TLV803EA22DBZR [TI]
TLV803E, TLV809E, TLV810E Low Power 250-nA IQ and Small Size Supply Voltage Supervisors;型号: | TLV803EA22DBZR |
厂家: | TEXAS INSTRUMENTS |
描述: | TLV803E, TLV809E, TLV810E Low Power 250-nA IQ and Small Size Supply Voltage Supervisors |
文件: | 总44页 (文件大小:2122K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
TLV803E, TLV809E, TLV810E Low Power 250-nA IQ and Small Size Supply Voltage
Supervisors
1 Features
3 Description
The TLV803E, TLV809E, and TLV810E are
enhanced alternatives to the TLV803, TLV853,
TLV809, LM809, TPS3809 and TLV810. TLV803E,
TLV809E and TLV810E offer lower supply current for
battery-powered applications, higher accuracy, wider
1
•
Ensured RESET/RESET for VDD = 0.7 V to 6 V
•
Fixed time delay: 40 µs, 10 ms, 50 ms, 100 ms,
200 ms, 400 ms
•
Supply current (IDD): 250 nA (typical)
temperature range, and lower power-on-reset (VPOR
for increased system reliability.
)
–
1 µA (maximum for VDD = 3.3 V)
•
•
Output topology:
The TLV803E, TLV809E, and TLV810E family are
low IQ (250 nA typical, 1 µA max), voltage supervisory
circuits (reset IC) that monitor VDD voltage level.
These devices initiate a reset signal whenever supply
voltage VDD drops below the factory programmed
falling threshold voltage, VIT–. The reset output
remains low for a fixed reset time delay tD after the
VDD voltage rises above the rising voltage threshold
(VIT+) which is equivalent to the falling threshold
voltage (VIT-) plus hysteresis (VHYS).
–
–
–
TLV809E: push-pull, active-low
TLV803E: open-drain, active-low
TLV810E: push-pull, active-high
Under voltage detection:
–
–
–
High accuracy: ±0.5% (typical)
Nominal voltage monitor: 3 V, 3.3 V, 5 V
(VIT–): 1.7 V, 1.8 V, 1.9 V, 2.4 V, 2.64 V,
2.93 V, 3.08 V, 4.38 V, 4.63 V
•
Package:
These devices have integrated glitch immunity to
ignore fast transients on the VDD pin. The low current
consumption and high accuracy (±0.5% typical)
makes these voltage supervisors ideal for use in low-
power and portable applications. The TLV80xE and
TLV81xE devices are specified to have the defined
–
–
–
–
SOT23-3 (DBZ) (with pin 1 = GND)
SOT23-3 (DBZ) (with pin 1 = RESET/RESET)
SC-70 (DCK)
X2SON-5 (DPW)
output logic state for supply voltages down to VPOR
=
•
•
Temperature range: –40°C to +125°C
0.7 V. The TLV80xE and TLV81xE devices are
available in industry standard 3-pin SOT23 (DBZ)
package, 3-pin SC70 (DCK) package, and very
compact X2SON (DPW) package.
Pin-to-pin compatible with MAX803/809/810,
APX803/809/810
2 Applications
Device Information(1)
•
Applications using DSPs, microcontrollers, or
microprocessors
PART NUMBER
PACKAGE
BODY SIZE (NOM)
2.90 mm × 1.30 mm
2.00 mm × 1.25 mm
0.8 mm x 0.8 mm
SOT-23 (3)
•
•
•
•
•
Electricity meters
TLV803E, TLV809E,
TLV810E
SC-70 (3)
Portable, battery-powered equipment
Set-top boxes and TVs
X2SON (5)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Building automation
Notebook/desktop computers, servers
Typical Application
LDO
IN
OUT
VDD
*Rpull-up
FPGA, ASIC, DSP
VDD
RESET
TLV803E
RESET
GND
GND
*Pull-up resistor not required for TLV809E, TLV810E
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
Table of Contents
8.4 Device Functional Modes........................................ 16
Application and Implementation ........................ 18
9.1 Application Information............................................ 18
9.2 Typical Application ................................................. 18
9.3 Typical Application .................................................. 20
1
2
3
4
5
6
7
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Device Comparison ............................................... 3
Pin Configuration and Functions......................... 4
Specifications......................................................... 5
7.1 Absolute Maximum Ratings ...................................... 5
7.2 ESD Ratings.............................................................. 5
7.3 Recommended Operating Conditions....................... 5
7.4 Thermal Information.................................................. 5
7.5 Electrical Characteristics........................................... 6
7.6 Timing Requirements................................................ 7
7.7 Timing Diagram......................................................... 8
7.8 Typical Characteristics.............................................. 9
Detailed Description ............................................ 14
8.1 Overview ................................................................. 14
8.2 Functional Block Diagram ....................................... 14
8.3 Feature Description................................................. 14
9
10 Power Supply Recommendations ..................... 21
11 Layout................................................................... 21
11.1 Layout Guidelines ................................................. 21
11.2 Layout Example .................................................... 21
12 Device and Documentation Support ................. 22
12.1 Device Support .................................................... 22
12.2 Documentation Support ....................................... 23
12.3 Related Links ........................................................ 23
12.4 Receiving Notification of Documentation Updates 23
12.5 Support Resources ............................................... 23
12.6 Trademarks........................................................... 23
12.7 Electrostatic Discharge Caution............................ 23
12.8 Glossary................................................................ 23
8
13 Mechanical, Packaging, and Orderable
Information ........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (April 2020) to Revision F
Page
•
•
Changed DPW package from Advanced Information to Production Data.............................................................................. 1
Changed DPW package Information ..................................................................................................................................... 4
Changes from Revision D (February 2020) to Revision E
Page
•
Added X2SON (DPW) package option .................................................................................................................................. 3
Changes from Revision C (November 2019) to Revision D
Page
•
•
•
•
•
Added device nomenclature figure ........................................................................................................................................ 3
Added timing diagram for TLV810E ...................................................................................................................................... 8
Added Figure 6, Figure 23, Figure 24 ................................................................................................................................... 9
Changed block diagram and description to include TLV810E.............................................................................................. 14
Added typical application for TLV810E ............................................................................................................................... 20
Changes from Revision B (July 2019) to Revision C
Page
•
Changed device status from Advance Information to Production Data.................................................................................. 1
2
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
5 Device Comparison
Figure 1 shows the device naming nomenclature to compare the difference device variants. See for a more
detailed explanation.
TLV XXXX X XX X XXX
Package
DBZ: SOT23
DCK: SC70
DPW: X2SON
Reverse Pinout Indicator
R: Pin 1 = RESET, Pin 2 = GND
Threshold Voltage
17: 1.7 V
...
Output Type
Delay Option
A: 200 ms
B: 40 µs
803E: Open-Drain Active-Low
809E: Push-Pull Active-Low
810E: Push-Pull Active-High
46: 4.63 V
C: 10 ms
D: 50 ms
E: 100 ms
F: 400 ms
Figure 1. Device Naming Nomenclature
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
6 Pin Configuration and Functions
DBZ Package (Pin 1 = GND)
3-Pin SOT-23
DBZ Package (Pin 1 = RESET, reverse pinout)
3-Pin SOT-23
Top View
Top View
GND
1
RESET
GND
1
VDD
3
VDD
3
RESET
2
2
RESET
(TLV810E)
DPW Package
4-Pin X2SON
Top View
DCK Package
3-Pin SC-70
Top View
RESET
VDD
GND
4
1
GND
1
RESET
(TLV810E)
VDD
3
PAD
RESET
2
MR
2
3
Top View
Pin Functions
PIN
DBZ
(REVERSE
PINOUT)
I/O
DESCRIPTION
NAME
DCK, DBZ
DPW
GND
1
2
3
—
O
Ground
Active-low output reset signal: This pin is driven low logic
when VDD voltage falls below the negative voltage threshold
(VIT–). RESET remains low (asserted) for the delay time period
(tD) after VDD voltage rise above VIT+.
RESET
2
1
1
Active-High output reset signal (TLV810E only): This pin is
driven high logic when VDD voltage falls below the negative
voltage threshold (VIT–). RESET remains high (asserted) for the
delay time period (tD) after VDD voltage rise above VIT+.
RESET
VDD
2
3
1
3
1
4
O
I
Input supply voltage. TLV803E, TLV809E, TLV810E monitor
VDD voltage.
Active-low manual reset input. Pull this pin to a logic low
(VMR_L) to assert a reset signal in the output pin. After the MR
pin is left floating or pulled to VMR_H the output goes to the
nominal state after the reset delay time (tD) expires. MR can be
left floating when not in use.
MR
N/A
N/A
N/A
N/A
2
I
No Connection. Thermal pad helps with thermal dissipation.
Connection not required.
PAD
PAD
—
4
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range, unless otherwise noted(1)
MIN
MAX
UNIT
V
VDD pin
–0.3
6.5
(2)
Voltage
RESET (TLV809E), RESET (TLV810E)
RESET (TLV803E)
–0.3 VDD + 0.3
V
–0.3
–0.3
-20
6.5
VDD + 0.3(2)
V
Voltage
Current
MR
V
Output sink and source current
Operating ambient, TA
Storage, Tstg
20
125
150
mA
–40
–65
Temperature(3)
°C
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Condition. Exposure to absolute-maximum-rated conditions (above the Recommended Operating Conditions) for extended
periods may affect device reliability.
(2) The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller.
(3) As a result of the low dissipated power in this device, the junction temperature is assumed to be equal to the ambient temperature.
7.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-
001(1)
± 2000
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per JEDEC specification
JESD22-C101(2)
± 500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
1.7
0
NOM
MAX
6
UNIT
V
VDD
Input supply voltage
VRESET, VRESET
RESET pin and RESET pin voltage
RESET pin and RESET pin current
Junction temperature (free air temperature)
Manual reset pin voltage
6
V
IRESET, IRESET
0
±5
mA
°C
V
TJ
–40
0
125
VDD
VMR
7.4 Thermal Information
TLV803E, TLV809E, TLV810E
THERMAL METRIC(1)
DPW (X2SON)
5 PINS
457.1
DCK (SC70-3)
3 PINS
300.5
DBZ (SOT23-3)
3 PINS
254.8
UNIT
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
201.6
178.2
150.5
320.4
166.5
140.1
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
22.8
70
48.1
ψJB
318.8
165.2
139.1
RθJC(bot)
N/A
N/A
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
7.5 Electrical Characteristics
over operating range (TA = –40℃ to 125℃), 1.7 V ≤ VDD ≤ 6 V, RUP = 10 kΩ to 6 V, 10 pF load at RESET pin, unless
otherwise noted. Typical values are at 25℃, VDD = 3.3V and VIT– = 2.93 V.
PARAMETER
COMMON PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX UNIT
VDD
VIT–
VHYS
Input supply voltage
1.7
–2
6
2
V
%
Input threshold voltage accuracy
Hysteresis voltage
TA= –40℃ to 125℃
0.5
1.2
Hysteresis from VIT–
VDD = 3.3 V; VDD > VIT+
VDD = 6 V
0.9
1.5
1
%
(1)
0.25
0.4
µA
µA
IDD
Supply current into VDD pin
1.2
Manual reset pin internal pull-up
resistance
RMR
100
kΩ
X2SON (DPW) package only
VMR_L
VMR_H
Manual reset pin logic low input
Manual reset pin logic high input
0.4
V
V
0.8VDD
TLV809E (Push-Pull Active-Low)
(2)
VPOR
Power on reset voltage
VOL ≤ 300 mV, IOUT(Sink) = 15 µA
700
300
300
mV
mV
mV
V
VDD = 1.7 V, VDD < VIT–, IOUT(Sink) = 500 µA
VDD = 3.3 V, VDD < VIT–, IOUT(Sink) = 2 mA
VDD = 6 V, VDD > VIT+, IOUT(Source) = 4 mA
VDD = 3.3 V, VDD > VIT+, IOUT(Source) = 2 mA
Low level output voltage
High level output voltage
VOL
0.8VDD
0.8VDD
VOH
V
TLV803E (Open-Drain Active-Low)
(2)
VPOR
Power on reset voltage
Low level output voltage
V
OL ≤ 300 mV, IOUT(Sink) = 15 µA
700
300
300
350
mV
mV
mV
nA
VDD = 1.7 V, VDD < VIT–, IOUT(Sink) = 500 µA
VDD = 3.3 V, VDD < VIT–, IOUT(Sink) = 2 mA
VDD = VPULLUP = 6 V, VDD > VIT+
VOL
Ilkg(OD)
Open drain output leakage current
100
TLV810E (Push-Pull Active-High)
VDD = 3.3 V, VDD < VIT–, IOUT(Source) = 2 mA
VDD = 1.7 V, VDD < VIT–, IOUT(Source) = 500 µA
VOH ≥ 720 mV, IOUT(Source) = 15 µA
0.8VDD
0.8VDD
V
High level output voltage
VOH
V
VPOR
VOL
Power on Reset Voltage
Low level output voltage
900
300
300
mV
mV
mV
VDD = 6 V, VDD > VIT+, IOUT(Sink) = 2 mA
VDD = 3.3 V, VDD > VIT+, IOUT(Sink) = 500 µA
(1) VIT+ = VIT– + VHYS
(2) Minimum VDD voltage for a controlled output state. Below VPOR, the output cannot be determined.
6
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
7.6 Timing Requirements
over operating range (TA = –40℃ to 125℃), 1.7 V ≤ VDD ≤ 6 V, RUP = 10 kΩ to 6 V (Open Drain only), 10 pF load at RESET
pin, Overdrive = 10%, unless otherwise noted. Typical values are at 25℃, VDD = 3.3 V and VIT– = 2.93 V.
PARAMETER
Glitch immunity
TEST CONDITIONS
5 % Overdrive(1)
MIN
TYP
MAX
UNIT
tGI
10
µs
Propagation delay from VDD falling below
VIT– to RESET
VDD = (VIT+ + 30%) to (VIT–
10%)
–
tPD_HL
30
50
µs
(2)
Reset time delay variant A
130
200
270
ms
(2)
Reset time delay variant B
;
RUP = 100 kΩ, CL = 100 pF, 30%
Overdrive
45
90
µs
(3)
tD
Release time or reset timeout period
(2)
Reset time delay variant B
40
10
80
µs
(2)
Reset time delay variant C
6.5
13.5
ms
MR pin pulse duration to initiate RESET,
RESET
tMR_PW
tMR_RES
tMR_tD
500
700
ns
ns
Propagation delay from MR low to RESET,
RESET
VDD = 4.5 V, VMR : VMR_H to
VMR_L
Delay from release MR to deasert RESET,
RESET
VDD = 4.5 V, VMR : VMR_L to
VMR_H
tD_MIN
tD_TYP
tD_MAX
ms
(1) Overdrive = [(VDD/ VIT–) - 1] × 100%. Refer to Section 8.3.3 on VDD glitch immunity.
(2) Refer to device nomenclature table in Section 12.1.1. VDD: (VIT--10%) to (VIT+ + 10%)
(3) Specified by design
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
7.7 Timing Diagram
VIT+
VIT-
VHYS
VDD(MIN)
VPOR
VDD
tPD_HL
tPD_HL
tD
RESET
Undefined output VDD < VPOR
Diagram not to scale
Figure 2. TLV803E, TLV809E Timing Diagram
VIT+
VIT-
VHYS
VDD(MIN)
VPOR
VDD
tPD_HL
tPD_HL
tD
tD
RESET
Undefined output VDD < VPOR
Diagram not to scale
Figure 3. TLV810E Timing Diagram
8
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
7.8 Typical Characteristics
Typical characteristics show the typical performance of the TLV803E, TLV809E, and TLV810E devices. Test conditions are
TA = 25°C, VDD = 3.3 V, VIT- = 2.93 V, Rpull-up = 10 kΩ to 6 V, CLoad = 50 pF, unless otherwise noted.
0.45
0.4
0.5
0.45
0.4
25°C
-40°C
125°C
25°C
-40°C
125°C
0.35
0.3
0.35
0.3
0.25
0.2
0.25
0.2
0.15
0.1
0.15
0.1
1.5
2
2.5
3
3.5 4
VDD (V)
4.5
5
5.5
6
1.5
2
2.5
3
3.5 4
VDD (V)
4.5
5
5.5
6
IDD_
IDD_
Figure 4. Supply Current Versus Supply Voltage for
TLV803EA29
Figure 5. Supply Current Versus Supply Voltage for
TLV809EA29
0.45
0.32
0.31
0.3
25°C
-40°C
125°C
TLV803EA29
0.4
0.35
0.3
0.29
0.28
0.27
0.26
0.25
0.24
0.23
0.22
0.21
0.2
0.25
0.2
0.15
0.1
0.05
0
1.5
2
2.5
3
3.5 4
VDD (V)
4.5
5
5.5
6
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
IDDv
IDD_
Figure 6. Supply Current Versus Supply Voltage for
TLV810EA29
Figure 7. Supply Current Over Temperature for
TLV803EA29, VDD = 3.3 V
0.32
0.31
0.3
30
27
24
21
18
15
12
9
TLV809EA29
TLV803EA29
0.29
0.28
0.27
0.26
0.25
0.24
0.23
0.22
0.21
0.2
6
3
0
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
IDD_
ILKG
Figure 9. Leakage Current Over Temperature for
TLV803EA29
Figure 8. Supply Current Over Temperature for
TLV809EA29, VDD = 3.3 V
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
Typical Characteristics (continued)
Typical characteristics show the typical performance of the TLV803E, TLV809E, and TLV810E devices. Test conditions are
TA = 25°C, VDD = 3.3 V, VIT- = 2.93 V, Rpull-up = 10 kΩ to 6 V, CLoad = 50 pF, unless otherwise noted.
1
0.92
0.84
0.76
0.68
0.6
1.3
1.2
1.1
1
TLV803EA29
TLV809EA29
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.52
0.44
0.36
0.28
0.2
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
VIT-
VIT-
Figure 10. Voltage Threshold Accuracy Over Temperature
for TLV803EA29
Figure 11. Voltage Threshold Accuracy Over Temperature
for TLV809EA29
0.8
0.55
-40°C
-20°C
-40°C
-20°C
0.5
0.72
85°C
105°C
125°C
85°C
105°C
125°C
0.45
0.4
0.64
0.56
0.48
0.4
0.35
0.3
0.25
0.2
0.32
0.24
0.16
0.08
0
0.15
0.1
0.05
0
0
0.002
0.004
0.006
0.008
0.01
0
0.002
0.004
0.006
0.008
0.01
IRESET (A)
IRESET (A)
VOLx
VOLx
Figure 12. Low Voltage Output Versus Output Current for
TLV803EA29, VDD = 1.7 V
Figure 13. Low Voltage Output Versus Output Current for
TLV809EA29, VDD = 1.7 V
25
TLV803EA29
24.5
25
TLV809EA29
24.5
24
23.5
23
24
23.5
23
22.5
22
22.5
22
21.5
21
21.5
21
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Temperature (èC)
Temperature (èC)
VOLx
VOLx
Figure 14. Low Voltage Output Over Temperature for
TLV803EA29, VDD = 1.7 V
Figure 15. Low Voltage Output Over Temperature for
TLV809EA29, VDD = 1.7 V
10
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
Typical Characteristics (continued)
Typical characteristics show the typical performance of the TLV803E, TLV809E, and TLV810E devices. Test conditions are
TA = 25°C, VDD = 3.3 V, VIT- = 2.93 V, Rpull-up = 10 kΩ to 6 V, CLoad = 50 pF, unless otherwise noted.
6
5.9
5.8
5.7
5.6
5.5
5.4
5.3
5.2
5.1
5
3.12
3.115
3.11
-40°C
-20°C
25°C
85°C
105°C
125°C
TLV809EA29
3.105
3.1
3.095
3.09
3.085
3.08
3.075
3.07
3.065
0
0.002
0.004
0.006
0.008
0.01
-40
-20
0
20
40
60
80
100 120 140
IRESET (A)
Temperature (èC)
VOHx
VOHx
Figure 16. High Voltage Output Versus Output Current for
TLV809EA29, VDD = 6 V
Figure 17. High Voltage Output Over Temperature for
TLV809EA29, VDD = 3.3 V
6
0.12
TLV803EA29
25°C
5.5
5
4.5
4
0.1
0.08
0.06
0.04
0.02
0
3.5
3
2.5
2
1.5
1
0.5
0
0
0.5
1
1.5
2
2.5
3
VDD (V)
3.5
4
4.5
5
5.5
6
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
VDD (V)
1
VCC_
Vpor
Figure 18. Reset Voltage Output Versus Voltage Input for
Figure 19. Reset Voltage Output Versus Voltage Input for
TLV803EA29, Vpull-up = VDD, Rpull-up = 10 kΩ
TLV803EA29, Rpull-up = 10 kΩ
173
2
TLV803EA29
VDD
RESET
172
171
170
169
168
167
1.6
1.2
0.8
0.4
0
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
0
6
12
18
24
30
Time (µs)
Rese
VRES
Figure 21. Reset Delay Time Over Temperature for
TLV803EA29
Figure 20. Transient Power-on-Reset Voltage for
TLV809EA30, IRESET = 15 µA
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
Typical Characteristics (continued)
Typical characteristics show the typical performance of the TLV803E, TLV809E, and TLV810E devices. Test conditions are
TA = 25°C, VDD = 3.3 V, VIT- = 2.93 V, Rpull-up = 10 kΩ to 6 V, CLoad = 50 pF, unless otherwise noted.
16.25
171.5
TLV803EB29
TLV809EA29
16.2
16.15
16.1
171
170.5
170
16.05
16
169.5
169
15.95
15.9
168.5
168
15.85
15.8
167.5
167
15.75
15.7
166.5
15.65
15.6
166
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
tD__
Rese
Figure 22. Reset Delay Time Over Temperature for
TLV809EA29
Figure 23. Reset Delay Time Over Temperature for
TLV803EB29
9
8.8
8.6
8.4
8.2
8
25
TLV803EC29
TLV803EA29
24.75
24.5
24.25
24
23.75
23.5
23.25
23
22.75
22.5
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
tPHL
Rese
Figure 25. High-to-Low Propagation Delay Over
Temperature for TLV803EA29
Figure 24. Reset Delay Time Over Temperature for
TLV803EC29
26
25.5
25
13
12
11
10
9
TLV809EA29
25°C
-40°C
125°C
24.5
24
8
7
23.5
23
6
5
22.5
22
4
3
5
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
10
15
20
25 30
Overdrive (%)
35
40
45
50
tPHL
tGI_
Figure 26. High-to-Low Propagation Delay Over
Temperature for TLV809EA29
Figure 27. Glitch Immunity Versus Overdrive for
TLV803EA29
12
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
Typical Characteristics (continued)
Typical characteristics show the typical performance of the TLV803E, TLV809E, and TLV810E devices. Test conditions are
TA = 25°C, VDD = 3.3 V, VIT- = 2.93 V, Rpull-up = 10 kΩ to 6 V, CLoad = 50 pF, unless otherwise noted.
13
25°C
-40°C
125°C
12
11
10
9
8
7
6
5
4
3
5
10
15
20
25 30
Overdrive (%)
35
40
45
50
tGI_
Figure 28. Glitch Immunity Versus Overdrive for TLV809EA29
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
8 Detailed Description
8.1 Overview
The TLV803E, TLV809E, TLV810E is a family of easy to implement low power, small size voltage supervisors
(Reset ICs) with fixed threshold voltage and fixed reset delay. The TLV803E has open-drain active-low output
topology which requires a pull-up resistor, TLV809E has push-pull active-low output topology and TLV810E has
push-pull active-high output topology. This family of devices features include integrated resistor divider threshold
with hysteresis and a glitch immunity filter.
These devices are available in SOT-23 (3) and SC70 (3) industry standard package and pinout as well as a very
small X2SON (5) package.
8.2 Functional Block Diagram
VDD
RMR
MR
Push-pull TLV809E,
DPW package only
TLV810E variants
VDD
+
VDD
RESET
LOGIC
TIMER
RESET
RESET (TLV810E)
(TLV803E, TLV809E)
œ
Reference
Voltage
GND
GND
8.3 Feature Description
8.3.1 Input Voltage (VDD)
VDD pin is monitored by the internal comparator with integrated reference to indicate when VDD falls below the
fixed threshold voltage. VDD also functions as the supply for the following:
•
•
•
•
•
Internal bandgap (reference voltage)
Internal regulator
State machine
Buffers
Other control logic blocks
Good design practice involves placing a 0.1-µF to 1-µF bypass capacitor at VDD input for noisy applications and
to ensure enough charge is available for the device to power up correctly. The reset output is undefined when
VDD is below VPOR
.
8.3.2 VDD Hysteresis
The internal comparator has built-in hysteresis to avoid erroneous output reset release. If the voltage at the VDD
pin falls below the falling voltage threshold VIT–, the output reset is asserted. When the voltage at the VDD pin
rises above the rising voltage threshold (VIT+) equivalent to VIT– plus hysteresis (VHYS), the output reset is
deasserted after tD reset time delay.
14
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
Feature Description (continued)
8.3.3 VDD Glitch Immunity
These devices are immune to quick voltage transient or excursion on VDD. Sensitivity to transients depends on
both transient duration and transient overdrive. Overdrive is defined by how much VDD exceeds the specified
threshold. Threshold overdrive is calculated as a percent of the threshold in question, as shown in Equation 1.
Overdrive = | (VDD / VIT– – 1) × 100% |
where
•
•
VIT– is the threshold voltage
VDD is the input voltage crossing VIT–
(1)
VDD
VIT+
VIT-
Overdrive
Pulse
Duration
Figure 29. Overdrive Versus Pulse Duration
TLV803E, TLV809E, and TLV810E devices have built-in glitch immunity (tGI) of 10 µs typical as shown in Timing
Requirements. Figure 30 shows that VDD must fall below VIT- for tGI, otherwise the faling transistion is ignored.
When VDD falls below VIT- for tGI, RESET transitions low to indicate a fault condition after the propagation delay
high-to-low (tPDHL). When VDD rises above VIT+, RESET only deasserts to logic high indicating there is no more
fault condition only if VDD remains above VIT+ for longer than the reset delay (tD).
VDD remains above VIT+ for only 199 ms
VDD
VIT+
VIT-
VDD drops below VIT- so
RESET transitions low after
Propagation Delay (tPDHL
)
RESET
VDD transition to above VIT+ ignored when less than
Reset Delay (tD) so RESET remains unchanged
Figure 30. Glitch Immunity when VDD Rises Above VIT+ for Less than RESET Delay (TLV803EA29)
8.3.4 Manual Reset (MR) Input for X2SON (DPW) Package Only
The manual reset (MR) input allows a processor GPIO or other logic circuits to initiate a reset. A logic low on MR
with pulse duration longer than tMR_RES will cause reset output to assert. After MR returns to a logic high (VMR_H
)
and VDD is above VIT+, reset is deasserted after the user programmed reset time delay (tD) expires.
If MR is not controlled externally, then MR can be left disconnected. If the logic signal controlling MR is less than
VDD, then additional current flows from VDD into MR internally. For minimum current consumption, drive MR to
either VDD or GND. VMR should not be higher than VDD voltage.
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
Feature Description (continued)
VDD
VIT+
VHYS
VIT-
VIT+
VHYS
VIT-
RESET
tP_HL
tD
tMR_tD
tMR_RES
MR
VMR_H
VMR_L
Reset not asserted
Pulse width less than tMR_PW
tMR_PW
Figure 31. Timing Diagram MR and RESET for X2SON (DPW) Package
8.3.5 Output Logic
8.3.5.1 RESET Output, Active-Low
RESET remains high (deasserted) as long as VDD is above the negative threshold (VIT–). If VDD falls below the
negative threshold (VIT–), then reset is asserted and RESET transistions to logic low (VOL).
When VDD rises above VIT+, the delay circuit holds RESET active and logic low for the specified reset delay
period (tD). When the reset delay has elapsed, the RESET pin transistions to high voltage (VOH).
The open-drain version requires a pull-up resistor to hold the RESET pin high because the internal MOSFET
turns off causing RESET output to pull-up to the pull-up voltage. Connect the pull-up resistor to the desired
interface voltage logic. RESET can be pulled up to any voltage up to maximum voltage independent of the VDD
voltage. To ensure proper voltage levels, take care when choosing the pull-up resistor values. The pull-up
resistor value is determined by VOL, the output capacitive loading, and the output leakage current (ILKG(OD)).
The push-pull variant does not require a pull-up resistor.
8.3.5.2 RESET Output, Active-High
RESET remains logic low (deasserted) as long as VDD is above the positive threshold (VIT+). If VDD falls below
the negative threshold (VIT–), then reset is asserted and RESET transistions to logic high (VOH).
When VDD rises above VIT+, the delay circuit holds RESET active and logic high for the specified reset delay
period (tD). When the reset delay has elapsed the RESET pin transistions to low voltage (VOL).
8.4 Device Functional Modes
summarizes the various functional modes of the device.
VDD
MR (X2SON package only)
RESET (Active-High)
RESET(Active-Low)
VDD < VPOR
N/A
N/A
L
Undefined
Undefined
VPOR < VDD < VIT–
H
H
L
L
L
V
DD ≥ VIT–
DD ≥ VIT–
V
H
H
16
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
8.4.1 Normal Operation (VDD > VDD(min)
)
When VDD voltage is greater than VDD(min), the reset signal is determined by the voltage on the VDD pin with
respect to the trip point (VIT–) and the MR pin voltage (X2SON package only).
8.4.2 VDD Between VPOR and VDD(min)
When the voltage on VDD is less than the VDD(min) voltage and greater than the power-on-reset voltage (VPOR),
the reset signal is asserted.
8.4.3 Below Power-On-Reset (VDD < VPOR
)
When the voltage on VDD is lower than VPOR, the device does not have enough bias voltage to internally pull the
asserted output low or high and reset voltage level is undefined.
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The TLV803E, TLV809E, and TLV810E devices are used for voltage monitoring. These devices have only three
pins: VDD, GND, and RESET (or RESET for TLV810E). There are at the most two external components: a
capacitor on the VDD pin and a pull-up resistor on the RESET/RESET to VDD or another pull-up voltage for the
open-drain variants. The design involves choosing the device with the desired voltage threshold and output
topology and adding these components, if needed, as explained in the following sections.
9.2 Typical Application
A typical application for TLV803E, TLV809E, and TLV810E devices is voltage rail monitoring. This rail can be the
input power supply or the output of an LDO or DC/DC converter. Figure 32 shows the TLV803EA29 monitoring
the supply rail for a DSP, FPGA, or ASIC. This rail is at 3.3 V and generated by an LDO with an input power
supply of 5 V. The supervisor is needed to make sure that the supply to the MCU/ASIC/FPGA/DSP is above a
certain voltage threshold. If the supply voltage drops below a certain threshold, supervisor generates a reset
output to indicate to the MCU that the supply is going down so that the MCU can take actions to save register
data before supply enters brown-out conditions.
LDO
3.3 V
5 V
IN
OUT
10 kQ
VDD
FPGA, ASIC, DSP
VDD
RESET
TLV803E
RESET
GND
GND
Figure 32. The Output of LDO Powering the MCU is Monitored by the TLV803EA29
9.2.1 Design Requirements
This design monitors a 3.3-V rail and flags an undervoltage fault at the RESET output when supply rail falls
approximately 12% below the nominal rail voltage. The TLV803E device has an open-drain output topology so a
pull-up resistor is required and chosen such that the RESET current (IRESET) spec of ±5 mA is not violated. Pull-
up resistors between 10 kΩ and 1 MΩ are recommended. If you are using the TLV809E device variant, no pull-
up resistor is required because TLV809E has push-pull output topology.
9.2.2 Detailed Design Procedure
Select the TLV803EA29DBZR to satisfy the voltage threshold requirement for 3.3-V rail monitoring. As
mentioned in , the TLV803EA29DBZR triggers an undervoltage fault at the RESET output when VDD falls below
VIT- which is 2.93 V for this device variant. Place a pull-up resistor on RESET to VDD to satisfy the output logic
requirement while not violating the IRESET recommended limit.
18
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
Typical Application (continued)
9.2.3 Application Curves
Figure 33 and Figure 34 show the TLV803EA29 functionality. In Figure 33, the VDD supply voltage drops from
30% above VIT- = 3.8 V to 10% below VIT- = 2.6 V with a 0.1-µF capacitor on VDD. The RESET output is
connected to VDD through the pull-up resistor so when the VDD supply voltage drops. The RESET output
discharges down to the VDD supply voltage through the pull-up resistor and RESET pin capacitance. Once the
high-to-low propagation delay tPD_HL expires, the internal MOSFET turns on and asserts RESET to logic low.
Note that tPD_HL varies with VDD specifically on how much VDD drops and how quickly in addition to the VDD
and RESET pin capacitances. In Figure 34, VDD rises from 2 V to 4 V and the RESET output deasserts to logic
high after the reset delay time (tD) expires.
VDD
VDD
Propagation Delay from VDD falling below VIT- to Reset
Reset Delay (tD) = 200 ms
(tPD_HL) = 25 µs
RESET
RESET
Figure 34. RESET Delay when Returning from Fault after
Figure 33. Propagation Delay when Fault Occurs after VDD
Falls Below VIT- (TLV803EA29 No Load) (1) (2)
VDD Rises Above VIT+ (TLV803EA29)
1. Typical tPD_HL= 30 µs for VDD falling from (VIT+ + 30%) to (VIT- - 10%).
2. VDD does not fall all the way to 0 V so RESET momentarily discharges to VDD until tPD_HL expires.
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
9.3 Typical Application
A typical use case for the push-pull active-high device variant TLV810E is overvoltage monitoring. The TLV810E
can monitor a power supply, a MCU power rail, or a battery during charging for example. The VDD pin monitors
the voltage rail and once VDD rises above VIT+, the RESET output deactivates to logic low after the reset delay
time tD. If VDD falls below VIT-, the RESET output activates to logic high after the propagation delay (tPD_HL). The
voiltage thresholds and the reset delay time depends on the device variant. See Device Comparison for device
variant naming nomenclature.
3 V
VDD
Battery Charger
VDD
RESET
TLV810EA29
ENABLE
GND
GND
Figure 35. TLV810E Overvoltage Monitor Circuit for Battery Charger
9.3.1 Design Requirements
In this application design, the TLV810E device is monitoring a 3 V battery connected to a battery charger. The
battery charger turns on when the battery voltage is below 2.93 V and turns off once the battery charges to 2.96
V and remains above 2.96 V for at least 200 ms. The design must be low power and not consume more than 500
nA typical.
9.3.2 Detailed Design Procedure
Select the TLV810EA29 to accomplish this design. The TLV810EA29 is a push-pull active-high device with a VIT-
= 2.9 V and VIT+ = 2.9 + 1.2% = 2.93 V. Because the device is a push-pull output and the device threshold meets
the design requirements, no external resistors are needed. The TLV810EA29 device variant comes with 200 ms
reset delay time meaning VDD must be above VIT+ for at least 200 ms for the RESET output to transistion to
logic low to turn off the battery charger. This device meets the low power requirement because the TLV810E only
consumes 250 nA typical.
20
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
10 Power Supply Recommendations
These devices are designed to operate from an input supply range of 1.7 V to 6 V. An input supply capacitor is
recommended between the VDD pin and GND pin. If the voltage supply that provides power to VDD is
susceptible to any large voltage transient that can exceed VDD maximum, the user must take additional
precautions.
11 Layout
11.1 Layout Guidelines
Make sure that the connection to the VDD pin is low impedance. Good analog design practice recommends
placing a minimum 0.1-µF ceramic capacitor as close to the VDD pin as possible. A pull-up resistor is required
for the open-drain output. Place the pull-up resistor on the RESET pin as close to the pin as possible.
11.2 Layout Example
1
2
GND
3
VDD
(TLV803E, TLV809E)
(TLV810E)
RESET
RESET
RESET
RESET
Figure 36. TLV803E, TLV809E, and TLV810E SOT23 (DBZ) Layout Example
Rpull-up
RESET
1
4
VDD
PAD
CIN
GND
2
MR
3
Pull-up resistor required for Open-Drain output
Connection between PAD and GND is optional
Figure 37. TLV803E, TLV809E, and TLV810E X2SON (DPW) Layout Example
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
12 Device and Documentation Support
12.1 Device Support
12.1.1 Device Nomenclature
shows how to decode the function of the device based on its part number. For example: TLV803EA29DBZR is
open-drain, active-low, 200 ms reset delay, 2.93 V threshold voltage, Pin 1 = GND, SOT23-3 pin package, and
large reel option.
shows all the possible variants of the TLV80xE and TLV81xE. Refer to the orderable device information table for
the options available to order. Contact Texas Instruments for the details and availability of devices not in the
orderable device information table.
Table 1. Device Naming Convention
DESCRIPTION
NOMENCLATURE
VALUE
Open-Drain, Active-Low
Part Number
TLV803E
TLV809E
Push-Pull, Active-Low
Push-Pull, Active-High
200 ms
TLV810E
A
Reset Time Delay Option
B
40 µs
C
10 ms
D
50 ms
E
100 ms
F
400 ms
Threshold Voltage Option
17
1.7 V
18
1.8 V
19
1.9 V
24
2.4 V
26
2.64 V
29
2.93 V
30
3.08 V
43
4.38 V
46
4.63 V
Reverse Pinout Indicator
Package Option
R
Pin 1 = RESET Pin 2 = GND
SOT23-3 pin
SC70-3 pin
X2SON-5 pin
Large reel
DBZ
DCK
DPW
R
Reel
22
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation see the following:
•
•
Texas Instruments, TLV803EA29EVM User Guide
Texas Instruments, Voltage Supervisors (Reset ICs): Frequenctly Asked Questions (FAQs)
12.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to order now.
Table 2. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
ORDER NOW
TLV803E
TLV809E
TLV810E
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
12.4 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.5 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.6 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.7 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.8 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
PACKAGE OUTLINE
DPW0004A
X2SON - 0.4 mm max height
S
C
A
L
E
1
2
.
0
0
0
PLASTIC SMALL OUTLINE - NO LEAD
0.85
0.75
A
B
PIN 1 INDEX AREA
0.85
0.75
0.4 MAX
C
SEATING PLANE
NOTE 4
(0.1)
0.25 0.1
0.05
0.00
THERMAL PAD
2
3
4
NOTE 4
5
2X
(45 ) TYP
0.48
1
0.27
4X
PIN 1 ID
(OPTIONAL)
NOTE 5
0.17
0.32
3X
0.1 C A
0.05 C
B
0.27
0.17
0.23
4218860/A 12/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
4. The size and shape of this feature may vary.
5. Features may not exist. Recommend use of pin 1 marking on top of package for orientation purposes.
www.ti.com
24
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
www.ti.com
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
EXAMPLE BOARD LAYOUT
DPW0004A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.78)
( 0.1)
VIA
SYMM
4X (0.42)
0.05 MIN
ALL AROUND
TYP
1
4
4X (0.22)
5
SYMM
4X (0.26)
(0.48)
2
3
(R0.05) TYP
SOLDER MASK
OPENING, TYP
4X (0.06)
(
0.25)
METAL UNDER
SOLDER MASK
TYP
LAND PATTERN EXAMPLE
SOLDER MASK DEFINED
SCALE:60X
4218860/A 12/2015
NOTES: (continued)
6. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
7. Vias are optional depending on application, refer to device data sheet. If some or all are implemented, recommended via locations are shown.
www.ti.com
Copyright © 2018–2020, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: TLV803E TLV809E TLV810E
TLV803E, TLV809E, TLV810E
SLVSES2F –AUGUST 2018–REVISED JUNE 2020
www.ti.com
EXAMPLE STENCIL DESIGN
DPW0004A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
4X (0.42)
4X (0.06)
4
1
4X (0.22)
(
0.24)
4X (0.26)
5
SYMM
(0.21)
(0.48)
TYP
SOLDER MASK
EDGE
2
3
(R0.05) TYP
SYMM
(0.78)
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
EXPOSED PAD 5:
92% PRINTED SOLDER COVERAGE BY AREA
SCALE:100X
4218860/A 12/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
26
Submit Documentation Feedback
Copyright © 2018–2020, Texas Instruments Incorporated
Product Folder Links: TLV803E TLV809E TLV810E
PACKAGE OPTION ADDENDUM
www.ti.com
25-Aug-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
DPW
DPW
DBZ
Qty
(1)
(2)
(3)
(4/5)
(6)
TLV803EA17DPWR
TLV803EA18DPWR
TLV803EA26DBZR
TLV803EA26DCKR
TLV803EA26DPWR
TLV803EA26RDBZR
TLV803EA29DBZR
TLV803EA29DCKR
TLV803EA29DPWR
TLV803EA29RDBZR
TLV803EA30DCKR
TLV803EA43DBZR
TLV803EA43RDBZR
TLV803EB29DBZR
TLV803EB46DCKR
TLV803EC29DBZR
ACTIVE
X2SON
X2SON
SOT-23
SC70
5
5
3
3
5
3
3
3
5
3
3
3
3
3
3
3
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
IT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Green (RoHS
& no Sb/Br)
NIPDAU
SN
IV
Green (RoHS
& no Sb/Br)
326A
32A
IW
DCK
DPW
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
SN
X2SON
SOT-23
SOT-23
SC70
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
36AR
329A
39A
IX
DBZ
Green (RoHS
& no Sb/Br)
SN
DCK
DPW
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
SN
X2SON
SOT-23
SC70
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
39AR
30A
343A
34AR
329B
36B
329C
DCK
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
SN
SOT-23
SOT-23
SOT-23
SC70
Green (RoHS
& no Sb/Br)
DBZ
Green (RoHS
& no Sb/Br)
SN
DBZ
Green (RoHS
& no Sb/Br)
SN
DCK
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
SN
SOT-23
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Aug-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TLV803EC30DBZR
TLV803ED17DPWR
TLV803ED18DPWR
TLV809EA26DBZR
TLV809EA26DPWR
TLV809EA29DBZR
TLV809EA29DCKR
TLV809EA29DPWR
TLV809EA30DBZR
TLV809EA43DBZR
TLV809EA46DBZR
TLV809EA46DPWR
TLV809EC26DBZR
TLV809EC46DBZR
TLV810EA29DBZR
TLV810EA29DPWR
ACTIVE
SOT-23
X2SON
X2SON
SOT-23
X2SON
SOT-23
SC70
DBZ
3
5
5
3
5
3
3
5
3
3
3
5
3
3
3
5
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
Green (RoHS
& no Sb/Br)
SN
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
330C
IS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DPW
DPW
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
SN
Green (RoHS
& no Sb/Br)
IU
Green (RoHS
& no Sb/Br)
926A
IZ
DPW
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
SN
Green (RoHS
& no Sb/Br)
929A
99A
J1
DCK
DPW
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
SN
X2SON
SOT-23
SOT-23
SOT-23
X2SON
SOT-23
SOT-23
SOT-23
X2SON
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
930A
943A
946A
J2
DBZ
Green (RoHS
& no Sb/Br)
SN
DBZ
Green (RoHS
& no Sb/Br)
SN
DPW
DBZ
Green (RoHS
& no Sb/Br)
NIPDAU
SN
Green (RoHS
& no Sb/Br)
926C
946C
029A
J3
DBZ
Green (RoHS
& no Sb/Br)
SN
DBZ
Green (RoHS
& no Sb/Br)
SN
DPW
Green (RoHS
& no Sb/Br)
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
25-Aug-2020
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Aug-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLV803EA17DPWR
TLV803EA18DPWR
TLV803EA26DBZR
TLV803EA26DCKR
TLV803EA26DPWR
TLV803EA26RDBZR
TLV803EA29DBZR
TLV803EA29DCKR
TLV803EA29DPWR
TLV803EA29RDBZR
TLV803EA30DCKR
TLV803EA43DBZR
TLV803EA43RDBZR
TLV803EB29DBZR
TLV803EB46DCKR
TLV803EC29DBZR
TLV803EC30DBZR
TLV803ED17DPWR
X2SON
X2SON
SOT-23
SC70
DPW
DPW
DBZ
DCK
DPW
DBZ
DBZ
DCK
DPW
DBZ
DCK
DBZ
DBZ
DBZ
DCK
DBZ
DBZ
DPW
5
5
3
3
5
3
3
3
5
3
3
3
3
3
3
3
3
5
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
9.0
9.0
8.4
9.0
9.0
9.0
8.4
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
8.4
0.91
0.91
3.15
2.4
0.91
0.91
2.77
2.5
0.5
0.5
2.0
2.0
4.0
4.0
2.0
4.0
4.0
4.0
2.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
2.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q2
Q2
Q3
Q3
Q2
Q3
Q3
Q3
Q2
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q2
1.22
1.2
X2SON
SOT-23
SOT-23
SC70
0.91
3.15
3.15
2.4
0.91
2.77
2.77
2.5
0.5
1.22
1.22
1.2
X2SON
SOT-23
SC70
0.91
3.15
2.4
0.91
2.77
2.5
0.5
1.22
1.2
SOT-23
SOT-23
SOT-23
SC70
3.15
3.15
3.15
2.4
2.77
2.77
2.77
2.5
1.22
1.22
1.22
1.2
SOT-23
SOT-23
X2SON
3.15
3.15
0.91
2.77
2.77
0.91
1.22
1.22
0.5
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Aug-2020
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLV803ED18DPWR
TLV809EA26DBZR
TLV809EA26DPWR
TLV809EA29DBZR
TLV809EA29DCKR
TLV809EA29DPWR
TLV809EA30DBZR
TLV809EA43DBZR
TLV809EA46DBZR
TLV809EA46DPWR
TLV809EC26DBZR
TLV809EC46DBZR
TLV810EA29DBZR
TLV810EA29DPWR
X2SON
SOT-23
X2SON
SOT-23
SC70
DPW
DBZ
DPW
DBZ
DCK
DPW
DBZ
DBZ
DBZ
DPW
DBZ
DBZ
DBZ
DPW
5
3
5
3
3
5
3
3
3
5
3
3
3
5
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
9.0
8.4
9.0
9.0
8.4
9.0
9.0
9.0
8.4
9.0
9.0
9.0
8.4
0.91
3.15
0.91
3.15
2.4
0.91
2.77
0.91
2.77
2.5
0.5
1.22
0.5
2.0
4.0
2.0
4.0
4.0
2.0
4.0
4.0
4.0
2.0
4.0
4.0
4.0
2.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q2
Q3
Q2
Q3
Q3
Q2
Q3
Q3
Q3
Q2
Q3
Q3
Q3
Q2
1.22
1.2
X2SON
SOT-23
SOT-23
SOT-23
X2SON
SOT-23
SOT-23
SOT-23
X2SON
0.91
3.15
3.15
3.15
0.91
3.15
3.15
3.15
0.91
0.91
2.77
2.77
2.77
0.91
2.77
2.77
2.77
0.91
0.5
1.22
1.22
1.22
0.5
1.22
1.22
1.22
0.5
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLV803EA17DPWR
TLV803EA18DPWR
TLV803EA26DBZR
X2SON
X2SON
SOT-23
DPW
DPW
DBZ
5
5
3
3000
3000
3000
205.0
205.0
180.0
200.0
200.0
180.0
33.0
33.0
18.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Aug-2020
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLV803EA26DCKR
TLV803EA26DPWR
TLV803EA26RDBZR
TLV803EA29DBZR
TLV803EA29DCKR
TLV803EA29DPWR
TLV803EA29RDBZR
TLV803EA30DCKR
TLV803EA43DBZR
TLV803EA43RDBZR
TLV803EB29DBZR
TLV803EB46DCKR
TLV803EC29DBZR
TLV803EC30DBZR
TLV803ED17DPWR
TLV803ED18DPWR
TLV809EA26DBZR
TLV809EA26DPWR
TLV809EA29DBZR
TLV809EA29DCKR
TLV809EA29DPWR
TLV809EA30DBZR
TLV809EA43DBZR
TLV809EA46DBZR
TLV809EA46DPWR
TLV809EC26DBZR
TLV809EC46DBZR
TLV810EA29DBZR
TLV810EA29DPWR
SC70
DCK
DPW
DBZ
DBZ
DCK
DPW
DBZ
DCK
DBZ
DBZ
DBZ
DCK
DBZ
DBZ
DPW
DPW
DBZ
DPW
DBZ
DCK
DPW
DBZ
DBZ
DBZ
DPW
DBZ
DBZ
DBZ
DPW
3
5
3
3
3
5
3
3
3
3
3
3
3
3
5
5
3
5
3
3
5
3
3
3
5
3
3
3
5
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
180.0
205.0
180.0
180.0
180.0
205.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
205.0
205.0
180.0
205.0
180.0
180.0
205.0
180.0
180.0
180.0
205.0
180.0
180.0
180.0
205.0
180.0
200.0
180.0
180.0
180.0
200.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
200.0
200.0
180.0
200.0
180.0
180.0
200.0
180.0
180.0
180.0
200.0
180.0
180.0
180.0
200.0
18.0
33.0
18.0
18.0
18.0
33.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
33.0
33.0
18.0
33.0
18.0
18.0
33.0
18.0
18.0
18.0
33.0
18.0
18.0
18.0
33.0
X2SON
SOT-23
SOT-23
SC70
X2SON
SOT-23
SC70
SOT-23
SOT-23
SOT-23
SC70
SOT-23
SOT-23
X2SON
X2SON
SOT-23
X2SON
SOT-23
SC70
X2SON
SOT-23
SOT-23
SOT-23
X2SON
SOT-23
SOT-23
SOT-23
X2SON
Pack Materials-Page 3
PACKAGE OUTLINE
DPW0005A
X2SON - 0.4 mm max height
S
C
A
L
E
1
2
.
0
0
0
PLASTIC SMALL OUTLINE - NO LEAD
0.85
0.75
A
B
PIN 1 INDEX AREA
0.85
0.75
0.4 MAX
C
SEATING PLANE
NOTE 3
(0.1)
0.05
0.00
(0.25)
4X (0.05)
0.25 0.1
2
1
4
5
NOTE 3
2X
0.48
3
2X (0.26)
0.27
0.17
4X
0.27
0.17
0.1 C A B
0.05 C
(0.06)
3X
0.32
0.23
4223102/B 09/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The size and shape of this feature may vary.
www.ti.com
EXAMPLE BOARD LAYOUT
DPW0005A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.78)
(
0.1)
SYMM
4X (0.42)
VIA
0.05 MIN
ALL AROUND
TYP
1
5
4X (0.22)
SYMM
4X (0.26)
(0.48)
3
2
4
(R0.05) TYP
SOLDER MASK
OPENING, TYP
4X (0.06)
(
0.25)
(0.21) TYP
EXPOSED METAL
CLEARANCE
METAL UNDER
SOLDER MASK
TYP
LAND PATTERN EXAMPLE
SOLDER MASK DEFINED
SCALE:60X
4223102/B 09/2017
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, refer to QFN/SON PCB application note
in literature No. SLUA271 (www.ti.com/lit/slua271).
www.ti.com
EXAMPLE STENCIL DESIGN
DPW0005A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
4X (0.42)
4X (0.06)
5
1
4X (0.22)
SYMM
(
0.24)
4X (0.26)
(0.21)
(0.48)
TYP
SOLDER MASK
EDGE
3
2
4
(R0.05) TYP
SYMM
(0.78)
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
EXPOSED PAD
92% PRINTED SOLDER COVERAGE BY AREA
SCALE:100X
4223102/B 09/2017
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
4203227/C
PACKAGE OUTLINE
DBZ0003A
SOT-23 - 1.12 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
2.64
2.10
1.12 MAX
1.4
1.2
B
A
0.1 C
PIN 1
INDEX AREA
1
0.95
3.04
2.80
1.9
3
2
0.5
0.3
3X
0.10
0.01
(0.95)
TYP
0.2
C A B
0.25
GAGE PLANE
0.20
0.08
TYP
0.6
0.2
TYP
SEATING PLANE
0 -8 TYP
4214838/C 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration TO-236, except minimum foot length.
www.ti.com
EXAMPLE BOARD LAYOUT
DBZ0003A
SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
PKG
3X (1.3)
1
3X (0.6)
SYMM
3
2X (0.95)
2
(R0.05) TYP
(2.1)
LAND PATTERN EXAMPLE
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214838/C 04/2017
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBZ0003A
SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
PKG
3X (1.3)
1
3X (0.6)
SYMM
3
2X(0.95)
2
(R0.05) TYP
(2.1)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:15X
4214838/C 04/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OUTLINE
DCK0003A
SOT-SC70 - 1.1 max height
S
C
A
L
E
5
.
6
0
0
SMALL OUTLINE TRANSISTOR SC70
C
2.4
1.8
0.1 C
1.4
1.1
B
1.1 MAX
A
PIN 1
INDEX AREA
1
2
0.65
1.3
2.15
1.85
3
0.30
3X
0.15
C A B
0.1
0.0
0.1
(0.9)
TYP
0.15
0.22
0.08
GAGE PLANE
TYP
0.46
0.26
8
TYP
TYP
0
SEATING PLANE
4220745/B 06/2020
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-203.
www.ti.com
EXAMPLE BOARD LAYOUT
DCK0003A
SOT-SC70 - 1.1 max height
SMALL OUTLINE TRANSISTOR SC70
PKG
3X (0.95)
3X (0.4)
1
SYMM
3
(1.3)
(0.65)
2
(R0.05) TYP
(2.2)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:18X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4220745/B 06/2020
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DCK0003A
SOT-SC70 - 1.1 max height
SMALL OUTLINE TRANSISTOR SC70
PKG
3X (0.95)
3X (0.4)
1
SYMM
3
(1.3)
(0.65)
2
(R0.05) TYP
(2.2)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:18X
4220745/B 06/2020
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
TLV803EA24DCKR
TLV803E, TLV809E, TLV810E Low Power 250-nA IQ and Small Size Supply Voltage Supervisors
TI
TLV803EA26DPWR
TLV803E, TLV809E, TLV810E Low Power 250-nA IQ and Small Size Supply Voltage Supervisors
TI
TLV803EA29DPWR
TLV803E, TLV809E, TLV810E Low Power 250-nA IQ and Small Size Supply Voltage Supervisors
TI
©2020 ICPDF网 联系我们和版权申明