TPA6013A4PWP [TI]
3-W STEREO AUDIO POWER AMPLIFIER WITH ADVANCED DC VOLUME CONTROL; 具有高级DC音量控制的3W立体声音频功率放大器型号: | TPA6013A4PWP |
厂家: | TEXAS INSTRUMENTS |
描述: | 3-W STEREO AUDIO POWER AMPLIFIER WITH ADVANCED DC VOLUME CONTROL |
文件: | 总28页 (文件大小:499K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
3-W STEREO AUDIO POWER AMPLIFIER
WITH ADVANCED DC VOLUME CONTROL
Check for Samples :TPA6013A4
1
FEATURES
DESCRIPTION
2
•
Advanced 32-Steps DC Volume Control
–
–
–
–
Steps from –40 to 18 dB
Fade Mode
The TPA6013A4 is a stereo audio power amplifier
that drives 3 W/channel of continuous RMS power
into
a 3-Ω load. Advanced dc volume control
Maximum Volume Setting for SE Mode
minimizes external components and allows BTL
(speaker) volume control and SE (headphone)
volume control. Notebook and pocket PCs benefit
from the integrated feature set that minimizes
external components without sacrificing functionality.
Adjustable SE Volume Control
Referenced to BTL Volume Control
•
•
•
•
3 W Into 3-Ω Speakers
Stereo Input MUX
Headphone Mode
To simplify design, the speaker volume level is
adjusted by applying a dc voltage to the VOLUME
terminal. Likewise, the delta between speaker volume
and headphone volume can be adjusted by applying
a dc voltage to the SEDIFF terminal. To avoid an
unexpected high volume level through the
headphones, a third terminal, SEMAX, limits the
headphone volume level when a dc voltage is
Pin-to-pin compatible with TPA6011A4 and
TPA6012A4
•
24-pin PowerPAD™ Package (PWP)
APPLICATIONS
•
•
•
Notebook PC
LCD Monitors
Pocket PC
applied. Finally, to ensure
a smooth transition
between active and shutdown modes, a fade mode
ramps the volume up and down.
APPLICATION CIRCUIT
DC VOLUME CONTROL
GAIN (BTL)
vs
VOLUME VOLTAGE
Right
Speaker
VDD
24
23
CC
ROUT+
SE/BTL
1
PGND
20
100 kW
100 kW
Volume Up
Volume Down
2
10
CS
ROUT−
22
0
−10
−20
−30
−40
−50
−60
HP/LINE
3
1 kW
PVDD
Power Supply
Right HP
Ci
4
5
6
21
20
RHPIN
RLINEIN
RIN
VOLUME
SEDIFF
SEMAX
Audio Source
Ci
In From DAC
or
Potentiometer
(DC Voltage)
Right Line
Audio Source
Ci
19
VDD
CS
Headphones
7
8
18
17
VDD
LIN
AGND
C(BYP)
Ci
−70
−80
−90
VDD = 5.0 V
BYPASS
BTL Output
RL = No Load
1 kW
Ci
CC
9
16
15
Left Line
Audio Source
LLINEIN
LHPIN
FADE
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Ci
10
Volume [Pin 21] − V
Left HP
Audio Source
System Control
SHUTDOWN
11
12
14
13
PVDD
Power Supply
Left
Speaker
LOUT+
PGND
CS
LOUT−
S001
Figure 1. Application Circuit and DC Volume Control
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
AVAILABLE OPTIONS
PACKAGE
TA
(1)
24-PIN TSSOP (PWP)
–40°C to 85°C
TPA6013A4PWP
(1) The PWP package is available taped and reeled. To order a taped
and reeled part, add the suffix R to the part number
(e.g., TPA6013A4PWPR).
LEAD (PB-FREE) ORDERING INFORMATION
(1)
(2)
ORDERABLE DEVICE
STATUS
ECO-STATUS
TPA6013A4PWPG4
TPA6013A4PWPRG4
Active
Pb-Free
and Green
Active
(1) The marketing status values are defined as follows:
(a) ACTIVE: This device recommended for new designs.
(b) LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
(c) NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using
this part in a new design.
(d) PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
(e) OBSOLETE: TI has discontinued production of the device.
(2) Eco-Status Information – Additional details including specific material content can be accessed at www.ti.com/leadfree
(a) N/A: Not yet available Lead (Pb)-Free, for estimated conversion dates go to www.ti.com/leadfree.
(b) Pb-Free: TI defines "Lead (Pb)-Free" or "Pb-Free" to mean RoHS compatible, including a lead concentration that does not exceed
0.1% of total product weight, and, if designed to be soldered, suitable for use in specified lead-free soldering processes.
(c) Green: TI devices "Green" to mean Lead (Pb)-Free and in addition, uses package materials that do not contain halogens, including
bromine (Br), or antimony (Sb) above 0.1% of total product weight.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
UNIT
VSS
VI
Supply voltage, VDD, PVDD
Input voltage
–0.3 V to 6 V
–0.3 V to VDD+0.3 V
See Dissipation Rating Table
–40°C to 85°C
Continuous total power dissipation
Operating free-air temperature range
Operating junction temperature range
Storage temperature range
TA
TJ
–40°C to 150°C
Tstg
–65°C to 150°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
T
A ≤ 25°C
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
TA = 85°C
POWER RATING
PACKAGE
POWER RATING
POWER RATING
PWP
2.7 mW
21.8 mW/°C
1.7 W
1.4 W
2
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
RECOMMENDED OPERATING CONDITIONS
MIN
4.0
MAX
UNIT
V
VSS
VIH
Supply voltage, VDD, PVDD
High-level input voltage
5.5
SE/BTL, HP/LINE, FADE
SHUTDOWN
0.8 × VDD
2
V
V
SE/BTL, HP/LINE, FADE
SHUTDOWN
0.6 × VDD
0.8
V
VIL
TA
Low-level input voltage
V
Operating free-air temperature
–40
85
°C
ELECTRICAL CHARACTERISTICS
TA = 25°C, VDD = PVDD = 5.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP
MAX UNIT
VDD = 5.5 V, Gain = 0 dB, SE/BTL = 0 V
VDD = 5.5 V, Gain = 18 dB, SE/BTL = 0 V
VDD = PVDD = 4.0 V to 5.5 V, Gain = 0 dB
2
2.6
30
50
mV
mV
dB
| VOO
PSRR
| IIH
| IIL
|
Output offset voltage (measured differentially)
Power supply rejection ratio
–80
High-level input current (SE/BTL, FADE, HP/LINE,
SHUTDOWN, SEDIFF, SEMAX, VOLUME)
VDD = PVDD = 5.5 V,
VI = VDD = PVDD
|
1
1
μA
μA
Low-level input current (SE/BTL, FADE, HP/LINE,
SHUTDOWN, SEDIFF, SEMAX, VOLUME)
|
VDD = PVDD = 5.5 V, VI = 0 V
VDD = PVDD = 5 V, SE/BTL = 0 V,
SHUTDOWN = 2 V
6.7
4.5
9.0
6
IDD
Supply current, no load
mA
VDD = PVDD = 5 V, SE/BTL= 5 V,
SHUTDOWN = 2 V
VDD = 5 V = PVDD, SE/BTL = 0 V,
SHUTDOWN = 2 V, RL = 3Ω,
PO = 2 W, stereo
IDD
IDD(SD)
Supply current, max power into a 3-Ω load
1.5
10
ARMS
Supply current, shutdown mode
SHUTDOWN = 0.0 V
25
μA
OPERATING CHARACTERISTICS
TA = 25°C, VDD = PVDD = 5 V, RL = 3 Ω, Gain = 6 dB, Stereo (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
mW
THD = 1%, f = 1 kHz, RL = 16 Ω (SE)
195
235
THD = 10%, f = 1 kHz, RL = 16 Ω (SE)
mW
PO
Output power
THD = 1%, f = 1 kHz, RL = 3 Ω (BTL)
2.0
W
THD = 10%, f = 1 kHz, VDD = 5.5 V, RL =3 Ω (BTL)
PO = 0.9 W, RL = 8 Ω (BTL), f = 20 Hz to 20 kHz
PO = 0.1 W, RL = 16 Ω (SE), f = 20 Hz to 20 kHz
RL = 8 Ω, Measured between output and VDD = 5.5 V
3.2
THD+N
Total harmonic distortion + noise
<0.1%
0.03%
VOH
VOL
High-level output voltage
Low-level output voltage
700
400
mV
mV
RL = 8 Ω, Measured between output and GND,
VDD = 5.5 V
V(Bypass) Bypass voltage (Nominally VDD/2) Measured at pin 17, No load, VDD = 5.5 V
2.65
2.75
–66
–60
110
102
2.85
V
BTL (4Ω)
SE (32Ω)
BTL
dB
dB
dB
dB
Supply ripple rejection ratio
Crosstalk
f = 1 kHz, Gain = 0 dB, C(BYP) = 1 µF
SE
f = 20 Hz to 20 kHz, Gain = 0 dB,
C(BYP) = 1 µF
Noise output voltage
BTL
36
12
µVRMS
ZI
Input impedance (see Figure 17)
VOLUME = 5 V
kΩ
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
PWP Package
(Top View)
1
2
24
23
ROUT+
SE/BTL
PGND
ROUT−
PVDD
3
4
5
6
22
21
20
19
HP/LINE
VOLUME
SEDIFF
SEMAX
RHPIN
RLINEIN
RIN
VDD
7
18
17
16
15
14
13
AGND
8
LIN
BYPASS
FADE
9
LLINEIN
LHPIN
PVDD
10
11
12
SHUTDOWN
LOUT+
LOUT−
PGND
P0110-01
PIN Functions
PIN
I/O
DESCRIPTION
NAME
PGND
NO.
1, 13
12
3, 11
10
9
–
O
–
I
Power ground
LOUT–
PVDD
Left channel negative audio output
Supply voltage terminal for power stage
LHPIN
LLINEIN
LIN
Left channel headphone input, selected when HP/LINE is held high
Left channel line input, selected when HP/LINE is held low
Common left channel input for fully differential input. AC ground for single-ended inputs.
Supply voltage terminal
I
8
I
VDD
7
–
I
RIN
6
Common right channel input for fully differential input. AC ground for single-ended inputs.
Right channel line input, selected when HP/LINE is held low
Right channel headphone input, selected when HP/LINE is held high
Right channel negative audio output
RLINEIN
RHPIN
ROUT–
ROUT+
SHUTDOWN
5
I
4
I
2
O
O
I
24
15
Right channel positive audio output
Places the amplifier in shutdown mode if a TTL logic low is placed on this terminal
Places the amplifier in fade mode if a logic low is placed on this terminal; normal operation if a logic
high is placed on this terminal
FADE
16
I
BYPASS
AGND
17
18
19
20
21
I
–
I
Tap to voltage divider for internal mid-supply bias generator used for analog reference
Analog power supply ground
SEMAX
SEDIFF
VOLUME
Sets the maximum volume for single ended operation. DC voltage range is 0 to VDD
Sets the difference between BTL volume and SE volume. DC voltage range is 0 to VDD
Terminal for dc volume control. DC voltage range is 0 to VDD
.
I
.
I
.
Input MUX control. When logic high, RHPIN and LHPIN inputs are selected. When logic low, RLINEIN
and LLINEIN inputs are selected.
HP/LINE
22
I
Output MUX control. When this terminal is high, SE outputs are selected. When this terminal is low,
BTL outputs are selected.
SE/BTL
LOUT+
23
14
I
O
Left channel positive audio output.
4
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
FUNCTIONAL BLOCK DIAGRAM
R
RHPIN
MUX
RLINEIN
_
+
_
+
HP/LINE
ROUT+
RIN
BYP
BYP
+
_
_
ROUT-
+
EN
BYP
SE/BTL
SE/BTL
MUX
Control
PV
DD
HP/LINE
PGND
V
DD
Power
VOLUME
SEDIFF
SEMAX
FADE
BYPASS
Management
32-Step
Volume
Control
SHUTDOWN
AGND
L
LHPIN
MUX
LLINEIN
_
+
_
+
HP/LINE
LOUT+
LOUT-
LIN
BYP
BYP
+
_
_
+
EN
BYP
SE/BTL
NOTE: All resistor wipers are adjusted with 32-step volume control.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
Table 1. DC Volume Control (BTL Mode, VDD = 5 V)(1)
VOLUME (PIN 21)
GAIN OF AMPLIFIER
(2)
(Typ)
FROM (V)
0.00
0.33
0.44
0.56
0.67
0.78
0.89
1.01
1.12
1.23
1.35
1.46
1.57
1.68
1.79
1.91
2.02
2.13
2.25
2.36
2.47
2.58
2.70
2.81
2.92
3.04
3.15
3.26
3.38
3.49
3.60
3.71
TO (V)
0.26
0.37
0.48
0.59
0.70
0.82
0.93
1.04
1.16
1.27
1.38
1.49
1.60
1.72
1.83
1.94
2.06
2.17
2.28
2.39
2.50
2.61
2.73
2.83
2.95
3.06
3.17
3.29
3.40
3.51
3.63
5.00
–85
–40
–34
–31
–28
–25
–22
–19
–16
–13
–10
–7
–4
–2
–0
2
4
6
8
10
11
12
13
14
14.5
15
15.5
16
16.5
17
17.5
18
(1) For other values of VDD, scale the voltage values in the table by a factor of VDD/5.
(2) Tested in production. Remaining gain steps are specified by design.
6
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
Table 2. DC Volume Control (SE Mode, VDD = 5 V)(1)
SE_VOLUME = VOLUME - SEDIFF or SEMAX
GAIN OF AMPLIFIER
(Typ)
FROM (V)
0.00
0.33
0.44
0.56
0.67
0.78
0.89
1.01
1.12
1.23
1.35
1.46
1.57
1.68
1.79
1.91
2.02
2.13
2.25
2.36
2.47
2.58
2.70
2.81
2.92
3.04
3.15
3.26
3.38
3.49
3.60
3.71
TO (V)
0.26
0.37
0.48
0.59
0.70
0.82
0.93
1.04
1.16
1.27
1.38
1.49
1.60
1.72
1.83
1.94
2.06
2.17
2.28
2.39
2.50
2.61
2.73
2.83
2.95
3.06
3.17
3.29
3.40
3.51
3.63
5.00
–85(2)
–46
–40
–37
–34
–31
–28
–25
–22
–19
–16
–13
–10
–8
–6(2)
–4
–2
0(2)
2
4
5
(2)
6
7
8
8.5
9
9.5
10
10.5
11
11.5
12
(1) For other values of VDD, scale the voltage values in the table by a factor of VDD/5.
(2) Tested in production. Remaining gain steps are specified by design.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS
Test conditions (unless otherwise noted) for typical operating performance:
VDD = 5.0 V, CIN = 1 µF, CBYPASS = 1 µF, TA = 27°C, SHUTDOWN = VDD
Table of Graphs
Gain (BTL)
vs Volume voltage
Figure 1
vs Frequency
Figure 2, Figure 3, Figure 4
Figure 7, Figure 8, Figure 9
Figure 5, Figure 6
Figure 10
THD+N
THD+N
Total harmonic distortion plus noise (BTL)
vs Output power
vs Frequency
Total harmonic distortion plus noise (SE)
vs Output power
vs Output voltage
vs Total output power
vs Total output power
vs Frequency
Figure 11
PD
PD
Total power dissipation (BTL)
Total power dissipation (SE)
Crosstalk (BTL)
Figure 12
Figure 13
Figure 14
Crosstalk (SE)
vs Frequency
Figure 15
Inter-channel crosstalk
Input impedance
vs Frequency
Figure 16
vs Gain
Figure 17
PSRR
PSRR
IDD
Power supply rejection ratio (BTL)
Power supply rejection ratio (SE)
Supply current (BTL)
vs Frequency
Figure 18
vs Frequency
Figure 19
vs Total output power
vs Total output power
Figure 20
IDD
Supply current (SE)
Figure 21
TOTAL HARMONIC DISTORTION + NOISE (BTL)
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
vs
FREQUENCY
FREQUENCY
10
10
VDD = 5.0 V
RL = 3 Ω
PO = 500 mW
PO = 1 W
VDD = 5.0 V
RL = 4 Ω
PO = 250 mW
PO = 1 W
LINEIN Input − BTL Output
PO = 1.5 W
LINEIN Input − BTL Output
PO = 1.5 W
Gain = 6 dB
Gain = 6 dB
1
0.1
1
0.1
0.01
0.01
0.001
0.001
20
100
1k
10k 20k
20
100
1k
10k 20k
f − Frequency − Hz
f − Frequency − Hz
Figure 2.
Figure 3.
8
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
TOTAL HARMONIC DISTORTION + NOISE (BTL)
TOTAL HARMONIC DISTORTION + NOISE (SE)
vs
vs
FREQUENCY
FREQUENCY
10
1
10
1
VDD = 5.0 V
RL = 8 Ω
LINEIN Input − BTL Output
Gain = 6 dB
PO = 250 mW
PO = 500 mW
PO = 900 mW
VDD = 5.0 V
RL = 32 Ω
HPIN Input − SE Output
Gain = 0 dB
PO = 10 mW
PO = 40 mW
PO = 80 mW
0.1
0.1
0.01
0.001
0.01
0.001
20
100
1k
10k 20k
20
100
1k
10k 20k
f − Frequency − Hz
f − Frequency − Hz
Figure 4.
Figure 5.
TOTAL HARMONIC DISTORTION + NOISE (SE)
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
vs
FREQUENCY
OUTPUT POWER
10
100
VDD = 5.0 V
RL = 10 kΩ
HPIN Input − SE Output
VO = 500 mVRMS
VO = 1.0 VRMS
VO = 1.75 VRMS
RL = 3 Ω
LINEIN Input − BTL Output
Gain = 6 dB
VDD = 4.5 V
VDD = 5.0 V
VDD = 5.5 V
Gain = 0 dB
1
0.1
10
1
0.01
0.001
0.1
0.01
20
100
1k
10k 20k
1m
10m
100m
1
4
f − Frequency − Hz
PO − Output Power − W
Figure 6.
Figure 7.
TOTAL HARMONIC DISTORTION + NOISE (BTL)
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
vs
OUTPUT POWER
OUTPUT POWER
100
100
RL = 4 Ω
VDD = 4.5 V
RL = 8 Ω
VDD = 4.5 V
LINEIN Input − BTL Output
Gain = 6 dB
VDD = 5.0 V
VDD = 5.5 V
LINEIN Input − BTL Output
Gain = 6 dB
VDD = 5.0 V
VDD = 5.5 V
10
1
10
1
0.1
0.1
0.01
0.01
1m
10m
100m
1
3
1m
10m
100m
1
2
PO − Output Power − W
PO − Output Power − W
Figure 8.
Figure 9.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
TOTAL HARMONIC DISTORTION + NOISE (SE)
TOTAL HARMONIC DISTORTION + NOISE (SE)
vs
vs
OUTPUT POWER
OUTPUT VOLTAGE
100
10
100
10
VDD = 5.0 V
HPIN Input − SE Output
Gain = 0 dB
RL = 16 Ω
RL = 32 Ω
VDD = 5.0 V
RL = 10 kΩ
HPIN Input − SE Output
Gain = 0 dB
1
1
0.1
0.1
0.01
0.001
0.01
100u
1m
10m
100m
300m
0.0
500.0m
1.0
1.5
2.0
PO − Output Power − W
VO − Output Voltage − V
RMS
Figure 10.
Figure 11.
TOTAL POWER DISSIPATION (BTL)
TOTAL POWER DISSIPATION (SE)
vs
vs
TOTAL OUTPUT POWER
TOTAL OUTPUT POWER
200m
175m
150m
125m
100m
75m
50m
25m
0
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
VDD = 5.0 V
HPIN Input
SE Output
Gain = 0 dB
VDD = 5.0 V
LINEIN Input
BTL Output
Gain = 6 dB
RL = 3 Ω
RL = 4 Ω
RL = 8 Ω
RL = 16 Ω
RL = 32 Ω
0
100m
200m
300m
400m
500m
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
PO − Total Output Power − W
PO − Total Output Power − W
Figure 12.
Figure 13.
CROSSTALK (BTL)
vs
CROSSTALK (SE)
vs
FREQUENCY
FREQUENCY
0
−20
0
RL = 4 Ω
PO = 1 W
LINEIN Input − BTL Output
Gain = 6 dB
RL = 32 Ω
PO = 50 mW
HPIN Input − SE Output
−20
−40
Gain = 0 dB
−40
−60
−60
−80
−80
−100
−120
−140
−100
−120
−140
20
100
1k
10k 20k
20
100
1k
10k 20k
f − Frequency − Hz
f − Frequency − Hz
Figure 14.
Figure 15.
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
INTER-CHANNEL CROSSTALK
INPUT IMPEDANCE
vs
vs
FREQUENCY
GAIN
0
−20
120k
100k
80k
60k
40k
20k
0
VDD = 5.0 V
RL = 4 Ω
VIN = 1 VRMS − BTL Output
Gain = 18 dB
Line Active
HP Active
Differential
Single−Ended
−40
−60
−80
−100
−120
VDD = 5.0 V
RL = No Load
20
100
1k
10k 20k
−40 −35 −30 −25 −20 −15 −10 −5
0
5
10 15 20
f − Frequency − Hz
Gain − dB
Figure 16.
Figure 17.
POWER SUPPLY REJECTION RATIO (BTL)
POWER SUPPLY REJECTION RATIO (SE)
vs
vs
FREQUENCY
FREQUENCY
0
−20
−40
−60
−80
0
−20
−40
−60
−80
VDD = 5.0 V
RL = 4 Ω
BTL Output
Supply Ripple = 0.2 Vpp Sine Wave
VDD = 5.0 V
RL = 32 Ω
SE Output
Supply Ripple = 0.2 Vpp Sine Wave
Gain = 6 dB
Gain = 18 dB
Gain = 0 dB
Gain = 12 dB
20
100
1k
10k 20k
20
100
1k
10k 20k
f − Frequency − Hz
f − Frequency − Hz
Figure 18.
Figure 19.
SUPPLY CURRENT (BTL)
vs
SUPPLY CURRENT (SE)
vs
TOTAL OUTPUT POWER
TOTAL OUTPUT POWER
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
125m
100m
75m
50m
25m
0
VDD = 5.0 V
VDD = 5.0 V
LINEIN Input
BTL Output
Gain = 6 dB
HPIN Input
SE Output
Gain = 0 dB
RL = 3 Ω
RL = 4 Ω
RL = 8 Ω
RL = 16 Ω
RL = 32 Ω
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
100m
200m
300m
400m
500m
PO − Total Output Power − W
PO − Total Output Power − W
Figure 20.
Figure 21.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
APPLICATION INFORMATION
SELECTION OF COMPONENTS
Figure 22 and Figure 23 are schematic diagrams of typical notebook computer application circuits.
Right
Speaker
V
DD
24
23
ROUT+
SE/BTL
C
C
1
PGND
ROUT-
100 kΩ
2
3
C
S
22
100 kΩ
HP/LINE
1 kΩ
Power Supply
Right HP
PV
DD
C
i
4
5
6
21
20
19
RHPIN
RLINEIN
RIN
VOLUME
SEDIFF
Audio Source
C
i
In From DAC
or
Potentiometer
(DC Voltage)
Right Line
Audio Source
C
i
SEMAX
V
DD
C
S
Headphones
7
8
18
17
V
AGND
DD
C
(BYP)
C
i
LIN
BYPASS
1 kΩ
C
i
C
C
Left Line
9
16
15
LLINEIN
LHPIN
FADE
Audio Source
C
i
10
Left HP
Audio Source
System
Control
SHUTDOWN
11
12
14
13
PV
Power Supply
DD
Left
Speaker
LOUT+
PGND
C
S
LOUT-
A. A 0.1-μF ceramic capacitor should be placed as close as possible to the IC. For filtering lower-frequency noise
signals, a larger electrolytic capacitor of 10 μF or greater should be placed near the audio power amplifier.
Figure 22. Typical TPA6013A4 Application Circuit Using Single-Ended Inputs and Input MUX
12
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
Right
Speaker
V
DD
24
23
ROUT+
SE/BTL
C
C
1
PGND
ROUT-
100 kΩ
2
3
C
S
22
100 kΩ
HP/LINE
1 kΩ
Power Supply
PV
DD
4
5
6
21
20
19
NC
RHPIN
RLINEIN
RIN
VOLUME
SEDIFF
C
In From DAC
or
Potentiometer
(DC Voltage)
i
Right Negative
Differential Input Signal
C
i
Right Positive
Differential Input Signal
SEMAX
V
DD
C
S
Headphones
7
8
18
17
V
AGND
DD
C
(BYP)
C
i
Left Positive Differential
Input Signal
LIN
BYPASS
1 kΩ
C
i
C
C
Left Negative
Differential Input Signal
9
16
15
LLINEIN
LHPIN
FADE
10
System
Control
NC
SHUTDOWN
11
12
14
13
PV
Power Supply
DD
Left
Speaker
LOUT+
PGND
C
S
LOUT-
A. A 0.1-μF ceramic capacitor should be placed as close as possible to the IC. For filtering lower-frequency noise
signals, a larger electrolytic capacitor of 10 μF or greater should be placed near the audio power amplifier.
Figure 23. Typical TPA6013A4 Application Circuit Using Differential Inputs
SE/BTL OPERATION
The ability of the TPA6013A4 to easily switch between BTL and SE modes is one of its most important cost
saving features. This feature eliminates the requirement for an additional headphone amplifier in applications
where internal stereo speakers are driven in BTL mode but external headphone or speakers must be
accommodated. Internal to the TPA6013A4, two separate amplifiers drive OUT+ and OUT–. The SE/BTL input
controls the operation of the follower amplifier that drives LOUT– and ROUT–. When SE/BTL is held low, the
amplifier is on and the TPA6013A4 is in the BTL mode. When SE/BTL is held high, the OUT– amplifiers are in a
high output impedance state, which configures the TPA6013A4 as an SE driver from LOUT+ and ROUT+. IDD is
reduced by approximately one-third in SE mode. Control of the SE/BTL input can be from a logic-level CMOS
source or, more typically, from a resistor divider network as shown in Figure 24. The trip level for the SE/BTL
input can be found in the recommended operating conditions table.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
RHPIN
4
5
R
MUX
RLINEIN
_
+
_
+
ROUT+ 24
Input
MUX
Control
22 HP/LINE
Bypass
6
RIN
Bypass
C
O
V
DD
330 µF
+
_
_
+
ROUT-
2
1 kΩ
100 kΩ
EN
Bypass
100 kΩ
SE/BTL 23
LOUT+
Figure 24. TPA6013A4 Resistor Divider Network Circuit
Using a 1/8-in. (3,5 mm) stereo headphone jack, the control switch is closed when no plug is inserted. When
closed the 100-kΩ/1-kΩ divider pulls the SE/BTL input low. When a plug is inserted, the 1-kΩ resistor is
disconnected and the SE/BTL input is pulled high. When the input goes high, the OUT– amplifier is shut down
causing the speaker to mute (open-circuits the speaker). The OUT+ amplifier then drives through the output
capacitor (Co) into the headphone jack.
HP/LINE OPERATION
The HP/LINE input controls the internal input multiplexer (MUX). Refer to the block diagram in Figure 24. This
allows the device to switch between two separate stereo inputs to the amplifier. For design flexibility, the
HP/LINE control is independent of the output mode, SE or BTL, which is controlled by the aforementioned
SE/BTL pin. To allow the amplifier to switch from the LINE inputs to the HP inputs when the output switches from
BTL mode to SE mode, simply connect the SE/BTL control input to the HP/LINE input.
When this input is logic high, the RHPIN and LHPIN inputs are selected. When this terminal is logic low, the
RLINEIN and LLINEIN inputs are selected. This operation is also detailed in Table 3 and the trip levels for a logic
low (VIL) or logic high (VIH) can be found in the recommended operating conditions table.
SHUTDOWN MODES
The TPA6013A4 employs a shutdown mode of operation designed to reduce supply current (IDD) to the absolute
minimum level during periods of nonuse for battery-power conservation. The SHUTDOWN input terminal should
be held high during normal operation when the amplifier is in use. Pulling SHUTDOWN low causes the outputs to
mute and the amplifier to enter a low-current state, IDD = 20 μA. SHUTDOWN should never be left unconnected
because amplifier operation would be unpredictable.
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
Table 3. HP/LINE, SE/BTL, and Shutdown Functions
(1)
INPUTS
SE/BTL
X
AMPLIFIER STATE
HP/LINE
X
SHUTDOWN
Low
INPUT
X
OUTPUT
Mute
BTL
SE
Low
Low
High
Line
Line
HP
Low
High
Low
High
High
High
High
BTL
SE
High
High
HP
(1) Inputs should never be left unconnected.
FADE OPERATION
For design flexibility, a fade mode is provided to slowly ramp up the amplifier gain when coming out of shutdown
mode and conversely ramp the gain down when going into shutdown. This mode provides a smooth transition
between the active and shutdown states and virtually eliminates any pops or clicks on the outputs.
When the FADE input is a logic low, the device is placed into fade-on mode. A logic high on this pin places the
amplifier in the fade-off mode. The voltage trip levels for a logic low (VIL) or logic high (VIH) can be found in the
recommended operating conditions table.
When a logic low is applied to the FADE pin and a logic low is then applied on the SHUTDOWNpin, the channel
gain steps down from gain step to gain step at a rate of two clock cycles per step. With a nominal internal clock
frequency of 58 Hz, this equates to 34 ms (1/24 Hz) per step. The gain steps down until the lowest gain step is
reached. The time it takes to reach this step depends on the gain setting prior to placing the device in shutdown.
For example, if the amplifier is in the highest gain mode of 18 dB, the time it takes to ramp down the channel
gain is 1.05 seconds. This number is calculated by taking the number of steps to reach the lowest gain from the
highest gain, or 31 steps, and multiplying by the time per step, or 34 ms.
After the channel gain is stepped down to the lowest gain, the amplifier begins discharging the bypass capacitor
from the nominal voltage of VDD/2 to ground. This time is dependent on the value of the bypass capacitor. For a
0.47-μF capacitor that is used in the application diagram in Figure 22, the time is approximately 500 ms. This
time scales linearly with the value of bypass capacitor. For example, if a 1-μF capacitor is used for bypass, the
time period to discharge the capacitor to ground is twice that of the 0.47-μF capacitor, or 1 second. Figure 25 is a
waveform captured at the output during the shutdown sequence when the part is in fade-on mode. The gain is
set to the highest level and the output is at VDD when the amplifier is shut down.
When a logic high is placed on the SHUTDOWN pin and the FADE pin is still held low, the device begins the
start-up process. The bypass capacitor will begin charging. Once the bypass voltage reaches the final value of
VDD/2, the gain increases from the lowest gain level to the gain level set by the dc voltage applied to the
VOLUME, SEDIFF, and SEMAX pins.
In the fade-off mode, the amplifier stores the gain value prior to starting the shutdown sequence. The output of
the amplifier immediately drops to VDD/2 and the bypass capacitor begins a smooth discharge to ground. When
shutdown is released, the bypass capacitor charges up to VDD/2 and the channel gain returns immediately to the
value stored in memory. Figure 26 is a waveform captured at the output during the shutdown sequence when the
part is in the fade-off mode. The gain is set to the highest level, and the output is at VDD when the amplifier is
shut down.
The power-up sequence is different from the shutdown sequence and the voltage on the FADEpin does not
change the power-up sequence. Upon a power-up condition, the TPA6013A4 begins in the lowest gain setting
and steps up every 2 clock cycles until the final value is reached as determined by the dc voltage applied to the
VOLUME, SEDIFF, and SEMAX pins.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
Device Shutdown
Device Shutdown
ROUT+
ROUT+
Figure 25. Shutdown Sequence in the Fade-on
Mode
Figure 26. Shutdown Sequence in the Fade-off
Mode
VOLUME, SEDIFF, AND SEMAX OPERATION
Three pins labeled VOLUME, SEDIFF, and SEMAX control the BTL volume when driving speakers and the SE
volume when driving headphones. All of these pins are controlled with a dc voltage, which should not exceed
VDD
.
When driving speakers in BTL mode, the VOLUME pin is the only pin that controls the gain. Table 1 shows the
gain for the BTL mode. The voltages listed in the table are for VDD = 5 V. For a different VDD, the values in the
table scale linearly. If VDD = 4 V, multiply all the voltages in the table by 4 V/5 V, or 0.8.
The TPA6013A4 allows the user to specify a difference between BTL gain and SE gain. This is desirable to avoid
any listening discomfort when plugging in headphones. When switching to SE mode, the SEDIFF and SEMAX
pins control the singe-ended gain proportional to the gain set by the voltage on the VOLUME pin. When SEDIFF
= 0 V, the difference between the BTL gain and the SE gain is 6 dB. Refer to the section labeled bridge-tied load
versus single-ended load for an explanation on why the gain in BTL mode is 2x that of single-ended mode, or
6dB greater. As the voltage on the SEDIFF terminal is increased, the gain in SE mode decreases. The voltage
on the SEDIFF terminal is subtracted from the voltage on the VOLUME terminal and this value is used to
determine the SE gain.
Some audio systems require that the gain be limited in the single-ended mode to a level that is comfortable for
headphone listening. Most volume control devices only have one terminal for setting the gain. For example, if the
speaker gain is 18 dB, the gain in the headphone channel is fixed at 12 dB. This level of gain could cause
discomfort to listeners and the SEMAX pin allows the designer to limit this discomfort when plugging in
headphones. The SEMAX terminal controls the maximum gain for single-ended mode.
The functionality of the SEDIFF and SEMAX pin are combined to set the SE gain. A block diagram of the
combined functionality is shown in Figure 27. The value obtained from the block diagram for SE_VOLUME is a
dc voltage that can be used in conjunction with Table 2 to determine the SE gain. Again, the voltages listed in
the table are for VDD = 5 V. The values must be scaled for other values of VDD
.
Table 1 and Table 2 show a range of voltages for each gain step. There is a gap in the voltage between each
gain step. This gap represents the hysteresis about each trip point in the internal comparator. The hysteresis
ensures that the gain control is monotonic and does not oscillate from one gain step to another. If a
potentiometer is used to adjust the voltage on the control terminals, the gain increases as the potentiometer is
turned in one direction and decreases as it is turned back the other direction. The trip point, where the gain
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
actually changes, is different depending on whether the voltage is increased or decreased as a result of the
hysteresis about each trip point. The gaps in Table 1 and Table 2 can also be thought of as indeterminate states
where the gain could be in the next higher gain step or the lower gain step depending on the direction the
voltage is changing. If using a DAC to control the volume, set the voltage in the middle of each range to ensure
that the desired gain is achieved.
A pictorial representation of the volume control can be found in Figure 28. The graph focuses on three gain steps
with the trip points defined in Table 1 for BTL gain. The dotted line represents the hysteresis about each gain
step.
SEDIFF (V)
SEMAX (V)
-
Is SEMAX>
(VOLUME-SEDIFF)
?
+
VOLUME-SEDIFF
YES
VOLUME (V)
SE_VOLUME (V) = VOLUME (V) - SEDIFF (V)
NO
SE_VOLUME (V) = SEMAX (V)
Figure 27. Block Diagram of SE Volume Control
14
13
12
2.61
2.70 2.73
2.81
Voltage on VOLUME Pin - V
Figure 28. DC Volume Control Operation
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
INPUT RESISTANCE
Each gain setting is achieved by varying the input resistance of the amplifier, which can range from its smallest
value to over six times that value. As a result, if a single capacitor is used in the input high-pass filter, the –3 dB
or cutoff frequency also changes by over six times.
R
f
C
R
i
IN
Input Signal
Figure 29. Resistor on Input for Cut-Off Frequency
The input resistance at each gain setting is given in Figure 17.
The –3-dB frequency can be calculated using Equation 1.
1
ƒ
+
*3 dB
2p CR
i
(1)
INPUT CAPACITOR, Ci
In the typical application an input capacitor (Ci) is required to allow the amplifier to bias the input signal to the
proper dc level for optimum operation. In this case, Ci and the input impedance of the amplifier (Ri) form a
high-pass filter with the corner frequency determined in Equation 2.
−3 dB
1
f
+
c(highpass)
2pR C
i
i
f
c
(2)
The value of Ci is important to consider as it directly affects the bass (low frequency) performance of the circuit.
Consider the example where Ri is 70 kΩ and the specification calls for a flat-bass response down to 40 Hz.
Equation 2 is reconfigured as Equation 3.
1
C
+
i
2pR f
c
i
(3)
In this example, Ci is 56.8 nF, so one would likely choose a value in the range of 56 nF to 1 μF. A further
consideration for this capacitor is the leakage path from the input source through the input network (Ci) and the
feedback network to the load. This leakage current creates a dc offset voltage at the input to the amplifier that
reduces useful headroom, especially in high gain applications. For this reason, a low-leakage tantalum or
ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor
should face the amplifier input in most applications as the dc level there is held at VDD/2, which is likely higher
than the source dc level. Note that it is important to confirm the capacitor polarity in the application.
18
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
POWER SUPPLY DECOUPLING, C(S)
The TPA6013A4 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to
ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents
oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved by
using two capacitors of different types that target different types of noise on the power supply leads. For higher
frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic
capacitor, typically 0.1 μF placed as close as possible to the device VDD lead, works best. For filtering
lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 μF or greater placed near the audio
power amplifier is recommended.
MIDRAIL BYPASS CAPACITOR, C(BYP)
The midrail bypass capacitor (C(BYP)) is the most critical capacitor and serves several important functions. During
start-up or recovery from shutdown mode, C(BYP) determines the rate at which the amplifier starts up. The second
function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This
noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and
THD+N.
Bypass capacitor (C(BYP)) values of 0.47-μF to 1-μF ceramic or tantalum low-ESR capacitors are recommended
for the best THD and noise performance. For the best pop performance, choose a value for C(BYP) that is equal to
or greater than the value chosen for Ci. This ensures that the input capacitors are charged up to the midrail
voltage before C(BYP) is fully charged to the midrail voltage.
OUTPUT COUPLING CAPACITOR, C(C)
In the typical single-supply SE configuration, an output coupling capacitor (C(C)) is required to block the dc bias at
the output of the amplifier, thus preventing dc currents in the load. As with the input coupling capacitor, the
output coupling capacitor and impedance of the load form a high-pass filter governed by Equation 4.
−3 dB
1
f
+
c(high)
2pR C
(C)
L
f
c
(4)
The main disadvantage, from a performance standpoint, is the load impedances are typically small, which drives
the low-frequency corner higher, degrading the bass response. Large values of C(C) are required to pass low
frequencies into the load. Consider the example where a C(C) of 330 μF is chosen and loads vary from 3Ω ,4 Ω,
8Ω, 32Ω , 10 kΩ, and 47 kΩ. Table 4 summarizes the frequency response characteristics of each configuration.
Table 4. Common Load Impedances vs Low Frequency
Output Characteristics in SE Mode
RL
3 Ω
C(C)
LOWEST FREQUENCY
161 Hz
330 μF
330 μF
330 μF
330 µF
330 μF
330 μF
4 Ω
120 Hz
8 Ω
60 Hz
32 Ω
15 Hz
10,000 Ω
47,000 Ω
0.05 Hz
0.01 Hz
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
As Table 4 indicates, most of the bass response is attenuated into a 4-Ω load, an 8-Ω load is adequate,
headphone response is good, and drive into line level inputs (a home stereo for example) is exceptional.
USING LOW-ESR CAPACITORS
Low-ESR capacitors are recommended throughout this applications section. A real (as opposed to ideal)
capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this
resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this
resistance, the more the real capacitor behaves like an ideal capacitor.
BRIDGE-TIED LOAD vs SINGLE-ENDED LOAD
Figure 30 shows a Class-AB audio power amplifier (APA) in a BTL configuration. The TPA6013A4 BTL amplifier
consists of two Class-AB amplifiers driving both ends of the load. There are several potential benefits to this
differential drive configuration, but, initially consider power to the load. The differential drive to the speaker
means that as one side is slewing up, the other side is slewing down, and vice versa. This in effect doubles the
voltage swing on the load as compared to a ground referenced load. Plugging 2 × VO(PP) into the power equation,
where voltage is squared, yields 4× the output power from the same supply rail and load impedance (see
Equation 5).
V
O(PP)
V
+
(rms)
Ǹ
2 2
2
V
(rms)
Power +
R
L
(5)
V
DD
V
O(PP)
2x V
O(PP)
R
L
V
DD
-V
O(PP)
Figure 30. Bridge-Tied Load Configuration
20
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
In a typical computer sound channel operating at 5 V, bridging raises the power into an 8-Ω speaker from a
singled-ended (SE, ground reference) limit of 250 mW to 1 W. In sound power that is a 6-dB improvement, which
is loudness that can be heard. In addition to increased power there are frequency response concerns. Consider
the single-supply SE configuration shown in Figure 31. A coupling capacitor is required to block the dc offset
voltage from reaching the load. These capacitors can be quite large (approximately 33μF to 1000μF), so they
tend to be expensive, heavy, occupy valuable PCB area, and have the additional drawback of limiting
low-frequency performance of the system. This frequency limiting effect is due to the high-pass filter network
created with the speaker impedance and the coupling capacitance and is calculated with Equation 6.
1
f
+
(c)
2pR C
L
C
(6)
For example, a 68-μF capacitor with an 8-Ω speaker would attenuate low frequencies below 293 Hz. The BTL
configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency
performance is then limited only by the input network and speaker response. Cost and PCB space are also
minimized by eliminating the bulky coupling capacitor.
V
DD
-3 dB
V
O(PP)
C
(C)
V
O(PP)
R
L
f
c
Figure 31. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4× the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the crest factor and thermal
considerations section.
SINGLE-ENDED OPERATION
In SE mode (see Figure 31), the load is driven from the primary amplifier output for each channel (OUT+).
The amplifier switches single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state, and effectively reduces the amplifier's gain by 6 dB.
BTL AMPLIFIER EFFICIENCY
Class-AB amplifiers are inefficient. The primary cause of these inefficiencies is voltage drop across the output
stage transistors. There are two components of the internal voltage drop. One is the headroom or dc voltage
drop that varies inversely to output power. The second component is due to the sine-wave nature of the output.
The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD. The
internal voltage drop multiplied by the RMS value of the supply current (IDDrms) determines the internal power
dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the
load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 32).
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
I
V
O
DD
I
DD(avg)
V
(LRMS)
Figure 32. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
P
L
Efficiency of a BTL amplifier +
P
SUP
Where:
2
2
V rms
V
V
P
L
P
P
+
, and V
+
, therefore, P
+
L
L
LRMS
Ǹ
R
2R
2
L
L
p
p
V
R
V
R
1
p
P
L
1
p
P
L
2V
+
sin(t) dt
[cos(t)]
0 +
ŕ
P
P
+ V
I
avg
I
avg +
and
and
SUP
DD DD
DD
p R
0
L
Therefore,
2 V
V
DD
p R
P
P
+
SUP
L
(7)
substituting PL and PSUP into Equation 7,
2
V
P
2 R
p V
L
P
Efficiency of a BTL amplifier +
+
2 V
V
P
4 V
DD
DD
p R
L
Where:
V
Ǹ2 P R
L
+
P
L
Therefore,
Ǹ2 P R
p
L
L
h
+
BTL
4 V
DD
PL = Power delivered to load
VP = Peak voltage on BTL load
PSUP = Power drawn from power supply
VLRMS = RMS voltage on BTL load
RL = Load resistance
IDDavg = Average current drawn from the power supply
VDD = Power supply voltage
ηBTL = Efficiency of a BTL amplifier
(8)
Table 5 employs Equation 8 to calculate efficiencies for four different output power levels. Note that the efficiency
of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in
a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full
output power is less than in the half power range. Calculating the efficiency for a specific system is the key to
proper power supply design. For a stereo 1-W audio system with 8-Ω loads and a 5-V supply, the maximum draw
on the power supply is almost 3.25 W.
22
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
TPA6013A4
www.ti.com
SLOS635 –NOVEMBER 2009
Table 5. Efficiency vs Output Power in 5-V, 8-Ω BTL Systems
OUTPUT POWER
(W)
EFFICIENCY
(%)
PEAK VOLTAGE
(V)
INTERNAL DISSIPATION
(W)
0.55
0.62
0.59
0.53
0.25
0.50
1.00
1.25
31.4
44.4
62.8
70.2
2.00
2.83
4.00
4.47(1)
(1) High peak voltages cause the THD to increase.
A final point to remember about Class-AB amplifiers (either SE or BTL) is how to manipulate the terms in the
efficiency equation to utmost advantage when possible. Note that in equation 8, VDD is in the denominator. This
indicates that as VDD goes down, efficiency goes up.
CREST FACTOR AND THERMAL CONSIDERATIONS
Class-AB power amplifiers dissipate a significant amount of heat in the package under normal operating
conditions. A typical music CD requires 12 dB to 15 dB of dynamic range, or headroom above the average power
output, to pass the loudest portions of the signal without distortion. In other words, music typically has a crest
factor between 12 dB and 15 dB. When determining the optimal ambient operating temperature, the internal
dissipated power at the average output power level must be used. From the TPA6013A4 data sheet, one can
see that when the TPA6013A4 is operating from a 5-V supply into a 3-Ω speaker, that 4-W peaks are available.
Use equation 9 to convert watts to dB.
P
4 W
1 W
W
P
+ 10Log
+ 10Log
+ 6 dB
dB
P
ref
(9)
Subtracting the headroom restriction to obtain the average listening level without distortion yields:
•
•
•
•
•
6 dB – 15 dB = –9 dB (15-dB crest factor)
6 dB – 12 dB = –6 dB (12-dB crest factor)
6 dB – 9 dB = –3 dB (9-dB crest factor)
6 dB – 6 dB = 0 dB (6-dB crest factor)
6 dB – 3 dB = 3 dB (3-dB crest factor)
To convert dB back into watts use equation 10.
PdBń10
P
+ 10
P
ref
W
= 63 mW (18-db crest factor)
= 125 mW (15-db crest factor)
= 250 mW (12-db crest factor)
= 500 mW (9-db crest factor)
= 1000 mW (6-db crest factor)
= 2000 mW (3-db crest factor)
(10)
This is valuable information to consider when attempting to estimate the heat dissipation requirements for the
amplifier system. Comparing the worst case, which is 2 W of continuous power output with a 3-dB crest factor,
against 12-dB and 15-dB applications significantly affects maximum ambient temperature ratings for the system.
Using the power dissipation curves for a 5-V, 3-Ω system, the internal dissipation in the TPA6013A4 and
maximum ambient temperatures is shown in Table 6.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s) :TPA6013A4
TPA6013A4
SLOS635 –NOVEMBER 2009
www.ti.com
Table 6. TPA6013A4 Power Rating, 5-V, 3-Ω Stereo
PEAK OUTPUT POWER
(W)
POWER DISSIPATION
AVERAGE OUTPUT POWER
MAXIMUM AMBIENT
TEMPERATURE
(W/Channel)
4
4
4
4
4
4
2 W (3 dB)
1 W (6 dB)
1.7
1.6
1.4
1.1
0.8
0.6
–3°C
6°C
500 mW (9 dB)
250 mW (12 dB)
125 mW (15 dB)
63 mW (18 dB)
24°C
51°C
78°C
96°C
Table 7. TPA6013A4 Power Rating, 5-V, 8-Ω Stereo
PEAK OUTPUT POWER
(W)
POWER DISSIPATION
AVERAGE OUTPUT POWER
MAXIMUM AMBIENT
TEMPERATURE
(W/Channel)
2.5
2.5
2.5
2.5
1250 mW (3-dB crest factor)
1000 mW (4-dB crest factor)
500 mW (7-dB crest factor)
250 mW (10-dB crest factor)
0.55
0.62
0.59
0.53
100°C
94°C
97°C
102°C
The maximum dissipated power (PD(max)) is reached at a much lower output power level for an 8-Ω load than for
a 3-Ω load. As a result, this simple formula for calculating PD(max) may be used for an 8-Ω application.
2
DD
2V
P
+
D(max)
2
p R
L
(11)
However, in the case of a 3-Ω load, the PD(max) occurs at a point well above the normal operating power level.
The amplifier may therefore be operated at a higher ambient temperature than required by the PD(max) formula for
a 3-Ω load.
The maximum ambient temperature depends on the heat-sinking ability of the PCB system. The derating factor
for the PWP package is shown in the dissipation rating table. Use equation 12 to convert this to θJA.
.
1
1
Θ
+
+
+ 45°CńW
JA
0.022
Derating Factor
(12)
To calculate maximum ambient temperatures, first consider that the numbers from the dissipation graphs are per
channel, so the dissipated power needs to be doubled for two channel operation. Given θJA, the maximum
allowable junction temperature, and the total internal dissipation, the maximum ambient temperature can be
calculated using Equation 13. The maximum recommended junction temperature for the TPA6013A4 is 150°C.
The internal dissipation figures are taken from the Power Dissipation vs Output Power graphs.
T
Max + T Max * Θ
P
A
J
JA
D
(
)
(
)
+ 150 * 45 0.6 2 + 96°C 15-dB crest factor
(13)
NOTE
Internal dissipation of 0.6 W is estimated for a 2-W system with 15-dB crest factor per
channel.
Table 6 and Table 7 show that some applications require no airflow to keep junction temperatures in the
specified range. The TPA6013A4 is designed with thermal protection that turns the device off when the junction
temperature surpasses 150°C to prevent damage to the IC. Table 6 and Table 7 were calculated for maximum
listening volume without distortion. When the output level is reduced the numbers in the table change
significantly. Also, using 8-Ω speakers increases the thermal performance by increasing amplifier efficiency.
24
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA6013A4
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
TPA6013A4PWPR
3-W Stereo Audio Power Amplifier with Advanced DC Volume Control 24-HTSSOP -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明