TMS320F28067-Q1 [TI]
TMS320F2806x Microcontrollers;型号: | TMS320F28067-Q1 |
厂家: | TEXAS INSTRUMENTS |
描述: | TMS320F2806x Microcontrollers 微控制器 |
文件: | 总185页 (文件大小:5091K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062,TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
TMS320F2806x Microcontrollers
– 16 PWM channels total (8 HRPWM-capable)
– Independent 16-bit timer in each module
Three input Enhanced Capture (eCAP) modules
Up to 4 High-Resolution Capture (HRCAP)
modules
Up to 2 Enhanced Quadrature Encoder Pulse
(eQEP) modules
12-bit Analog-to-Digital Converter (ADC), dual
Sample-and-Hold (S/H)
1 Features
•
High-efficiency 32-bit CPU (TMS320C28x)
•
•
– 90 MHz (11.11-ns cycle time)
– 16 × 16 and 32 × 32 Multiply and Accumulate
(MAC) operations
– 16 × 16 dual MAC
– Harvard bus architecture
•
•
– Atomic operations
– Fast interrupt response and processing
– Unified memory programming model
– Code-efficient (in C/C++ and Assembly)
Floating-Point Unit (FPU)
– Native single-precision floating-point operations
Programmable Control Law Accelerator (CLA)
– 32-bit floating-point math accelerator
– Executes code independently of the main CPU
Viterbi, Complex Math, CRC Unit (VCU)
– Extends C28x instruction set to support
complex multiply, Viterbi operations, and Cyclic
Redundency Check (CRC)
– Up to 3.46 MSPS
– Up to 16 channels
On-chip temperature sensor
128-bit security key and lock
– Protects secure memory blocks
– Prevents reverse-engineering of firmware
Serial port peripherals
– Two Serial Communications Interface (SCI)
[UART] modules
– Two Serial Peripheral Interface (SPI) modules
– One Inter-Integrated-Circuit (I2C) bus
– One Multichannel Buffered Serial Port (McBSP)
bus
•
•
•
•
•
•
•
Embedded memory
– Up to 256KB of flash
– Up to 100KB of RAM
– One Enhanced Controller Area Network
(eCAN)
– 2KB of One-Time Programmable (OTP) ROM
6-channel Direct Memory Access (DMA)
Low device and system cost
– Universal Serial Bus (USB) 2.0
(see Device Comparison for availability)
•
•
•
•
Full-speed device mode
Full-speed or low-speed host mode
– Single 3.3-V supply
•
•
Up to 54 individually programmable, multiplexed
General-Purpose Input/Output (GPIO) pins with
input filtering
Advanced emulation features
– Analysis and breakpoint functions
– Real-time debug through hardware
Package options
– 80-pin PFP and 100-pin PZP PowerPAD™
Thermally Enhanced Thin Quad Flatpacks
(HTQFPs)
– 80-pin PN and 100-pin PZ Low-Profile Quad
Flatpacks (LQFPs)
Temperature options
– T: –40°C to 105°C
– S: –40°C to 125°C
– Q: –40°C to 125°C (AEC Q100 qualification for
automotive applications)
– No power sequencing requirement
– Integrated power-on reset and brownout reset
– Low-power operating modes
– No analog support pin
Endianness: Little endian
JTAG boundary scan support
– IEEE Standard 1149.1-1990 Standard Test
Access Port and Boundary Scan Architecture
Clocking
– Two internal zero-pin oscillators
– On-chip crystal oscillator/external clock input
– Watchdog timer module
– Missing clock detection circuitry
Peripheral Interrupt Expansion (PIE) block that
supports all peripheral interrupts
Three 32-bit CPU timers
•
•
•
•
•
•
•
•
•
Advanced control peripherals
Up to 8 Enhanced Pulse-Width Modulator (ePWM)
modules
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
•
•
•
•
•
•
•
•
•
•
•
•
Micro inverter
Solar power optimizer
String inverter
2 Applications
•
•
•
•
•
•
•
•
•
•
•
•
Air conditioner outdoor unit
Door operator drive control
Inverter & motor control
On-board (OBC) & wireless charger
Automated sorting equipment
CNC control
Textile machine
Welding machine
EV charging station power module
Wireless vehicle charging module
Energy storage power conversion system (PCS)
Central inverter
AC drive control module
AC drive power stage module
Linear motor power stage
Servo drive control module
Servo drive power stage module
AC-input BLDC motor drive
DC-input BLDC motor drive
Industrial AC-DC
Three phase UPS
3 Description
C2000™ 32-bit microcontrollers are optimized for processing, sensing, and actuation to improve closed-loop
performance in real-time control applications such as industrial motor drives; solar inverters and digital power;
electrical vehicles and transportation; motor control; and sensing and signal processing. The C2000 line includes
the Premium performance MCUs and the Entry performance MCUs.
The F2806x family of microcontrollers (MCUs) provides the power of the C28x core and CLA coupled with highly
integrated control peripherals in low pin-count devices. This family is code-compatible with previous C28x-based
code, and also provides a high level of analog integration.
An internal voltage regulator allows for single-rail operation. Enhancements have been made to the HRPWM
module to allow for dual-edge control (frequency modulation). Analog comparators with internal 10-bit references
have been added and can be routed directly to control the ePWM outputs. The ADC converts from 0 to 3.3-V
fixed full-scale range and supports ratio-metric VREFHI/VREFLO references. The ADC interface has been
optimized for low overhead and latency.
To learn more about the C2000 MCUs, visit the C2000 Overview at www.ti.com/c2000.
Device Information
PART NUMBER(1)
TMS320F28069PZP
PACKAGE
HTQFP (100)
HTQFP (80)
LQFP (100)
LQFP (80)
BODY SIZE
14.0 mm × 14.0 mm
12.0 mm × 12.0 mm
14.0 mm × 14.0 mm
12.0 mm × 12.0 mm
TMS320F28069PFP
TMS320F28069PZ
TMS320F28069PN
(1) For more information on these devices, see Mechanical, Packaging, and Orderable Information.
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
3.1 Functional Block Diagram
Figure 3-1 shows a functional block diagram of the device.
M0 SARAM (1K´16)
(0-wait, Nonsecure)
L0 DPSARAM (2K´16)
(0-wait, Secure)
CLA Data RAM2
OTP 1K´16
Secure
M1 SARAM (1K´16)
(0-wait, Nonsecure)
L1 DPSARAM (1K´16)
(0-wait, Secure)
CLA Data RAM0
FLASH
128K´16
64K´16
L5 DPSARAM (8K´16)
(0-wait, Nonsecure)
DMA RAM0
Code
Security
Module
(CSM)
L2 DPSARAM (1K´16)
(0-wait, Secure)
CLA Data RAM1
8 equal sectors
Secure
L6 DPSARAM (8K´16)
(0-wait, Nonsecure)
DMA RAM1
L3 DPSARAM (4K´16)
(0-wait, Secure)
CLA Program RAM
PUMP
L7 DPSARAM (8K´16)
(0-wait, Nonsecure)
DMA RAM2
OTP/Flash
Wrapper
L4 SARAM (8K´16)
(0-wait, Secure)
PSWD
L8 DPSARAM (8K´16)
(0-wait, Nonsecure)
DMA RAM3
Memory Bus
DMA Bus
Boot-ROM
(32K´16)
(0-wait,
COMP1OUT
Nonsecure)
TRST
COMP2OUT
COMP3OUT
C28x 32-bit CPU
FPU
VCU
TCK, TDI, TMS
TDO
COMP
+
DAC
COMP1A
COMP1B
COMP2A
COMP2B
XCLKIN
CLA +
Message
RAMs
OSC1, OSC2,
Ext, PLLs,
LPM, WD,
LPM Wakeup
3 Ext. Interrupts
CPU Timer 0,
CPU Timer 1,
CPU Timer 2,
PIE
COMP3A
COMP3B
X1
X2
DMA
6-ch
XRS
ADC
0-wait
Result
Regs
CLA Bus
DMA Bus
A7:0
B7:0
Memory Bus
ADC
32-Bit Peripheral
Bus
32-Bit
Peripheral Bus
(CLA accessible)
32-Bit Peripheral Bus
(CLA accessible)
32-Bit Peripheral
Bus
32-Bit Peripheral
Bus
16-Bit Peripheral Bus
HRCAP1
HRCAP2
HRCAP3
HRCAP4
ePWM1 to ePWM8
HRPWM (8ch)
SCI-A SPI-A
SCI-B SPI-B
(4L FIFO) (4L FIFO)
eCAP1
eCAP2
eCAP3
I2C-A
(4L FIFO)
eCAN-A
(32-mbox)
eQEP1
eQEP2
USB-0
McBSP-A
GPIO Mux
Copyright © 2017, Texas Instruments Incorporated
A. Not all peripheral pins are available at the same time due to multiplexing.
Figure 3-1. Functional Block Diagram
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
3.2 System Device Diagram
C28x
Core
(90-MHz)
PWM-1A
PWM-1B
PWM1
(DMA-accessible)
ADC
(DMA-
accessible)
VREFLO
VREFHI
PWM-2A
PWM-2B
PWM2
(DMA-accessible)
FPU
VCU
VREF
PWM-3A
PWM-3B
PWM3
(DMA-accessible)
Flash Memory
RAM
A0
A1
A2
A3
A4
A5
A6
A7
B0
B1
B2
B3
B4
B5
B6
B7
PWM-4A
PWM-4B
PWM4
(DMA-accessible)
RAM
(Dual-Access)
12-Bit
3.46-MSPS
Dual
Sample-
and-
Hold
PWM-5A
PWM-5B
PWM5
(DMA-accessible)
PWM-6A
PWM-6B
PWM6
(DMA-accessible)
CLA Core
90-MHz Floating-Point
(Accelerator)
PWM-7A
PWM-7B
PWM7
(DMA-accessible)
SOC-based
(DMA-accessible)
PWM-8A
PWM-8B
PWM8
(DMA-accessible)
Temp
Sensor
6
TZ1
TZ2
TZ3
Trip Zone
CMP1-Out
CMP2-Out
CMP1-out
CMP2-out
CMP3-out
10-Bit
DAC
3
8
4
eCAP
eCAP ´ 3
eQEP ´ 2
10-Bit
DAC
CMP3-Out
eQEP
10-Bit
DAC
Analog
Comparators
HRCAP
HRCAP ´ 4
COMMS
Timers 32-bit
Vreg
Timer-0
Timer-1
Timer-2
4
8
2
2
6
2
UART ´ 2
SPI ´ 2
Int-Osc-1
Int-Osc-2
WD
PLL
X1
X2
On-chip Osc
POR/BOR
System
GPIO
Control
I2C
CAN
McBSP
(DMA-accessible)
USB
(DMA-accessible)
Figure 3-2. Peripheral Blocks
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................2
3 Description.......................................................................2
3.1 Functional Block Diagram...........................................3
3.2 System Device Diagram............................................. 4
4 Revision History.............................................................. 6
5 Device Comparison.........................................................7
5.1 Related Products........................................................ 8
6 Terminal Configuration and Functions..........................9
6.1 Pin Diagrams.............................................................. 9
6.2 Signal Descriptions................................................... 12
7 Specifications................................................................ 21
7.1 Absolute Maximum Ratings...................................... 21
7.2 ESD Ratings – Commercial...................................... 22
7.3 ESD Ratings – Automotive....................................... 22
7.4 Recommended Operating Conditions.......................23
7.5 Power Consumption Summary................................. 24
7.6 Electrical Characteristics...........................................28
7.7 Thermal Resistance Characteristics......................... 29
7.8 Thermal Design Considerations................................32
7.9 Debug Probe Connection Without Signal
7.14 Flash Timing............................................................40
8 Detailed Description......................................................43
8.1 Overview...................................................................43
8.2 Memory Maps........................................................... 53
8.3 Register Maps...........................................................65
8.4 Device Emulation Registers......................................67
8.5 VREG, BOR, POR.................................................... 69
8.6 System Control......................................................... 71
8.7 Low-power Modes Block...........................................80
8.8 Interrupts...................................................................81
8.9 Peripherals................................................................86
9 Applications, Implementation, and Layout............... 163
9.1 TI Reference Design...............................................163
10 Device and Documentation Support........................164
10.1 Device and Development Support Tool
Nomenclature............................................................164
10.2 Tools and Software............................................... 165
10.3 Documentation Support........................................ 167
10.4 Support Resources............................................... 168
10.5 Trademarks...........................................................168
10.6 Electrostatic Discharge Caution............................168
10.7 Glossary................................................................168
11 Mechanical, Packaging, and Orderable
Buffering for the MCU..................................................32
7.10 Parameter Information............................................ 33
7.11 Test Load Circuit..................................................... 33
7.12 Power Sequencing..................................................34
7.13 Clock Specifications................................................37
Information.................................................................. 169
11.1 Packaging Information.......................................... 169
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
4 Revision History
Changes from March 19, 2020 to February 1, 2021 (from Revision H (March 2020) to Revision I
(February 2021))
Page
•
•
•
Added Q1 Part Numbers................................................................................................................................ 0
Table 5-1: Added Q1 Part Numbers....................................................................................................................7
Figure 10-1: Added GPN information............................................................................................................. 164
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
5 Device Comparison
Table 5-1 lists the features of the TMS320F2806x devices.
Table 5-1. Device Comparison
28069
28069-Q1
28062
28069U(2) (5)
28069M (2) (3)
28069M-Q1
28069F (2) (3)
28069F-Q1
(90 MHz)
28068U(2) (5)
28068M (2) (3)
28068F (2) (3)
(90 MHz)
28067
28067-Q1
28067U(2) (5)
(90 MHz)
28066
28066-Q1
28066U(2) (5)
(90 MHz)
28065
28065-Q1
28065U(2) (5)
(90 MHz)
28062-Q1
28062U(2) (5)
28062F (2) (3)
28062F-Q1
(90 MHz)
28064
28063
TYPE
FEATURE
28064U(2) (5)
(90 MHz)
28063U(2) (5)
(90 MHz)
(1)
Package Type
(PFP and PZP are
PowerPAD HTQFPs.
PN and PZ are LQFPs.)
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
PN
PN
PN
PN
PN
PN
PN
PN
PZ
PZ
PZ
PZ
PZ
PZ
PZ
PZ
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
Instruction cycle
Floating-Point Unit (FPU)
VCU
–
11.11 ns
Yes
11.11 ns
Yes
11.11 ns
Yes
11.11 ns
Yes
11.11 ns
Yes
11.11 ns
Yes
11.11 ns
Yes
11.11 ns
Yes
Yes
Yes
No
No
Yes
Yes
No
No
CLA
0
0
–
–
Yes
No
No
No
Yes
No
No
No
6-Channel DMA
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
On-chip Flash (16-bit word)
On-chip SARAM (16-bit word)
128K
50K
128K
50K
128K
50K
128K
34K
64K
64K
50K
64K
34K
64K
26K
50K
Code security for on-chip
Flash, SARAM, and OTP
blocks
–
–
–
Yes
Yes
1K
Yes
Yes
1K
Yes
Yes
1K
Yes
Yes
1K
Yes
Yes
1K
Yes
Yes
1K
Yes
Yes
1K
Yes
Yes
1K
Boot ROM (32K × 16)
One-time programmable
(OTP) ROM
(16-bit word)
ePWM channels
1
1
16
14
16
14
16
14
16
14
16
14
16
14
16
14
16
14
High-resolution ePWM
Channels
8
3
8
3
8
3
8
3
8
3
8
3
8
3
8
3
eCAP inputs
HRCAP
0
0
0
–
4
2
1
1
4
2
1
1
4
2
1
1
4
2
1
1
4
2
1
1
4
2
1
1
4
2
1
1
4
2
1
1
eQEP modules
Watchdog timer
MSPS
Yes
3.46
Yes
3.46
Yes
3.46
Yes
3.46
Yes
3.46
Yes
3.46
Yes
3.46
Yes
3.46
Conversion Time
289 ns
289 ns
289 ns
289 ns
289 ns
289 ns
289 ns
289 ns
Channels
12-Bit
16
12
16
12
16
12
16
12
16
12
16
12
16
12
16
12
3
ADC
Temperature
Sensor
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Dual Sample-
and-Hold
Yes
3
Yes
3
Yes
3
Yes
3
Yes
3
Yes
3
Yes
3
Yes
3
32-Bit CPU timers
–
0
Comparators with Integrated
DACs
3
3
3
3
3
3
3
3
I2C
0
1
0
1
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
McBSP
eCAN
1
1
1
1
1
1
1
1
SPI
2
2
2
2
2
2
2
2
SCI
2
2
2
2
2
2
2
2
USB
1(2)
1
1(2)
1
1(2)
1
1(2)
1
1(2)
1
1(2)
1
1(2)
1
1(2)
1
2-pin Oscillator
0-pin Oscillator
2
2
2
2
2
2
2
2
GPIO
–
–
–
–
54
40
54
40
54
40
54
40
54
40
54
40
54
40
54
40
I/O pins
(shared)
AIO
6
3
6
3
6
3
6
3
6
3
6
3
6
3
6
3
External interrupts
Supply voltage (nominal)
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 5-1. Device Comparison (continued)
28069
28069-Q1
28062
28069U(2) (5)
28069M (2) (3)
28069M-Q1
28069F (2) (3)
28069F-Q1
(90 MHz)
28068U(2) (5)
28068M (2) (3)
28068F (2) (3)
(90 MHz)
28067
28067-Q1
28067U(2) (5)
(90 MHz)
28066
28066-Q1
28066U(2) (5)
(90 MHz)
28065
28065-Q1
28065U(2) (5)
(90 MHz)
28062-Q1
28062U(2) (5)
28062F (2) (3)
28062F-Q1
(90 MHz)
28064
28063
TYPE
FEATURE
28064U(2) (5)
(90 MHz)
28063U(2) (5)
(90 MHz)
(1)
Package Type
(PFP and PZP are
PowerPAD HTQFPs.
PN and PZ are LQFPs.)
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
100-
80-Pin
Pin
PN
PN
PN
PN
PN
PN
PN
PN
PZ
PZ
PZ
PZ
PZ
PZ
PZ
PZ
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
PFP
PZP
T: –40°C to
105°C
–
–
–
PZ
PN
PZ
PN
PZ
PN
PZ
PN
PZ
PN
PZ
PN
PZ
PN
PZ
PN
Temperatu S: –40°C to
re options 125°C
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
PZP
PZP
PFP
PFP
Q: –40°C to
125°C(5) (4)
(1) A type change represents a major functional feature difference in a peripheral module. Within a peripheral type, there may be minor
differences between devices that do not affect the basic functionality of the module. These device-specific differences are listed in the
C2000 Real-Time Control Peripherals Reference Guide and in the peripheral reference guides.
(2) USB is present on TMS320F2806xU, TMS320F2806xM, and TMS320F2806xF devices.
(3) TMS320F2806xM devices are InstaSPIN-MOTION™-enabled MCUs. TMS320F2806xF devices are InstaSPIN-FOC™-enabled MCUs.
For more information, see Section 10.3 for a list of InstaSPIN Technical Reference Manuals.
(4) The letter Q refers to AEC Q100 qualification for automotive applications.
(5) The Q temperature option is not available on the TMS320F2806xU devices.
5.1 Related Products
For information about similar products, see the following links:
TMS320F2802x Microcontrollers
The F2802x series offers the lowest pin-count and Flash memory size options. InstaSPIN-FOC™ versions are
available.
TMS320F2803x Microcontrollers
The F2803x series increases the pin-count and memory size options. The F2803x series also introduces the
parallel control law accelerator (CLA) option.
TMS320F2805x Microcontrollers
The F2805x series is similar to the F2803x series but adds on-chip programmable gain amplifiers (PGAs).
InstaSPIN-FOC and InstaSPIN-MOTION™ versions are available.
TMS320F2806x Microcontrollers
The F2806x series is the first to include a floating-point unit (FPU). The F2806x series also increases the pin-
count, memory size options, and the quantity of peripherals. InstaSPIN-FOC™ and InstaSPIN-MOTION™
versions are available.
TMS320F2807x Microcontrollers
The F2807x series offers the most performance, largest pin counts, flash memory sizes, and peripheral options.
The F2807x series includes the latest generation of accelerators, ePWM peripherals, and analog technology.
TMS320F28004x Microcontrollers
The F28004x series is a reduced version of the F2807x series with the latest generational enhancements. The
F28004x series is the best roadmap option for those using the F2806x series. InstaSPIN-FOC and configurable
logic block (CLB) versions are available.
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
6 Terminal Configuration and Functions
6.1 Pin Diagrams
Figure 6-1 shows the pin assignments on the 80-pin PN and PFP packages. Figure 6-2 shows the pin
assignments on the 100-pin PZ and PZP packages.
GPIO27/HRCAP2/SPISTEB/USB0DM
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
GPIO28/SCIRXDA/SDAA/TZ2
GPIO26/ECAP3/SPICLKB/USB0DP
GPIO9/EPWM5B/SCITXDB/ECAP3
VDDIO
VSS
VSS
VDD3VFL
VDD
TEST2
GPIO3/EPWM2B/SPISOMIA/COMP2OUT
GPIO2/EPWM2A
GPIO12/TZ1/SCITXDA/SPISIMOB
GPIO29/SCITXDA/SCLA/TZ3
GPIO30/CANRXA/EPWM7A
GPIO31/CANTXA/EPWM8A
GPIO25/ECAP2/SPISOMIB
VDDIO
GPIO1/EPWM1B/COMP1OUT
GPIO0/EPWM1A
GPIO15/ECAP2/SCIRXDB/SPISTEB
VREGENZ
VDD
VDD
VSS
VSS
VDDIO
ADCINB6/COMP3B/AIO14
ADCINB5
GPIO13/TZ2/SPISOMIB
GPIO14/TZ3/SCITXDB/SPICLKB
GPIO24/ECAP1/SPISIMOB
ADCINB4/COMP2B/AIO12
ADCINB2/COMP1B/AIO10
ADCINB1
GPIO22/EQEP1S/MCLKXA/SCITXDB
ADCINB0
GPIO32/SDAA/EPWMSYNCI/ADCSOCAO
GPIO33/SCLA/EPWMSYNCO/ADCSOCBO
VREFLO, VSSA
A. Pin 19: VREFHI and ADCINA0 share the same pin on the 80-pin PN and PFP devices and their use is mutually exclusive to one another.
Pin 21: VREFLO is always connected to VSSA on the 80-pin PN and PFP devices.
B. The PowerPAD is not connected to the ground on the die. To facilitate effective heat dissipation, the PowerPAD must be connected to the
ground plane of the PCB. It should not be left unconnected. For more details, see PowerPAD™ Thermally Enhanced Package.
Figure 6-1. 80-Pin PN and PFP Packages (Top View)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
GPIO41/EPWM7B/SCIRXDB
76
77
78
79
80
81
82
83
84
85
86
87
88
89
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
GPIO28/SCIRXDA/SDAA/TZ2
GPIO27/HRCAP2/EQEP2S/SPISTEB/USB0DM
GPIO9/EPWM5B/SCITXDB/ECAP3
GPIO26/ECAP3/EQEP2I/SPICLKB/USB0DP
GPIO51/EQEP1B/MDRA/TZ2
VSS
VDDIO
VSS
VDD3VFL
TEST2
VDD
GPIO40/EPWM7A/SCITXDB
GPIO3/EPWM2B/SPISOMIA/COMP2OUT
GPIO2/EPWM2A
GPIO12/TZ1/SCITXDA/SPISIMOB
GPIO29/SCITXDA/SCLA/TZ3
GPIO50/EQEP1A/MDXA/TZ1
GPIO30/CANRXA/EQEP2I/EPWM7A
GPIO31/CANTXA/EQEP2S/EPWM8A
GPIO25/ECAP2/EQEP2B/SPISOMIB
VDDIO
GPIO56/SPICLKA/EQEP2I/HRCAP3
GPIO1/EPWM1B/COMP1OUT
GPIO0/EPWM1A
GPIO15/ECAP2/SCIRXDB/SPISTEB
GPIO57/SPISTEA/EQEP2S/HRCAP4
VDD
VSS
90
91
92
93
94
95
96
97
98
99
100
VREGENZ
VDD
ADCINB7
VSS
ADCINB6/COMP3B/AIO14
ADCINB5
VDDIO
GPIO58/MCLKRA/SCITXDB/EPWM7A
ADCINB4/COMP2B/AIO12
ADCINB3
GPIO13/TZ2/SPISOMIB
GPIO14/TZ3/SCITXDB/SPICLKB
ADCINB2/COMP1B/AIO10
ADCINB1
GPIO24/ECAP1/EQEP2A/SPISIMOB
GPIO22/EQEP1S/MCLKXA/SCITXDB
ADCINB0
VREFLO
GPIO32/SDAA/EPWMSYNCI/ADCSOCAO
GPIO33/SCLA/EPWMSYNCO/ADCSOCBO
VSSA
A. The PowerPAD is not connected to the ground on the die. To facilitate effective heat dissipation, the PowerPAD must be connected to the
ground plane of the PCB. It should not be left unconnected. For more details, see PowerPAD™ Thermally Enhanced Package.
Figure 6-2. 100-Pin PZ and PZP Packages (Top View)
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Note
The PowerPAD™ should be soldered to the ground (GND) plane of the PCB because this will provide
the best thermal conduction path. For this device, the PowerPAD is not electrically shorted to the
internal die VSS; therefore, the PowerPAD does not provide an electrical connection to the PCB
ground. To make optimum use of the thermal efficiencies designed into the PowerPAD package, the
PCB must be designed with this technology in mind. A thermal land is required on the surface of the
PCB directly underneath the body of the PowerPAD. The thermal land should be soldered to the
exposed lead frame die pad of the PowerPad package; the thermal land should be as large as needed
to dissipate the required heat. An array of thermal vias should be used to connect the thermal pad to
the internal GND plane of the board. See PowerPAD™ Thermally Enhanced Package for more details
on using the PowerPAD package.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
6.2 Signal Descriptions
Section 6.2.1 describes the signals. With the exception of the JTAG pins, the GPIO function is the default at
reset, unless otherwise mentioned. The peripheral signals that are listed under them are alternate functions.
Some peripheral functions may not be available in all devices. See Table 5-1 for details. Inputs are not 5-V
tolerant. All GPIO pins are I/O/Z and have an internal pullup (PU), which can be selectively enabled or disabled
on a per-pin basis. This feature only applies to the GPIO pins. The pullups on the PWM pins are not enabled at
reset. The pullups on other GPIO pins are enabled upon reset. The AIO pins do not have an internal pullup.
Note
When the on-chip voltage regulator (VREG) is used, the GPIO19, GPIO26–27, and GPIO34–38 pins
could glitch during power up. This potential glitch will finish before the boot mode pins are read and
will not affect boot behavior. If glitching is unacceptable in an application, 1.8 V could be supplied
externally. Alternatively, adding a current-limiting resistor (for example, 470 Ω) in series with these pins
and any external driver could be considered to limit the potential for degradation to the pin and/or
external circuitry. There is no power-sequencing requirement when using an external 1.8-V supply.
However, if the 3.3-V transistors in the level-shifting output buffers of the I/O pins are powered before
the 1.8-V transistors, it is possible for the output buffers to turn on, causing a glitch to occur on the pin
during power up. To avoid this behavior, power the VDD pins before or simultaneously with the VDDIO
pins, ensuring that the VDD pins have reached 0.7 V before the VDDIO pins reach 0.7 V.
6.2.1 Signal Descriptions (1)
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
JTAG
JTAG test reset with internal pulldown (PD). TRST, when driven high, gives the scan
system control of the operations of the device. If this signal is not connected or driven
low, the device operates in its functional mode, and the test reset signals are ignored.
NOTE: TRST is an active-high test pin and must be maintained low at all times during
normal device operation. An external pulldown resistor is required on this pin. The
value of this resistor should be based on drive strength of the debugger pods applicable
to the design. A 2.2-kΩ resistor generally offers adequate protection. Because this is
application-specific, TI recommends validating each target board for proper operation of
the debugger and the application. (↓)
TRST
12
10
I
TCK
TMS
See GPIO38
I
I
See GPIO38. JTAG test clock with internal pullup. (↑)
See GPIO36. JTAG test-mode select (TMS) with internal pullup. This serial control input
is clocked into the TAP controller on the rising edge of TCK. (↑)
See GPIO36
See GPIO35
See GPIO35. JTAG test data input (TDI) with internal pullup. TDI is clocked into the
selected register (instruction or data) on a rising edge of TCK. (↑)
TDI
I
See GPIO37. JTAG scan out, test data output (TDO). The contents of the selected
register (instruction or data) are shifted out of TDO on the falling edge of TCK.
(8-mA drive)
TDO
See GPIO37
O/Z
FLASH
VDD3VFL
TEST2
46
45
37
36
3.3-V Flash Core Power Pin. This pin should be connected to 3.3 V at all times.
Test Pin. Reserved for TI. Must be left unconnected.
I/O
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PZP
PN
PFP
CLOCK
See GPIO18. Output clock derived from SYSCLKOUT. XCLKOUT is either the same
frequency, one-half the frequency, or one-fourth the frequency of SYSCLKOUT. This is
controlled by bits 1:0 (XCLKOUTDIV) in the XCLK register. At reset, XCLKOUT =
SYSCLKOUT/4. The XCLKOUT signal can be turned off by setting XCLKOUTDIV to 3.
The mux control for GPIO18 must also be set to XCLKOUT for this signal to propogate
to the pin.
XCLKOUT
See GPIO18
O/Z
See GPIO19 and GPIO38. External oscillator input. Pin source for the clock is
controlled by the XCLKINSEL bit in the XCLK register, GPIO38 is the default selection.
This pin feeds a clock from an external 3.3-V oscillator. In this case, the X1 pin, if
available, must be tied to GND and the on-chip crystal oscillator must be disabled
through bit 14 in the CLKCTL register. If a crystal or resonator is used, the XCLKIN
path must be disabled by bit 13 in the CLKCTL register.
NOTE: Designs that use the GPIO38/XCLKIN/TCK pin to supply an external clock for
normal device operation may need to incorporate some hooks to disable this path
during debug using the JTAG connector. This is to prevent contention with the TCK
signal, which is active during JTAG debug sessions. The zero-pin internal oscillators
may be used during this time to clock the device.
See GPIO19 and
GPIO38
XCLKIN
I
On-chip 1.8-V crystal-oscillator input. To use this oscillator, a quartz crystal or a ceramic
resonator must be connected across X1 and X2. In this case, the XCLKIN path must be
disabled by bit 13 in the CLKCTL register. If this pin is not used, it must be tied to GND.
X1
X2
60
59
48
47
I
On-chip crystal-oscillator output. A quartz crystal or a ceramic resonator must be
connected across X1 and X2. If X2 is not used, it must be left unconnected.
O
RESET
Device Reset (in) and Watchdog Reset (out). These devices have a built-in power-on
reset (POR) and brownout reset (BOR) circuitry. During a power-on or brownout
condition, this pin is driven low by the device. An external circuit may also drive this pin
to assert a device reset. This pin is also driven low by the MCU when a watchdog reset
occurs. During watchdog reset, the XRS pin is driven low for the watchdog reset
duration of 512 OSCCLK cycles. A resistor with a value from 2.2 kΩ to 10 kΩ should be
placed between XRS and VDDIO. If a capacitor is placed between XRS and VSS for
noise filtering, it should be 100 nF or smaller. These values will allow the watchdog to
properly drive the XRS pin to VOL within 512 OSCCLK cycles when the watchdog reset
is asserted. Regardless of the source, a device reset causes the device to terminate
execution. The program counter points to the address contained at the location
0x3F FFC0. When reset is deactivated, execution begins at the location designated by
the program counter. The output buffer of this pin is an open-drain device with an
internal pullup. (↑) If this pin is driven by an external device, it should be done using an
open-drain device.
XRS
11
9
I/OD
ADC, COMPARATOR, ANALOG I/O
ADC Group A, Channel 7 input
ADC Group A, Channel 6 input
Comparator Input 3A
ADCINA7
ADCINA6
COMP3A
AIO6
16
17
18
19
20
21
22
–
I
I
14
15
16
–
I
I/O
Digital AIO 6
ADCINA5
ADCINA4
COMP2A
AIO4
I
ADC Group A, Channel 5 input
ADC Group A, Channel 4 input
Comparator Input 2A
I
I
I/O
Digital AIO 4
ADCINA3
ADCINA2
COMP1A
AIO2
I
ADC Group A, Channel 3 input
ADC Group A, Channel 2 input
Comparator Input 1A
I
I
17
18
I/O
I
Digital AIO 2
ADCINA1
ADC Group A, Channel 1 input
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
ADC Group A, Channel 0 input.
ADCINA0
23
19
I
NOTE: VREFHI and ADCINA0 share the same pin on the 80-pin PN and PFP devices
and their use is mutually exclusive to one another.
ADC External Reference High – only used when in ADC external reference mode. See
Section 8.9.2.1.
NOTE: VREFHI and ADCINA0 share the same pin on the 80-pin PN and PFP devices
and their use is mutually exclusive to one another.
VREFHI
24
35
34
33
32
31
30
19
–
ADCINB7
ADCINB6
COMP3B
AIO14
I
ADC Group B, Channel 7 input
ADC Group B, Channel 6 input
Comparator Input 3B
I
27
26
25
–
I
I/O
Digital AIO 14
ADCINB5
ADCINB4
COMP2B
AIO12
I
ADC Group B, Channel 5 input
ADC Group B, Channel 4 input
Comparator Input 2B
I
I
I/O
Digital AIO12
ADCINB3
ADCINB2
COMP1B
AIO10
I
ADC Group B, Channel 3 input
ADC Group B, Channel 2 input
Comparator Input 1B
I
24
I
I/O
I
Digital AIO 10
ADCINB1
ADCINB0
29
28
23
22
ADC Group B, Channel 1 input
ADC Group B, Channel 0 input
I
ADC External Reference Low.
NOTE: VREFLO is always connected to VSSA on the 80-pin PN and PFP devices.
VREFLO
27
21
CPU AND I/O POWER
VDDA
VSSA
25
26
20
21
Analog Power Pin. Tie with a 2.2-μF capacitor (typical) close to the pin.
Analog Ground Pin.
NOTE: VREFLO is always connected to VSSA on the 80-pin PN and PFP devices.
3
2
14
37
63
81
91
5
12
29
51
65
72
4
CPU and Logic Digital Power Pins. When using internal VREG, place one 1.2-µF
capacitor between each VDD pin and ground. Higher value capacitors may be used.
VDD
13
38
61
79
93
4
11
30
49
63
74
3
Digital I/O Buffers Power Pin. Single supply source when VREG is enabled. Place a
decoupling capacitor on each pin. The exact value should be determined by the system
voltage regulation solution.
VDDIO
15
36
47
62
80
92
13
28
38
50
64
73
VSS
Digital Ground Pins
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
VOLTAGE REGULATOR CONTROL SIGNAL
VREGENZ
90
71
69
I
Internal VREG Enable/Disable. Pull low to enable VREG, pull high to disable VREG.
GPIO AND PERIPHERAL SIGNALS (2)
General-purpose input/output 0
Enhanced PWM1 Output A and HRPWM channel
Reserved
GPIO0
I/O/Z
O
EPWM1A
Reserved
Reserved
GPIO1
87
86
84
83
9
–
–
Reserved
I/O/Z
O
General-purpose input/output 1
Enhanced PWM1 Output B
Reserved
EPWM1B
Reserved
COMP1OUT
GPIO2
68
67
66
7
–
O
Direct output of Comparator 1
General-purpose input/output 2
Enhanced PWM2 Output A and HRPWM channel
Reserved
I/O/Z
O
EPWM2A
Reserved
Reserved
GPIO3
–
–
Reserved
I/O/Z
O
General-purpose input/output 3
Enhanced PWM2 Output B
SPI-A slave out, master in
EPWM2B
SPISOMIA
COMP2OUT
GPIO4
I/O
O
Direct output of Comparator 2
General-purpose input/output 4
Enhanced PWM3 output A and HRPWM channel
Reserved
I/O/Z
O
EPWM3A
Reserved
Reserved
GPIO5
–
–
Reserved
I/O/Z
O
General-purpose input/output 5
Enhanced PWM3 output B
EPWM3B
SPISIMOA
ECAP1
10
58
57
54
49
8
I/O
I/O
I/O/Z
O
SPI-A slave in, master out
Enhanced Capture input/output 1
General-purpose input/output 6
Enhanced PWM4 output A and HRPWM channel
External ePWM sync pulse input
External ePWM sync pulse output
General-purpose input/output 7
Enhanced PWM4 output B
GPIO6
EPWM4A
EPWMSYNCI
EPWMSYNCO
GPIO7
46
45
43
39
I
O
I/O/Z
O
EPWM4B
SCIRXDA
ECAP2
I
SCI-A receive data
I/O
I/O/Z
O
Enhanced Capture input/output 2
General-purpose input/output 8
Enhanced PWM5 output A and HRPWM channel
Reserved
GPIO8
EPWM5A
Reserved
ADCSOCAO
GPIO9
–
O
ADC start-of-conversion A
I/O/Z
O
General-purpose input/output 9
Enhanced PWM5 output B
EPWM5B
SCITXDB
ECAP3
O
SCI-B transmit data
I/O
Enhanced Capture input/output 3
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
GPIO10
I/O/Z
O
General-purpose input/output 10
EPWM6A
Reserved
ADCSOCBO
GPIO11
EPWM6B
SCIRXDB
ECAP1
Enhanced PWM6 output A and HRPWM channel
Reserved
74
73
44
95
96
88
55
52
60
59
35
75
76
70
44
42
–
O
ADC start-of-conversion B
General-purpose input/output 11
Enhanced PWM6 output B
SCI-B receive data
I/O/Z
O
I
I/O
I/O/Z
I
Enhanced Capture input/output 1
General-purpose input/output 12
Trip Zone input 1
GPIO12
TZ1
SCITXDA
SPISIMOB
GPIO13
TZ2
O
SCI-A transmit data
I/O
I/O/Z
I
SPI-B slave in, master out
General-purpose input/output 13
Trip Zone input 2
Reserved
SPISOMIB
GPIO14
TZ3
–
Reserved
I/O
I/O/Z
I
SPI-B slave out, master in
General-purpose input/output 14
Trip zone input 3
SCITXDB
SPICLKB
GPIO15
ECAP2
O
SCI-B transmit data
I/O
I/O/Z
I/O
I
SPI-B clock input/output
General-purpose input/output 15
Enhanced Capture input/output 2
SCI-B receive data
SCIRXDB
SPISTEB
GPIO16
SPISIMOA
Reserved
TZ2
I/O
I/O/Z
I/O
–
SPI-B slave transmit enable input/output
General-purpose input/output 16
SPI-A slave in, master out
Reserved
I
Trip Zone input 2
GPIO17
SPISOMIA
Reserved
TZ3
I/O/Z
I/O
–
General-purpose input/output 17
SPI-A slave out, master in
Reserved
I
Trip zone input 3
GPIO18
SPICLKA
SCITXDB
I/O/Z
I/O
O
General-purpose input/output 18
SPI-A clock input/output
SCI-B transmit data
51
41
Output clock derived from SYSCLKOUT. XCLKOUT is either the same frequency, one-
half the frequency, or one-fourth the frequency of SYSCLKOUT. This is controlled by
bits 1:0 (XCLKOUTDIV) in the XCLK register. At reset, XCLKOUT = SYSCLKOUT/4.
The XCLKOUT signal can be turned off by setting XCLKOUTDIV to 3. The mux control
for GPIO18 must also be set to XCLKOUT for this signal to propogate to the pin.
XCLKOUT
O/Z
GPIO19
I/O/Z
I
General-purpose input/output 19
External Oscillator Input. The path from this pin to the clock block is not gated by the
mux function of this pin. Care must be taken not to enable this path for clocking if it is
being used for the other peripheral functions.
XCLKIN
64
52
SPISTEA
SCIRXDB
ECAP1
I/O
I
SPI-A slave transmit enable input/output
SCI-B receive data
I/O
Enhanced Capture input/output 1
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
GPIO20
EQEP1A
MDXA
I/O/Z
I
General-purpose input/output 20
Enhanced QEP1 input A
6
5
6
O
McBSP transmit serial data
Direct output of Comparator 1
General-purpose input/output 21
Enhanced QEP1 input B
COMP1OUT
GPIO21
EQEP1B
MDRA
O
I/O/Z
I
7
98
2
I
McBSP receive serial data
Direct output of Comparator 2
General-purpose input/output 22
Enhanced QEP1 strobe
COMP2OUT
GPIO22
EQEP1S
MCLKXA
SCITXDB
GPIO23
EQEP1I
MFSXA
O
I/O/Z
I/O
I/O
O
78
1
McBSP transmit clock
SCI-B transmit data
I/O/Z
I/O
I/O
I
General-purpose input/output 23
Enhanced QEP1 index
McBSP transmit frame synch
SCI-B receive data
SCIRXDB
GPIO24
ECAP1
I/O/Z
I/O
General-purpose input/output 24
Enhanced Capture input/output 1
Enhanced QEP2 input A.
97
39
77
31
EQEP2A
I
NOTE: eQEP2 is available only in the PZ and PZP packages.
SPISIMOB
GPIO25
ECAP2
I/O
I/O/Z
I/O
SPI-B slave in, master out
General-purpose input/output 25
Enhanced Capture input/output 2
Enhanced QEP2 input B.
NOTE: eQEP2 is available only in the PZ and PZP packages.
EQEP2B
I
SPISOMIB
GPIO26
ECAP3
I/O
I/O/Z
I/O
SPI-B slave out, master in
General-purpose input/output 26
Enhanced Capture input/output 3
Enhanced QEP2 index.
NOTE: eQEP2 is available only in the PZ and PZP packages.
EQEP2I
I/O
I/O
I/O
78
62
SPICLKB
USB0DP(3)
SPI-B clock input/output
Positive Differential half of USB signal. To enable USB functionality on this pin, set the
USBIOEN bit in the GPACTRL2 register.
GPIO27
I/O/Z
I
General-purpose input/output 27
High-Resolution Input Capture 2
HRCAP2
Enhanced QEP2 strobe.
NOTE: eQEP2 is available only in the PZ and PZP packages.
EQEP2S
SPISTEB
USB0DM(3)
I/O
I/O
I/O
77
50
61
40
SPI-B slave transmit enable input/output
Negative Differential half of USB signal. To enable USB functionality on this pin, set the
USBIOEN bit in the GPACTRL2 register.
GPIO28
SCIRXDA
SDAA
I/O/Z
General-purpose input/output 28
SCI-A receive data
I
I/OD
I
I2C data open-drain bidirectional port
Trip zone input 2
TZ2
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
GPIO29
I/O/Z
General-purpose input/output 29
SCI-A transmit data
SCITXDA
SCLA
O
43
41
34
33
I/OD
I2C clock open-drain bidirectional port
Trip zone input 3
TZ3
I
I/O/Z
I
GPIO30
CANRXA
General-purpose input/output 30
CAN receive
Enhanced QEP2 index.
NOTE: eQEP2 is available only in the PZ and PZP packages.
EQEP2I
I/O
EPWM7A
GPIO31
O
I/O/Z
O
Enhanced PWM7 Output A and HRPWM channel
General-purpose input/output 31
CAN transmit
CANTXA
40
32
Enhanced QEP2 strobe.
NOTE: eQEP2 is available only in the PZ and PZP packages.
EQEP2S
I/O
EPWM8A
GPIO32
O
I/O/Z
I/OD
I
Enhanced PWM8 Output A and HRPWM channel
General-purpose input/output 32
I2C data open-drain bidirectional port
Enhanced PWM external sync pulse input
ADC start-of-conversion A
SDAA
99
100
68
79
80
55
EPWMSYNCI
ADCSOCAO
GPIO33
O
I/O/Z
I/OD
O
General-purpose input/output 33
I2C clock open-drain bidirectional port
Enhanced PWM external synch pulse output
ADC start-of-conversion B
SCLA
EPWMSYNCO
ADCSOCBO
GPIO34
O
I/O/Z
O
General-purpose input/output 34
Direct output of Comparator 2
COMP2OUT
Reserved
COMP3OUT
GPIO35
–
Reserved
O
Direct output of Comparator 3
I/O/Z
General-purpose input/output 35
JTAG test data input (TDI) with internal pullup. TDI is clocked into the selected register
(instruction or data) on a rising edge of TCK.
TDI
I
71
72
70
57
58
56
Reserved
Reserved
Reserved
GPIO36
–
–
Reserved
Reserved
–
Reserved
I/O/Z
General-purpose input/output 36
JTAG test-mode select (TMS) with internal pullup. This serial control input is clocked
into the TAP controller on the rising edge of TCK.
TMS
I
Reserved
Reserved
Reserved
GPIO37
–
–
Reserved
Reserved
–
Reserved
I/O/Z
General-purpose input/output 37
JTAG scan out, test data output (TDO). The contents of the selected register
(instruction or data) are shifted out of TDO on the falling edge of TCK (8 mA drive).
TDO
O/Z
Reserved
Reserved
Reserved
–
–
–
Reserved
Reserved
Reserved
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
GPIO38
XCLKIN
I/O/Z
I
General-purpose input/output 38
External Oscillator Input. The path from this pin to the clock block is not gated by the
mux function of this pin. Care must be taken to not enable this path for clocking if it is
being used for the other functions.
67
54
TCK
I
JTAG test clock with internal pullup
Reserved
Reserved
Reserved
Reserved
GPIO39
Reserved
Reserved
Reserved
GPIO40
EPWM7A
SCITXDB
Reserved
GPIO41
EPWM7B
SCIRXDB
Reserved
GPIO42
EPWM8A
TZ1
–
–
Reserved
–
Reserved
I/O/Z
General-purpose input/output 39
Reserved
–
66
82
76
1
53
–
–
Reserved
–
Reserved
I/O/Z
General-purpose input/output 40
Enhanced PWM7 output A and HRPWM channel
SCI-B transmit data
O
O
–
Reserved
I/O/Z
General-purpose input/output 41
Enhanced PWM7 output B
SCI-B receive data
O
–
I
–
Reserved
I/O/Z
General-purpose input/output 42
Enhanced PWM8 output A and HRPWM channel
Trip zone input 1
O
–
I
COMP1OUT
GPIO43
EPWM8B
TZ2
O
Direct output of Comparator 1
General-purpose input/output 43
Enhanced PWM8 output B
Trip zone input 2
I/O/Z
O
8
–
I
COMP2OUT
GPIO44
MFSRA
SCIRXDB
EPWM7B
GPIO50
EQEP1A
MDXA
O
Direct output of Comparator 2
General-purpose input/output 44
McBSP receive frame synch
SCI-B receive data
I/O/Z
I/O
56
42
48
53
–
I
O
Enhanced PWM7 output B
General-purpose input/output 50
Enhanced QEP1 input A
McBSP transmit serial data
Trip zone input 1
I/O/Z
I
–
O
TZ1
I
GPIO51
EQEP1B
MDRA
I/O/Z
General-purpose input/output 51
Enhanced QEP1 input B
McBSP receive serial data
Trip zone input 2
I
–
I
I
TZ2
GPIO52
EQEP1S
MCLKXA
TZ3
I/O/Z
I/O
I/O
I
General-purpose input/output 52
Enhanced QEP1 strobe
McBSP transmit clock
Trip zone input 3
–
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
PIN NO.
PIN NAME
I/O/Z
DESCRIPTION
PZ
PN
PZP
PFP
GPIO53
I/O/Z
I/O
I/O
–
General-purpose input/output 53
Enhanced QEP1 index
EQEP1I
65
69
75
85
89
94
–
–
–
–
–
–
MFSXA
McBSP transmit frame synch
Reserved
Reserved
GPIO54
I/O/Z
I/O
I
General-purpose input/output 54
SPI-A slave in, master out
Enhanced QEP2 input A
SPISIMOA
EQEP2A
HRCAP1
GPIO55
I
High-Resolution Input Capture 1
General-purpose input/output 55
SPI-A slave out, master in
Enhanced QEP2 input B
I/O/Z
I/O
I
SPISOMIA
EQEP2B
HRCAP2
GPIO56
I
High-Resolution Input Capture 2
General-purpose input/output 56
SPI-A clock input/output
I/O/Z
I/O
I/O
I
SPICLKA
EQEP2I
Enhanced QEP2 index
HRCAP3
GPIO57
High-Resolution Input Capture 3
General-purpose input/output 57
I/O/Z
I/O
I/O
I
SPISTEA
EQEP2S
HRCAP4
GPIO58
SPI-A slave transmit enable input/output
Enhanced QEP2 strobe
High-Resolution Input Capture 4
General-purpose input/output 58
McBSP receive clock
I/O/Z
I/O
O
MCLKRA
SCITXDB
EPWM7A
SCI-B transmit data
O
Enhanced PWM7 output A and HRPWM channel
(1) I = Input, O = Output, Z = High Impedance, OD = Open Drain, ↑ = Pullup, ↓ = Pulldown
(2) The GPIO function (shown in bold italics) is the default at reset. The peripheral signals that are listed under them are alternate
functions. For JTAG pins that have the GPIO functionality multiplexed, the input path to the GPIO block is always valid. The output
path from the GPIO block and the path to the JTAG block from a pin is enabled or disabled based on the condition of the TRST signal.
See the Systems Control and Interrupts chapter of the TMS320x2806x Technical Reference Manual .
(3) Depending on your USB application, additional pins may be required to maintain compliance with the USB 2.0 Specification. For more
information, see the Universal Serial Bus (USB) Controller chapter of the TMS320x2806x Technical Reference Manual .
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1) (2)
MIN
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–20
MAX
4.6
2.5
4.6
4.6
2.5
4.6
20
UNIT
VDDIO (I/O and Flash) with respect to VSS
Supply voltage
V
V
V
V
VDD with respect to VSS
Analog voltage
Input voltage
Output voltage
VDDA with respect to VSSA
VIN (3.3 V)
VIN (X1)
VO
(3)
Digital input (per pin), IIK (VIN < VSS or VIN > VDDIO
Analog input (per pin), IIKANALOG
)
–20
–20
20
20
Input clamp current
(VIN < VSSA or VIN > VDDA
)
mA
Total for all inputs, IIKTOTAL
(VIN < VSS/VSSA or VIN > VDDIO/VDDA
)
Output clamp current
Junction temperature(4)
Storage temperature(4)
IOK (VO < 0 or VO > VDDIO
)
–20
–40
–65
20
150
150
mA
°C
TJ
Tstg
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Section 7.4 is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to VSS, unless otherwise noted.
(3) Continuous clamp current per pin is ±2 mA.
(4) Long-term high-temperature storage or extended use at maximum temperature conditions may result in a reduction of overall device
life. For additional information, see Semiconductor and IC Package Thermal Metrics.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.2 ESD Ratings – Commercial
VALUE
UNIT
TMS320F2806x, TMS320F2806xM, TMS320F2806xF, and TMS320F2806xU in 100-pin PZ package
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±2000
±500
V(ESD)
Electrostatic discharge (ESD)
V
Charged-device model (CDM), per JEDEC specification JESD22-
C101 or ANSI/ESDA/JEDEC JS-002(2)
TMS320F2806x, TMS320F2806xM, TMS320F2806xF, and TMS320F2806xU in 80-pin PN package
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±2000
±500
V(ESD)
Electrostatic discharge (ESD)
V
V
V
Charged-device model (CDM), per JEDEC specification JESD22-
C101 or ANSI/ESDA/JEDEC JS-002(2)
TMS320F2806xU in 100-pin PZP package
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±2000
±500
V(ESD)
Electrostatic discharge (ESD)
Charged-device model (CDM), per JEDEC specification JESD22-
C101 or ANSI/ESDA/JEDEC JS-002(2)
TMS320F2806xU in 80-pin PFP package
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±2000
±500
V(ESD)
Electrostatic discharge (ESD)
Charged-device model (CDM), per JEDEC specification JESD22-
C101 or ANSI/ESDA/JEDEC JS-002(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 ESD Ratings – Automotive
VALUE
UNIT
TMS320F2806x, TMS320F2806xM, and TMS320F2806xF in 100-pin PZP package
Human body model (HBM), per
AEC Q100-002(1)
All pins
±2000
V(ESD)
Electrostatic discharge
Charged device model (CDM),
per AEC Q100-011
All pins
±500
±750
V
Corner pins on 100-pin PZP:
1, 25, 26, 50, 51, 75, 76, 100
TMS320F2806x, TMS320F2806xM, and TMS320F2806xF in 80-pin PFP packages
Human body model (HBM), per
AEC Q100-002(1)
All pins
±2000
V(ESD)
Electrostatic discharge
Charged device model (CDM),
per AEC Q100-011
All pins
±500
±750
V
Corner pins on 80-pin PFP:
1, 20, 21, 40, 41, 60, 61, 80
(1) AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.4 Recommended Operating Conditions
MIN
2.97
1.71
NOM
3.3
MAX
3.63
UNIT
Device supply voltage, I/O, VDDIO
V
Device supply voltage CPU, VDD (When internal VREG is
disabled and 1.8 V is supplied externally)
1.8
1.995
V
Supply ground, VSS
0
3.3
0
V
V
Analog supply voltage, VDDA
2.97
3.63
Analog ground, VSSA
V
Device clock frequency (system clock)
High-level input voltage, VIH (3.3 V)
Low-level input voltage, VIL (3.3 V)
High-level output source current, VOH = VOH(MIN) , IOH
2
2
90
MHz
V
VDDIO + 0.3
VSS – 0.3
0.8
–4
V
All GPIO/AIO pins
Group 2(1)
mA
mA
–8
Low-level output sink current, VOL = VOL(MAX), IOL
Junction temperature, TJ
All GPIO/AIO pins
Group 2(1)
4
8
T version
–40
–40
–40
105
125
125
°C
°C
S version
Ambient temperature, TA
Q version(2)
(AEC Q100 qualification)
(1) Group 2 pins are as follows: GPIO16, GPIO17, GPIO18, GPIO19, GPIO28, GPIO29, GPIO36, GPIO37.
(2) The Q temperature option is not available on the 2806xU devices.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.5 Power Consumption Summary
7.5.1 TMS320F2806x Current Consumption at 90-MHz SYSCLKOUT
VREG ENABLED
VREG DISABLED
(1)
(2)
(1)
(2)
MODE
TEST CONDITIONS
IDDIO
TYP(3)
IDDA
MAX TYP(3)
IDD3VFL
MAX TYP(3)
IDD
TYP(3)
IDDIO
IDDA
MAX TYP(3)
IDD3VFL
MAX
MAX TYP(3)
MAX TYP(3)
MAX
The following
peripheral clocks are
enabled:
•
ePWM1, ePWM2,
ePWM3, ePWM4,
ePWM5, ePWM6,
ePWM7, ePWM8
•
eCAP1, eCAP2,
eCAP3
•
•
•
•
•
•
•
•
•
eQEP1, eQEP2
eCAN
CLA
HRPWM
SCI-A, SCI-B
SPI-A, SPI-B
ADC
Operational
(Flash)
185 mA(7) 245 mA(7) 16 mA 22 mA 35 mA 40 mA 165 mA(7) 220 mA(7) 15 mA 20 mA 16 mA 22 mA 35 mA 40 mA
I2C
COMP1, COMP2,
COMP3
•
CPU-TIMER0,
CPU-TIMER1,
CPU-TIMER2
•
•
McBSP
USB
All PWM pins are
toggled at 90 kHz.
All I/O pins are left
unconnected.(4) (6)
Code is running out of
flash with 3 wait states.
XCLKOUT is turned off.
Flash is powered down.
XCLKOUT is turned off.
All peripheral clocks
are turned off.
IDLE
22 mA
9 mA
27 mA
11 mA
15 µA
15 µA
25 µA
25 µA
5 µA
5 µA
10 µA
10 µA
21 mA
8 mA
26 mA 120 µA 400 µA
10 mA 120 µA 400 µA
15 µA
15 µA
25 µA
25 µA
5 µA
5 µA
10 µA
10 µA
Flash is powered down.
Peripheral clocks are
off.
STANDBY
Flash is powered down.
Peripheral clocks are
off.
HALT
75 µA
15 µA
25 µA
5 µA
10 µA
25 µA(8)
40 µA
15 µA
25 µA
5 µA
10 µA
Input clock is disabled.
(5)
(1) IDDIO current is dependent on the electrical loading on the I/O pins.
(2) To realize the IDDA currents shown for IDLE, STANDBY, and HALT, clock to the ADC module must be turned off explicitly by writing to
the PCLKCR0 register.
(3) The TYP numbers are applicable over room temperature and nominal voltage.
(4) The following is done in a loop:
•
•
•
•
•
•
Data is continuously transmitted out of SPI-A, SPI-B, SCI-A, eCAN-A, McBSP-A, and I2C ports.
The hardware multiplier is exercised.
Watchdog is reset.
ADC is performing continuous conversion.
COMP1 and COMP2 are continuously switching voltages.
GPIO17 is toggled.
(5) If a quartz crystal or ceramic resonator is used as the clock source, the HALT mode shuts down the on-chip crystal oscillator.
(6) CLA is continuously performing polynomial calculations.
(7) For F2806x devices that do not have CLA, subtract the IDD current number for CLA (see Table 7-1) from the IDD (VREG disabled)/IDDIO
(VREG enabled) current numbers listed in Section 7.5.1 for operational mode.
(8) To realize the IDD number shown for HALT mode, the following must be done:
•
•
PLL2 must be shut down by clearing bit 2 of the PLLCTL register.
A value of 0x00FF must be written to the HRCAL register at address 0x6822.
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Note
The peripheral - I/O multiplexing implemented in the device prevents all available peripherals from
being used at the same time. This is because more than one peripheral function may share an I/O pin.
It is, however, possible to turn on the clocks to all the peripherals at the same time, although such a
configuration is not useful. If this is done, the current drawn by the device will be more than the
numbers specified in the current consumption tables.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.5.2 Reducing Current Consumption
The 2806x devices incorporate a method to reduce the device current consumption. Because each peripheral
unit has an individual clock-enable bit, significant reduction in current consumption can be achieved by turning
off the clock to any peripheral module that is not used in a given application. Furthermore, any one of the three
low-power modes could be taken advantage of to reduce the current consumption even further. Table 7-1
indicates the typical reduction in current consumption achieved by turning off the clocks.
Table 7-1. Typical Current Consumption by Various
Peripherals (at 90 MHz) (1)
PERIPHERAL
MODULE(3)
IDD CURRENT
REDUCTION (mA)
ADC
2(2)
I2C
3
ePWM
2
eCAP
2
eQEP
2
SCI
SPI
2
2
COMP/DAC
HRPWM
1
3
HRCAP
3
USB
12
1
CPU-TIMER
Internal zero-pin oscillator
CAN
0.5
2.5
20
6
CLA
McBSP
(1) All peripheral clocks (except CPU Timer clock) are disabled
upon reset. Writing to or reading from peripheral registers is
possible only after the peripheral clocks are turned on.
(2) This number represents the current drawn by the digital portion
of the ADC module. Turning off the clock to the ADC module
results in the elimination of the current drawn by the analog
portion of the ADC (IDDA) as well.
(3) For peripherals with multiple instances, the current quoted is per
module. For example, the 2 mA value quoted for ePWM is for
one ePWM module.
Note
IDDIO current consumption is reduced by 15 mA (typical) when XCLKOUT is turned off.
Note
The baseline IDD current (current when the core is executing a dummy loop with no peripherals
enabled) is 40 mA, typical. To arrive at the IDD current for a given application, the current-drawn by the
peripherals (enabled by that application) must be added to the baseline IDD current.
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Following are other methods to reduce power consumption further:
•
The flash module may be powered down if code is run off SARAM. This results in a current reduction of 18
mA (typical) in the VDD rail and 13 mA (typical) in the VDDIO rail.
•
•
Savings in IDDIO may be realized by disabling the pullups on pins that assume an output function.
To realize the lowest VDDA current consumption in a low-power mode, see the respective analog chapter of
the TMS320x2806x Technical Reference Manual to ensure each module is powered down as well.
Power savings can be achieved by powering down the flash. This must be done by code running off RAM
(not flash).
•
7.5.3 Current Consumption Graphs (VREG Enabled)
250
200
150
100
50
IDDIO
IDDA
IDD3VFL
Total
0
10
20
30
40
50
60
70
80
90
SYSCLKOUT (MHz)
Figure 7-1. Typical Operational Current (Flash) Versus Frequency (Internal VREG)
900
800
700
600
500
400
300
200
100
0
10
20
30
40
50
60
70
80
90
SYSCLKOUT (MHz)
Figure 7-2. Typical Operational Power Versus Frequency (Internal VREG)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.6 Electrical Characteristics
over recommended operating conditions (unless otherwise noted)(1)
PARAMETER
TEST CONDITIONS
MIN
2.4
TYP
MAX UNIT
IOH = IOH MAX
IOH = 50 μA
VOH
VOL
High-level output voltage
Low-level output voltage
V
VDDIO – 0.2
IOL = IOL MAX
0.4
–205
–375
V
All GPIO
–80 –140
Pin with pullup
VDDIO = 3.3 V, VIN = 0 V
enabled
Input current
(low level)
XRS pin
–230 –300
IIL
μA
Pin with pulldown
enabled
VDDIO = 3.3 V, VIN = 0 V
VDDIO = 3.3 V, VIN = VDDIO
VDDIO = 3.3 V, VIN = VDDIO
VO = VDDIO or 0 V
±2
±2
80
Pin with pullup
enabled
Input current
(high level)
IIH
μA
Pin with pulldown
enabled
28
50
Output current, pullup or pulldown
disabled
IOZ
CI
±2 μA
pF
Input capacitance
2
2.78
35
VDDIO BOR trip point
VDDIO BOR hysteresis
Falling VDDIO
2.50
400
2.96
V
mV
Supervisor reset release delay
time
Time after BOR/POR/OVR event is removed to XRS
release
800 μs
V
VREG VDD output
Internal VREG on
1.9
(1) When the on-chip VREG is used, its output is monitored by the POR/BOR circuit, which will reset the device should the core voltage
(VDD) go out of range.
Copyright © 2021 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.7 Thermal Resistance Characteristics
7.7.1 PFP PowerPAD Package
°C/W(1)
9.4
AIR FLOW (lfm)(2)
RΘJC
RΘJB
Junction-to-case thermal resistance
Junction-to-board thermal resistance
0
4.6
0
25.8
16.3
15.2
13.6
0.3
0
150
250
500
0
RΘJA
(High k PCB)
Junction-to-free air thermal resistance
Junction-to-package top
0.4
150
250
500
0
PsiJT
0.4
0.5
4.6
4.4
150
250
500
PsiJB
Junction-to-board
4.3
4.3
(1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a
JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/
JEDEC standards:
•
•
•
•
JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
(2) lfm = linear feet per minute
7.7.2 PZP PowerPAD Package
°C/W(1)
9.4
AIR FLOW (lfm)(2)
RΘJC
RΘJB
Junction-to-case thermal resistance
0
Junction-to-board thermal resistance
4.4
0
24.4
15.1
13.9
12.4
0.3
0
150
250
500
0
RΘJA
(High k PCB)
Junction-to-free air thermal resistance
0.4
150
250
500
0
PsiJT
Junction-to-package top
Junction-to-board
0.4
0.5
4.5
4.2
150
250
500
PsiJB
4.2
4.2
(1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a
JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/
JEDEC standards:
•
•
•
•
JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
(2) lfm = linear feet per minute
Copyright © 2021 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.7.3 PN Package
°C/W(1)
7.9
AIR FLOW (lfm)(2)
RΘJC
RΘJB
Junction-to-case thermal resistance
0
Junction-to-board thermal resistance
15.6
41.1
31.2
29.7
27.5
0.4
0
0
150
250
500
0
RΘJA
(High k PCB)
Junction-to-free air thermal resistance
0.6
150
250
500
0
PsiJT
Junction-to-package top
Junction-to-board
0.7
0.9
15.3
14.6
14.4
14.1
150
250
500
PsiJB
(1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a
JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/
JEDEC standards:
•
•
•
•
JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
(2) lfm = linear feet per minute
7.7.4 PZ Package
°C/W(1)
7.2
AIR FLOW (lfm)(2)
RΘJC
RΘJB
Junction-to-case thermal resistance
0
Junction-to-board thermal resistance
19.6
42.2
32.4
30.9
28.7
0.4
0
0
150
250
500
0
RΘJA
(High k PCB)
Junction-to-free air thermal resistance
0.6
150
250
500
0
PsiJT
Junction-to-package top
Junction-to-board
0.7
0.9
19.1
18.2
17.9
14.1
150
250
500
PsiJB
(1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a
JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/
JEDEC standards:
•
•
•
•
JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
(2) lfm = linear feet per minute
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.8 Thermal Design Considerations
Based on the end application design and operational profile, the IDD and IDDIO currents could vary. Systems that
exceed the recommended maximum power dissipation in the end product may require additional thermal
enhancements. Ambient temperature (TA) varies with the end application and product design. The critical factor
that affects reliability and functionality is TJ, the junction temperature, not the ambient temperature. Hence, care
should be taken to keep TJ within the specified limits. Tcase should be measured to estimate the operating
junction temperature TJ. Tcase is normally measured at the center of the package top-side surface. The thermal
application report Semiconductor and IC Package Thermal Metrics helps to understand the thermal metrics and
definitions.
7.9 Debug Probe Connection Without Signal Buffering for the MCU
Figure 7-3 shows the connection between the MCU and JTAG header for a single-processor configuration. If the
distance between the JTAG header and the MCU is greater than 6 inches, the emulation signals must be
buffered. If the distance is less than 6 inches, buffering is typically not needed. Figure 7-3 shows the simpler, no-
buffering situation. For the pullup and pulldown resistor values, see Section 6.2.
6 inches or less
VDDIO
VDDIO
13
14
2
5
EMU0
EMU1
TRST
TMS
PD
4
6
8
TRST
TMS
TDI
GND
1
GND
GND
GND
GND
3
TDI
7
10
12
TDO
TCK
TDO
11
9
TCK
TCK_RET
MCU
JTAG Header
A. See Figure 8-54 for JTAG/GPIO multiplexing.
Figure 7-3. Debug Probe Connection Without Signal Buffering for the MCU
Note
The 2806x devices do not have EMU0/EMU1 pins. For designs that have a JTAG Header onboard,
the EMU0/EMU1 pins on the header must be tied to VDDIO through a 4.7-kΩ (typical) resistor.
Copyright © 2021 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.10 Parameter Information
7.10.1 Timing Parameter Symbology
Timing parameter symbols used are created in accordance with JEDEC Standard 100. To shorten the symbols,
some of the pin names and other related terminology have been abbreviated as follows:
LOWERCASE SUBSCRIPTS AND THEIR MEANINGS:
LETTERS AND SYMBOLS AND THEIR MEANINGS:
a
c
d
f
access time
cycle time (period)
delay time
H
L
High
Low
V
X
Z
Valid
fall time
Unknown, changing, or don't care level
High impedance
h
r
hold time
rise time
su
t
setup time
transition time
valid time
v
w
pulse duration (width)
7.10.2 General Notes on Timing Parameters
All output signals from the 28x devices (including XCLKOUT) are derived from an internal clock such that all
output transitions for a given half-cycle occur with a minimum of skewing relative to each other.
The signal combinations shown in the following timing diagrams may not necessarily represent actual cycles. For
actual cycle examples, see the appropriate cycle description section of this document.
7.11 Test Load Circuit
This test load circuit is used to measure all switching characteristics provided in this document.
Tester Pin Electronics
Data Sheet Timing Reference Point
W
3.5 nH
Output
Under
Test
42
Transmission Line
(A)
Z0 = 50 W
Device Pin(B)
4.0 pF
1.85 pF
A. Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin.
B. The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects
must be taken into account. A transmission line with a delay of 2 ns or longer can be used to produce the desired transmission line
effect. The transmission line is intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns or longer)
from the data sheet timing.
Figure 7-4. 3.3-V Test Load Circuit
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
33
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.12 Power Sequencing
There is no power sequencing requirement needed to ensure the device is in the proper state after reset or to
prevent the I/Os from glitching during power up or power down (GPIO19, GPIO26–27, GPIO34–38 do not have
glitch-free I/Os). No voltage larger than a diode drop (0.7 V) above VDDIO should be applied to any digital pin (for
analog pins, this value is 0.7 V above VDDA) before powering up the device. Voltages applied to pins on an
unpowered device can bias internal p-n junctions in unintended ways and produce unpredictable results.
VDDIO, VDDA
(3.3 V)
VDD (1.8 V)
INTOSC1
tINTOSCST
X1/X2
tOSCST
(B)
(A)
XCLKOUT
User-code dependent
t
w(RSL1)
XRS(D)
Address/data valid, internal boot-ROM code execution phase
Address/Data/
Control
(Internal)
User-code execution phase
User-code dependent
t
d(EX)
(C)
h(boot-mode)
t
Boot-Mode
Pins
GPIO pins as input
Peripheral/GPIO function
Based on boot code
Boot-ROM execution starts
(E)
GPIO pins as input [state depends on internal pullup/pulldown (PU/PD)]
I/O Pins
User-code dependent
A. Upon power up, SYSCLKOUT is OSCCLK/4. Because the XCLKOUTDIV bits in the XCLK register come up with a reset state of 0,
SYSCLKOUT is further divided by 4 before it appears at XCLKOUT. XCLKOUT = OSCCLK/16 during this phase.
B. Boot ROM configures the DIVSEL bits for /1 operation. XCLKOUT = OSCCLK/4 during this phase. XCLKOUT will not be visible at the
pin until explicitly configured by user code.
C. After reset, the boot ROM code samples Boot Mode pins. Based on the status of the Boot Mode pin, the boot code branches to
destination memory or boot code function. If boot ROM code executes after power-on conditions (in debugger environment), the boot
code execution time is based on the current SYSCLKOUT speed. The SYSCLKOUT will be based on user environment and could be
with or without PLL enabled.
D. Using the XRS pin is optional due to the on-chip POR circuitry.
E. The internal pullup or pulldown will take effect when BOR is driven high.
Figure 7-5. Power-on Reset
Copyright © 2021 Texas Instruments Incorporated
34
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.12.1 Reset ( XRS) Timing Requirements
MIN
1000tc(SCO)
32tc(OSCCLK)
MAX
UNIT
cycles
cycles
th(boot-mode)
tw(RSL2)
Hold time for boot-mode pins
Pulse duration, XRS low on warm reset
7.12.2 Reset ( XRS) Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
TYP
MAX
UNIT
μs
tw(RSL1)
tw(WDRS)
td(EX)
Pulse duration, XRS driven by device
600
Pulse duration, reset pulse generated by watchdog
Delay time, address/data valid after XRS high
Start-up time, internal zero-pin oscillator
On-chip crystal-oscillator start-up time
512tc(OSCCLK)
cycles
cycles
μs
32tc(OSCCLK)
tINTOSCST
3
(1)
tOSCST
1
10
ms
(1) Dependent on crystal/resonator and board design.
INTOSC1
X1/X2
XCLKOUT
User-Code Dependent
t
w(RSL2)
XRS
User-Code Execution Phase
t
d(EX)
Address/Data/
User-Code Execution
Control
(Internal)
(A)
t
Boot-ROM Execution Starts
GPIO Pins as Input
h(boot-mode)
Boot-Mode
Pins
Peripheral/GPIO Function
User-Code Dependent
Peripheral/GPIO Function
User-Code Execution Starts
I/O Pins
GPIO Pins as Input (State Depends on Internal PU/PD)
User-Code Dependent
A. After reset, the Boot ROM code samples BOOT Mode pins. Based on the status of the Boot Mode pin, the boot code branches to
destination memory or boot code function. If Boot ROM code executes after power-on conditions (in debugger environment), the Boot
code execution time is based on the current SYSCLKOUT speed. The SYSCLKOUT will be based on user environment and could be
with or without PLL enabled.
Figure 7-6. Warm Reset
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
35
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Figure 7-7 shows an example for the effect of writing into PLLCR register. In the first phase, PLLCR = 0x0004
and SYSCLKOUT = OSCCLK × 2. The PLLCR is then written with 0x0008. Right after the PLLCR register is
written, the PLL lock-up phase begins. During this phase, SYSCLKOUT = OSCCLK/2. After the PLL lock-up is
complete, SYSCLKOUT reflects the new operating frequency, OSCCLK × 4.
OSCCLK
Write to PLLCR
SYSCLKOUT
OSCCLK * 2
OSCCLK/2
OSCCLK * 4
(CPU frequency while PLL is stabilizing
with the desired frequency. This period
(PLL lock-up time tp) is 1 ms long.)
(Current CPU
Frequency)
(Changed CPU frequency)
Figure 7-7. Example of Effect of Writing Into PLLCR Register
Copyright © 2021 Texas Instruments Incorporated
36
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.13 Clock Specifications
7.13.1 Device Clock Table
This section provides the timing requirements and switching characteristics for the various clock options
available on the 2806x MCUs. Section 7.13.1.1 lists the cycle times of various clocks.
7.13.1.1 2806x Clock Table and Nomenclature (90-MHz Devices)
MIN
11.11
2
NOM
MAX UNIT
tc(SCO), Cycle time
Frequency
500
90
ns
MHz
ns
SYSCLKOUT
LSPCLK(1)
ADC clock
tc(LCO), Cycle time
Frequency
11.11
44.4(2)
22.5(2)
90
45
MHz
ns
tc(ADCCLK), Cycle time
Frequency
22.22
MHz
(1) Lower LSPCLK will reduce device power consumption.
(2) This is the default reset value if SYSCLKOUT = 90 MHz.
7.13.1.2 Device Clocking Requirements/Characteristics
MIN
50
NOM
MAX UNIT
tc(OSC), Cycle time
Frequency
200
20
ns
MHz
ns
On-chip oscillator (X1/X2 pins)
(Crystal/Resonator)
5
tc(CI), Cycle time (C8)
Frequency
33.3
5
200
30
External oscillator/clock source
(XCLKIN pin) — PLL Enabled
MHz
ns
tc(CI), Cycle time (C8)
Frequency
11.11
4
250
90
External oscillator/clock source
(XCLKIN pin) — PLL Disabled
MHz
Limp mode SYSCLKOUT
(with /2 enabled)
Frequency range
1 to 5
MHz
tc(XCO), Cycle time (C1)
44.44
0.5
2000
22.5
1
ns
MHz
ms
XCLKOUT
Frequency
tp
PLL lock time(1)
(1) The PLLLOCKPRD register must be updated based on the number of OSCCLK cycles. If the zero-pin internal oscillators (10 MHz) are
used as the clock source, then the PLLLOCKPRD register must be written with a value of 10,000 (minimum).
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
37
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.13.1.3 Internal Zero-Pin Oscillator (INTOSC1/INTOSC2) Characteristics
PARAMETER
Internal zero-pin oscillator 1 (INTOSC1) at 30°C(1) (2)
Internal zero-pin oscillator 2 (INTOSC2) at 30°C(1) (2)
Step size (coarse trim)
MIN
TYP
10.000
10.000
55
MAX
UNIT
MHz
Frequency
Frequency
MHz
kHz
Step size (fine trim)
14
kHz
Temperature drift(3)
3.03
4.85
kHz/°C
Hz/mV
Voltage (VDD) drift(3)
175
(1) In order to achieve better oscillator accuracy (10 MHz ± 1% or better) than shown, refer to the Oscillator Compensation Guide.
(2) Frequency range ensured only when VREG is enabled, VREGENZ = VSS
.
(3) Output frequency of the internal oscillators follows the direction of both the temperature gradient and voltage (VDD) gradient. For
example:
•
•
Increase in temperature will cause the output frequency to increase per the temperature coefficient.
Decrease in voltage (VDD) will cause the output frequency to decrease per the voltage coefficient.
10.6
10.5
10.4
10.3
10.2
10.1
10
9.9
9.8
9.7
9.6
–40
–30
–20
–10
0
10
20
30
40
50
60
70
80
90
100
110
120
Typical
Max
Temperature (°C)
Figure 7-8. Zero-Pin Oscillator Frequency Movement With Temperature
Copyright © 2021 Texas Instruments Incorporated
38
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.13.2 Clock Requirements and Characteristics
7.13.2.1 XCLKIN Timing Requirements – PLL Enabled
NO.
MIN
MAX UNIT
C9
tf(CI)
Fall time, XCLKIN
6
6
ns
ns
C10 tr(CI)
Rise time, XCLKIN
C11 tw(CIL)
C12 tw(CIH)
Pulse duration, XCLKIN low as a percentage of tc(OSCCLK)
Pulse duration, XCLKIN high as a percentage of tc(OSCCLK)
45%
45%
55%
55%
7.13.2.2 XCLKIN Timing Requirements – PLL Disabled
NO.
MIN
MAX UNIT
Up to 20 MHz
6
C9
tf(CI)
Fall time, XCLKIN
Rise time, XCLKIN
ns
2
20 MHz to 90 MHz
Up to 20 MHz
6
C10 tr(CI)
ns
2
20 MHz to 90 MHz
C11 tw(CIL)
C12 tw(CIH)
Pulse duration, XCLKIN low as a percentage of tc(OSCCLK)
Pulse duration, XCLKIN high as a percentage of tc(OSCCLK)
45%
45%
55%
55%
The possible configuration modes are shown in Table 8-15.
7.13.2.3 XCLKOUT Switching Characteristics (PLL Bypassed or Enabled)
over recommended operating conditions (unless otherwise noted)(1) (2)
NO.
C3
C4
C5
C6
PARAMETER
MIN
MAX
UNIT
ns
tf(XCO)
Fall time, XCLKOUT
Rise time, XCLKOUT
5
5
tr(XCO)
ns
tw(XCOL)
tw(XCOH)
Pulse duration, XCLKOUT low
Pulse duration, XCLKOUT high
H – 2
H – 2
H + 2
H + 2
ns
ns
(1) A load of 40 pF is assumed for these parameters.
(2) H = 0.5tc(XCO)
C10
C9
C8
(A)
XCLKIN
C6
C3
C1
C4
C5
(B)
XCLKOUT
A. The relationship of XCLKIN to XCLKOUT depends on the divide factor chosen. The waveform relationship shown is intended to illustrate
the timing parameters only and may differ based on actual configuration.
B. XCLKOUT configured to reflect SYSCLKOUT.
Figure 7-9. Clock Timing
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
39
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.14 Flash Timing
7.14.1 Flash/OTP Endurance for T Temperature Material
ERASE/PROGRAM
MIN
20000
TYP
MAX
UNIT
TEMPERATURE(1)
0°C to 105°C (ambient)
0°C to 30°C (ambient)
Nf
Flash endurance for the array (write/erase cycles)
50000
cycles
write
NOTP OTP endurance for the array (write cycles)
1
(1) Write/erase operations outside of the temperature ranges indicated are not specified and may affect the endurance numbers.
7.14.2 Flash/OTP Endurance for S Temperature Material
ERASE/PROGRAM
MIN
TYP
MAX
UNIT
TEMPERATURE(1)
0°C to 125°C (ambient)
0°C to 30°C (ambient)
Nf
Flash endurance for the array (write/erase cycles)
20000
50000
cycles
write
NOTP OTP endurance for the array (write cycles)
1
(1) Write/erase operations outside of the temperature ranges indicated are not specified and may affect the endurance numbers.
7.14.3 Flash/OTP Endurance for Q Temperature Material
ERASE/PROGRAM
MIN
TYP
MAX
UNIT
TEMPERATURE(1) (2)
–40°C to 125°C (ambient)
–40°C to 30°C (ambient)
Nf
Flash endurance for the array (write/erase cycles)
20000
50000
cycles
write
NOTP OTP endurance for the array (write cycles)
1
(1) Write/erase operations outside of the temperature ranges indicated are not specified and may affect the endurance numbers.
(2) The "Q" temperature option is not available on the 2806xU devices.
7.14.4 Flash Parameters at 90-MHz SYSCLKOUT
TEST
CONDITIONS
PARAMETER
MIN
TYP
MAX UNIT
16-Bit Word
16K Sector
8K Sector
4K Sector
16K Sector
8K Sector
4K Sector
50
500
250
125
2
μs
2000(2)
ms
ms
ms
Program Time(1)
Erase Time(3)
2000(2)
2000(2)
15(2)
2
15(2)
s
2
15(2)
(4)
IDDP
VDD current consumption during Erase/Program cycle
VDDIO current consumption during Erase/Program cycle
VDDIO current consumption during Erase/Program cycle
80
60
120
VREG disabled
VREG enabled
mA
mA
(4)
IDDIOP
(4)
IDDIOP
(1) Program time is at the maximum device frequency. The programming time indicated in this table is applicable only when all the
required code/data is available in the device RAM, ready for programming. Program time includes overhead of the flash state machine
but does not include the time to transfer the following into RAM:
•
•
•
the code that uses flash API to program the flash
the Flash API itself
Flash data to be programmed
(2) The parameters mentioned in the MAX column are for the first 100 Erase/Program cycles.
(3) The on-chip flash memory is in an erased state when the device is shipped from TI. As such, erasing the flash memory is not required
before programming, when programming the device for the first time. However, the erase operation is needed on all subsequent
programming operations.
(4) Typical parameters as seen at room temperature including function call overhead, with all peripherals off. It is important to maintain a
stable power supply during the entire flash programming process. It is conceivable that device current consumption during flash
programming could be higher than normal operating conditions. The power supply used should ensure VMIN on the supply rails at all
times, as specified in the Recommended Operating Conditions of the data sheet. Any brownout or interruption to power during erasing/
programming could potentially corrupt the password locations and lock the device permanently. Powering a target board (during flash
Copyright © 2021 Texas Instruments Incorporated
40
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
programming) through the USB port is not recommended, as the port may be unable to respond to the power demands placed during
the programming process.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
41
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
7.14.5 Flash/OTP Access Timing
PARAMETER
MIN
36
MAX UNIT
ta(fp)
Paged Flash access time
Random Flash access time
OTP access time
ns
ns
ns
ta(fr)
36
ta(OTP)
60
7.14.6 Flash Data Retention Duration
PARAMETER
TEST CONDITIONS
TJ = 55°C
MIN
15
MAX UNIT
tretention
Data retention duration
years
Table 7-2. Minimum Required Flash/OTP Wait States at Different Frequencies
SYSCLKOUT
SYSCLKOUT
(ns)
PAGE
RANDOM
OTP
WAIT STATE
(MHz)
WAIT STATE(1)
WAIT STATE(1)
90
11.11
12.5
3
2
2
2
1
1
1
1
1
1
3
2
2
2
1
1
1
1
1
1
5
4
4
3
3
2
2
2
2
1
80
70
14.29
16.67
18.18
20
60
55
50
45
22.22
25
40
35
28.57
33.33
30
(1) Page and random wait state must be ≥ 1.
The equations to compute the Flash page wait state and random wait state in Table 7-2 are as follows:
é
ê
ë
ù
æ
ç
ç
è
ö
÷
÷
ø
ta(f ×p)
Flash Page Wait State =
-1 round up to the next highest integer, or 1, whichever is larger
ú
tc(SCO)
ê
ú
û
é
ê
ë
ù
æ
ç
ç
è
ö
÷
÷
ø
ta(f ×r)
Flash Random Wait State =
-1 round up to the next highest integer, or 1, whichever is larger
ú
tc(SCO)
ê
ú
û
The equation to compute the OTP wait state in Table 7-2 is as follows:
é
ê
ë
ù
æ
ç
ç
è
ö
÷
÷
ø
ta(OTP)
OTP Wait State =
-1 round up to the next highest integer, or 1, whichever is larger
ú
tc(SCO)
ê
ú
û
Copyright © 2021 Texas Instruments Incorporated
42
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8 Detailed Description
8.1 Overview
8.1.1 CPU
The 2806x (C28x) family is a member of the TMS320C2000™ microcontroller (MCU) platform. The C28x-based
controllers have the same 32-bit fixed-point architecture as existing C28x MCUs. Each C28x-based controller,
including the 2806x device, is a very efficient C/C++ engine, enabling users to develop not only their system
control software in a high-level language, but also enabling development of math algorithms using C/C++. The
device is as efficient at MCU math tasks as it is at system control tasks that typically are handled by
microcontroller devices. This efficiency removes the need for a second processor in many systems. The 32 × 32-
bit MAC 64-bit processing capabilities enable the controller to handle higher numerical resolution problems
efficiently. Add to this the fast interrupt response with automatic context save of critical registers, resulting in a
device that is capable of servicing many asynchronous events with minimal latency. The device has an 8-level-
deep protected pipeline with pipelined memory accesses. This pipelining enables it to execute at high speeds
without resorting to expensive high-speed memories. Special branch-look-ahead hardware minimizes the latency
for conditional discontinuities. Special store conditional operations further improve performance.
8.1.2 Control Law Accelerator (CLA)
The C28x CLA is a single-precision (32-bit) floating-point unit that extends the capabilities of the C28x CPU by
adding parallel processing. The CLA is an independent processor with its own bus structure, fetch mechanism,
and pipeline. Eight individual CLA tasks, or routines, can be specified. Each task is started by software or a
peripheral such as the ADC, ePWM, eCAP, eQEP, or CPU Timer 0. The CLA executes one task at a time to
completion. When a task completes, the main CPU is notified by an interrupt to the PIE and the CLA
automatically begins the next highest-priority pending task. The CLA can directly access the ADC Result
registers, ePWM+HRPWM, eCAP, and eQEP registers. Dedicated message RAMs provide a method to pass
additional data between the main CPU and the CLA.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
43
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.3 Viterbi, Complex Math, CRC Unit (VCU)
The C28x VCU enhances the processing power of C2000™ devices by adding additional assembly instructions
to target complex math, Viterbi decode, and CRC calculations. The VCU instructions accelerate many
applications, including the following:
•
Orthogonal frequency-division multiplex (OFDM) used in the PRIME and G3 standards for power line
communications
•
•
•
Short-range radar complex math calculations
Power calculations
Memory and data communication packet checks (CRC)
The VCU features include:
•
Instructions to support Cyclic Redundancy Checks (CRCs), which is a polynomial code checksum.
– CRC8
– CRC16
– CRC32
•
Instructions to support a flexible software implementation of a Viterbi decoder
– Branch metric calculations for a code rate of 1/2 or 1/3
– Add-Compare Select or Viterbi Butterfly in five cycles per butterfly
– Traceback in three cycles per stage
– Easily supports a constraint length of K = 7 used in PRIME and G3 standards
Complex math arithmetic unit
– Single-cycle Add or Subtract
– 2-cycle multiply
– 2-cycle multiply and accumulate (MAC)
– Single-cycle repeat MAC
Independent register space
•
•
8.1.4 Memory Bus (Harvard Bus Architecture)
As with many MCU-type devices, multiple buses are used to move data between the memories and peripherals
and the CPU. The memory bus architecture contains a program read bus, data read bus, and data write bus.
The program read bus consists of 22 address lines and 32 data lines. The data read and write buses consist of
32 address lines and 32 data lines each. The 32-bit-wide data buses enable single cycle 32-bit operations. The
multiple bus architecture, commonly termed Harvard Bus, enables the C28x to fetch an instruction, read a data
value and write a data value in a single cycle. All peripherals and memories attached to the memory bus
prioritize memory accesses. Generally, the priority of memory bus accesses can be summarized as follows:
Highest:
Data Writes
Program Writes
Data Reads
Program Reads
Fetches
(Simultaneous data and program writes cannot occur on the memory bus.)
(Simultaneous data and program writes cannot occur on the memory bus.)
(Simultaneous program reads and fetches cannot occur on the memory bus.)
(Simultaneous program reads and fetches cannot occur on the memory bus.)
Lowest:
Copyright © 2021 Texas Instruments Incorporated
44
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.5 Peripheral Bus
To enable migration of peripherals between various Texas Instruments (TI) MCU family of devices, the devices
adopt a peripheral bus standard for peripheral interconnect. The peripheral bus bridge multiplexes the various
buses that make up the processor Memory Bus into a single bus consisting of 16 address lines and 16 or 32
data lines and associated control signals. Three versions of the peripheral bus are supported. One version
supports only 16-bit accesses (called peripheral frame 2). Another version supports both 16- and 32-bit
accesses (called peripheral frame 1).
8.1.6 Real-Time JTAG and Analysis
1
The devices implement the standard IEEE 1149.1 JTAG interface for in-circuit based debug. Additionally, the
devices support real-time mode of operation allowing modification of the contents of memory, peripheral, and
register locations while the processor is running and executing code and servicing interrupts. The user can also
single step through non-time-critical code while enabling time-critical interrupts to be serviced without
interference. The device implements the real-time mode in hardware within the CPU. This is a feature unique to
the 28x family of devices, requiring no software monitor. Additionally, special analysis hardware is provided that
allows setting of hardware breakpoint or data/address watch-points and generating various user-selectable
break events when a match occurs.
8.1.7 Flash
The F28069, F28069F, F28069M, F28068F, F28068M, F28067, and F28066 devices contain 128K × 16 of
embedded flash memory, segregated into eight 16K × 16 sectors. The F28065, F28064, F28063, F28062, and
F28062F devices contain 64K × 16 of embedded flash memory, segregated into eight 8K × 16 sectors. All
devices also contain a single 1K × 16 of OTP memory at address range 0x3D 7800 to 0x3D 7BF9. The user can
individually erase, program, and validate a flash sector while leaving other sectors untouched. However, it is not
possible to use one sector of the flash or the OTP to execute flash algorithms that erase or program other
sectors. Special memory pipelining is provided to enable the flash module to achieve higher performance. The
flash/OTP is mapped to both program and data space; therefore, it can be used to execute code or store data
information. Addresses 0x3F 7FF0 to 0x3F 7FF5 are reserved for data variables and should not contain program
code.
Note
The Flash and OTP wait states can be configured by the application. This allows applications running
at slower frequencies to configure the flash to use fewer wait states.
Flash effective performance can be improved by enabling the flash pipeline mode in the Flash options
register. With this mode enabled, effective performance of linear code execution will be much faster
than the raw performance indicated by the wait-state configuration alone. The exact performance gain
when using the Flash pipeline mode is application-dependent.
For more information on the Flash options, Flash wait state, and OTP wait-state registers, see the
Systems Control and Interrupts chapter of the TMS320x2806x Technical Reference Manual .
1
IEEE Standard 1149.1-1990 Standard Test Access Port and Boundary Scan Architecture
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
45
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.8 M0, M1 SARAMs
All devices contain these two blocks of single-access memory, each 1K × 16 in size. The stack pointer points to
the beginning of block M1 on reset. The M0 and M1 blocks, like all other memory blocks on C28x devices, are
mapped to both program and data space. Hence, the user can use M0 and M1 to execute code or for data
variables. The partitioning is performed within the linker. The C28x device presents a unified memory map to the
programmer. This makes for easier programming in high-level languages.
8.1.9 L4 SARAM, and L0, L1, L2, L3, L5, L6, L7, and L8 DPSARAMs
The device contains up to 48K × 16 of single-access RAM. To ascertain the exact size for a given device, see
the device-specific memory map figures in Section 8.2. This block is mapped to both program and data space.
L0 is 2K in size. L1 and L2 are each 1K in size. L3 is 4K in size. L4, L5, L6, L7, and L8 are each 8K in size. L0,
L1, and L2 are shared with the CLA, which can use these blocks for its data space. L3 is shared with the CLA,
which can use this block for its program space. L5, L6, L7, and L8 are shared with the DMA, which can use
these blocks for its data space. DPSARAM refers to the dual-port configuration of these blocks.
8.1.10 Boot ROM
The Boot ROM is factory-programmed with boot-loading software. Boot-mode signals are provided to tell the
bootloader software what boot mode to use on power up. The user can select to boot normally or to download
new software from an external connection or to select boot software that is programmed in the internal Flash/
ROM. The Boot ROM also contains standard tables, such as SIN/COS waveforms, for use in math-related
algorithms.
Table 8-1. Boot Mode Selection
GPIO34/COMP2OUT/
MODE
GPIO37/TDO
TRST
MODE
COMP3OUT
3
2
1
1
0
0
x
1
0
1
0
x
0
0
0
0
1
GetMode
Wait (see Section 8.1.11 for description)
1
SCI
0
Parallel IO
Emulation Boot
EMU
8.1.10.1 Emulation Boot
When the debug probe is connected, the GPIO37/TDO pin cannot be used for boot mode selection. In this case,
the boot ROM detects that a debug probe is connected and uses the contents of two reserved SARAM locations
in the PIE vector table to determine the boot mode. If the content of either location is invalid, then the Wait boot
option is used. All boot mode options can be accessed in emulation boot.
8.1.10.2 GetMode
The default behavior of the GetMode option is to boot to flash. This behavior can be changed to another boot
option by programming two locations in the OTP. If the content of either OTP location is invalid, then boot to flash
is used. One of the following loaders can be specified: SCI, SPI, I2C, CAN, or OTP.
Copyright © 2021 Texas Instruments Incorporated
46
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.10.3 Peripheral Pins Used by the Bootloader
Table 8-2 shows which GPIO pins are used by each peripheral bootloader. Refer to the GPIO mux table to see if
these conflict with any of the peripherals you would like to use in your application.
Table 8-2. Peripheral Bootload Pins
BOOTLOADER
PERIPHERAL LOADER PINS
SCI
SCIRXDA (GPIO28)
SCITXDA (GPIO29)
Parallel Boot
SPI
Data (GPIO31,30,5:0)
28x Control (AIO6)
Host Control (AIO12)
SPISIMOA (GPIO16)
SPISOMIA (GPIO17)
SPICLKA (GPIO18)
SPISTEA (GPIO19)
I2C
SDAA (GPIO28)
SCLA (GPIO29)
CAN
CANRXA (GPIO30)
CANTXA (GPIO31)
8.1.11 Security
The devices support high levels of security to protect the user firmware from being reverse-engineered. The
security features a 128-bit password (hardcoded for 16 wait states), which the user programs into the flash. One
code security module (CSM) is used to protect the flash/OTP and the L0/L1 SARAM blocks. The security feature
prevents unauthorized users from examining the memory contents through the JTAG port, executing code from
external memory or trying to boot-load some undesirable software that would export the secure memory
contents. To enable access to the secure blocks, the user must write the correct 128-bit KEY value that matches
the value stored in the password locations within the Flash.
In addition to the CSM, the emulation code security logic (ECSL) has been implemented to prevent unauthorized
users from stepping through secure code. Any code or data access to CSM secure memory while the debug
probe is connected will trip the ECSL and break the emulation connection. To allow emulation of secure code,
while maintaining the CSM protection against secure memory reads, the user must write the correct value into
the lower 64 bits of the KEY register, which matches the value stored in the lower 64 bits of the password
locations within the flash. Dummy reads of all 128 bits of the password in the flash must still be performed. If the
lower 64 bits of the password locations are all ones (unprogrammed), then the KEY value does not need to
match.
When initially debugging a device with the password locations in flash programmed (that is, secured), the CPU
will start running and may execute an instruction that performs an access to a protected ECSL area. If this
happens, the ECSL will trip and cause the debug probe connection to be broken.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
47
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
The solution is to use the Wait boot option. This will sit in a loop around a software breakpoint to allow a debug
probe to be connected without tripping security. These devices do not support a hardware wait-in-reset mode.
Note
•
•
When the code-security passwords are programmed, all addresses from 0x3F 7F80 to 0x3F 7FF5
cannot be used as program code or data. These locations must be programmed to 0x0000.
If the code security feature is not used, addresses 0x3F 7F80 to 0x3F 7FEF may be used for code
or data. Addresses 0x3F 7FF0 to 0x3F 7FF5 are reserved for data and should not contain program
code.
•
The 128-bit password (at 0x3F 7FF8 to 0x3F 7FFF) must not be programmed to zeros. Doing so
would permanently lock the device.
Note
Code Security Module Disclaimer
THE CODE SECURITY MODULE (CSM) INCLUDED ON THIS DEVICE WAS DESIGNED TO
PASSWORD PROTECT THE DATA STORED IN THE ASSOCIATED MEMORY (EITHER ROM OR
FLASH) AND IS WARRANTED BY TEXAS INSTRUMENTS (TI), IN ACCORDANCE WITH ITS
STANDARD TERMS AND CONDITIONS, TO CONFORM TO TI'S PUBLISHED SPECIFICATIONS
FOR THE WARRANTY PERIOD APPLICABLE FOR THIS DEVICE.
TI DOES NOT, HOWEVER, WARRANT OR REPRESENT THAT THE CSM CANNOT BE
COMPROMISED OR BREACHED OR THAT THE DATA STORED IN THE ASSOCIATED MEMORY
CANNOT BE ACCESSED THROUGH OTHER MEANS. MOREOVER, EXCEPT AS SET FORTH
ABOVE, TI MAKES NO WARRANTIES OR REPRESENTATIONS CONCERNING THE CSM OR
OPERATION OF THIS DEVICE, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL TI BE LIABLE FOR ANY CONSEQUENTIAL, SPECIAL, INDIRECT,
INCIDENTAL, OR PUNITIVE DAMAGES, HOWEVER CAUSED, ARISING IN ANY WAY OUT OF
YOUR USE OF THE CSM OR THIS DEVICE, WHETHER OR NOT TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO LOSS OF DATA, LOSS OF GOODWILL, LOSS OF USE OR INTERRUPTION OF BUSINESS OR
OTHER ECONOMIC LOSS.
8.1.12 Peripheral Interrupt Expansion (PIE) Block
The PIE block serves to multiplex numerous interrupt sources into a smaller set of interrupt inputs. The PIE block
can support up to 96 peripheral interrupts. On the F2806x, 72 of the possible 96 interrupts are used by
peripherals. The 96 interrupts are grouped into blocks of 8 and each group is fed into 1 of 12 CPU interrupt lines
(INT1 to INT12). Each of the 96 interrupts is supported by its own vector stored in a dedicated RAM block that
can be overwritten by the user. The vector is automatically fetched by the CPU on servicing the interrupt. Eight
CPU clock cycles are needed to fetch the vector and save critical CPU registers. Hence the CPU can quickly
respond to interrupt events. Prioritization of interrupts is controlled in hardware and software. Each individual
interrupt can be enabled or disabled within the PIE block.
Copyright © 2021 Texas Instruments Incorporated
48
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.13 External Interrupts (XINT1 to XINT3)
The devices support three masked external interrupts (XINT1–XINT3). Each of the interrupts can be selected for
negative, positive, or both negative and positive edge triggering and can also be enabled or disabled. These
interrupts also contain a 16-bit free-running up counter, which is reset to zero when a valid interrupt edge is
detected. This counter can be used to accurately time-stamp the interrupt. There are no dedicated pins for the
external interrupts. XINT1, XINT2, and XINT3 interrupts can accept inputs from GPIO0–GPIO31 pins.
8.1.14 Internal Zero Pin Oscillators, Oscillator, and PLL
The device can be clocked by either of the two internal zero-pin oscillators, an external oscillator, or by a crystal
attached to the on-chip oscillator circuit. A PLL is provided supporting up to 16 input-clock-scaling ratios. The
PLL ratios can be changed on-the-fly in software, enabling the user to scale back on operating frequency if lower
power operation is desired. Refer to Section 7, Specifications, for timing details. The PLL block can be set in
bypass mode. A second PLL (PLL2) feeds the HRCAP module.
8.1.15 Watchdog
Each device contains two watchdogs: CPU-watchdog that monitors the core and NMI-watchdog that is a missing
clock-detect circuit. The user software must regularly reset the CPU-watchdog counter within a certain time
frame; otherwise, the CPU-watchdog generates a reset to the processor. The CPU-watchdog can be disabled if
necessary. The NMI-watchdog engages only in case of a clock failure and can either generate an interrupt or a
device reset.
8.1.16 Peripheral Clocking
The clocks to each individual peripheral can be enabled or disabled to reduce power consumption when a
peripheral is not in use. Additionally, the system clock to the serial ports (except I2C) can be scaled relative to
the CPU clock.
8.1.17 Low-power Modes
The devices are full static CMOS devices. Three low-power modes are provided:
IDLE:
Places CPU in low-power mode. Peripheral clocks may be turned off selectively and only those peripherals that
must function during IDLE are left operating. An enabled interrupt from an active peripheral or the watchdog timer
will wake the processor from IDLE mode.
STANDBY:
HALT:
Turns off clock to CPU and peripherals. This mode leaves the oscillator and PLL functional. An external interrupt
event will wake the processor and the peripherals. Execution begins on the next valid cycle after detection of the
interrupt event
This mode basically shuts down the device and places it in the lowest possible power-consumption mode. If the
internal zero-pin oscillators are used as the clock source, the HALT mode turns them off, by default. To keep
these oscillators from shutting down, the INTOSCnHALTI bits in CLKCTL register may be used. The zero-pin
oscillators may thus be used to clock the CPU-watchdog in this mode. If the on-chip crystal oscillator is used as
the clock source, it is shut down in this mode. A reset or an external signal (through a GPIO pin) or the CPU-
watchdog can wake the device from this mode.
The CPU clock (OSCCLK) and WDCLK should be from the same clock source before attempting to put the
device into HALT or STANDBY.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
49
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.18 Peripheral Frames 0, 1, 2, 3 (PFn)
The device segregates peripherals into four sections. The mapping of peripherals is as follows:
PF0:
PIE:
PIE Interrupt Enable and Control Registers Plus PIE Vector Table
Flash Waitstate Registers
Flash:
Timers:
CSM:
ADC:
CPU-Timers 0, 1, 2 Registers
Code Security Module KEY Registers
ADC Result Registers
CLA:
Control Law Accelrator Registers and Message RAMs
GPIO MUX Configuration and Control Registers
Enhanced Control Area Network Configuration and Control Registers
System Control Registers
PF1:
PF2:
GPIO:
eCAN:
SYS:
SCI:
Serial Communications Interface (SCI) Control and RX/TX Registers
Serial Port Interface (SPI) Control and RX/TX Registers
ADC Status, Control, and Configuration Registers
Inter-Integrated Circuit Module and Registers
External Interrupt Registers
SPI:
ADC:
I2C:
XINT:
PF3:
McBSP:
ePWM:
eCAP:
eQEP:
Comparators:
USB:
Multichannel Buffered Serial Port Registers
Enhanced Pulse Width Modulator Module and Registers
Enhanced Capture Module and Registers
Enhanced Quadrature Encoder Pulse Module and Registers
Comparator Modules
Universal Serial Bus Module and Registers
8.1.19 General-Purpose Input/Output (GPIO) Multiplexer
Most of the peripheral signals are multiplexed with general-purpose input/output (GPIO) signals. This enables
the user to use a pin as GPIO if the peripheral signal or function is not used. On reset, GPIO pins are configured
as inputs. The user can individually program each pin for GPIO mode or peripheral signal mode. For specific
inputs, the user can also select the number of input qualification cycles. This is to filter unwanted noise glitches.
The GPIO signals can also be used to bring the device out of specific low-power modes.
Copyright © 2021 Texas Instruments Incorporated
50
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.20 32-Bit CPU-Timers (0, 1, 2)
CPU-Timers 0, 1, and 2 are identical 32-bit timers with presettable periods and with 16-bit clock prescaling. The
timers have a 32-bit count-down register, which generates an interrupt when the counter reaches zero. The
counter is decremented at the CPU clock speed divided by the prescale value setting. When the counter reaches
zero, it is automatically reloaded with a 32-bit period value.
CPU-Timer 0 is for general use and is connected to the PIE block. CPU-Timer 1 is also for general use and can
be connected to INT13 of the CPU. CPU-Timer 2 is reserved for SYS/BIOS. CPU-Timer 2 is connected to INT14
of the CPU. If SYS/BIOS is not being used, CPU-Timer 2 is available for general use.
CPU-Timer 2 can be clocked by any one of the following:
•
•
•
•
SYSCLKOUT (default)
Internal zero-pin oscillator 1 (INTOSC1)
Internal zero-pin oscillator 2 (INTSOC2)
External clock source
8.1.21 Control Peripherals
The devices support the following peripherals that are used for embedded control and communication:
ePWM:
The enhanced PWM peripheral supports independent/complementary PWM generation, adjustable dead-
band generation for leading/trailing edges, latched/cycle-by-cycle trip mechanism. Some of the PWM pins
support the HRPWM high-resolution duty and period features. The type 1 module found on 2806x devices
also supports increased dead-band resolution, enhanced SOC and interrupt generation, and advanced
triggering including trip functions based on comparator outputs.
eCAP:
eQEP:
The enhanced capture peripheral uses a 32-bit time base and registers up to four programmable events in
continuous/one-shot capture modes.
This peripheral can also be configured to generate an auxiliary PWM signal.
The enhanced QEP peripheral uses a 32-bit position counter, supports low-speed measurement using
capture unit and high-speed measurement using a 32-bit unit timer. This peripheral has a watchdog timer to
detect motor stall and input error detection logic to identify simultaneous edge transition in QEP signals.
ADC:
The ADC block is a 12-bit converter. The ADC has up to 16 single-ended channels pinned out, depending on
the device. The ADC also contains two sample-and-hold units for simultaneous sampling.
Comparator:
HRCAP:
Each comparator block consists of one analog comparator along with an internal 10-bit reference for
supplying one input of the comparator.
The high-resolution capture peripheral operates in normal capture mode through a 16-bit counter clocked off
of the HCCAPCLK or in high-resolution capture mode by using built-in calibration logic in conjunction with a
TI-supplied calibration library.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
51
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.1.22 Serial Port Peripherals
The devices support the following serial communication peripherals:
SPI:
The SPI is a high-speed, synchronous serial I/O port that allows a serial bit stream of programmed length (1 to
16 bits) to be shifted into and out of the device at a programmable bit-transfer rate. Normally, the SPI is used
for communications between the MCU and external peripherals or another processor. Typical applications
include external I/O or peripheral expansion through devices such as shift registers, display drivers, and
ADCs. Multidevice communications are supported by the master/slave operation of the SPI. The SPI contains
a 4-level receive and transmit FIFO for reducing interrupt servicing overhead.
SCI:
I2C:
The serial communications interface is a 2-wire asynchronous serial port, commonly known as UART. The SCI
contains a 4-level receive and transmit FIFO for reducing interrupt servicing overhead.
The inter-integrated circuit (I2C) module provides an interface between an MCU and other devices compliant
with Philips Semiconductors Inter-IC bus ( I2C-bus®) specification version 2.1 and connected by way of an
I2C-bus. External components attached to this 2-wire serial bus can transmit/receive up to 8-bit data to or from
the MCU through the I2C module. The I2C contains a 4-level receive-and-transmit FIFO for reducing interrupt
servicing overhead.
eCAN:
This is the enhanced version of the CAN peripheral. The eCAN supports 32 mailboxes, time-stamping of
messages, and is compliant with ISO 11898-1 (CAN 2.0B).
McBSP:
The multichannel buffered serial port (McBSP) connects to E1/T1 lines, phone-quality codecs for modem
applications or high-quality stereo audio DAC devices. The McBSP receive and transmit registers are
supported by the DMA to significantly reduce the overhead for servicing this peripheral. Each McBSP module
can be configured as an SPI as required.
USB:
The USB peripheral, which conforms to the USB 2.0 specification, may be used as either a full-speed (12-
Mbps) device controller, or a full-speed (12-Mbps) or low-speed (1.5-Mbps) host controller. The controller
supports a total of six user-configurable endpoints—all of which can be accessed through DMA, in addition to
a dedicated control endpoint for endpoint zero. All packets transmitted or received are buffered in 4KB of
dedicated endpoint memory. The USB peripheral supports all three transfer types: Control, Interrupt, and Bulk.
Because of the complexity of the USB peripheral and the associated protocol overhead, a full software library
with application examples is provided within C2000Ware.
Copyright © 2021 Texas Instruments Incorporated
52
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.2 Memory Maps
In Figure 8-1 through Figure 8-8, the following apply:
•
•
Memory blocks are not to scale.
Peripheral Frame 0, Peripheral Frame 1, Peripheral Frame 2, and Peripheral Frame 3 memory maps are
restricted to data memory only. A user program cannot access these memory maps in program space.
Protected means the order of Write-followed-by-Read operations is preserved rather than the pipeline order.
Certain memory ranges are EALLOW protected against spurious writes after configuration.
Locations 0x3D 7C80–0x3D 7CC0 contain the internal oscillator and ADC calibration routines. These
locations are not programmable by the user.
•
•
•
•
All devices with USB have the USB control registers mapped from 0x4000 to 0x4FFF and 2K ×16 RAM from
0x40000 to 0x40800. When the clock to the USB module is enabled, this RAM is connected to the USB
controller and acts as the FIFO RAM. When the clock to the USB module is disabled, this RAM is remapped
to the CPU-accessible address space and can be used as general-purpose RAM.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
53
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
Peripheral Frame 0
CLA Registers
0x00 1480
0x00 1500
0x00 1580
0x00 2000
0x00 4000
CLA-to-CPU Message RAM
CPU-to-CLA Message RAM
Reserved
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
0x01 0000
0x01 2000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Data RAM2)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Data RAM 0)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Data RAM 1)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Program RAM)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
L7 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 2)
L8 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 3)
0x01 4000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3D 8000
FLASH
(128K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
(B)(C)
FAST, SpinTAC, and IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
B. FAST™ and SpinTAC™ libraries exist only on F2806xM and F2806xF devices.
Copyright © 2021 Texas Instruments Incorporated
54
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
C. The ROM contents from 0x3F 8000–0x3F F3AF differ between F2806x parts and F2806xM/F2806xF parts. See the respective memory
map figures in the Boot ROM chapter of the TMS320x2806x Technical Reference Manual .
Figure 8-1. 28069, 28069F, 28069M Memory Map
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
0x00 4000
Peripheral Frame 0
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
0x01 0000
0x01 2000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
L7 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 2)
L8 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 3)
0x01 4000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3D 8000
FLASH
(128K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
(B)(C)
FAST, SpinTAC, and IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
55
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
B. FAST™ and SpinTAC™ libraries exist only on F2806xM and F2806xF devices.
C. The ROM contents from 0x3F 8000–0x3F F3AF differ between F2806x parts and F2806xM/F2806xF parts. See the respective memory
map figures in the Boot ROM chapter of the TMS320x2806x Technical Reference Manual .
Figure 8-2. 28068F, 28068M Memory Map
Copyright © 2021 Texas Instruments Incorporated
56
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
0x00 4000
Peripheral Frame 0
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
0x01 0000
0x01 2000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
L7 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 2)
L8 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 3)
0x01 4000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3D 8000
FLASH
(128K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
Figure 8-3. 28067 Memory Map
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
57
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
0x00 4000
Peripheral Frame 0
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
0x01 0000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3D 8000
FLASH
(128K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
Figure 8-4. 28066 Memory Map
Copyright © 2021 Texas Instruments Incorporated
58
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
Peripheral Frame 0
CLA Registers
0x00 1480
0x00 1500
0x00 1580
0x00 2000
0x00 4000
CLA-to-CPU Message RAM
CPU-to-CLA Message RAM
Reserved
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
0x01 0000
0x01 2000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Data RAM2)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Data RAM 0)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Data RAM 1)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL, CLA Program RAM)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
L7 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 2)
L8 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 3)
0x01 4000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3E 8000
FLASH
(64K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
Figure 8-5. 28065 Memory Map
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
59
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
0x00 4000
Peripheral Frame 0
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL)
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
0x01 0000
0x01 2000
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
L7 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 2)
L8 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 3)
0x01 4000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3E 8000
FLASH
(64K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
Figure 8-6. 28064 Memory Map
Copyright © 2021 Texas Instruments Incorporated
60
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
0x00 4000
Peripheral Frame 0
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
0x00 E000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
L6 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 1)
0x01 0000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3E 8000
FLASH
(64K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
Figure 8-7. 28063 Memory Map
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
61
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Data Space
Prog Space
0x00 0000
0x00 0040
0x00 0400
0x00 0800
0x00 0D00
M0 Vector RAM (Enabled if VMAP = 0)
M0 SARAM (1K ´ 16, 0-Wait)
M1 SARAM (1K ´ 16, 0-Wait)
Peripheral Frame 0
PIE Vector - RAM
(256 ´ 16)
(Enabled if
VMAP = 1,
ENPIE = 1)
Reserved
0x00 0E00
0x00 1400
0x00 4000
Peripheral Frame 0
Reserved
(A)
USB Control Registers
0x00 5000
Peripheral Frame 3
(4K ´ 16, Protected)
DMA-Accessible
Reserved
0x00 6000
0x00 7000
Peripheral Frame 1
(4K ´ 16, Protected)
Peripheral Frame 2
(4K ´ 16, Protected)
0x00 8000
0x00 8800
0x00 8C00
0x00 9000
0x00 A000
0x00 C000
L0 DPSARAM (2K ´ 16)
(0-Wait, Secure Zone + ECSL)
L1 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L2 DPSARAM (1K ´ 16)
(0-Wait, Secure Zone + ECSL)
L3 DPSARAM (4K ´ 16)
(0-Wait, Secure Zone + ECSL)
L4 SARAM (8K ´ 16)
(0-Wait, Secure Zone + ECSL)
L5 DPSARAM (8K ´ 16)
(0-Wait, DMA RAM 0)
0x00 E000
0x3D 7800
0x3D 7BFA
0x3D 7C80
Reserved
User OTP (1K ´ 16, Secure Zone + ECSL)
Reserved
Calibration Data
Get_mode function
Reserved
0x3D 7CC0
0x3D 7CD0
0x3D 7E80
0x3D 7E82
PARTID
Calibration Data
Reserved
0x3D 7EB0
0x3E 8000
FLASH
(64K ´ 16, 8 Sectors, Secure Zone + ECSL)
0x3F 7FF8
0x3F 8000
128-Bit Password
(B)(C)
FAST, SpinTAC, and IQmath Libraries
(16K ´ 16, 0-Wait State)
0x3F F3B0
0x3F FFC0
Boot ROM (16K ´ 16, 0-Wait State)
CPU Vector Table (32 Vectors, Enabled if VMAP = 1)
A. On non-USB devices, 0x00 4000–0x00 4FFF is Reserved.
B. FAST™ and SpinTAC™ libraries exist only on F2806xM and F2806xF devices.
C. The ROM contents from 0x3F 8000–0x3F F3AF differ between F2806x parts and F2806xM/F2806xF parts. See the respective memory
map figures in the Boot ROM chapter of the TMS320x2806x Technical Reference Manual .
Figure 8-8. 28062, 28062F Memory Map
Copyright © 2021 Texas Instruments Incorporated
62
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-3. Addresses of Flash Sectors in 28069, 28069F, 28069M,
28068F, 28068M, F28067, F28066
ADDRESS RANGE
0x3D 8000 to 0x3D BFFF
0x3D C000 to 0x3D FFFF
0x3E 0000 to 0x3E 3FFF
0x3E 4000 to 0x3E 7FFF
0x3E 8000 to 0x3E BFFF
0x3E C000 to 0x3E FFFF
0x3F 0000 to 0x3F 3FFF
0x3F 4000 to 0x3F 7FF5
PROGRAM AND DATA SPACE
Sector H (16K × 16)
Sector G (16K × 16)
Sector F (16K × 16)
Sector E (16K × 16)
Sector D (16K × 16)
Sector C (16K × 16)
Sector B (16K × 16)
Sector A (16K × 16)
Boot-to-Flash Entry Point
(program branch instruction here)
0x3F 7FF6 to 0x3F 7FF7
0x3F 7FF8 to 0x3F 7FFF
Security Password (128-Bit)
(Do not program to all zeros)
Table 8-4. Addresses of Flash Sectors in F28065, F28064, F28063, 28062,
28062F
ADDRESS RANGE
0x3E 8000 to 0x3E 9FFF
0x3E A000 to 0x3E BFFF
0x3E C000 to 0x3E DFFF
0x3E E000 to 0x3E FFFF
0x3F 0000 to 0x3F 1FFF
0x3F 2000 to 0x3F 3FFF
0x3F 4000 to 0x3F 5FFF
0x3F 6000 to 0x3F 7FF5
PROGRAM AND DATA SPACE
Sector H (8K × 16)
Sector G (8K × 16)
Sector F (8K × 16)
Sector E (8K × 16)
Sector D (8K × 16)
Sector C (8K × 16)
Sector B (8K × 16)
Sector A (8K × 16)
Boot-to-Flash Entry Point
(program branch instruction here)
0x3F 7FF6 to 0x3F 7FF7
0x3F 7FF8 to 0x3F 7FFF
Security Password (128-Bit)
(Do not program to all zeros)
Note
Addresses 0x3F 7FF0 to 0x3F 7FF5 are reserved for data and should not contain program code.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
63
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Peripheral Frame 1 and Peripheral Frame 2 are grouped together to enable these blocks to be write/read
peripheral block protected. The protected mode makes sure that all accesses to these blocks happen as written.
Because of the pipeline, a write immediately followed by a read to different memory locations, will appear in
reverse order on the memory bus of the CPU. This can cause problems in certain peripheral applications where
the user expected the write to occur first (as written). The CPU supports a block protection mode where a region
of memory can be protected so that operations occur as written (the penalty is extra cycles are added to align
the operations). This mode is programmable and by default, it protects the selected zones.
The wait states for the various spaces in the memory map area are listed in Table 8-5.
Table 8-5. Wait States
AREA
WAIT STATES (CPU)
COMMENTS
M0 and M1 SARAMs
Peripheral Frame 0
Peripheral Frame 1
0-wait
Fixed
0-wait
0-wait (writes)
2-wait (reads)
Cycles can be extended by peripheral-generated ready.
Back-to-back write operations to Peripheral Frame 1 registers will incur
a 1-cycle stall (1-cycle delay).
Peripheral Frame 2
Peripheral Frame 3
0-wait (writes)
2-wait (reads)
0-wait (writes)
Fixed. Cycles cannot be extended by the peripheral.
Assumes no conflict between CPU and CLA/DMA cycles. The wait
states can be extended by peripheral-generated ready.
2-wait (reads)
0-wait data and program
Programmable
L0–L8 SARAM
OTP
Assumes no CPU conflicts
Programmed through the Flash registers.
1-wait is minimum number of wait states allowed.
Programmed through the Flash registers.
1-wait minimum
FLASH
Programmable
0-wait Paged min
1-wait Random min
Random ≥ Paged
FLASH Password
Boot-ROM
16-wait fixed
0-wait
Wait states of password locations are fixed.
Copyright © 2021 Texas Instruments Incorporated
64
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.3 Register Maps
The devices contain four peripheral register spaces. The spaces are categorized as follows:
Peripheral Frame 0:
Peripheral Frame 1:
Peripheral Frame 2:
Peripheral Frame 3:
These are peripherals that are mapped directly to the CPU memory bus. See Table 8-6.
These are peripherals that are mapped to the 32-bit peripheral bus. See Table 8-7.
These are peripherals that are mapped to the 16-bit peripheral bus. See Table 8-8.
McBSP registers are mapped to this. See Table 8-9.
Table 8-6. Peripheral Frame 0 Registers
NAME(1)
Device Emulation registers
System Power Control registers
FLASH registers(3)
ADDRESS RANGE
0x00 0880 to 0x00 0984
0x00 0985 to 0x00 0987
0x00 0A80 to 0x00 0ADF
0x00 0AE0 to 0x00 0AEF
0x00 0B00 to 0x00 0B0F
SIZE (×16)
EALLOW PROTECTED(2)
261
3
Yes
Yes
Yes
Yes
No
96
16
16
Code Security Module registers
ADC registers (0 wait read only)
CPU-TIMER0, CPU-TIMER1, CPU-TIMER2
registers
0x00 0C00 to 0x00 0C3F
64
No
PIE registers
0x00 0CE0 to 0x00 0CFF
0x00 0D00 to 0x00 0DFF
0x00 1000 to 0x00 11FF
0x00 1400 to 0x00 147F
0x00 1480 to 0x00 14FF
0x00 1500 to 0x00 157F
32
No
Yes
Yes
Yes
NA
NA
PIE Vector Table
256
512
128
128
128
DMA registers
CLA registers
CLA to CPU Message RAM (CPU writes ignored)
CPU to CLA Message RAM (CLA writes ignored)
(1) Registers in Frame 0 support 16-bit and 32-bit accesses.
(2) If registers are EALLOW protected, then writes cannot be performed until the EALLOW instruction is executed. The EDIS instruction
disables writes to prevent stray code or pointers from corrupting register contents.
(3) The Flash Registers are also protected by the Code Security Module (CSM).
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
65
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-7. Peripheral Frame 1 Registers
NAME
ADDRESS RANGE
0x00 6000 to 0x00 61FF
0x00 6AC0 to 0x00 6ADF
0x00 6AE0 to 0x00 6AFF
0x00 6C80 to 0x00 6C9F
0x00 6CA0 to 0x00 6CBF
0x00 6F80 to 0x00 6FFF
SIZE (×16)
EALLOW PROTECTED
(1)
(1)
(1)
(1)
(1)
(1)
eCAN-A registers
HRCAP1 registers
HRCAP2 registers
HRCAP3 registers
HRCAP4 registers
GPIO registers
512
32
32
32
32
128
(1) Some registers are EALLOW protected. See the module reference guide for more information.
Table 8-8. Peripheral Frame 2 Registers
NAME
System Control registers
ADDRESS RANGE
0x00 7010 to 0x00 702F
0x00 7040 to 0x00 704F
0x00 7050 to 0x00 705F
0x00 7060 to 0x00 706F
0x00 7070 to 0x00 707F
0x00 7100 to 0x00 717F
0x00 7740 to 0x00 774F
0x00 7750 to 0x00 775F
0x00 7900 to 0x00 793F
SIZE (×16)
EALLOW PROTECTED
32
16
16
16
16
128
16
16
64
Yes
No
SPI-A registers
SCI-A registers
No
NMI Watchdog Interrupt registers
External Interrupt registers
ADC registers
Yes
Yes
(1)
SPI-B registers
No
SCI-B registers
No
(1)
I2C-A registers
(1) Some registers are EALLOW protected. See the module reference guide for more information.
Table 8-9. Peripheral Frame 3 Registers
NAME
ADDRESS RANGE
0x00 4000 to 0x00 4FFF
0x00 5000 to 0x00 503F
0x00 6400 to 0x00 641F
0x00 6420 to 0x00 643F
0x00 6440 to 0x00 645F
0x00 6800 to 0x00 683F
0x00 6840 to 0x00 687F
0x00 6880 to 0x00 68BF
0x00 68C0 to 0x00 68FF
0x00 6900 to 0x00 693F
0x00 6940 to 0x00 697F
0x00 6980 to 0x00 69BF
0x00 69C0 to 0x00 69FF
0x00 6A00 to 0x00 6A1F
0x00 6A20 to 0x00 6A3F
0x00 6A40 to 0x00 6A57
0x00 6B00 to 0x00 6B3F
0x00 6B40 to 0x00 6B7F
SIZE (×16)
4096
64
EALLOW PROTECTED
USB0 registers
No
McBSP-A registers
No
(1)
Comparator 1 registers
Comparator 2 registers
Comparator 3 registers
ePWM1 + HRPWM1 registers
ePWM2 + HRPWM2 registers
ePWM3 + HRPWM3 registers
ePWM4 + HRPWM4 registers
ePWM5 + HRPWM5 registers
ePWM6 + HRPWM6 registers
ePWM7 + HRPWM7 registers
ePWM8 + HRPWM8 registers
eCAP1 registers
32
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
32
32
64
64
64
64
64
64
64
64
32
No
No
eCAP2 registers
32
eCAP3 registers
32
No
(1)
eQEP1 registers
64
(1)
eQEP2 registers
64
(1) Some registers are EALLOW protected. See the module reference guide for more information.
Copyright © 2021 Texas Instruments Incorporated
66
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.4 Device Emulation Registers
These registers are used to control the protection mode of the C28x CPU and to monitor some critical device
signals. The registers are defined in Table 8-10.
Table 8-10. Device Emulation Registers
EALLOW
PROTECTED
NAME
ADDRESS RANGE
SIZE (×16)
DESCRIPTION
Device Configuration Register
Part ID Register
0x0880–
0x0881
DEVICECNF
PARTID
2
1
Yes
0x3D 7E80
TMS320F28069PZP/PZ
TMS320F28069UPZP/PZ
TMS320F28069MPZP/PZ
TMS320F28069FPZP/PZ
TMS320F28069PFP/PN
TMS320F28069UPFP/PN
TMS320F28069MPFP/PN
TMS320F28069FPFP/PN
TMS320F28068UPZP/PZ
TMS320F28068MPZP/PZ
TMS320F28068FPZP/PZ
TMS320F28068UPFP/PN
TMS320F28068MPFP/PN
TMS320F28068FPFP/PN
TMS320F28067PZP/PZ
TMS320F28067UPZP/PZ
TMS320F28067PFP/PN
TMS320F28067UPFP/PN
TMS320F28066PZP/PZ
TMS320F28066UPZP/PZ
TMS320F28066PFP/PN
TMS320F28066UPFP/PN
TMS320F28065PZP/PZ
TMS320F28065UPZP/PZ
TMS320F28065PFP/PN
TMS320F28065UPFP/PN
TMS320F28064PZP/PZ
TMS320F28064UPZP/PZ
TMS320F28064PFP/PN
TMS320F28064UPFP/PN
TMS320F28063PZP/PZ
TMS320F28063UPZP/PZ
TMS320F28063PFP/PN
TMS320F28063UPFP/PN
TMS320F28062PZP/PZ
TMS320F28062UPZP/PZ
TMS320F28062FPZP/PZ
TMS320F28062PFP/PN
TMS320F28062UPFP/PN
TMS320F28062FPFP/PN
0x009E
0x009F
0x009E
0x009E
0x009C
0x009D
0x009C
0x009C
0x008F
0x008E
0x008E
0x008D
0x008C
0x008C
0x008A
0x008B
0x0088
0x0089
0x0086
0x0087
0x0084
0x0085
0x007E
0x007F
0x007C
0x007D
0x006E
0x006F
0x006C
0x006D
0x006A
0x006B
0x0068
0x0069
0x0066
0x0067
0x0066
0x0064
0x0065
0x0064
No
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
67
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-10. Device Emulation Registers (continued)
EALLOW
PROTECTED
NAME
CLASSID
ADDRESS RANGE
SIZE (×16)
DESCRIPTION
0x0882
1
Class ID Register
TMS320F28069
0x009F
0x009F
0x009F
0x009F
0x008F
0x008F
0x008F
0x008F
0x008F
0x008F
0x008F
0x007F
0x007F
0x006F
0x006F
0x006F
0x006F
0x006F
0x006F
0x006F
TMS320F28069U
TMS320F28069M
TMS320F28069F
TMS320F28068U
TMS320F28068M
TMS320F28068F
TMS320F28067
TMS320F28067U
TMS320F28066
No
TMS320F28066U
TMS320F28065
TMS320F28065U
TMS320F28064
TMS320F28064U
TMS320F28063
TMS320F28063U
TMS320F28062
TMS320F28062U
TMS320F28062F
0x0000 - Silicon Rev. 0 - TMX
0x0001 - Silicon Rev. A - TMS
0x0002 - Silicon Rev. B - TMS
REVID
0x0883
1
Revision ID Register
No
Copyright © 2021 Texas Instruments Incorporated
68
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.5 VREG, BOR, POR
Although the core and I/O circuitry operate on two different voltages, these devices have an on-chip VREG to
generate the VDD voltage from the VDDIO supply. This eliminates the cost and space of a second external
regulator on an application board. Additionally, internal power-on reset (POR) and brownout reset (BOR) circuits
monitor both the VDD and VDDIO rails during power-up and run mode.
8.5.1 On-chip VREG
A linear regulator generates the core voltage (VDD) from the VDDIO supply. Therefore, although capacitors are
required on each VDD pin to stabilize the generated voltage, power need not be supplied to these pins to operate
the device. Conversely, the VREG can be disabled, should power or redundancy be the primary concern of the
application.
8.5.1.1 Using the On-chip VREG
To use the on-chip VREG, the VREGENZ pin should be tied low and the appropriate recommended operating
voltage should be supplied to the VDDIO and VDDA pins. In this case, the VDD voltage needed by the core logic
will be generated by the VREG. Each VDD pin requires on the order of 1.2 μF (minimum) capacitance for proper
regulation of the VREG. These capacitors should be located as close as possible to the VDD pins. Driving an
external load with the internal VREG is not supported.
8.5.1.2 Disabling the On-chip VREG
To conserve power, it is also possible to disable the on-chip VREG and supply the core logic voltage to the VDD
pins with a more efficient external regulator. To enable this option, the VREGENZ pin must be tied high.
8.5.2 On-chip Power-On Reset (POR) and Brownout Reset (BOR) Circuit
Two on-chip supervisory circuits, the power-on reset (POR) and the brownout reset (BOR) remove the burden of
monitoring the VDD and VDDIO supply rails from the application board. The purpose of the POR is to create a
clean reset throughout the device during the entire power-up procedure. The trip point is a looser, lower trip point
than the BOR, which watches for dips in the VDD or VDDIO rail during device operation. The POR function is
present on both VDD and VDDIO rails at all times. After initial device power-up, the BOR function is present on
VDDIO at all times, and on VDD when the internal VREG is enabled ( VREGENZ pin is tied low). Both functions tie
the XRS pin low when one of the voltages is below their respective trip point. VDD BOR and overvoltage trip
points are outside of the recommended operating voltages. Proper device operation cannot be ensured. If
overvoltage or undervoltage conditions affecting the system is a concern for an application, an external voltage
supervisor should be added. Figure 8-9 shows the VREG, POR, and BOR. To disable both the VDD and VDDIO
BOR functions, a bit is provided in the BORCFG register. For details, see the Systems Control and Interrupts
chapter of the TMS320x2806x Technical Reference Manual .
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
69
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
In
I/O Pin
Out
(Force Hi-Z When High)
DIR (0 = Input, 1 = Output)
SYSRS
Internal
Weak PU
SYSCLKOUT
Sync
Deglitch
Filter
RS
WDRST
C28
Core
MCLKRS
JTAG
TCK
PLL
Detect
Logic
XRS
Pin
+
Clocking
Logic
VREGHALT
WDRST(A)
PBRS(B)
POR/BOR
On-Chip
Generating
Voltage
VREGENZ
Module
Regulator
(VREG)
A. WDRST is the reset signal from the CPU-watchdog.
B. PBRS is the reset signal from the POR/BOR module.
Figure 8-9. VREG + POR + BOR + Reset Signal Connectivity
Copyright © 2021 Texas Instruments Incorporated
70
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.6 System Control
This section describes the oscillator and clocking mechanisms, the watchdog function and the low-power modes.
Table 8-11. PLL, Clocking, Watchdog, and Low-Power Mode Registers
NAME
ADDRESS
0x00 0985
0x00 7010
0x00 7011
0x00 7012
0x00 7013
0x00 7014
0x00 7016
0x00 7019
0x00 701B
0x00 701C
0x00 701D
0x00 701E
0x00 7020
0x00 7021
0x00 7022
0x00 7023
0x00 7025
0x00 7029
0x00 702A
0x00 7030
0x00 7032
0x00 7034
0x00 7036
0x00 703A
SIZE (×16)
DESCRIPTION(1)
BORCFG
XCLK
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
BOR Configuration Register
XCLKOUT Control
PLLSTS
CLKCTL
PLL Status Register
Clock Control Register
PLLLOCKPRD
INTOSC1TRIM
INTOSC2TRIM
PCLKCR2
LOSPCP
PLL Lock Period
Internal Oscillator 1 Trim Register
Internal Oscillator 2 Trim Register
Peripheral Clock Control Register 2
Low-Speed Peripheral Clock Prescaler Register
Peripheral Clock Control Register 0
Peripheral Clock Control Register 1
Low-Power Mode Control Register 0
Peripheral Clock Control Register 3
PLL Control Register
PCLKCR0
PCLKCR1
LPMCR0
PCLKCR3
PLLCR
SCSR
System Control and Status Register
Watchdog Counter Register
Watchdog Reset Key Register
Watchdog Control Register
WDCNTR
WDKEY
WDCR
JTAGDEBUG
PLL2CTL
JTAG Port Debug Register
PLL2 Configuration Register
PLL2 Multiplier Register
PLL2MULT
PLL2STS
PLL2 Lock Status Register
SYSCLK2CNTR
EPWMCFG
SYSCLK2 Clock Counter Register
ePWM DMA/CLA Configuration Register
(1) All registers in this table are EALLOW protected.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
71
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Figure 8-10 shows the various clock domains that are discussed. Figure 8-11 shows the various clock sources
(both internal and external) that can provide a clock for device operation.
SYSCLKOUT
PCLKCR0/1/2/3
(System Ctrl Regs)
LOSPCP
(System Ctrl Regs)
PLL2
C28x Core
CLKIN
LSPCLK
Clock Enables
SPI-A, SPI-B, SCI-A, SCI-B
Clock Enables
USB
Peripheral
Registers
I/O
I/O
PF2
Peripheral
Registers
PF3
LOSPCP
(System Ctrl Regs)
Clock Enables
LSPCLK
Peripheral
Registers
I/O
I/O
I/O
I/O
McBSP
Clock Enables
eCAN-A
PF3
PF1
PF3
PF3
PF2
PF1
/2
Peripheral
Registers
GPIO
Mux
Clock Enables
Peripheral
Registers
eCAP1, eCAP2, eCAP3
eQEP1, eQEP2
Clock Enables
ePWM1, ePWM2,
ePWM3, ePWM4, ePWM5,
ePWM6, ePWM7, ePWM8
Peripheral
Registers
Clock Enables
Peripheral
Registers
I2C-A
I/O
I/O
Clock Enables
Peripheral
Registers
HRCAP1, HRCAP2,
HRCAP3, HRCAP4
Clock Enables
12-Bit ADC
ADC
Registers
PF2
PF0
16 Ch
Analog
GPIO
Mux
Clock Enables
COMP
Registers
COMP1, COMP2, COMP3
6
PF3
A. CLKIN is the clock into the CPU. CLKIN is passed out of the CPU as SYSCLKOUT (that is, CLKIN is the same frequency as
SYSCLKOUT).
Figure 8-10. Clock and Reset Domains
Copyright © 2021 Texas Instruments Incorporated
72
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
CLKCTL[WDCLKSRCSEL]
Internal
OSC 1
(10 MHz)
0
OSC1CLK
INTOSC1TRIM Reg(A)
OSCCLKSRC1
WDCLK
CPU-Watchdog
(OSC1CLK on XRS reset)
OSCE
1
CLKCTL[INTOSC1OFF]
1 = Turn OSC Off
CLKCTL[OSCCLKSRCSEL]
CLKCTL[INTOSC1HALT]
1 = Ignore HALT
WAKEOSC
OSC2CLK
0
1
Internal
OSC 2
(10 MHz)
INTOSC2TRIM Reg(A)
OSCCLK
PLL
Missing-Clock-Detect Circuit(B)
SYSCLKOUT
(OSC1CLK on XRS reset)
OSCE
CLKCTL[TRM2CLKPRESCALE]
CLKCTL[TMR2CLKSRCSEL]
1 = Turn OSC Off
10
11
CLKCTL[INTOSC2OFF]
Prescale
/1, /2, /4,
/8, /16
SYNC
Edge
Detect
01, 10, 11
CPUTMR2CLK
1 = Ignore HALT
01
1
0
00
CLKCTL[INTOSC2HALT]
SYSCLKOUT
OSCCLKSRC2
CLKCTL[OSCCLKSRC2SEL]
0 = GPIO38
1 = GPIO19
XCLK[XCLKINSEL]
PLL2CTL.PLL2CLKSRCSEL
PLL2CTL.PLL2EN
CLKCTL[XCLKINOFF]
0
1
0
DEVICECNF[SYSCLK2DIV2DIS]
PLL2
GPIO19
or
XCLKIN
0
/2
GPIO38
XCLKIN
SYSCLK2 to USB
HRCAP
1
X1
X2
PLL2CLK
EXTCLK
(Crystal)
OSC
XTAL
WAKEOSC
(Oscillators enabled when this signal is high)
0 = OSC on (default on reset)
1 = Turn OSC off
CLKCTL[XTALOSCOFF]
A. Register loaded from TI OTP-based calibration function.
B. See Section 8.6.5 for details on missing clock detection.
Figure 8-11. Clock Tree
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
73
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.6.1 Internal Zero Pin Oscillators
The F2806x devices contain two independent internal zero pin oscillators. By default both oscillators are turned
on at power up, and internal oscillator 1 is the default clock source at this time. For power savings, unused
oscillators may be powered down by the user. The center frequency of these oscillators is determined by their
respective oscillator trim registers, written to in the calibration routine as part of the boot ROM execution. See
Section 8.9 for more information on these oscillators.
8.6.2 Crystal Oscillator Option
The on-chip crystal oscillator X1 and X2 pins are 1.8-V level signals and must never have 3.3-V level signals
applied to them. If a system 3.3-V external oscillator is to be used as a clock source, it should be connected to
the XCLKIN pin only. The X1 pin is not intended to be used as a single-ended clock input, it should be used with
X2 and a crystal.
The typical specifications for the external quartz crystal (fundamental mode, parallel resonant) are listed in Table
8-12. Furthermore, ESR range = 30 to 150 Ω.
Table 8-12. Typical Specifications for External Quartz Crystal (1)
FREQUENCY (MHz)
Rd (Ω)
2200
470
0
CL1 (pF)
CL2 (pF)
5
18
18
10
15
20
15
15
15
15
0
12
12
(1) Cshunt should be less than or equal to 5 pF.
XCLKIN/GPIO19/38
X1
X2
Rd
Turn off
XCLKIN path
in CLKCTL
register
Crystal
CL1
CL2
Figure 8-12. Using the On-chip Crystal Oscillator
Note
1. CL1 and CL2 are the total capacitance of the circuit board and components excluding the IC and
crystal. The value is usually approximately twice the value of the load capacitance of the crystal.
2. The load capacitance of the crystal is described in the crystal specifications of the manufacturers.
3. TI recommends that customers have the resonator/crystal vendor characterize the operation of
their device with the MCU chip. The resonator/crystal vendor has the equipment and expertise to
tune the tank circuit. The vendor can also advise the customer regarding the proper tank
component values that will produce proper start-up and stability over the entire operating range.
XCLKIN/GPIO19/38
X1
X2
NC
External Clock Signal
(Toggling 0−V
)
DDIO
Figure 8-13. Using a 3.3-V External Oscillator
Copyright © 2021 Texas Instruments Incorporated
74
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.6.3 PLL-Based Clock Module
The devices have an on-chip, PLL-based clock module. This module provides all the necessary clocking signals
for the device, as well as control for low-power mode entry. The PLL has a 5-bit ratio control PLLCR[DIV] to
select different CPU clock rates. The watchdog module should be disabled before writing to the PLLCR register.
The watchdog module can be re-enabled (if need be) after the PLL module has stabilized, which takes 1 ms.
The input clock and PLLCR[DIV] bits should be chosen in such a way that the output frequency of the PLL
(VCOCLK) is at least 50 MHz.
Table 8-13. PLL Settings
SYSCLKOUT (CLKIN)
PLLCR[DIV] VALUE(2) (3)
PLLSTS[DIVSEL] = 0 or 1(1)
OSCCLK/4 (Default)(2)
(OSCCLK * 1)/4
(OSCCLK * 2)/4
(OSCCLK * 3)/4
(OSCCLK * 4)/4
(OSCCLK * 5)/4
(OSCCLK * 6)/4
(OSCCLK * 7)/4
(OSCCLK * 8)/4
(OSCCLK * 9)/4
(OSCCLK * 10)/4
(OSCCLK * 11)/4
(OSCCLK * 12)/4
(OSCCLK * 13)/4
(OSCCLK * 14)/4
(OSCCLK * 15)/4
(OSCCLK * 16)/4
(OSCCLK * 17)/4
(OSCCLK * 18)/4
PLLSTS[DIVSEL] = 2
OSCCLK/2
PLLSTS[DIVSEL] = 3
OSCCLK
00000 (PLL bypass)
00001
00010
00011
(OSCCLK * 1)/2
(OSCCLK * 2)/2
(OSCCLK * 3)/2
(OSCCLK * 4)/2
(OSCCLK * 5)/2
(OSCCLK * 6)/2
(OSCCLK * 7)/2
(OSCCLK * 8)/2
(OSCCLK * 9)/2
(OSCCLK * 10)/2
(OSCCLK * 11)/2
(OSCCLK * 12)/2
(OSCCLK * 13)/2
(OSCCLK * 14)/2
(OSCCLK * 15)/2
(OSCCLK * 16)/2
(OSCCLK * 17)/2
(OSCCLK * 18)/2
(OSCCLK * 1)/1
(OSCCLK * 2)/1
(OSCCLK * 3)/1
(OSCCLK * 4)/1
(OSCCLK * 5)/1
(OSCCLK * 6)/1
(OSCCLK * 7)/1
(OSCCLK * 8)/1
(OSCCLK * 9)/1
(OSCCLK * 10)/1
(OSCCLK * 11)/1
(OSCCLK * 12)/1
(OSCCLK * 13)/1
(OSCCLK * 14)/1
(OSCCLK * 15)/1
(OSCCLK * 16)/1
(OSCCLK * 17)/1
(OSCCLK * 18)/1
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
(1) By default, PLLSTS[DIVSEL] is configured for /4. (The boot ROM changes this to /1.) PLLSTS[DIVSEL] must be 0 before writing to the
PLLCR and should be changed only after PLLSTS[PLLLOCKS] = 1.
(2) The PLL control register (PLLCR) and PLL Status Register (PLLSTS) are reset to their default state by the XRS signal or a watchdog
reset only. A reset issued by the debugger or the missing clock detect logic has no effect.
(3) This register is EALLOW protected. See the Systems Control and Interrupts chapter of the TMS320x2806x Technical Reference
Manual for more information.
Table 8-14. CLKIN Divide Options
PLLSTS [DIVSEL]
CLKIN DIVIDE
0
1
2
3
/4
/4
/2
/1
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
75
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
The PLL-based clock module provides four modes of operation:
•
INTOSC1 (Internal Zero-pin Oscillator 1): This is the on-chip internal oscillator 1. This can provide the clock
for the Watchdog block, core and CPU-Timer 2
•
INTOSC2 (Internal Zero-pin Oscillator 2): This is the on-chip internal oscillator 2. This can provide the clock
for the Watchdog block, core and CPU-Timer 2. Both INTOSC1 and INTOSC2 can be independently chosen
for the Watchdog block, core and CPU-Timer 2.
•
•
Crystal/Resonator Operation: The on-chip (crystal) oscillator enables the use of an external crystal/
resonator attached to the device to provide the time base. The crystal/resonator is connected to the X1/X2
pins. Some devices may not have the X1/X2 pins. See Section 6.2.1 for details.
External Clock Source Operation: If the on-chip (crystal) oscillator is not used, this mode allows it to be
bypassed. The device clocks are generated from an external clock source input on the XCLKIN pin. The
XCLKIN is multiplexed with GPIO19 or GPIO38 pin. The XCLKIN input can be selected as GPIO19 or
GPIO38 through the XCLKINSEL bit in XCLK register. The CLKCTL[XCLKINOFF] bit disables this clock input
(forced low). If the clock source is not used or the respective pins are used as GPIOs, the user should disable
at boot time.
Before changing clock sources, ensure that the target clock is present. If a clock is not present, then that clock
source must be disabled (using the CLKCTL register) before switching clocks.
Table 8-15. Possible PLL Configuration Modes
PLL MODE
REMARKS
PLLSTS[DIVSEL] CLKIN AND SYSCLKOUT
PLL Off
Invoked by the user setting the PLLOFF bit in the PLLSTS register. The
PLL block is disabled in this mode. This can be useful to reduce system
noise and for low-power operation. The PLLCR register must first be set
to 0x0000 (PLL Bypass) before entering this mode. The CPU clock
(CLKIN) is derived directly from the input clock on either X1/X2, X1 or
XCLKIN.
0, 1
2
OSCCLK/4
OSCCLK/2
OSCCLK/1
3
PLL Bypass PLL Bypass is the default PLL configuration upon power-up or after an
external reset ( XRS). This mode is selected when the PLLCR register is
set to 0x0000 or while the PLL locks to a new frequency after the PLLCR
register has been modified. In this mode, the PLL is bypassed but the
PLL is not turned off.
0, 1
2
OSCCLK/4
OSCCLK/2
OSCCLK/1
3
PLL Enable Achieved by writing a non-zero value n into the PLLCR register. Upon
writing to the PLLCR the device will switch to PLL Bypass mode until the
PLL locks.
0, 1
2
OSCCLK * n/4
OSCCLK * n/2
OSCCLK * n/1
3
Copyright © 2021 Texas Instruments Incorporated
76
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.6.4 USB and HRCAP PLL Module (PLL2)
In addition to the main system PLL, these devices also contain a second PLL (PLL2) which can be used to clock
the USB and HRCAP peripherals. The PLL supports multipliers of 1 to 15 and has a fixed divide-by-two on its
output.
PLL2 may be clocked from the following three sources by modifying the PLL2CLKSRCSEL bits appropriately in
the PLL2CTL register:
•
INTOSC1 (Internal Zero-pin Oscillator 1): This is the on-chip internal oscillator 1 and provides a 10-MHz
clock. If used as a clock source for HRCAP, the oscillator compensation routine should be called frequently.
Because of accuracy requirements, INTOSC1 cannot be used as a clock source for the USB.
Crystal/Resonator Operation: The (crystal) oscillator enables the use of an external crystal or resonator
attached to the device to provide the time base. The crystal or resonator is connected to the X1/X2 pins.
External Clock Source Operation: This mode allows the reference clock to be derived from an external single-
ended clock source connected to either GPIO19 or GPIO38. The XCLKINSEL bit in the XCLK register should
be set appropriately to enable the selected GPIO to drive XCLKIN.
•
•
Note
For proper operation of the USB module, PLL2 should be configured to generate a 120-MHz clock.
This will be divided by two to yield the desired 60 MHz for the USB peripheral.
HRCAP supports a maximum clock input frequency of 120 MHz.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
77
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.6.5 Loss of Input Clock (NMI Watchdog Function)
The 2806x devices may be clocked from either one of the internal zero-pin oscillators (INTOSC1/INTOSC2), the
on-chip crystal oscillator, or from an external clock input. Regardless of the clock source, in PLL-enabled and
PLL-bypass mode, if the input clock to the PLL vanishes, the PLL will issue a limp-mode clock at its output. This
limp-mode clock continues to clock the CPU and peripherals at a typical frequency of 1–5 MHz.
When the limp mode is activated, a CLOCKFAIL signal is generated that is latched as an NMI interrupt.
Depending on how the NMIRESETSEL bit has been configured, a reset to the device can be fired immediately or
the NMI watchdog counter can issue a reset when it overflows. In addition to this, the Missing Clock Status
(MCLKSTS) bit is set. The NMI interrupt could be used by the application to detect the input clock failure and
initiate necessary corrective action such as switching over to an alternative clock source (if available) or initiate a
shut-down procedure for the system.
If the software does not respond to the clock-fail condition, the NMI watchdog triggers a reset after a
preprogrammed time interval. Figure 8-14 shows the interrupt mechanisms involved.
NMIFLG[NMINT]
NMIFLGCLR[NMINT]
Clear
Latch
Set
Clear
XRS
Generate
Interrupt
Pulse
When
Input = 1
NMIFLG[CLOCKFAIL]
Clear
Latch
1
0
0
NMIFLGCLR[CLOCKFAIL]
CLOCKFAIL
NMINT
SYNC?
Set
Clear
SYSCLKOUT
NMICFG[CLOCKFAIL]
NMIFLGFRC[CLOCKFAIL]
XRS
SYSCLKOUT
SYSRS
NMIWDPRD[15:0]
NMIWDCNT[15:0]
See System
Control Section
NMI Watchdog
NMIRS
Figure 8-14. NMI-Watchdog
8.6.6 CPU Watchdog Module
The CPU watchdog module on the 2806x device is similar to the one used on the 281x/280x/283xx devices. This
module generates an output pulse, 512 oscillator clocks wide (OSCCLK), whenever the 8-bit watchdog up
counter has reached its maximum value. To prevent this, the user must disable the counter or the software must
periodically write a 0x55 + 0xAA sequence into the watchdog key register that resets the watchdog counter.
Figure 8-15 shows the various functional blocks within the watchdog module.
Copyright © 2021 Texas Instruments Incorporated
78
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Normally, when the input clocks are present, the CPU-watchdog counter decrements to initiate a CPU-watchdog
reset or WDINT interrupt. However, when the external input clock fails, the CPU-watchdog counter stops
decrementing (that is, the watchdog counter does not change with the limp-mode clock).
Note
The CPU-watchdog is different from the NMI watchdog. The CPU-watchdog is the legacy watchdog
that is present in all 28x devices.
Note
Applications in which the correct CPU operating frequency is absolutely critical should implement a
mechanism by which the MCU will be held in reset, should the input clocks ever fail. For example, an
R-C circuit may be used to trigger the XRS pin of the MCU, should the capacitor ever get fully
charged. An I/O pin may be used to discharge the capacitor on a periodic basis to prevent it from
getting fully charged. Such a circuit would also help in detecting failure of the flash memory.
WDCR (WDPS[2:0])
WDCR (WDDIS)
WDCNTR(7:0)
WDCLK
WDCLK
8-Bit
Watchdog
Counter
CLR
Watchdog
Prescaler
/512
SCSR(WDOVERRIDE)
Clear Counter
Internal
Pullup
WDKEY(7:0)
WDRST
WDINT
Generate
Watchdog
55 + AA
Output Pulse
(512 OSCCLKs)
Good Key
Key Detector
XRS
Bad
WDCHK
Key
Core-reset
SCSR (WDENINT)
WDCR (WDCHK[2:0])
1
0
1
(A)
WDRST
A. The WDRST signal is driven low for 512 OSCCLK cycles.
Figure 8-15. CPU Watchdog Module
The WDINT signal enables the watchdog to be used as a wakeup from IDLE/STANDBY mode.
In STANDBY mode, all peripherals are turned off on the device. The only peripheral that remains functional is
the CPU-watchdog. This module will run off OSCCLK. The WDINT signal is fed to the LPM block so that it can
wake the device from STANDBY (if enabled). See Section 8.7 for more details.
In IDLE mode, the WDINT signal can generate an interrupt to the CPU, through the PIE, to take the CPU out of
IDLE mode.
In HALT mode, the CPU-watchdog can be used to wake up the device through a device reset.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
79
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.7 Low-power Modes Block
Table 8-16 summarizes the various modes.
Table 8-16. Low-power Modes
MODE
LPMCR0(1:0)
OSCCLK
CLKIN
SYSCLKOUT
EXIT(1)
XRS, CPU-watchdog interrupt, any
enabled interrupt
IDLE
00
On
On
On
On
XRS, CPU-watchdog interrupt, GPIO
Port A signal, debugger(2)
STANDBY
HALT(3)
01
1X
Off
Off
Off
Off
(CPU-watchdog still running)
Off
(on-chip crystal oscillator and PLL
turned off, zero-pin oscillator and
CPU-watchdog state dependent
on user code.)
XRS, GPIO Port A signal, debugger(2)
CPU-watchdog
,
(1) The EXIT column lists which signals or under what conditions the low-power mode is exited. A low signal, on any of the signals, exits
the low-power condition. This signal must be kept low long enough for an interrupt to be recognized by the device. Otherwise, the low-
power mode will not be exited and the device will go back into the indicated low-power mode.
(2) The JTAG port can still function even if the CPU clock (CLKIN) is turned off.
(3) The WDCLK must be active for the device to go into HALT mode.
The various low-power modes operate as follows:
IDLE Mode:
This mode is exited by any enabled interrupt that is recognized by the processor. The LPM block
performs no tasks during this mode as long as the LPMCR0(LPM) bits are set to 0,0.
STANDBY Mode:
Any GPIO port A signal (GPIO[31:0]) can wake the device from STANDBY mode. The user must
select which signals will wake the device in the GPIOLPMSEL register. The selected signals are also
qualified by the OSCCLK before waking the device. The number of OSCCLKs is specified in the
LPMCR0 register.
HALT Mode:
CPU-watchdog, XRS, and any GPIO port A signal (GPIO[31:0]) can wake the device from HALT
mode. The user selects the signal in the GPIOLPMSEL register.
Note
The low-power modes do not affect the state of the output pins (PWM pins included). They will be in
whatever state the code left them in when the IDLE instruction was executed. See the Systems
Control and Interrupts chapter of the TMS320x2806x Technical Reference Manual for more details.
Copyright © 2021 Texas Instruments Incorporated
80
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.8 Interrupts
Figure 8-16 shows how the various interrupt sources are multiplexed.
Peripherals
(SPI, SCI, I2C, eCAN, eCAP, eQEP,
HRCAP, CLA)
Peripherals
(USB, McBSP, ePWM, ADC)
clear
DMA
C28x
Core
WDINT
Watchdog
WAKEINT
Sync
LPMINT
Low-Power Modes
SYSCLKOUT
DMA
M
U
X
XINT1
XINT1
Interrupt Control
XINT1CR[15:0]
XINT1CTR[15:0]
INT1
to
INT12
GPIOXINT1SEL[4:0]
XINT2SOC
DMA
ADC
M
U
X
XINT2
XINT2
Interrupt Control
XINT2CR[15:0]
XINT2CTR[15:0]
GPIOXINT2SEL[4:0]
GPIO0.int
DMA
DMA
M
XINT3
XINT3
U
GPIO
MUX
Interrupt Control
XINT3CR[15:0]
XINT3CTR[15:0]
X
GPIO31.int
GPIOXINT3SEL[4:0]
TINT0
TINT1
TINT2
CPU TIMER 0
CPU TIMER 1
CPU TIMER 2
TOUT1
Flash Wrapper
INT13
INT14
CPUTMR2CLK
CLOCKFAIL
NMIRS
NMI Interrupt With Watchdog Function
(See the NMI Watchdog section.)
System Control
(See the System Control section.)
NMI
Figure 8-16. External and PIE Interrupt Sources
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
81
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Eight PIE block interrupts are grouped into one CPU interrupt. In total, 12 CPU interrupt groups, with 8 interrupts
per group equals 96 possible interrupts. Table 8-17 shows the interrupts used by 2806x devices.
The TRAP #VectorNumber instruction transfers program control to the interrupt service routine (ISR)
corresponding to the vector specified. The TRAP #0 instruction attempts to transfer program control to the
address pointed to by the reset vector. The PIE vector table does not, however, include a reset vector. Therefore,
the TRAP #0 instruction should not be used when the PIE is enabled. Doing so will result in undefined behavior.
When the PIE is enabled, the TRAP #1 to TRAP #12 instructions will transfer program control to the ISR
corresponding to the first vector within the PIE group. For example: the TRAP #1 instruction fetches the vector
from INT1.1, the TRAP #2 instruction fetches the vector from INT2.1, and so forth.
IFR[12:1]
IER[12:1]
INTM
INT1
INT2
1
CPU
MUX
0
INT11
INT12
Global
Enable
(Flag)
(Enable)
INTx.1
INTx.2
INTx.3
INTx.4
INTx.5
From
Peripherals
or
External
Interrupts
INTx
MUX
INTx.6
INTx.7
INTx.8
PIEACKx
(Enable)
(Flag)
(Enable/Flag)
PIEIERx[8:1]
PIEIFRx[8:1]
Figure 8-17. Multiplexing of Interrupts Using the PIE Block
Copyright © 2021 Texas Instruments Incorporated
82
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-17. PIE MUXed Peripheral Interrupt Vector Table (1)
INTx.8
WAKEINT
(LPM/WD)
0xD4E
INTx.7
INTx.6
ADCINT9
(ADC)
INTx.5
INTx.4
INTx.3
Reserved
–
INTx.2
ADCINT2
(ADC)
INTx.1
ADCINT1
(ADC)
INT1.y
INT2.y
INT3.y
INT4.y
INT5.y
INT6.y
INT7.y
INT8.y
INT9.y
INT10.y
INT11.y
INT12.y
TINT0
XINT2
XINT1
(TIMER 0)
0xD4C
Ext. int. 2
0xD48
Ext. int. 1
0xD46
0xD4A
0xD44
0xD42
0xD40
EPWM8_TZINT
(ePWM8)
0xD5E
EPWM7_TZINT
(ePWM7)
0xD5C
EPWM6_TZINT
(ePWM6)
0xD5A
EPWM5_TZINT
(ePWM5)
0xD58
EPWM4_TZINT
(ePWM4)
0xD56
EPWM3_TZINT
(ePWM3)
0xD54
EPWM2_TZINT
(ePWM2)
0xD52
EPWM1_TZINT
(ePWM1)
0xD50
EPWM8_INT
(ePWM8)
0xD6E
EPWM7_INT
(ePWM7)
0xD6C
EPWM6_INT
(ePWM6)
0xD6A
EPWM5_INT
(ePWM5)
0xD68
EPWM4_INT
(ePWM4)
0xD66
EPWM3_INT
(ePWM3)
0xD64
EPWM2_INT
(ePWM2)
0xD62
EPWM1_INT
(ePWM1)
0xD60
HRCAP2_INT
(HRCAP2)
0xD7E
HRCAP1_INT
(HRCAP1)
0xD7C
Reserved
–
Reserved
–
Reserved
–
ECAP3_INT
(eCAP3)
0xD74
ECAP2_INT
(eCAP2)
0xD72
ECAP1_INT
(eCAP1)
0xD70
0xD7A
0xD78
0xD76
USB0_INT
(USB0)
0xD8E
Reserved
–
Reserved
–
HRCAP4_INT
(HRCAP4)
0xD88
HRCAP3_INT
(HRCAP3)
0xD86
Reserved
–
EQEP2_INT
(eQEP2)
0xD82
EQEP1_INT
(eQEP1)
0xD80
0xD8C
0xD8A
0xD84
Reserved
–
Reserved
–
MXINTA
(McBSP-A)
0xD9A
MRINTA
(McBSP-A)
0xD98
SPITXINTB
(SPI-B)
0xD96
SPIRXINTB
(SPI-B)
0xD94
SPITXINTA
(SPI-A)
SPIRXINTA
(SPI-A)
0xD9E
0xD9C
0xD92
0xD90
Reserved
–
Reserved
–
DINTCH6
(DMA)
DINTCH5
(DMA)
DINTCH4
(DMA)
DINTCH3
(DMA)
DINTCH2
(DMA)
DINTCH1
(DMA)
0xDAE
0xDAC
Reserved
–
0xDAA
0xDA8
0xDA6
0xDA4
0xDA2
0xDA0
Reserved
–
Reserved
–
Reserved
–
Reserved
–
Reserved
–
I2CINT2A
(I2C-A)
I2CINT1A
(I2C-A)
0xDBE
0xDBC
Reserved
–
0xDBA
0xDB8
0xDB6
0xDB4
0xDB2
0xDB0
Reserved
–
ECAN1_INTA
(CAN-A)
0xDCA
ECAN0_INTA
(CAN-A)
0xDC8
SCITXINTB
(SCI-B)
0xDC6
SCIRXINTB
(SCI-B)
0xDC4
SCITXINTA
(SCI-A)
SCIRXINTA
(SCI-A)
0xDCE
0xDCC
ADCINT7
(ADC)
0xDC2
0xDC0
ADCINT8
(ADC)
ADCINT6
(ADC)
ADCINT5
(ADC)
ADCINT4
(ADC)
ADCINT3
(ADC)
ADCINT2
(ADC)
ADCINT1
(ADC)
0xDDE
0xDDC
CLA1_INT7
(CLA)
0xDDA
0xDD8
0xDD6
0xDD4
0xDD2
0xDD0
CLA1_INT8
(CLA)
CLA1_INT6
(CLA)
CLA1_INT5
(CLA)
CLA1_INT4
(CLA)
CLA1_INT3
(CLA)
CLA1_INT2
(CLA)
CLA1_INT1
(CLA)
0xDEE
0xDEC
LVF
0xDEA
0xDE8
0xDE6
0xDE4
0xDE2
0xDE0
LUF
Reserved
–
Reserved
–
Reserved
–
Reserved
–
Reserved
–
XINT3
(CLA)
(CLA)
Ext. Int. 3
0xDF0
0xDFE
0xDFC
0xDFA
0xDF8
0xDF6
0xDF4
0xDF2
(1) Out of 96 possible interrupts, some interrupts are not used. These interrupts are reserved for future devices. These interrupts can be
used as software interrupts if they are enabled at the PIEIFRx level, provided none of the interrupts within the group is being used by a
peripheral. Otherwise, interrupts coming in from peripherals may be lost by accidentally clearing their flag while modifying the PIEIFR.
To summarize, there are two safe cases when the reserved interrupts could be used as software interrupts:
a. No peripheral within the group is asserting interrupts.
b. No peripheral interrupts are assigned to the group (for example, PIE group 7).
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
83
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-18. PIE Configuration and Control Registers
NAME
PIECTRL
ADDRESS
0x0CE0
0x0CE1
0x0CE2
0x0CE3
0x0CE4
0x0CE5
0x0CE6
0x0CE7
0x0CE8
0x0CE9
0x0CEA
0x0CEB
0x0CEC
0x0CED
0x0CEE
0x0CEF
0x0CF0
0x0CF1
0x0CF2
0x0CF3
0x0CF4
0x0CF5
0x0CF6
0x0CF7
0x0CF8
0x0CF9
SIZE (×16)
DESCRIPTION(1)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
PIE, Control Register
PIEACK
PIEIER1
PIEIFR1
PIEIER2
PIEIFR2
PIEIER3
PIEIFR3
PIEIER4
PIEIFR4
PIEIER5
PIEIFR5
PIEIER6
PIEIFR6
PIEIER7
PIEIFR7
PIEIER8
PIEIFR8
PIEIER9
PIEIFR9
PIEIER10
PIEIFR10
PIEIER11
PIEIFR11
PIEIER12
PIEIFR12
Reserved
PIE, Acknowledge Register
PIE, INT1 Group Enable Register
PIE, INT1 Group Flag Register
PIE, INT2 Group Enable Register
PIE, INT2 Group Flag Register
PIE, INT3 Group Enable Register
PIE, INT3 Group Flag Register
PIE, INT4 Group Enable Register
PIE, INT4 Group Flag Register
PIE, INT5 Group Enable Register
PIE, INT5 Group Flag Register
PIE, INT6 Group Enable Register
PIE, INT6 Group Flag Register
PIE, INT7 Group Enable Register
PIE, INT7 Group Flag Register
PIE, INT8 Group Enable Register
PIE, INT8 Group Flag Register
PIE, INT9 Group Enable Register
PIE, INT9 Group Flag Register
PIE, INT10 Group Enable Register
PIE, INT10 Group Flag Register
PIE, INT11 Group Enable Register
PIE, INT11 Group Flag Register
PIE, INT12 Group Enable Register
PIE, INT12 Group Flag Register
Reserved
0x0CFA –
0x0CFF
(1) The PIE configuration and control registers are not protected by EALLOW mode. The PIE vector
table is protected.
Copyright © 2021 Texas Instruments Incorporated
84
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.8.1 External Interrupts
Table 8-19. External Interrupt Registers
NAME
XINT1CR
ADDRESS
0x00 7070
0x00 7071
0x00 7072
0x00 7078
0x00 7079
0x00 707A
SIZE (×16)
DESCRIPTION
XINT1 configuration register
XINT2 configuration register
XINT3 configuration register
XINT1 counter register
1
1
1
1
1
1
XINT2CR
XINT3CR
XINT1CTR
XINT2CTR
XINT3CTR
XINT2 counter register
XINT3 counter register
Each external interrupt can be enabled or disabled or qualified using positive, negative, or both positive and
negative edge. For more information, see the Systems Control and Interrupts chapter of the TMS320x2806x
Technical Reference Manual .
8.8.1.1 External Interrupt Electrical Data/Timing
8.8.1.1.1 External Interrupt Timing Requirements
MIN(1)
1tc(SCO)
MAX
UNIT
cycles
cycles
Synchronous
With qualifier
(2)
tw(INT)
Pulse duration, INT input low/high
1tc(SCO) + tw(IQSW)
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
(2) This timing is applicable to any GPIO pin configured for ADCSOC functionality.
8.8.1.1.2 External Interrupt Switching Characteristics
over recommended operating conditions (unless otherwise noted)(1)
PARAMETER
MIN
MAX
tw(IQSW) + 12tc(SCO)
UNIT
td(INT)
Delay time, INT low/high to interrupt-vector fetch
cycles
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
t
w(INT)
XINT1, XINT2, XINT3
t
d(INT)
Address bus
(internal)
Interrupt Vector
Figure 8-18. External Interrupt Timing
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
85
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9 Peripherals
8.9.1 CLA Overview
The CLA extends the capabilities of the C28x CPU by adding parallel processing. Time-critical control loops
serviced by the CLA can achieve low ADC sample to output delay. Thus, the CLA enables faster system
response and higher frequency control loops. Using the CLA for time-critical tasks frees the main CPU to
perform other system and communication functions concurently. A list of major features of the CLA follows.
•
•
Clocked at the same rate as the main CPU (SYSCLKOUT)
An independent architecture allowing CLA algorithm execution independent of the main C28x CPU
– Complete bus architecture:
•
•
Program address bus and program data bus
Data address bus, data read bus, and data write bus
– Independent eight-stage pipeline
– 12-bit program counter (MPC)
– Four 32-bit result registers (MR0 to MR3)
– Two 16-bit auxillary registers (MAR0, MAR1)
– Status register (MSTF)
•
Instruction set includes:
– IEEE single-precision (32-bit) floating-point math operations
– Floating-point math with parallel load or store
– Floating-point multiply with parallel add or subtract
– 1/X and 1/sqrt(X) estimations
– Data type conversions
– Conditional branch and call
– Data load and store operations
•
•
The CLA program code can consist of up to eight tasks or ISRs.
– The start address of each task is specified by the MVECT registers.
– No limit on task size as long as the tasks fit within the CLA program memory space.
– One task at a time is serviced to completion. Tasks are not nested.
– Upon task completion, a task-specific interrupt is flagged within the PIE.
– When a task finishes, the next highest-priority pending task is automatically started.
Task trigger mechanisms:
– C28x CPU through the IACK instruction
– Task1 to Task7: the corresponding ADC, ePWM, eQEP, or eCAP module interrupt. For example:
•
•
•
•
Task1: ADCINT1 or EPWM1_INT
Task2: ADCINT2 or EPWM2_INT
Task4: ADCINT4 or EPWM4_INT or EQEPx_INT or ECAPx_INT
Task7: ADCINT7 or EPWM7_INT or EQEPx_INT or ECAPx_INT
– Task8: ADCINT8 or by CPU Timer 0 or EQEPx_INT or ECAPx_INT.
Memory and Shared Peripherals:
•
– Two dedicated message RAMs for communication between the CLA and the main CPU
– The C28x CPU can map CLA program and data memory to the main CPU space or CLA space.
– The CLA has direct access to the ADC Result registers, comparator registers, and the eCAP, eQEP, and
ePWM+HRPWM registers.
Figure 8-19 shows the CLA block diagram. Table 8-20 lists the CLA control registers.
Copyright © 2021 Texas Instruments Incorporated
86
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Peripheral Interrupts
CLA Control
Registers
IACK
ADCINT1 to ADCINT8
ECAP1_INT to ECAP3_INT
EQEP1_INT and EQEP2_INT
EPWM1_INT to EPWM8_INT
CPU Timer 0
MIFR
MIOVF
MICLR
MICLROVF
MIFRC
MIER
CLA_INT1 to CLA_INT8
Main
28x
CPU
INT11
INT12
MPERINT1
to
MPERINT8
PIE
LVF
LUF
MIRUN
Main CPU Read/Write Data Bus
MPISRCSEL1
MVECT1
MVECT2
MVECT3
MVECT4
MVECT5
MVECT6
MVECT7
MVECT8
CLA Program Address Bus
CLA Program Data Bus
CLA
Program
Memory
CLA
Data
Memory
Map to CLA or
CPU Space
Map to CLA or
CPU Space
MMEMCFG
MCTL
CLA
Shared
Message
RAMs
SYSCLKOUT
CLAENCLK
SYSRS
ADC
Result
Registers
MEALLOW
CLA Execution
Registers
ePWM
and
CLA Data Read Address Bus
HRPWM
Registers
MPC(12)
MSTF(32)
MR0(32)
MR1(32)
MR2(32)
MR3(32)
CLA Data Read Data Bus
CLA Data Write Address Bus
CLA Data Write Data Bus
Main CPU Read Data Bus
Comparator
Registers
MAR0(32)
MAR1(32)
eCAP
Registers
eQEP
Registers
Figure 8-19. CLA Block Diagram
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
87
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-20. CLA Control Registers
CLA1
ADDRESS
EALLOW
PROTECTED
REGISTER NAME
MVECT1
SIZE (×16)
DESCRIPTION(1)
0x1400
0x1401
0x1402
0x1403
0x1404
0x1405
0x1406
0x1407
0x1410
0x1411
0x1414
0x1420
0x1421
0x1422
0x1423
0x1424
0x1425
0x1426
0x1427
0x1428
0x142A
0x142B
0x142E
0x1430
0x1434
0x1438
0x143C
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
–
CLA Interrupt/Task 1 Start Address
CLA Interrupt/Task 2 Start Address
CLA Interrupt/Task 3 Start Address
CLA Interrupt/Task 4 Start Address
CLA Interrupt/Task 5 Start Address
CLA Interrupt/Task 6 Start Address
CLA Interrupt/Task 7 Start Address
CLA Interrupt/Task 8 Start Address
CLA Control Register
MVECT2
MVECT3
MVECT4
MVECT5
MVECT6
MVECT7
MVECT8
MCTL
MMEMCFG
MPISRCSEL1
MIFR
CLA Memory Configure Register
Peripheral Interrupt Source Select Register 1
Interrupt Flag Register
Interrupt Overflow Register
Interrupt Force Register
Interrupt Clear Register
Interrupt Overflow Clear Register
Interrupt Enable Register
Interrupt RUN Register
Interrupt Priority Control Register
CLA Program Counter
CLA Aux Register 0
MIOVF
MIFRC
MICLR
MICLROVF
MIER
MIRUN
MIPCTL
MPC(2)
MAR0(2)
MAR1(2)
MSTF(2)
MR0(2)
–
–
CLA Aux Register 1
–
CLA STF Register
–
CLA R0H Register
MR1(2)
–
CLA R1H Register
MR2(2)
–
CLA R2H Register
MR3(2)
–
CLA R3H Register
(1) All registers in this table are CSM-protected.
(2) The main C28x CPU has read-only access to this register for debug purposes. The main CPU cannot perform CPU or debugger writes
to this register.
Table 8-21. CLA Message RAM
ADDRESS RANGE
0x1480 – 0x14FF
0x1500 – 0x157F
SIZE (×16)
DESCRIPTION
128
CLA to CPU Message RAM
CPU to CLA Message RAM
128
Copyright © 2021 Texas Instruments Incorporated
88
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.2 Analog Block
A 12-bit ADC core is implemented that has different timings than the 12-bit ADC used on the F280x and F2833x
devices. The ADC wrapper is modified to incorporate the new timings and also other enhancements to improve
the timing control of start of conversions. Figure 8-20 shows the interaction of the analog module with the rest of
the F2806x system.
80-Pin 100-Pin
(3.3 V) VDDA
(Agnd) VSSA
VDDA
VDDA
VSSA
VREFLO
VREFLO
Tied To
VSSA
Interface Reference
Diff
VREFLO
VREFHI
A0
VREFHI
Tied To
A0
VREFHI
A0
B0
A1
A2
A3
A4
A5
A6
A7
B0
B1
B2
B3
B4
B5
B6
B7
A1
A2
A1
B1
COMP1OUT
A2
A4
A5
A6
AIO2
AIO10
10-Bit
DAC
Comp1
Comp2
B2
A3
B3
ADC
B0
B1
B2
COMP2OUT
A4
B4
AIO4
AIO12
10-Bit
DAC
B4
B5
B6
B5
Temperature Sensor
A5
A6
COMP3OUT
Signal Pinout
AIO6
AIO14
10-Bit
DAC
Comp3
B6
A7
B7
Figure 8-20. Analog Pin Configurations
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
89
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.2.1 Analog-to-Digital Converter (ADC)
8.9.2.1.1 Features
The core of the ADC contains a single 12-bit converter fed by two sample-and-hold circuits. The sample-and-
hold circuits can be sampled simultaneously or sequentially. These, in turn, are fed by a total of up to 16 analog
input channels. The converter can be configured to run with an internal band-gap reference to create true-
voltage based conversions or with a pair of external voltage references (VREFHI/VREFLO) to create ratiometric-
based conversions.
Contrary to previous ADC types, this ADC is not sequencer-based. The user can easily create a series of
conversions from a single trigger. However, the basic principle of operation is centered around the configurations
of individual conversions, called SOCs, or Start-Of-Conversions.
Functions of the ADC module include:
•
•
•
12-bit ADC core with built-in dual sample-and-hold (S/H)
Simultaneous sampling or sequential sampling modes
Full range analog input: 0 V to 3.3 V fixed, or VREFHI/VREFLO ratiometric. The digital value of the input analog
voltage is derived by:
– Internal Reference (VREFLO = VSSA. VREFHI must not exceed VDDA when using either internal or external
reference modes.)
Digital Value = 0,
when input £ 0 V
Input Analog Voltage -
VREFLO
Digital Value = 4096 ´
when 0 V < input < 3.3 V
3.3
Digital Value = 4095,
when input ³ 3.3 V
– External Reference (VREFHI/VREFLO connected to external references. VREFHI must not exceed VDDA when
using either internal or external reference modes.)
Digital Value = 0,
when input £ 0 V
Input Analog Voltage -
VREFLO
Digital Value = 4096 ´
when 0 V < input <
VREFHI
-
VREFHI VREFLO
Digital Value = 4095,
when input ³
VREFHI
•
•
•
•
Up to 16-channel, multiplexed inputs
16 SOCs, configurable for trigger, sample window, and channel
16 result registers (individually addressable) to store conversion values
Multiple trigger sources
– S/W – software immediate start
– ePWM 1–8
– GPIO XINT2
– CPU Timer 0, CPU Timer 1, CPU Timer 2
– ADCINT1, ADCINT2
•
9 flexible PIE interrupts, can configure interrupt request after any conversion
Copyright © 2021 Texas Instruments Incorporated
90
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-22. ADC Configuration and Control Registers
EALLOW
PROTECTE
D
SIZE
(×16)
REGISTER NAME
ADDRESS
DESCRIPTION
ADCCTL1
0x7100
0x7101
0x7104
0x7105
0x7106
0x7107
0x7108
0x7109
0x710A
0x710B
0x710C
0x7110
0x7112
0x7114
0x7115
0x7118
0x711A
0x711C
0x711E
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Yes
Yes
No
Control 1 Register
Control 2 Register
Interrupt Flag Register
ADCCTL2
ADCINTFLG
ADCINTFLGCLR
ADCINTOVF
No
Interrupt Flag Clear Register
No
Interrupt Overflow Register
ADCINTOVFCLR
INTSEL1N2
No
Interrupt Overflow Clear Register
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Interrupt 1 and 2 Selection Register
INTSEL3N4
Interrupt 3 and 4 Selection Register
INTSEL5N6
Interrupt 5 and 6 Selection Register
INTSEL7N8
Interrupt 7 and 8 Selection Register
INTSEL9N10
Interrupt 9 Selection Register (reserved Interrupt 10 Selection)
SOC Priority Control Register
SOCPRICTL
ADCSAMPLEMODE
ADCINTSOCSEL1
ADCINTSOCSEL2
ADCSOCFLG1
ADCSOCFRC1
ADCSOCOVF1
ADCSOCOVFCLR1
Sampling Mode Register
Interrupt SOC Selection 1 Register (for 8 channels)
Interrupt SOC Selection 2 Register (for 8 channels)
SOC Flag 1 Register (for 16 channels)
SOC Force 1 Register (for 16 channels)
SOC Overflow 1 Register (for 16 channels)
SOC Overflow Clear 1 Register (for 16 channels)
SOC0 Control Register to SOC15 Control Register
No
No
No
ADCSOC0CTL to
ADCSOC15CTL
0x7120 –
0x712F
1
Yes
ADCREFTRIM
ADCOFFTRIM
COMPHYSTCTL
ADCREV
0x7140
0x7141
0x714C
0x714F
1
1
1
1
Yes
Yes
Yes
No
Reference Trim Register
Offset Trim Register
Comparator Hysteresis Control Register
Revision Register
Table 8-23. ADC Result Registers (Mapped to PF0)
SIZE
(×16)
EALLOW
PROTECTED
REGISTER NAME
ADCRESULT0 to ADCRESULT15
ADDRESS
DESCRIPTION
0xB00 to
0xB0F
1
No
ADC Result 0 Register to ADC Result 15 Register
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
91
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
0-Wait
Result
Registers
PF0 (CPU)
PF2 (CPU)
SYSCLKOUT
ADCENCLK
ADCINT 1
PIE
ADCINT 9
TINT 0
CPUTIMER 0
CPUTIMER 1
CPUTIMER 2
ADCTRIG 1
ADCTRIG 2
ADCTRIG 3
TINT 1
TINT 2
ADC
Core
12-Bit
XINT 2SOC
AIO
MUX
ADC
Channels
XINT 2
EPWM 1
EPWM 2
EPWM 3
EPWM 4
EPWM 5
EPWM 6
EPWM 7
EPWM 8
ADCTRIG 4
SOCA 1
SOCB 1
SOCA 2
SOCB 2
SOCA 3
SOCB 3
SOCA 4
SOCB 4
SOCA 5
SOCB 5
SOCA 6
SOCB 6
SOCA 7
SOCB 7
SOCA 8
SOCB 8
ADCTRIG 5
ADCTRIG 6
ADCTRIG 7
ADCTRIG 8
ADCTRIG 9
ADCTRIG 10
ADCTRIG 11
ADCTRIG 12
ADCTRIG 13
ADCTRIG 14
ADCTRIG 15
ADCTRIG 16
ADCTRIG 17
ADCTRIG 18
ADCTRIG 19
ADCTRIG 20
Figure 8-21. ADC Connections
ADC Connections if the ADC is Not Used
TI recommends keeping the connections for the analog power pins, even if the ADC is not used. Following is a
summary of how the ADC pins should be connected, if the ADC is not used in an application:
•
•
•
•
VDDA – Connect to VDDIO
VSSA – Connect to VSS
VREFLO – Connect to VSS
ADCINAn, ADCINBn, VREFHI – Connect to VSSA
When the ADC module is used in an application, unused ADC input pins should be connected to analog ground
(VSSA).
Note
TI recommends that unused ADCIN pins which are multiplexed with AIO function be grounded through
a 1-kΩ resistor. This recommendation is intended to prevent any inadvertent software activation of the
AIO output logic-high driving directly to ground; this condition can cause permanent device damage by
exceeding IOH Absolute Maximum.
When the ADC is not used, be sure that the clock to the ADC module is not turned on to realize power savings.
Copyright © 2021 Texas Instruments Incorporated
92
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.2.1.2 ADC Start-of-Conversion Electrical Data/Timing
8.9.2.1.2.1 External ADC Start-of-Conversion Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
MAX
UNIT
tw(ADCSOCL)
Pulse duration, ADCSOCxO low
32tc(HCO)
cycles
tw(ADCSOCL)
ADCSOCAO
or
ADCSOCBO
Figure 8-22. ADCSOCAO or ADCSOCBO Timing
8.9.2.1.3 On-Chip Analog-to-Digital Converter (ADC) Electrical Data/Timing
8.9.2.1.3.1 ADC Electrical Characteristics
PARAMETER
DC SPECIFICATIONS
MIN
TYP
MAX
UNIT
Resolution
12
Bits
ADC clock
90-MHz device
0.001
45
64
MHz
ADC
Clocks
Sample Window
7
ACCURACY
INL (Integral nonlinearity)(1)
–4
–1
4
LSB
LSB
DNL (Differential nonlinearity), no missing codes
1.5
Executing a single self-
recalibration(3)
–20
–4
20
4
Offset error (2)
LSB
Executing periodic self-
recalibration(4)
Overall gain error with internal reference
Overall gain error with external reference
Channel-to-channel offset variation
Channel-to-channel gain variation
ADC temperature coefficient with internal reference
ADC temperature coefficient with external reference
VREFLO
–60
–40
–4
60
40
4
LSB
LSB
LSB
–4
4
LSB
–50
–20
ppm/°C
ppm/°C
µA
–100
100
VREFHI
µA
ANALOG INPUT
Analog input voltage with internal reference
Analog input voltage with external reference
VREFLO input voltage(5)
0
VREFLO
VSSA
3.3
VREFHI
0.66
V
V
V
2.64
VDDA
VDDA
VREFHI input voltage(6)
V
with VREFLO = VSSA
1.98
Input capacitance
5
pF
μA
Input leakage current
±2
(1) INL will degrade when the ADC input voltage goes above VDDA
.
(2) 1 LSB has the weighted value of full-scale range (FSR)/4096. FSR is 3.3 V with internal reference and VREFHI - VREFLO for external
reference.
(3) For more details, see the TMS320F2806x MCUs Silicon Errata.
(4) Periodic self-recalibration will remove system-level and temperature dependencies on the ADC zero offset error.
(5) VREFLO is always connected to VSSA on the 80-pin PN and PFP devices.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
93
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
(6) VREFHI must not exceed VDDA when using either internal or external reference modes. Because VREFHI is tied to ADCINA0 on the 80-
pin PN and PFP devices, the input signal on ADCINA0 must not exceed VDDA
.
8.9.2.1.3.2 ADC Power Modes
ADC OPERATING MODE
CONDITIONS
IDDA
UNIT
ADC Clock Enabled
Band gap On (ADCBGPWD = 1)
Reference On (ADCREFPWD = 1)
ADC Powered Up (ADCPWDN = 1)
Mode A – Operating Mode
16
mA
ADC Clock Enabled
Band gap On (ADCBGPWD = 1)
Reference On (ADCREFPWD = 1)
ADC Powered Up (ADCPWDN = 0)
Mode B – Quick Wake Mode
Mode C – Comparator-Only Mode
Mode D – Off Mode
4
mA
mA
mA
ADC Clock Enabled
Band gap On (ADCBGPWD = 1)
Reference On (ADCREFPWD = 0)
ADC Powered Up (ADCPWDN = 0)
1.5
ADC Clock Enabled
Band gap On (ADCBGPWD = 0)
Reference On (ADCREFPWD = 0)
ADC Powered Up (ADCPWDN = 0)
0.075
8.9.2.1.3.3 Internal Temperature Sensor
8.9.2.1.3.3.1 Temperature Sensor Coefficient
PARAMETER(1)
MIN
TYP
0.18(3) (2)
1750
MAX
UNIT
°C/LSB
LSB
Degrees C of temperature movement per measured ADC LSB change of
the temperature sensor
TSLOPE
TOFFSET
ADC output at 0°C of the temperature sensor
(1) The temperature sensor slope and offset are given in terms of ADC LSBs using the internal reference of the ADC. Values must be
adjusted accordingly in external reference mode to the external reference voltage.
(2) Output of the temperature sensor (in terms of LSBs) is sign-consistent with the direction of the temperature movement. Increasing
temperatures will give increasing ADC values relative to an initial value; decreasing temperatures will give decreasing ADC values
relative to an initial value.
(3) ADC temperature coeffieicient is accounted for in this specification
8.9.2.1.3.4 ADC Power-Up Control Bit Timing
8.9.2.1.3.4.1 ADC Power-Up Delays
PARAMETER(1)
MIN
MAX
UNIT
td(PWD)
Delay time for the ADC to be stable after power up
1
ms
(1) Timings maintain compatibility to the ADC module. The 2806x ADC supports driving all 3 bits at the same time td(PWD) ms before first
conversion.
ADCPWDN/
ADCBGPWD/
ADCREFPWD/
ADCENABLE
td(PWD)
Request for ADC
Conversion
Figure 8-23. ADC Conversion Timing
Copyright © 2021 Texas Instruments Incorporated
94
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Ron
3.4 kW
Switch
Rs
ADCIN
Cp
Ch
Source
Signal
ac
5 pF
1.6 pF
28x DSP
Typical Values of the Input Circuit Components:
Switch Resistance (Ron): 3.4 kW
Sampling Capacitor (Ch): 1.6 pF
Parasitic Capacitance (Cp): 5 pF
Source Resistance (Rs): 50 W
Figure 8-24. ADC Input Impedance Model
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
95
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.2.1.3.5 ADC Sequential and Simultaneous Timings
Analog Input
SOC0 Sample
Window
SOC1 Sample
Window
SOC2 Sample
Window
0
2
9
15
22 24
37
ADCCLK
ADCCTL1.INTPULSEPOS
ADCSOCFLG1.SOC0
ADCSOCFLG1.SOC1
ADCSOCFLG1.SOC2
S/H Window Pulse to Core
ADCRESULT 0
SOC0
SOC1
SOC2
Result 0 Latched
2 ADCCLKs
ADCRESULT 1
EOC0 Pulse
EOC1 Pulse
ADCINTFLG.ADCINTx
Minimum
7 ADCCLKs
Conversion 0
13 ADC Clocks
1 ADCCLK
6
Minimum
ADCCLKs 7 ADCCLKs
Conversion 1
13 ADC Clocks
Figure 8-25. Timing Example for Sequential Mode / Late Interrupt Pulse
Copyright © 2021 Texas Instruments Incorporated
96
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Analog Input
SOC0 Sample
Window
SOC1 Sample
Window
SOC2 Sample
Window
0
2
9
15
22 24
37
ADCCLK
ADCCTL1.INTPULSEPOS
ADCSOCFLG1.SOC0
ADCSOCFLG1.SOC1
ADCSOCFLG1.SOC2
S/H Window Pulse to Core
ADCRESULT 0
SOC0
SOC1
SOC2
Result 0 Latched
ADCRESULT 1
EOC0 Pulse
EOC1 Pulse
EOC2 Pulse
ADCINTFLG.ADCINTx
Minimum
7 ADCCLKs
Conversion 0
13 ADC Clocks
2 ADCCLKs
6
Minimum
ADCCLKs 7 ADCCLKs
Conversion 1
13 ADC Clocks
Figure 8-26. Timing Example for Sequential Mode / Early Interrupt Pulse
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
97
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Analog Input A
SOC0 Sample
A Window
SOC2 Sample
A Window
Analog Input B
SOC0 Sample
B Window
SOC2 Sample
B Window
0
2
9
22 24
37
50
ADCCLK
ADCCTL1.INTPULSEPOS
ADCSOCFLG1.SOC0
ADCSOCFLG1.SOC1
ADCSOCFLG1.SOC2
S/H Window Pulse to Core
ADCRESULT 0
SOC0 (A/B)
SOC2 (A/B)
2 ADCCLKs
Result 0 (A) Latched
ADCRESULT 1
Result 0 (B) Latched
ADCRESULT 2
EOC0 Pulse
EOC1 Pulse
1 ADCCLK
EOC2 Pulse
ADCINTFLG .ADCINTx
Minimum
7 ADCCLKs
Conversion 0 (A)
13 ADC Clocks
Conversion 0 (B)
13 ADC Clocks
2 ADCCLKs
19
ADCCLKs
Minimum
7 ADCCLKs
Conversion 1 (A)
13 ADC Clocks
Figure 8-27. Timing Example for Simultaneous Mode / Late Interrupt Pulse
Copyright © 2021 Texas Instruments Incorporated
98
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Analog Input A
Analog Input B
SOC0 Sample
A Window
SOC2 Sample
A Window
SOC0 Sample
B Window
SOC2 Sample
B Window
0
2
9
22 24
37
50
ADCCLK
ADCCTL1.INTPULSEPOS
ADCSOCFLG1.SOC0
ADCSOCFLG1.SOC1
ADCSOCFLG1.SOC2
S/H Window Pulse to Core
ADCRESULT 0
SOC0 (A/B)
SOC2 (A/B)
Result 0 (A) Latched
2 ADCCLKs
Result 0 (B) Latched
ADCRESULT 1
ADCRESULT 2
EOC0 Pulse
EOC1 Pulse
EOC2 Pulse
ADCINTFLG.ADCINTx
Conversion 0 (A)
13 ADC Clocks
Conversion 0 (B)
13 ADC Clocks
Minimum
2 ADCCLKs
7 ADCCLKs
19
Minimum
7 ADCCLKs
Conversion 1 (A)
13 ADC Clocks
ADCCLKs
Figure 8-28. Timing Example for Simultaneous Mode / Early Interrupt Pulse
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
99
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.2.2 ADC MUX
To COMPy A or B input
To ADC Channel X
Logic implemented in GPIO MUX block
AIOx Pin
SYSCLK
AIOxIN
1
AIOxINE
AIODAT Reg
(Read)
SYNC
0
AIODAT Reg
(Latch)
AIOMUX 1 Reg
AIOSET,
AIOCLEAR,
AIOTOGGLE
Regs
AIODIR Reg
(Latch)
1
(0 = Input, 1 = Output)
0
0
Figure 8-29. AIOx Pin Multiplexing
The ADC channel and Comparator functions are always available. The digital I/O function is available only when
the respective bit in the AIOMUX1 register is 0. In this mode, reading the AIODAT register reflects the actual pin
state.
The digital I/O function is disabled when the respective bit in the AIOMUX1 register is 1. In this mode, reading
the AIODAT register reflects the output latch of the AIODAT register and the input digital I/O buffer is disabled to
prevent analog signals from generating noise.
On reset, the digital function is disabled. If the pin is used as an analog input, users should keep the AIO
function disabled for that pin.
Copyright © 2021 Texas Instruments Incorporated
100 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.2.3 Comparator Block
Figure 8-30 shows the interaction of the Comparator modules with the rest of the system.
COMP x A
+
COMP x B
COMP
TZ1/2/3
-
GPIO
MUX
COMP x
+
DAC x
Wrapper
ePWM
AIO
MUX
COMPxOUT
DAC
Core
10-Bit
Figure 8-30. Comparator Block Diagram
Table 8-24. Comparator Control Registers
REGISTER
NAME
COMP1
ADDRESS
COMP2
ADDRESS
COMP3
ADDRESS
SIZE
(×16)
EALLOW
PROTECTED
DESCRIPTION
COMPCTL
0x6400
0x6402
0x6404
0x6406
0x6420
0x6422
0x6424
0x6426
0x6440
0x6442
0x6444
0x6446
1
1
1
1
Yes
No
Comparator Control Register
Comparator Status Register
DAC Control Register
COMPSTS
DACCTL
DACVAL
Yes
No
DAC Value Register
RAMPMAXREF_
ACTIVE
Ramp Generator Maximum Reference
(Active) Register
0x6408
0x640A
0x640C
0x6428
0x642A
0x642C
0x6448
0x644A
0x644C
1
1
1
No
No
No
RAMPMAXREF_
SHDW
Ramp Generator Maximum Reference
(Shadow) Register
RAMPDECVAL_
ACTIVE
Ramp Generator Decrement Value
(Active) Register
RAMPDECVAL_
SHDW
Ramp Generator Decrement Value
(Shadow) Register
0x640E
0x6410
0x642E
0x6430
0x644E
0x6450
1
1
No
No
RAMPSTS
Ramp Generator Status Register
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 101
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
www.ti.com
UNIT
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
8.9.2.3.1 On-Chip Comparator/DAC Electrical Data/Timing
8.9.2.3.1.1 Electrical Characteristics of the Comparator/DAC
CHARACTERISTIC
MIN
TYP
MAX
Comparator
Comparator Input Range
VSSA – VDDA
V
Comparator response time to PWM Trip Zone (Async)
30
±5
35
ns
Input Offset
mV
mV
Input Hysteresis(1)
DAC
DAC Output Range
DAC resolution
DAC settling time
DAC Gain
VSSA – VDDA
V
10
bits
See Figure 8-31.
–1.5%
10
DAC Offset
Monotonic
mV
Yes
±3
INL
LSB
(1) Hysteresis on the comparator inputs is achieved with a Schmidt trigger configuration. This results in an effective 100-kΩ feedback
resistance between the output of the comparator and the non-inverting input of the comparator.
1100
1000
900
800
700
600
500
400
300
200
100
0
0
50
100
150
200
250
300
350
400
450
500
DAC Step Size (Codes)
DAC Accuracy
15 Codes
7 Codes
3 Codes
1 Code
Figure 8-31. DAC Settling Time
Copyright © 2021 Texas Instruments Incorporated
102 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.3 Detailed Descriptions
Integral Nonlinearity
Integral nonlinearity refers to the deviation of each individual code from a line drawn from zero to full scale. The
point used as zero occurs one-half LSB before the first code transition. The full-scale point is defined as level
one-half LSB beyond the last code transition. The deviation is measured from the center of each particular code
to the true straight line between these two points.
Differential Nonlinearity
An ideal ADC exhibits code transitions that are exactly 1 LSB apart. DNL is the deviation from this ideal value. A
differential nonlinearity error of less than ±1 LSB ensures no missing codes.
Zero Offset
The major carry transition should occur when the analog input is at zero volts. Zero error is defined as the
deviation of the actual transition from that point.
Gain Error
The first code transition should occur at an analog value one-half LSB above negative full scale. The last
transition should occur at an analog value one and one-half LSB below the nominal full scale. Gain error is the
deviation of the actual difference between first and last code transitions and the ideal difference between first
and last code transitions.
Signal-to-Noise Ratio + Distortion (SINAD)
SINAD is the ratio of the rms value of the measured input signal to the rms sum of all other spectral components
below the Nyquist frequency, including harmonics but excluding DC. The value for SINAD is expressed in
decibels.
Effective Number of Bits (ENOB)
For a sine wave, SINAD can be expressed in terms of the number of bits. Using the following formula,
(SINAD -1.76)
N =
6.02
it is possible to get a measure of performance expressed as N, the effective number of bits.
Thus, effective number of bits for a device for sine wave inputs at a given input frequency can be calculated
directly from its measured SINAD.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first nine harmonic components to the rms value of the measured input
signal and is expressed as a percentage or in decibels.
Spurious Free Dynamic Range (SFDR)
SFDR is the difference in dB between the rms amplitude of the input signal and the peak spurious signal.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 103
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.4 Serial Peripheral Interface (SPI) Module
The device includes the 4-pin serial peripheral interface (SPI) module. Up to two SPI modules are available. The
SPI is a high-speed, synchronous serial I/O port that allows a serial bit stream of programmed length (1 to
16 bits) to be shifted into and out of the device at a programmable bit-transfer rate. Normally, the SPI is used for
communications between the MCU and external peripherals or another processor. Typical applications include
external I/O or peripheral expansion through devices such as shift registers, display drivers, and ADCs.
Multidevice communications are supported by the master/slave operation of the SPI.
The SPI module features include:
•
Four external pins:
– SPISOMI: SPI slave-output/master-input pin
– SPISIMO: SPI slave-input/master-output pin
– SPISTE: SPI slave transmit-enable pin
– SPICLK: SPI serial-clock pin
Note
All four pins can be used as GPIO if the SPI module is not used.
•
Two operational modes: master and slave
Baud rate: 125 different programmable rates.
LSPCLK
Baud rate =
Baud rate =
when SPIBRR = 3 to127
when SPIBRR = 0,1, 2
(SPIBRR + 1)
LSPCLK
4
•
•
Data word length: 1 to 16 data bits
Four clocking schemes (controlled by clock polarity and clock phase bits) include:
– Falling edge without phase delay: SPICLK active-high. SPI transmits data on the falling edge of the
SPICLK signal and receives data on the rising edge of the SPICLK signal.
– Falling edge with phase delay: SPICLK active-high. SPI transmits data one half-cycle ahead of the falling
edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal.
– Rising edge without phase delay: SPICLK inactive-low. SPI transmits data on the rising edge of the
SPICLK signal and receives data on the falling edge of the SPICLK signal.
– Rising edge with phase delay: SPICLK inactive-low. SPI transmits data one half-cycle ahead of the rising
edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.
Simultaneous receive and transmit operation (transmit function can be disabled in software)
Transmitter and receiver operations are accomplished through either interrupt-driven or polled algorithms.
Nine SPI module control registers: In control register frame beginning at address 7040h.
•
•
•
Note
All registers in this module are 16-bit registers that are connected to Peripheral Frame 2. When a
register is accessed, the register data is in the lower byte (7–0), and the upper byte (15–8) is read
as zeros. Writing to the upper byte has no effect.
Copyright © 2021 Texas Instruments Incorporated
104 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Enhanced feature:
•
•
•
•
4-level transmit/receive FIFO
Delayed transmit control
Bidirectional 3 wire SPI mode support
Audio data receive support through SPISTE inversion
The SPI port operation is configured and controlled by the registers listed in Table 8-25 and Table 8-26.
Table 8-25. SPI-A Registers
NAME
SPICCR
ADDRESS
0x7040
0x7041
0x7042
0x7044
0x7046
0x7047
0x7048
0x7049
0x704A
0x704B
0x704C
0x704F
SIZE (×16) EALLOW PROTECTED
DESCRIPTION(1)
SPI-A Configuration Control Register
SPI-A Operation Control Register
SPI-A Status Register
1
1
1
1
1
1
1
1
1
1
1
1
No
No
No
No
No
No
No
No
No
No
No
No
SPICTL
SPISTS
SPIBRR
SPI-A Baud Rate Register
SPIRXEMU
SPIRXBUF
SPITXBUF
SPIDAT
SPI-A Receive Emulation Buffer Register
SPI-A Serial Input Buffer Register
SPI-A Serial Output Buffer Register
SPI-A Serial Data Register
SPIFFTX
SPIFFRX
SPIFFCT
SPIPRI
SPI-A FIFO Transmit Register
SPI-A FIFO Receive Register
SPI-A FIFO Control Register
SPI-A Priority Control Register
(1) Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined
results.
Table 8-26. SPI-B Registers
NAME
SPICCR
ADDRESS
0x7740
0x7741
0x7742
0x7744
0x7746
0x7747
0x7748
0x7749
0x774A
0x774B
0x774C
0x774F
SIZE (×16) EALLOW PROTECTED
DESCRIPTION(1)
SPI-B Configuration Control Register
SPI-B Operation Control Register
SPI-B Status Register
1
1
1
1
1
1
1
1
1
1
1
1
No
No
No
No
No
No
No
No
No
No
No
No
SPICTL
SPISTS
SPIBRR
SPI-B Baud Rate Register
SPIRXEMU
SPIRXBUF
SPITXBUF
SPIDAT
SPI-B Receive Emulation Buffer Register
SPI-B Serial Input Buffer Register
SPI-B Serial Output Buffer Register
SPI-B Serial Data Register
SPIFFTX
SPIFFRX
SPIFFCT
SPIPRI
SPI-B FIFO Transmit Register
SPI-B FIFO Receive Register
SPI-B FIFO Control Register
SPI-B Priority Control Register
(1) Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined
results.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 105
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Figure 8-32 is a block diagram of the SPI in slave mode.
SPIFFENA
Overrun
INT ENA
Receiver
Overrun Flag
SPIFFTX.14
RX FIFO Registers
SPIRXBUF
SPISTS.7
SPICTL.4
RX FIFO _0
RX FIFO _1
-----
SPIINT
RX FIFO Interrupt
RX Interrupt
Logic
RX FIFO _3
16
SPIRXBUF
Buffer Register
SPIFFOVF
FLAG
SPIFFRX.15
To CPU
TX FIFO Registers
SPITXBUF
TX FIFO _3
TX Interrupt
Logic
TX FIFO Interrupt
-----
TX FIFO _1
SPITX
TX FIFO _0
16
SPI INT
ENA
16
SPI INT FLAG
SPITXBUF
Buffer Register
SPISTS.6
SPICTL.0
TRIWIRE
SPIPRI.0
16
M
S
M
SPIDAT
Data Register
TW
S
SW1
SW2
SPISIMO
SPISOMI
M
S
TW
SPIDAT.15 - 0
M
S
TW
STEINV
SPIPRI.1
Talk
STEINV
SPICTL.1
SPISTE
State Control
Master/Slave
SPICTL.2
SPI Char
LSPCLK
SPICCR.3 - 0
S
SW3
3
2
1
0
Clock
Polarity
Clock
Phase
M
S
SPI Bit Rate
SPIBRR.6 - 0
SPICCR.6
SPICTL.3
SPICLK
M
6
5
4
3
2
1
0
A. SPISTE is driven low by the master for a slave device.
Figure 8-32. SPI Module Block Diagram (Slave Mode)
Copyright © 2021 Texas Instruments Incorporated
106 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.4.1 SPI Master Mode Electrical Data/Timing
Section 8.9.4.1.1 lists the master mode timing (clock phase = 0) and Section 8.9.4.1.2 lists the master mode
timing (clock phase = 1). Figure 8-33 and Figure 8-34 show the timing waveforms.
8.9.4.1.1 SPI Master Mode External Timing (Clock Phase = 0)
NO.(1)
BRR EVEN
MIN
BRR ODD
MIN
(2) (3) (4)
PARAMETER
UNIT
(5)
MAX
MAX
1
tc(SPC)M
Cycle time, SPICLK
4tc(LSPCLK)
128tc(LSPCLK)
5tc(LSPCLK)
127tc(LSPCLK)
ns
ns
Pulse duration, SPICLK first
pulse
0.5tc(SPC)M + 0.5tc(LSPCLK)
– 10
0.5tc(SPC)M
+
2
3
tw(SPC1)M
0.5tc(SPC)M – 10
0.5tc(SPC)M + 10
0.5tc(SPC)M + 10
10
0.5tc(LSPCLK) + 10
Pulse duration, SPICLK second
pulse
0.5tc(SPC)M – 0.5tc(LSPCLK)
– 10
0.5tc(SPC)M
–
tw(SPC2)M
td(SIMO)M
tv(SIMO)M
tsu(SOMI)M
th(SOMI)M
td(SPC)M
td(STE)M
0.5tc(SPC)M – 10
ns
ns
ns
ns
ns
ns
ns
0.5tc(LSPCLK) + 10
Delay time, SPICLK to
SPISIMO valid
4
10
Valid time, SPISIMO valid after
SPICLK
0.5tc(SPC)M – 0.5tc(LSPCLK)
– 10
5
0.5tc(SPC)M – 10
Setup time, SPISOMI before
SPICLK
8
26
0
26
0
Hold time, SPISOMI valid after
SPICLK
9
Delay time, SPISTE active to
SPICLK
1.5tc(SPC)M
–
1.5tc(SPC)M –
3tc(SYSCLK) – 10
23
24
3tc(SYSCLK) – 10
Delay time, SPICLK to SPISTE
inactive
0.5tc(SPC)M – 0.5tc(LSPCLK)
– 10
0.5tc(SPC)M – 10
(1) The MASTER / SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is cleared.
(2) tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR +1)
(3) tc(LCO) = LSPCLK cycle time
(4) Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25-MHz MAX, master mode receive 12.5-MHz MAX
Slave mode transmit 12.5-MAX, slave mode receive 12.5-MHz MAX.
(5) The active edge of the SPICLK signal referenced is controlled by the clock polarity bit (SPICCR.6).
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 107
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
1
SPICLK
(clock polarity = 0)
2
3
SPICLK
(clock polarity = 1)
4
5
SPISIMO
Master Out Data Is Valid
8
9
Master In Data
Must Be Valid
SPISOMI
SPISTE
24
23
Figure 8-33. SPI Master Mode External Timing (Clock Phase = 0)
8.9.4.1.2 SPI Master Mode External Timing (Clock Phase = 1)
NO.(1)
BRR EVEN
MIN
BRR ODD
MIN
(2) (3) (4)
PARAMETER
UNIT
(5)
MAX
MAX
127tc(LSPCLK)
0.5tc(SPC)M –
1
tc(SPC)M
Cycle time, SPICLK
4tc(LSPCLK)
128tc(LSPCLK)
5tc(LSPCLK)
0.5tc(SPC)M
ns
ns
Pulse duration, SPICLK first
pulse
–
2
3
tw(SPC1)M
0.5tc(SPC)M – 10
0.5tc(SPC)M + 10
0.5tc(SPC)M + 10
0.5tc(LSPCLK) – 10
0.5tc(LSPCLK) + 10
Pulse duration, SPICLK second
pulse
0.5tc(SPC)M
+
0.5tc(SPC)M
0.5tc(LSPCLK) + 10
+
tw(SPC2)M
td(SIMO)M
tv(SIMO)M
tsu(SOMI)M
th(SOMI)M
td(SPC)M
td(STE)M
0.5tc(SPC)M – 10
ns
ns
ns
ns
ns
ns
ns
0.5tc(LSPCLK) – 10
Delay time, SPISIMO valid to
SPICLK
0.5tc(SPC)M
+
6
0.5tc(SPC)M – 10
0.5tc(LSPCLK) – 10
Valid time, SPISIMO valid after
SPICLK
0.5tc(SPC)M
–
7
0.5tc(SPC)M – 10
0.5tc(LSPCLK) – 10
Setup time, SPISOMI before
SPICLK
10
11
23
24
26
0
26
Hold time, SPISOMI valid after
SPICLK
0
Delay time, SPISTE active to
SPICLK
2tc(SPC)M
–
2tc(SPC)M
–
3tc(SYSCLK) – 10
3tc(SYSCLK) – 10
Delay time, SPICLK to SPISTE
inactive
0.5tc(SPC)
–
0.5tc(SPC) – 10
0.5tc(LSPCLK) – 10
(1) The MASTER/SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is set.
(2) tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
(3) Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25 MHz MAX, master mode receive 12.5 MHz MAX
Slave mode transmit 12.5 MHz MAX, slave mode receive 12.5 MHz MAX.
(4) tc(LCO) = LSPCLK cycle time
(5) The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
Copyright © 2021 Texas Instruments Incorporated
108 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
1
SPICLK
(clock polarity = 0)
2
3
SPICLK
(clock polarity = 1)
6
7
SPISIMO
Master Out Data Is Valid
10
11
Master In Data Must
Be Valid
SPISOMI
SPISTE
24
23
Figure 8-34. SPI Master Mode External Timing (Clock Phase = 1)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 109
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.4.2 SPI Slave Mode Electrical Data/Timing
Section 8.9.4.2.1 lists the slave mode timing (clock phase = 0) and Section 8.9.4.2.2 lists the slave mode timing
(clock phase = 1). Figure 8-35 and Figure 8-36 show the timing waveforms.
8.9.4.2.1 SPI Slave Mode External Timing (Clock Phase = 0) (1) (2) (4) (3) (5)
NO.
PARAMETER
Cycle time, SPICLK
MIN
4tc(SYSCLK)
MAX UNIT
12 tc(SPC)S
13 tw(SPC1)S
14 tw(SPC2)S
15 td(SOMI)S
16 tv(SOMI)S
19 tsu(SIMO)S
20 th(SIMO)S
25 tsu(STE)S
26 th(STE)S
ns
ns
ns
Pulse duration, SPICLK first pulse
2tc(SYSCLK) – 1
2tc(SYSCLK) – 1
Pulse duration, SPICLK second pulse
Delay time, SPICLK to SPISOMI valid
Valid time, SPISOMI data valid after SPICLK
Setup time, SPISIMO valid before SPICLK
Hold time, SPISIMO data valid after SPICLK
Setup time, SPISTE active before SPICLK
Hold time, SPISTE inactive after SPICLK
21
ns
ns
ns
ns
ns
ns
0
1.5tc(SYSCLK)
1.5tc(SYSCLK)
1.5tc(SYSCLK)
1.5tc(SYSCLK)
(1) The MASTER / SLAVE bit (SPICTL.2) is cleared and the CLOCK PHASE bit (SPICTL.3) is cleared.
(2) tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
(3) tc(LCO) = LSPCLK cycle time
(4) Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25-MHz MAX, master mode receive 12.5-MHz MAX
Slave mode transmit 12.5-MHz MAX, slave mode receive 12.5-MHz MAX.
(5) The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
12
SPICLK
(clock polarity = 0)
13
14
SPICLK
(clock polarity = 1)
15
16
SPISOMI
SPISOMI Data Is Valid
19
20
SPISIMO Data
Must Be Valid
SPISIMO
SPISTE
25
26
Figure 8-35. SPI Slave Mode External Timing (Clock Phase = 0)
Copyright © 2021 Texas Instruments Incorporated
110
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.4.2.2 SPI Slave Mode External Timing (Clock Phase = 1) (1) (2) (3) (4)
NO.
PARAMETER
Cycle time, SPICLK
MIN
4tc(SYSCLK)
MAX UNIT
12 tc(SPC)S
13 tw(SPC1)S
14 tw(SPC2)S
17 td(SOMI)S
18 tv(SOMI)S
21 tsu(SIMO)S
22 th(SIMO)S
25 tsu(STE)S
26 th(STE)S
ns
ns
ns
Pulse duration, SPICLK first pulse
2tc(SYSCLK) – 1
2tc(SYSCLK) – 1
Pulse duration, SPICLK second pulse
Delay time, SPICLK to SPISOMI valid
Valid time, SPISOMI data valid after SPICLK
Setup time, SPISIMO valid before SPICLK
Hold time, SPISIMO data valid after SPICLK
Setup time, SPISTE active before SPICLK
Hold time, SPISTE inactive after SPICLK
21
ns
ns
ns
ns
ns
ns
0
1.5tc(SYSCLK)
1.5tc(SYSCLK)
1.5tc(SYSCLK)
1.5tc(SYSCLK)
(1) The MASTER / SLAVE bit (SPICTL.2) is cleared and the CLOCK PHASE bit (SPICTL.3) is cleared.
(2) tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
(3) Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25-MHz MAX, master mode receive 12.5-MHz MAX
Slave mode transmit 12.5-MHz MAX, slave mode receive 12.5-MHz MAX.
(4) The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
12
SPICLK
(clock polarity = 0)
13
14
SPICLK
(clock polarity = 1)
17
SPISOMI
SPISOMI Data Is Valid
Data Valid
Data Valid
18
21
22
SPISIMO Data
Must Be Valid
SPISIMO
SPISTE
26
25
Figure 8-36. SPI Slave Mode External Timing (Clock Phase = 1)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
111
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.5 Serial Communications Interface (SCI) Module
The devices include two serial communications interface (SCI) modules (SCI-A, SCI-B). The SCI module
supports digital communications between the CPU and other asynchronous peripherals that use the standard
non-return-to-zero (NRZ) format. The SCI receiver and transmitter are double-buffered, and each has its own
separate enable and interrupt bits. Both can be operated independently or simultaneously in the full-duplex
mode. To ensure data integrity, the SCI checks received data for break detection, parity, overrun, and framing
errors. The bit rate is programmable to over 65000 different speeds through a 16-bit baud-select register.
Features of each SCI module include:
•
Two external pins:
– SCITXD: SCI transmit-output pin
– SCIRXD: SCI receive-input pin
Note
Both pins can be used as GPIO if not used for SCI.
– Baud rate programmable to 64K different rates:
LSPCLK
Baud rate =
Baud rate =
when BRR ¹ 0
when BRR = 0
(BRR + 1) * 8
LSPCLK
16
•
Data-word format
– One start bit
– Data-word length programmable from 1 to 8 bits
– Optional even/odd/no parity bit
– One or 2 stop bits
•
•
•
•
•
Four error-detection flags: parity, overrun, framing, and break detection
Two wake-up multiprocessor modes: idle-line and address bit
Half- or full-duplex operation
Double-buffered receive and transmit functions
Transmitter and receiver operations can be accomplished through interrupt-driven or polled algorithms with
status flags.
– Transmitter: TXRDY flag (transmitter-buffer register is ready to receive another character) and TX EMPTY
flag (transmitter-shift register is empty)
– Receiver: RXRDY flag (receiver-buffer register is ready to receive another character), BRKDT flag (break
condition occurred), and RX ERROR flag (monitoring four interrupt conditions)
Separate enable bits for transmitter and receiver interrupts (except BRKDT)
NRZ (non-return-to-zero) format
•
•
Note
All registers in this module are 8-bit registers that are connected to Peripheral Frame 2. When a
register is accessed, the register data is in the lower byte (7–0), and the upper byte (15–8) is read
as zeros. Writing to the upper byte has no effect.
Enhanced features:
•
•
Auto baud-detect hardware logic
4-level transmit/receive FIFO
Copyright © 2021 Texas Instruments Incorporated
112
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
The SCI port operation is configured and controlled by the registers listed in Table 8-27 and Table 8-28.
Table 8-27. SCI-A Registers
EALLOW
PROTECTED
NAME(1)
SCICCRA
ADDRESS
SIZE (×16)
DESCRIPTION
0x7050
0x7051
0x7052
0x7053
0x7054
0x7055
0x7056
0x7057
0x7059
0x705A
0x705B
0x705C
0x705F
1
1
1
1
1
1
1
1
1
1
1
1
1
No
No
No
No
No
No
No
No
No
No
No
No
No
SCI-A Communications Control Register
SCI-A Control Register 1
SCICTL1A
SCIHBAUDA
SCILBAUDA
SCICTL2A
SCI-A Baud Register, High Bits
SCI-A Baud Register, Low Bits
SCI-A Control Register 2
SCIRXSTA
SCIRXEMUA
SCIRXBUFA
SCITXBUFA
SCIFFTXA(2)
SCIFFRXA(2)
SCIFFCTA(2)
SCIPRIA
SCI-A Receive Status Register
SCI-A Receive Emulation Data Buffer Register
SCI-A Receive Data Buffer Register
SCI-A Transmit Data Buffer Register
SCI-A FIFO Transmit Register
SCI-A FIFO Receive Register
SCI-A FIFO Control Register
SCI-A Priority Control Register
(1) Registers in this table are mapped to Peripheral Frame 2 space. This space only allows 16-bit accesses. 32-bit accesses produce
undefined results.
(2) These registers are new registers for the FIFO mode.
Table 8-28. SCI-B Registers
NAME(1)
SCICCRB
ADDRESS
0x7750
0x7751
0x7752
0x7753
0x7754
0x7755
0x7756
0x7757
0x7759
0x775A
0x775B
0x775C
0x775F
SIZE (×16)
DESCRIPTION
SCI-B Communications Control Register
SCI-B Control Register 1
1
1
1
1
1
1
1
1
1
1
1
1
1
SCICTL1B
SCIHBAUDB
SCILBAUDB
SCICTL2B
SCI-B Baud Register, High Bits
SCI-B Baud Register, Low Bits
SCI-B Control Register 2
SCIRXSTB
SCIRXEMUB
SCIRXBUFB
SCITXBUFB
SCIFFTXB(2)
SCIFFRXB(2)
SCIFFCTB(2)
SCIPRIB
SCI-B Receive Status Register
SCI-B Receive Emulation Data Buffer Register
SCI-B Receive Data Buffer Register
SCI-B Transmit Data Buffer Register
SCI-B FIFO Transmit Register
SCI-B FIFO Receive Register
SCI-B FIFO Control Register
SCI-B Priority Control Register
(1) Registers in this table are mapped to Peripheral Frame 2 space. This space only allows 16-bit accesses. 32-bit accesses produce
undefined results.
(2) These registers are new registers for the FIFO mode.
Figure 8-37 shows the SCI module block diagram.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
113
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
TXENA
SCICTL1.1
Frame Format and Mode
Parity
SCITXD
SCITXD
TXSHF
Register
TXEMPTY
SCICTL2.6
Even/Odd
Enable
TXINTENA
SCICTL2.0
8
SCICCR.6 SCICCR.5
TXRDY
Transmitter Data
Buffer register
SCICTL2.7
SCITXBUF.7−0
8
TXWAKE
SCICTL1.3
TX FIFO_0
TX FIFO_1
−−−−−
TXINT
TX Interrupt
Logic
1
TX FIFO Interrupt
To CPU
TX FIFO_3
SCI TX Interrupt select logic
Auto baud detect logic
WUT
SCITXBUF.7−0
TX FIFO
SCIFFENA
SCIFFTX.14
RXENA
SCICTL1.0
SCIHBAUD. 15 − 8
SCIRXD
RXSHF
Register
Baud Rate
MSbyte
SCIRXD
Register
RXWAKE
LSPCLK
SCIRXST.1
SCILBAUD. 7 − 0
RXENA
SCICTL1.0
8
Baud Rate
LSbyte
RXBKINTENA
SCICTL2.1
Register
RXRDY
Receive Data
Buffer register
SCIRXST.6
SCIRXBUF.7−0
8
BRKDT
SCIRXST.5
RX FIFO_0
−−−−−
RX FIFO_2
RX FIFO_3
SCIRXBUF.7−0
RX Interrupt
Logic
RXINT
RX FIFO Interrupt
To CPU
RX FIFO
RXFFOVF
SCIFFRX.15
SCIRXST.7
RX Error
SCIRXST.5 – 2
BRKDT FE OE PE
RX Error
RXERRINTENA
SCICTL1.6
SCI RX Interrupt select logic
Figure 8-37. Serial Communications Interface (SCI) Module Block Diagram
Copyright © 2021 Texas Instruments Incorporated
114
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.6 Multichannel Buffered Serial Port (McBSP) Module
The McBSP module has the following features:
•
•
•
•
•
•
•
•
•
•
Compatible to McBSP in TMS320C28x/TMS320F28x DSP devices
Full-duplex communication
Double-buffered data registers that allow a continuous data stream
Independent framing and clocking for receive and transmit
External shift clock generation or an internal programmable frequency shift clock
A wide selection of data sizes including 8-, 12-, 16-, 20-, 24-, or 32-bits
8-bit data transfers with LSB or MSB first
Programmable polarity for both frame synchronization and data clocks
Highly programmable internal clock and frame generation
Direct interface to industry-standard CODECs, Analog Interface Chips (AICs), and other serially connected
analog-to-digital (A/D) and digital-to-analog (D/A) devices
Works with SPI-compatible devices
•
•
The following application interfaces can be supported on the McBSP:
– T1/E1 framers
– IOM-2 compliant devices
– AC97-compliant devices (the necessary multiphase frame synchronization capability is provided.)
– IIS-compliant devices
– SPI
•
McBSP clock rate,
CLKSRG
CLKG =
1+ CLKGDV
(
)
where CLKSRG source could be LSPCLK, CLKX, or CLKR. Serial port performance is limited by I/O buffer
switching speed. Internal prescalers must be adjusted such that the peripheral speed is less than the I/O
buffer speed limit.
Note
See Section 8.9 for maximum I/O pin toggling speed.
Note
On the 80-pin package, only the clock-stop mode (SPI) of the McBSP is supported.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
115
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Figure 8-38 shows the block diagram of the McBSP module.
TX
Interrupt
MXINT
Peripheral Write Bus
CPU
TX Interrupt Logic
To CPU
16
16
McBSP Transmit
Interrupt Select Logic
DXR2 Transmit Buffer
16
DXR1 Transmit Buffer
16
LSPCLK
MFSXx
MCLKXx
Compand Logic
XSR2
XSR1
MDXx
MDRx
CPU
DMA Bus
RSR1
16
RSR2
16
MCLKRx
Expand Logic
MFSRx
RBR2 Register
16
RBR1 Register
16
DRR2 Receive Buffer
DRR1 Receive Buffer
McBSP Receive
16
16
Interrupt Select Logic
RX
Interrupt
RX Interrupt Logic
MRINT
CPU
Peripheral Read Bus
To CPU
Figure 8-38. McBSP Module
Copyright © 2021 Texas Instruments Incorporated
116
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-29 provides a summary of the McBSP registers.
Table 8-29. McBSP Register Summary
McBSP-A
ADDRESS
NAME
TYPE
RESET VALUE
DESCRIPTION
Data Registers, Receive, Transmit
DRR2
DRR1
DXR2
DXR1
0x5000
0x5001
0x5002
0x5003
R
R
0x0000
0x0000
0x0000
0x0000
McBSP Data Receive Register 2
McBSP Data Receive Register 1
W
W
McBSP Data Transmit Register 2
McBSP Data Transmit Register 1
McBSP Control Registers
SPCR2
SPCR1
RCR2
0x5004
0x5005
0x5006
0x5007
0x5008
0x5009
0x500A
0x500B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
McBSP Serial Port Control Register 2
McBSP Serial Port Control Register 1
McBSP Receive Control Register 2
McBSP Receive Control Register 1
McBSP Transmit Control Register 2
McBSP Transmit Control Register 1
McBSP Sample Rate Generator Register 2
McBSP Sample Rate Generator Register 1
RCR1
XCR2
XCR1
SRGR2
SRGR1
Multichannel Control Registers
McBSP Multichannel Register 2
MCR2
0x500C
0x500D
0x500E
0x500F
0x5010
0x5011
0x5012
0x5013
0x5014
0x5015
0x5016
0x5017
0x5018
0x5019
0x501A
0x501B
0x501C
0x501D
0x501E
0x5023
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
MCR1
McBSP Multichannel Register 1
RCERA
RCERB
XCERA
XCERB
PCR
McBSP Receive Channel Enable Register Partition A
McBSP Receive Channel Enable Register Partition B
McBSP Transmit Channel Enable Register Partition A
McBSP Transmit Channel Enable Register Partition B
McBSP Pin Control Register
RCERC
RCERD
XCERC
XCERD
RCERE
RCERF
XCERE
XCERF
RCERG
RCERH
XCERG
XCERH
MFFINT
McBSP Receive Channel Enable Register Partition C
McBSP Receive Channel Enable Register Partition D
McBSP Transmit Channel Enable Register Partition C
McBSP Transmit Channel Enable Register Partition D
McBSP Receive Channel Enable Register Partition E
McBSP Receive Channel Enable Register Partition F
McBSP Transmit Channel Enable Register Partition E
McBSP Transmit Channel Enable Register Partition F
McBSP Receive Channel Enable Register Partition G
McBSP Receive Channel Enable Register Partition H
McBSP Transmit Channel Enable Register Partition G
McBSP Transmit Channel Enable Register Partition H
McBSP Interrupt Enable Register
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
117
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.6.1 McBSP Electrical Data/Timing
8.9.6.1.1 McBSP Transmit and Receive Timing
8.9.6.1.1.1 McBSP Timing Requirements
NO.(1)
MIN
MAX
UNIT
(2)
1
kHz
MHz
ns
McBSP module clock (CLKG, CLKX, CLKR) range
McBSP module cycle time (CLKG, CLKX, CLKR) range
20(3) (4)
50(4)
1
ms
ns
M11 tc(CKRX)
M12 tw(CKRX)
M13 tr(CKRX)
M14 tf(CKRX)
Cycle time, CLKR/X
CLKR/X ext
CLKR/X ext
CLKR/X ext
CLKR/X ext
CLKR int
CLKR ext
CLKR int
CLKR ext
CLKR int
CLKR ext
CLKR int
CLKR ext
CLKX int
2P
Pulse duration, CLKR/X high or CLKR/X low
Rise time, CLKR/X
P – 7
ns
7
7
ns
Fall time, CLKR/X
ns
18
2
M15 tsu(FRH-CKRL)
M16 th(CKRL-FRH)
M17 tsu(DRV-CKRL)
M18 th(CKRL-DRV)
M19 tsu(FXH-CKXL)
M20 th(CKXL-FXH)
Setup time, external FSR high before CLKR low
Hold time, external FSR high after CLKR low
Setup time, DR valid before CLKR low
ns
ns
ns
ns
ns
ns
0
6
18
2
0
Hold time, DR valid after CLKR low
6
18
2
Setup time, external FSX high before CLKX low
Hold time, external FSX high after CLKX low
CLKX ext
CLKX int
0
CLKX ext
6
(1) Polarity bits CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that
signal are also inverted.
(2) 2P = 1/CLKG in ns. CLKG is the output of sample rate generator mux. CLKG = CLKSRG/(1 + CLKGDV). CLKSRG can be LSPCLK,
CLKX, CLKR as source. CLKSRG ≤ (SYSCLKOUT/2). McBSP performance is limited by I/O buffer switching speed.
(3) Internal clock prescalers must be adjusted such that the McBSP clock (CLKG, CLKX, CLKR) speeds are not greater than the I/O buffer
speed limit (20 MHz).
(4) Maximum McBSP module clock frequency decreases to 10 MHz for internal CLKR.
Copyright © 2021 Texas Instruments Incorporated
118
Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.6.1.1.2 McBSP Switching Characteristics
over recommended operating conditions (unless otherwise noted)(1) (2)
NO.
M1
M2
M3
PARAMETER
MIN
MAX UNIT
tc(CKRX)
Cycle time, CLKR/X
CLKR/X int
CLKR/X int
CLKR/X int
CLKR int
CLKR ext
CLKX int
CLKX ext
CLKX int
CLKX ext
CLKX int
CLKX ext
CLKX int
CLKX ext
CLKX int
2P
ns
tw(CKRXH)
tw(CKRXL)
Pulse duration, CLKR/X high
Pulse duration, CLKR/X low
D – 5(3)
D + 5(3)
ns
ns
C – 5(3)
C + 5(3)
0
3
0
3
4
27
4
M4
M5
M6
td(CKRH-FRV)
td(CKXH-FXV)
tdis(CKXH-DXHZ)
Delay time, CLKR high to internal FSR valid
Delay time, CLKX high to internal FSX valid
ns
ns
ns
27
8
Disable time, CLKX high to DX high impedance
following last data bit
14
9
Delay time, CLKX high to DX valid.
This applies to all bits except the first bit transmitted.
28
8
Delay time, CLKX high to DX valid
DXENA = 0
M7
td(CKXH-DXV)
ns
ns
14
P + 8
Only applies to first bit transmitted when
in Data Delay 1 or 2 (XDATDLY=01b or DXENA = 1
10b) modes
CLKX ext
P + 14
CLKX int
CLKX ext
CLKX int
0
6
Enable time, CLKX high to DX driven
Only applies to first bit transmitted when
in Data Delay 1 or 2 (XDATDLY=01b or DXENA = 1
10b) modes
DXENA = 0
M8
M9
ten(CKXH-DX)
P
CLKX ext
P + 6
FSX int
FSX ext
FSX int
FSX ext
FSX int
FSX ext
FSX int
FSX ext
8
14
Delay time, FSX high to DX valid
DXENA = 0
DXENA = 1
DXENA = 0
DXENA = 1
td(FXH-DXV)
ns
ns
P + 8
P + 14
Only applies to first bit transmitted when
in Data Delay 0 (XDATDLY=00b) mode.
0
6
Enable time, FSX high to DX driven
M10 ten(FXH-DX)
P
Only applies to first bit transmitted when
in Data Delay 0 (XDATDLY=00b) mode
P + 6
(1) Polarity bits CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that
signal are also inverted.
(2) 2P = 1/CLKG in ns.
(3) C = CLKRX low pulse width = P
D = CLKRX high pulse width = P
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
119
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
M1, M11
M2, M12
M3, M12
M13
CLKR
M4
M4
M14
FSR (int)
M15
M16
FSR (ext)
M18
M17
DR
(RDATDLY=00b)
Bit (n−1)
M17
(n−2)
(n−3)
(n−2)
(n−4)
M18
DR
(RDATDLY=01b)
Bit (n−1)
(n−3)
(n−2)
M17
M18
DR
(RDATDLY=10b)
Bit (n−1)
Figure 8-39. McBSP Receive Timing
M1, M11
M2, M12
M13
M14
M3, M12
CLKX
FSX (int)
FSX (ext)
M5
M5
M19
M20
M9
M7
M10
Bit 0
DX
(XDATDLY=00b)
Bit (n−1)
(n−2)
(n−3)
(n−2)
(n−4)
(n−3)
(n−2)
M7
M8
DX
(XDATDLY=01b)
Bit (n−1)
M8
Bit 0
M6
M7
DX
(XDATDLY=10b)
Bit 0
Bit (n−1)
Figure 8-40. McBSP Transmit Timing
Copyright © 2021 Texas Instruments Incorporated
120 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.6.1.2 McBSP as SPI Master or Slave Timing
8.9.6.1.2.1 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0)
MASTER
SLAVE
MIN MAX
NO.(1)
UNIT
MIN
30
1
MAX
M30 tsu(DRV-CKXL)
M31 th(CKXL-DRV)
M32 tsu(BFXL-CKXH)
M33 tc(CKX)
Setup time, DR valid before CLKX low
Hold time, DR valid after CLKX low
Setup time, FSX low before CLKX high
Cycle time, CLKX
8P – 10
ns
ns
ns
ns
8P – 10
8P + 10
16P
2P(2)
(1) For all SPI slave modes, CLKX has to be a minimum of 8 CLKG cycles. Furthermore, CLKG should be LSPCLK/2 by setting CLKSM =
CLKGDV = 1.
(2) 2P = 1/CLKG
8.9.6.1.2.2 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0)
over recommended operating conditions (unless otherwise noted)
MASTER
MIN
SLAVE
MIN
NO.
PARAMETER
UNIT
MAX
MAX
M24
M25
M26
th(CKXL-FXL)
td(FXL-CKXH)
td(CKXH-DXV)
Hold time, FSX low after CLKX low
Delay time, FSX low to CLKX high
Delay time, CLKX high to DX valid
2P(1)
ns
ns
ns
P
–2
0
3P + 6
5P + 20
Disable time, DX high impedance following
last data bit from FSX high
M28
M29
tdis(FXH-DXHZ)
td(FXL-DXV)
6
6
6P + 6
4P + 6
ns
ns
Delay time, FSX low to DX valid
(1) 2P = 1/CLKG
M33
M32
MSB
LSB
CLKX
M25
M26
M24
FSX
M28
M29
DX
DR
Bit 0
Bit(n-1)
(n-2)
(n-3)
(n-4)
M30
M31
Bit 0
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 8-41. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 121
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
www.ti.com
UNIT
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
8.9.6.1.2.3 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0)
MASTER
SLAVE
MIN MAX
NO.(1)
MIN
30
1
MAX
M39 tsu(DRV-CKXH)
M40 th(CKXH-DRV)
M41 tsu(FXL-CKXH)
M42 tc(CKX)
Setup time, DR valid before CLKX high
Hold time, DR valid after CLKX high
Setup time, FSX low before CLKX high
Cycle time, CLKX
8P – 10
ns
ns
ns
ns
8P – 10
16P + 10
16P
2P(2)
(1) For all SPI slave modes, CLKX has to be a minimum of 8 CLKG cycles. Furthermore, CLKG should be LSPCLK/2 by setting CLKSM =
CLKGDV = 1.
(2) 2P = 1/CLKG
8.9.6.1.2.4 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0)
over recommended operating conditions (unless otherwise noted)
MASTER
MIN
SLAVE
MIN
NO.
PARAMETER
UNIT
MAX
MAX
M34 th(CKXL-FXL)
M35 td(FXL-CKXH)
M36 td(CKXL-DXV)
Hold time, FSX low after CLKX low
Delay time, FSX low to CLKX high
Delay time, CLKX low to DX valid
P
2P(1)
–2
ns
ns
ns
0
3P + 6 5P + 20
7P + 6
Disable time, DX high impedance following last data bit
from CLKX low
M37 tdis(CKXL-DXHZ)
M38 td(FXL-DXV)
P + 6
6
ns
ns
Delay time, FSX low to DX valid
4P + 6
(1) 2P = 1/CLKG
M42
MSB
LSB
M41
CLKX
M36
M35
M34
FSX
M37
M38
DX
DR
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
M40
(n-2)
(n-3)
(n-4)
M39
Bit 0
(n-3)
(n-4)
Figure 8-42. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
Copyright © 2021 Texas Instruments Incorporated
122 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.6.1.2.5 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1)
MASTER
SLAVE
MIN MAX
NO.(1)
UNIT
MIN
30
1
MAX
M49 tsu(DRV-CKXH)
M50 th(CKXH-DRV)
M51 tsu(FXL-CKXL)
M52 tc(CKX)
Setup time, DR valid before CLKX high
Hold time, DR valid after CLKX high
Setup time, FSX low before CLKX low
Cycle time, CLKX
8P – 10
ns
ns
ns
ns
8P – 10
8P + 10
16P
2P(2)
(1) For all SPI slave modes, CLKX has to be a minimum of 8 CLKG cycles. Furthermore, CLKG should be LSPCLK/2 by setting CLKSM =
CLKGDV = 1.
(2) 2P = 1/CLKG
8.9.6.1.2.6 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)
over recommended operating conditions (unless otherwise noted)
MASTER
SLAVE
MIN MAX
NO.
PARAMETER
UNIT
MIN
2P(1)
P
MAX
M43 th(CKXH-FXL)
M44 td(FXL-CKXL)
M45 td(CKXL-DXV)
Hold time, FSX low after CLKX high
Delay time, FSX low to CLKX low
Delay time, CLKX low to DX valid
ns
ns
ns
–2
0
3P + 6 5P + 20
6P + 6
Disable time, DX high impedance following last data bit from
FSX high
M47 tdis(FXH-DXHZ)
M48 td(FXL-DXV)
6
6
ns
ns
Delay time, FSX low to DX valid
4P + 6
(1) 2P = 1/CLKG
M52
M51
MSB
LSB
CLKX
M45
M43
M44
FSX
M48
M47
DX
DR
Bit 0
Bit(n-1)
Bit(n-1)
(n-2)
(n-3)
(n-4)
(n-4)
M49
M50
(n-2)
Bit 0
(n-3)
Figure 8-43. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 123
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
www.ti.com
UNIT
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
8.9.6.1.2.7 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1)
MASTER
SLAVE
MIN MAX
NO.(1)
MIN
30
1
MAX
M58 tsu(DRV-CKXL)
M59 th(CKXL-DRV)
M60 tsu(FXL-CKXL)
M61 tc(CKX)
Setup time, DR valid before CLKX low
Hold time, DR valid after CLKX low
Setup time, FSX low before CLKX low
Cycle time, CLKX
8P – 10
ns
ns
ns
ns
8P – 10
16P + 10
16P
2P(2)
(1) For all SPI slave modes, CLKX has to be a minimum of 8 CLKG cycles. Furthermore, CLKG should be LSPCLK/2 by setting CLKSM =
CLKGDV = 1.
(2) 2P = 1/CLKG
8.9.6.1.2.8 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1)
over recommended operating conditions (unless otherwise noted)(1)
MASTER
MIN
SLAVE
MIN
NO.
PARAMETER
UNIT
MAX
MAX
M53 th(CKXH-FXL)
M54 td(FXL-CKXL)
M55 td(CKXH-DXV)
Hold time, FSX low after CLKX high
Delay time, FSX low to CLKX low
Delay time, CLKX high to DX valid
P
ns
ns
ns
2P(1)
–2
0
3P + 6
5P + 20
Disable time, DX high impedance following last data
bit from CLKX high
M56 tdis(CKXH-DXHZ)
M57 td(FXL-DXV)
P + 6
6
7P + 6
4P + 6
ns
ns
Delay time, FSX low to DX valid
(1) 2P = 1/CLKG
M61
M60
MSB
LSB
CLKX
M53
M54
FSX
M56
M55
M57
DX
DR
Bit 0
Bit(n-1)
(n-2)
(n-3)
(n-4)
(n-4)
M58
M59
Bit 0
Bit(n-1)
(n-2)
(n-3)
Figure 8-44. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
Copyright © 2021 Texas Instruments Incorporated
124 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.7 Enhanced Controller Area Network (eCAN) Module
The CAN module (eCAN-A) has the following features:
•
•
•
Fully compliant with CAN protocol, version 2.0B
Supports data rates up to 1 Mbps
Thirty-two mailboxes, each with the following properties:
– Configurable as receive or transmit
– Configurable with standard or extended identifier
– Has a programmable receive mask
– Supports data and remote frame
– Composed of 0 to 8 bytes of data
– Uses a 32-bit timestamp on receive and transmit message
– Protects against reception of new message
– Holds the dynamically programmable priority of transmit message
– Employs a programmable interrupt scheme with two interrupt levels
– Employs a programmable alarm on transmission or reception time-out
Low-power mode
Programmable wake-up on bus activity
Automatic reply to a remote request message
Automatic retransmission of a frame in case of loss of arbitration or error
32-bit local network time counter synchronized by a specific message (communication in conjunction with
mailbox 16)
•
•
•
•
•
•
Self-test mode
– Operates in a loopback mode receiving its own message. A "dummy" acknowledge is provided, thereby
eliminating the need for another node to provide the acknowledge bit.
Note
For a SYSCLKOUT of 90 MHz, the smallest bit rate possible is 6.25 kbps.
The F2806x CAN has passed the conformance test per ISO/DIS 16845. Contact TI for test report and
exceptions.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 125
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
eCAN0INT
eCAN1INT
Controls Address
Data
32
Enhanced CAN Controller
Message Controller
Mailbox RAM
(512 Bytes)
Memory Management
Unit
eCAN Memory
(512 Bytes)
Registers and
CPU Interface,
Receive Control Unit,
Timer Management Unit
32-Message Mailbox
of 4 ´ 32-Bit Words
Message Objects Control
32
32
32
eCAN Protocol Kernel
Receive Buffer
Transmit Buffer
Control Buffer
Status Buffer
SN65HVD23x
3.3-V CAN Transceiver
CAN Bus
Figure 8-45. eCAN Block Diagram and Interface Circuit
Table 8-30. 3.3-V eCAN Transceivers
SUPPLY
VOLTAGE
LOW-POWER
MODE
SLOPE
CONTROL
PART NUMBER
VREF
OTHER
TA
–40°C to 85°C
SN65HVD230
SN65HVD230Q
SN65HVD231
SN65HVD231Q
SN65HVD232
SN65HVD232Q
SN65HVD233
SN65HVD234
SN65HVD235
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
Standby
Standby
Sleep
Adjustable
Adjustable
Adjustable
Adjustable
None
Yes
Yes
–
–
–40°C to 125°C
–40°C to 85°C
–40°C to 125°C
–40°C to 85°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Yes
–
Sleep
Yes
–
None
None
None
None
None
None
–
None
None
–
Standby
Standby and Sleep
Standby
Adjustable
Adjustable
Adjustable
Diagnostic Loopback
–
Autobaud Loopback
Built-in Isolation
Low Prop Delay
ISO1050
3–5.5 V
None
None
None
Thermal Shutdown
Fail-safe Operation
Dominant Time-Out
–55°C to 105°C
Copyright © 2021 Texas Instruments Incorporated
126 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
eCAN-A Control and Status Registers
Mailbox Enable - CANME
Mailbox Direction - CANMD
Transmission Request Set - CANTRS
Transmission Request Reset - CANTRR
Transmission Acknowledge - CANTA
eCAN-A Memory (512 Bytes)
Control and Status Registers
Abort Acknowledge - CANAA
Received Message Pending - CANRMP
Received Message Lost - CANRML
Remote Frame Pending - CANRFP
Global Acceptance Mask - CANGAM
6000h
603Fh
6040h
Local Acceptance Masks (LAM)
(32 ´ 32-Bit RAM)
607Fh
6080h
Master Control - CANMC
Message Object Timestamps (MOTS)
(32 ´ 32-Bit RAM)
Bit-Timing Configuration - CANBTC
60BFh
60C0h
Error and Status - CANES
Message Object Time-Out (MOTO)
(32 ´ 32-Bit RAM)
Transmit Error Counter - CANTEC
Receive Error Counter - CANREC
Global Interrupt Flag 0 - CANGIF0
Global Interrupt Mask - CANGIM
Global Interrupt Flag 1 - CANGIF1
Mailbox Interrupt Mask - CANMIM
Mailbox Interrupt Level - CANMIL
60FFh
eCAN-A Memory RAM (512 Bytes)
6100h-6107h
6108h-610Fh
6110h-6117h
6118h-611Fh
6120h-6127h
Mailbox 0
Mailbox 1
Mailbox 2
Mailbox 3
Mailbox 4
Overwrite Protection Control - CANOPC
TX I/O Control - CANTIOC
RX I/O Control - CANRIOC
Timestamp Counter - CANTSC
Time-Out Control - CANTOC
Time-Out Status - CANTOS
61E0h-61E7h
61E8h-61EFh
61F0h-61F7h
61F8h-61FFh
Mailbox 28
Mailbox 29
Mailbox 30
Mailbox 31
Reserved
Message Mailbox (16 Bytes)
Message Identifier - MSGID
Message Control - MSGCTRL
Message Data Low - MDL
Message Data High - MDH
61E8h-61E9h
61EAh-61EBh
61ECh-61EDh
61EEh-61EFh
Figure 8-46. eCAN-A Memory Map
Note
If the eCAN module is not used in an application, the RAM available (LAM, MOTS, MOTO, and
mailbox RAM) can be used as general-purpose RAM. The CAN module clock should be enabled for
this.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 127
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
The CAN registers listed in Table 8-31 are used by the CPU to configure and control the CAN controller and the
message objects. eCAN control registers only support 32-bit read/write operations. Mailbox RAM can be
accessed as 16 bits or 32 bits. All 32-bit accesses are aligned to an even boundary.
Table 8-31. CAN Registers
eCAN-A
REGISTER NAME(1)
SIZE (×32)
DESCRIPTION
ADDRESS
0x6000
0x6002
0x6004
0x6006
0x6008
0x600A
0x600C
0x600E
0x6010
0x6012
0x6014
0x6016
0x6018
0x601A
0x601C
0x601E
0x6020
0x6022
0x6024
0x6026
0x6028
0x602A
0x602C
0x602E
0x6030
0x6032
CANME
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Mailbox enable
CANMD
Mailbox direction
CANTRS
CANTRR
CANTA
Transmit request set
Transmit request reset
Transmission acknowledge
Abort acknowledge
Receive message pending
Receive message lost
Remote frame pending
Global acceptance mask
Master control
CANAA
CANRMP
CANRML
CANRFP
CANGAM
CANMC
CANBTC
CANES
Bit-timing configuration
Error and status
CANTEC
CANREC
CANGIF0
CANGIM
CANGIF1
CANMIM
CANMIL
CANOPC
CANTIOC
CANRIOC
CANTSC
CANTOC
CANTOS
Transmit error counter
Receive error counter
Global interrupt flag 0
Global interrupt mask
Global interrupt flag 1
Mailbox interrupt mask
Mailbox interrupt level
Overwrite protection control
TX I/O control
RX I/O control
Timestamp counter (Reserved in SCC mode)
Time-out control (Reserved in SCC mode)
Time-out status (Reserved in SCC mode)
(1) These registers are mapped to Peripheral Frame 1.
Copyright © 2021 Texas Instruments Incorporated
128 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.8 Inter-Integrated Circuit (I2C)
The device contains one I2C Serial Port. Figure 8-47 shows how the I2C peripheral module interfaces within the
device.
The I2C module has the following features:
•
Compliance with the Philips Semiconductors I2C-bus specification (version 2.1):
– Support for 1-bit to 8-bit format transfers
– 7-bit and 10-bit addressing modes
– General call
– START byte mode
– Support for multiple master-transmitters and slave-receivers
– Support for multiple slave-transmitters and master-receivers
– Combined master transmit/receive and receive/transmit mode
– Data transfer rate of from 10 kbps up to 400 kbps (I2C Fast-mode rate)
One 4-word receive FIFO and one 4-word transmit FIFO
One interrupt that can be used by the CPU. This interrupt can be generated as a result of one of the following
conditions:
•
•
– Transmit-data ready
– Receive-data ready
– Register-access ready
– No-acknowledgment received
– Arbitration lost
– Stop condition detected
– Addressed as slave
•
•
•
An additional interrupt that can be used by the CPU when in FIFO mode
Module enable/disable capability
Free data format mode
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 129
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
I2C Module
I2CXSR
I2CDXR
TX FIFO
RX FIFO
FIFO Interrupt to
CPU/PIE
SDA
Peripheral Bus
I2CRSR
I2CDRR
Control/Status
Registers
CPU
Clock
Synchronizer
SCL
Prescaler
Noise Filters
Arbitrator
Interrupt to
CPU/PIE
I2C INT
A. The I2C registers are accessed at the SYSCLKOUT rate. The internal timing and signal waveforms of the I2C port are also at the
SYSCLKOUT rate.
B. The clock enable bit (I2CAENCLK) in the PCLKCRO register turns off the clock to the I2C port for low-power operation. Upon reset,
I2CAENCLK is clear, which indicates the peripheral internal clocks are off.
Figure 8-47. I2C Peripheral Module Interfaces
The registers in Table 8-32 configure and control the I2C port operation.
Table 8-32. I2C-A Registers
EALLOW
PROTECTED
NAME
ADDRESS
DESCRIPTION
I2C own address register
I2COAR
I2CIER
0x7900
0x7901
0x7902
0x7903
0x7904
0x7905
0x7906
0x7907
0x7908
0x7909
0x790A
0x790C
0x7920
0x7921
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
I2C interrupt enable register
I2C status register
I2CSTR
I2CCLKL
I2CCLKH
I2CCNT
I2CDRR
I2CSAR
I2CDXR
I2CMDR
I2CISRC
I2CPSC
I2CFFTX
I2CFFRX
I2CRSR
I2C clock low-time divider register
I2C clock high-time divider register
I2C data count register
I2C data receive register
I2C slave address register
I2C data transmit register
I2C mode register
I2C interrupt source register
I2C prescaler register
I2C FIFO transmit register
I2C FIFO receive register
I2C receive shift register (not accessible to the CPU)
Copyright © 2021 Texas Instruments Incorporated
130 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-32. I2C-A Registers (continued)
EALLOW
PROTECTED
NAME
ADDRESS
DESCRIPTION
I2CXSR
–
No
I2C transmit shift register (not accessible to the CPU)
8.9.8.1 I2C Electrical Data/Timing
Section 8.9.8.1.1 shows the I2C timing requirements. Section 8.9.8.1.2 shows the I2C switching characteristics.
8.9.8.1.1 I2C Timing Requirements
MIN
MAX UNIT
Hold time, START condition, SCL fall delay
after SDA fall
th(SDA-SCL)START
tsu(SCL-SDA)START
0.6
µs
Setup time, Repeated START, SCL rise
before SDA fall delay
0.6
µs
th(SCL-DAT)
tsu(DAT-SCL)
tr(SDA)
Hold time, data after SCL fall
Setup time, data before SCL rise
Rise time, SDA
0
100
20
µs
ns
Input tolerance
Input tolerance
Input tolerance
Input tolerance
300
300
300
300
ns
ns
ns
ns
tr(SCL)
Rise time, SCL
20
tf(SDA)
Fall time, SDA
11.4
11.4
tf(SCL)
Fall time, SCL
Setup time, STOP condition, SCL rise before
SDA rise delay
tsu(SCL-SDA)STOP
0.6
µs
8.9.8.1.2 I2C Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
I2C clock module frequency is from 7 MHz to
12 MHz and I2C prescaler and clock divider
registers are configured appropriately.
fSCL
SCL clock frequency
400
kHz
Vil
Low level input voltage
High level input voltage
Input hysteresis
0.3 VDDIO
V
V
V
V
Vih
Vhys
Vol
0.7 VDDIO
0.05 VDDIO
0
Low level output voltage
3-mA sink current
0.4
I2C clock module frequency is from 7 MHz to
12 MHz and I2C prescaler and clock divider
registers are configured appropriately.
tLOW Low period of SCL clock
tHIGH High period of SCL clock
1.3
μs
I2C clock module frequency is from 7 MHz to
12 MHz and I2C prescaler and clock divider
registers are configured appropriately.
0.6
μs
Input current with an input voltage from
0.1 VDDIO to 0.9 VDDIO MAX
lI
–10
10
μA
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 131
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.9 Enhanced Pulse Width Modulator (ePWM) Modules (ePWM1 to ePWM8)
The devices contain up to eight enhanced PWM (ePWM) modules. Figure 8-48 shows a block diagram of
multiple ePWM modules. Figure 8-49 shows the signal interconnections with the ePWM.
Table 8-33 and Table 8-34 show the complete ePWM register set per module.
EPWMSYNCI
EPWM1SYNCI
EPWM1B
EPWM1TZINT
EPWM1
Module
TZ1 to TZ3
EPWM1INT
EQEP1ERR(A)
EPWM2TZINT
TZ4
PIE
EPWM2INT
CLOCKFAIL
TZ5
EPWMxTZINT
EMUSTOP
TZ6
EPWMxINT
EPWM1ENCLK
TBCLKSYNC
eCAPI
EPWM1SYNCO
EPWM2SYNCI
EPWM1SYNCO
TZ1 to TZ3
COMPOUT1
COMPOUT2
EPWM2B
EPWM2
Module
EQEP1ERR(A)
CLOCKFAIL
EMUSTOP
COMP
EPWM1A
EPWM2A
TZ4
TZ5
TZ6
H
R
P
W
M
EPWM2ENCLK
TBCLKSYNC
EPWMxA
G
P
I
EPWM2SYNCO
O
M
U
X
SOCA1
SOCB1
SOCA2
SOCB2
SOCAx
SOCBx
ADC
EPWMxB
EPWMxSYNCI
TZ1 to TZ3
EPWMx
Module
EQEP1ERR(A)
CLOCKFAIL
EMUSTOP
EQEP1ERR
TZ4
TZ5
TZ6
eQEP1
EPWMxENCLK
TBCLKSYNC
System Control
C28x CPU
SOCA1
SOCA2
SPCAx
ADCSOCAO
ADCSOCBO
Pulse Stretch
(32 SYSCLKOUT Cycles, Active-Low Output)
SOCB1
SOCB2
SPCBx
Pulse Stretch
(32 SYSCLKOUT Cycles, Active-Low Output)
A. This signal exists only on devices with an eQEP1 module.
Figure 8-48. ePWM
Copyright © 2021 Texas Instruments Incorporated
132 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
www.ti.com
NAME
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
Table 8-33. ePWM1–ePWM4 Control and Status Registers
SIZE (×16)/
#SHADOW
ePWM1
ePWM2
ePWM3
ePWM4
DESCRIPTION
TBCTL
0x6800
0x6801
0x6802
0x6803
0x6804
0x6805
0x6806
0x6807
0x6808
0x6809
0x680A
0x680B
0x680C
0x680D
0x6840
0x6841
0x6842
0x6843
0x6844
0x6845
0x6846
0x6847
0x6848
0x6849
0x684A
0x684B
0x684C
0x684D
0x6880
0x6881
0x6882
0x6883
0x6884
0x6885
0x6886
0x6887
0x6888
0x6889
0x688A
0x688B
0x688C
0x688D
0x68C0
0x68C1
0x68C2
0x68C3
0x68C4
0x68C5
0x68C6
0x68C7
0x68C8
0x68C9
0x68CA
0x68CB
0x68CC
0x68CD
1/0
Time Base Control Register
TBSTS
1/0
Time Base Status Register
TBPHSHR
TBPHS
1/0
Time Base Phase HRPWM Register
Time Base Phase Register
1/0
TBCTR
1/0
Time Base Counter Register
TBPRD
1/1
Time Base Period Register Set
TBPRDHR
CMPCTL
CMPAHR
CMPA
1/1
Time Base Period High-Resolution Register(1)
Counter Compare Control Register
Time Base Compare A HRPWM Register
Counter Compare A Register Set
Counter Compare B Register Set
Action Qualifier Control Register For Output A
Action Qualifier Control Register For Output B
Action Qualifier Software Force Register
1/0
1/1
1/1
CMPB
1/1
AQCTLA
AQCTLB
AQSFRC
1/0
1/0
1/0
Action Qualifier Continuous S/W Force
Register Set
AQCSFRC
DBCTL
0x680E
0x680F
0x6810
0x684E
0x684F
0x6850
0x688E
0x688F
0x6890
0x68CE
0x68CF
0x68D0
1/1
1/1
1/0
Dead-Band Generator Control Register
Dead-Band Generator Rising Edge Delay
Count Register
DBRED
Dead-Band Generator Falling Edge Delay
Count Register
DBFED
0x6811
0x6851
0x6891
0x68D1
1/0
TZSEL
0x6812
0x6813
0x6814
0x6815
0x6816
0x6817
0x6818
0x6819
0x681A
0x681B
0x681C
0x681D
0x681E
0x6820
0x6826
0x6828
0x682A
0x682B
0x682C
0x682D
0x6830
0x6831
0x6832
0x6833
0x6834
0x6852
0x6853
0x6854
0x6855
0x6856
0x6857
0x6858
0x6859
0x685A
0x685B
0x685C
0x685D
0x685E
0x6860
-
0x6892
0x6893
0x6894
0x6895
0x6896
0x6897
0x6898
0x6899
0x689A
0x689B
0x689C
0x689D
0x689E
0x68A0
-
0x68D2
0x68D3
0x68D4
0x68D5
0x68D6
0x68D7
0x68D8
0x68D9
0x68DA
0x68DB
0x68DC
0x68DD
0x68DE
0x68E0
-
1/0
1/0
Trip Zone Select Register(1)
TZDCSEL
TZCTL
Trip Zone Digital Compare Register
Trip Zone Control Register(1)
1/0
TZEINT
1/0
Trip Zone Enable Interrupt Register(1)
Trip Zone Flag Register (1)
TZFLG
1/0
TZCLR
1/0
Trip Zone Clear Register(1)
TZFRC
1/0
Trip Zone Force Register(1)
ETSEL
1/0
Event Trigger Selection Register
Event Trigger Prescale Register
Event Trigger Flag Register
ETPS
1/0
ETFLG
1/0
ETCLR
1/0
Event Trigger Clear Register
ETFRC
1/0
Event Trigger Force Register
PCCTL
1/0
PWM Chopper Control Register
HRPWM Configuration Register(1)
HRPWM MEP Step Register
HRCNFG
HRMSTEP
HRPCTL
TBPRDHRM
TBPRDM
CMPAHRM
CMPAM
DCTRIPSEL
DCACTL
DCBCTL
DCFCTL
DCCAPCT
1/0
1/0
0x6868
0x686A
0x686B
0x686C
0x686D
0x6870
0x6871
0x6872
0x6873
0x6874
0x68A8
0x68AA
0x68AB
0x68AC
0x68AD
0x68B0
0x68B1
0x68B2
0x68B3
0x68B4
0x68E8
0x68EA
0x68EB
0x68EC
0x68ED
0x68F0
0x68F1
0x68F2
0x68F3
0x68F4
1/0
High-resolution Period Control Register(1)
Time Base Period HRPWM Register Mirror
Time Base Period Register Mirror
Compare A HRPWM Register Mirror
Compare A Register Mirror
1/W(2)
1/W(2)
1/W(2)
1/W(2)
1/0
Digital Compare Trip Select Register (1)
Digital Compare A Control Register(1)
Digital Compare B Control Register(1)
Digital Compare Filter Control Register(1)
Digital Compare Capture Control Register(1)
1/0
1/0
1/0
1/0
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 133
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-33. ePWM1–ePWM4 Control and Status Registers (continued)
SIZE (×16)/
#SHADOW
NAME
ePWM1
0x6835
0x6836
0x6837
0x6838
0x6839
ePWM2
0x6875
0x6876
0x6877
0x6878
0x6879
ePWM3
0x68B5
0x68B6
0x68B7
0x68B8
0x68B9
ePWM4
0x68F5
0x68F6
0x68F7
0x68F8
0x68F9
DESCRIPTION
DCFOFFSET
1/1
Digital Compare Filter Offset Register
Digital Compare Filter Offset Counter Register
Digital Compare Filter Window Register
DCFOFFSETCN
T
1/0
1/0
1/0
1/1
DCFWINDOW
DCFWINDOWCN
T
Digital Compare Filter Window Counter
Register
DCCAP
Digital Compare Counter Capture Register
(1) Registers that are EALLOW protected.
(2) W = Write to shadow register
Copyright © 2021 Texas Instruments Incorporated
134 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-34. ePWM5–ePWM8 Control and Status Registers
SIZE (×16)/
#SHADOW
NAME
ePWM5
ePWM6
ePWM7
ePWM8
DESCRIPTION
TBCTL
0x6900
0x6901
0x6902
0x6903
0x6904
0x6905
0x6940
0x6941
0x6942
0x6943
0x6944
0x6945
0x6980
0x6981
0x6982
0x6983
0x6984
0x6985
0x69C0
0x69C1
0x69C2
0x69C3
0x69C4
0x69C5
1/0
1/0
1/0
1/0
1/0
1/1
Time Base Control Register
Time Base Status Register
Time Base Phase HRPWM Register
Time Base Phase Register
Time Base Counter Register
Time Base Period Register Set
TBSTS
TBPHSHR
TBPHS
TBCTR
TBPRD
Time Base Period High-Resolution
Register(1)
TBPRDHR
0x6906
0x6946
0x6986
0x69C6
1/1
CMPCTL
CMPAHR
CMPA
0x6907
0x6908
0x6909
0x690A
0x6947
0x6948
0x6949
0x694A
0x6987
0x6988
0x6989
0x698A
0x69C7
0x69C8
0x69C9
0x69CA
1/0
1/1
1/1
1/1
Counter Compare Control Register
Time Base Compare A HRPWM Register
Counter Compare A Register Set
Counter Compare B Register Set
CMPB
Action Qualifier Control Register For
Output A
AQCTLA
0x690B
0x694B
0x698B
0x69CB
1/0
Action Qualifier Control Register For
Output B
AQCTLB
AQSFRC
AQCSFRC
DBCTL
0x690C
0x690D
0x690E
0x690F
0x6910
0x694C
0x694D
0x694E
0x694F
0x6950
0x698C
0x698D
0x698E
0x698F
0x6990
0x69CC
0x69CD
0x69CE
0x69CF
0x69D0
1/0
1/0
1/1
1/1
1/0
Action Qualifier Software Force Register
Action Qualifier Continuous S/W Force
Register Set
Dead-Band Generator Control Register
Dead-Band Generator Rising Edge Delay
Count Register
DBRED
Dead-Band Generator Falling Edge Delay
Count Register
DBFED
0x6911
0x6951
0x6991
0x69D1
1/0
TZSEL
0x6912
0x6913
0x6914
0x6915
0x6916
0x6917
0x6918
0x6919
0x691A
0x691B
0x691C
0x691D
0x691E
0x6920
-
0x6952
0x6953
0x6954
0x6955
0x6956
0x6957
0x6958
0x6959
0x695A
0x695B
0x695C
0x695D
0x695E
0x6960
-
0x6992
0x6993
0x6994
0x6995
0x6996
0x6997
0x6998
0x6999
0x699A
0x699B
0x699C
0x699D
0x699E
0x69A0
-
0x69D2
0x69D3
0x69D4
0x69D5
0x69D6
0x69D7
0x69D8
0x69D9
0x69DA
0x69DB
0x69DC
0x69DD
0x69DE
0x69E0
-
1/0
1/0
Trip Zone Select Register(1)
TZDCSEL
TZCTL
Trip Zone Digital Compare Register
Trip Zone Control Register(1)
1/0
TZEINT
TZFLG
1/0
Trip Zone Enable Interrupt Register(1)
Trip Zone Flag Register (1)
1/0
TZCLR
1/0
Trip Zone Clear Register(1)
TZFRC
1/0
Trip Zone Force Register(1)
ETSEL
1/0
Event Trigger Selection Register
Event Trigger Prescale Register
Event Trigger Flag Register
ETPS
1/0
ETFLG
1/0
ETCLR
1/0
Event Trigger Clear Register
ETFRC
1/0
Event Trigger Force Register
PCCTL
1/0
PWM Chopper Control Register
HRPWM Configuration Register(1)
HRPWM MEP Step Register
HRCNFG
HRMSTEP
HRPCTL
TBPRDHRM
TBPRDM
CMPAHRM
CMPAM
DCTRIPSEL
DCACTL
DCBCTL
1/0
1/0
0x6928
0x692A
0x692B
0x692C
0x692D
0x6930
0x6931
0x6932
0x6968
0x696A
0x696B
0x696C
0x696D
0x6970
0x6971
0x6972
0x69A8
0x69AA
0x69AB
0x69AC
0x69AD
0x69B0
0x69B1
0x69B2
0x69E8
0x69EA
0x69EB
0x69EC
0x69ED
0x69F0
0x69F1
0x69F2
1/0
High-resolution Period Control Register(1)
Time Base Period HRPWM Register Mirror
Time Base Period Register Mirror
Compare A HRPWM Register Mirror
Compare A Register Mirror
1/W(2)
1/W(2)
1/W(2)
1/W(2)
1/0
Digital Compare Trip Select Register (1)
Digital Compare A Control Register(1)
Digital Compare B Control Register(1)
1/0
1/0
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 135
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-34. ePWM5–ePWM8 Control and Status Registers (continued)
SIZE (×16)/
#SHADOW
NAME
DCFCTL
ePWM5
0x6933
0x6934
0x6935
0x6936
0x6937
0x6938
0x6939
ePWM6
0x6973
0x6974
0x6975
0x6976
0x6977
0x6978
0x6979
ePWM7
0x69B3
0x69B4
0x69B5
0x69B6
0x69B7
0x69B8
0x69B9
ePWM8
0x69F3
0x69F4
0x69F5
0x69F6
0x69F7
0x69F8
0x69F9
DESCRIPTION
1/0
Digital Compare Filter Control Register(1)
Digital Compare Capture Control
Register(1)
DCCAPCT
1/0
1/1
1/0
1/0
1/0
1/1
DCFOFFSET
DCFOFFSETCNT
DCFWINDOW
DCFWINDOWCNT
DCCAP
Digital Compare Filter Offset Register
Digital Compare Filter Offset Counter
Register
Digital Compare Filter Window Register
Digital Compare Filter Window Counter
Register
Digital Compare Counter Capture Register
(1) Registers that are EALLOW protected.
(2) W = Write to shadow register
Copyright © 2021 Texas Instruments Incorporated
136 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Time-Base (TB)
CTR=ZERO
Sync
In/Out
TBPRD Shadow (24)
TBPRD Active (24)
EPWMxSYNCO
CTR=CMPB
Disabled
Select
Mux
TBPRDHR (8)
8
CTR=PRD
TBCTL[SYNCOSEL]
TBCTL[PHSEN]
EPWMxSYNCI
DCAEVT1.sync
DCBEVT1.sync
Counter
Up/Down
(16 Bit)
TBCTL[SWFSYNC]
(Software Forced
Sync)
CTR=ZERO
CTR_Dir
TCBNT
Active (16)
CTR=PRD
CTR=ZERO
TBPHSHR (8)
EPWMxINT
CTR=PRD or ZERO
CTR=CMPA
Event
Trigger
and
Interrupt
(ET)
16
8
EPWMxSOCA
Phase
Control
CTR=CMPB
CTR_Dir
(A)
DCAEVT1.soc
(A)
TBPHS Active (24)
EPWMxSOCB
EPWMxSOCA
ADC
DCBEVT1.soc
EPWMxSOCB
Action
Qualifier
(AQ)
CTR=CMPA
CMPAHR (8)
16
High-resolution PWM (HRPWM)
CMPA Active (24)
CMPA Shadow (24)
EPWMxA
EPWMA
EPWMB
PWM
Chopper
(PC)
Trip
Zone
(TZ)
Dead
Band
(DB)
CTR=CMPB
16
EPWMxB
EPWMxTZINT
TZ1 to TZ3
EMUSTOP
CMPB Active (16)
CMPB Shadow (16)
CLOCKFAIL
(B)
EQEP1ERR
CTR=ZERO
DCAEVT1.inter
DCBEVT1.inter
(A)
(A)
(A)
(A)
DCAEVT1.force
DCAEVT2.force
DCBEVT1.force
DCBEVT2.force
DCAEVT2.inter
DCBEVT2.inter
Copyright © 2017, Texas Instruments Incorporated
A. These events are generated by the Type 1 ePWM digital compare (DC) submodule based on the levels of the COMPxOUT and TZ
signals.
B. This signal exists only on devices with an eQEP1 module.
Figure 8-49. ePWM Submodules Showing Critical Internal Signal Interconnections
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 137
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.9.1 ePWM Electrical Data/Timing
PWM refers to PWM outputs on ePWM1–8. Section 8.9.9.1.1 shows the PWM timing requirements and Section
8.9.9.1.2, switching characteristics.
8.9.9.1.1 ePWM Timing Requirements
MIN(1)
2tc(SCO)
MAX
UNIT
cycles
cycles
cycles
Asynchronous
Synchronous
tw(SYCIN)
Sync input pulse width
2tc(SCO)
With input qualifier
1tc(SCO) + tw(IQSW)
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
8.9.9.1.2 ePWM Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
33.33
MAX
UNIT
ns
tw(PWM)
Pulse duration, PWMx output high/low
Sync output pulse width
tw(SYNCOUT)
8tc(SCO)
cycles
Delay time, trip input active to PWM forced high
Delay time, trip input active to PWM forced low
td(PWM)tza
no pin load
25
20
ns
ns
td(TZ-PWM)HZ
Delay time, trip input active to PWM Hi-Z
8.9.9.2 Trip-Zone Input Timing
Section 8.9.9.2.1 lists the trip-zone input timing requirements. Figure 8-50 shows the PWM Hi-Z characteristics.
8.9.9.2.1 Trip-Zone Input Timing Requirements
MIN(1)
2tc(TBCLK)
MAX UNIT
cycles
Asynchronous
Synchronous
tw(TZ)
Pulse duration, TZx input low
2tc(TBCLK)
cycles
With input qualifier
2tc(TBCLK) + tw(IQSW)
cycles
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
SYSCLK
tw(TZ)
TZ(A)
td(TZ-PWM)HZ
PWM(B)
A. TZ - TZ1, TZ2, TZ3, TZ4, TZ5, TZ6
B. PWM refers to all the PWM pins in the device. The state of the PWM pins after TZ is taken high depends on the PWM recovery software.
Figure 8-50. PWM Hi-Z Characteristics
Copyright © 2021 Texas Instruments Incorporated
138 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.10 High-Resolution PWM (HRPWM)
This module combines multiple delay lines in a single module and a simplified calibration system by using a
dedicated calibration delay line. For each ePWM module there is one HR delay line.
The HRPWM module offers PWM resolution (time granularity) that is significantly better than what can be
achieved using conventionally derived digital PWM methods. The key points for the HRPWM module are:
•
•
Significantly extends the time resolution capabilities of conventionally derived digital PWM
This capability can be used in both single edge (duty cycle and phase-shift control) as well as dual edge
control for frequency/period modulation.
•
•
Finer time granularity control or edge positioning is controlled through extensions to the Compare A and
Phase registers of the ePWM module.
HRPWM capabilities, when available on a particular device, are offered only on the A signal path of an
ePWM module (that is, on the EPWMxA output). EPWMxB output has conventional PWM capabilities.
Note
The minimum SYSCLKOUT frequency allowed for HRPWM is 60 MHz.
Note
When dual-edge high-resolution is enabled (high-resolution period mode), the PWMxB channel will
have ±1–2 TBCLK cycles of jitter on the output.
8.9.10.1 HRPWM Electrical Data/Timing
Section 8.9.10.1.1 shows the high-resolution PWM switching characteristics.
8.9.10.1.1 High-Resolution PWM Characteristics
PARAMETER(1)
MIN
TYP
MAX UNIT
310 ps
Micro Edge Positioning (MEP) step size(2)
150
(1) The HRPWM operates at a minimum SYSCLKOUT frequency of 60 MHz.
(2) The MEP step size will be largest at high temperature and minimum voltage on VDD. MEP step size will increase with higher
temperature and lower voltage and decrease with lower temperature and higher voltage.
Applications that use the HRPWM feature should use MEP Scale Factor Optimizer (SFO) estimation software functions. See the TI
software libraries for details of using SFO function in end applications. SFO functions help to estimate the number of MEP steps per
SYSCLKOUT period dynamically while the HRPWM is in operation.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 139
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.11 Enhanced Capture Module (eCAP1)
The device contains an enhanced capture (eCAP) module. Figure 8-51 shows a functional block diagram of a
module.
CTRPHS
(phase register−32 bit)
APWM mode
SYNCIn
CTR_OVF
OVF
CTR [0−31]
PRD [0−31]
CMP [0−31]
TSCTR
(counter−32 bit)
SYNCOut
PWM
compare
logic
Delta−mode
RST
32
CTR=PRD
CTR=CMP
CTR [0−31]
PRD [0−31]
32
eCAPx
32
LD1
CAP1
(APRD active)
Polarity
select
LD
APRD
shadow
32
CMP [0−31]
32
32
LD2
CAP2
(ACMP active)
Polarity
select
LD
Event
qualifier
Event
Pre-scale
32
ACMP
shadow
Polarity
select
32
32
LD3
LD4
CAP3
(APRD shadow)
LD
CAP4
(ACMP shadow)
Polarity
select
LD
4
Capture events
4
CEVT[1:4]
Interrupt
Trigger
and
Flag
control
Continuous /
Oneshot
Capture Control
to PIE
CTR_OVF
CTR=PRD
CTR=CMP
Copyright © 2017, Texas Instruments Incorporated
Figure 8-51. eCAP Functional Block Diagram
The eCAP module is clocked at the SYSCLKOUT rate.
The clock enable bits (ECAP1 ENCLK) in the PCLKCR1 register turn off the eCAP module individually (for low-
power operation). Upon reset, ECAP1ENCLK is set to low, indicating that the peripheral clock is off.
Copyright © 2021 Texas Instruments Incorporated
140 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
www.ti.com
NAME
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
Table 8-35. eCAP Control and Status Registers
EALLOW
PROTECTED
eCAP1
eCAP2
eCAP3
SIZE (×16)
DESCRIPTION
Timestamp Counter
TSCTR
CTRPHS
CAP1
0x6A00
0x6A02
0x6A04
0x6A06
0x6A08
0x6A0A
0x6A20
0x6A22
0x6A24
0x6A26
0x6A28
0x6A2A
0x6A40
0x6A42
0x6A44
0x6A46
0x6A48
0x6A4A
2
2
2
2
2
2
No
No
No
No
No
No
Counter Phase Offset Value Register
Capture 1 Register
CAP2
Capture 2 Register
CAP3
Capture 3 Register
CAP4
Capture 4 Register
0x6A0C to
0x6A12
0x6A2C to
0x6A32
0x6A4C to
0x6A52
Reserved
8
No
Reserved
ECCTL1
ECCTL2
ECEINT
ECFLG
ECCLR
ECFRC
0x6A14
0x6A15
0x6A16
0x6A17
0x6A18
0x6A19
0x6A34
0x6A35
0x6A36
0x6A37
0x6A38
0x6A39
0x6A54
0x6A55
0x6A56
0x6A57
0x6A58
0x6A59
1
1
1
1
1
1
No
No
No
No
No
No
Capture Control Register 1
Capture Control Register 2
Capture Interrupt Enable Register
Capture Interrupt Flag Register
Capture Interrupt Clear Register
Capture Interrupt Force Register
0x6A1A to
0x6A1F
0x6A3A to
0x6A3F
0x6A5A to
0x6A5F
Reserved
6
No
Reserved
8.9.11.1 eCAP Electrical Data/Timing
Section 8.9.11.1.1 shows the eCAP timing requirement and Section 8.9.11.1.2 shows the eCAP switching
characteristics.
8.9.11.1.1 Enhanced Capture (eCAP) Timing Requirement
MIN(1)
2tc(SCO)
MAX UNIT
Asynchronous
Synchronous
tw(CAP)
Capture input pulse width
2tc(SCO)
cycles
With input qualifier
1tc(SCO) + tw(IQSW)
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
8.9.11.1.2 eCAP Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
MAX
UNIT
tw(APWM)
Pulse duration, APWMx output high/low
20
ns
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 141
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.12 High-Resolution Capture Modules (HRCAP1 to HRCAP4)
The device contains up to four high-resolution capture (HRCAP) modules. The High-Resolution Capture
(HRCAP) module measures the difference between external pulses with a typical resolution of 300 ps.
Uses for the HRCAP include:
•
•
•
•
•
•
Capacitive touch applications
High-resolution period and duty cycle measurements of pulse train cycles
Instantaneous speed measurements
Instantaneous frequency measurements
Voltage measurements across an isolation boundary
Distance measurement (sonar) and scanning
The HRCAP module features include:
•
•
•
•
•
•
•
•
Pulse width capture in either non-high-resolution or high-resolution modes
Difference (Delta) mode pulse width capture
Typical high-resolution capture on the order of 300 ps resolution on each edge
Interrupt on either falling or rising edge
Continuous mode capture of pulse widths in 2-deep buffer
Calibration logic for precision high-resolution capture
All of the above resources are dedicated to a single input pin
HRCAP calibration software library supplied by TI is used for both calibration and calculating fractional pulse
widths
The HRCAP module includes one capture channel in addition to a high-resolution calibration block, which
connects internally to the last available ePWMxA HRPWM channel when calibrating (that is, if there are eight
ePWMs with HRPWM capability, it will be HRPWM8A).
Each HRCAP channel has the following independent key resources:
•
•
Dedicated input capture pin
16-bit HRCAP clock which is either equal to the PLL2 output frequency (asynchronous to SYSCLK2) or
SYSCLKOUT
•
High-resolution pulse width capture in a 2-deep buffer
HRCAP Calibration Logic
EPWMx
EPWMxA
HRPWM
HRCAPxENCLK
SYSCLKOUT
PLL2CLK
HRCAPx
Module
GPIO
Mux
HRCAP Calibration Signal (Internal)
PIE
HRCAPxINTn
HRCAPx
Figure 8-52. HRCAP Functional Block Diagram
Copyright © 2021 Texas Instruments Incorporated
142 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-36. HRCAP Registers
SIZE
(×16)
NAME
HRCAP1
HRCAP2
HRCAP3
HRCAP4
DESCRIPTION
HCCTL
0x6AC0
0x6AC1
0x6AC2
0x6AC3
0x6AC4
0x6AE0
0x6AE1
0x6AE2
0x6AE3
0x6AE4
0x6C80
0x6C81
0x6C82
0x6C83
0x6C84
0x6CA0
0x6CA1
0x6CA2
0x6CA3
0x6CA4
1
1
1
1
1
HRCAP Control Register(1)
HCIFR
HRCAP Interrupt Flag Register
HRCAP Interrupt Clear Register(1)
HRCAP Interrupt Force Register(1)
HRCAP 16-bit Counter Register
HCICLR
HCIFRC
HCCOUNTER
HRCAP Capture Counter on Rising Edge
0 Register
HCCAPCNTRISE0
HCCAPCNTFALL0
HCCAPCNTRISE1
HCCAPCNTFALL1
0x6AD0
0x6AD2
0x6AD8
0x6ADA
0x6AF0
0x6AF2
0x6AF8
0x6AFA
0x6C90
0x6C92
0x6C98
0x6C9A
0x6CB0
0x6CB2
0x6CB8
0x6CBA
1
1
1
1
HRCAP Capture Counter on
Falling Edge 0 Register
HRCAP Capture Counter on Rising Edge
1 Register
HRCAP Capture Counter on
Falling Edge 1 Register
(1) Registers that are EALLOW-protected.
8.9.12.1 HRCAP Electrical Data/Timing
8.9.12.1.1 High-Resolution Capture (HRCAP) Timing Requirements
MIN
NOM
MAX UNIT
tc(HCCAPCLK)
tw(HRCAP)
Cycle time, HRCAP capture clock
Pulse width, HRCAP capture
HRCAP step size(2)
8.333
10.204
ns
ns
ps
(1)
7tc(HCCAPCLK)
300
(1) The listed minimum pulse width does not take into account the limitation that all relevant HCCAP registers must be read and RISE/
FALL event flags cleared within the pulse width to ensure valid capture data.
(2) HRCAP step size will increase with low voltage and high temperature and decrease with high voltage and low temperature.
Applications that use the HRCAP in high-resolution mode should use the HRCAP calibration functions to dynamically calibrate for
varying operating conditions.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 143
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.13 Enhanced Quadrature Encoder Modules (eQEP1, eQEP2)
The device contains up to two enhanced quadrature encoder (eQEP) modules. Table 8-37 provides a summary
of the eQEP registers.
Table 8-37. eQEP Control and Status Registers
eQEP1
SIZE(×16)/
#SHADOW
eQEP1
ADDRESS
eQEP2
ADDRESS
NAME
QPOSCNT
REGISTER DESCRIPTION
0x6B00
0x6B02
0x6B04
0x6B06
0x6B08
0x6B0A
0x6B0C
0x6B0E
0x6B10
0x6B12
0x6B13
0x6B14
0x6B15
0x6B16
0x6B17
0x6B18
0x6B19
0x6B1A
0x6B1B
0x6B1C
0x6B1D
0x6B1E
0x6B1F
0x6B20
0x6B40
0x6B42
0x6B44
0x6B46
0x6B48
0x6B4A
0x6B4C
0x6B4E
0x6B50
0x6B52
0x6B53
0x6B54
0x6B55
0x6B56
0x6B57
0x6B58
0x6B59
0x6B5A
0x6B5B
0x6B5C
0x6B5D
0x6B5E
0x6B5F
0x6B60
2/0
2/0
2/0
2/1
2/0
2/0
2/0
2/0
2/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
eQEP Position Counter
QPOSINIT
QPOSMAX
QPOSCMP
QPOSILAT
QPOSSLAT
QPOSLAT
QUTMR
eQEP Initialization Position Count
eQEP Maximum Position Count
eQEP Position-compare
eQEP Index Position Latch
eQEP Strobe Position Latch
eQEP Position Latch
eQEP Unit Timer
QUPRD
eQEP Unit Period Register
eQEP Watchdog Timer
QWDTMR
QWDPRD
QDECCTL
QEPCTL
QCAPCTL
QPOSCTL
QEINT
eQEP Watchdog Period Register
eQEP Decoder Control Register
eQEP Control Register
eQEP Capture Control Register
eQEP Position-compare Control Register
eQEP Interrupt Enable Register
eQEP Interrupt Flag Register
eQEP Interrupt Clear Register
eQEP Interrupt Force Register
eQEP Status Register
QFLG
QCLR
QFRC
QEPSTS
QCTMR
eQEP Capture Timer
QCPRD
eQEP Capture Period Register
eQEP Capture Timer Latch
eQEP Capture Period Latch
QCTMRLAT
QCPRDLAT
0x6B21 to
0x6B3F
0x6B61 to
0x6B7F
Reserved
31/0
Copyright © 2021 Texas Instruments Incorporated
144 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Figure 8-53 shows the block diagram of the eQEP module.
System Control
Registers
To CPU
EQEPxENCLK
SYSCLKOUT
QCPRD
QCAPCTL
16
QCTMR
16
16
Quadrature
Capture
Unit
QCTMRLAT
QCPRDLAT
(QCAP)
QUTMR
QUPRD
QWDTMR
QWDPRD
Registers
Used by
Multiple Units
32
16
QEPCTL
QEPSTS
QFLG
UTOUT
QWDOG
UTIME
QDECCTL
16
WDTOUT
EQEPxAIN
EQEPxBIN
EQEPxIIN
EQEPxA/XCLK
EQEPxB/XDIR
EQEPxI
QCLK
QDIR
QI
EQEPxINT
16
PIE
Position Counter/
Control Unit
(PCCU)
EQEPxIOUT
EQEPxIOE
EQEPxSIN
EQEPxSOUT
EQEPxSOE
Quadrature
Decoder
(QDU)
QS
GPIO
MUX
QPOSLAT
QPOSSLAT
QPOSILAT
PHE
PCSOUT
EQEPxS
32
32
16
QPOSCNT
QPOSINIT
QPOSMAX
QEINT
QFRC
QPOSCMP
QCLR
QPOSCTL
Enhanced QEP (eQEP) Peripheral
Copyright © 2017, Texas Instruments Incorporated
Figure 8-53. eQEP Functional Block Diagram
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 145
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.13.1 eQEP Electrical Data/Timing
Section 8.9.13.1.1 shows the eQEP timing requirement and Section 8.9.13.1.2 shows the eQEP switching
characteristics.
8.9.13.1.1 Enhanced Quadrature Encoder Pulse (eQEP) Timing Requirements
MIN(1)
MAX
UNIT
Asynchronous(2)/Synchronous
With input qualifier
2tc(SCO)
tw(QEPP)
QEP input period
cycles
2[1tc(SCO) + tw(IQSW)
]
Asynchronous(2)/Synchronous
2tc(SCO)
2tc(SCO) +tw(IQSW)
2tc(SCO)
tw(INDEXH)
tw(INDEXL)
tw(STROBH)
tw(STROBL)
QEP Index Input High time
QEP Index Input Low time
QEP Strobe High time
QEP Strobe Input Low time
cycles
cycles
cycles
cycles
With input qualifier
Asynchronous(2)/Synchronous
With input qualifier
2tc(SCO) + tw(IQSW)
2tc(SCO)
2tc(SCO) + tw(IQSW)
2tc(SCO)
Asynchronous(2)/Synchronous
With input qualifier
Asynchronous(2)/Synchronous
With input qualifier
2tc(SCO) +tw(IQSW)
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
(2) Refer to the TMS320F2806x MCUs Silicon Errata for limitations in the asynchronous mode.
8.9.13.1.2 eQEP Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
MAX
4tc(SCO)
6tc(SCO)
UNIT
cycles
cycles
td(CNTR)xin
Delay time, external clock to counter increment
td(PCS-OUT)QEP
Delay time, QEP input edge to position compare sync output
Copyright © 2021 Texas Instruments Incorporated
146 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.14 JTAG Port
On the 2806x device, the JTAG port is reduced to five pins ( TRST, TCK, TDI, TMS, TDO). TCK, TDI, TMS, and
TDO pins are also GPIO pins. The TRST signal selects either JTAG or GPIO operating mode for the pins in
Figure 8-54. During emulation/debug, the GPIO function of these pins are not available. If the GPIO38/TCK/
XCLKIN pin is used to provide an external clock, an alternate clock source should be used to clock the device
during emulation/debug because this pin will be needed for the TCK function.
Note
In 2806x devices, the JTAG pins may also be used as GPIO pins. Care should be taken in the board
design to ensure that the circuitry connected to these pins do not affect the emulation capabilities of
the JTAG pin function. Any circuitry connected to these pins should not prevent the debug probe from
driving (or being driven by) the JTAG pins for successful debug.
TRST = 0: JTAG Disabled (GPIO Mode)
TRST = 1: JTAG Mode
TRST
TRST
XCLKIN
GPIO38_in
TCK
TCK/GPIO38
GPIO38_out
C28x
Core
GPIO37_in
TDO
TDO/GPIO37
1
0
GPIO37_out
GPIO36_in
1
0
TMS
TMS/GPIO36
TDI/GPIO35
1
GPIO36_out
GPIO35_in
1
0
TDI
1
GPIO35_out
Figure 8-54. JTAG/GPIO Multiplexing
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 147
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.15 General-Purpose Input/Output (GPIO) MUX
The GPIO MUX can multiplex up to three independent peripheral signals on a single GPIO pin in addition to
providing individual pin bit-banging I/O capability.
The device supports 45 GPIO pins. The GPIO control and data registers are mapped to Peripheral Frame 1 to
enable 32-bit operations on the registers (along with 16-bit operations). Table 8-38 shows the GPIO register
mapping.
Table 8-38. GPIO Registers
NAME
ADDRESS
SIZE (×16)
DESCRIPTION
GPIO CONTROL REGISTERS (EALLOW PROTECTED)
GPACTRL
GPAQSEL1
GPAQSEL2
GPAMUX1
GPAMUX2
GPADIR
0x6F80
0x6F82
0x6F84
0x6F86
0x6F88
0x6F8A
0x6F8C
0x6F90
0x6F92
0x6F94
0x6F96
0x6F98
0x6F9A
0x6F9C
0x6FB6
0x6FBA
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
GPIO A Control Register (GPIO0 to 31)
GPIO A Qualifier Select 1 Register (GPIO0 to 15)
GPIO A Qualifier Select 2 Register (GPIO16 to 31)
GPIO A MUX 1 Register (GPIO0 to 15)
GPIO A MUX 2 Register (GPIO16 to 31)
GPIO A Direction Register (GPIO0 to 31)
GPIO A Pullup Disable Register (GPIO0 to 31)
GPIO B Control Register (GPIO32 to 44)
GPIO B Qualifier Select 1 Register (GPIO32 to 44)
GPIO B Qualifier Select 2 Register
GPAPUD
GPBCTRL
GPBQSEL1
GPBQSEL2
GPBMUX1
GPBMUX2
GPBDIR
GPIO B MUX 1 Register (GPIO32 to 44)
GPIO B MUX 2 Register (GPIO50 to 58)
GPIO B Direction Register (GPIO32 to 44)
GPIO B Pullup Disable Register (GPIO32 to 44)
Analog, I/O mux 1 register (AIO0 to AIO15)
Analog, I/O Direction Register (AIO0 to AIO15)
GPBPUD
AIOMUX1
AIODIR
GPIO DATA REGISTERS (NOT EALLOW PROTECTED)
GPADAT
0x6FC0
0x6FC2
0x6FC4
0x6FC6
0x6FC8
0x6FCA
0x6FCC
0x6FCE
0x6FD8
0x6FDA
0x6FDC
0x6FDE
2
2
2
2
2
2
2
2
2
2
2
2
GPIO A Data Register (GPIO0 to 31)
GPASET
GPIO A Data Set Register (GPIO0 to 31)
GPIO A Data Clear Register (GPIO0 to 31)
GPIO A Data Toggle Register (GPIO0 to 31)
GPIO B Data Register (GPIO32 to 44)
GPACLEAR
GPATOGGLE
GPBDAT
GPBSET
GPIO B Data Set Register (GPIO32 to 44)
GPIO B Data Clear Register (GPIO32 to 44)
GPIO B Data Toggle Register (GPIO32 to 44)
Analog I/O Data Register (AIO0 to AIO15)
Analog I/O Data Set Register (AIO0 to AIO15)
Analog I/O Data Clear Register (AIO0 to AIO15)
Analog I/O Data Toggle Register (AIO0 to AIO15)
GPBCLEAR
GPBTOGGLE
AIODAT
AIOSET
AIOCLEAR
AIOTOGGLE
GPIO INTERRUPT AND LOW-POWER MODES SELECT REGISTERS (EALLOW PROTECTED)
GPIOXINT1SEL
GPIOXINT2SEL
GPIOXINT3SEL
GPIOLPMSEL
0x6FE0
0x6FE1
0x6FE2
0x6FE8
1
1
1
2
XINT1 GPIO Input Select Register (GPIO0 to 31)
XINT2 GPIO Input Select Register (GPIO0 to 31)
XINT3 GPIO Input Select Register (GPIO0 to 31)
LPM GPIO Select Register (GPIO0 to 31)
Note
There is a two-SYSCLKOUT cycle delay from when the write to the GPxMUXn/AIOMUXn and
GPxQSELn registers occurs to when the action is valid.
Copyright © 2021 Texas Instruments Incorporated
148 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-39. GPIOA MUX
DEFAULT AT RESET
PRIMARY I/O
PERIPHERAL
SELECTION 1
PERIPHERAL
SELECTION 2
PERIPHERAL
SELECTION 3
FUNCTION(1) (2)
GPAMUX1 REGISTER
(GPAMUX1 BITS = 00)
(GPAMUX1 BITS = 01)
(GPAMUX1 BITS = 10)
(GPAMUX1 BITS = 11)
BITS
1-0
GPIO0
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
GPIO8
GPIO9
GPIO10
GPIO11
GPIO12
GPIO13
GPIO14
GPIO15
EPWM1A (O)
EPWM1B (O)
EPWM2A (O)
EPWM2B (O)
EPWM3A (O)
EPWM3B (O)
EPWM4A (O)
EPWM4B (O)
EPWM5A (O)
EPWM5B (O)
EPWM6A (O)
EPWM6B (O)
TZ1 (I)
Reserved
Reserved
Reserved
COMP1OUT (O)
Reserved
3-2
5-4
Reserved
7-6
SPISOMIA (I/O)
Reserved
COMP2OUT (O)
Reserved
9-8
11-10
13-12
15-14
17-16
19-18
21-20
23-22
25-24
27-26
29-28
31-30
SPISIMOA (I/O)
EPWMSYNCI (I)
SCIRXDA (I)
Reserved
ECAP1 (I/O)
EPWMSYNCO (O)
ECAP2 (I/O)
ADCSOCAO (O)
ECAP3 (I/O)
SCITXDB (O)
Reserved
ADCSOCBO (O)
ECAP1 (I/O)
SCIRXDB (I)
SCITXDA (O)
Reserved
SPISIMOB (I/O)
SPISOMIB (I/O)
SPICLKB (I/O)
SPISTEB (I/O)
TZ2 (I)
TZ3 (I)
SCITXDB (O)
SCIRXDB (I)
ECAP2 (I/O)
GPAMUX2 REGISTER
BITS
(GPAMUX2 BITS = 00)
(GPAMUX2 BITS = 01)
(GPAMUX2 BITS = 10)
(GPAMUX2 BITS = 11)
1-0
GPIO16
GPIO17
SPISIMOA (I/O)
SPISOMIA (I/O)
SPICLKA (I/O)
SPISTEA (I/O)
EQEP1A (I)
Reserved
Reserved
TZ2 (I)
3-2
TZ3 (I)
5-4
GPIO18
SCITXDB (O)
SCIRXDB (I)
MDXA (O)
XCLKOUT (O)
ECAP1 (I/O)
COMP1OUT (O)
COMP2OUT (O)
SCITXDB (O)
SCIRXDB (I)
SPISIMOB (I/O)
SPISOMIB (I/O)
SPICLKB (I/O)
SPISTEB (I/O)
TZ2 (I)
7-6
GPIO19/XCLKIN
GPIO20
9-8
11-10
13-12
15-14
17-16
19-18
21-20
23-22
25-24
27-26
29-28
31-30
GPIO21
EQEP1B (I)
MDRA (I)
GPIO22
EQEP1S (I/O)
EQEP1I (I/O)
ECAP1 (I/O)
ECAP2 (I/O)
ECAP3 (I/O)
HRCAP2 (I)
MCLKXA (I/O)
MFSXA (I/O)
EQEP2A(3) (I)
EQEP2B(3) (I)
EQEP2I(3) (I/O)
EQEP2S(3) (I/O)
SDAA (I/OD)
SCLA (I/OD)
EQEP2I(3) (I/O)
EQEP2S(3) (I/O)
GPIO23
GPIO24
GPIO25
GPIO26(4)
GPIO27(4)
GPIO28
SCIRXDA (I)
SCITXDA (O)
CANRXA (I)
CANTXA (O)
GPIO29
TZ3 (I)
GPIO30
EPWM7A (O)
EPWM8A (O)
GPIO31
(1) The word "Reserved" means that there is no peripheral assigned to this GPxMUX1/2 register setting. Should it be selected, the state of
the pin will be undefined and the pin may be driven. This selection is a reserved configuration for future expansion.
(2) I = Input, O = Output, OD = Open Drain
(3) The eQEP2 peripheral is not available on the 80-pin PN or PFP package.
(4) To enable the USB functionality on GPIO26 (USB0DP, positive differential half of the USB signal) and GPIO27 (USB0DM, negative
differential half of the USB signal), set the USBIOEN bit in the GPACTRL2 register. Depending on your USB application, additional pins
may be required to maintain compliance with the USB 2.0 Specification. For more information, see the Universal Serial Bus (USB)
Controller chapter of the TMS320x2806x Technical Reference Manual .
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 149
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-40. GPIOB MUX
DEFAULT AT RESET
PERIPHERAL
SELECTION 1
PERIPHERAL
SELECTION 2
PERIPHERAL
SELECTION 3
PRIMARY I/O
FUNCTION(1) (2)
GPBMUX1 REGISTER
BITS
(GPBMUX1 BITS = 00)
(GPBMUX1 BITS = 01)
(GPBMUX1 BITS = 10)
(GPBMUX1 BITS = 11)
1-0
GPIO32
GPIO33
SDAA (I/OD)
SCLA (I/OD)
COMP2OUT (O)
Reserved
EPWMSYNCI (I)
EPWMSYNCO (O)
Reserved
ADCSOCAO (O)
ADCSOCBO (O)
COMP3OUT (O)
Reserved
3-2
5-4
GPIO34
7-6
GPIO35 (TDI)
GPIO36 (TMS)
GPIO37 (TDO)
GPIO38/XCLKIN (TCK)
GPIO39
Reserved
9-8
Reserved
Reserved
Reserved
11-10
13-12
15-14
17-16
19-18
21-20
23-22
25-24
27-26
29-28
31-30
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
GPIO40(3)
EPWM7A (O)
EPWM7B (O)
EPWM8A (O)
EPWM8B (O)
MFSRA (I/O)
Reserved
SCITXDB (O)
SCIRXDB (I)
TZ1 (I)
Reserved
GPIO41(3)
Reserved
GPIO42(3)
COMP1OUT (O)
COMP2OUT (O)
EPWM7B (O)
Reserved
GPIO43(3)
TZ2 (I)
GPIO44(3)
SCIRXDB (I)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
GPBMUX2 REGISTER
BITS
(GPBMUX2 BITS = 00)
(GPBMUX2 BITS = 01)
(GPBMUX2 BITS = 10)
(GPBMUX2 BITS = 11)
1-0
Reserved
Reserved
GPIO50(3)
GPIO51(3)
GPIO52(3)
GPIO53(3)
GPIO54(3)
GPIO55(3)
GPIO56(3)
GPIO57(3)
GPIO58(3)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TZ1 (I)
3-2
5-4
EQEP1A (I)
EQEP1B (I)
EQEP1S (I/O)
EQEP1I (I/O)
SPISIMOA (I/O)
SPISOMIA (I/O)
SPICLKA (I/O)
SPISTEA (I/O)
MCLKRA (I/O)
Reserved
MDXA (O)
MDRA (I)
7-6
TZ2 (I)
9-8
MCLKXA (I/O)
MFSXA (I/O)
EQEP2A (I)
EQEP2B (I)
EQEP2I (I/O)
EQEP2S (I/O)
SCITXDB (O)
Reserved
TZ3 (I)
11-10
13-12
15-14
17-16
19-18
21-20
23-22
25-24
27-26
29-28
31-30
Reserved
HRCAP1 (I)
HRCAP2 (I)
HRCAP3 (I)
HRCAP4 (I)
EPWM7A (O)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
(1) The word "Reserved" means that there is no peripheral assigned to this GPxMUX1/2 register setting. Should it be selected, the state of
the pin will be undefined and the pin may be driven. This selection is a reserved configuration for future expansion.
(2) I = Input, O = Output, OD = Open Drain
(3) This pin is not available in the 80-pin PN or PFP package.
Copyright © 2021 Texas Instruments Incorporated
150 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
Table 8-41. Analog MUX for 100-Pin PZ and 100-Pin PZP Packages
DEFAULT AT RESET(1)
PERIPHERAL SELECTION 2 AND
AIOx AND PERIPHERAL SELECTION 1
PERIPHERAL SELECTION 3
AIOMUX1 REGISTER BITS
AIOMUX1 BITS = 0,x
ADCINA0 (I)
ADCINA1 (I)
AIO2 (I/O)
AIOMUX1 BITS = 1,x
ADCINA0 (I)
1-0
3-2
ADCINA1 (I)
5-4
ADCINA2 (I), COMP1A (I)
ADCINA3 (I)
7-6
ADCINA3 (I)
AIO4 (I/O)
9-8
ADCINA4 (I), COMP2A (I)
ADCINA5 (I)
11-10
13-12
15-14
17-16
19-18
21-20
23-22
25-24
27-26
29-28
31-30
ADCINA5 (I)
AIO6 (I/O)
ADCINA6 (I), COMP3A (I)
ADCINA7 (I)
ADCINA7 (I)
ADCINB0 (I)
ADCINB1 (I)
AIO10 (I/O)
ADCINB3 (I)
AIO12 (I/O)
ADCINB5 (I)
AIO14 (I/O)
ADCINB7 (I)
ADCINB0 (I)
ADCINB1 (I)
ADCINB2 (I), COMP1B (I)
ADCINB3 (I)
ADCINB4 (I), COMP2B (I)
ADCINB5 (I)
ADCINB6 (I), COMP3B (I)
ADCINB7 (I)
(1) I = Input, O = Output
Table 8-42. Analog MUX for 80-Pin PN and 80-Pin PFP Packages
DEFAULT AT RESET(1)
PERIPHERAL SELECTION 2 AND
PERIPHERAL SELECTION 3
AIOx AND PERIPHERAL SELECTION 1
AIOMUX1 REGISTER BITS
AIOMUX1 BITS = 0,x
ADCINA0 (I), VREFHI (I)
ADCINA1 (I)
AIO2 (I/O)
–
AIOMUX1 BITS = 1,x
ADCINA0 (I), VREFHI (I)
ADCINA1 (I)
1-0
3-2
5-4
ADCINA2 (I), COMP1A (I)
–
7-6
9-8
AIO4 (I/O)
ADCINA5 (I)
AIO6 (I/O)
–
ADCINA4 (I), COMP2A (I)
ADCINA5 (I)
11-10
13-12
15-14
17-16
19-18
21-20
23-22
25-24
27-26
29-28
31-30
ADCINA6 (I), COMP3A (I)
–
ADCINB0 (I)
ADCINB1 (I)
AIO10 (I/O)
–
ADCINB0 (I)
ADCINB1 (I)
ADCINB2 (I), COMP1B (I)
–
AIO12 (I/O)
ADCINB5 (I)
AIO14 (I/O)
–
ADCINB4 (I), COMP2B (I)
ADCINB5 (I)
ADCINB6 (I), COMP3B (I)
–
(1) I = Input, O = Output
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 151
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
The user can select the type of input qualification for each GPIO pin through the GPxQSEL1/2 registers from
four choices:
•
Synchronization To SYSCLKOUT Only (GPxQSEL1/2 = 0, 0): This is the default mode of all GPIO pins at
reset and it simply synchronizes the input signal to the system clock (SYSCLKOUT).
Qualification Using Sampling Window (GPxQSEL1/2 = 0, 1 and 1, 0): In this mode the input signal, after
synchronization to the system clock (SYSCLKOUT), is qualified by a specified number of cycles before the
input is allowed to change.
•
•
•
The sampling period is specified by the QUALPRD bits in the GPxCTRL register and is configurable in
groups of 8 signals. The sampling period specifies a multiple of SYSCLKOUT cycles for sampling the input
signal. The sampling window is either 3-samples or 6-samples wide and the output is only changed when
ALL samples are the same (all 0s or all 1s) as shown in Figure 4-18 (for 6 sample mode).
No Synchronization (GPxQSEL1/2 = 1,1): This mode is used for peripherals where synchronization is not
required (synchronization is performed within the peripheral).
Due to the multilevel multiplexing that is required on the device, there may be cases where a peripheral input
signal can be mapped to more then one GPIO pin. Also, when an input signal is not selected, the input signal will
default to either a 0 or 1 state, depending on the peripheral.
Copyright © 2021 Texas Instruments Incorporated
152 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
GPIOXINT1SEL
GPIOLMPSEL
LPMCR0
GPIOXINT2SEL
GPIOXINT3SEL
External Interrupt
MUX
Low-Power
Modes Block
PIE
Asynchronous
path
GPxDAT (read)
GPxQSEL1/2
GPxCTRL
GPxPUD
N/C
00
01
Peripheral 1 Input
Peripheral 2 Input
Input
Internal
Pullup
Qualification
10
11
Peripheral 3 Input
GPxTOGGLE
Asynchronous path
GPIOx pin
GPxCLEAR
GPxSET
00
01
GPxDAT (latch)
Peripheral 1 Output
10
11
Peripheral 2 Output
Peripheral 3 Output
High Impedance
Output Control
GPxDIR (latch)
00
01
Peripheral 1 Output Enable
Peripheral 2 Output Enable
0 = Input, 1 = Output
XRS
10
11
Peripheral 3 Output Enable
= Default at Reset
GPxMUX1/2
A. x stands for the port, either A or B. For example, GPxDIR refers to either the GPADIR and GPBDIR register depending on the particular
GPIO pin selected.
B. GPxDAT latch/read are accessed at the same memory location.
C. This is a generic GPIO MUX block diagram. Not all options may be applicable for all GPIO pins. See the Systems Control and Interrupts
chapter of the TMS320x2806x Technical Reference Manual for pin-specific variations.
Figure 8-55. GPIO Multiplexing
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 153
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.15.1 GPIO Electrical Data/Timing
8.9.15.1.1 GPIO Output Timing
8.9.15.1.1.1 General-Purpose Output Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
MAX
13(1)
13(1)
22.5
UNIT
ns
tr(GPO)
tf(GPO)
fGPO
Rise time, GPIO switching low to high
Fall time, GPIO switching high to low
Toggling frequency
All GPIOs
All GPIOs
ns
MHz
(1) Rise time and fall time vary with electrical loading on I/O pins. Values given in Section 8.9.15.1.1.1 are applicable for a 40-pF load on
I/O pins.
GPIO
t
r(GPO)
t
f(GPO)
Figure 8-56. General-Purpose Output Timing
Copyright © 2021 Texas Instruments Incorporated
154 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.15.1.2 GPIO Input Timing
8.9.15.1.2.1 General-Purpose Input Timing Requirements
MIN
1tc(SCO)
MAX
UNIT
cycles
cycles
cycles
QUALPRD = 0
tw(SP)
Sampling period
QUALPRD ≠ 0
2tc(SCO) * QUALPRD
tw(SP) * (n(1) – 1)
2tc(SCO)
tw(IQSW)
Input qualifier sampling window
Pulse duration, GPIO low/high
Synchronous mode
With input qualifier
(2)
tw(GPI)
tw(IQSW) + tw(SP) + 1tc(SCO)
(1) "n" represents the number of qualification samples as defined by GPxQSELn register.
(2) For tw(GPI), pulse width is measured from VIL to VIL for an active-low signal and VIH to VIH for an active-high signal.
(A)
GPIO Signal
GPxQSELn = 1,0 (6 samples)
1
1
0
0
0
0
0
0
0
1
0
0
0
1
1
1
1
1
1
1
1
1
tw(SP)
Sampling Period determined
by GPxCTRL[QUALPRD](B)
tw(IQSW)
[(SYSCLKOUT cycle * 2 * QUALPRD) * 5(C)
]
Sampling Window
SYSCLKOUT
QUALPRD = 1
(SYSCLKOUT/2)
(D)
Output From
Qualifier
A. This glitch will be ignored by the input qualifier. The QUALPRD bit field specifies the qualification sampling period. The QUALPRD bit
field value can vary from 00 to 0xFF. If QUALPRD = 00, then the sampling period is one SYSCLKOUT cycle. For any other value "n", the
qualification sampling period in 2n SYSCLKOUT cycles (that is, at every 2n SYSCLKOUT cycles, the GPIO pin will be sampled).
B. The qualification period selected through the GPxCTRL register applies to groups of eight GPIO pins.
C. The qualification block can take either three or six samples. The GPxQSELn Register selects which sample mode is used.
D. In the example shown, for the qualifier to detect the change, the input should be stable for 10 SYSCLKOUT cycles or greater. In other
words, the inputs should be stable for (5 × QUALPRD × 2) SYSCLKOUT cycles. This would ensure five sampling periods for detection to
occur. Because external signals are driven asynchronously, an 13-SYSCLKOUT-wide pulse ensures reliable recognition.
Figure 8-57. Sampling Mode
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 155
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.15.1.3 Sampling Window Width for Input Signals
The following section summarizes the sampling window width for input signals for various input qualifier
configurations.
Sampling frequency denotes how often a signal is sampled with respect to SYSCLKOUT.
Sampling frequency = SYSCLKOUT/(2 × QUALPRD), if QUALPRD ≠ 0
Sampling frequency = SYSCLKOUT, if QUALPRD = 0
Sampling period = SYSCLKOUT cycle × 2 × QUALPRD, if QUALPRD ≠ 0
In the preceding samples, SYSCLKOUT cycle indicates the time period of SYSCLKOUT.
Sampling period = SYSCLKOUT cycle, if QUALPRD = 0
In a given sampling window, either three or six samples of the input signal are taken to determine the validity of
the signal. This is determined by the value written to GPxQSELn register.
Case 1:
Qualification using three samples
Sampling window width = (SYSCLKOUT cycle × 2 × QUALPRD) × 2, if QUALPRD ≠ 0
Sampling window width = (SYSCLKOUT cycle) × 2, if QUALPRD = 0
Case 2:
Qualification using six samples
Sampling window width = (SYSCLKOUT cycle × 2 × QUALPRD) × 5, if QUALPRD ≠ 0
Sampling window width = (SYSCLKOUT cycle) × 5, if QUALPRD = 0
SYSCLK
GPIOxn
tw(GPI)
Figure 8-58. General-Purpose Input Timing
Copyright © 2021 Texas Instruments Incorporated
156 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
VDDIO
> 1 MS
2 pF
VSS
VSS
Figure 8-59. Input Resistance Model for a GPIO Pin With an Internal Pullup
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 157
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.15.1.4 Low-Power Mode Wakeup Timing
Section 8.9.15.1.4.1 shows the timing requirements, Section 8.9.15.1.4.2 shows the switching characteristics,
and Figure 8-60 shows the timing diagram for IDLE mode.
8.9.15.1.4.1 IDLE Mode Timing Requirements
MIN(1)
2tc(SCO)
MAX
UNIT
Without input qualifier
With input qualifier
tw(WAKE-INT)
Pulse duration, external wake-up signal
cycles
5tc(SCO) + tw(IQSW)
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
8.9.15.1.4.2 IDLE Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted)(1)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
Delay time, external wake signal to program execution resume (2)
cycles
•
•
Wake up from flash
Flash module in active state
Without input qualifier
With input qualifier
Without input qualifier
With input qualifier
Without input qualifier
With input qualifier
20tc(SCO)
cycles
cycles
cycles
–
20tc(SCO) + tw(IQSW)
1050tc(SCO)
td(WAKE-IDLE)
Wake up from flash
Flash module in sleep state
–
1050tc(SCO) + tw(IQSW)
20tc(SCO)
•
Wake up from SARAM
20tc(SCO) + tw(IQSW)
(1) For an explanation of the input qualifier parameters, see Section 8.9.15.1.2.1.
(2) This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. Execution of an ISR (triggered
by the wake-up signal) involves additional latency.
t
d(WAKE−IDLE)
Address/Data
(internal)
XCLKOUT
t
w(WAKE−INT)
WAKE INT(A)(B)
A. WAKE INT can be any enabled interrupt, WDINT or XRS. After the IDLE instruction is executed, a delay of five OSCCLK cycles
(minimum) is needed before the wake-up signal could be asserted.
B. From the time the IDLE instruction is executed to place the device into low-power mode (LPM), wakeup should not be initiated until at
least four OSCCLK cycles have elapsed.
Figure 8-60. IDLE Entry and Exit Timing
Copyright © 2021 Texas Instruments Incorporated
158 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.15.1.4.3 STANDBY Mode Timing Requirements
MIN MAX
3tc(OSCCLK)
UNIT
Without input qualification
Pulse duration, external
tw(WAKE-INT)
cycles
(2 + QUALSTDBY) *
tc(OSCCLK)
With input qualification(1)
wake-up signal
(1) QUALSTDBY is a 6-bit field in the LPMCR0 register.
8.9.15.1.4.4 STANDBY Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
Delay time, IDLE instruction
executed to XCLKOUT low
td(IDLE-XCOL)
32tc(SCO)
45tc(SCO) cycles
cycles
Delay time, external wake signal to program execution
resume(1)
•
Wake up from flash
Flash module in active state
Without input qualifier
With input qualifier
Without input qualifier
With input qualifier
Without input qualifier
With input qualifier
100tc(SCO)
cycles
–
100tc(SCO) + tw(WAKE-INT)
td(WAKE-STBY)
•
Wake up from flash
Flash module in sleep state
1125tc(SCO)
1125tc(SCO) + tw(WAKE-INT)
100tc(SCO)
cycles
cycles
–
•
Wake up from SARAM
100tc(SCO) + tw(WAKE-INT)
(1) This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. Execution of an ISR (triggered
by the wake-up signal) involves additional latency.
(C)
(F)
(A)
(B)
(D)(E)
(G)
Device
Status
STANDBY
STANDBY
Normal Execution
Flushing Pipeline
Wake-up
Signal(H)
t
w(WAKE-INT)
t
d(WAKE-STBY)
X1/X2 or
XCLKIN
XCLKOUT
t
d(IDLE−XCOL)
A. IDLE instruction is executed to put the device into STANDBY mode.
B. The PLL block responds to the STANDBY signal. SYSCLKOUT is held for the number of cycles indicated below before being turned off:
•
•
•
16 cycles, when DIVSEL = 00 or 01
32 cycles, when DIVSEL = 10
64 cycles, when DIVSEL = 11
This delay enables the CPU pipeline and any other pending operations to flush properly.
C. Clock to the peripherals are turned off. However, the PLL and watchdog are not shut down. The device is now in STANDBY mode. After
the IDLE instruction is executed, a delay of five OSCCLK cycles (minimum) is needed before the wake-up signal could be asserted.
D. The external wake-up signal is driven active.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 159
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
E. The wake-up signal fed to a GPIO pin to wake up the device must meet the minimum pulse width requirement. Furthermore, this signal
must be free of glitches. If a noisy signal is fed to a GPIO pin, the wake-up behavior of the device will not be deterministic and the device
may not exit low-power mode for subsequent wake-up pulses.
F. After a latency period, the STANDBY mode is exited.
G. Normal execution resumes. The device will respond to the interrupt (if enabled).
H. From the time the IDLE instruction is executed to place the device into low-power mode (LPM), wakeup should not be initiated until at
least four OSCCLK cycles have elapsed.
Figure 8-61. STANDBY Entry and Exit Timing Diagram
8.9.15.1.4.5 HALT Mode Timing Requirements
MIN
toscst + 2tc(OSCCLK)
toscst + 8tc(OSCCLK)
MAX
UNIT
cycles
cycles
tw(WAKE-GPIO)
tw(WAKE-XRS)
Pulse duration, GPIO wake-up signal
Pulse duration, XRS wake-up signal
8.9.15.1.4.6 HALT Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
MAX
45tc(SCO)
1
UNIT
cycles
ms
td(IDLE-XCOL)
tp
Delay time, IDLE instruction executed to XCLKOUT low
PLL lock-up time
32tc(SCO)
Delay time, PLL lock to program execution resume
•
Wake up from flash
– Flash module in sleep state
1125tc(SCO)
cycles
td(WAKE-HALT)
•
Wake up from SARAM
35tc(SCO)
cycles
(C)
(F)
(A)
(H)
(B)
(G)
(D)(E)
Device
Status
HALT
HALT
Flushing Pipeline
PLL Lock-up Time
Normal
Execution
Wake-up Latency
GPIOn(I)
t
)
d(WAKE−HALT
t
w(WAKE-GPIO)
tp
X1/X2 or
XCLKIN
Oscillator Start-up Time
XCLKOUT
t
d(IDLE−XCOL)
A. IDLE instruction is executed to put the device into HALT mode.
B. The PLL block responds to the HALT signal. SYSCLKOUT is held for the number of cycles indicated below before oscillator is turned off
and the CLKIN to the core is stopped:
•
•
•
16 cycles, when DIVSEL = 00 or 01
32 cycles, when DIVSEL = 10
64 cycles, when DIVSEL = 11
This delay enables the CPU pipeline and any other pending operations to flush properly.
C. Clocks to the peripherals are turned off and the PLL is shut down. If a quartz crystal or ceramic resonator is used as the clock source,
the internal oscillator is shut down as well. The device is now in HALT mode and consumes absolute minimum power. It is possible to
keep the zero-pin internal oscillators (INTOSC1 and INTOSC2) and the watchdog alive in HALT mode. This is done by writing to the
appropriate bits in the CLKCTL register. After the IDLE instruction is executed, a delay of five OSCCLK cycles (minimum) is needed
before the wake-up signal could be asserted.
Copyright © 2021 Texas Instruments Incorporated
160 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
D. When the GPIOn pin (used to bring the device out of HALT) is driven low, the oscillator is turned on and the oscillator wake-up sequence
is initiated. The GPIO pin should be driven high only after the oscillator has stabilized. This enables the provision of a clean clock signal
during the PLL lock sequence. Because the falling edge of the GPIO pin asynchronously begins the wake-up procedure, care should be
taken to maintain a low-noise environment before entering and during HALT mode.
E. The wake-up signal fed to a GPIO pin to wake up the device must meet the minimum pulse width requirement. Furthermore, this signal
must be free of glitches. If a noisy signal is fed to a GPIO pin, the wake-up behavior of the device will not be deterministic and the device
may not exit low-power mode for subsequent wake-up pulses.
F. Once the oscillator has stabilized, the PLL lock sequence is initiated, which takes 1 ms.
G. When CLKIN to the core is enabled, the device will respond to the interrupt (if enabled), after a latency. The HALT mode is now exited.
H. Normal operation resumes.
I. From the time the IDLE instruction is executed to place the device into low-power mode (LPM), wakeup should not be initiated until at
least four OSCCLK cycles have elapsed.
Figure 8-62. HALT Mode Wakeup Using GPIOn
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 161
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
8.9.16 Universal Serial Bus (USB)
8.9.16.1 USB Electrical Data/Timing
8.9.16.1.1 USB Input Ports DP and DM Timing Requirements
VCC
MIN
0.8
MAX
UNIT
V
V(CM)
Z(IN)
VCRS
VIL
Differential input common mode range
Input impedance
2.5
300
1.3
kΩ
V
Crossover voltage
2.0
Static SE input logic-low level
Static SE input logic-high level
Differential input voltage
0.8
V
VIH
2.0
0.2
V
VDI
V
8.9.16.1.2 USB Output Ports DP and DM Switching Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
D+, D– single-ended
D+, D– single-ended
D+, D– impedance
TEST CONDITIONS
VCC
MIN
MAX
UNIT
V
VOH
USB 2.0 load conditions
2.8
0
3.6
0.3
50
VOL
USB 2.0 load conditions
V
Z(DRV)
28
Ω
Full speed, differential, CL = 50 pF,
10%/90%, Rpu on D+
tr
tf
Rise time
Fall time
4
4
20
20
ns
ns
Full speed, differential, CL = 50 pF,
10%/90%, Rpu on D+
Copyright © 2021 Texas Instruments Incorporated
162 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
9 Applications, Implementation, and Layout
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
9.1 TI Reference Design
The TI Reference Design Library is a robust reference design library spanning analog, embedded processor,
and connectivity. Created by TI experts to help you jump start your system design, all reference designs include
schematic or block diagrams, BOMs, and design files to speed your time to market. Search and download
designs at the Select TI reference designs page.
Digitally Controlled Non-Isolated DC/DC Buck Converter Reference Design
This design implements a non-isolated DC/DC buck converter that is digitally controlled using a C2000
microcontroller. The main purpose of this design is to evaluate the powerSUITE Digital Power Software tools.
The design consists of two separate boards: 1) Digital Power BoosterPack™ Plug-in Module and 2) C2000
F28069M LaunchPad™ Development Kit or C2000 F28377S LaunchPad Development Kit.
672W Highly Integrated Reference Design for Automotive Bidirectional 48V-12V Converter
Today's automotive power consumption is 3KW, which will increase to 10KW in the next 5 years. A 12-V battery
is unable to provide that much power. The 48-12V bidirectional convertor provides a high-power requirement
solution with two phases, each capable of running 28 A. This solution allows bidirectional current control of both
phases using a C2000 control stick and firmware OCP and OVP. The 48-12V bidirectional converter removes the
voltage conditioner need and distributes loads more evenly. The 48-V battery is used to power high-torque
motors and other high-power components, such as A/C compressors and EPS, with no change to 12-V battery
loads.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 163
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
10 Device and Documentation Support
10.1 Device and Development Support Tool Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
TMS320™ MCU devices and support tools. Each TMS320 MCU commercial family member has one of three
prefixes: TMX, TMP, or TMS (for example, TMS320F28069). Texas Instruments recommends two of three
possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages
of product development from engineering prototypes (with TMX for devices and TMDX for tools) to fully qualified
production devices/tools (with TMS for devices and TMDS for tools).
Device development evolutionary flow:
TMX
TMP
Experimental device that is not necessarily representative of the final device's electrical specifications
Final silicon die that conforms to the device's electrical specifications but has not completed quality and reliability
verification
TMS
Fully qualified production device
Support tool development evolutionary flow:
TMDX
TMDS
Development-support product that has not yet completed Texas Instruments internal qualification testing
Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped against the following disclaimer:
"Developmental product is intended for internal evaluation purposes."
TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI's standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, PZP) and temperature range (for example, S). Figure 10-1 provides a legend for reading the
complete device name for any family member.
For device part numbers and further ordering information, see the TI website (www.ti.com) or contact your TI
sales representative.
For additional description of the device nomenclature markings on the die, see the TMS320F2806x MCUs
Silicon Errata.
Copyright © 2021 Texas Instruments Incorporated
164 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
A. USB is present on TMS320F2806xU, TMS320F2806xM, and TMS320F2806xF devices.
B. TMS320F2806xM devices are InstaSPIN-MOTION-enabled MCUs. TMS320F2806xF devices are InstaSPIN-FOC-enabled MCUs. For
more information, see Section 10.3 for a list of InstaSPIN Technical Reference Manuals.
C. For more information on peripheral, temperature, and package availability for a specific device, see Table 5-1.
Figure 10-1. Device Nomenclature
10.2 Tools and Software
TI offers an extensive line of development tools. Some of the tools and software to evaluate the performance of
the device, generate code, and develop solutions are listed below. To view all available tools and software for
C2000™ real-time control MCUs, visit the C2000 real-time control MCUs – Design & development page.
Development Tools
C2000 F28069M LaunchPad™ development kit
LAUNCHXL-F28069M is a low cost evaluation and development tool for the F2806x series as well as the
InstaSPIN-FOC and InstaSPIN-MOTION enabled F2806x series in the TI MCU LaunchPad ecosystem which is
compatible with various plug-on BoosterPacks. This extended version of the LaunchPad supports the connection
of two BoosterPacks. The LaunchPad provides a standardized and easy to use platform to use while developing
your next application.
F28069 controlCARD
The C2000 controlCARDs from Texas Instruments are ideal products for OEMs to use for initial software
development and short-run builds for system prototypes, test stands, and many other projects that require easy
access to high-performance controllers. The controlCARDs are complete board-level modules that use an
industry-standard DIMM form factor to provide a low-profile, single-board controller solution. All of the C2000
controlCARDs use the same 100-pin connector footprint to provide the analog and digital I/Os onboard controller
and are completely interchangeable. The host system must provide only a single 5-V power rail to the
controlCARD for it to function fully.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 165
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
F28069 Experimenter Kit
The C2000 experimenter kits from Texas Instruments are ideal products for OEMs to use for initial device
exploration and testing. The F28069 Experimenter Kit has a docking station that features onboard USB JTAG
emulation, access to all controlCARD signals, breadboard areas, and RS-232 and JTAG connectors. Each kit
contains an F28069 controlCARD. The controlCARD is a complete board-level module that uses an industry-
standard DIMM form factor to provide a low-profile, single-board controller solution. The kit is complete with
Code Composer Studio IDE and USB cable.
Software Tools
C2000Ware for C2000 MCUs
C2000Ware for C2000™ microcontrollers is a cohesive set of development software and documentation
designed to minimize software development time. From device-specific drivers and libraries to device peripheral
examples, C2000Ware provides a solid foundation to begin development and evaluation of your product.
Code Composer Studio™ (CCS) Integrated Development Environment (IDE) for C2000 Microcontrollers
Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and
Embedded Processors portfolio. CCS comprises a suite of tools used to develop and debug embedded
applications. It includes an optimizing C/C++ compiler, source code editor, project build environment, debugger,
profiler, and many other features. The intuitive IDE provides a single user interface taking the user through each
step of the application development flow. Familiar tools and interfaces let users get started faster than ever
before. CCS combines the advantages of the Eclipse software framework with advanced embedded debug
capabilities from TI resulting in a compelling feature-rich development environment for embedded developers.
Pin Mux Tool
The Pin Mux Utility is a software tool which provides a Graphical User Interface for configuring pin multiplexing
settings, resolving conflicts and specifying I/O cell characteristics for TI MPUs.
UniFlash Standalone Flash Tool
UniFlash is a standalone tool used to program on-chip flash memory through a GUI, command line, or scripting
interface.
Models
Various models are available for download from the product Tools & Software pages. These include I/O Buffer
Information Specification (IBIS) Models and Boundary-Scan Description Language (BSDL) Models. To view all
available models, visit the Models section of the Tools & Software page for each device.
Training
To help assist design engineers in taking full advantage of the C2000 microcontroller features and performance,
TI has developed a variety of training resources. Utilizing the online training materials and downloadable hands-
on workshops provides an easy means for gaining a complete working knowledge of the C2000 microcontroller
family. These training resources have been designed to decrease the learning curve, while reducing
development time, and accelerating product time to market. For more information on the various training
resources, visit the C2000™ real-time control MCUs – Support & training site.
Specific TMS320F2806x hands-on training resources can be found at C2000™ MCU Device Workshops.
Copyright © 2021 Texas Instruments Incorporated
166 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
10.3 Documentation Support
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper-
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
The current documentation that describes the processor, related peripherals, and other technical collateral is
listed below.
Errata
TMS320F2806x MCUs Silicon Errata describes known advisories on silicon and provides workarounds.
InstaSPIN Technical Reference Manuals
InstaSPIN-FOC™ and InstaSPIN-MOTION™ User's Guide describes the InstaSPIN-FOC and InstaSPIN-
MOTION devices.
TMS320F28069F, TMS320F28068F, TMS320F28062F InstaSPIN-FOC™ Software Technical Reference Manual
describes the TMS320F28069F, TMS320F28068F, and TMS320F28062F InstaSPIN-FOC™ software.
TMS320F28069M, TMS320F28068M InstaSPIN-MOTION™ Software Technical Reference Manual describes
the TMS320F28069M and TMS320F28068M InstaSPIN-MOTION™ software.
CPU User's Guides
TMS320C28x CPU and Instruction Set Reference Guide describes the central processing unit (CPU) and the
assembly language instructions of the TMS320C28x fixed-point digital signal processors (DSPs). This reference
guide also describes emulation features available on these DSPs.
Peripheral Guides and Technical Reference Manuals
C2000 Real-Time Control Peripherals Reference Guide describes the peripheral reference guides of the 28x
digital signal processors (DSPs).
TMS320x2806x Technical Reference Manual details the integration, the environment, the functional description,
and the programming models for each peripheral and subsystem in the device.
Tools Guides
TMS320C28x Assembly Language Tools v19.6.0.STS User's Guide describes the assembly language tools
(assembler and other tools used to develop assembly language code), assembler directives, macros, common
object file format, and symbolic debugging directives for the TMS320C28x device.
TMS320C28x Optimizing C/C++ Compiler v19.6.0.STS User's Guide describes the TMS320C28x C/C++
compiler. This compiler accepts ANSI standard C/C++ source code and produces TMS320 DSP assembly
language source code for the TMS320C28x device.
Application Reports
Semiconductor Packing Methodology describes the packing methodologies employed to prepare semiconductor
devices for shipment to end users.
Calculating Useful Lifetimes of Embedded Processors provides a methodology for calculating the useful lifetime
of TI embedded processors (EPs) under power when used in electronic systems. It is aimed at general
engineers who wish to determine if the reliability of the TI EP meets the end system reliability requirement.
An Introduction to IBIS (I/O Buffer Information Specification) Modeling discusses various aspects of IBIS
including its history, advantages, compatibility, model generation flow, data requirements in modeling the input/
output structures and future trends.
Serial Flash Programming of C2000™ Microcontrollers discusses using a flash kernel and ROM loaders for
serial programming a device.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 167
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
10.4 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
10.5 Trademarks
PowerPAD™, InstaSPIN-MOTION™, InstaSPIN-FOC™, TMS320C2000™, C2000™, FAST™, BoosterPack™,
LaunchPad™, TMS320™, Code Composer Studio™, and TI E2E™ are trademarks of Texas Instruments.
SpinTAC™ are trademarks of LineStream Technologies, Inc.
I2C-bus® is a registered trademark of NXP B.V. Corporation.
All trademarks are the property of their respective owners.
10.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
10.7 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2021 Texas Instruments Incorporated
168 Submit Document Feedback
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
TMS320F28069, TMS320F28069M, TMS320F28069F, TMS320F28068M, TMS320F28068F
TMS320F28067, TMS320F28066, TMS320F28065, TMS320F28064, TMS320F28063
TMS320F28062, TMS320F28062F
SPRS698I – NOVEMBER 2010 – REVISED FEBRUARY 2021
www.ti.com
11 Mechanical, Packaging, and Orderable Information
11.1 Packaging Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
For packages with a thermal pad, the MECHANICAL DATA figure shows a generic thermal pad without
dimensions. For the actual thermal pad dimensions that are applicable to this device, see the THERMAL PAD
MECHANICAL DATA figure.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback 169
Product Folder Links: TMS320F28069 TMS320F28069M TMS320F28069F TMS320F28068M
TMS320F28068F TMS320F28067 TMS320F28066 TMS320F28065 TMS320F28064 TMS320F28063
TMS320F28062 TMS320F28062F
PACKAGE OPTION ADDENDUM
www.ti.com
16-Feb-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
PFP
PN
Qty
(1)
(2)
(3)
(4/5)
(6)
TMS320F28062FPFPQ
TMS320F28062FPNT
TMS320F28062FPZT
TMS320F28062PFPQ
TMS320F28062PFPQR
TMS320F28062PFPS
TMS320F28062PNT
TMS320F28062PZPQ
TMS320F28062PZPS
TMS320F28062PZT
TMS320F28062PZTR
TMS320F28062UPNT
TMS320F28062UPZT
TMS320F28063PNT
TMS320F28063PZT
TMS320F28064PZT
TMS320F28065PFPS
ACTIVE
HTQFP
LQFP
80
80
96
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 125
-40 to 105
-40 to 105
-40 to 125
-40 to 125
-40 to 125
-40 to 105
-40 to 125
-40 to 125
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 125
F28062FPFPQ
TMS320
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
119
90
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
F28062FPNT
TMS320
LQFP
PZ
100
80
F28062FPZT
TMS320
HTQFP
HTQFP
HTQFP
LQFP
PFP
PFP
PFP
PN
96
F28062PFPQ
TMS320
80
1000 RoHS & Green
F28062PFPQ
TMS320
80
96
119
90
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
F28062PFPS
TMS320
80
320F28062PNT
TMS
HTQFP
HTQFP
LQFP
PZP
PZP
PZ
100
100
100
100
80
F28062PZPQ
TMS320
90
F28062PZPS
TMS320
90
320F28062PZT
TMS
LQFP
PZ
1000 RoHS & Green
320F28062PZT
TMS
LQFP
PN
119
90
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
320F28062UPNT
TMS
LQFP
PZ
100
80
F28062UPZT
TMS320
LQFP
PN
119
90
320F28063PNT
TMS
LQFP
PZ
100
100
80
320F28063PZT
TMS
LQFP
PZ
90
320F28064PZT
TMS
HTQFP
PFP
96
F28065PFPS
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
16-Feb-2021
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TMS320
TMS320F28065PNT
TMS320F28065PZPQ
TMS320F28065PZPS
TMS320F28065PZT
TMS320F28065UPZPS
TMS320F28065UPZT
TMS320F28066PFPQ
TMS320F28066PFPS
TMS320F28066PNT
TMS320F28066PZPQ
TMS320F28066PZPS
TMS320F28066PZT
TMS320F28067PFPS
TMS320F28067PNT
TMS320F28067PZPQ
TMS320F28067PZPS
TMS320F28067PZT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
LQFP
HTQFP
HTQFP
LQFP
PN
PZP
PZP
PZ
80
100
100
100
100
100
80
119
90
90
90
90
90
96
96
119
90
90
90
96
119
90
90
90
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 105
-40 to 125
-40 to 125
-40 to 105
-40 to 125
-40 to 105
-40 to 125
-40 to 125
-40 to 105
-40 to 125
-40 to 125
-40 to 105
-40 to 125
-40 to 105
-40 to 125
-40 to 125
-40 to 105
F28065PNT
TMS320
F28065PZPQ
TMS320
F28065PZPS
TMS320
320F28065PZT
TMS
HTQFP
LQFP
PZP
PZ
F28065UPZPS
TMS320
F28065UPZT
TMS320
HTQFP
HTQFP
LQFP
PFP
PFP
PN
F28066PFPQ
TMS320
80
F28066PFPS
TMS320
80
320F28066PNT
TMS
HTQFP
HTQFP
LQFP
PZP
PZP
PZ
100
100
100
80
F28066PZPQ
TMS320
F28066PZPS
TMS320
320F28066PZT
TMS
HTQFP
LQFP
PFP
PN
F28067PFPS
TMS320
80
320F28067PNT
TMS
HTQFP
HTQFP
LQFP
PZP
PZP
PZ
100
100
100
F28067PZPQ
TMS320
F28067PZPS
TMS320
320F28067PZT
TMS
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
16-Feb-2021
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
119
90
(1)
(2)
(3)
(4/5)
(6)
TMS320F28068FPNT
TMS320F28068FPZT
TMS320F28068MPNT
TMS320F28068MPZT
TMS320F28069FPFPQ
TMS320F28069FPNT
TMS320F28069FPZPQ
TMS320F28069FPZT
TMS320F28069FPZTR
TMS320F28069MPFPQ
TMS320F28069MPNT
TMS320F28069MPZPQ
TMS320F28069MPZT
TMS320F28069PFPQ
TMS320F28069PFPS
TMS320F28069PNT
TMS320F28069PZA
TMS320F28069PZPQ
ACTIVE
LQFP
LQFP
PN
80
100
80
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 125
-40 to 105
-40 to 125
-40 to 105
-40 to 105
-40 to 125
-40 to 105
-40 to 125
-40 to 105
-40 to 125
-40 to 125
-40 to 125
-40 to 85
F28068FPNT
TMS320
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PZ
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
F28068FPZT
TMS320
LQFP
PN
119
90
F28068MPNT
TMS320
LQFP
PZ
100
80
F28068MPZT
TMS320
HTQFP
LQFP
PFP
PN
96
F28069FPFPQ
TMS320
80
119
90
F28069FPNT
TMS320
HTQFP
LQFP
PZP
PZ
100
100
100
80
F28069FPZPQ
TMS320
90
F28069FPZT
TMS320
LQFP
PZ
1000 RoHS & Green
F28069FPZT
TMS320
HTQFP
LQFP
PFP
PN
96
119
90
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
F28069MPFPQ
TMS320
80
F28069MPNT
TMS320
HTQFP
LQFP
PZP
PZ
100
100
80
F28069MPZPQ
TMS320
90
F28069MPZT
TMS320
HTQFP
HTQFP
LQFP
PFP
PFP
PN
96
F28069PFPQ
TMS320
80
96
F28069PFPS
TMS320
80
119
90
320F28069PNT
TMS
LQFP
PZ
100
100
320F28069PZA
TMS
HTQFP
PZP
90
-40 to 125
F28069PZPQ
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
16-Feb-2021
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TMS320
TMS320F28069PZPS
TMS320F28069PZT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
HTQFP
LQFP
PZP
PZ
100
100
80
90
90
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 125
-40 to 105
-40 to 125
-40 to 105
-40 to 125
-40 to 105
F28069PZPS
TMS320
320F28069PZT
TMS
TMS320F28069UPFPS
TMS320F28069UPNT
TMS320F28069UPZPS
TMS320F28069UPZT
HTQFP
LQFP
PFP
PN
96
F28069UPFPS
TMS320
80
119
90
F28069UPNT
TMS320
HTQFP
LQFP
PZP
PZ
100
100
F28069UPZPS
TMS320
90
F28069UPZT
TMS320
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com
16-Feb-2021
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TMS320F28062, TMS320F28062-Q1, TMS320F28062F, TMS320F28062F-Q1, TMS320F28065, TMS320F28065-Q1, TMS320F28066,
TMS320F28066-Q1, TMS320F28067, TMS320F28067-Q1, TMS320F28069, TMS320F28069-Q1, TMS320F28069F, TMS320F28069F-Q1, TMS320F28069M, TMS320F28069M-
Q1 :
Catalog: TMS320F28062, TMS320F28062F, TMS320F28065, TMS320F28066, TMS320F28067, TMS320F28069, TMS320F28069F, TMS320F28069M
•
Automotive: TMS320F28062-Q1, TMS320F28062F-Q1, TMS320F28065-Q1, TMS320F28066-Q1, TMS320F28067-Q1, TMS320F28069-Q1, TMS320F28069F-Q1,
TMS320F28069M-Q1
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Jan-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TMS320F28062PFPQR HTQFP
TMS320F28069FPZTR LQFP
PFP
PZ
80
1000
1000
330.0
330.0
24.4
32.4
15.0
16.9
15.0
16.9
1.5
2.0
20.0
24.0
24.0
32.0
Q2
Q2
100
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Jan-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TMS320F28062PFPQR
TMS320F28069FPZTR
HTQFP
LQFP
PFP
PZ
80
1000
1000
367.0
367.0
367.0
367.0
55.0
55.0
100
Pack Materials-Page 2
www.ti.com
MECHANICAL DATA
MTQF010A – JANUARY 1995 – REVISED DECEMBER 1996
PN (S-PQFP-G80)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
60
M
0,08
41
61
40
0,13 NOM
80
21
1
20
Gage Plane
9,50 TYP
0,25
12,20
SQ
11,80
0,05 MIN
0°–7°
14,20
SQ
13,80
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040135 /B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTQF013A – OCTOBER 1994 – REVISED DECEMBER 1996
PZ (S-PQFP-G100)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
75
M
0,08
51
50
76
26
100
0,13 NOM
1
25
12,00 TYP
Gage Plane
14,20
SQ
13,80
0,25
16,20
SQ
0,05 MIN
0°–7°
15,80
1,45
1,35
0,75
0,45
Seating Plane
0,08
1,60 MAX
4040149/B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明