TMS320C6711FN167 [TI]
FIXED-POINT DIGITAL SIGNAL PROCESSORS; 定点数字信号处理器型号: | TMS320C6711FN167 |
厂家: | TEXAS INSTRUMENTS |
描述: | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
文件: | 总87页 (文件大小:1251K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃꢄ ꢅꢆ ꢇꢄ ꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
D
D
Excellent Price/Performance Digital Signal
Processors (DSPs): TMS320C62x
(TMS320C6211 and TMS320C6211B)
− Eight 32-Bit Instructions/Cycle
− C6211, C6211B, C6711, and C6711B are
Pin-Compatible
− 150-, 167-MHz Clock Rates
− 6.7-, 6-ns Instruction Cycle Time
− 1200, 1333 MIPS
D
Device Configuration
− Boot Mode: HPI, 8-, 16-, and 32-Bit ROM
Boot
− Endianness: Little Endian, Big Endian
D
32-Bit External Memory Interface (EMIF)
− Glueless Interface to Asynchronous
Memories: SRAM and EPROM
− Glueless Interface to Synchronous
Memories: SDRAM and SBSRAM
− 512M-Byte Total Addressable External
Memory Space
− Extended Temperature Device (C6211B)
VelociTI Advanced Very Long Instruction
Word (VLIW) C62x DSP Core (C6211/11B)
− Eight Highly Independent Functional
Units:
D
D
D
Enhanced Direct-Memory-Access (EDMA)
Controller (16 Independent Channels)
16-Bit Host-Port Interface (HPI)
− Access to Entire Memory Map
− Six ALUs (32-/40-Bit)
− Two 16-Bit Multipliers (32-Bit Results)
− Load-Store Architecture With 32 32-Bit
General-Purpose Registers
− Instruction Packing Reduces Code Size
− All Instructions Conditional
Two Multichannel Buffered Serial Ports
(McBSPs)
− Direct Interface to T1/E1, MVIP, SCSA
Framers
− ST-Bus-Switching Compatible
− Up to 256 Channels Each
− AC97-Compatible
− Serial-Peripheral-Interface (SPI)
Compatible (Motorola)
D
D
Instruction Set Features
− Byte-Addressable (8-, 16-, 32-Bit Data)
− 8-Bit Overflow Protection
− Saturation
− Bit-Field Extract, Set, Clear
− Bit-Counting
D
D
Two 32-Bit General-Purpose Timers
− Normalization
Flexible Phase-Locked-Loop (PLL) Clock
Generator
L1/L2 Memory Architecture
− 32K-Bit (4K-Byte) L1P Program Cache
(Direct Mapped)
− 32K-Bit (4K-Byte) L1D Data Cache
(2-Way Set-Associative)
†
D
D
D
D
IEEE-1149.1 (JTAG )
Boundary-Scan-Compatible
256-Pin Ball Grid Array (BGA) Package
(GFN and ZFN Suffixes)
− 512K-Bit (64K-Byte) L2 Unified Mapped
RAM/Cache
0.18-µm/5-Level Metal Process
− CMOS Technology
(Flexible Data/Program Allocation)
3.3-V I/Os, 1.8-V Internal
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TMS320C62x, VelociTI, and C62x are trademarks of Texas Instruments.
Motorola is a trademark of Motorola, Inc.
All trademarks are the property of their respective owners.
†
IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
ꢑ
ꢑ
ꢗ
ꢒ
ꢨ
ꢏ
ꢣ
ꢘ
ꢆ
ꢡ
ꢀ
ꢢ
ꢌ
ꢜ
ꢒ
ꢚ
ꢓ
ꢛ
ꢏ
ꢕ
ꢀ
ꢕ
ꢙ
ꢚ
ꢤ
ꢛ
ꢜ
ꢢ
ꢝ
ꢞ
ꢟ
ꢟ
ꢠ
ꢠ
ꢙ
ꢙ
ꢜ
ꢜ
ꢚ
ꢚ
ꢙ
ꢡ
ꢡ
ꢥ
ꢢ
ꢣ
ꢝ
ꢝ
ꢤ
ꢤ
ꢚ
ꢠ
ꢟ
ꢞ
ꢡ
ꢡ
ꢜ
ꢛ
ꢥ
ꢀꢤ
ꢣ
ꢦ
ꢡ
ꢧ
ꢙ
ꢢ
ꢟ
ꢡ
ꢠ
ꢙ
ꢠ
ꢜ
ꢝ
ꢚ
ꢣ
ꢨ
ꢟ
ꢚ
ꢠ
ꢠ
ꢤ
ꢡ
ꢩ
Copyright 2004, Texas Instruments Incorporated
ꢝ
ꢜ
ꢢ
ꢠ
ꢜ
ꢝ
ꢞ
ꢠ
ꢜ
ꢡ
ꢥ
ꢙ
ꢛ
ꢙ
ꢢ
ꢤ
ꢝ
ꢠ
ꢪ
ꢠ
ꢤ
ꢝ
ꢜ
ꢛ
ꢫ
ꢟ
ꢌ
ꢚ
ꢞ
ꢤ
ꢡ
ꢠ
ꢟ
ꢚ
ꢨ
ꢟ
ꢝ
ꢨ
ꢬ
ꢟ
ꢠ ꢤ ꢡ ꢠꢙ ꢚꢮ ꢜꢛ ꢟ ꢧꢧ ꢥꢟ ꢝ ꢟ ꢞ ꢤ ꢠ ꢤ ꢝ ꢡ ꢩ
ꢝ
ꢝ
ꢟ
ꢚ
ꢠ
ꢭ
ꢩ
ꢑ
ꢝ
ꢜ
ꢨ
ꢣ
ꢢ
ꢠ
ꢙ
ꢜ
ꢚ
ꢥ
ꢝ
ꢜ
ꢢ
ꢤ
ꢡ
ꢡ
ꢙ
ꢚ
ꢮ
ꢨ
ꢜ
ꢤ
ꢡ
ꢚ
ꢜ
ꢠ
ꢚ
ꢤ
ꢢ
ꢤ
ꢡ
ꢡ
ꢟ
ꢝ
ꢙ
ꢧ
ꢭ
ꢙ
ꢚ
ꢢ
ꢧ
ꢣ
ꢨ
ꢤ
1
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Table of Contents
revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
GFN and ZFN BGA packages (bottom view) . . . . . . . . . . . . 4
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
device compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
functional block and CPU (DSP core) diagram . . . . . . . . . . . 8
CPU (DSP core) description . . . . . . . . . . . . . . . . . . . . . . . . . . 9
memory map summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
peripheral register descriptions . . . . . . . . . . . . . . . . . . . . . . . 12
PWRD bits in CPU CSR register description . . . . . . . . . . . 17
EDMA channel synchronization events . . . . . . . . . . . . . . . . 18
interrupt sources and interrupt selector . . . . . . . . . . . . . . . . 19
signal groups description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
terminal functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
documentation support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
clock PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
power-down logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
power-supply sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
IEEE 1149.1 JTAG compatibility statement . . . . . . . . . . . . . 40
EMIF device speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
absolute maximum ratings over operating case
temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . 42
recommended operating conditions . . . . . . . . . . . . . . . . 42
electrical characteristics over recommended ranges of
supply voltage and operating case temperature . 42
parameter measurement information . . . . . . . . . . . . . . . 43
signal transition levels . . . . . . . . . . . . . . . . . . . . . . . . . . 43
timing parameters and board routing analysis . . . . . . 44
input and output clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
asynchronous memory timing . . . . . . . . . . . . . . . . . . . . . 49
synchronous-burst memory timing . . . . . . . . . . . . . . . . . 52
synchronous DRAM timing . . . . . . . . . . . . . . . . . . . . . . . . 54
HOLD/HOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
BUSREQ timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
external interrupt timing . . . . . . . . . . . . . . . . . . . . . . . . . . 64
host-port interface timing . . . . . . . . . . . . . . . . . . . . . . . . . 65
multichannel buffered serial port timing . . . . . . . . . . . . . 69
timer timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
JTAG test-port timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
2
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
REVISION HISTORY
This data sheet revision history highlights the technical changes made to the SPRS073K device-specific data
sheet to make it an SPRS073L revision.
Scope: Applicable updates to the C62x device family, specifically relating to the C6211 and C6211B devices,
have been incorporated.
PAGE(S)
ADDITIONS/CHANGES/DELETIONS
NO.
Global:
Added “ZFN” mechanical packaging information
3
Moved the Revision History to the front of the document
31
Device Support, Device and Development-Support Tool Nomenclature section:
Updated the “To designate the stages in the product development cycle...” paragraph
Updated the “TMX and TMP devices...” paragraph
Added “The ZFN package, like the GFN package, is ...” paragraph
32
Figure 4. TMS320C6000 DSP Device Nomenclature (Including the TMS320C6211 and TMS320C6211B Devices):
Deleted the “TMS320C6211/C6211B Device Part Numbers (P/Ns) and Ordering Information” table and associated
paragraph
Added “ZFN” package and associated footnote
Added the “For actual device part numbers (P/Ns) and ordering information, ...” footnote
82, 83
Mechanical Data section:
Deleted the “GFN (S-PBGA-N256)” mechanical data package diagram; now an automated merge process
Added “thermal resistance characteristics (S-PBGA package) for ZFN” table
Added new “Packaging Information” title and lead-in sentence
3
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
GFN and ZFN BGA packages (bottom view)
GFN and ZFN 256-PIN BALL GRID ARRAY (BGA) PACKAGES
(BOTTOM VIEW)
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
3
5
7
9
11 13
12
15
17
19
2
4
6
8
10
14
16
18
20
4
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
description
The TMS320C62x DSPs (including the TMS320C6211/C6211B devices) compose one of the fixed-point DSP
families in the TMS320C6000 DSP platform. The TMS320C6211 (C6211) and TMS320C6211B (C6211B)
devices are based on the high-performance, advanced VelociTI very-long-instruction-word (VLIW)
architecture developed by Texas Instruments (TI), making these DSPs an excellent choice for multichannel and
multifunction applications.
With performance of up to 1333 million instructions per second (MIPS) at a clock rate of 167 MHz, the
C6211/C6211B device offers cost-effective solutions to high-performance DSP programming challenges. The
C6211/C6211B DSP possesses the operational flexibility of high-speed controllers and the numerical capability
of array processors. This processor has 32 general-purpose registers of 32-bit word length and eight highly
independent functional units. The eight functional units provide six arithmetic logic units (ALUs) for a high
degree of parallelism and two 16-bit multipliers for a 32-bit result. The C6211/C6211B can produce two
multiply-accumulates (MACs) per cycle for a total of 333 million MACs per second (MMACS). The
C6211/C6211B DSP also has application-specific hardware logic, on-chip memory, and additional on-chip
peripherals.
The C6211/C6211B uses a two-level cache-based architecture and has a powerful and diverse set of
peripherals. The Level 1 program cache (L1P) is a 32-Kbit direct mapped cache and the Level 1 data cache
(L1D) is a 32-Kbit 2-way set-associative cache. The Level 2 memory/cache (L2) consists of a 512-Kbit memory
space that is shared between program and data space. L2 memory can be configured as mapped memory,
cache, or combinations of the two.The peripheral set includes two multichannel buffered serial ports (McBSPs),
two general-purpose timers, a host-port interface (HPI), and a glueless external memory interface (EMIF)
capable of interfacing to SDRAM, SBSRAM and asynchronous peripherals.
The C6211/C6211B has a complete set of development tools which includes: a new C compiler, an assembly
optimizer to simplify programming and scheduling, and a Windows debugger interface for visibility into source
code execution.
TMS320C6000 is a trademark of Texas Instruments.
Windows is a registered trademark of the Microsoft Corporation.
5
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
device characteristics
Table 1 provides an overview of the C6211/C6211B DSP. The table shows significant features of each device,
including the capacity of on-chip RAM, the peripherals, the execution time, and the package type with pin count.
For more details on the C6000 DSP device part numbers and part numbering, see Figure 4.
Table 1. Characteristics of the C6211/C6211B Processors
C6211
(FIXED-POINT DSP)
C6211B
(FIXED-POINT DSP)
HARDWARE FEATURES
EMIF
1
1
(Clock source = ECLKIN)
EDMA
(Internal clock source =
CPU clock frequency)
1
1
2
1
1
2
HPI
Peripherals
McBSPs
(Internal clock source =
CPU/2 clock frequency)
32-Bit Timers
(Internal clock source =
CPU/4 clock frequency)
2
2
Size (Bytes)
72K
72K
On-Chip
Memory
4K-Byte (4KB) L1 Program (L1P) Cache
4KB L1 Data (L1D) Cache
4K-Byte (4KB) L1 Program (L1P) Cache
4KB L1 Data (L1D) Cache
Organization
64KB Unified Mapped RAM/Cache (L2)
64KB Unified Mapped RAM/Cache (L2)
CPU ID+
CPU Rev ID
Control Status Register
(CSR.[31:16])
0x0002
0x0002
Frequency
MHz
167, 150
167, 150
6 ns (C6211B-167)
6.7 ns (C6211B-150)
6.7 ns (C6211BGFNA-150)
6 ns (C6211-167)
6.7 ns (C6211-150)
Cycle Time
ns
Core (V)
1.8
3.3
1.8
3.3
Voltage
I/O (V)
PLL Options
CLKIN frequency multiplier
27 x 27 mm
Bypass (x1), x4
256-Pin BGA (GFN)
Bypass (x1), x4
256-Pin BGA (GFN and ZFN)
BGA Packages
Process
Technology
µm
0.18 µm
0.18 µm
Product Status
Product Preview (PP)
Advance Information (AI)
Production Data (PD)
PD
PD
C6000 is a trademark of Texas Instruments.
6
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
device compatibility
The TMS320C6211/C6211B and C6711/C6711B devices are pin-compatible and have the same peripheral set;
thus, making new system designs easier and providing faster time to market. The following list summarizes the
device characteristic differences among the C6211, C6211B, C6711, and C6711B devices:
D
D
The C6211 and C6211B devices have a fixed-point C62x CPU, while the C6711 and C6711B devices have
a floating-point C67x CPU.
The C6211/C6211B device runs at -167 and -150 MHz clock speeds (with a C6211BGFNA extended
temperature device that also runs at -150 MHz), while the C6711/C6711B device runs at -150 and -100 MHz
(with a C6711BGFNA extended temperature device that also runs at -100 MHz).
For a more detailed discussion on the similarities/differences between the C6211 and C6711 devices, see the
How to Begin Development Today with the TMS320C6211 DSP and How to Begin Development with the
TMS320C6711 DSP application reports (literature number SPRA474 and SPRA522, respectively).
7
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
functional block and CPU (DSP core) diagram
C6211/C6211B Digital Signal Processors
SDRAM
External
SBSRAM
32
Memory
Interface
(EMIF)
L1P Cache
Direct Mapped
4K Bytes Total
SRAM
ROM/FLASH
I/O Devices
Timer 0
Timer 1
C6000 CPU (DSP Core)
Instruction Fetch
Control
L2
Registers
Instruction Dispatch
Instruction Decode
Memory
4 Banks
64K Bytes
Total
Enhanced
DMA
Controller
(16 channel)
Control
Logic
Multichannel
Buffered
Serial Port 1
(McBSP1)
Data Path A
Data Path B
Framing Chips:
H.100, MVIP,
SCSA, T1, E1
AC97 Devices,
SPI Devices,
Codecs
Test
A Register File
B Register File
In-Circuit
Emulation
Multichannel
Buffered
Serial Port 0
(McBSP0)
Interrupt
Control
.L1 .S1 .M1 .D1
.D2 .M2 .S2 .L2
L1D Cache
2-Way Set
Associative
4K Bytes Total
Host Port
Interface
(HPI)
16
Power-Down
Logic
PLL
(x1, x4)
Boot
Configuration
Interrupt
Selector
8
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
CPU (DSP core) description
The CPU fetches VelociTI advanced very-long instruction words (VLIW) (256 bits wide) to supply up to eight
32-bit instructions to the eight functional units during every clock cycle. The VelociTI VLIW architecture
features controls by which all eight units do not have to be supplied with instructions if they are not ready to
execute. The first bit of every 32-bit instruction determines if the next instruction belongs to the same execute
packet as the previous instruction, or whether it should be executed in the following clock as a part of the next
execute packet. Fetch packets are always 256 bits wide; however, the execute packets can vary in size. The
variable-length execute packets are a key memory-saving feature, distinguishing the C62x CPU from other
VLIW architectures.
The CPU features two sets of functional units. Each set contains four units and a register file. One set contains
functional units .L1, .S1, .M1, and .D1; the other set contains units .D2, .M2, .S2, and .L2. The two register files
each contain 16 32-bit registers for a total of 32 general-purpose registers. The two sets of functional units, along
with two register files, compose sides A and B of the CPU (see the functional block and CPU diagram and
Figure 1). The four functional units on each side of the CPU can freely share the 16 registers belonging to that
side. Additionally, each side features a single data bus connected to all the registers on the other side, by which
the two sets of functional units can access data from the register files on the opposite side. While register access
by functional units on the same side of the CPU as the register file can service all the units in a single clock cycle,
register access using the register file across the CPU supports one read and one write per cycle.
Another key feature of the C62x CPU is the load/store architecture, where all instructions operate on registers
(as opposed to data in memory). Two sets of data-addressing units (.D1 and .D2) are responsible for all data
transfers between the register files and the memory. The data address driven by the .D units allows data
addresses generated from one register file to be used to load or store data to or from the other register file. The
C62x CPU supports a variety of indirect addressing modes using either linear- or circular-addressing modes
with 5- or 15-bit offsets. All instructions are conditional, and most can access any one of the 32 registers. Some
registers, however, are singled out to support specific addressing or to hold the condition for conditional
instructions (if the condition is not automatically “true”). The two .M functional units are dedicated for multiplies.
The two .S and .L functional units perform a general set of arithmetic, logical, and branch functions with results
available every clock cycle.
The processing flow begins when a 256-bit-wide instruction fetch packet is fetched from a program memory.
The 32-bit instructions destined for the individual functional units are “linked” together by “1” bits in the least
significant bit (LSB) position of the instructions. The instructions that are “chained” together for simultaneous
execution (up to eight in total) compose an execute packet. A “0” in the LSB of an instruction breaks the chain,
effectively placing the instructions that follow it in the next execute packet. If an execute packet crosses the
fetch-packet boundary (256 bits wide), the assembler places it in the next fetch packet, while the remainder of
the current fetch packet is padded with NOP instructions. The number of execute packets within a fetch packet
can vary from one to eight. Execute packets are dispatched to their respective functional units at the rate of one
per clock cycle and the next 256-bit fetch packet is not fetched until all the execute packets from the current fetch
packet have been dispatched. After decoding, the instructions simultaneously drive all active functional units
for a maximum execution rate of eight instructions every clock cycle. While most results are stored in 32-bit
registers, they can be subsequently moved to memory as bytes or half-words as well. All load and store
instructions are byte-, half-word, or word-addressable.
9
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
CPU (DSP core) description (continued)
src1
src2
.L1
dst
long dst
long src
8
8
32
ST1
8
long src
long dst
dst
Register
File A
Data Path A
.S1
src1
(A0−A15)
src2
dst
src1
.M1
src2
LD1
dst
src1
src2
.D1
.D2
DA1
2X
1X
src2
src1
dst
DA2
LD2
src2
.M2
.S2
src1
dst
src2
Register
File B
(B0−B15)
Data Path B
src1
dst
long dst
long src
8
32
8
ST2
8
long src
long dst
dst
.L2
src2
src1
Control
Register
File
Figure 1. TMS320C62x CPU (DSP Core) Data Paths
10
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
memory map summary
Table 2 shows the memory map address ranges of the C6211/C6211B devices. Internal memory is always
located at address 0 and can be used as both program and data memory. The C6211/C6211B configuration
registers for the common peripherals are located at the same hex address ranges. The external memory
address ranges in the C6211/C6211B devices begin at the address location 0x8000 0000.
Table 2. TMS320C6211/C6211B Memory Map Summary
MEMORY BLOCK DESCRIPTION
Internal RAM (L2)
BLOCK SIZE (BYTES)
HEX ADDRESS RANGE
0000 0000 – 0000 FFFF
0001 0000 – 017F FFFF
0180 0000 – 0183 FFFF
0184 0000 – 0187 FFFF
0188 0000 – 018B FFFF
018C 0000 – 018F FFFF
0190 0000 – 0193 FFFF
0194 0000 – 0197 FFFF
0198 0000 – 019B FFFF
019C 0000 – 019F FFFF
01A0 0000 – 01A3 FFFF
01A4 0000 – 01FF FFFF
0200 0000 – 0200 0033
0200 0034 – 2FFF FFFF
3000 0000 – 3FFF FFFF
4000 0000 – 7FFF FFFF
8000 0000 – 8FFF FFFF
9000 0000 – 9FFF FFFF
A000 0000 – AFFF FFFF
B000 0000 – BFFF FFFF
C000 0000 – FFFF FFFF
64K
24M – 64K
256K
Reserved
External Memory Interface (EMIF) Registers
L2 Registers
256K
HPI Registers
256K
McBSP 0 Registers
McBSP 1 Registers
Timer 0 Registers
256K
256K
256K
Timer 1 Registers
256K
Interrupt Selector Registers
EDMA RAM and EDMA Registers
Reserved
256K
256K
6M – 256K
52
QDMA Registers
Reserved
736M – 52
256M
1G
McBSP 0/1 Data
Reserved
†
†
†
†
EMIF CE0
EMIF CE1
EMIF CE2
EMIF CE3
256M
256M
256M
256M
1G
Reserved
†
The number of EMIF address pins (EA[21:2]) limits the maximum addressable memory (SDRAM) to 128MB per CE space. To get 256MB of
addressable memory, additional general-purpose output pin or external logic is required.
11
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
peripheral register descriptions
Table 3 through Table 13 identify the peripheral registers for the C6211/C6211B device by their register names,
acronyms, and hex address or hex address range. For more detailed information on the register contents, bit
names, and their descriptions, see the TMS320C6000 DSP Peripherals Overview Reference Guide (literature
number SPRU190).
Table 3. EMIF Registers
HEX ADDRESS RANGE
0180 0000
ACRONYM
GBLCTL
CECTL1
CECTL0
−
REGISTER NAME
EMIF global control
EMIF CE1 space control
EMIF CE0 space control
Reserved
0180 0004
0180 0008
0180 000C
0180 0010
CECTL2
CECTL3
SDCTL
SDTIM
SDEXT
−
EMIF CE2 space control
EMIF CE3 space control
EMIF SDRAM control
EMIF SDRAM refresh control
EMIF SDRAM extension
Reserved
0180 0014
0180 0018
0180 001C
0180 0020
0180 0024 − 0183 FFFF
Table 4. L2 Cache Registers
HEX ADDRESS RANGE
0184 0000
ACRONYM
CCFG
REGISTER NAME
Cache configuration register
0184 4000
L2FBAR
L2FWC
L2CBAR
L2CWC
L1PFBAR
L1PFWC
L1DFBAR
L1DFWC
L2FLUSH
L2CLEAN
MAR0
L2 flush base address register
0184 4004
L2 flush word count register
0184 4010
L2 clean base address register
0184 4014
L2 clean word count register
0184 4020
L1P flush base address register
0184 4024
L1P flush word count register
0184 4030
L1D flush base address register
0184 4034
L1D flush word count register
0184 5000
L2 flush register
0184 5004
L2 clean register
0184 8200
Controls CE0 range 8000 0000 − 80FF FFFF
Controls CE0 range 8100 0000 − 81FF FFFF
Controls CE0 range 8200 0000 − 82FF FFFF
Controls CE0 range 8300 0000 − 83FF FFFF
Controls CE1 range 9000 0000 − 90FF FFFF
Controls CE1 range 9100 0000 − 91FF FFFF
Controls CE1 range 9200 0000 − 92FF FFFF
Controls CE1 range 9300 0000 − 93FF FFFF
Controls CE2 range A000 0000 − A0FF FFFF
Controls CE2 range A100 0000 − A1FF FFFF
Controls CE2 range A200 0000 − A2FF FFFF
Controls CE2 range A300 0000 − A3FF FFFF
Controls CE3 range B000 0000 − B0FF FFFF
Controls CE3 range B100 0000 − B1FF FFFF
Controls CE3 range B200 0000 − B2FF FFFF
Controls CE3 range B300 0000 − B3FF FFFF
Reserved
0184 8204
MAR1
0184 8208
MAR2
0184 820C
0184 8240
MAR3
MAR4
0184 8244
MAR5
0184 8248
MAR6
0184 824C
0184 8280
MAR7
MAR8
0184 8284
MAR9
0184 8288
MAR10
MAR11
MAR12
MAR13
MAR14
MAR15
−
0184 828C
0184 82C0
0184 82C4
0184 82C8
0184 82CC
0184 82D0 − 0187 FFFF
12
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
peripheral register descriptions (continued)
Table 5. EDMA Registers
HEX ADDRESS RANGE
01A0 FF9C − 01A0 FFDC
01A0 FFE0
ACRONYM
−
REGISTER NAME
Reserved
PQSR
CIPR
CIER
CCER
ER
Priority queue status register
Channel interrupt pending register
Channel interrupt enable register
Channel chain enable register
Event register
01A0 FFE4
01A0 FFE8
01A0 FFEC
01A0 FFF0
01A0 FFF4
EER
ECR
ESR
–
Event enable register
Event clear register
01A0 FFF8
01A0 FFFC
Event set register
01A1 0000 − 01A3 FFFF
Reserved
†
Table 6. EDMA Parameter RAM
HEX ADDRESS RANGE
01A0 0000 − 01A0 0017
01A0 0018 − 01A0 002F
01A0 0030 − 01A0 0047
01A0 0048 − 01A0 005F
01A0 0060 − 01A0 0077
01A0 0078 − 01A0 008F
01A0 0090 − 01A0 00A7
01A0 00A8 − 01A0 00BF
01A0 00C0 − 01A0 00D7
01A0 00D8 − 01A0 00EF
01A0 00F0 − 01A0 00107
01A0 0108 − 01A0 011F
01A0 0120 − 01A0 0137
01A0 0138 − 01A0 014F
01A0 0150 − 01A0 0167
01A0 0168 − 01A0 017F
01A0 0180 − 01A0 0197
01A0 0198 − 01A0 01AF
...
ACRONYM
REGISTER NAME
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
Parameters for Event 0 (6 words)
Parameters for Event 1 (6 words)
Parameters for Event 2 (6 words)
Parameters for Event 3 (6 words)
Parameters for Event 4 (6 words)
Parameters for Event 5 (6 words)
Parameters for Event 6 (6 words)
Parameters for Event 7 (6 words)
Parameters for Event 8 (6 words)
Parameters for Event 9 (6 words)
Parameters for Event 10 (6 words)
Parameters for Event 11 (6 words)
Parameters for Event 12 (6 words)
Parameters for Event 13 (6 words)
Parameters for Event 14 (6 words)
Parameters for Event 15 (6 words)
Reload/link parameters for Event M (6 words)
Reload/link parameters for Event N (6 words)
...
01A0 07E0 − 01A0 07F7
01A0 07F8 − 01A0 07FF
−
−
Reload/link parameters for Event Z (6 words)
Scratch pad area (2 words)
†
The C6211/C6211B device has sixty-nine parameter sets [six (6) words each] that can be used to reload/link EDMA transfers.
13
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
peripheral register descriptions (continued)
†
Table 7. Quick DMA (QDMA) and Pseudo Registers
HEX ADDRESS RANGE
0200 0000
ACRONYM
QOPT
QSRC
QCNT
QDST
QIDX
REGISTER NAME
QDMA options parameter register
QDMA source address register
QDMA frame count register
QDMA destination address register
QDMA index register
0200 0004
0200 0008
0200 000C
0200 0010
0200 0014 − 0200 001C
0200 0020
−
Reserved
QSOPT
QSSRC
QSCNT
QSDST
QSIDX
QDMA pseudo options register
0200 0024
QDMA pseudo source address register
QDMA pseudo frame count register
QDMA pseudo destination address register
QDMA pseudo index register
0200 0028
0200 002C
0200 0030
†
All the QDMA and Pseudo registers are write-accessible only
Table 8. Interrupt Selector Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
Selects which interrupts drive CPU interrupts
10−15 (INT10−INT15)
019C 0000
MUXH
Interrupt multiplexer high
Selects which interrupts drive CPU interrupts 4−9
(INT04−INT09)
019C 0004
MUXL
Interrupt multiplexer low
Sets the polarity of the external interrupts
(EXT_INT4−EXT_INT7)
019C 0008
EXTPOL
−
External interrupt polarity
Reserved
019C 000C − 019F FFFF
14
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
peripheral register descriptions (continued)
Table 9. McBSP 0 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
The CPU and DMA/EDMA
controller can only read this
register; they cannot write to
it.
018C 0000
DRR0
McBSP0 data receive register via Peripheral Bus
0x3000 0000 − 0x33FF FFFF
018C 0004
DRR0
DXR0
DXR0
SPCR0
RCR0
XCR0
SRGR0
MCR0
RCER0
XCER0
PCR0
−
McBSP0 data receive register via EDMA Bus
McBSP0 data transmit register via Peripheral Bus
McBSP0 data transmit register via EDMA Bus
McBSP0 serial port control register
McBSP0 receive control register
0x3000 0000 − 0x33FF FFFF
018C 0008
018C 000C
018C 0010
McBSP0 transmit control register
018C 0014
McBSP0 sample rate generator register
McBSP0 multichannel control register
McBSP0 receive channel enable register
McBSP0 transmit channel enable register
McBSP0 pin control register
018C 0018
018C 001C
018C 0020
018C 0024
018C 0028 − 018F FFFF
Reserved
Table 10. McBSP 1 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
The CPU and DMA/EDMA
controller can only read this
register; they cannot write to
it.
0190 0000
DRR1
Data receive register via Peripheral Bus
0x3400 0000 − 0x37FF FFFF
0190 0004
DRR1
DXR1
DXR1
SPCR1
RCR1
XCR1
SRGR1
MCR1
RCER1
XCER1
PCR1
−
McBSP1 data receive register via EDMA Bus
McBSP1 data transmit register via Peripheral Bus
McBSP1 data transmit register via EDMA Bus
McBSP1 serial port control register
McBSP1 receive control register
0x3400 0000 − 0x37FF FFFF
0190 0008
0190 000C
0190 0010
McBSP1 transmit control register
0190 0014
McBSP1 sample rate generator register
McBSP1 multichannel control register
McBSP1 receive channel enable register
McBSP1 transmit channel enable register
McBSP1 pin control register
0190 0018
0190 001C
0190 0020
0190 0024
0190 0028 − 0193 FFFF
Reserved
15
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
peripheral register descriptions (continued)
Table 11. Timer 0 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
Determines the operating mode of the timer,
monitors the timer status, and controls the function
of the TOUT pin.
0194 0000
CTL0
Timer 0 control register
Contains the number of timer input clock cycles to
count. This number controls the TSTAT signal
frequency.
0194 0004
PRD0
Timer 0 period register
Contains the current value of the incrementing
counter.
0194 0008
CNT0
−
Timer 0 counter register
Reserved
0194 000C − 0197 FFFF
Table 12. Timer 1 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
Determines the operating mode of the timer,
monitors the timer status, and controls the function
of the TOUT pin.
0198 0000
CTL1
Timer 1 control register
Contains the number of timer input clock cycles to
count. This number controls the TSTAT signal
frequency.
0198 0004
PRD1
Timer 1 period register
Contains the current value of the incrementing
counter.
0198 0008
CNT1
−
Timer 1 counter register
Reserved
0198 000C − 019B FFFF
Table 13. HPI Registers
HEX ADDRESS RANGE
ACRONYM
HPID
HPIA
REGISTER NAME
HPI data register
COMMENTS
Host read/write access only
Host read/write access only
Both Host/CPU read/write access
−
−
HPI address register
HPI control register
Reserved
0188 0000
HPIC
−
0188 0001 − 018B FFFF
16
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
PWRD bits in CPU CSR register description
Table 14 identifies the PWRD field (bits 15−10) in the CPU CSR register. These bits control the device
power-down modes. For more detailed information on the PWRD bit field of the CPU CSR register, see the
TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Table 14. PWRD field bits in the CPU CSR Register
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
The PWRD field (bits 15−10 in the CPU CSR)
controls the device power-down modes.
−
CSR
Control status register
Accessible by writing a value to the CSR register.
17
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
EDMA channel synchronization events
The C62x EDMA supports up to 16 EDMA channels. Four of the sixteen channels (channels 8−11) are reserved
for EDMA chaining, leaving 12 EDMA channels available to service peripheral devices. Table 15 lists the source
of synchronization events associated with each of the programmable EDMA channels. For the C6211/11B, the
association of an event to a channel is fixed; each of the EDMA channels has one specific event associated
with it. For more detailed information on the EDMA module, associated channels, and event-transfer chaining,
see the TMS320C6000 DSP Enhanced Direct Memory Access (EDMA) Controller Reference Guide (literature
number SPRU234).
Table 15. TMS320C6211/C6211B EDMA Channel Synchronization Events
EDMA
CHANNEL
EVENT NAME
EVENT DESCRIPTION
Host-port interface (HPI)-to-DSP interrupt
0
1
2
3
4
5
6
7
DSP_INT
TINT0
Timer 0 interrupt
TINT1
Timer 1 interrupt
SD_INT
EMIF SDRAM timer interrupt
External interrupt pin 4
EXT_INT4
EXT_INT5
EXT_INT6
EXT_INT7
EDMA_TCC8
EDMA_TCC9
EDMA_TCC10
EDMA_TCC11
XEVT0
External interrupt pin 5
External interrupt pin 6
External interrupt pin 7
†
8
9
EDMA transfer complete code (TCC) 1000b interrupt
EDMA TCC 1001b interrupt
EDMA TCC 1010b interrupt
EDMA TCC 1011b interrupt
McBSP0 transmit event
McBSP0 receive event
†
†
10
†
11
12
13
14
15
REVT0
XEVT1
McBSP1 transmit event
McBSP1 receive event
REVT1
†
EDMA channels 8 through 11 are used for transfer chaining only. For more detailed information on event-transfer chaining, see the
TMS320C6000 DSP Enhanced Direct Memory Access (EDMA) Controller Reference Guide (literature number SPRU234).
18
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
interrupt sources and interrupt selector
The C62x DSP core supports 16 prioritized interrupts, which are listed in Table 16. The highest-priority interrupt
is INT_00 (dedicated to RESET) while the lowest-priority interrupt is INT_15. The first four interrupts
(INT_00−INT_03) are non-maskable and fixed. The remaining interrupts (INT_04−INT_15) are maskable and
default to the interrupt source specified in Table 16. The interrupt source for interrupts 4−15 can be programmed
by modifying the selector value (binary value) in the corresponding fields of the Interrupt Selector Control
registers: MUXH (address 0x019C0000) and MUXL (address 0x019C0004).
Table 16. C6211/C6211B DSP Interrupts
INTERRUPT
CPU
INTERRUPT
NUMBER
SELECTOR
VALUE
(BINARY)
INTERRUPT
EVENT
SELECTOR
CONTROL
REGISTER
INTERRUPT SOURCE
†
†
†
†
‡
‡
‡
‡
‡
‡
‡
INT_00
INT_01
INT_02
INT_03
INT_04
INT_05
INT_06
INT_07
INT_08
INT_09
INT_10
−
−
−
RESET
NMI
−
−
−
Reserved
Reserved
EXT_INT4
EXT_INT5
EXT_INT6
EXT_INT7
EDMA_INT
Reserved
SD_INT
Reserved
Reserved
DSP_INT
TINT0
Reserved. Do not use.
−
−
Reserved. Do not use.
MUXL[4:0]
MUXL[9:5]
MUXL[14:10]
MUXL[20:16]
MUXL[25:21]
MUXL[30:26]
MUXH[4:0]
MUXH[9:5]
MUXH[14:10]
MUXH[20:16]
MUXH[25:21]
MUXH[30:26]
−
00100
00101
00110
00111
01000
01001
00011
01010
01011
00000
00001
00010
01100
01101
01110
01111
10000 − 11111
External interrupt pin 4
External interrupt pin 5
External interrupt pin 6
External interrupt pin 7
EDMA channel (0 through 15) interrupt
None, but programmable
EMIF SDRAM timer interrupt
None, but programmable
None, but programmable
Host-port interface (HPI)-to-DSP interrupt
Timer 0 interrupt
‡
INT_11
‡
‡
‡
‡
INT_12
INT_13
INT_14
INT_15
TINT1
Timer 1 interrupt
−
−
−
−
−
XINT0
McBSP0 transmit interrupt
McBSP0 receive interrupt
McBSP1 transmit interrupt
McBSP1 receive interrupt
Reserved. Do not use.
−
RINT0
−
XINT1
−
RINT1
−
Reserved
†
‡
Interrupts INT_00 through INT_03 are non-maskable and fixed.
Interrupts INT_04 through INT_15 are programmable by modifying the binary selector values in the Interrupt Selector Control
registers fields. Table 16 shows the default interrupt sources for Interrupts INT_04 through INT_15. For more detailed
information on interrupt sources and selection, see the TMS320C6000 DSP Interrupt Selector Reference Guide (literature
number SPRU646).
19
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
signal groups description
CLKIN
CLKOUT2
RESET
NMI
CLKOUT1
EXT_INT7
EXT_INT6
EXT_INT5
EXT_INT4
Reset and
Interrupts
CLKMODE0
Clock/PLL
PLLV
PLLG
PLLF
TMS
TDO
TDI
RSV5
RSV4
RSV3
RSV2
RSV1
RSV0
TCK
IEEE Standard
1149.1
(JTAG)
Emulation
TRST
EMU0
EMU1
EMU2
EMU3
EMU4
EMU5
Reserved
Control/Status
HPI
16
(Host-Port Interface)
HD[15:0]
Data
HAS
HCNTL0
HCNTL1
HR/W
HCS
HDS1
HDS2
HRDY
HINT
Register Select
Control
Half-Word
Select
HHWIL
Figure 2. CPU (DSP Core) and Peripheral Signals
20
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
signal groups description (continued)
32
ED[31:0]
Data
ECLKIN
ECLKOUT
Memory
Control
ARE/SDCAS/SSADS
CE3
CE2
CE1
CE0
AOE/SDRAS/SSOE
AWE/SDWE/SSWE
ARDY
Memory Map
Space Select
20
EA[21:2]
Address
HOLD
HOLDA
Bus
Arbitration
BE3
BE2
BE1
BE0
BUSREQ
Byte Enables
EMIF
(External Memory Interface)
TOUT1
TINP1
TOUT0
TINP0
Timer 1
Timer 0
Timers
McBSP1
Transmit
McBSP0
Transmit
CLKX1
FSX1
DX1
CLKX0
FSX0
DX0
CLKR1
FSR1
DR1
CLKR0
FSR0
DR0
Receive
Clock
Receive
Clock
CLKS1
CLKS0
McBSPs
(Multichannel Buffered Serial Ports)
Figure 3. Peripheral Signals
21
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions
SIGNAL
NAME
IPD/
IPU
†
DESCRIPTION
TYPE
‡
NO.
A3
CLOCK/PLL
CLKIN
I
IPD
IPD
Clock Input
Clock output at device speed
The CLK1EN bit in the EMIF GBLCTL register controls the CLKOUT1 pin.
CLKOUT1
D7
O
CLK1EN = 0:
CLK1EN = 1:
CLKOUT1 is disabled
CLKOUT1 enabled to clock [default]
Clock output at half of device speed
When the CLKOUT2 pin is enabled, the CLK2EN bit in the EMIF global control register
(GBLCTL) controls the CLKOUT2 pin.
CLKOUT2
Y12
C4
O
I
IPD
IPU
CLK2EN = 0:
CLK2EN = 1:
CLKOUT2 is disabled
CLKOUT1 enabled to clock [default]
Clock mode select
CLKMODE0
•
Selects whether the CPU clock frequency = input clock frequency x4 or x1
§
¶
A
¶
A
¶
A
PLLV
A4
C6
B5
PLL analog V
connection for the low-pass filter
CC
§
PLLG
PLL analog GND connection for the low-pass filter
PLL low-pass filter connection to external components and a bypass capacitor
JTAG EMULATION
PLLF
TMS
TDO
TDI
B7
A8
I
IPU
IPU
IPU
IPU
IPD
IPU
IPU
IPU
IPU
IPU
IPU
JTAG test-port mode select
O/Z
JTAG test-port data out
A7
I
I
I
JTAG test-port data in
TCK
A6
JTAG test-port clock
TRST
EMU5
EMU4
EMU3
EMU2
EMU1
EMU0
B6
JTAG test-port reset
B12
C11
B10
D10
B9
I/O/Z
I/O/Z
I/O/Z
I/O/Z
I/O/Z
I/O/Z
Emulation pin 5. Reserved for future use, leave unconnected.
Emulation pin 4. Reserved for future use, leave unconnected.
Emulation pin 3. Reserved for future use, leave unconnected.
Emulation pin 2. Reserved for future use, leave unconnected.
#
Emulation pin 1
Emulation pin 0
#
D9
RESETS AND INTERRUPTS
Device reset
Nonmaskable interrupt
Edge-driven (rising edge)
Any noise on the NMI pin may trigger an NMI interrupt; therefore, if the NMI pin is not used, it is
recommended that the NMI pin be grounded versus relying on the IPD.
RESET
NMI
A13
C13
I
I
IPU
IPD
•
EXT_INT7
EXT_INT6
EXT_INT5
EXT_INT4
E3
D2
C1
C2
External interrupts
•
•
Edge-driven
I
IPU
Polarity independently selected via the External Interrupt Polarity Register bits
(EXTPOL.[3:0])
HOST-PORT INTERFACE (HPI)
HINT
J20
G19
G18
H20
G20
O
I
IPU
IPU
IPU
IPU
IPU
Host interrupt (from DSP to host)
HCNTL1
HCNTL0
HHWIL
HR/W
Host control − selects between control, address, or data registers
Host control − selects between control, address, or data registers
Host half-word select − first or second half-word (not necessarily high or low order)
Host read or write select
I
I
I
†
‡
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
22
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
§
PLLV and PLLG are not part of external voltage supply or ground. See the CLOCK/PLL documentation for information on how to connect these
pins.
¶
#
A = Analog signal (PLL Filter)
The EMU0 and EMU1 pins are internally pulled up with 30-kΩ resistors; therefore, for emulation and normal operation, no external
pullup/pulldown resistors are necessary. However, for boundary scan operation, pull down the EMU1 and EMU0 pins with a dedicated 1-kΩ
resistor.
Terminal Functions (Continued)
SIGNAL
NAME
IPD/
IPU‡
†
TYPE
DESCRIPTION
HOST-PORT INTERFACE (HPI) (CONTINUED)
NO.
HD15
B14
C14
A15
C15
A16
B16
C16
B17
A18
C17
B18
C19
C20
D18
D20
E20
E18
F20
E19
F18
H19
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPD
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPU
IPD
HD14
HD13
HD12
HD11
HD10
HD9
Host-port data
•
•
Used for transfer of data, address, and control
Also controls initialization of DSP modes at reset via pullup/pulldown resistors
− Device Endian mode
HD8: 0 – Big Endian
HD8
I/O/Z
1 − Little Endian
HD7
− Boot mode
HD[4:3]: 00 – HPI boot
01 − 8-bit ROM boot with default timings
HD6
HD5
10 − 16-bit ROM boot with default timings
11 − 32-bit ROM boot with default timings
HD4
HD3
HD2
HD1
HD0
HAS
HCS
HDS1
HDS2
HRDY
I
I
Host address strobe
Host chip select
I
Host data strobe 1
I
Host data strobe 2
O
Host ready (from DSP to host)
EMIF − CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY
CE3
CE2
CE1
CE0
BE3
BE2
BE1
BE0
V6
W6
W18
V17
V5
O/Z
O/Z
O/Z
O/Z
O/Z
O/Z
O/Z
O/Z
IPU
Memory space enables
IPU
•
•
Enabled by bits 28 through 31 of the word address
Only one asserted during any external data access
IPU
IPU
IPU
IPU
IPU
IPU
Byte-enable control
Y4
•
•
•
Decoded from the two lowest bits of the internal address
Byte-write enables for most types of memory
Can be directly connected to SDRAM read and write mask signal (SDQM)
U19
V20
†
‡
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
23
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions (Continued)
SIGNAL
IPD/
†
TYPE
DESCRIPTION
‡
IPU
NAME
NO.
EMIF − BUS ARBITRATION
Hold-request-acknowledge to the host
Hold request from the host
HOLDA
J18
J17
J19
O
I
IPU
IPU
IPU
HOLD
BUSREQ
O
Bus request output
EMIF − ASYNCHRONOUS/SYNCHRONOUS DRAM/SYNCHRONOUS BURST SRAM MEMORY CONTROL
ECLKIN
Y11
Y10
I
IPD
IPD
EMIF input clock
ECLKOUT
O
EMIF output clock (based on ECLKIN)
ARE/SDCAS/
SSADS
V11
O/Z
O/Z
IPU
IPU
Asynchronous memory read enable/SDRAM column-address strobe/SBSRAM address strobe
Asynchronous memory output enable/SDRAM row-address strobe/SBSRAM output enable
Asynchronous memory write enable/SDRAM write enable/SBSRAM write enable
AOE/SDRAS/
SSOE
W10
AWE/SDWE/
SSWE
V12
Y5
O/Z
I
IPU
IPU
ARDY
Asynchronous memory ready input
EMIF − ADDRESS
EA21
EA20
EA19
EA18
EA17
EA16
EA15
EA14
EA13
EA12
EA11
EA10
EA9
U18
Y18
W17
Y16
V16
Y15
W15
Y14
W14
V14
W13
V10
Y9
O/Z
IPU
EMIF external address
EA8
V9
EA7
Y8
EA6
W8
V8
EA5
EA4
W7
V7
EA3
EA2
Y6
†
‡
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
24
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions (Continued)
SIGNAL
NAME
IPD/
IPU‡
†
TYPE
DESCRIPTION
NO.
EMIF − DATA
ED31
N3
P3
ED30
ED29
ED28
ED27
ED26
ED25
ED24
ED23
ED22
ED21
ED20
ED19
ED18
ED17
ED16
ED15
ED14
ED13
ED12
ED11
ED10
ED9
P2
P1
R2
R3
T2
T1
U3
U1
U2
V1
V2
Y3
W4
V4
I/O/Z
IPU
External data
T19
T20
T18
R20
R19
P20
P18
N20
N19
N18
M20
M19
L19
L18
K19
K18
ED8
ED7
ED6
ED5
ED4
ED3
ED2
ED1
ED0
†
‡
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
25
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions (Continued)
SIGNAL
NAME
IPD/
IPU‡
†
TYPE
DESCRIPTION
NO.
TIMER 1
Timer 1 or general-purpose output
Timer 1 or general-purpose input
TIMER 0
TOUT1
F1
F2
O
I
IPD
IPD
TINP1
TOUT0
TINP0
G1
G2
O
I
IPD
IPD
Timer 0 or general-purpose output
Timer 0 or general-purpose input
MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1)
CLKS1
CLKR1
CLKX1
DR1
E1
M1
L3
I
IPD
IPD
IPD
IPU
IPU
IPD
IPD
External clock source (as opposed to internal)
Receive clock
I/O/Z
I/O/Z
I
Transmit clock
M2
L2
Receive data
DX1
O/Z
I/O/Z
I/O/Z
Transmit data
FSR1
FSX1
M3
L1
Receive frame sync
Transmit frame sync
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP0)
CLKS0
CLKR0
CLKX0
DR0
K3
H3
G3
J1
I
IPD
IPD
IPD
IPU
IPU
IPD
IPD
External clock source (as opposed to internal)
Receive clock
I/O/Z
I/O/Z
I
Transmit clock
Receive data
DX0
H2
J3
O/Z
I/O/Z
I/O/Z
Transmit data
FSR0
FSX0
Receive frame sync
H1
Transmit frame sync
RESERVED FOR TEST
RSV0
RSV1
RSV2
RSV3
RSV4
RSV5
C12
D12
A5
O
O
O
O
O
O
IPU
IPU
IPU
Reserved (leave unconnected, do not connect to power or ground)
Reserved (leave unconnected, do not connect to power or ground)
Reserved (leave unconnected, do not connect to power or ground)
Reserved (leave unconnected, do not connect to power or ground)
Reserved (leave unconnected, do not connect to power or ground)
Reserved (leave unconnected, do not connect to power or ground)
D3
N2
Y20
†
‡
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
26
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions (Continued)
SIGNAL
NAME
†
TYPE
DESCRIPTION
SUPPLY VOLTAGE PINS
NO.
A17
B3
B8
B13
C5
C10
D1
D16
D19
F3
H18
J2
M18
N1
R1
DV
S
3.3-V supply voltage
DD
R18
T3
U5
U7
U12
U16
V13
V15
V19
W3
W9
W12
Y7
Y17
A9
A10
A12
B2
B19
C3
CV
S
1.8-V supply voltage
DD
C7
C18
D5
D6
D11
D14
†
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
27
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions (Continued)
SIGNAL
†
TYPE
DESCRIPTION
SUPPLY VOLTAGE PINS (CONTINUED)
NAME
NO.
D15
F4
F17
K1
K4
K17
L4
L17
L20
R4
CV
S
1.8-V supply voltage
DD
R17
U6
U10
U11
U14
U15
V3
V18
W2
W19
GROUND PINS
A1
A2
A11
A14
A19
A20
B1
B4
B11
B15
B20
C8
V
SS
GND
Ground pins
C9
D4
D8
D13
D17
E2
†
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
28
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Terminal Functions (Continued)
SIGNAL
NAME
†
TYPE
DESCRIPTION
GROUND PINS (CONTINUED)
NO.
E4
E17
F19
G4
G17
H4
H17
J4
K2
K20
M4
M17
N4
N17
P4
P17
P19
T4
V
SS
GND
Ground pins
T17
U4
U8
U9
U13
U17
U20
W1
W5
W11
W16
W20
Y1
Y2
Y13
Y19
†
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
29
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
development support
TI offers an extensive line of development tools for the TMS320C6000 DSP platform, including tools to
evaluate the performance of the processors, generate code, develop algorithm implementations, and fully
integrate and debug software and hardware modules.
The following products support development of C6000 DSP-based applications:
Software Development Tools:
Code Composer Studio Integrated Development Environment (IDE): including Editor
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS), which provides the basic run-time target software
needed to support any DSP application.
Hardware Development Tools:
Extended Development System (XDS) Emulator (supports C6000 DSP multiprocessor system debug)
EVM (Evaluation Module)
For a complete listing of development-support tools for the TMS320C6000 DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL) and select
“Find Development Tools”. For device-specific tools, under “Semiconductor Products”, select “Digital Signal
Processors”, choose a product family, and select the particular DSP device. For information on pricing and
availability, contact the nearest TI field sales office or authorized distributor.
Code Composer Studio, DSP/BIOS, and XDS are trademarks of Texas Instruments.
30
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
device and development-support tool nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all DSP
devices and support tools. Each DSP commercial family member has one of three prefixes: TMX, TMP, or
TMS (e.g., TMS320C6211GFN167). Texas Instruments recommends two of three possible prefix designators
for support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development
from engineering prototypes (TMX/TMDX) through fully qualified production devices/tools (TMS/TMDS).
Device development evolutionary flow:
TMX Experimental device that is not necessarily representative of the final device’s electrical specifications
TMP Final silicon die that conforms to the device’s electrical specifications but has not completed quality
and reliability verification
TMS Fully qualified production device
Support tool development evolutionary flow:
TMDX Development-support product that has not yet completed Texas Instruments internal qualification
testing.
TMDS Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped with the following disclaimer:
“Developmental product is intended for internal evaluation purposes.”
TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI’s standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, GFN), the temperature range (for example, blank is the default commercial temperature range),
and the device speed range in megahertz (for example, -167 is 167 MHz).
The ZFN package, like the GFN package, is a 256-ball plastic BGA only with Pb-free balls. For device part
numbers and further ordering information for TMS320C6211/6211B in the GFN and ZFN, package types, see
the TI website (http://www.ti.com) or contact your TI sales representative.
TMS320 is a trademark of Texas Instruments.
31
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
device and development-support tool nomenclature (continued)
(
)
TMS 320
C
6211 GFN
167
PREFIX
DEVICE SPEED RANGE
TMX= Experimental device
TMP= Prototype device
100 MHz
120 MHz
150 MHz
167 MHz
200 MHz
233 MHz
250 MHz
300 MHz
TMS= Qualified device
SMJ = MIL-PRF-38535, QML
SM = High Rel (non-38535)
TEMPERATURE RANGE (DEFAULT: 0°C TO 90°C)
Blank = 0°C to 90°C, commercial temperature
A
= −40°C to 105°C, extended temperature
DEVICE FAMILY
32 or 320 = TMS320 DSP family
†‡
PACKAGE TYPE
GDP = 272-pin plastic BGA
GFN = 256-pin plastic BGA
TECHNOLOGY
GGP = 352-pin plastic BGA
C = CMOS
GJC = 352-pin plastic BGA
GJL = 352-pin plastic BGA
GLS = 384-pin plastic BGA
GLW = 340-pin plastic BGA
GNY = 384-pin plastic BGA
GNZ = 352-pin plastic BGA
GLZ = 532-pin plastic BGA
GHK = 288-pin plastic MicroStar BGAt
PYP = 208-pin PowerPADt plastic QFP
ZFN = 256-pin plastic BGA, with Pb-free soldered balls
§
DEVICE
C6000 DSPs:
C6201
C6211B DM641 C6712
C6202
C6411
DM642 C6712C
C6202B C6412
C6203B C6414
C6204
C6205
C6211
C6701
C6711
C6712D
C6713
C6415
C6416
C6711B C6713B
C6711C
DM640 C6711D
†
BGA
QFP
=
=
Ball Grid Array
Quad Flatpack
‡
§
The ZFN mechanical package designator represents the version of the GFN with Pb−Free soldered balls.
For actual device part numbers (P/Ns) and ordering information, see the Mechanical Data section of this
document or the TI website (www.ti.com).
Figure 4. TMS320C6000 DSP Device Nomenclature (Including the TMS320C6211
and TMS320C6211B Devices)
MicroStar BGA is a trademark of Texas Instruments.
32
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
documentation support
Extensive documentation supports all TMS320 DSP family generations of devices from product
announcement through applications development. The types of documentation available include: data sheets,
such as this document, with design specifications; complete user’s reference guides for all devices and tools;
technical briefs; development-support tools; on-line help; and hardware and software applications. The
following is a brief, descriptive list of support documentation specific to the C6000 DSP devices:
For device-specific datasheets and related documentation, visit the TI web site at: http://www.ti.com.
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189) describes the
C6000 CPU (DSP core) architecture, instruction set, pipeline, and associated interrupts.
The TMS320C6000 DSP Peripherals Overview Reference Guide (literature number SPRU190) provides an
overview and briefly describes the functionality of the peripherals available on the C6000 DSP platform of
devices. This document also includes a table listing the peripherals available on the C6000 devices along with
literature numbers and hyperlinks to the associated peripheral documents.
The TMS320C6000 Technical Brief (literature number SPRU197) gives an introduction to the
TMS320C62x/TMS320C67x devices, associated development tools, and third-party support.
The TMS320C6000 DSP Interrupt Selector Reference Guide (literature number SPRU646) describes the
interrupt selector, interrupt selector registers, and the available interrupts in the TMS320C6000 DSPs.
The TMS320C6000 DSP Enhanced Direct Memory Access (EDMA) Controller Reference Guide (literature
number SPRU234) describes the operation of the enhanced direct memory access (EDMA) controller in the
TMS320C6000 DSPs.
The TMS320C62x/C67x Power Consumption Summary application report (literature number SPRA486)
discusses the power consumption for user applications with the TMS320C6211 and TMS320C6211B DSP
devices.
The TMS320C6211/TMS320C6211B Digital Signal Processors Silicon Errata (literature number SPRZ154)
describes the known exceptions to the functional specifications for the TMS320C6211 and TMS320C6211B
DSP devices.
The Using IBIS Models for Timing Analysis application report (literature number SPRA839) describes how to
properly use IBIS models to attain accurate timing analysis for a given system.
The tools support documentation is electronically available within the Code Composer Studio Integrated
Development Environment (IDE). For a complete listing of C6000 DSP latest documentation, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL).
See the Worldwide Web URL for the application reports How To Begin Development Today with the
TMS320C6211 DSP (literature number SPRA474) and How To Begin Development with the TMS320C6711
DSP (literature number SPRA522), which describe in more detail the similarities/differences between the C6211
and C6711 C6000 DSP devices.
TMS320C67x is a trademark of Texas Instruments.
33
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
clock PLL
All of the internal C62x clocks are generated from a single source through the CLKIN pin. This source clock
either drives the PLL, which multiplies the source clock in frequency to generate the internal CPU clock, or
bypasses the PLL to become the internal CPU clock.
To use the PLL to generate the CPU clock, the external PLL filter circuit must be properly designed. Figure 5
shows the external PLL circuitry for either x1 (PLL bypass) or x4 PLL multiply modes. Figure 6 shows the
external PLL circuitry for a system with ONLY x1 (PLL bypass) mode.
To minimize the clock jitter, a single clean power supply should power both the C62x device and the external
clock oscillator circuit. Noise coupling into PLLF will directly impact PLL clock jitter. The minimum CLKIN rise
and fall times should also be observed. For the input clock timing requirements, see the input and output clocks
electricals section.
Rise/fall times, duty cycles (high/low pulse durations), and the load capacitance of the external clock source
must meet the DSP requirements in this data sheet (see the electrical characteristics over recommended
ranges of suppy voltage and operating case temperature table and the input and output clocks electricals
section). Table 17 lists some examples of compatible CLKIN external clock sources.
Table 17. Compatible CLKIN External Clock Sources
COMPATIBLE PARTS FOR
EXTERNAL CLOCK SOURCES (CLKIN)
PART NUMBER
MANUFACTURER
JITO-2
STA series, ST4100 series
SG-636
Fox Electronix
SaRonix Corporation
Epson America
Oscillators
342
Corning Frequency Control
Integrated Circuit Systems
PLL
MK1711-S, ICS525-02
3.3V
PLLV
Internal to
PLL
C6211/C6211B
CLKMODE0
PLLMULT
CLKIN
C4
C3
PLLCLK
0.1 mF
10 mF
CLKIN
1
0
CPU
CLOCK
LOOP FILTER
Available Multiply Factors
CPU Clock
Frequency
f(CPUCLOCK)
PLL Multiply
Factors
C2
CLKMODE0
(For C1, C2, and R1 values, see Table 18.)
0
1
x1(BYPASS)
x4
1 x f(CLKIN)
4 x f(CLKIN)
C1
R1
NOTES: A. Keep the lead length and the number of vias between the PLLF pin, the PLLG pin, and R1, C1, and C2 to a minimum. In addition,
place all PLL external components (R1, C1, C2, C3, C4, and the EMI Filter) as close to the C6000 device as possible. For the best
performance, TI recommends that all the PLL external components be on a single side of the board without jumpers, switches, or
components other than the ones shown.
B. For reduced PLL jitter, maximize the spacing between switching signals and the PLL external components (R1, C1, C2, C3, C4,
and the EMI filter).
C. The 3.3-V supply for the EMI filter must be from the same 3.3-V power plane supplying the I/O voltage, DV
D. EMI filter manufacturer: TDK part number ACF451832-333, 223, 153, 103. Panasonic part number EXCCET103U.
.
DD
Figure 5. External PLL Circuitry for Either PLL x4 Mode or x1 (Bypass) Mode
34
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
clock PLL (continued)
3.3V
PLLV
Internal to
PLL
C6211/C6211B
CLKMODE0
CLKIN
PLLMULT
CLKIN
PLLCLK
1
0
LOOP FILTER
CPU
CLOCK
NOTES: A. For a system with ONLY PLL x1 (bypass) mode, short the PLLF terminal to the PLLG terminal.
B. The 3.3-V supply for the EMI filter must be from the same 3.3-V power plane supplying the I/O voltage, DV
.
DD
Figure 6. External PLL Circuitry for x1 (Bypass) Mode Only
Table 18. C6211/C6211B PLL Component Selection
CPU CLOCK
FREQUENCY
(CLKOUT1)
CLKIN
RANGE
(MHz)
CLKOUT2
RANGE
(MHz)
TYPICAL
R1 [ 1%]
C1 [ 10%]
(nF)
C2 [ 10%]
CLKMODE
LOCK TIME
(Ω)
(pF)
†
(µs)
RANGE (MHz)
x4
16.3−41.6
65−167
32.5−83
60.4
27
560
75
†
Under some operating conditions, the maximum PLL lock time may vary as much as 150% from the specified typical value. For example, if the
typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.
35
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
power-down mode logic
Figure 7 shows the power-down mode logic on the C6211/C6211B.
CLKOUT1
CLKOUT2
Internal Clock Tree
Clock
Distribution
and Dividers
PD1
PD2
IFR
Power-
Down
Logic
Clock
PLL
Internal
Peripherals
IER
CSR
PWRD
CPU
PD3
TMS320C6211/C6211B
CLKIN
RESET
†
External input clocks, with the exception of CLKIN, are not gated by the power-down mode logic.
†
Figure 7. Power-Down Mode Logic
triggering, wake-up, and effects
The power-down modes and their wake-up methods are programmed by setting the PWRD field (bits 15−10)
of the control status register (CSR). The PWRD field of the CSR is shown in Figure 8 and described in Table 19.
When writing to the CSR, all bits of the PWRD field should be set at the same time. Logic 0 should be used when
“writing” to the reserved bit (bit 15) of the PWRD field. The CSR is discussed in detail in the TMS320C6000 CPU
and Instruction Set Reference Guide (literature number SPRU189).
36
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
31
16
15
14
13
12
11
PD2
R/W-0
10
9
8
0
Enable or
Non-Enabled
Interrupt Wake
Enabled
Interrupt Wake
Reserved
R/W-0
PD3
PD1
R/W-0
R/W-0
R/W-0
R/W-0
7
Legend: R/W−x = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Figure 8. PWRD Field of the CSR Register
A delay of up to nine clock cycles may occur after the instruction that sets the PWRD bits in the CSR before the
PD mode takes effect. As best practice, NOPs should be padded after the PWRD bits are set in the CSR to account
for this delay.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where
PD1 took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine with be executed
first, then the program execution returns to the instruction where PD1 took effect. In the case with an enabled
interrupt, the GIE bit in the CSR and the NMIE bit in the interrupt enable register (IER) must also be set in order
for the interrupt service routine to execute; otherwise, execution returns to the instruction where PD1 took effect
upon PD1 mode termination by an enabled interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 19 summarizes all the power-down modes.
37
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
Table 19. Characteristics of the Power-Down Modes
PRWD FIELD
(BITS 15−10)
POWER-DOWN
WAKE-UP METHOD
—
EFFECT ON CHIP’S OPERATION
MODE
000000
001001
No power-down
—
CPU halted (except for the interrupt logic)
PD1
Wake by an enabled interrupt
Power-down mode blocks the internal clock inputs at the
boundary of the CPU, preventing most of the CPU’s logic from
switching. During PD1, EDMA transactions can proceed
between peripherals and internal memory.
Wake by an enabled or
non-enabled interrupt
010001
011010
PD1
Output clock from PLL is halted, stopping the internal clock
structure from switching and resulting in the entire chip being
halted. All register and internal RAM contents are preserved. All
functional I/O “freeze” in the last state when the PLL clock is
turned off.
†
PD2
Wake by a device reset
Input clock to the PLL stops generating clocks. All register and
internal RAM contents are preserved. All functional I/O “freeze” in
the last state when the PLL clock is turned off. Following reset, the
PLL needs time to re-lock, just as it does following power-up.
Wake-up from PD3 takes longer than wake-up from PD2 because
the PLL needs to be re-locked, just as it does following power-up.
†
PD3
011100
Wake by a device reset
All others
Reserved
—
—
†
When entering PD2 and PD3, all functional I/O remains in the previous state. However, for peripherals which are asynchronous in nature or
peripherals with an external clock source, output signals may transition in response to stimulus on the inputs. Under these conditions,
peripherals will not operate according to specifications.
38
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
power-supply sequencing
TI DSPs do not require specific power sequencing between the core supply and the I/O supply. However,
systems should be designed to ensure that neither supply is powered up for extended periods of time if the other
supply is below the proper operating voltage.
system-level design considerations
System-level design considerations, such as bus contention, may require supply sequencing to be
implemented. In this case, the core supply should be powered up at the same time as, or prior to (and powered
down after), the I/O buffers. This is to ensure that the I/O buffers receive valid inputs from the core before the
output buffers are powered up, thus, preventing bus contention with other chips on the board.
power-supply design considerations
For systems using the C6000 DSP platform of devices, the core supply may be required to provide in excess
of 2 A per DSP until the I/O supply is powered up. This extra current condition is a result of uninitialized logic
within the DSP(s) and is corrected once the CPU sees an internal clock pulse. With the PLL enabled, as the
I/O supply is powered on, a clock pulse is produced stopping the extra current draw from the supply. With the
PLL disabled, as many as five external clock cycle pulses may be required to stop this extra current draw. A
normal current state returns once the I/O power supply is turned on and the CPU sees a clock pulse. Decreasing
the amount of time between the core supply power up and the I/O supply power up can minimize the effects
of this current draw.
A dual-power supply with simultaneous sequencing, such as available with TPS563xx controllers or PT69xx
plug-in power modules, can be used to eliminate the delay between core and I/O power up [see the Using the
TPS56300 to Power DSPs application report (literature number SLVA088)]. A Schottky diode can also be used
to tie the core rail to the I/O rail, effectively pulling up the I/O power supply to a level that can help initialize the
logic within the DSP.
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C6000 platform of DSPs, the PC board should include separate power planes for
core, I/O, and ground, all bypassed with high-quality low-ESL/ESR capacitors.
39
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
IEEE 1149.1 JTAG compatibility statement
The TMS320C6211/C6211B DSP requires that both TRST and RESET resets be asserted upon power up to
be properly initialized. While RESET initializes the DSP core, TRST initializes the DSP’s emulation logic. Both
resets are required for proper operation.
While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the
DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface
and DSP’s emulation logic in the reset state.
TRST only needs to be released when it is necessary to use a JTAG controller to debug the DSP or exercise
the DSP’s boundary scan functionality.
For maximum reliability, the TMS320C6211/C6211B DSP includes an internal pulldown (IPD) on the TRST pin
to ensure that TRST will always be asserted upon power up and the DSP’s internal emulation logic will always
be properly initialized.
JTAG controllers from Texas Instruments actively drive TRST high. However, some third-party JTAG controllers
may not drive TRST high but expect the use of an external pullup resistor on TRST.
When using this type of JTAG controller, assert TRST to initialize the DSP after powerup and externally drive
TRST high before attempting any emulation or boundary scan operations. Following the release of RESET, the
low-to-high transition of TRST must be “seen” to latch the state of EMU1 and EMU0. The EMU[1:0] pins
configure the device for either Boundary Scan mode or Emulation mode. For more detailed information, see
the terminal functions section of this data sheet.
EMIF device speed
TI recommends utilizing the input/output buffer information specification (IBIS) models to analyze all AC timings.
To properly use IBIS models to attain accurate timing analysis for a given system, see the Using IBIS Models
for Timing Analysis application report (literature number SPRA839).
40
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
bootmode
The C62x device resets using the active-low signal RESET signal (for the C6211/C6211B device, the RESET
signal is the same as the internal reset signal). While RESET is low, the internal reset is also asserted and the
device is held in reset and is initialized to the prescribed reset state. Refer to reset timing for reset timing
characteristics and states of device pins during reset. The release of the internal reset signal (see the Reset
Phase 3 discussion in the Reset Timing section of this data sheet) starts the processor running with the
prescribed device configuration and boot mode.
The C6211/C6211B has three types of boot modes:
D
Host boot
If host boot is selected, upon release of internal reset, the CPU is internally “stalled” while the remainder of
the device is released. During this period, an external host can initialize the CPU’s memory space as
necessary through the host interface, including internal configuration registers, such as those that control
the EMIF or other peripherals. Once the host is finished with all necessary initialization, it must set the
DSPINT bit in the HPIC register to complete the boot process. This transition causes the boot configuration
logic to bring the CPU out of the “stalled” state. The CPU then begins execution from address 0. The DSPINT
condition is not latched by the CPU, because it occurs while the CPU is still internally “stalled”. Also, DSPINT
brings the CPU out of the “stalled” state only if the host boot process is selected. All memory may be written
to and read by the host. This allows for the host to verify what it sends to the DSP if required. After the CPU is
out of the “stalled” state, the CPU needs to clear the DSPINT, otherwise, no more DSPINTs can be received.
D
D
Emulation boot
Emulation boot mode is a variation of host boot. In this mode, it is not necessary for a host to load code or to
set DSPINT to release the CPU from the “stalled” state. Instead, the emulator will set DSPINT if it has not
been previously set so that the CPU can begin executing code from address 0. Prior to beginning execution,
the emulator sets a breakpoint at address 0. This prevents the execution of invalid code by halting the CPU
prior to executing the first instruction. Emulation boot is a good tool in the debug phase of development.
EMIF boot (using default ROM timings)
Upon the release of internal reset, the 1K-Byte ROM code located in the beginning of CE1 is copied to
address 0 by the EDMA using the default ROM timings, while the CPU is internally “stalled”. The data should
be stored in the endian format that the system is using. The boot process also lets you choose the width of
the ROM. In this case, the EMIF automatically assembles consecutive 8-bit bytes or 16-bit half-words to
form the 32-bit instruction words to be copied. The transfer is automatically done by the EDMA as a
single-frame block transfer from the ROM to address 0. After completion of the block transfer, the CPU is
released from the “stalled” state and start running from address 0.
41
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
†
absolute maximum ratings over operating case temperature range (unless otherwise noted)
Supply voltage range, CV
Supply voltage range, DV
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.3 V to 2.3 V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
DD
DD
Input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Operating case temperature ranges, T :(default) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0_C to 90_C
C
(A version) [C6211BGFNA only] . . . . . . . . . . . . . . −40_C to105_C
Storage temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65_C to 150_C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to V
SS
.
recommended operating conditions
MIN NOM
MAX UNIT
CV
DV
Supply voltage, Core
Supply voltage, I/O
Supply ground
1.71
3.14
0
1.8
3.3
0
1.89
3.46
0
V
V
DD
DD
V
V
V
V
SS
High-level input voltage
Low-level input voltage
2
V
IH
IL
0.8
−4
−8
4
V
All signals except CLKOUT1, CLKOUT2, and ECLKOUT
CLKOUT1, CLKOUT2, and ECLKOUT
All signals except CLKOUT1, CLKOUT2, and ECLKOUT
CLKOUT1, CLKOUT2, and ECLKOUT
Default
mA
mA
mA
mA
_C
_C
I
I
High-level output current
Low-level output current
Operating case temperature
OH
OL
8
0
90
105
T
C
A version (C6211BGFNA only)
−40
electrical characteristics over recommended ranges of supply voltage and operating case
temperature (unless otherwise noted)
‡
PARAMETER
High-level output voltage
Low-level output voltage
Input current
TEST CONDITIONS
MIN
TYP
MAX
UNIT
V
V
V
DV
DV
= MIN,
= MIN,
I
= MAX
= MAX
2.4
OH
DD
DD
OH
OL
I
0.4
150
10
V
OL
I
I
V = V
I SS
to DV
DD
uA
uA
mA
mA
mA
mA
mA
mA
pF
I
Off-state output current
V
= DV
or 0 V
= NOM, CPU clock = 150 MHz
= NOM, CPU clock = 150 MHz
= NOM, CPU clock = 150 MHz
OZ
O DD
C6211, CV
DD
270
270
220
220
60
Supply current, CPU + CPU memory
I
I
I
DD2V
§
access
C6211B, CV
DD
C6211, CV
DD
§
Supply current, peripherals
DD2V
DD3V
C6211B, CV
= NOM, CPU clock = 150 MHz
= NOM, CPU clock = 150 MHz
DD
C6211, DV
DD
§
Supply current, I/O pins
C6211B, DV
DD
= NOM, CPU clock = 150 MHz
60
C
C
Input capacitance
Output capacitance
7
7
i
pF
o
‡
§
For test conditions shown as MIN, MAX, or NOM, use the appropriate value specified in the recommended operating conditions table.
Measured with average activity (50% high/50% low power). For more details on CPU, peripheral, and I/O activity, refer to the TMS320C62x/C67x
Power Consumption Summary application report (literature number SPRA486).
42
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
PARAMETER MEASUREMENT INFORMATION
I
OL
Tester Pin
Electronics
Output
Under
Test
50 Ω
V
comm
C
T
I
OH
Where:
I
I
V
=
=
=
=
2 mA
2 mA
0.8 V
OL
OH
comm
T
C
10−15-pF typical load-circuit capacitance
Figure 9. Test Load Circuit for AC Timing Measurements
signal transition levels
All input and output timing parameters are referenced to 1.5 V for both “0” and “1” logic levels.
V
ref
= 1.5 V
Figure 10. Input and Output Voltage Reference Levels for ac Timing Measurements
All rise and fall transition timing parameters are referenced to V MAX and V MIN for input clocks, and
IL
IH
V
MAX and V
MIN for output clocks.
OL
OH
V
ref
= V MIN (or V
IH OH
MIN)
V
ref
= V MAX (or V
IL OL
MAX)
Figure 11. Rise and Fall Transition Time Voltage Reference Levels
43
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
timing parameters and board routing analysis
The timing parameter values specified in this data sheet do not include delays by board routings. As a good
board design practice, such delays must always be taken into account. Timing values may be adjusted by
increasing/decreasing such delays. TI recommends utilizing the available I/O buffer information specification
(IBIS) models to analyze the timing characteristics correctly. If needed, external logic hardware such as buffers
may be used to compensate any timing differences. For example:
D
D
In typical boards with the C6211B commercial temperature device, the routing delay improves the external
memory’s ability to meet the DSP’s EMIF data input hold time requirement [t ].
h(EKOH-EDV)
In some boards with the C6211BGFNA extended temperature device, the routing delay improves the
external memory’s ability to meet the DSP’s EMIF data input hold time requirement [t ]. In
h(EKOH-EDV)
addition, it may be necessary to add an extra delay to the input clock of the external memory to robustly
meet the DSP’s data input hold time requirement. If the extra delay approach is used, memory bus
frequency adjustments may be needed to ensure the DPS’s input setup time requirement [t
is still maintained.
]
su(EDV-EKOH)
For inputs, timing is most impacted by the round-trip propagation delay from the DSP to the external device and
from the external device to the DSP. This round-trip delay tends to negatively impact the input setup time margin,
but also tends to improve the input hold time margins (see Table 20 and Figure 12).
Figure 12 represents a general transfer between the DSP and an external device. The figure also represents
board route delays and how they are perceived by the DSP and the external device.
44
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
Table 20. IBIS Timing Parameters Example (see Figure 12)
NO.
1
DESCRIPTION
Clock route delay
2
Minimum DSP hold time
3
Minimum DSP setup time
External device hold time requirement
External device setup time requirement
Control signal route delay
External device hold time
4
5
6
7
8
External device access time
DSP hold time requirement
DSP setup time requirement
Data route delay
9
10
11
ECLKOUT
(Output from DSP)
1
ECLKOUT
(Input to External Device)
2
3
†
Control Signals
(Output from DSP)
4
5
6
Control Signals
(Input to External Device)
7
8
‡
Data Signals
(Output from External Device)
9
10
11
‡
Data Signals
(Input to DSP)
† Control signals include data for Writes.
‡ Data signals are generated during Reads from an external device.
Figure 12. IBIS Input/Output Timings
45
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
INPUT AND OUTPUT CLOCKS
†‡
timing requirements for CLKIN (see Figure 13)
−150
CLKMODE = x4 CLKMODE = x1
−167
CLKMODE = x4 CLKMODE = x1
NO.
UNIT
MIN
26.7
0.4C
0.4C
MAX
MIN
6.7
MAX
MIN
24
MAX
MIN
6
MAX
1
2
3
4
t
t
t
t
Cycle time, CLKIN
ns
ns
ns
ns
c(CLKIN)
w(CLKINH)
w(CLKINL)
t(CLKIN)
Pulse duration, CLKIN high
Pulse duration, CLKIN low
Transition time, CLKIN
0.45C
0.45C
0.4C
0.4C
0.45C
0.45C
5
1
5
1
†
‡
The reference points for the rise and fall transitions are measured at V MAX and V MIN.
C = CLKIN cycle time in ns. For example, when CLKIN frequency is 40 MHz, use C = 25 ns.
IL
IH
1
4
2
CLKIN
3
4
Figure 13. CLKIN Timings
46
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
INPUT AND OUTPUT CLOCKS (CONTINUED)
†‡§
switching characteristics over recommended operating conditions for CLKOUT1
(see Figure 14)
−150
−167
NO.
PARAMETER
UNIT
CLKMODE = x4
CLKMODE = x1
MIN
MAX
P + 0.7
MIN
MAX
1
2
3
4
t
t
t
t
Cycle time, CLKOUT1
P − 0.7
P − 0.7
P + 0.7
ns
ns
ns
ns
c(CKO1)
w(CKO1H)
w(CKO1L)
t(CKO1)
Pulse duration, CLKOUT1 high
Pulse duration, CLKOUT1 low
Transition time, CLKOUT1
(P/2) − 0.7 (P/2 ) + 0.7 PH − 0.7 PH + 0.7
(P/2) − 0.7 (P/2 ) + 0.7
2
PL − 0.7 PL + 0.7
2
†
‡
§
The reference points for the rise and fall transitions are measured at V
P = 1/CPU clock frequency in nanoseconds (ns)
PH is the high period of CLKIN in ns and PL is the low period of CLKIN in ns.
MAX and V MIN.
OH
OL
1
4
2
CLKOUT1
3
4
Figure 14. CLKOUT1 Timings
†‡
switching characteristics over recommended operating conditions for CLKOUT2 (see Figure 15)
−150
−167
NO.
PARAMETER
UNIT
MIN
MAX
1
2
3
4
t
t
t
t
Cycle time, CLKOUT2
2P − 0.7 2P + 0.7
ns
ns
ns
ns
c(CKO2)
w(CKO2H)
w(CKO2L)
t(CKO2)
Pulse duration, CLKOUT2 high
Pulse duration, CLKOUT2 low
Transition time, CLKOUT2
P − 0.7
P − 0.7
P + 0.7
P + 0.7
2
†
‡
The reference points for the rise and fall transitions are measured at V
P = 1/CPU clock frequency in ns
MAX and V
MIN.
OL
OH
1
4
2
CLKOUT2
3
4
Figure 15. CLKOUT2 Timings
47
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
INPUT AND OUTPUT CLOCKS (CONTINUED)
†
timing requirements for ECLKIN (see Figure 16)
−150
−167
NO.
UNIT
MIN
MAX
1
2
3
4
t
t
t
t
Cycle time, ECLKIN
10
4.5
4.5
ns
ns
ns
ns
c(EKI)
Pulse duration, ECLKIN high
Pulse duration, ECLKIN low
Transition time, ECLKIN
w(EKIH)
w(EKIL)
t(EKI)
2.2
†
The reference points for the rise and fall transitions are measured at V MAX and V MIN.
IL IH
1
4
2
ECLKIN
3
4
Figure 16. ECLKIN Timings
द
switching characteristics over recommended operating conditions for ECLKOUT
(see Figure 17)
−150
−167
NO.
PARAMETER
UNIT
MIN
E − 0.7
MAX
1
2
3
4
5
6
t
t
t
t
t
t
Cycle time, ECLKOUT
E + 0.7
ns
ns
ns
ns
ns
ns
c(EKO)
Pulse duration, ECLKOUT high
EH − 0.7 EH + 0.7
EL − 0.7 EL + 0.7
2
w(EKOH)
w(EKOL)
Pulse duration, ECLKOUT low
Transition time, ECLKOUT
t(EKO)
Delay time, ECLKIN high to ECLKOUT high
Delay time, ECLKIN low to ECLKOUT low
1
1
7
7
d(EKIH-EKOH)
d(EKIL-EKOL)
‡
§
¶
The reference points for the rise and fall transitions are measured at V
E = ECLKIN period in ns
EH is the high period of ECLKIN in ns and EL is the low period of ECLKIN in ns.
MAX and V MIN.
OH
OL
ECLKIN
6
1
4
4
2
5
3
ECLKOUT
Figure 17. ECLKOUT Timings
48
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
ASYNCHRONOUS MEMORY TIMING
†‡§
timing requirements for asynchronous memory cycles
(see Figure 18−Figure 19)
C6211B−150
C6211−150
C6211B−167
C6211BGFNA−150
C6211−167
NO.
UNIT
MIN MAX
MIN
9
MAX
3
4
6
7
t
t
t
t
Setup time, EDx valid before ARE high
Hold time, EDx valid after ARE high
9
1
3
1
ns
ns
ns
ns
su(EDV-AREH)
h(AREH-EDV)
su(ARDY-EKOH)
h(EKOH-ARDY)
2
Setup time, ARDY valid before ECLKOUT high
Hold time, ARDY valid after ECLKOUT high
3
2
†
To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. The ARDY signal is recognized in
the cycle for which the setup and hold time is met. To use ARDY as an asynchronous input, the pulse width of the ARDY signal should be wide
enough (e.g., pulse width = 2E) to ensure setup and hold time is met.
‡
§
RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
E = ECLKOUT period in ns
switching characteristics over recommended operating conditions for asynchronous memory
द
cycles for C6211 and C6211B
(see Figure 18−Figure 19)
C6211−150
C6211−167
C6211B−150
C6211B−167
NO.
PARAMETER
UNIT
MIN
MAX
MIN
RS * E − 3
RH * E − 3
1.5
MAX
1
2
t
t
t
t
t
t
Output setup time, select signals valid to ARE low
Output hold time, ARE high to select signals invalid
Delay time, ECLKOUT high to ARE vaild
RS * E − 3
ns
ns
ns
ns
ns
ns
osu(SELV-AREL)
oh(AREH-SELIV)
d(EKOH-AREV)
osu(SELV-AWEL)
oh(AWEH-SELIV)
d(EKOH-AWEV)
RH * E − 3
1.5
5
8
8
8
Output setup time, select signals valid to AWE low
Output hold time, AWE high to select signals invalid
Delay time, ECLKOUT high to AWE vaild
WS * E − 3
WH * E − 3
1.5
WS * E − 3
WH * E − 3
1.2
9
10
8
8
‡
RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
E = ECLKOUT period in ns
§
¶
Select signals include: CEx, BE[3:0], EA[21:2], AOE; and for writes, include ED[31:0].
switching characteristics over recommended operating conditions for asynchronous memory
द
cycles for C6211BGFNA
(see Figure 18−Figure 19)
C6211BGFNA−150
NO.
PARAMETER
UNIT
MIN
RS * E − 3
RH * E − 3
1.5
MAX
1
2
t
t
t
t
t
t
Output setup time, select signals valid to ARE low
Output hold time, ARE high to select signals invalid
Delay time, ECLKOUT high to ARE vaild
ns
ns
ns
ns
ns
ns
osu(SELV-AREL)
oh(AREH-SELIV)
d(EKOH-AREV)
osu(SELV-AWEL)
oh(AWEH-SELIV)
d(EKOH-AWEV)
5
8
8
Output setup time, select signals valid to AWE low
Output hold time, AWE high to select signals invalid
Delay time, ECLKOUT high to AWE vaild
WS * E − 3
WH * E − 3
1
9
10
8
‡
RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
§
¶
E = ECLKOUT period in ns
Select signals include: CEx, BE[3:0], EA[21:2], AOE; and for writes, include ED[31:0].
49
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Strobe = 3
Not Ready
Hold = 2
ECLKOUT
CEx
1
1
1
2
2
2
BE[3:0]
EA[21:2]
BE
Address
3
4
ED[31:0]
1
5
2
5
Read Data
†
AOE/SDRAS/SSOE
†
†
ARE/SDCAS/SSADS
AWE/SDWE/SSWE
7
7
6
6
ARDY
†
AOE/SDRAS/SSOE, ARE/SDCAS/SSADS, and AWE/SDWE/SSWE operate as AOE (identified under select signals), ARE, and AWE,
respectively, during asynchronous memory accesses.
Figure 18. Asynchronous Memory Read Timing
50
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Hold = 2
Strobe = 3
Not Ready
ECLKOUT
CEx
8
8
8
8
9
9
9
9
BE[3:0]
BE
EA[21:2]
ED[31:0]
Address
Write Data
†
†
AOE/SDRAS/SSOE
ARE/SDCAS/SSADS
10
10
†
AWE/SDWE/SSWE
7
7
6
6
ARDY
†
AOE/SDRAS/SSOE, ARE/SDCAS/SSADS, and AWE/SDWE/SSWE operate as AOE (identified under select signals), ARE, and AWE,
respectively, during asynchronous memory accesses.
Figure 19. Asynchronous Memory Write Timing
51
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS-BURST MEMORY TIMING
†
timing requirements for synchronous-burst SRAM cycles (see Figure 20)
C6211−150
C6211−167
C6211B−150
C6211B−167
C6211BGFNA−150
NO.
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
Setup time, read EDx valid before
ECLKOUT high
6
7
t
t
2.5
2.5
2.5
ns
ns
su(EDV-EKOH)
Hold time, read EDx valid after
ECLKOUT high
1
2.5
2
h(EKOH-EDV)
†
The C6211/C6211B SBSRAM interface takes advantage of the internal burst counter in the SBSRAM. Accesses default to incrementing 4-word
bursts, but random bursts and decrementing bursts are done by interrupting bursts in progress. All burst types can sustain continuous data flow.
switching characteristics over recommended operating conditions for synchronous-burst SRAM
†‡
cycles (see Figure 20 and Figure 21)
C6211−150
C6211−167
C6211B−150
C6211B−167
C6211BGFNA−150
NO.
PARAMETER
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
Delay time, ECLKOUT high to CEx
valid
1
2
t
t
t
t
t
t
t
t
t
t
1.5
6.5
6.5
1
6.5
1.2
6.5
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
d(EKOH-CEV)
d(EKOH-BEV)
d(EKOH-BEIV)
d(EKOH-EAV)
d(EKOH-EAIV)
d(EKOH-ADSV)
d(EKOH-OEV)
d(EKOH-EDV)
d(EKOH-EDIV)
d(EKOH-WEV)
Delay time, ECLKOUT high to BEx
valid
6.5
6.5
6.5
6.5
Delay time, ECLKOUT high to BEx
invalid
3
1.5
1
1.2
Delay time, ECLKOUT high to EAx
valid
4
6.5
Delay time, ECLKOUT high to EAx
invalid
5
1.5
1.5
1.5
1
1
1
1.2
1.2
1.2
Delay time, ECLKOUT high to
ARE/SDCAS/SSADS valid
8
6.5
6.5
7
6.5
6.5
7
6.5
6.5
7
Delay time, ECLKOUT high to
AOE/SDRAS/SSOE valid
9
Delay time, ECLKOUT high to EDx
valid
10
11
12
Delay time, ECLKOUT high to EDx
invalid
1.5
1.5
1
1
1.2
1.2
Delay time, ECLKOUT high to
AWE/SDWE/SSWE valid
6.5
6.5
6.5
†
‡
The C6211/C6211B SBSRAM interface takes advantage of the internal burst counter in the SBSRAM. Accesses default to incrementing 4-word
bursts, but random bursts and decrementing bursts are done by interrupting bursts in progress. All burst types can sustain continuous data flow.
ARE/SDCAS/SSADS, AOE/SDRAS/SSOE, and AWE/SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM
accesses.
52
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
ECLKOUT
1
1
CEx
2
3
BE1
BE2
BE3
EA
BE4
7
BE[3:0]
4
5
EA[21:2]
ED[31:0]
6
Q1
Q2
Q3
Q4
8
8
†
ARE/SDCAS/SSADS
9
9
†
†
AOE/SDRAS/SSOE
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AOE/SDRAS/SSOE, and AWE/SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM
accesses.
Figure 20. SBSRAM Read Timing
ECLKOUT
1
2
1
3
CEx
BE[3:0]
BE1
BE2
Q2
BE3
5
BE4
Q4
4
EA[21:2]
ED[31:0]
EA
10
11
12
Q1
Q3
8
8
†
†
ARE/SDCAS/SSADS
AOE/SDRAS/SSOE
12
†
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AOE/SDRAS/SSOE, and AWE/SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM
accesses.
Figure 21. SBSRAM Write Timing
53
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS DRAM TIMING
†
timing requirements for synchronous DRAM cycles (see Figure 22)
C6211−150
C6211−167
C6211B−150
C6211B−167
C6211BGFNA−150
NO.
UNIT
MIN MAX
MIN
MAX
MIN MAX
Setup time, read EDx valid before
ECLKOUT high
6
7
t
t
2.5
1
2.5
2.5
ns
ns
su(EDV-EKOH)
Hold time, read EDx valid after
ECLKOUT high
2.5
2
h(EKOH-EDV)
†
The C6211/C6211B SDRAM interface takes advantage of the internal burst counter in the SDRAM. Accesses default to incrementing 4-word
bursts, but random bursts and decrementing bursts are done by interrupting bursts in progress. All burst types can sustain continuous data flow.
switching characteristics over recommended operating conditions for synchronous DRAM
†‡
cycles (see Figure 22−Figure 28)
C6211−150
C6211−167
C6211B−150
C6211B−167
C6211BGFNA−150
NO.
PARAMETER
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
Delay time, ECLKOUT high to CEx
valid
1
2
t
t
t
t
t
t
t
t
t
t
1.5
6.5
6.5
1
6.5
1.2
6.5
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
d(EKOH-CEV)
d(EKOH-BEV)
d(EKOH-BEIV)
d(EKOH-EAV)
d(EKOH-EAIV)
d(EKOH-CASV)
d(EKOH-EDV)
d(EKOH-EDIV)
d(EKOH-WEV)
d(EKOH-RAS)
Delay time, ECLKOUT high to BEx
valid
6.5
6.5
6.5
6.5
Delay time, ECLKOUT high to BEx
invalid
3
1.5
1
1.2
Delay time, ECLKOUT high to EAx
valid
4
6.5
Delay time, ECLKOUT high to EAx
invalid
5
1.5
1.5
1
1
1.2
1.2
Delay time, ECLKOUT high to
ARE/SDCAS/SSADS valid
8
6.5
7
6.5
7
6.5
7
Delay time, ECLKOUT high to EDx
valid
9
Delay time, ECLKOUT high to EDx
invalid
10
11
12
1.5
1.5
1.5
1
1
1
1.2
1.2
1.2
Delay time, ECLKOUT high to
AWE/SDWE/SSWE valid
6.5
6.5
6.5
6.5
6.5
6.5
Delay time, ECLKOUT high to
AOE/SDRAS/SSOE valid
†
‡
The C6211/C6211B SDRAM interface takes advantage of the internal burst counter in the SDRAM. Accesses default to incrementing 4-word
bursts, but random bursts and decrementing bursts are done by interrupting bursts in progress. All burst types can sustain continuous data flow.
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
54
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS DRAM TIMING (CONTINUED)
READ
ECLKOUT
CEx
1
1
2
3
BE[3:0]
BE1
BE2
BE3
BE4
4
5
5
5
Bank
EA[21:13]
EA[11:2]
4
Column
4
EA12
6
7
D2
ED[31:0]
D1
D3
D4
†
AOE/SDRAS/SSOE
8
8
†
†
ARE/SDCAS/SSADS
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 22. SDRAM Read Command (CAS Latency 3)
55
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS DRAM TIMING (CONTINUED)
WRITE
ECLKOUT
CEx
1
2
4
4
4
9
2
4
5
5
5
9
3
BE[3:0]
BE1
Bank
BE2
BE3
BE4
EA[21:13]
Column
EA[11:2]
EA12
10
ED[31:0]
D1
D2
D3
D4
†
AOE/SDRAS/SSOE
ARE/SDCAS/SSADS
8
8
†
11
11
†
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 23. SDRAM Write Command
56
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS DRAM TIMING (CONTINUED)
ACTV
ECLKOUT
1
1
CEx
BE[3:0]
4
5
5
5
Bank Activate
EA[21:13]
EA[11:2]
4
Row Address
4
Row Address
EA12
ED[31:0]
12
12
†
†
AOE/SDRAS/SSOE
ARE/SDCAS/SSADS
†
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 24. SDRAM ACTV Command
DCAB
ECLKOUT
1
1
CEx
BE[3:0]
EA[21:13, 11:2]
4
12
11
5
12
11
EA12
ED[31:0]
†
†
AOE/SDRAS/SSOE
ARE/SDCAS/SSADS
†
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 25. SDRAM DCAB Command
57
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS DRAM TIMING (CONTINUED)
DEAC
ECLKOUT
1
1
CEx
BE[3:0]
4
5
EA[21:13]
EA[11:2]
Bank
4
5
EA12
ED[31:0]
12
11
12
11
†
†
AOE/SDRAS/SSOE
ARE/SDCAS/SSADS
†
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 26. SDRAM DEAC Command
REFR
ECLKOUT
1
1
CEx
BE[3:0]
EA[21:2]
EA12
ED[31:0]
12
8
12
8
†
AOE/SDRAS/SSOE
†
†
ARE/SDCAS/SSADS
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 27. SDRAM REFR Command
58
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
SYNCHRONOUS DRAM TIMING (CONTINUED)
MRS
ECLKOUT
1
1
5
CEx
BE[3:0]
4
EA[21:2]
ED[31:0]
MRS value
12
8
12
8
†
AOE/SDRAS/SSOE
ARE/SDCAS/SSADS
†
11
11
†
AWE/SDWE/SSWE
†
ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 28. SDRAM MRS Command
59
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
HOLD/HOLDA TIMING
†
timing requirements for the HOLD/HOLDA cycles (see Figure 29)
−150
−167
NO.
UNIT
MIN MAX
3
t
Output hold time, HOLD low after HOLDA low
E
ns
oh(HOLDAL-HOLDL)
E = ECLKIN period in ns
†
†‡
switching characteristics over recommended operating conditions for the HOLD/HOLDA cycles
(see Figure 29)
−150
−167
NO.
PARAMETER
UNIT
MIN
2E
0
MAX
§
1
2
4
5
t
t
t
t
Delay time, HOLD low to EMIF Bus high impedance
Delay time, EMIF Bus high impedance to HOLDA low
Delay time, HOLD high to EMIF Bus low impedance
Delay time, EMIF Bus low impedance to HOLDA high
ns
ns
ns
ns
d(HOLDL-EMHZ)
d(EMHZ-HOLDAL)
d(HOLDH-EMLZ)
d(EMLZ-HOLDAH)
2E
7E
2E
2E
0
†
‡
§
E = ECLKIN period in ns
EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE/SDCAS/SSADS, AOE/SDRAS/SSOE, and AWE/SDWE/SSWE.
All pending EMIF transactions are allowed to complete before HOLDA is asserted. If no bus transactions are occurring, then the minimum delay
time can be achieved. Also, bus hold can be indefinitely delayed by setting NOHOLD = 1.
External Requestor
DSP Owns Bus
DSP Owns Bus
Owns Bus
3
HOLD
2
5
HOLDA
1
C6211/C6211B
4
†
EMIF Bus
C6211/C6211B
†
EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE/SDCAS/SSADS, AOE/SDRAS/SSOE, and AWE/SDWE/SSWE.
Figure 29. HOLD/HOLDA Timing
60
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
BUSREQ TIMING
switching characteristics over recommended operating conditions for the BUSREQ cycles
(see Figure 30)
−150
−167
NO.
PARAMETER
UNIT
MIN
MAX
1
t
Delay time, ECLKOUT high to BUSREQ valid
1.5
11
ns
d(EKOH-BUSRV)
ECLKOUT
BUSREQ
1
1
Figure 30. BUSREQ Timing
61
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
RESET TIMING
†
timing requirements for reset (see Figure 31)
−150
−167
NO.
UNIT
MIN
MAX
‡
Width of the RESET pulse (PLL stable)
10P
250
2P
ns
µs
ns
ns
1
t
w(RST)
§
Width of the RESET pulse (PLL needs to sync up)
¶
Setup time, HD boot configuration bits valid before RESET high
14
15
t
t
su(HD)
¶
Hold time, HD boot configuration bits valid after RESET high
2P
h(HD)
†
‡
§
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
This parameter applies to CLKMODE x1 when CLKIN is stable, and applies to CLKMODE x4 when CLKIN and PLL are stable.
This parameter applies to CLKMODE x4 only (it does not apply to CLKMODE x1). The RESET signal is not connected internally to the clock PLL
circuit. The PLL, however, may need up to 250 µs to stabilize following device power up or after PLL configuration has been changed. During
that time, RESET must be asserted to ensure proper device operation. See the clock PLL section for PLL lock times.
HD[4:3] are the boot configuration pins during device reset.
¶
†#||
switching characteristics over recommended operating conditions during reset
(see Figure 31)
−150
−167
NO.
PARAMETER
UNIT
MAX
MIN
2
3
t
t
t
t
t
t
t
t
t
t
t
t
Delay time, RESET low to ECLKIN synchronized internally
Delay time, RESET high to ECLKIN synchronized internally
Delay time, RESET low to EMIF Z group high impedance
Delay time, RESET high to EMIF Z group valid
Delay time, RESET low to EMIF high group invalid
Delay time, RESET high to EMIF high group valid
Delay time, RESET low to EMIF low group invalid
Delay time, RESET high to EMIF low group valid
Delay time, RESET low to high group invalid
2P + 3E
2P + 3E
2P + 3E
3P + 4E
3P + 4E
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
d(RSTL-ECKI)
d(RSTH-ECKI)
4
d(RSTL-EMIFZHZ)
d(RSTH-EMIFZV)
d(RSTL-EMIFHIV)
d(RSTH-EMIFHV)
d(RSTL-EMIFLIV)
d(RSTH-EMIFLV)
d(RSTL-HIGHIV)
d(RSTH-HIGHV)
d(RSTL-ZHZ)
5
3P + 4E
3P + 4E
3P + 4E
4P
6
2P + 3E
2P + 3E
2P
7
8
9
10
11
12
13
Delay time, RESET high to high group valid
Delay time, RESET low to Z group high impedance
Delay time, RESET high to Z group valid
2P
2P
d(RSTH-ZV)
†
#
||
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
E = ECLKIN period in ns
EMIF Z group consists of:
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE
EMIF high group consists of: HOLDA
EMIF low group consists of: BUSREQ
High group consists of:
Z group consists of:
HRDY and HINT
HD[15:0], CLKX0, CLKX1, FSX0, FSX1, DX0, DX1, CLKR0, CLKR1, FSR0, FSR1, TOUT0, and TOUT1.
62
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
RESET TIMING (CONTINUED)
CLKOUT1
CLKOUT2
1
15
14
RESET
2
4
6
8
3
§
ECLKIN
5
7
†
†
EMIF Z Group
EMIF High Group
9
†
EMIF Low Group
High Group
10
12
11
13
†
†
‡
Z Group
HD[8, 4:3]
§
†
ECLKIN should be provided during reset in order to drive EMIF signals to the correct reset values. ECLKOUT continues to clock as long as
ECLKIN is provided.
EMIF Z group consists of:
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE/SDCAS/SSADS, AWE/SDWE/SSWE, and AOE/SDRAS/SSOE
EMIF high group consists of: HOLDA
EMIF low group consists of: BUSREQ
High group consists of:
Z group consists of:
HD[8, 4:3] are the endianness and boot configuration pins during device reset.
HRDY and HINT
HD[15:0], CLKX0, CLKX1, FSX0, FSX1, DX0, DX1, CLKR0, CLKR1, FSR0, FSR1, TOUT0, and TOUT1.
‡
Figure 31. Reset Timing
63
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2005
EXTERNAL INTERRUPT TIMING
†
timing requirements for external interrupts (see Figure 32)
−150
−167
NO.
UNIT
MIN
MAX
1
2
t
t
Width of the interrupt pulse low
Width of the interrupt pulse high
2P
2P
ns
ns
w(ILOW)
w(IHIGH)
†
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
2
1
EXT_INT, NMI
Figure 32. External/NMI Interrupt Timing
64
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
HOST-PORT INTERFACE TIMING
†‡
timing requirements for host-port interface cycles [C6211] (see Figure 33, Figure 34, Figure 35,
and Figure 36)
C6211−150
C6211−167
NO.
UNIT
MIN
5
MAX
§
1
2
t
t
t
t
t
t
t
t
Setup time, select signals valid before HSTROBE low
ns
ns
ns
ns
ns
ns
ns
ns
su(SELV-HSTBL)
h(HSTBL-SELV)
w(HSTBL)
§
Hold time, select signals valid after HSTROBE low
4
3
Pulse duration, HSTROBE low
4P
4P
5
4
Pulse duration, HSTROBE high between consecutive accesses
w(HSTBH)
§
Setup time, select signals valid before HAS low
10
11
12
13
su(SELV-HASL)
h(HASL-SELV)
su(HDV-HSTBH)
h(HSTBH-HDV)
§
Hold time, select signals valid after HAS low
3
Setup time, host data valid before HSTROBE high
Hold time, host data valid after HSTROBE high
5
3
Hold time, HSTROBE low after HRDY low. HSTROBE should not be inactivated
until HRDY is active (low); otherwise, HPI writes will not complete properly.
14
t
2
ns
h(HRDYL-HSTBL)
18
19
t
t
Setup time, HAS low before HSTROBE low
Hold time, HAS low after HSTROBE low
2
2
ns
ns
su(HASL-HSTBL)
h(HSTBL-HASL)
†
‡
§
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
Select signals include: HCNTL[1:0], HR/W, and HHWIL.
switching characteristics over recommended operating conditions during host-port interface
†‡
cycles [C6211] (see Figure 33, Figure 34, Figure 35, and Figure 36)
C6211−150
C6211−167
NO.
PARAMETER
UNIT
MIN MAX
¶
5
6
t
t
t
t
t
t
t
t
t
Delay time, HCS to HRDY
1
15
15
ns
ns
ns
ns
ns
ns
ns
ns
ns
d(HCS-HRDY)
#
Delay time, HSTROBE low to HRDY high
3
d(HSTBL-HRDYH)
d(HSTBL-HDLZ)
d(HDV-HRDYL)
oh(HSTBH-HDV)
d(HSTBH-HDHZ)
d(HSTBL-HDV)
d(HSTBH-HRDYH)
d(HASL-HRDYH)
7
Delay time, HSTROBE low to HD low impedance for an HPI read
Delay time, HD valid to HRDY low
2
8
2P − 4
2P
15
15
15
15
15
9
Output hold time, HD valid after HSTROBE high
Delay time, HSTROBE high to HD high impedance
Delay time, HSTROBE low to HD valid
3
3
3
3
3
15
16
17
20
||
Delay time, HSTROBE high to HRDY high
Delay time, HAS low to HRDY high
†
‡
¶
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
HCS enables HRDY, and HRDY is always low when HCS is high. The case where HRDY goes high when HCS falls indicates that HPI is busy
completing a previous HPID write or READ with autoincrement.
#
||
This parameter is used during an HPID read. At the beginning of the first half-word transfer on the falling edge of HSTROBE, the HPI sends the
request to the EDMA internal address generation hardware, and HRDY remains high until the EDMA internal address generation hardware loads
the requested data into HPID.
This parameter is used after the second half-word of an HPID write or autoincrement read. HRDY remains low if the access is not an HPID write
or autoincrement read. Reading or writing to HPIC or HPIA does not affect the HRDY signal.
65
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
HOST-PORT INTERFACE TIMING (CONTINUED)
†‡
timing requirements for host-port interface cycles [C6211BGFNA/C6211B] (see Figure 33,
Figure 34, Figure 35, and Figure 36)
C6211B−150
C6211B−167
C6211BGFNA−150
NO.
UNIT
MIN
5
MAX
§
1
2
t
t
t
t
t
t
t
t
Setup time, select signals valid before HSTROBE low
ns
ns
ns
ns
ns
ns
ns
ns
su(SELV-HSTBL)
h(HSTBL-SELV)
w(HSTBL)
§
Hold time, select signals valid after HSTROBE low
4
3
Pulse duration, HSTROBE low
4P
4P
5
4
Pulse duration, HSTROBE high between consecutive accesses
w(HSTBH)
§
Setup time, select signals valid before HAS low
10
11
12
13
su(SELV-HASL)
h(HASL-SELV)
su(HDV-HSTBH)
h(HSTBH-HDV)
§
Hold time, select signals valid after HAS low
3
Setup time, host data valid before HSTROBE high
Hold time, host data valid after HSTROBE high
5
3
Hold time, HSTROBE low after HRDY low. HSTROBE should not be
inactivated until HRDY is active (low); otherwise, HPI writes will not
complete properly.
14
t
2
ns
h(HRDYL-HSTBL)
18
19
t
t
Setup time, HAS low before HSTROBE low
Hold time, HAS low after HSTROBE low
2
2
ns
ns
su(HASL-HSTBL)
h(HSTBL-HASL)
†
‡
§
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
Select signals include: HCNTL[1:0], HR/W, and HHWIL.
switching characteristics over recommended operating conditions during host-port interface
†‡
cycles [C6211BGFNA/C6211B] (see Figure 33, Figure 34, Figure 35, and Figure 36)
C6211B−150
C6211BGFNA−150
C6211B−167
NO.
PARAMETER
UNIT
MIN
1
MAX
13
MIN MAX
¶
5
6
t
t
Delay time, HCS to HRDY
1
3
12
12
ns
ns
d(HCS-HRDY)
#
Delay time, HSTROBE low to HRDY high
3
13
d(HSTBL-HRDYH)
Delay time, HSTROBE low to HD low impedance for
an HPI read
7
t
2
2
ns
d(HSTBL-HDLZ)
8
t
t
t
t
t
t
Delay time, HD valid to HRDY low
2P − 4
2P
13
13
13
13
13
2P − 4
2P
12
12
12
12
12
ns
ns
ns
ns
ns
ns
d(HDV-HRDYL)
oh(HSTBH-HDV)
d(HSTBH-HDHZ)
d(HSTBL-HDV)
d(HSTBH-HRDYH)
d(HASL-HRDYH)
9
Output hold time, HD valid after HSTROBE high
Delay time, HSTROBE high to HD high impedance
Delay time, HSTROBE low to HD valid
3
3
3
3
3
3
3
3
3
3
15
16
17
20
||
Delay time, HSTROBE high to HRDY high
Delay time, HAS low to HRDY high
†
‡
¶
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
HCS enables HRDY, and HRDY is always low when HCS is high. The case where HRDY goes high when HCS falls indicates that HPI is busy
completing a previous HPID write or READ with autoincrement.
#
||
This parameter is used during an HPID read. At the beginning of the first half-word transfer on the falling edge of HSTROBE, the HPI sends the
request to the EDMA internal address generation hardware, and HRDY remains high until the EDMA internal address generation hardware loads
the requested data into HPID.
This parameter is used after the second half-word of an HPID write or autoincrement read. HRDY remains low if the access is not an HPID write
or autoincrement read. Reading or writing to HPIC or HPIA does not affect the HRDY signal.
66
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
HOST-PORT INTERFACE TIMING (CONTINUED)
HAS
HCNTL[1:0]
HR/W
1
1
1
1
2
2
2
2
2
2
1
1
HHWIL
4
3
3
†
HSTROBE
HCS
15
9
15
9
7
16
HD[15:0] (output)
HRDY (case 1)
HRDY (case 2)
5
5
1st halfword
2nd halfword
5
8
8
17
17
6
†
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 33. HPI Read Timing (HAS Not Used, Tied High)
†
HAS
19
11
19
11
10
10
10
10
HCNTL[1:0]
HR/W
11
11
11
11
10
10
HHWIL
4
3
‡
HSTROBE
18
18
HCS
15
15
7
9
16
9
17
17
HD[15:0] (output)
HRDY (case 1)
HRDY (case 2)
1st half-word
2nd half-word
5
8
8
5
5
20
†
‡
For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 34. HPI Read Timing (HAS Used)
67
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
HOST-PORT INTERFACE TIMING (CONTINUED)
HAS
HCNTL[1:0]
HR/W
1
1
2
2
2
2
3
1
1
1
1
2
2
HHWIL
3
4
14
†
HSTROBE
HCS
HD[15:0] (input)
HRDY
12
12
13
2nd halfword
13
17
1st halfword
5
5
†
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 35. HPI Write Timing (HAS Not Used, Tied High)
†
HAS
19
11
19
11
11
11
10
10
10
10
10
10
HCNTL[1:0]
HR/W
11
11
HHWIL
3
4
14
‡
HSTROBE
18
12
18
HCS
HD[15:0] (input)
HRDY
12
13
13
1st half-word
2nd half-word
5
5
17
†
‡
For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 36. HPI Write Timing (HAS Used)
68
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING
†‡
timing requirements for McBSP (see Figure 37)
−150
−167
NO.
UNIT
MIN
MAX
§
2
3
t
t
Cycle time, CLKR/X
CLKR/X ext
CLKR/X ext
CLKR int
CLKR ext
CLKR int
CLKR ext
CLKR int
CLKR ext
CLKR int
CLKR ext
CLKX int
CLKX ext
CLKX int
CLKX ext
2P
ns
ns
c(CKRX)
Pulse duration, CLKR/X high or CLKR/X low
0.5t
c(CKRX)
− 1
20
1
w(CKRX)
5
6
t
t
t
t
t
t
Setup time, external FSR high before CLKR low
Hold time, external FSR high after CLKR low
Setup time, DR valid before CLKR low
ns
ns
ns
ns
ns
ns
su(FRH-CKRL)
h(CKRL-FRH)
su(DRV-CKRL)
h(CKRL-DRV)
su(FXH-CKXL)
h(CKXL-FXH)
6
3
22
3
7
3
8
Hold time, DR valid after CLKR low
4
23
1
10
11
Setup time, external FSX high before CLKX low
Hold time, external FSX high after CLKX low
6
3
†
‡
§
CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
The minimum CLKR/X period is twice the CPU cycle time (2P). This means that the maximum bit rate for communications between the McBSP
and other device is 83 Mbps for 167 MHz CPU clock or 75 Mbps for 150 MHz CPU clock; where the McBSP is either the master or the slave.
Care must be taken to ensure that the AC timings specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP
communications is 33 Mbps; therefore, the minimum CLKR/X clock cycle is either twice the CPU cycle time (2P), or 30 ns (33 MHz), whichever
value is larger. For example, when running parts at 167 MHz (P = 6 ns), use 30 ns as the minimum CLKR/X clock cycle (by setting the appropriate
CLKGDV ratio or external clock source). When running parts at 60 MHz (P = 16.67 ns), use 2P = 33 ns (30 MHz) as the minimum CLKR/X clock
cycle. The maximum bit rate for McBSP-to-McBSP communications applies when the serial port is a master of the clock and frame syncs (with
CLKR connected to CLKX, FSR connected to FSX, CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY =
01b or 10b) and the other device the McBSP communicates to is a slave.
69
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
†‡
switching characteristics over recommended operating conditions for McBSP (see Figure 37)
−150
−167
NO.
PARAMETER
UNIT
MIN
MAX
Delay time, CLKS high to CLKR/X high for internal CLKR/X generated from
CLKS input
1
t
4
26
ns
d(CKSH-CKRXH)
§¶
2
3
4
t
t
t
Cycle time, CLKR/X
CLKR/X int
CLKR/X int
CLKR int
CLKX int
CLKX ext
CLKX int
CLKX ext
CLKX int
CLKX ext
2P
ns
ns
ns
c(CKRX)
#
#
Pulse duration, CLKR/X high or CLKR/X low
Delay time, CLKR high to internal FSR valid
C − 1
C + 1
w(CKRX)
−11
−11
3
3
3
9
4
9
d(CKRH-FRV)
9
t
t
t
Delay time, CLKX high to internal FSX valid
ns
ns
ns
d(CKXH-FXV)
dis(CKXH-DXHZ)
d(CKXH-DXV)
−9
3
Disable time, DX high impedance following last data bit
from CLKX high
12
13
||
||
−9+ D1
3 + D1
4 + D2
Delay time, CLKX high to DX valid
Delay time, FSX high to DX valid
||
||
19 + D2
FSX int
FSX ext
−1
3
3
9
14
t
ns
d(FXH-DXV)
ONLY applies when in data
delay 0 (XDATDLY = 00b) mode
†
‡
§
¶
CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
Minimum delay times also represent minimum output hold times.
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
The minimum CLKR/X period is twice the CPU cycle time (2P). This means that the maximum bit rate for communications between the McBSP
and other device is 83 Mbps for 167 MHz CPU clock or 75 Mbps for 150 MHz CPU clock; where the McBSP is either the master or the slave.
Care must be taken to ensure that the AC timings specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP
communications is 33 Mbps; therefore, the minimum CLKR/X clock cycle is either twice the CPU cycle time (2P), or 30 ns (33 MHz), whichever
value is larger. For example, when running parts at 167 MHz (P = 6 ns), use 30 ns as the minimum CLKR/X clock cycle (by setting the appropriate
CLKGDV ratio or external clock source). When running parts at 60 MHz (P = 16.67 ns), use 2P = 33 ns (30 MHz) as the minimum CLKR/X clock
cycle. The maximum bit rate for McBSP-to-McBSP communications applies when the serial port is a master of the clock and frame syncs (with
CLKR connected to CLKX, FSR connected to FSX, CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY =
01b or 10b) and the other device the McBSP communicates to is a slave.
#
C = H or L
S = sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)
=
sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see ¶ footnote above).
Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR.
If DXENA = 0, then D1 = D2 = 0
||
If DXENA = 1, then D1 = 2P, D2 = 4P
70
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKS
1
2
3
3
CLKR
4
4
FSR (int)
5
6
FSR (ext)
7
8
DR
Bit(n-1)
(n-2)
(n-3)
2
3
3
CLKX
9
FSX (int)
11
10
FSX (ext)
FSX (XDATDLY=00b)
13
(n-2)
14
13
12
DX
Bit 0
Bit(n-1)
(n-3)
Figure 37. McBSP Timings
71
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for FSR when GSYNC = 1 (see Figure 38)
−150
−167
NO.
UNIT
MIN
MAX
1
2
t
t
Setup time, FSR high before CLKS high
Hold time, FSR high after CLKS high
4
4
ns
ns
su(FRH-CKSH)
h(CKSH-FRH)
CLKS
1
2
FSR external
CLKR/X (no need to resync)
CLKR/X (needs resync)
Figure 38. FSR Timing When GSYNC = 1
72
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
†‡
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 0 (see Figure 39)
−150
−167
NO.
UNIT
MASTER
SLAVE
MIN MAX
MIN
26
4
MAX
4
5
t
t
Setup time, DR valid before CLKX low
Hold time, DR valid after CLKX low
2 − 6P
ns
ns
su(DRV-CKXL)
6 + 12P
h(CKXL-DRV)
†
‡
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
†‡
slave: CLKSTP = 10b, CLKXP = 0 (see Figure 39)
−150
−167
NO.
PARAMETER
UNIT
§
MASTER
SLAVE
MIN
MIN MAX
MAX
¶
1
2
3
t
t
t
Hold time, FSX low after CLKX low
T − 9 T + 9
L − 9 L + 9
ns
ns
ns
h(CKXL-FXL)
d(FXL-CKXH)
d(CKXH-DXV)
#
Delay time, FSX low to CLKX high
Delay time, CLKX high to DX valid
−9
9
6P + 4 10P + 20
Disable time, DX high impedance following last data bit from
CLKX low
6
t
L − 9 L + 9
ns
dis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
7
8
t
t
2P + 3
4P + 2
6P + 20
8P + 20
ns
ns
dis(FXH-DXHZ)
Delay time, FSX low to DX valid
d(FXL-DXV)
†
‡
§
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = Sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)
=
Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
¶
#
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
73
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
FSX
1
2
8
7
6
3
DX
DR
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
(n-3)
(n-4)
4
5
Bit 0
(n-2)
(n-3)
(n-4)
Figure 39. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
74
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
†‡
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 0 (see Figure 40)
−150
−167
NO.
UNIT
MASTER
SLAVE
MIN MAX
MIN
26
4
MAX
4
5
t
t
Setup time, DR valid before CLKX high
Hold time, DR valid after CLKX high
2 − 6P
ns
ns
su(DRV-CKXH)
6 + 12P
h(CKXH-DRV)
†
‡
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
†‡
slave: CLKSTP = 11b, CLKXP = 0 (see Figure 40)
−150
−167
NO.
PARAMETER
UNIT
§
MASTER
SLAVE
MIN
MIN MAX
MAX
¶
1
2
3
t
t
t
Hold time, FSX low after CLKX low
L − 9 L + 9
T − 9 T + 9
ns
ns
ns
h(CKXL-FXL)
d(FXL-CKXH)
d(CKXL-DXV)
#
Delay time, FSX low to CLKX high
Delay time, CLKX low to DX valid
−9
9
6P + 4 10P + 20
6P + 3 10P + 20
Disable time, DX high impedance following last data bit from
CLKX low
6
t
−9
9
ns
ns
dis(CKXL-DXHZ)
7
t
Delay time, FSX low to DX valid
H − 9 H + 9
4P + 2
8P + 20
d(FXL-DXV)
†
‡
§
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = Sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)
=
Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
¶
#
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
CLKX
1
2
7
FSX
DX
6
3
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
(n-3)
(n-3)
(n-4)
4
5
DR
Bit 0
(n-2)
(n-4)
Figure 40. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
75
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
†‡
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1 (see Figure 41)
−150
−167
NO.
UNIT
MASTER
SLAVE
MIN MAX
MIN
26
4
MAX
4
5
t
t
Setup time, DR valid before CLKX high
Hold time, DR valid after CLKX high
2 − 6P
ns
ns
su(DRV-CKXH)
6 + 12P
h(CKXH-DRV)
†
‡
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
†‡
slave: CLKSTP = 10b, CLKXP = 1 (see Figure 41)
−150
−167
NO.
PARAMETER
UNIT
§
MASTER
SLAVE
MIN
MIN MAX
MAX
¶
1
2
3
t
t
t
Hold time, FSX low after CLKX high
T − 9 T + 9
H − 9 H + 9
ns
ns
ns
h(CKXH-FXL)
d(FXL-CKXL)
d(CKXL-DXV)
#
Delay time, FSX low to CLKX low
Delay time, CLKX low to DX valid
−9
9
6P + 4 10P + 20
Disable time, DX high impedance following last data bit from
CLKX high
6
t
H − 9 H + 9
ns
dis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
7
8
t
t
2P + 3
4P + 2
6P + 20
8P + 20
ns
ns
dis(FXH-DXHZ)
Delay time, FSX low to DX valid
d(FXL-DXV)
†
‡
§
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = Sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)
=
Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
¶
#
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
76
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
FSX
1
2
7
6
8
3
DX
DR
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
(n-3)
(n-4)
4
5
Bit 0
(n-2)
(n-3)
(n-4)
Figure 41. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
77
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
†‡
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 1 (see Figure 42)
−150
−167
NO.
UNIT
MASTER
SLAVE
MIN MAX
MIN
26
4
MAX
4
5
t
t
Setup time, DR valid before CLKX high
Hold time, DR valid after CLKX high
2 − 6P
ns
ns
su(DRV-CKXH)
6 + 12P
h(CKXH-DRV)
†
‡
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
†‡
slave: CLKSTP = 11b, CLKXP = 1 (see Figure 42)
−150
−167
NO.
PARAMETER
UNIT
§
MASTER
SLAVE
MIN
MIN MAX
MAX
¶
1
2
3
t
t
t
Hold time, FSX low after CLKX high
H − 9 H + 9
T − 9 T + 9
ns
ns
ns
h(CKXH-FXL)
d(FXL-CKXL)
d(CKXH-DXV)
#
Delay time, FSX low to CLKX low
Delay time, CLKX high to DX valid
−9
9
6P + 4 10P + 20
6P + 3 10P + 20
Disable time, DX high impedance following last data bit from
CLKX high
6
t
−9
9
ns
ns
dis(CKXH-DXHZ)
7
t
Delay time, FSX low to DX valid
L − 9 L + 9
4P + 2
8P + 20
d(FXL-DXV)
†
‡
§
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = Sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)
=
Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
¶
#
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
78
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
FSX
DX
1
2
7
6
3
Bit 0
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
(n-3)
(n-4)
4
5
DR
(n-2)
(n-3)
(n-4)
Figure 42. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
79
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢕ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢐ
ꢑ
ꢒ
ꢌ
ꢓ
ꢀ
ꢏ
ꢌ
ꢔꢌ
ꢀꢕ
ꢖ
ꢂ
ꢌ
ꢔ
ꢓ
ꢖ
ꢑ
ꢗ
ꢒ
ꢆ
ꢎ
ꢂ
ꢂ
ꢒ
ꢗ
ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
TIMER TIMING
†
timing requirements for timer inputs (see Figure 43)
−150
−167
NO.
UNIT
MIN
MAX
1
2
t
t
Pulse duration, TINP high
Pulse duration, TINP low
2P
2P
ns
ns
w(TINPH)
w(TINPL)
†
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
†
switching characteristics over recommended operating conditions for timer outputs
(see Figure 43)
−150
−167
NO.
PARAMETER
UNIT
MIN
MAX
3
4
t
t
Pulse duration, TOUT high
Pulse duration, TOUT low
4P−3
4P−3
ns
ns
w(TOUTH)
w(TOUTL)
†
P = 1/CPU clock frequency in ns. For example, when running parts at 167 MHz, use P = 6 ns.
2
1
TINPx
4
3
TOUTx
Figure 43. Timer Timing
80
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
JTAG TEST-PORT TIMING
timing requirements for JTAG test port (see Figure 44)
−150
−167
NO.
UNIT
MIN
35
10
9
MAX
1
3
4
t
t
t
Cycle time, TCK
ns
ns
ns
c(TCK)
Setup time, TDI/TMS/TRST valid before TCK high
Hold time, TDI/TMS/TRST valid after TCK high
su(TDIV-TCKH)
h(TCKH-TDIV)
switching characteristics over recommended operating conditions for JTAG test port
(see Figure 44)
−150
−167
NO.
PARAMETER
UNIT
MIN
MAX
2
t
Delay time, TCK low to TDO valid
–3
18
ns
d(TCKL-TDOV)
1
TCK
TDO
2
2
4
3
TDI/TMS/TRST
Figure 44. JTAG Test-Port Timing
81
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂ ꢃ ꢄꢅ ꢆ ꢇ ꢄꢈꢈ ꢉ ꢀꢁ ꢂꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢊ
ꢋ ꢌ ꢍꢎꢏ ꢐꢑ ꢒꢌ ꢓ ꢀ ꢏ ꢌ ꢔꢌ ꢀꢕꢖ ꢂ ꢌ ꢔꢓ ꢕꢖ ꢑ ꢗꢒ ꢆꢎꢂ ꢂꢒ ꢗꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
MECHANICAL DATA
The following tables show the thermal resistance characteristics for the GFN and ZFN mechanical packages.
thermal resistance characteristics (S-PBGA package) for GFN
†
NO
1
°C/W
6.4
Air Flow (m/s)
RΘ
RΘ
RΘ
RΘ
RΘ
Junction-to-case
N/A
0.0
0.5
1.0
2.0
JC
JA
JA
JA
JA
2
Junction-to-free air
Junction-to-free air
Junction-to-free air
Junction-to-free air
25.5
23.1
22.3
21.2
3
4
5
†
m/s = meters per second
thermal resistance characteristics (S-PBGA package) for ZFN
†
NO
°C/W
6.4
Air Flow (m/s)
1
2
3
4
5
RΘ
RΘ
RΘ
RΘ
RΘ
Junction-to-case
N/A
0.0
0.5
1.0
2.0
JC
JA
JA
JA
JA
Junction-to-free air
Junction-to-free air
Junction-to-free air
Junction-to-free air
25.5
23.1
22.3
21.2
†
m/s = meters per second
82
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆꢇ ꢄ ꢈꢈ ꢉ ꢀ ꢁꢂ ꢃ ꢄꢅ ꢆꢇ ꢄꢈꢈꢊ
ꢋ ꢌꢍ ꢎꢏꢐꢑꢒ ꢌ ꢓꢀ ꢏꢌ ꢔꢌ ꢀꢕꢖ ꢂꢌ ꢔ ꢓꢕꢖ ꢑꢗ ꢒ ꢆꢎ ꢂ ꢂꢒ ꢗ ꢂ
SPRS073L − AUGUST 1998 − REVISED JUNE 2004
packaging information
The following packaging information and addendum reflect the most current released data available for the
designated device(s). This data is subject to change without notice and without revision of this document.
83
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
PACKAGE OPTION ADDENDUM
www.ti.com
21-Nov-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
BGA
BGA
BGA
Drawing
TMS320C6211BGFN150
TMS320C6211BGFN167
TMS320C6211BZFN150
ACTIVE
ACTIVE
ACTIVE
GFN
256
256
256
40
40
40
TBD
TBD
SNPB
SNPB
Level-4-220C-72HR
Level-4-220C-72HR
Level-4-260C-72HR
GFN
ZFN
Pb-Free
(RoHS)
SNAGCU
TMS320C6211BZFN167
TMS320C6211GFN150
TMS320C6211GFN167
TMS32C6211BGFNA150
TMX320C6211GFN
ACTIVE
OBSOLETE
OBSOLETE
ACTIVE
BGA
BGA
BGA
BGA
BGA
BGA
ZFN
GFN
GFN
GFN
GFN
GFN
256
256
256
256
256
256
40
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
SNPB
Call TI
Call TI
Call TI
Call TI
Call TI
40
Level-4-220C-72HR
Call TI
OBSOLETE
OBSOLETE
TMX320C6211GFN21
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MBGA002C – JANUARY 1995 – REVISED MARCH 2002
GFN (S-PBGA-N256)
PLASTIC BALL GRID ARRAY
27,20
26,80
24,70
23,80
SQ
SQ
24,13 TYP
1,27
0,635
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
A1 Corner
1
3
5
7
9
11 13 15 17 19
10 12 14 16 18 20
2
4
6
8
Bottom View
2,32 MAX
1,17 NOM
Seating Plane
0,15
0,90
0,60
0,40
0,30
M
0,15
0,70
0,50
4040185-2/D 02/02
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MO-151
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明