TLV62565 [TI]
TLV6256x 1.5-A High Efficiency Step-Down Converters in SOT-23 5-Pin Package;
| 型号： | TLV62565 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | TLV6256x 1.5-A High Efficiency Step-Down Converters in SOT-23 5-Pin Package |
| 文件： | 总27页 (文件大小：1040K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
TLV6256x 1.5-A High Efficiency Step-Down Converters in SOT-23 5-Pin Package
1 Features
3 Description
The TLV62565/6 devices are synchronous step-down
converters optimized for small solution size and high
efficiency. The devices integrate switches capable of
delivering an output current up to 1.5 A.
1
•
2.7-V to 5.5-V Input Voltage Range
1.5-MHz Typical Switching Frequency
Output Current up to 1.5 A (Max)
Adaptive On-Time Current Control
Power Save Mode for Light Load Efficiency
50-µA Operating Quiescent Current
Up to 95% Efficiency
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The devices are based on an adaptive on time with
valley current mode control scheme. Typical
operating frequency is 1.5 MHz at medium to heavy
loads. The devices are optimized to achieve very low
output voltage ripple even with small external
components and feature an excellent load transient
response.
Over Current Protection
95% Maximum Duty Cycle
Excellent AC and Transient Load Response
Power Good Output, TLV62566
Internal Soft Startup of 250 µs (Typ)
Adjustable Output Voltage
During a light load, the TLV62565/6 automatically
enter into Power Save Mode at the lowest quiescent
current (50 μA typ) to maintain high efficiency over
the entire load current range. In shutdown, the
current consumption is reduced to less than 1 μA.
Thermal Shutdown Protection
The TLV62565/6 provide an adjustable output voltage
via an external resistor divider. The output voltage
start-up ramp is controlled by an internal soft start,
typically 250 µs. Power sequencing is possible by
configuring the Enable (TLV62565) and Power Good
(TLV62566) pins. Other features like over current
protection and over temperature protection are built-
in. The TLV62565/6 devices are available in a SOT-
23 5-pin package.
Available in SOT-23 5-Pin Package
2 Applications
•
•
•
•
•
Portable Devices
DSL Modems
Hard Disk Drivers
Set Top Box
Tablet
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TLV62565,
TLV62566
SOT-23 (5)
2.90 mm × 1.60 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
L1
2.2µH
VOUT
1.8V
VIN
Efficiency vs Load Current
VIN
EN
SW
FB
2.7V to 5.5V
C1
4.7µF
R1
240k
C2
10µF
100
VOUT=1. 8V
90
GND
R2
120k
80
70
60
50
40
30
TLV62565
VIN=2.7V
20
10
0
V
=3.6V
IN
V
=5.5V
IN
10µ
100µ
1m
10m
100m
1
C001
Load current [A]
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
Table of Contents
10.4 Device Functional Modes...................................... 12
11 Application and Implementation........................ 13
11.1 Application Information.......................................... 13
11.2 Typical Application ................................................ 13
12 Power Supply Recommendations ..................... 17
13 Layout................................................................... 18
13.1 Layout Guidelines ................................................. 18
13.2 Layout Example .................................................... 18
13.3 Thermal Considerations........................................ 18
14 Device and Documentation Support ................. 19
14.1 Device Support...................................................... 19
14.2 Documentation Support ....................................... 19
14.3 Related Links ........................................................ 19
14.4 Community Resources.......................................... 19
14.5 Trademarks........................................................... 19
14.6 Electrostatic Discharge Caution............................ 19
14.7 Glossary................................................................ 19
1
2
3
4
5
6
7
8
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Simplified Schematic............................................. 1
Revision History..................................................... 2
Device Comparison Table..................................... 3
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
8.1 Absolute Maximum Ratings ...................................... 4
8.2 ESD Ratings.............................................................. 4
8.3 Recommended Operating Conditions ...................... 4
8.4 Thermal Information.................................................. 4
8.5 Electrical Characteristics.......................................... 5
8.6 Typical Characteristics.............................................. 6
Parameter Measurement Information .................. 8
9
10 Detailed Description ............................................. 9
10.1 Overview ................................................................. 9
10.2 Functional Block Diagrams ................................... 10
10.3 Feature Description............................................... 11
15 Mechanical, Packaging, and Orderable
Information ........................................................... 20
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (December 2014) to Revision C
Page
•
Changed device From: TLV62566 to TLV62565 for EN in the Device Comparison Table ................................................... 3
Changes from Revision A (November 2014) to Revision B
Page
•
•
•
•
Added Storage temperature to Absolute Maximum Ratings .................................................................................................. 4
Changed Handling Ratings to ESD Ratings........................................................................................................................... 4
Deleted Storage temperature from ESD Ratings ................................................................................................................... 4
Changed Thermal Information to Thermal Considerations and moved to Layout section ................................................... 18
Changes from Original (October 2013) to Revision A
Page
•
Changed Added Handling Rating table, Feature Description section, Device Functional Modes, Application and
Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section................................................................ 1
Added "TA = -40°C to 85°C" to the VFB, Feedback regulation voltage Test Conditions ........................................................ 5
Added VFB, Feedback regulation voltage Test Conditions and values for "PWM operation, TA = 85°C"............................... 5
•
•
2
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
6 Device Comparison Table
PART NUMBER
TLV62565
FUNCTION
EN
PG
TLV62566
7 Pin Configuration and Functions
5-Pin SOT-23
DBV Package
(Top View)
FB
VIN
5
4
3
1
2
EN/PG GND SW
Pin Functions
PIN
NUMBER
I/O/PWR
DESCRIPTION
NAME
TLV62565
TLV62566
Device enable logic input. Logic HIGH enables the device, logic low disables the device
and turns it into shutdown.
EN
1
—
I
Feedback pin for the internal control loop. Connect this pin to the external feedback
divider.
FB
5
2
5
2
I
GND
PWR
Ground pin.
Power Good open drain output. This pin is high impedance if the output voltage is within
regulation. It is pulled low if the output is below its nominal value. It is also in logic low
when VIN below UVLO or thermal shutdown triggers.
PG
—
1
O
Switch pin connected to the internal MOSFET switches and inductor terminal. Connect
the inductor of the output filter to this pin.
SW
VIN
3
4
3
4
PWR
PWR
Power supply voltage input.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
8 Specifications
8.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted)(1)
MIN
–0.3
–0.3
–0.3
MAX
7
UNIT
V
VIN, EN,PG
Voltage(2)
SW
FB
VIN+0.3
3.6
V
V
Sink current, IPG
PG
660
µA
Continuous total power dissipation
Operating junction temperature, TJ
Storage temperature, Tstg
See Thermal Information
–40
–65
150
150
°C
°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
8.2 ESD Ratings
VALUE
±2000
±500
UNIT
V
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
Electrostatic
discharge
V(ESD)
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions(1)
MIN
2.7
TYP
MAX UNIT
VIN
TA
Input voltage, VIN
5.5
85
V
Operating ambient temperature
–40
°C
(1) Refer to the Application and Implementation section for further information.
8.4 Thermal Information
TLV62565, TLV62566
THERMAL METRIC(1)
UNIT
DBV (5 Pins)
208.3
73.7
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
RθJC(top)
RθJB
36.1
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
2.3
ψJB
35.3
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
8.5 Electrical Characteristics
Over recommended free-air temperature range, VIN = 3.6 V, TA = -40°C to 85°C, typical values are at TA = 25°C (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
SUPPLY
VIN
IQ
Input voltage
2.7
5.5
2.3
V
uA
V
Quiescent current into VIN pin
Under voltage lock out
IOUT = 0 mA, Not switching
50
2.2
200
150
20
VIN falling
VUVLO
Under voltage lock out hysteresis
Thermal shutdown
mV
Junction temperature rising
TJSD
°C
Thermal shutdown hysteresis
Junction temperature falling below TJSD
LOGIC INTERFACE, TLV62565
VIH
High-level input voltage
Low-level input voltage
Shutdown current into VIN pin
EN leakage current
2.7 V ≤ VIN ≤ 5.5 V
2.7 V ≤ VIN ≤ 5.5 V
EN = LOW
1.2
V
V
VIL
0.4
1
ISD
0.1
µA
µA
IEN,LKG
0.01
0.16
POWER GOOD, TLV62566
Power Good low threshold
VFB falling referenced to VFB nominal
VFB risng referenced to VFB nominal
Isink = 500 µA
90%
95%
VPG
Power Good high threshold
Low level voltage
VL
0.4
V
IPG,LKG
OUTPUT
VOUT
PG Leakage current
VPG = 5.0 V
0.01
0.17
µA
Output voltage
0.6
0.588
0.594
DMAX.VIN
0.612
V
V
V
PWM operation, TA = -40°C to 85°C
PWM operation, TA = 85°C
PFM comparator threshold
VFB = 0.6 V
0.6
0.6
VFB
Feedback regulation voltage
0.606
0.9%
10
IFB
Feedback input bias current
High-side FET on resistance
Low-side FET on resistance
Low-side FET valley current limit
High-side FET peak current limit
Switching frequency
100
nA
ISW = 500 mA, VIN = 3.6 V
ISW = 500 mA, VIN = 3.6 V
173
105
RDS(on)
mΩ
ILIM,LS
ILIM,HS
fSW
1.5
1.8
A
A
1.5
95%
40
MHz
DMAX
tOFF,MIN
Maximum duty cycle
Minimum off time
ns
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
8.6 Typical Characteristics
Table 1. Table of Graphs
FIGURE
vs Load current (VOUT = 1.8 V, VIN = 2.7 V, 3.6 V, 5.5 V)
vs Load current (VOUT = 1.2 V, VIN = 2.7 V, 3.6 V, 5.5 V)
vs Load current (VOUT = 3.3 V, VIN = 4.2 V, 5.5 V)
vs Input voltage (Line regulation, VOUT = 1.8 V, Load = 0.5 A,1 A,1.5 A)
vs Load current (Load regulation, VOUT = 1.8 V, VIN = 2.7 V, 3.6 V, 5.5 V)
vs Input voltage
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Efficiency
Output voltage
Quiescent current
RDS(on)
vs Input voltage, High-Side FET
vs Input voltage, Low-Side FET
Switching frequency vs Load current, VOUT = 1.8 V
6
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VOUT=1. 8V
VOUT=1.2V
VIN=2.7V
VIN=2.7V
V
=3.6V
V
=3.6V
IN
IN
V
=5.5V
V
=5.5V
IN
IN
10µ
10µ
10µ
100µ
1m
10m
100m
1
10µ
2.5
2.5
100µ
1m
10m
100m
1
C001
C003
C004
C002
Load current [A]
Load current [A]
Figure 1. Efficiency vs Load Current
Figure 2. Efficiency vs Load Current
100
90
80
70
60
50
40
30
20
10
0
1.85
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
1.75
Load=0.5A
VOUT=3.3V
Load=1A
Load=1.5A
VIN=4.2V
V
=5.5V
IN
3
3.5
4
4.5
5
5.5
6
100µ
1m
10m
100m
1
C011
Load current [A]
Input Voltage[V]
Figure 3. Efficiency vs Load Current
Figure 4. Output Voltage vs Input Voltage
1.85
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
1.75
100
90
80
70
60
50
40
30
20
10
VOUT = 0.6V
VIN=2.7V
TA=±40°C
V
=3.6V
TA=25°C
IN
V
=5.5V
IN
TA=85°C
3.0
3.5
4.0
4.5
5.0
5.5
6.0
100µ
1m
10m
100m
1
C009
Load current [A]
Input Voltage [V]
Figure 5. Output Voltage vs Load Current
Figure 6. Quiescent Current vs Input Voltage
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
300
TA=±40°C
TA=±40°C
190
170
150
130
110
90
Load = 0.5A
Load = 0.5A
280
T=25°C
T =25°C
A
A
260
240
220
200
180
160
140
120
100
T =85°C
A
T =85°C
A
70
50
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
C007
C008
Input Voltage [V]
Input Voltage [V]
Figure 7. High-Side FET RDS(on) vs Input Voltage
Figure 8. Low-Side FET RDS(on) vs Input Voltage
1,600
VOUT = 1.8V
1,500
1,400
1,300
1,200
1,100
1,000
VIN=2.7V
V=3.6V
IN
V
=5.5V
IN
0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
C010
Load Current [A]
Figure 9. Switching Frequency vs Load Current
9 Parameter Measurement Information
L1
2.2µH
VOUT
VIN
VIN
EN
SW
FB
2.7V to 5.5V
R1
R2
C2
10µF
C1
4.7µF
GND
TLV62565
Table 2. List of Components
REFERENCE
DESCRIPTION
MANUFACTURER
C1
C2
4.7 µF, Ceramic Capacitor, 6.3 V, X5R, size 0603, GRM188R60J475ME84
10 µF, Ceramic Capacitor, 6.3 V, X5R, size 0603, GRM188R60J106ME84
2.2 µH, Power Inductor, 2.5 A, size 4mmx4mm, LQH44PN2R2MP0
Chip resistor,1%,size 0603
Murata
Murata
Murata
Std.
L1
R1,R2
8
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
10 Detailed Description
10.1 Overview
The TLV62565/6 device family includes two high-efficiency synchronous step-down converters. Each device
operates with an adaptive on-time control scheme, which is able to dynamically adjust the on-time duration
based on the input voltage and output voltage so that it can achieve relative constant frequency operation. The
device operates at typically 1.5-MHz frequency pulse width modulation (PWM) at moderate to heavy load
currents. Based on the VIN/VOUT ratio, a simple circuit sets the required on time for the high-side MOSFET. It
makes the switching frequency relatively constant regardless of the variation of input voltage, output voltage, and
load current. At the beginning of each switching cycle, the high-side switch is turned on and the inductor current
ramps up to a peak current that is defined by on time and inductance. In the second phase, once the on time
expires, the high-side switch is turned off while the low-side switch is being turned on. The current through the
inductor then decays until triggering the valley current limit determined by the output of the error amplifier. Once
this occurs, the on timer is set to turn the high-side switch back on again and the cycle is repeated.
The TLV62565/6 device family offers excellent load transient response with a unique fast response constant on-
time valley current mode. The switching frequency changes during load transition so that the output voltage
comes back in regulation faster than a traditional fixed PWM control scheme. Figure 10 shows the operation
principles of the load transient response of the TLV62565/6. Internal loop compensation is integrated which
simplifies the design process while minimizing the number of external components. At light load currents the
device automatically operates in Power Save Mode with pulse frequency modulation (PFM).
Load step up
Load step down
LS FET
current
Valley current
PWM
<fsw1
fsw1
>fsw1
Figure 10. Operation in Load Transient
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
10.2 Functional Block Diagrams
VIN
Soft
start
Thermal
Shutdown
UVLO
Current Limit
Detect
PMOS
Control Logic
EN
FB
DBG
Gate Drive
SW
NMOS
_
Pulse
Modulator
GM
DBG
+
Vref
SW
Valley
Current
Detect
Duty Detect
GND
Figure 11. TLV62565 Functional Block Diagram
VIN
PG
Soft
start
Thermal
UVLO
Shutdown
Current Limit
Detect
PMOS
Control Logic
DBG
Gate Drive
SW
NMOS
_
FB
Pulse
Modulator
GM
+
DBG
Vref
SW
Valley
Current
Detect
Duty Detect
GND
Figure 12. TLV62566 Functional Block Diagram
10
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
10.3 Feature Description
10.3.1 Power Save Mode
The device integrates a Power Save Mode with PFM to improve efficiency at light load. In Power Save Mode, the
device only switches when the output voltage trips below a set threshold voltage. It ramps up the output voltage
with several pulses and stops switching when the output voltage is higher than the set threshold voltage. PFM is
exited and PWM mode entered in case the output current can no longer be supported in Power Save Mode. The
threshold of the PFM comparator is typically 0.9% higher than the normal reference voltage. Figure 13 shows the
details of PFM/PWM mode transition.
Output
Voltage
PFM mode at light load
VPFM_Threshold
PWM mode at medium / heavy load
VOUT_NOM
t
Figure 13. Output Voltage in PFM/PWM Mode
10.3.2 Enabling/Disabling the Device
The device is enabled by setting the EN input to a logic HIGH. Accordingly, a logic LOW disables the device. If
the device is enabled, the internal power stage starts switching and regulates the output voltage to the set point
voltage. The EN input must be terminated and should not be left floating.
10.3.3 Soft Start
After enabling the device, internal soft-start circuitry monotonically ramps up the output voltage which reaches
nominal output voltage during a soft-start time of 250 µs (typical). This avoids excessive inrush current and
creates a smooth output voltage rise slope. It also prevents excessive voltage drops of primary cells and
rechargeable batteries with high internal impedance.
If the output voltage is not reached within the soft-start time, such as in the case of a heavy load, the converter
enters regular operation. The TLV62565/6 are able to start into a pre-biased output capacitor. The converter
starts with the applied bias voltage and ramps the output voltage to its nominal value.
10.3.4 Switch Current Limit
The switch current limit prevents the device from high inductor current and drawing excessive current from a
battery or input voltage rail. Excessive current might occur with a heavy load or shorted output circuit condition.
The TLV62565/6 adopt valley current control by sensing the current of the low-side MOSFET. Once the low-side
valley switch current limit is tripped, the low-side MOSFET is turned off and limits the inductor's valley current.
The high-side current is also limited which is determined by the on time of the high-side MOSFET and inductor
value calculated by Equation 1. For example, with 3.6 VIN to 1.8 VOUT and 2.2-µH specification, the peak current
limit is approximately 1.97 A with a typical valley current limit of 1.7 A.
Additionally, there is a secondary high-side current limit (typical 2 A) to prevent the current from going too high,
which is shown in Figure 14. Due to the internal propagation delay, the real current limit value might be higher
than the static current limit in the electrical characteristics table.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
Feature Description (continued)
Inductor
Current
Secondary current limit
Peak current limit
Maximum load current
Valley current limit
t
Figure 14. Switch Current Limit
IPEAK,LIMIT = IVALLEY,LIM IT + ΔIL
VOUT (1- D)
´
ΔIL =
L
fSW
where:
•
•
IPEAK,LIMIT is the high-side peak current limit
IVALLEY,LIMIT is the low-side valley current limit
(1)
10.3.5 Power Good
The TLV62566 integrates a Power Good output going low when the output voltage is below its nominal value.
The Power Good output stays high impedance once the output is above 95% of the regulated voltage and is low
once the output voltage falls below typically 90% of the regulated voltage. The PG pin is an open drain output
and is specified to sink typically up to 0.5 mA. The Power Good output requires a pull-up resistor connected to
any voltage lower than 5.5 V. When the device is off due to UVLO or thermal shutdown, the PG pin is pulled to
logic low.
10.4 Device Functional Modes
10.4.1 Under Voltage Lockout
To avoid mis-operation of the device at low input voltages, under voltage lockout is implemented that shuts down
the device at voltages lower than VUVLO with VHYS_UVLO hysteresis.
10.4.2 Thermal Shutdown
The device enters thermal shutdown once the junction temperature exceeds typically TJSD. Once the device
temperature falls below the threshold with hysteresis, the device returns to normal operation automatically.
Power Good is pulled low when thermal protection is triggered.
12
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
11 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
11.1 Application Information
The TLV6256x devices are synchronous step-down converters optimized for small solution size and high
efficiency. The devices integrate switches capable of delivering an output current up to 1.5 A.
11.2 Typical Application
TLV62565 2.7-V to 5.5-V input, 1.2-V output converter.
L1
2.2µH
VOUT
1.2V
VIN
VIN
EN
SW
FB
2.7V to 5.5V
R1
120k
C2
10µF
C1
4.7µF
GND
R2
120k
TLV62565
Figure 15. TLV62565 1.2-V Output Application
11.2.1 Design Requirements
11.2.1.1 Output Filter Design
The inductor and output capacitor together provide a low-pass frequency filter. To simplify this process, Table 3
outlines possible inductor and capacitor value combinations.
Table 3. Matrix of Output Capacitor and Inductor Combinations
COUT [µF](2) (3)
L [µH](1)
4.7
10
22
47
100
1
(4)
(4)
(4)
2.2
4.7
+
+
+
(1) Inductor tolerance and current de-rating is anticipated. The effective inductance can vary by +20% and
-30%.
(2) Capacitance tolerance and bias voltage de-rating is anticipated. The effective capacitance can vary by
+20% and -50%.
(3) For low output voltage applications (≤ 1.2 V), more output capacitance is recommended (usually ≥ 22
µF) for smaller ripple.
(4) Typical application configuration. '+' indicates recommended filter combinations.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
11.2.1.2 Inductor Selection
The main parameters for inductor selection is inductor value and then saturation current of the inductor. To
calculate the maximum inductor current under static load conditions, Equation 2 is given:
DIL
IL,MAX = IOUT,MAX
+
2
VOUT
1-
V
IN
DIL = VOUT
´
L ´ fSW
where:
•
•
•
•
IOUT,MAX is the maximum output current
ΔIL is the inductor current ripple
fSW is the switching frequency
L is the inductor value
(2)
It is recommended to choose a saturation current for the inductor that is approximately 20% to 30% higher than
IL,MAX. In addition, DC resistance and size should also be taken into account when selecting an appropriate
inductor. The recommended inductors are listed in Table 4.
Table 4. List of Recommended Inductors
INDUCTANCE
[µH]
CURRENT RATING
[mA]
DIMENSIONS
DC RESISTANCE
TYPE
MANUFACTURER
L x W x H [mm3]
[mΩ typ]
2.2
2.2
2500
3000
4 x 3.7 x 1.65
4 x 4 x 1.8
49
50
LQH44PN2R2MP0
Murata
NRS4018T2R2MDGJ
Taiyo Yuden
11.2.1.3 Input and Output Capacitor Selection
The input capacitor is the low impedance energy source for the converter that helps provide stable operation.
The closer the input capacitor is placed to the VIN and GND pins, the lower the switch ring. A low ESR multilayer
ceramic capacitor is recommended for best filtering. For most applications, 4.7-µF input capacitance is sufficient;
a larger value reduces input voltage ripple.
The architecture of the TLV62565/6 allow use of tiny ceramic-type output capacitors with low equivalent series
resistance (ESR). These capacitors provide low output voltage ripple and are thus recommended. To keep its
resistance up to high frequencies and to achieve narrow capacitance variation with temperature, it is
recommended to use X7R or X5R dielectric. The TLV62565/6 are designed to operate with an output
capacitance of 10 µF to 47 µF, as outlined in Table 3.
14
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
11.2.2 Detailed Design Procedure
11.2.2.1 Setting the Output Voltage
An external resistor divider is used to set output voltage. By selecting R1 and R2, the output voltage is
programmed to the desired value. When the output voltage is regulated, the typical voltage at the FB pin is VFB
.
Equation 3, Equation 4, and Equation 5 can be used to calculate R1 and R2.
When sizing R2, in order to achieve low quiescent current and acceptable noise sensitivity, use a minimum of 5
μA for the feedback current IFB. Larger currents through R2 improve noise sensitivity and output voltage accuracy
but increase current consumption.
R1
R2
R1
R2
æ
ö
÷
ø
æ
ö
÷
ø
VOUT = VFB ´ 1+
= 0.6V ´ 1+
ç
ç
è
è
(3)
(4)
(5)
VFB 0.6V
=
IFB 5mA
R2 =
=120kW
VOUT
VOUT
R1= R2´(
-1) = R2´(
-1)
VFB
0.6V
11.2.2.2 Loop Stability
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signals:
•
•
•
Switching node, SW
Inductor current, IL
Output ripple voltage, VOUT(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations, the
regulation loop may be unstable. This is often a result of board layout and/or L-C combination. Applications with
the recommended L-C combinations in Table 3 are designed for good loop stability as well as fast load transient
response.
As a next step in the evaluation of the regulation loop, the load transient response is illustrated. The TLV62565/6
use a constant on time with valley current mode control, so the on time of the high-side MOSFET is relatively
consistent from cycle to cycle when a load transient occurs. Whereas the off time adjusts dynamically in
accordance with the instantaneous load change and brings VOUT back to the regulated value.
During recovery time, VOUT can be monitored for settling time, overshoot, or ringing which helps judge the
stability of the converter. Without any ringing, the loop usually has more than 45° of phase margin.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
11.2.3 Application Performance Curves
VIN = 3.6 V
VO = 1.8 V/100mA
VIN = 3.6 V
VO = 1.8 V
Vo
Vo
20 mV/div
10 mV/div
SW
2 V/div
SW
2 V/div
Iinductor
1A/div
Iinductor
1A/div
G001
G002
0.4 µs/div
2.0 µs/div
Figure 16. Typical Application (PWM Mode)
Figure 17. Typical Application (PFM Mode)
VIN = 3.6 V
VO = 1.8 V/10mA
Vo
Vo
20 mV/div
0.1 V/div
Io
SW
2 V/div
1 A/div
Iinductor
1 A/div
VIN = 3.6 V
VO = 1.8 V
Iinductor
1A/div
L=2.2 uH,Co=10 uF
Load: 0.3 A to 1.3 A
G003
G007
10 µs/div
4.0 µs/div
Figure 18. Typical Application (PFM Mode)
Figure 19. Load Transient
VIN = 3.6 V
VO = 1.8 V
VIN = 3.6 V
VO = 1.8 V
L=2.2 uH, Co=10 uF
Load: 1.3 A to 0.3 A
Vo
0.1 V/div
Vo
1 V/div
Io
1 A/div
EN
2 V/div
Iinductor
1 A/div
Iinductor
1A/div
G008
G004
4.0 µs/div
400 µs/div
Figure 20. Load Transient
Figure 21. Start Up
16
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
VIN = 3.6 V
VO = 1.8 V
VIN = 3.6 V
VO = 1.8 V
Load= 0 A
Vo
1 V/div
Vo
1 V/div
PG
1 V/div
Io
VIN
1 A/div
5 V/div
Iinductor
1A/div
Iinductor
1 A/div
G005
G006
400 µs/div
2.0 µs/div
Figure 22. Start Up (Power Good)
Figure 23. Short Circuit Protection
12 Power Supply Recommendations
The power supply to the TLV62565 and TLV62566 needs to have a current rating according to the supply
voltage, output voltage and output current of the TLV62565 and TLV62566.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
13 Layout
13.1 Layout Guidelines
The PCB layout is an important step to maintain the high performance of the TLV62565 devices.
•
•
The input/output capacitors and the inductor should be placed as close as possible to the IC.
This keeps the traces short. Routing these traces direct and wide results in low trace resistance and low
parasitic inductance.
•
•
A common power GND should be used.
The low side of the input and output capacitors must be connected properly to the power GND to avoid a
GND potential shift.
•
•
The sense traces connected to FB is a signal trace .
Special care should be taken to avoid noise being induced. By a direct routing, parasitic inductance can be
kept small.
•
•
GND layers might be used for shielding.
Keep these traces away from SW nodes.
13.2 Layout Example
Top layer
L
Bottom layer
VIN
VOUT
SW
COUT
CIN
D
GN
GND
EN
/PG
FB
R3
GND
R1
Note: PG connected to VIN via R3, EN direct connect to VIN
Figure 24. TLV62565 Layout
13.3 Thermal Considerations
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow,
convection surfaces, and the presence of other heat-generating components affect the power dissipation limits of
a given component.
Two basic approaches for enhancing thermal performance are listed below:
•
•
Improving the power dissipation capability of the PCB design
Introducing airflow in the system
For more details on how to use the thermal parameters, see the application notes: Thermal Characteristics
Application Notes SZZA017 and SPRA953.
18
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
www.ti.com
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
14 Device and Documentation Support
14.1 Device Support
14.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
14.2 Documentation Support
14.2.1 Related Documentation
Semiconductor and IC Package Thermal Metrics Application Report (SPRA953)
Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs Application Report
(SZZA017)
14.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TLV62565
TLV62566
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
14.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
14.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
14.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
14.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2013–2015, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: TLV62565 TLV62566
TLV62565, TLV62566
SLVSBC1C –OCTOBER 2013–REVISED JULY 2015
www.ti.com
15 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
20
Submit Documentation Feedback
Copyright © 2013–2015, Texas Instruments Incorporated
Product Folder Links: TLV62565 TLV62566
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jul-2015
PACKAGING INFORMATION
Orderable Device
TLV62565DBVR
TLV62565DBVT
TLV62566DBVR
TLV62566DBVT
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
SOT-23
SOT-23
SOT-23
SOT-23
DBV
5
5
5
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
SIK
SIK
SIL
SIL
ACTIVE
ACTIVE
ACTIVE
DBV
DBV
DBV
250
3000
250
Green (RoHS
& no Sb/Br)
-40 to 85
Green (RoHS
& no Sb/Br)
-40 to 85
Green (RoHS
& no Sb/Br)
-40 to 85
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jul-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jul-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLV62565DBVR
TLV62565DBVT
TLV62566DBVR
TLV62566DBVT
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
5
5
5
5
3000
250
178.0
178.0
178.0
178.0
9.0
9.0
9.0
9.0
3.23
3.23
3.23
3.23
3.17
3.17
3.17
3.17
1.37
1.37
1.37
1.37
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jul-2015
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLV62565DBVR
TLV62565DBVT
TLV62566DBVR
TLV62566DBVT
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
5
5
5
5
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
18.0
18.0
18.0
18.0
3000
250
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明