADC Sample Rate Select

0000: ADC Fs = Fsref/1

0001: ADC Fs = Fsref/1.5

0010: ADC Fs = Fsref/2

0011: ADC Fs = Fsref/2.5

0100: ADC Fs = Fsref/3

0101: ADC Fs = Fsref/3.5

0110: ADC Fs = Fsref/4

0111: ADC Fs = Fsref/4.5

1000: ADC Fs = Fsref/5

1001: ADC Fs = Fsref/5.5

1010: ADC Fs = Fsref / 6

1011–1111: Reserved, do not write these sequences.

Note: ADC sample rate must be programmed to same value as DAC sample rate

D3-D0

R/W

0000

DAC Sample Rate Select

0000 : DAC Fs = Fsref/1

0001 : DAC Fs = Fsref/1.5

0010 : DAC Fs = Fsref/2

0011 : DAC Fs = Fsref/2.5

0100 : DAC Fs = Fsref/3

0101 : DAC Fs = Fsref/3.5

0110 : DAC Fs = Fsref/4

0111 : DAC Fs = Fsref/4.5

1000 : DAC Fs = Fsref/5

1001: DAC Fs = Fsref/5.5

1010: DAC Fs = Fsref / 6

1011–1111 : Reserved, do not write these sequences.

Page 0 / Register 3:

PLL Programming Register A

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PLL Control Bit

0: PLL is disabled

1: PLL is enabled

D6–D3

R/W

0010

PLL Q Value

0000: Q = 16

0001 : Q = 17

0010 : Q = 2

0011 : Q = 3

0100 : Q = 4

…

1110: Q = 14

1111: Q = 15

D2–D0

R/W

000

PLL P Value

000: P = 8

001: P = 1

010: P = 2

011: P = 3

100: P = 4

101: P = 5

110: P = 6

111: P = 7

Submit Documentation Feedback

39

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 4:

PLL Programming Register B

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D2

R/W

000001

PLL J Value

000000: Reserved, do not write this sequence

000001: J = 1

000010: J = 2

000011: J = 3

…

111110: J = 62

111111: J = 63

D1–D0

00

Reserved, write only zeros to these bits

Page 0 / Register 5:

PLL Programming Register C

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

00000000 PLL D value – Eight most significant bits of a 14-bit unsigned integer valid values for D are from

zero to 9999, represented by a 14-bit integer located in Page-0/Reg-5-6. Values should not be

written into these registers that would result in a D value outside the valid range.

Page 0 / Register 6:

PLL Programming Register D

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D2

R/W

000000

PLL D value – Six least significant bits of a 14-bit unsigned integer valid values for D are from

zero to 9999, represented by a 14-bit integer located in Page-0/Reg-5-6. Values should not be

written into these registers that would result in a D value outside the valid range.

D1-D0

R

00

Reserved, write only zeros to these bits.

Page 0 / Register 7:

Codec Datapath Setup Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Fsref setting

This register setting controls timers related to the AGC time constants.

0: Fsref = 48-kHz

1: Fsref = 44.1-kHz

D6

R/W

0

ADC Dual rate control

0: ADC dual rate mode is disabled

1: ADC dual rate mode is enabled

Note: ADC Dual Rate Mode must match DAC Dual Rate Mode

D5

R/W

0

DAC Dual Rate Control 0: DAC dual rate mode is disabled 1: DAC dual rate mode is enabled

D4–D3

00

Left DAC Datapath Control

00: Left DAC datapath is off (muted)

01: Left DAC datapath plays left channel input data

10: Left DAC datapath plays right channel input data

11: Left DAC datapath plays mono mix of left and right channel input data

D2–D1

D0

R/W

00

0

Right DAC Datapath Control

00: Right DAC datapath is off (muted)

01: Right DAC datapath plays right channel input data

10: Right DAC datapath plays left channel input data

11: Right DAC datapath plays mono mix of left and right channel input data

Reserved. Only write zero to this register.

40

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 8:

Audio Serial Data Interface Control Register A

BIT

READ/ RESET

WRITE VALUE

DESCRIPTION

D7

R/W

0

Bit Clock Directional Control

0: Bit clock is an input (slave mode)

1: Bit clock is an output (master mode)

D6

D5

D4

Word Clock Directional Control

0: Word clock is an input (slave mode)

1: Word clock is an output (master mode)

Serial Output Data Driver (DOUT) 3-state control

0: Do not 3-state DOUT when valid data is not being sent

1: 3-state DOUT when valid data is not being sent

Bit/ Word Clock Drive Control

0:

1:

Bit clock and word clock will not be transmitted when in master mode if codec is powered down

Bit clock and word clock will continue to be transmitted when in master mode, even if codec is

powered down

D3

D2

R/W

0

Reserved. Only write zero to this register.

3-D Effect Control

0: Disable 3-D digital effect processing

1: Enable 3-D digital effect processing

D1-D0

R/W

00

Reserved. Only write 00 to this register

Page 0 / Register 9:

Audio Serial Data Interface Control Register B

BIT

READ/ RESET

WRITE VALUE

DESCRIPTION

D7–D6

R/W

00

0

Audio Serial Data Interface Transfer Mode

00: Serial data bus uses I2S mode

01: Serial data bus uses DSP mode

10: Serial data bus uses right-justified mode

11: Serial data bus uses left-justified mode

D5–D4

D3

Audio Serial Data Word Length Control

00: Audio data word length = 16-bits

01: Audio data word length = 20-bits

10: Audio data word length = 24-bits

11: Audio data word length = 32-bits

Bit Clock Rate Control

This register only has effect when bit clock is programmed as an output

0: Continuous-transfer mode used to determine master mode bit clock rate

1: 256-clock transfer mode used, resulting in 256 bit clocks per frame

D2

D1

D0

R/W

0

DAC Re-Sync

0: Don’t Care

1:

Re-Sync Stereo DAC with Codec Interface if the group delay changes by more than ±DACFS/4.

ADC Re-Sync

0: Don’t Care

1:

Re-Sync Stereo ADC with Codec Interface if the group delay changes by more than ±ADCFS/4.

Re-Sync Mute Behavior

0: Re-Sync is done without soft-muting the channel. (ADC/DAC)

1: Re-Sync is done by internally soft-muting the channel. (ADC/DAC)

Submit Documentation Feedback

41

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 10:

Audio Serial Data Interface Control Register C

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D0

R/W

00000000

Audio Serial Data Word Offset Control

This register determines where valid data is placed or expected in each frame, by controlling

the offset from beginning of the frame where valid data begins. The offset is measured from

the rising edge of word clock when in DSP mode.

00000000: Data offset = 0 bit clocks

00000001: Data offset = 1 bit clock

00000010: Data offset = 2 bit clocks

…

Note: In continuous transfer mode the maximum offset is 17 for I2S/LJF/RJF modes and 16

for DSP mode. In 256-clock mode, the maximum offset is 242 for I2S/LJF/RJF and 241 for

DSP modes.

11111110: Data offset = 254 bit clocks

11111111: Data offset = 255 bit clocks

Page 0 / Register 11:

Audio Codec Overflow Flag Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R

0

Left ADC Overflow Flag

This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is

removed. The register bit reset to 0 after it is read.

0: No overflow has occurred

1: An overflow has occurred

D6

D5

R

0

Right ADC Overflow Flag

This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is

removed. The register bit reset to 0 after it is read.

0: No overflow has occurred

1: An overflow has occurred

R

0

Left DAC Overflow Flag

This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is

removed. The register bit reset to 0 after it is read.

0: No overflow has occurred

1: An overflow has occurred

D4

R

0

Right DAC Overflow Flag

This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is

removed. The register bit reset to 0 after it is read.

0: No overflow has occurred

1: An overflow has occurred

D3–D0

R/W

0001

PLL R Value

0000: R = 16

0001 : R = 1

0010 : R = 2

0011 : R = 3

0100 : R = 4

…

1110: R = 14

1111: R = 15

42

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 12:

Audio Codec Digital Filter Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D6

R/W

00

Left ADC Highpass Filter Control

00: Left ADC highpass filter disabled

01: Left ADC highpass filter –3-dB frequency = 0.0045 × ADC Fs

10: Left ADC highpass filter –3-dB frequency = 0.0125 × ADC Fs

11: Left ADC highpass filter –3-dB frequency = 0.025 × ADC Fs

D5–D4

R/W

00

Right ADC Highpass Filter Control

00: Right ADC highpass filter disabled

01: Right ADC highpass filter –3-dB frequency = 0.0045 × ADC Fs

10: Right ADC highpass filter –3-dB frequency = 0.0125 × ADC Fs

11: Right ADC highpass filter –3-dB frequency = 0.025 × ADC Fs

D3

D2

D1

D0

R/W

0

Left DAC Digital Effects Filter Control

0: Left DAC digital effects filter disabled (bypassed)

1: Left DAC digital effects filter enabled

Left DAC De-emphasis Filter Control

0: Left DAC de-emphasis filter disabled (bypassed)

1: Left DAC de-emphasis filter enabled

Right DAC Digital Effects Filter Control

0: Right DAC digital effects filter disabled (bypassed)

1: Right DAC digital effects filter enabled

Right DAC De-emphasis Filter Control

0: Right DAC de-emphasis filter disabled (bypassed)

1: Right DAC de-emphasis filter enabled

Page 0 / Register 13:

Reserved

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D0

R/W

00000000 Reserved. Write Only 00000000 to this register.

Page 0 / Register 14:

Headset Configuration Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Driver Capacitive Coupling

0: Programs high-power outputs for capless driver configuration

1: Programs high-power outputs for ac-coupled driver configuration

D6⁽¹⁾

R/W

0

Stereo Output Driver Configuration A

Note: do not set bits D6 and D3 both high at the same time.

0: A stereo fully-differential output configuration is not being used

1: A stereo fully-differential output configuration is being used

D5–D4

D3⁽¹⁾

R

00

0

Reserved. Write only 00 to these bits.

R/W

Stereo Output Driver Configuration B

Note: do not set bits D6 and D3 both high at the same time.

0: A stereo pseudo-differential output configuration is not being used

1: A stereo pseudo-differential output configuration is being used

D2–D0

R

000

Reserved. Write only zeros to these bits.

(1) Do not set D6 and D3 to 1 simultaneously

Page 0 / Register 15:

Left ADC PGA Gain Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

1

Left ADC PGA Mute

0: The left ADC PGA is not muted

1: The left ADC PGA is muted

Submit Documentation Feedback

43

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 15:

Left ADC PGA Gain Control Register (continued)

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D6-D0

R/W

0000000 Left ADC PGA Gain Setting

0000000: Gain = 0.0-dB

0000001: Gain = 0.5-dB 0000010: Gain = 1.0-dB

…

1110110: Gain = 59.0-dB

1110111: Gain = 59.5-dB

1111000: Gain = 59.5-dB

…

1111111: Gain = 59.5-dB

Page 0 / Register 16:

Right ADC PGA Gain Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

1

Right ADC PGA Mute

0: The right ADC PGA is not muted

1: The right ADC PGA is muted

D6-D0

R/W

0000000 Right ADC PGA Gain Setting

0000000: Gain = 0.0-dB

0000001: Gain = 0.5-dB

0000010: Gain = 1.0-dB

…

1110110: Gain = 59.0-dB

1110111: Gain = 59.5-dB

1111000: Gain = 59.5-dB

…

1111111: Gain = 59.5-dB

Page 0 / Register 17:

MIC3L/R to Left ADC Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

1111

MIC3L Input Level Control for Left ADC PGA Mix

Setting the input level control to a gain below automatically connects MIC3L to the left ADC PGA

mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: MIC3L is not connected to the left ADC PGA

D3-D0

R/W

1111

MIC3R Input Level Control for Left ADC PGA Mix

Setting the input level control to a gain below automatically connects MIC3R to the left ADC PGA

mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: MIC3R is not connected to the left ADC PGA

44

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 18:

MIC3L/R to Right ADC Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D4

R/W

1111

MIC3L Input Level Control for Right ADC PGA Mix

Setting the input level control to a gain below automatically connects MIC3L to the right ADC

PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: MIC3L is not connected to the right ADC PGA

D3–D0

R/W

1111

MIC3R Input Level Control for Right ADC PGA Mix

Setting the input level control to a gain below automatically connects MIC3R to the right ADC

PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: MIC3R is not connected to right ADC PGA

Page 0 / Register 19:

LINE1L to Left ADC Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Reserved. Write Only zero to this bit.

LINE1L Input Level Control for Left ADC PGA Mix

D6–D3

1111

Setting the input level control to a gain below automatically connects LINE1L to the left ADC

PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: LINE1L is not connected to the left ADC PGA

D2

R/W

0

Left ADC Channel Power Control

0: Left ADC channel is powered down

1: Left ADC channel is powered up

D1–D0

00

Left ADC PGA Soft-Stepping Control

00: Left ADC PGA soft-stepping at once per Fs

01: Left ADC PGA soft-stepping at once per two Fs

10–11: Left ADC PGA soft-stepping is disabled

Page x / Register 20:

LINE2L to Left⁽¹⁾ADC Control Register

BIT

READ/ RESET

WRITE VALUE

DESCRIPTION

D7

R/W

0

Reserved. Write only zero to this bit.

(1) LINE1R SEvsFD control is available for both left and right channels. However this setting must be same for both the channels.

Submit Documentation Feedback

45

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page x / Register 20:

LINE2L to Left ADC Control Register (continued)

BIT

READ/ RESET

WRITE VALUE

DESCRIPTION

D6–D3

R/W

1111 LINE2L Input Level Control for Left ADC PGA Mix

Setting the input level control to a gain below automatically connects LINE2L to the left ADC PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: LINE2L is not connected to the left ADC PGA

D2

R/W

R

0

Left ADC Channel Weak Common-Mode Bias Control

0:

1:

Left ADC channel unselected inputs are not biased weakly to the ADC common-mode voltage

Left ADC channel unselected inputs are biased weakly to the ADC common- mode voltage

D1-D0

00

Reserved. Write only zeros to these register bits

Page 0 / Register 21:

LINE1R to Left ADC Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Reserved. Write only zero to this bit.

LINE1R Input Level Control for Left ADC PGA Mix

D6–D3

R/W

1111

Setting the input level control to a gain below automatically connects LINE1R to the left ADC

PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: LINE1R is not connected to the left ADC PGA

D2–D0

R

000

Reserved. Write only zeros to these register bits.

Page 0 / Register 22:

LINE1R to Right ADC Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Reserved. Write only zero to this bit.

LINE1R Input Level Control for Right ADC PGA Mix

D6–D3

1111

Setting the input level control to a gain below automatically connects LINE1R to the right ADC

PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: LINE1R is not connected to the right ADC PGA

D2

R/W

0

Right ADC Channel Power Control

0: Right ADC channel is powered down

1: Right ADC channel is powered up

46

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 22:

LINE1R to Right ADC Control Register (continued)

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D1–D0

R/W

00

Right ADC PGA Soft-Stepping Control

00: Right ADC PGA soft-stepping at once per Fs

01: Right ADC PGA soft-stepping at once per two Fs

10-11: Right ADC PGA soft-stepping is disabled

Page 0 / Register 23:

LINE2R to Right ADC Control Register

BIT

READ/ RESET

WRITE VALUE

DESCRIPTION

D7

R/W

0

Reserved. Write only zero to this bit.

D6–D3

1111 LINE2R Input Level Control for Right ADC PGA Mix

Setting the input level control to a gain below automatically connects LINE2R to the right ADC PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = -–1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001-1110: Reserved. Do not write these sequences to these register bits

1111: LINE2R is not connected to the right ADC PGA

D2

R/W

R

0

Right ADC Channel Weak Common-Mode Bias Control

0:

1:

Right ADC channel unselected inputs are not biased weakly to the ADC common-mode voltage

Right ADC channel unselected inputs are biased weakly to the ADC common- mode voltage

D1–D0

00

Reserved. Write only zeros to these register bits

Page 0 / Register 24:

LINE1L to Right ADC Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Reserved. Write Only zero to this bit.

LINE1L Input Level Control for Right ADC PGA Mix

D6–D3

R/W

1111

Setting the input level control to a gain below automatically connects LINE1L to the right ADC

PGA mix

0000: Input level control gain = 0.0-dB

0001: Input level control gain = –1.5-dB

0010: Input level control gain = –3.0-dB

0011: Input level control gain = –4.5-dB

0100: Input level control gain = –6.0-dB

0101: Input level control gain = –7.5-dB

0110: Input level control gain = –9.0-dB

0111: Input level control gain = –10.5-dB

1000: Input level control gain = –12.0-dB

1001–1110: Reserved. Do not write these sequences to these register bits

1111: LINE1L is not connected to the right ADC PGA

D2–D0

R

000

Reserved. Write only zeros to these register bits.

Page 0 / Register 25:

MICBIAS Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D6

R/W

00

MICBIAS Level Control

00: MICBIAS output is powered down

01: MICBIAS output is powered to 2.0 V

10: MICBIAS output is powered to 2.5 V

11: MICBIAS output is connected to AVDD

D5–D3

D2–D0

R

000

Reserved. Write only zeros to these register bits.

XXX

Submit Documentation Feedback

47

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 26:

Left AGC Control Register A

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Left AGC Enable

0: Left AGC is disabled

1: Left AGC is enabled

D6–D4

R/W

000

Left AGC Target Gain

000: Left AGC target gain = –5.5-dB

001: Left AGC target gain = –8-dB

010: Left AGC target gain = –10-dB

011: Left AGC target gain = –12-dB

100: Left AGC target gain = –14-dB

101: Left AGC target gain = –17-dB

110: Left AGC target gain = –20-dB

111: Left AGC target gain = –24-dB

D3–D2

D1–D0

R/W

00

Left AGC Attack Time

These time constants⁽¹⁾will not be accurate when double rate audio mode is enabled.

00: Left AGC attack time = 8-msec

01: Left AGC attack time = 11-msec

10: Left AGC attack time = 16-msec

11: Left AGC attack time = 20-msec

Left AGC Decay Time

These time constants⁽¹⁾will not be accurate when double rate audio mode is enabled.

00: Left AGC decay time = 100-msec

01: Left AGC decay time = 200-msec

10: Left AGC decay time = 400-msec

11: Left AGC decay time = 500-msec

(1) Time constants are valid when DRA is not enabled. The values would change if DRA is enabled.

Page 0 / Register 27:

Left AGC Control Register B

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D1

R/W

1111111 Left AGC Maximum Gain Allowed

0000000: Maximum gain = 0.0-dB

0000001: Maximum gain = 0.5-dB

0000010: Maximum gain = 1.0-dB

…

1110110: Maximum gain = 59.0-dB

1110111–111111: Maximum gain = 59.5-dB

D0

R/W

0

Reserved. Write only zero to this register bit.

Page 0 / Register 28:

Left AGC Control Register C

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D6

R/W

00

Noise Gate Hysteresis Level Control

00: Hysteresis is disabled

01: Hysteresis = 1-dB

10: Hysteresis = 2-dB

11: Hysteresis = 4-dB

D5–D1

R/W

00000

Left AGC Noise Threshold Control

00000: Left AGC Noise/Silence Detection disabled

00001: Left AGC noise threshold = –30-dB

00010: Left AGC noise threshold = –32-dB

00011: Left AGC noise threshold = –34-dB

…

11101: Left AGC noise threshold = –86-dB

11110: Left AGC noise threshold = –88-dB

11111: Left AGC noise threshold = –90-dB

D0

R/W

0

Left AGC Clip Stepping Control

0: Left AGC clip stepping disabled

1: Left AGC clip stepping enabled

48

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 29:

Right AGC Control Register A

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Right AGC Enable

0: Right AGC is disabled

1: Right AGC is enabled

D6-D4

R/W

000

Right AGC Target Gain

000: Right AGC target gain = –5.5-dB

001: Right AGC target gain = –8-dB

010: Right AGC target gain = –10-dB

011: Right AGC target gain = –12-dB

100: Right AGC target gain = –14-dB

101: Right AGC target gain = –17-dB

110: Right AGC target gain = –20-dB

111: Right AGC target gain = –24-dB

D3–D2

D1–D0

R/W

00

Right AGC Attack Time

These time constants will not be accurate when double rate audio mode is enabled.

00: Right AGC attack time = 8-msec

01: Right AGC attack time = 11-msec

10: Right AGC attack time = 16-msec

11: Right AGC attack time = 20-msec

Right AGC Decay Time

These time constants will not be accurate when double rate audio mode is enabled.

00: Right AGC decay time = 100-msec

01: Right AGC decay time = 200-msec

10: Right AGC decay time = 400-msec

11: Right AGC decay time = 500-msec

Page 0 / Register 30:

Right AGC Control Register B

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D1

R/W

1111111 Right AGC Maximum Gain Allowed

0000000: Maximum gain = 0.0-dB

0000001: Maximum gain = 0.5-dB

0000010: Maximum gain = 1.0-dB

…

1110110: Maximum gain = 59.0-dB

1110111–111111: Maximum gain = 59.5-dB

D0

R/W

0

Reserved. Write only zero to this register bit.

Page 0 / Register 31:

Right AGC Control Register C

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D6

R/W

00

Noise Gate Hysteresis Level Control

00: Hysteresis is disabled

01: Hysteresis = 1-dB

10: Hysteresis = 2-dB

11: Hysteresis = 4-dB

D5–D1

R/W

00000

Right AGC Noise Threshold Control

00000: Right AGC Noise/Silence Detection disabled

00001: Right AGC noise threshold = –30-dB

00010: Right AGC noise threshold = –32-dB

00011: Right AGC noise threshold = –34-dB

…

11101: Right AGC noise threshold = –86-dB

11110: Right AGC noise threshold = –88-dB

11111: Right AGC noise threshold = –90-dB

D0

R/W

0

Right AGC Clip Stepping Control

0: Right AGC clip stepping disabled

1: Right AGC clip stepping enabled

Submit Documentation Feedback

49

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 32:

Left AGC Gain Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D0

R

00000000 Left Channel Gain Applied by AGC Algorithm

11101000: Gain = –12.0-dB

11101001: Gain = –11.5-dB

11101010: Gain = –11.0-dB

…

00000000: Gain = 0.0-dB

00000001: Gain = +0.5-dB

…

01110110: Gain = +59.0-dB

01110111: Gain = +59.5-dB

Page 0 / Register 33:

Right AGC Gain Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R

00000000 Right Channel Gain Applied by AGC Algorithm

11101000: Gain = –12.0-dB

11101001: Gain = –11.5-dB

11101010: Gain = –11.0-dB

…

00000000: Gain = 0.0-dB

00000001: Gain = +0.5-dB

…

01110110: Gain = +59.0-dB

01110111: Gain = +59.5-dB

Page 0 / Register 34:

Left AGC Noise Gate Debounce Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D3

R/W

00000

Left AGC Noise Detection Debounce Control

These times⁽¹⁾will not be accurate when double rate audio mode is enabled.

00000: Debounce = 0-msec

00001: Debounce = 0.5-msec

00010: Debounce = 1-msec

00011: Debounce = 2-msec

00100: Debounce = 4-msec

00101: Debounce = 8-msec

00110: Debounce = 16-msec

00111: Debounce = 32-msec

01000: Debounce = 64×1 = 64ms

01001: Debounce = 64×2 = 128ms

01010: Debounce = 64×3 = 192ms

…

11110: Debounce = 64×23 = 1472ms

11111: Debounce = 64×24 = 1536ms

D2–D0

R/W

000

Left AGC Signal Detection Debounce Control

These times⁽¹⁾will not be accurate when double rate audio mode is enabled.

000: Debounce = 0-msec

001: Debounce = 0.5-msec

010: Debounce = 1-msec

011: Debounce = 2-msec

100: Debounce = 4-msec

101: Debounce = 8-msec

110: Debounce = 16-msec

111: Debounce = 32-msec

(1) Time constants are valid when DRA is not enabled. The values would change when DRA is enabled

50

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 35:

Right AGC Noise Gate Debounce Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D3

R/W

00000

Right AGC Noise Detection Debounce Control

These times⁽¹⁾will not be accurate when double rate audio mode is enabled.

00000: Debounce = 0-msec

00001: Debounce = 0.5-msec

00010: Debounce = 1-msec

00011: Debounce = 2-msec

00100: Debounce = 4-msec

00101: Debounce = 8-msec

00110: Debounce = 16-msec

00111: Debounce = 32-msec

01000: Debounce = 64×1 = 64ms

01001: Debounce = 64×2 = 128ms

01010: Debounce = 64×3 = 192ms

…

11110: Debounce = 64×23 = 1472ms

11111: Debounce = 64×24 = 1536ms

D7–D3

R/W

00000

Right AGC Signal Detection Debounce Control

These times⁽¹⁾will not be accurate when double rate audio mode is enabled.

000: Debounce = 0-msec

001: Debounce = 0.5-msec

010: Debounce = 1-msec

011: Debounce = 2-msec

100: Debounce = 4-msec

101: Debounce = 8-msec

110: Debounce = 16-msec

111: Debounce = 32-msec

(1) Time constants are valid when DRA is not enabled. The values would change when DRA is enabled.

Page 0 / Register 36:

ADC Flag Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R

0

Left ADC PGA Status

0: Applied gain and programmed gain are not the same

1: Applied gain = programmed gain

D6

D5

D4

D3

D2

D1

D0

Left ADC Power Status

0: Left ADC is in a power down state

1: Left ADC is in a power up state

Left AGC Signal Detection Status

0: Signal power is greater than noise threshold

1: Signal power is less than noise threshold

Left AGC Saturation Flag

0: Left AGC is not saturated

1: Left AGC gain applied = maximum allowed gain for left AGC

Right ADC PGA Status

0: Applied gain and programmed gain are not the same

1: Applied gain = programmed gain

Right ADC Power Status

0: Right ADC is in a power down state

1: Right ADC is in a power up state

Right AGC Signal Detection Status

0: Signal power is greater than noise threshold

1: Signal power is less than noise threshold

Right AGC Saturation Flag

0: Right AGC is not saturated

1: Right AGC gain applied = maximum allowed gain for right AGC

Submit Documentation Feedback

51

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 37:

DAC Power and Output Driver Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

Left DAC Power Control

0: Left DAC not powered up

1: Left DAC is powered up

D6

R/W

0

Right DAC Power Control

0: Right DAC not powered up

1: Right DAC is powered up

D5–D4

00

HPLCOM Output Driver Configuration Control

00: HPLCOM configured as differential of HPLOUT

01: HPLCOM configured as constant VCM output

10: HPLCOM configured as independent single-ended output

11: Reserved. Do not write this sequence to these register bits.

D3–D0

R

000

Reserved. Write only zeros to these register bits.

Page 0 / Register 38:

High Power Output Driver Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D6

D5-D3

R

00

Reserved. Write only zeros to these register bits.

HPRCOM Output Driver Configuration Control

R/W

000

000: HPRCOM configured as differential of HPROUT 001: HPRCOM configured as constant VCM

output

010: HPRCOM configured as independent single-ended output

011: HPRCOM configured as differential of HPLCOM 100: HPRCOM configured as external

feedback with HPLCOM as constant VCM output

101–111: Reserved. Do not write these sequences to these register bits.

D2

D1

R/W

0

Short Circuit Protection Control

0: Short circuit protection on all high power output drivers is disabled

1: Short circuit protection on all high power output drivers is enabled

Short Circuit Protection Mode Control

0:

1:

If short circuit protection enabled, it will limit the maximum current to the load

If short circuit protection enabled, it will power down the output driver automatically when a

short is detected

D0

R

0

Reserved. Write only zero to this register bit.

Page 0 / Register 39:

Reserved Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D0

R

00000000 Reserved. Do not write to this register.

Page 0 / Register 40:

High Power Output Stage Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D6

R/W

00

Output Common-Mode Voltage Control

00: Output common-mode voltage = 1.35V

01: Output common-mode voltage = 1.5V

10: Output common-mode voltage = 1.65V

11: Output common-mode voltage = 1.8V

D5–D4

D3–D2

R/W

00

LINE2L Bypass Path Control

00: LINE2L bypass is disabled

01: LINE2L bypass uses LINE2LP single-ended

1X: Reserved. Do not use.

LINE2R Bypass Path Control

00: LINE2R bypass is disabled

01: LINE2R bypass uses LINE2RP single-ended

1X: Reserved. Do not use.

52

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 40:

High Power Output Stage Control Register (continued)

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D1–D0

R/W

00

Output Volume Control Soft-Stepping

00: Output soft-stepping = one step per Fs

01: Output soft-stepping = one step per 2Fs

10: Output soft-stepping disabled

11: Reserved. Do not write this sequence to these register bits.

Page 0 / Register 41:

DAC Output Switching Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7–D6

R/W

00

Left DAC Output Switching Control

00: Left DAC output selects DAC_L1 path

01: Left DAC output selects DAC_L3 path to left line output driver

10: Left DAC output selects DAC_L2 path to left high power output drivers

11: Reserved. Do not write this sequence to these register bits.

(1)

D5–D4

R/W

00

Right DAC Output Switching Control

00: Right DAC output selects DAC_R1 path

01: Right DAC output selects DAC_R3 path to right line output driver

10: Right DAC output selects DAC_R2 path to right high power output drivers

11: Reserved. Do not write this sequence to these register bits.

(1)

D3–D2

D1–D0

R/W

00

Reserved. Write only zeros to these bits.

DAC Digital Volume Control Functionality

00: Left and right DAC channels have independent volume controls

01: Left DAC volume follows the right channel control register

10: Right DAC volume follows the left channel control register

11: Left and right DAC channels have independent volume controls (same as 00)

(1) When using the DAC direct paths (DAC_L2 and DAC_R2), the signal will be gained up by a factor of -1 dB.

Page 0 / Register 42:

Output Driver Pop Reduction Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

Output Driver Power-On Delay Control

0000: Driver power-on time = 0-µsec

0001: Driver power-on time = 10-µsec

0010: Driver power-on time = 100-µsec

0011: Driver power-on time = 1-msec

0100: Driver power-on time = 10-msec

0101: Driver power-on time = 50-msec

0110: Driver power-on time = 100-msec

0111: Driver power-on time = 200-msec

1000: Driver power-on time = 400-msec

1001: Driver power-on time = 800-msec

1010: Driver power-on time = 2-sec

1011: Driver power-on time = 4-sec

1100–1111: Reserved. Do not write these sequences to these register bits.

D3-D2

D1

R/W

00

0

Driver Ramp-up Step Timing Control

00: Driver ramp-up step time = 0-msec

01: Driver ramp-up step time = 1-msec

10: Driver ramp-up step time = 2-msec

11: Driver ramp-up step time = 4-msec

Weak Output Common-mode Voltage Control

0:

1:

Weakly driven output common-mode voltage is generated from bandgap reference

Weakly driven output common-mode voltage is generated from resistor divider off the AVDD

supply

D0

0

Reserved. Write only zero to this register bit.

Submit Documentation Feedback

53

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 43:

Left DAC Digital Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

1

Left DAC Digital Mute

0: The left DAC channel is not muted

1: The left DAC channel is muted

D6–D0

R/W

0000000 Left DAC Digital Volume Control Setting

0000000: Gain = 0.0-dB

0000001: Gain = –0.5-dB

0000010: Gain = –1.0-dB

…

1111101: Gain = –62.5-dB

1111110: Gain = –63.0-dB

1111111: Gain = –63.5-dB

Page 0 / Register 44:

Right DAC Digital Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

1

Right DAC Digital Mute

0: The right DAC channel is not muted

1: The right DAC channel is muted

D6–D0

R/W

0000000 Right DAC Digital Volume Control Setting

0000000: Gain = 0.0-dB

0000001: Gain = –0.5-dB

0000010: Gain = –1.0-dB

…

1111101: Gain = –62.5-dB

1111110: Gain = –63.0-dB

1111111: Gain = –63.5-dB

Output Stage Volume Controls

A basic analog volume control with range from 0 dB to -78 dB and mute is replicated multiple times in the output

stage network, connected to each of the analog signals that route to the output stage. In addition, to enable

completely independent mixing operations to be performed for each output driver, each analog signal coming into

the output stage may have up to seven separate volume controls. These volume controls all have approximately

0.5-dB step programmability over most of the gain range, with steps increasing slightly at the lowest attenuations.

Table 5 lists the detailed gain versus programmed setting for this basic volume control.

Table 5. Output Stage Volume Control Settings and Gains

Gain Setting

Analog Gain

(dB)

Gain Setting

Analog Gain

(dB)

Gain Setting

Analog Gain

(dB)

Gain Setting

Analog Gain

(dB)

0 0.0

1

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

-15.0

-15.5

-16.0

-16.5

-17.0

-17.5

-18.0

-18.6

-19.1

-19.6

-20.1

-20.6

-21.1

-21.6

-22.1

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

-30.1

-30.6

-31.1

-31.6

-32.1

-32.6

-33.1

-33.6

-34.1

-34.6

-35.1

-35.7

-36.1

-36.7

-37.1

90

91

-45.2

-45.8

-46.2

-46.7

-47.4

-47.9

-48.2

-48.7

-49.3

-50.0

-50.3

-51.0

-51.4

-51.8

-52.2

-0.5

-1.0

-1.5

-2.0

-2.5

-3.0

-3.5

-4.0

-4.5

-5.0

-5.5

-6.0

-6.5

-7.0

2

92

3

93

4

94

5

95

6

96

7

97

8

98

9

99

10

11

12

13

14

100

101

102

103

104

54

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Table 5. Output Stage Volume Control Settings and Gains (continued)

Gain Setting

Analog Gain

(dB)

Gain Setting

Analog Gain

(dB)

Gain Setting

Analog Gain

(dB)

Gain Setting

Analog Gain

(dB)

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

-7.5

-8.0

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

-22.6

-23.1

-23.6

-24.1

-24.6

-25.1

-25.6

-26.1

-26.6

-27.1

-27.6

-28.1

-28.6

-29.1

-29.6

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

-37.7

-38.2

-38.7

-39.2

-39.7

-40.2

-40.7

-41.2

-41.7

-42.2

-42.7

-43.2

-43.8

-44.3

-44.8

105

106

-52.7

-53.7

-54.2

-55.3

-56.7

-58.3

-60.2

-62.7

-64.3

-66.2

-68.7

-72.2

-78.3

Mute

-8.5

107

-9.0

108

-9.5

109

-10.0

-10.5

-11.0

-11.5

-12.0

-12.5

-13.0

-13.5

-14.0

-14.5

110

111

112

113

114

115

116

117

118–127

Page 0 / Register 45:

LINE2L to HPLOUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2L Output Routing Control

0: LINE2L is not routed to HPLOUT

1: LINE2L is routed to HPLOUT

D6-D0

R/W

0000000 LINE2L to HPLOUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 46:

PGA_L to HPLOUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_L Output Routing Control

0: PGA_L is not routed to HPLOUT

1: PGA_L is routed to HPLOUT

D6-D0

R/W

0000000 PGA_L to HPLOUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 47:

DAC_L1 to HPLOUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_L1 Output Routing Control

0: DAC_L1 is not routed to HPLOUT

1: DAC_L1 is routed to HPLOUT

D6-D0

R/W

0000000 DAC_L1 to HPLOUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 48:

LINE2R to HPLOUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2R Output Routing Control

0: LINE2R is not routed to HPLOUT

1: LINE2R is routed to HPLOUT

D6-D0

R/W

0000000 LINE2R to HPLOUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Submit Documentation Feedback

55

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 49:

PGA_R to HPLOUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_R Output Routing Control

0: PGA_R is not routed to HPLOUT

1: PGA_R is routed to HPLOUT

D6-D0

R/W

0000000 PGA_R to HPLOUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 50:

DAC_R1 to HPLOUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_R1 Output Routing Control

0: DAC_R1 is not routed to HPLOUT

1: DAC_R1 is routed to HPLOUT

D6-D0

R/W

0000000

DAC_R1 to HPLOUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 51:

HPLOUT Output Level Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

HPLOUT Output Level Control

0000: Output level control = 0-dB

0001: Output level control = 1-dB

0010: Output level control = 2-dB

...

1000: Output level control = 8-dB

1001: Output level control = 9-dB

1010–1111: Reserved. Do not write these sequences to these register bits.

D3

D2

D1

D0

R/W

R

0

1

0

HPLOUT Mute

0: HPLOUT is muted

1: HPLOUT is not muted

HPLOUT Power Down Drive Control

0: HPLOUT is weakly driven to a common-mode when powered down

1: HPLOUT is tri-stated with powered down

HPLOUT Volume Control Status

0: Not all programmed gains to HPLOUT have been applied yet

1: All programmed gains to HPLOUT have been applied

R/W

HPLOUT Power Control

0: HPLOUT is not fully powered up

1: HPLOUT is fully powered up

Page 0 / Register 52:

LINE2L to HPLCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2L Output Routing Control

0: LINE2L is not routed to HPLCOM

1: LINE2L is routed to HPLCOM

D6-D0

R/W

0000000 LINE2L to HPLCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 53:

PGA_L to HPLCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_L Output Routing Control

0: PGA_L is not routed to HPLCOM

1: PGA_L is routed to HPLCOM

D6-D0

R/W

0000000 PGA_L to HPLCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

56

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 54:

DAC_L1 to HPLCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_L1 Output Routing Control

0: DAC_L1 is not routed to HPLCOM

1: DAC_L1 is routed to HPLCOM

D6-D0

R/W

0000000

DAC_L1 to HPLCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 55:

LINE2R to HPLCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2R Output Routing Control

0: LINE2R is not routed to HPLCOM

1: LINE2R is routed to HPLCOM

D6-D0

R/W

0000000

LINE2R to HPLCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 56:

PGA_R to HPLCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_R Output Routing Control

0: PGA_R is not routed to HPLCOM

1: PGA_R is routed to HPLCOM

D6-D0

R/W

0000000

PGA_R to HPLCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 57:

DAC_R1 to HPLCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_R1 Output Routing Control

0: DAC_R1 is not routed to HPLCOM

1: DAC_R1 is routed to HPLCOM

D6-D0

R/W

0000000

DAC_R1 to HPLCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 58:

HPLCOM Output Level Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

HPLCOM Output Level Control

0000: Output level control = 0-dB

0001: Output level control = 1-dB

0010: Output level control = 2-dB

...

1000: Output level control = 8-dB

1001: Output level control = 9-dB

1010–1111: Reserved. Do not write these sequences to these register bits.

D3

D2

D1

D0

R/W

R

0

1

0

HPLCOM Mute

0: HPLCOM is muted

1: HPLCOM is not muted

HPLCOM Power Down Drive Control

0: HPLCOM is weakly driven to a common-mode when powered down

1: HPLCOM is tri-stated with powered down

HPLCOM Volume Control Status

0: Not all programmed gains to HPLCOM have been applied yet

1: All programmed gains to HPLCOM have been applied

R/W

HPLCOM Power Control

0: HPLCOM is not fully powered up

1: HPLCOM is fully powered up

Submit Documentation Feedback

57

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 59:

LINE2L to HPROUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2L Output Routing Control

0: LINE2L is not routed to HPROUT

1: LINE2L is routed to HPROUT

D6-D0

R/W

0000000

LINE2L to HPROUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 60:

PGA_L to HPROUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_L Output Routing Control

0: PGA_L is not routed to HPROUT

1: PGA_L is routed to HPROUT

D6-D0

R/W

0000000

PGA_L to HPROUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 61:

DAC_L1 to HPROUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_L1 Output Routing Control

0: DAC_L1 is not routed to HPROUT

1: DAC_L1 is routed to HPROUT

D6-D0

R/W

0000000

DAC_L1 to HPROUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 62:

LINE2R to HPROUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2R Output Routing Control

0: LINE2R is not routed to HPROUT

1: LINE2R is routed to HPROUT

D6-D0

R/W

0000000

LINE2R to HPROUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 63:

PGA_R to HPROUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_R Output Routing Control

0: PGA_R is not routed to HPROUT

1: PGA_R is routed to HPROUT

D6-D0

R/W

0000000

PGA_R to HPROUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 64:

DAC_R1 to HPROUT Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_R1 Output Routing Control

0: DAC_R1 is not routed to HPROUT

1: DAC_R1 is routed to HPROUT

D6-D0

R/W

0000000

DAC_R1 to HPROUT Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

58

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 65:

HPROUT Output Level Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

HPROUT Output Level Control

0000: Output level control = 0-dB

0001: Output level control = 1-dB

0010: Output level control = 2-dB

...

1000: Output level control = 8-dB

1001: Output level control = 9-dB

1010–1111: Reserved. Do not write these sequences to these register bits.

D3

D2

D1

D0

R/W

R

0

1

0

HPROUT Mute

0: HPROUT is muted

1: HPROUT is not muted

HPROUT Power Down Drive Control

0: HPROUT is weakly driven to a common-mode when powered down

1: HPROUT is tri-stated with powered down

HPROUT Volume Control Status

0: Not all programmed gains to HPROUT have been applied yet

1: All programmed gains to HPROUT have been applied

R/W

HPROUT Power Control

0: HPROUT is not fully powered up

1: HPROUT is fully powered up

Page 0 / Register 66:

LINE2L to HPRCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2L Output Routing Control

0: LINE2L is not routed to HPRCOM

1: LINE2L is routed to HPRCOM

D6-D0

R/W

0000000

LINE2L to HPRCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 67:

PGA_L to HPRCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_L Output Routing Control

0: PGA_L is not routed to HPRCOM

1: PGA_L is routed to HPRCOM

D6-D0

R/W

0000000

PGA_L to HPRCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 68:

DAC_L1 to HPRCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_L1 Output Routing Control

0: DAC_L1 is not routed to HPRCOM

1: DAC_L1 is routed to HPRCOM

D6-D0

R/W

0000000

DAC_L1 to HPRCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 69:

LINE2R to HPRCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2R Output Routing Control

0: LINE2R is not routed to HPRCOM

1: LINE2R is routed to HPRCOM

D6-D0

R/W

0000000 LINE2R to HPRCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Submit Documentation Feedback

59

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 70:

PGA_R to HPRCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_R Output Routing Control

0: PGA_R is not routed to HPRCOM

1: PGA_R is routed to HPRCOM

D6-D0

R/W

0000000 PGA_R to HPRCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 71:

DAC_R1 to HPRCOM Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_R1 Output Routing Control

0: DAC_R1 is not routed to HPRCOM

1: DAC_R1 is routed to HPRCOM

D6-D0

R/W

0000000 DAC_R1 to HPRCOM Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 72:

HPRCOM Output Level Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

HPRCOM Output Level Control

0000: Output level control = 0-dB

0001: Output level control = 1-dB

0010: Output level control = 2-dB

...

1000: Output level control = 8-dB

1001: Output level control = 9-dB

1010–1111: Reserved. Do not write these sequences to these register bits.

D3

D2

D1

D0

R/W

R

0

1

0

HPRCOM Mute

0: HPRCOM is muted

1: HPRCOM is not muted

HPRCOM Power Down Drive Control

0: HPRCOM is weakly driven to a common-mode when powered down

1: HPRCOM is tri-stated with powered down

HPRCOM Volume Control Status

0: Not all programmed gains to HPRCOM have been applied yet

1: All programmed gains to HPRCOM have been applied

R/W

HPRCOM Power Control

0: HPRCOM is not fully powered up

1: HPRCOM is fully powered up

Page 0 / Registers 73–78:

Reserved Registers

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

00000000 Reserved. Write only 00000000 to these registers.

Page 0 / Register 79:

Reserved Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

00000010 Reserved. Write only 00000010 to this register.

Page 0 / Register 80:

LINE2L to LEFT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2L Output Routing Control

0: LINE2L is not routed to LEFT_LOP/M

1: LINE2L is routed to LEFT_LOP/M

60

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 80:

LINE2L to LEFT_LOP/M Volume Control Register (continued)

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D6-D0

R/W

0000000

LINE2L to LEFT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 81:

PGA_L to LEFT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_L Output Routing Control

0: PGA_L is not routed to LEFT_LOP/M

1: PGA_L is routed to LEFT_LOP/M

D6-D0

R/W

0000000

PGA_L to LEFT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 82:

DAC_L1 to LEFT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_L1 Output Routing Control

0: DAC_L1 is not routed to LEFT_LOP/M

1: DAC_L1 is routed to LEFT_LOP/M

D6-D0

R/W

0000000

DAC_L1 to LEFT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 83:

LINE2R to LEFT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2R Output Routing Control

0: LINE2R is not routed to LEFT_LOP/M

1: LINE2R is routed to LEFT_LOP/M

D6-D0

R/W

0000000

LINE2R to LEFT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 84:

PGA_R to LEFT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_R Output Routing Control

0: PGA_R is not routed to LEFT_LOP/M

1: PGA_R is routed to LEFT_LOP/M

D6-D0

R/W

0000000 PGA_R to LEFT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 85:

DAC_R1 to LEFT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_R1 Output Routing Control

0: DAC_R1 is not routed to LEFT_LOP/M

1: DAC_R1 is routed to LEFT_LOP/M

D6-D0

R/W

0000000

DAC_R1 to LEFT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Submit Documentation Feedback

61

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 86:

LEFT_LOP/M Output Level Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

LEFT_LOP/M Output Level Control

0000: Output level control = 0-dB

0001: Output level control = 1-dB

0010: Output level control = 2-dB

...

1000: Output level control = 8-dB

1001: Output level control = 9-dB

1010–1111: Reserved. Do not write these sequences to these register bits.

D3

0

LEFT_LOP/M Mute

0: LEFT_LOP/M is muted

1: LEFT_LOP/M is not muted

D2

D1

R/W

R

0

1

Reserved. Write only zero to this register bit.

LEFT_LOP/M Volume Control Status

0: Not all programmed gains to LEFT_LOP/M have been applied yet

1: All programmed gains to LEFT_LOP/M have been applied

D0

R/W

0

LEFT_LOP/M Power Control

0: LEFT_LOP/M is not fully powered up

1: LEFT_LOP/M is fully powered up

Page 0 / Register 87:

LINE2L to RIGHT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2L Output Routing Control

0: LINE2L is not routed to RIGHT_LOP/M

1: LINE2L is routed to RIGHT_LOP/M

D6-D0

R/W

0000000

LINE2L to RIGHT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 88:

PGA_L to RIGHT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_L Output Routing Control

0: PGA_L is not routed to RIGHT_LOP/M

1: PGA_L is routed to RIGHT_LOP/M

D6-D0

R/W

0000000

PGA_L to RIGHT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 89:

DAC_L1 to RIGHT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_L1 Output Routing Control

0: DAC_L1 is not routed to RIGHT_LOP/M

1: DAC_L1 is routed to RIGHT_LOP/M

D6-D0

R/W

0000000

DAC_L1 to RIGHT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 90:

LINE2R to RIGHT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

LINE2R Output Routing Control

0: LINE2R is not routed to RIGHT_LOP/M

1: LINE2R is routed to RIGHT_LOP/M

D6-D0

R/W

0000000

LINE2R to RIGHT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

62

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 91:

PGA_R to RIGHT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

PGA_R Output Routing Control

0: PGA_R is not routed to RIGHT_LOP/M

1: PGA_R is routed to RIGHT_LOP/M

D6-D0

R/W

0000000

PGA_R to RIGHT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 92:

DAC_R1 to RIGHT_LOP/M Volume Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R/W

0

DAC_R1 Output Routing Control

0: DAC_R1 is not routed to RIGHT_LOP/M

1: DAC_R1 is routed to RIGHT_LOP/M

D6-D0

R/W

0000000

DAC_R1 to RIGHT_LOP/M Analog Volume Control

For 7-bit register setting versus analog gain values, see Table 5

Page 0 / Register 93:

RIGHT_LOP/M Output Level Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D4

R/W

0000

RIGHT_LOP/M Output Level Control

0000: Output level control = 0-dB

0001: Output level control = 1-dB

0010: Output level control = 2-dB

...

1000: Output level control = 8-dB

1001: Output level control = 9-dB

1010–1111: Reserved. Do not write these sequences to these register bits.

D3

R/W

0

RIGHT_LOP/M Mute

0: RIGHT_LOP/M is muted

1: RIGHT_LOP/M is not muted

D2

D1

R/W

R

0

1

Reserved. Write only zero to this register bit.

RIGHT_LOP/M Volume Control Status

0: Not all programmed gains to RIGHT_LOP/M have been applied yet

1: All programmed gains to RIGHT_LOP/M have been applied

D0

R/W

0

RIGHT_LOP/M Power Control

0: RIGHT_LOP/M is not fully powered up

1: RIGHT_LOP/M is fully powered up

Page 0 / Register 94:

Module Power Status Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R

0

Left DAC Power Status

0: Left DAC not fully powered up

1: Left DAC fully powered up

D6

R

0

Right DAC Power Status

0: Right DAC not fully powered up

1: Right DAC fully powered up

D5

D4

R

0

Reserved. Write only zero to this bit.

LEFT_LOP/M Power Status

0: LEFT_LOP/M output driver powered down

1: LEFT_LOP/M output driver powered up

D3

D2

R

0

RIGHT_LOP/M Power Status

0: RIGHT_LOP/M is not fully powered up

1: RIGHT_LOP/M is fully powered up

HPLOUT Driver Power Status

0: HPLOUT Driver is not fully powered up

1: HPLOUT Driver is fully powered up

Submit Documentation Feedback

63

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 0 / Register 94:

Module Power Status Register (continued)

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D1

R/W

0

HPROUT Driver Power Status

0: HPROUT Driver is not fully powered up

1: HPROUT Driver is fully powered up

D0

R

0

Reserved. Do not write to this register bit.

Page 0 / Register 95:

Output Driver Short Circuit Detection Status Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R

0

HPLOUT Short Circuit Detection Status

0: No short circuit detected at HPLOUT

1: Short circuit detected at HPLOUT

D6

D5

R

0

HPROUT Short Circuit Detection Status

0: No short circuit detected at HPROUT

1: Short circuit detected at HPROUT

0

HPLCOM Short Circuit Detection Status

0: No short circuit detected at HPLCOM

1: Short circuit detected at HPLCOM

D4

0

HPRCOM Short Circuit Detection Status

0: No short circuit detected at HPRCOM

1: Short circuit detected at HPRCOM

D3

0

HPLCOM Power Status

0: HPLCOM is not fully powered up

1: HPLCOM is fully powered up

D2

0

HPRCOM Power Status

0: HPRCOM is not fully powered up

1: HPRCOM is fully powered up

D1-D0

00

Reserved. Do not write to these register bits.

Page 0 / Register 96:

Sticky Interrupt Flags Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R

0

HPLOUT Short Circuit Detection Status

0: No short circuit detected at HPLOUT driver

1: Short circuit detected at HPLOUT driver

D6

D5

D4

0

HPROUT Short Circuit Detection Status

0: No short circuit detected at HPROUT driver

1: Short circuit detected at HPROUT driver

HPLCOM Short Circuit Detection Status

0: No short circuit detected at HPLCOM driver

1: Short circuit detected at HPLCOM driver

HPRCOM Short Circuit Detection Status

0: No short circuit detected at HPRCOM driver

1: Short circuit detected at HPRCOM driver

D3-D2

D1

R

00

0

Reserved. Write only 00 to these bits.

Left ADC AGC Noise Gate Status

0: Left ADC Signal Power Greater than Noise Threshold for Left AGC

1: Left ADC Signal Power Lower than Noise Threshold for Left AGC

D0

R

0

Right ADC AGC Noise Gate Status

0: Right ADC Signal Power Greater than Noise Threshold for Right AGC

1: Right ADC Signal Power Lower than Noise Threshold for Right AGC

64

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 0 / Register 97:

Real-time Interrupt Flags Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7

R

0

HPLOUT Short Circuit Detection Status

0: No short circuit detected at HPLOUT driver

1: Short circuit detected at HPLOUT driver

D6

D5

D4

0

HPROUT Short Circuit Detection Status

0: No short circuit detected at HPROUT driver

1: Short circuit detected at HPROUT driver

HPLCOM Short Circuit Detection Status

0: No short circuit detected at HPLCOM driver

1: Short circuit detected at HPLCOM driver

HPRCOM Short Circuit Detection Status

0: No short circuit detected at HPRCOM driver

1: Short circuit detected at HPRCOM driver

D3-D2

D1

R

00

0

Reserved. Write only 00 to these bits.

Left ADC AGC Noise Gate Status

0: Left ADC Signal Power Greater than Noise Threshold for Left AGC

1: Left ADC Signal Power Lower than Noise Threshold for Left AGC

D0

R

0

Right ADC AGC Noise Gate Status

0: Right ADC Signal Power Greater than Noise Threshold for Right AGC

1: Right ADC Signal Power Lower than Noise Threshold for Right AGC

Page 0 / Register 98–100:

Reserved Registers

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

00000000

Reserved. Write only 00000000 to these bits.

Page 0 / Register 101:

Additional Clock Control Register

BIT

READ/

WRITE

RESET

DESCRIPTION

VALUE

0000000

0

D7-D1

D0

R/W

Reserved. Write only 0000000 to these bits.

CODEC_CLKIN Source Selection

0: CODEC_CLKIN uses PLLDIV_OUT

1: CODEC_CLKIN uses CLKDIV_OUT

Page 0 / Register 102:

Clock Generation Control Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D6

R/W

00

CLKDIV_IN Source Selection

00: CLKDIV_IN uses MCLK

01: Reserved. Do not use.

10: CLKDIV_IN uses BCLK

11: Reserved. Do not use.

D5-D4

D3-D0

00

PLLCLK_IN Source Selection

00: PLLCLK_IN uses MCLK

01: Reserved. Do not use.

10: PLLCLK _IN uses BCLK

11: Reserved. Do not use.

0010

Reserved. Write only 0010 to these bits.

Page 0 / Register 103–127:

Reserved Registers

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R

00000000

Reserved. Do not write to these registers.

Submit Documentation Feedback

65

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 1 / Register 0:

Page Select Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D1

D0

X

0000000

0

Reserved, write only zeros to these register bits

R/W

Page Select Bit

Writing zero to this bit sets Page-0 as the active page for following register accesses. Writing a one to

this bit sets Page-1 as the active page for following register accesses. It is recommended that the user

read this register bit back after each write, to ensure that the proper page is being accessed for future

register read/writes. This register has the same functionality on page-0 and page-1.

Page 1 / Register 1:

Left Channel Audio Effects Filter N0 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x6B

Left Channel Audio Effects Filter N0 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 2:

Left Channel Audio Effects Filter N0 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xE3

Left Channel Audio Effects Filter N0 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 3:

Left Channel Audio Effects Filter N1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x96

Left Channel Audio Effects Filter N1 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 4:

Left Channel Audio Effects Filter N1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x66

Left Channel Audio Effects Filter N1 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 5:

Left Channel Audio Effects Filter N2 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x67

Left Channel Audio Effects Filter N2 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 6:

Left Channel Audio Effects Filter N2 Coefficient LSB

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x5D

Left Channel Audio Effects Filter N2 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

66

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 1 / Register 7:

Left Channel Audio Effects Filter N3 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x6B

Left Channel Audio Effects Filter N3 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 8:

Left Channel Audio Effects Filter N3 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xE3

Left Channel Audio Effects Filter N3 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 9:

Left Channel Audio Effects Filter N4 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x96

Left Channel Audio Effects Filter N4 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 10:

Left Channel Audio Effects Filter N4 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x66

Left Channel Audio Effects Filter N4 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s

complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 11:

Left Channel Audio Effects Filter N5 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x67

Left Channel Audio Effects Filter N5 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 12:

Left Channel Audio Effects Filter N5 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x5D

Left Channel Audio Effects Filter N5 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from -32768 to +32767.

Page 1 / Register 13:

Left Channel Audio Effects Filter D1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7D

Left Channel Audio Effects Filter D1 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 14:

Left Channel Audio Effects Filter D1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x83

Left Channel Audio Effects Filter D1 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Submit Documentation Feedback

67

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 1 / Register 15:

Left Channel Audio Effects Filter D2 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x84

Left Channel Audio Effects Filter D2 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 16:

Left Channel Audio Effects Filter D2 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xEE

Left Channel Audio Effects Filter D2 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 17:

Left Channel Audio Effects Filter D4 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7D

Left Channel Audio Effects Filter D4 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 18:

Left Channel Audio Effects Filter D4 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x83

Left Channel Audio Effects Filter D4 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 19:

Left Channel Audio Effects Filter D5 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x84

Left Channel Audio Effects Filter D5 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 20:

Left Channel Audio Effects Filter D5 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xEE

Left Channel Audio Effects Filter D5 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 21:

Left Channel De-emphasis Filter N0 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x39

Left Channel De-emphasis Filter N0 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 22:

Left Channel De-emphasis Filter N0 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x55

Left Channel De-emphasis Filter N0 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

68

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 1 / Register 23:

Left Channel De-emphasis Filter N1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xF3

Left Channel De-emphasis Filter N1 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 24:

Left Channel De-emphasis Filter N1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x2D

Left Channel De-emphasis Filter N1 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 25:

Left Channel De-emphasis Filter D1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x53

Left Channel De-emphasis Filter A0 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 26:

Left Channel De-emphasis Filter D1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7E

Left Channel De-emphasis Filter A0 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 27:

Right Channel Audio Effects Filter N0 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x6B

Right Channel Audio Effects Filter N0 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 28:

Right Channel Audio Effects Filter N0 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xE3

Right Channel Audio Effects Filter N0 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 29:

Right Channel Audio Effects Filter N1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x96

Right Channel Audio Effects Filter N1 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 30:

Right Channel Audio Effects Filter N1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x66

Right Channel Audio Effects Filter N1 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Submit Documentation Feedback

69

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 1 / Register 31:

Right Channel Audio Effects Filter N2 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x67

Right Channel Audio Effects Filter N2 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 32:

Right Channel Audio Effects Filter N2 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x5D

Right Channel Audio Effects Filter N2 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 33:

Right Channel Audio Effects Filter N3 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x6B

Right Channel Audio Effects Filter N3 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 34:

Right Channel Audio Effects Filter N3 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xE3

Right Channel Audio Effects Filter N3 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 35:

Right Channel Audio Effects Filter N4 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x96

Right Channel Audio Effects Filter N4 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 36:

Right Channel Audio Effects Filter N4 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x66

Right Channel Audio Effects Filter N4 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 37:

Right Channel Audio Effects Filter N5 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x67

Right Channel Audio Effects Filter N5 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 38:

Right Channel Audio Effects Filter N5 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x5D

Right Channel Audio Effects Filter N5 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

70

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 1 / Register 39:

Right Channel Audio Effects Filter D1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7D

Right Channel Audio Effects Filter D1 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 40:

Right Channel Audio Effects Filter D1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x83

Right Channel Audio Effects Filter D1 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 41:

Right Channel Audio Effects Filter D2 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x84

Right Channel Audio Effects Filter D2 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 42:

Right Channel Audio Effects Filter D2 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xEE

Right Channel Audio Effects Filter D2 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 43:

Right Channel Audio Effects Filter D4 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7D

Right Channel Audio Effects Filter D4 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 44:

Right Channel Audio Effects Filter D4 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x83

Right Channel Audio Effects Filter D4 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 45:

Right Channel Audio Effects Filter D5 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x84

Right Channel Audio Effects Filter D5 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 46:

Right Channel Audio Effects Filter D5 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xEE

Right Channel Audio Effects Filter D5 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Submit Documentation Feedback

71

Product Folder Link(s): TLV320AIC32

TLV320AIC32

SLAS479C–AUGUST 2005–REVISED DECEMBER 2008............................................................................................................................................. www.ti.com

Page 1 / Register 47:

Right Channel De-emphasis Filter N0 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x39

Right Channel De-emphasis Filter N0 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 48:

Right Channel De-emphasis Filter N0 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x55

Right Channel De-emphasis Filter N0 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 49:

Right Channel De-emphasis Filter N1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xF3

Right Channel De-emphasis Filter N1 Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 50:

Right Channel De-emphasis Filter N1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x2D

Right Channel De-emphasis Filter N1 Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 51:

Right Channel De-emphasis Filter D1 Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x53

Right Channel De-emphasis Filter A0 Coefficient MSB The 16-bit integer contained in the MSB

and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible

values ranging from –32768 to +32767.

Page 1 / Register 52:

Right Channel De-emphasis Filter D1 Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7E

Right Channel De-emphasis Filter A0 Coefficient LSB The 16-bit integer contained in the MSB and

LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values

ranging from –32768 to +32767.

Page 1 / Register 53:

3-D Attenuation Coefficient MSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0x7F

3-D Attenuation Coefficient MSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

Page 1 / Register 54:

3-D Attenuation Coefficient LSB Register

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R/W

0xFF

3-D Attenuation Coefficient LSB

The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a

2’s complement integer, with possible values ranging from –32768 to +32767.

72

Submit Documentation Feedback

Product Folder Link(s): TLV320AIC32

TLV320AIC32

www.ti.com ............................................................................................................................................. SLAS479C–AUGUST 2005–REVISED DECEMBER 2008

Page 1 / Register 55–127:

Reserved Registers

BIT

READ/

WRITE

RESET

VALUE

DESCRIPTION

D7-D0

R

0x00

Reserved. Do not write to these registers.

Submit Documentation Feedback

73

Product Folder Link(s): TLV320AIC32

PACKAGE MATERIALS INFORMATION

www.ti.com

27-Jul-2013

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device

Package Package Pins

Type Drawing

SPQ

Reel

A0

B0

K0

P1

W

Pin1

Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant

(mm) W1 (mm)

TLV320AIC32IRHBR

TLV320AIC32IRHBT

VQFN

RHB

32

3000

250

330.0

180.0

12.4

5.3

1.5

8.0

12.0

Q2

Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com

27-Jul-2013

*All dimensions are nominal

Device

Package Type Package Drawing Pins

SPQ

Length (mm) Width (mm) Height (mm)

TLV320AIC32IRHBR

TLV320AIC32IRHBT

VQFN

RHB

32

3000

250

338.1

210.0

338.1

185.0

20.6

35.0

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products

Applications

Audio

www.ti.com/audio

amplifier.ti.com

dataconverter.ti.com

www.dlp.com

Automotive and Transportation www.ti.com/automotive

Communications and Telecom www.ti.com/communications

Amplifiers

Data Converters

DLP® Products

DSP

Computers and Peripherals

Consumer Electronics

Energy and Lighting

Industrial

www.ti.com/computers

www.ti.com/consumer-apps

www.ti.com/energy

dsp.ti.com

Clocks and Timers

Interface

www.ti.com/clocks

interface.ti.com

logic.ti.com

www.ti.com/industrial

www.ti.com/medical

Medical

Logic

Security

www.ti.com/security

Power Mgmt

Microcontrollers

RFID

power.ti.com

Space, Avionics and Defense

Video and Imaging

www.ti.com/space-avionics-defense

www.ti.com/video

microcontroller.ti.com

www.ti-rfid.com

www.ti.com/omap

OMAP Applications Processors

Wireless Connectivity

TI E2E Community

e2e.ti.com

www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265


型号：	TLV320AIC32IRHBG4
厂家：	TEXAS INSTRUMENTS
描述：	SPECIALTY CONSUMER CIRCUIT, PQCC32, 5 X 5 MM, GREEN, PLASTIC, QFN-32 商用集成电路
文件：	总81页 (文件大小：1575K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TLV320AIC32IRHBG4 [TI]

相关型号：

TLV320AIC32IRHBR

TLV320AIC32IRHBR

TLV320AIC32IRHBRG4

TLV320AIC32IRHBT

TLV320AIC32IRHBT

TLV320AIC32IRHBTG4

TLV320AIC32_07

TLV320AIC33

TLV320AIC33

TLV320AIC33IGQE

TLV320AIC33IGQER

TLV320AIC33IGVX