TPL9202_1 [TI]
8-CHANNEL RELAY DRIVER WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION; 具有集成的5V LDO和欠压检测8路继电器驱动器
| 型号： | TPL9202_1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 8-CHANNEL RELAY DRIVER WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION |
| 文件： | 总20页 (文件大小：696K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
1
FEATURES
APPLICATIONS
•
Electrical Applicances
2
•
Eight Low-Side Drivers With Internal Clamp for
Inductive Loads and Current Limiting for Self
Protection
–
–
–
–
–
–
Air Conditioning Units
Ranges
Dishwashers
Refrigerators
Microwaves
Washing Machines
–
Seven Outputs Rated at 150 mA and
Controlled Through Serial Interface
–
One Output Rated at 150 mA and
Controlled Through Serial Interface and
Dedicated Enable Pin
•
General-Purpose Interface Circuit Allowing
Microcontroller Interface to Relays, Electric
Motors, LEDs, and Buzzers
•
•
•
5-V ± 5% Regulated Power Supply With
200-mA Load Capability at VIN Max of 18 V
Internal Voltage Supervisory for Regulated
Output
PWP PACKAGE
(TOP VIEW)
Serial Communications for Control of Eight
Low-Side Drivers
1
2
3
4
5
6
7
8
9
10
BO_OUTZ
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
GND
20
19
18
17
16
15
14
13
12
11
BO
VIN
•
•
Enable/Disable Input for OUT1
5VOUT
SCLK
NCS
5-V or 3.3-V I/O Tolerant for Interface to
Microcontroller
MOSI
•
•
Programmable Power-On Reset Delay Before
RST Asserted High, Once 5 V Is Within
Specified Range (6 ms Typ)
RST
RDELAY
EN1
NC
Programmable Deglitch Timer Before RST
Asserted Low (40 µs Typ)
•
•
Programmable Brown-Out Feature
Thermal Shutoff for Self Protection
NC – No internal connection
DESCRIPTION/ORDERING INFORMATION
The power supply provides regulated 5-V output to power the system microcontroller and drive eight low-side
switches. The brown-out detection output (BO_OUTZ) warns the system if there is a temporary drop in the
supply voltage, so the system can prevent potentially hazardous situations.
A serial communications interface controls the eight low-side outputs; each output has an internal snubber circuit
to absorb the inductive load at turn OFF. Alternatively, the system can use a fly-back diode to VIN to help
recirculate the energy in an inductive load at turn OFF.
ORDERING INFORMATION(1)
TA
PACKAGE(2)
Reel of 2000
Tube of 70
ORDERABLE PART NUMBER
TPL9202PWPR
TOP-SIDE MARKING
–40°C to 125°C
PowerPAD™ – PWP
PL202
TPL9202PWP
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2008, Texas Instruments Incorporated
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
PINOUT CONFIGURATION
NO.
1
NAME
BO_OUTZ
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
GND
I/O
O
O
O
O
O
O
O
O
O
I
DESCRIPTION
Brown-out indicator
Low-side output 1
Low-side output 2
Low-side output 3
Low-side output 4
Low-side output 5
Low-side output 6
Low-side output 7
Low-side output 8
Ground
2
3
4
5
6
7
8
9
10
11
12
13
14(1)
15
16
17
18
19
20
NC
No connection
EN1
I
O
I/O
I
Enable/disable for OUT1
Power-up reset delay
RDELAY
RST
Power-on reset output (open drain)
Serial data input
MOSI
NCS
I
Chip select
SCLK
5VOUT
VIN
I
Serial clock for data synchronization
Regulated output
O
I
Unregulated input voltage source
Brown-out input threshold setting
BO
I
(1) Terminal 14 can be used as an input or an output.
2
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
FUNCTIONAL BLOCK DIAGRAM
OUT1
EN1
Enables
OUT1
OUT1
EN1
50 kΩ
OUT1 at
150 mA
6 V
Gate Control
for Outputs
1 Through 8
OUT2
OUT2
OUT2 at 150 mA
100 kΩ
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
OUT3 at 150 mA
OUT4 at 150 mA
OUT5 at 150 mA
OUT6 at 150 mA
OUT7 at 150 mA
OUT8 at 150 mA
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
NCS
NCS
Parallel
Register
SCLK
Serial
Register
SCLK
100 kΩ
MOSI
MOSI
20 Ω
(2 W)
100 kΩ
VIN
10 V
7–18 V
PMOS
5VOUT
Gate Drive
and Control
Optional, dependent
on heat-management
implementation
5 V
Bandgap
Ref
Comp
(see Note A)
–
+
GND
5 kΩ
GND
Vref
Voltage
Supervisor
RST
Vref
RST
Iconst
RDELAY
RDELAY
BO
VIN
Comp
BO_OUTZ
BO_OUTZ
1.2 V
Recommended
A. The resistor and Zener diode are required if there is insufficient thermal-management allocation.
Copyright © 2006–2008, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
DETAILED DESCRIPTION
The 5-V regulator is powered from VIN, and the regulated output is within 5 V ± 5% over the operating conditions.
The open-drain power-on reset (RST) pin remains low until the regulator exceeds the set threshold, and the timer
value set by the capacitor on the reset delay (RDELAY) pin expires. If both of these conditions are satisfied, RST is
asserted high. This signifies to the microcontroller that serial communications can be initiated to the TPL9202.
The serial communications is an 8-bit format, with data transfer synchronized using a serial clock from the
microcontroller. A single register controls all the outputs (one bit per output). The default value is zero (OFF). If
an output requires pulse width modulation (PWM) function, the register must be updated at a rate faster than the
desired PWM frequency. OUT1 can be controlled by serial input from the microcontroller or with the dedicated
enable (EN1) pin. If EN1 is pulled low or left open, the serial input through the shift register controls OUT1. If
EN1 is pulled high, OUT1 always is turned on, and the serial input for OUT1 is ignored.
The brown-out (BO) input is a resistor divided from the input supply and is used to determine if the supply
voltage drops to undesired levels. If the input drops below the programmed value, BO_OUTZ is pulled low, and
all outputs are disabled. Once the input supply line returns to the minimum desired level, the outputs are enabled
to the previous programmed states.
If RST is asserted, all outputs are turned OFF internally, and the input register is reset to all zeroes. The
microcontroller must write to the register to turn the outputs ON again.
4
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
Absolute Maximum Ratings(1)
MIN
MAX
24
UNIT
VIN
VI(unreg)
Unregulated input voltage(2) (3)
Logic input voltage(2) (3)
V
BO
24
7
EN1, MOSI, SCLK, and NCS
RST and RDELAY
OUT1–OUT8
VI(logic)
V
7
VO
Low-side output voltage
Output current limit(4)
16.5
V
OUTn = ON and shorted to VIN
with low impedance
ILIMIT
350
mA
θJA
θJC
θJP
PD
Thermal impedance, junction to ambient(5)
Thermal impedance, junction to top of package(5)
Thermal impedance, junction to thermal pad(5)
Continuous power dissipation(6)
Electrostatic discharge(7)
33 °C/W
20 °C/W
1.4 °C/W
3.7
2
W
kV
°C
°C
°C
ESD
TA
Operating ambient temperature range
Storage temperature range
–40
–65
125
125
260
Tstg
Tlead
Lead temperature
Soldering, 10 s
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to GND.
(3) Absolute negative voltage on these pins must not go below –0.5 V.
(4) Not more than one output should be shorted at a time, and duration of the short circuit should not exceed 1 ms.
(5) The thermal data is based on using 1-oz copper trace with JEDEC 51-5 test board for PWP.
(6) The data is based on ambient temperature of 25°C maximum.
(7) The Human Body Model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin.
Dissipation Ratings
T
A ≤ 25°C
DERATING FACTOR
ABOVE TA = 25°C
TA = 125°C
POWER RATING
PACKAGE
POWER RATING
PWP
3787 mW
30.3 mW/°C
757 mW
Recommended Operating Conditions
MIN
7
MAX
18
UNIT
VIN
VI(unreg)
Unregulated input voltage
V
BO (as seen by external resistor network)
0
18
VI(logic)
TA
Logic input voltage
EN1, RST, and RDELAY , MOSI, SCLK, and NCS
0
5.25
125
V
Operating ambient temperature
–40
°C
Copyright © 2006–2008, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
Electrical Characteristics
TA = –40°C to 125°C, VIN = 7 V to 18 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP(1)
MAX UNIT
Supply Voltage and Current
(2)
VIN
Input voltage
7
18
3
V
Enable = low, OUT1–OUT8 = Off
Enable = high, OUT1–OUT8 = On
IIN
Input supply current
mA
5
Logic Inputs (MOSI, NCS, SCLK, and EN1)
VIL
Logic input low level
Logic input high level
IIL = 100 µA
IIL = 100 µA
0.8
V
V
VIH
2.4
Reset (RST)
VOL
Low-level logic output
High-level logic output
Disabling reset threshold
Enabling reset threshold
Threshold hysteresis
IOL = 1.6 mA
0.4
4.5
V
V
V
V
V
(3)
VOH
5-kΩ pullup to VCC
5-V regulator ramps up
5-V regulator ramps down
VCC – 0.8
VH
4.25
3.75
0.5
VL
3.3
VHYS
0.12
Reset Delay (RDELAY
)
IOUT
tDW
tUP
Output current
18
3
28
6
48
µA
ms
µs
Reset delay timer
C = 47 nF
C = 47 nF
Reset capacitor to low level
45
Output (OUT1–OUT8)
VOL
IOH
Output ON
IOUTn = 150 mA
0.4
5
0.7
2
V
Output leakage
VOH = Max of 16.5 V
µA
Regulator Output (5VOUT
5VOUT Output supply
I5Vout
)
I5VOUT = 5 mA to 200 mA, VIN = 7 V to 18 V,
C5VOUT = 1 µF
4.75
200
5.25
V
Limit output short circuit
current
5VOUT = 0 V
mA
Brown-Out (BO) Input
Threshold for brown-out
detection
Brown-Out Detection Output (BO_OUTZ)
BOVthes
VIN reduced until BO_OUTZ goes low
1.3
V
VOL
VOH
Logic level output
Logic level output
IOL = 100 µA
0.4
V
V
(3)
Pullup to VCC
VCC – 0.8
Thermal Shutdown
TSD
Thermal shutdown
Hysteresis
150
20
°C
°C
THYS
(1) All typical values are at TA = 25°C.
(2) There are external high-frequency noise-suppression capacitors and filter capacitors on VIN
.
(3) VCC is the pullup resistor voltage.
6
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
Output Control Register
MSB
LSB
IN8
IN7
IN6
IN5
IN4
IN3
IN2
IN1
0
0
0
0
0
0
0
0
INn = 0 = Output OFF
INn = 1 = Output ON
To operate the output in PWM mode, the output control register must be updated at a rate twice the desired
PWM frequency of the output. Maximum PWM frequency is 5 kHz. The register is updated every 100 µs.
ENABLE TRUTH TABLE
SERIAL INPUT
FOR OUT1
EN1
OUT1
Open
H
L
On
Off
On
Off
On
On
Open
L
L
H
L
H
H
H
L
Copyright © 2006–2008, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
Serial Communications Interface
The serial communications are an 8-bit format, with data transfer synchronized using a serial clock from the
microcontroller (see Figure 1). A single register controls all the outputs. The signal gives the instruction to control
the output of TPL9202.
The NCS signal enables the SCLK and MOSI data when it is low. After NCS is set to low for T1, synchronization
clock and data begin to transmit and, after the 8-bit data has been transmitted, NCS is set high again to disable
SCLK and MOSI and to transfer the serial data to the control register. SCLK must be held low when NCS is high.
T2
T3
T8
T1
T4
T5
T1
NCS
SCLK
1
2
3
4
5
6
7
8
MSB
IN8
LSB
IN1
MOSI
XXX
IN7
IN6
IN5
IN4
IN3
IN2
T6
T7
Figure 1. Serial Communications
8
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
Timing Requirements
TA = –40°C to 125°C, VIN = 7 V to 18 V (unless otherwise noted)
MIN
TYP
MAX
UNIT
MHz
ns
fSPI
T1
T2
T3
T4
T5
T6
T7
T8
SPI frequency
4
Delay time, NCS falling edge to SCLK rising edge
Delay time, NCS falling edge to SCLK falling edge
Pulse duration, SCLK high
10
80
ns
60
ns
Pulse duration, SCLK low
60
ns
Delay time, last SCLK falling edge to NCS rising edge
Setup time, MOSI valid before SCLK edge
Hold time, MOSI valid after SCLK edge
Time between two words for transmitting
80
ns
10
ns
10
ns
170
ns
Reset Delay (RDELAY
)
The RDELAY output provides a constant current source to charge an external capacitor to approximately 6.5 V.
The external capacitor is selected to provide a delay time, based on the current equation for a capacitor,
I = C(Δv/Δt) and a 28-µA typical output current.
Therefore, the user should select a 47-nF capacitor to provide a 6-ms delay at 3.55 V.
I = C(Δv/Δt)
28 µA = C × (3.55 V/6 ms)
C = 47 nF
Copyright © 2006–2008, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
APPLICATION INFORMATION
Buzzer Driver
MOSI
SCLK
NCS
Relay Driver
Relay Driver
Relay Driver
Relay Driver
Fan Driver
MCU/DSP
8 Outputs
Fan Driver
Fan Driver
BO_OUTZ
TPL9202
RST
5VOUT 5% at 200 mA
EN1
Brown Out
R
DELAY
DC Input 7 V to 18 V
GND
Figure 2. Typical Application
Display
(LED/LCD/VFD)
Keypad
LED LED
Water
Supply
Valve
Filters
AC
Water
Outlet
Softener
Supply
Volume
Sensor
M
Power
Switch
Water-Level
Sensor
Controller
Driver
Optical
Sensor
BO
BO_OUTZ
Brown-Out
Detect
Temperature
Sensor
(Optional)
VIN
5VOUT
RST
Regulator
+
~
~
POR/SYS
-
Cover
Switch
TPL9202
Figure 3. Washing-Machine Application
10
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
PCB Layout
To maximize the efficiency of this package for application on a single layer or multilayer PCB, certain guidelines
must be followed when laying out this part on the PCB.
The following information is to be used as a guideline only.
For further information, see the PowerPAD concept implementation document.
Application Using a Multilayer PCB
In a multilayer board application, the thermal vias are the primary method of heat transfer from the package
thermal pad to the internal ground plane (see Figure 4 and Figure 5).
The efficiency of this method depends on several factors: die area, number of thermal vias, thickness of copper,
etc. (see the PowerPAD™ Thermally Enhanced Package Technical Brief, literature number SLMA002).
Solder Pad (Land Pattern)
Package Thermal Pad
Thermal Vias
Package Outline
Figure 4. Package and PCB Land Configuration for a Multilayer PCB
Power Pad
Package Solder Pad
Component Traces
1.5038–1.5748-mm
Component Trace
(2-oz Cu)
2 Plane
1.0142–1.0502-mm
Ground Plane
(1-oz Cu)
Thermal Via
4 Plane
1.5748 mm
0.5246–0.5606-mm
Power Plane
(1-oz Cu)
Thermal Isolation
Power Plane Only
0.0–0.071-mm Board Base
and Bottom Pad
Package Solder Pad
(Bottom Trace)
Figure 5. Multilayer Board (Side View)
Application Using a Single-Layer PCB
In a single-layer board application, the thermal pad is attached to a heat spreader (copper areas) by a low
thermal-impedance attachment method (solder paste or thermal conductive epoxy). With either method, it is
advisable to use as many copper traces as possible to dissipate the heat.
Copyright © 2006–2008, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
CAUTION:
If the attachment method is not implemented correctly, the functionality of the
product cannot be ensured. Power-dissipation capability is adversely affected if
the device is incorrectly mounted on the circuit board.
Use as Much Copper Area
as Possible for Heat Spread
Package Thermal Pad
Package Outline
Figure 6. Layout Recommendations for a Single-Layer PCB
12
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPL9202
TPL9202
8-CHANNEL RELAY DRIVER
WITH INTEGRATED 5-V LDO AND BROWN-OUT DETECTION
www.ti.com
SLIS124D–JUNE 2006–REVISED FEBRUARY 2008
Recommended Board Layout
6,5 SMOC
5,85
SMOC = Solder Mask Over Copper
SMO = Solder Mask Opening
1
0,65
0,27 (´20)
3,7 SMO
Figure 7. Recommended Board Layout for PWP
Copyright © 2006–2008, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPL9202
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jan-2008
PACKAGING INFORMATION
Orderable Device
TPL9202PWP
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
HTSSOP
PWP
20
20
20
20
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TPL9202PWPG4
TPL9202PWPR
TPL9202PWPRG4
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
TPL9202PWPR
HTSSOP PWP
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type Package Drawing Pins
HTSSOP PWP 20
SPQ
Length (mm) Width (mm) Height (mm)
346.0 346.0 33.0
TPL9202PWPR
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明