TPS2043 [TI]
TRIPLE POWER-DISTRIBUTION SWITCHES; 三重配电开关型号: | TPS2043 |
厂家: | TEXAS INSTRUMENTS |
描述: | TRIPLE POWER-DISTRIBUTION SWITCHES |
文件: | 总25页 (文件大小:436K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TPS2043
D PACKAGE
(TOP VIEW)
135-mΩ -Maximum (5-V Input) High-Side
MOSFET Switch
500 mA Continuous Current per Channel
GND1
IN1
OC1
1
2
3
4
5
6
7
8
16
15
14
13
12
11
Short-Circuit and Thermal Protection With
Overcurrent Logic Output
OUT1
OUT2
OC2
EN1
EN2
GND2
IN2
Operating Range . . . 2.7 V to 5.5 V
Logic-Level Enable Input
OC3
OUT3
2.5-ms Typical Rise Time
EN3
NC
10 NC
Undervoltage Lockout
9
NC
20 µA Maximum Standby Supply Current
Bidirectional Switch
TPS2053
D PACKAGE
(TOP VIEW)
Available in 16-pin SOIC Package
Ambient Temperature Range, –40°C to 85°C
GND1
IN1
OC1
1
2
3
4
5
6
7
8
16
15
14
13
12
11
2-kV Human-Body-Model, 200-V
Machine-Model ESD Protection
OUT1
OUT2
OC2
EN1
EN2
GND2
IN2
UL Listed – File No. E169910
OC3
description
OUT3
EN3
NC
10 NC
NC
The TPS2043 and TPS2053 triple power
distribution switches are intended for applications
where heavy capacitive loads and short circuits
are likely to be encountered. The TPS2043 and
9
NC – No internal connection
the TPS2053 incorporate in single packages three 135-mΩ N-channel MOSFET high-side power switches for
power-distribution systems that require multiple power switches. Each switch is controlled by a logic enable that
is compatible with 5-V logic and 3-V logic. Gate drive is provided by an internal charge pump that controls the
power-switch rise times and fall times to minimize current surges during switching. The charge pump, requiring
no external components, allows operation from supplies as low as 2.7 V.
When the output load exceeds the current-limit threshold or a short is present, the TPS2043 and TPS2053 limit
the output current to a safe level by switching into a constant-current mode, pulling the overcurrent (OCx) logic
output low. When continuous heavy overloads and short circuits increase the power dissipation in the switch
causing the junction temperature to rise, a thermal protection circuit shuts off the switch to prevent damage.
Recovery from a thermal shutdown is automatic once the device has cooled sufficiently. Internal circuitry
ensures the switch remains off until valid input voltage is present.
The TPS2043 and TPS2053 are designed to limit at 0.9-A load. These power distribution switches are available
in a 16-pin small-outline integrated circuit (SOIC) package and operate over an ambient temperature range of
–40°C to 85°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
SOIC
RECOMMENDED MAXIMUM
CONTINUOUS LOAD CURRENT
(A)
TYPICAL SHORT-CIRCUIT
CURRENT LIMIT AT 25°C
(A)
T
A
ENABLE
†
(D)
–40°C to 85°C
–40°C to 85°C
Active low
Active high
0.5
0.5
0.9
0.9
TPS2043D
TPS2053D
†
The D package is available taped and reeled. Add an R suffix to device type (e.g., TPS2043DR)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TPS2043 functional block diagram
OC1
Thermal
GND1
Sense
EN1
Current
Limit
Driver
Charge
Pump
†
†
CS
OUT1
OUT2
UVLO
Power Switch
CS
IN1
Charge
Pump
Current
Limit
Driver
OC2
OC3
EN2
Thermal
Sense
Thermal
Sense
GND2
EN3
Current
Limit
Driver
Charge
Pump
†
CS
OUT3
UVLO
Power Switch
IN2
†
Current sense
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
Terminal Functions
TERMINAL
NO.
I/O
DESCRIPTION
NAME
TPS2043
TPS2053
EN1
EN2
EN3
EN1
EN2
EN3
GND1
GND2
IN1
3
–
I
I
I
I
I
I
Enable input, logic low turns on power switch, IN1-OUT1.
Enable input, logic low turns on power switch, IN1-OUT2.
Enable input, logic low turns on power switch, IN2-OUT3.
Enable input, logic high turns on power switch, IN1-OUT1.
Enable input, logic high turns on power switch, IN1-OUT2.
Enable input, logic high turns on power switch, IN2-OUT3.
Ground
4
–
7
–
–
3
–
4
–
1
7
1
5
5
Ground
2
2
I
I
Input voltage
IN2
6
6
Input voltage
NC
8, 9, 10
16
13
12
15
14
11
8, 9, 10
16
13
12
15
14
11
No connection
OC1
OC2
OC3
OUT1
OUT2
OUT3
O
O
O
O
O
O
Overcurrent, logic output active low, IN1-OUT1
Overcurrent, logic output active low, IN1-OUT2
Overcurrent, logic output active low, IN2-OUT3
Power-switch output, IN1-OUT1
Power-switch output, IN1-OUT2
Power-switch output, IN2-OUT3
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
detailed description
power switch
The power switch is an N-channel MOSFET with a maximum on-state resistance of 135 mΩ (V
= 5 V).
I(INx)
Configured as a high-side switch, the power switch prevents current flow from OUTx to INx and INx to OUTx
when disabled. The power switch supplies a minimum of 500 mA per switch.
charge pump
An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate
of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires
very little supply current.
driver
The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated
electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and
fall times of the output voltage. The rise and fall times are typically in the 2-ms to 4-ms range.
enable (ENx or ENx)
Thelogicenabledisablesthepowerswitchandthebiasforthechargepump, driver, andothercircuitrytoreduce
the supply current to less than 20 µA when a logic high is present on ENx (TPS2043) or a logic low is present
on ENx (TPS2053). A logic zero input on ENx or logic high on ENx restores bias to the drive and control circuits
and turns the power on. The enable input is compatible with both TTL and CMOS logic levels.
overcurrent (OCx)
The OCx open-drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed.
current sense
A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than
conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry
sends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power FET into
its saturation region, which switches the output into a constant current mode and holds the current constant
while varying the voltage on the load.
thermal sense
The TPS2043 and TPS2053 implement a dual-threshold thermal trip to allow fully independent operation of the
power distribution switches. In an overcurrent or short-circuit condition the junction temperature rises. When
thedietemperaturerisestoapproximately140°C, theinternalthermalsensecircuitrycheckstodeterminewhich
power switch is in an overcurrent condition and turns off that switch, thus isolating the fault without interrupting
operationoftheadjacentpowerswitch. Hysteresisisbuiltintothethermalsense, andafterthedevicehascooled
approximately 20 degrees, the switch turns back on. The switch continues to cycle off and on until the fault is
removed. The (OCx) open-drain output is asserted (active low) when overtemperature or overcurrent occurs.
undervoltage lockout
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control
signal turns off the power switch.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Input voltage range, V
Output voltage range, V
(see Note1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6 V
I(INx)
(see Note1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to V
+ 0.3 V
O(OUTx)
I(INx)
Input voltage range, V
Continuous output current, I
or V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6 V
I(ENx)
I(ENx)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
O(OUTx)
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating virtual junction temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 125°C
J
Storage temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 260°C
Electrostatic discharge (ESD) protection: Human body model MIL-STD-883C . . . . . . . . . . . . . . . . . . . . . . 2 kV
Machine model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 kV
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltages are with respect to GND.
DISSIPATION RATING TABLE
DERATING FACTOR
T
≤ 25°C
T
A
= 70°C
T = 85°C
A
A
PACKAGE
POWER RATING
ABOVE T = 25°C
POWER RATING POWER RATING
A
D
725 mW
5.8 mW/°C
464 mW 377 mW
recommended operating conditions
TPS2043
TPS2053
UNIT
MIN
2.7
0
MAX
5.5
MIN
2.7
0
MAX
Input voltage, V
Input voltage, V
5.5
5.5
V
V
I(INx)
or V
5.5
I(ENx)
I(ENx)
Continuous output current, I
O(OUTx)
0
500
125
0
500
125
mA
°C
Operating virtual junction temperature, T
–40
–40
J
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
electrical characteristics over recommended operating junction temperature range, V
= 5.5 V,
I(IN)
I = rated current, V
= 0 V, V
= Hi (unless otherwise noted)
O
I(ENx)
I(ENx)
power switch
TPS2043
†
TPS2053
TYP
PARAMETER
UNIT
TEST CONDITIONS
MIN
TYP
MAX
MIN
MAX
V
= 5 V,
T = 25°C,
J
I(INx)
= 0.5 A
80
95
80
90
95
I
O
Static drain-source on-state
resistance, 5-V operation
V
= 5 V,
= 0.5 A
T = 85°C,
J
I(INx)
I(INx)
I(INx)
I(INx)
I(INx)
I(INx)
90
100
85
120
135
105
135
150
120
135
105
135
150
I
O
V
= 5 V,
= 0.5 A
T = 125°C,
J
100
85
mΩ
I
O
r
DS(on)
V
= 3.3 V, T = 25°C,
J
= 0.5 A
I
O
Static drain-source on-state
resistance, 3.3-V operation
V
= 3.3 V, T = 85°C,
J
= 0.5 A
100
115
2.5
3
100
115
2.5
3
I
O
V
= 3.3 V, T = 125°C,
J
= 0.5 A
I
O
V
C
= 5.5 V, T = 25°C,
J
= 1 µF,
R = 10 Ω
L
L
t
t
Rise time, output
Fall time, output
ms
ms
r
V
C
= 2.7 V, T = 25°C,
J
= 1 µF,
I(INx)
R = 10 Ω
L
L
V
C
= 5.5 V, T = 25°C,
J
I(INx)
L
4.4
2.5
4.4
2.5
= 1 µF,
R = 10 Ω
L
f
V
C
= 2.7 V, T = 25°C,
J
I(INx)
= 1 µF,
R = 10 Ω
L
L
†
Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately.
enable input ENx or ENx
TPS2043
MIN TYP
TPS2053
MIN TYP
PARAMETER
TEST CONDITIONS
UNIT
MAX
MAX
V
V
High-level input voltage
Low-level input voltage
2.7 V ≤ V
4.5 V ≤ V
≤ 5.5 V
≤ 5.5 V
≤ 4.5 V
2
2
V
V
IH
I(INx)
I(INx)
I(INx)
0.8
0.4
0.5
0.8
0.4
IL
2.7 V≤ V
TPS2043
TPS2053
V
V
= 0 V or V
= V
–0.5
I(ENx)
I(ENx)
I(IN)
I
I
Input current
µA
= V
or V
= 0 V
–0.5
0.5
20
40
I(ENx)
I(INx)
I(ENx)
t
t
Turnon time
Turnoff time
C
C
= 100 µF, R =10 Ω
20
40
ms
on
L
L
L
= 100 µF, R =10 Ω
off
L
current limit
TPS2043
MIN TYP
TPS2053
MIN TYP
†
PARAMETER
UNIT
TEST CONDITIONS
MAX
MAX
V
= 5 V, OUT connected to GND,
I(INx)
Device enable into short circuit
I
Short-circuit output current
0.7
0.9
1.1
0.7
0.9
1.1
A
OS
†
Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
electrical characteristics over recommended operating junction temperature range, V
= 5.5 V,
I(IN)
I = rated current, V
= 0 V, V
= Hi (unless otherwise noted) (continued)
O
I(ENx)
I(ENx)
supply current
TPS2043
TYP MAX
TPS2053
MIN TYP MAX
PARAMETER
TEST CONDITIONS
T = 25°C
UNIT
MIN
0.03
2
J
Supply
TPS2043
TPS2053
TPS2043
TPS2053
V
V
= V
I(ENx)
I(INx)
–40°C ≤ T ≤ 125°C
20
No Load
on OUTx
J
current,
low-level
output
µA
µA
T = 25°C
0.03
2
J
= 0 V
= 0 V
I(ENx)
–40°C ≤ T ≤ 125°C
20
J
T = 25°C
J
160
200
200
Supply
V
V
I(ENx)
–40°C ≤ T ≤ 125°C
No Load
on OUTx
J
current,
high-level
output
T = 25°C
160
200
200
J
= V
= V
I(ENx)
I(INx)
–40°C ≤ T ≤ 125°C
J
OUTx
connected
to ground
V
V
V
V
–40°C ≤ T ≤ 125°C TPS2043
200
0.3
I(ENx)
I(ENx)
I(ENx)
I(ENx)
I(INx)
J
Leakage
current
µA
µA
= 0 V
= 0 V
= Hi
–40°C ≤ T ≤ 125°C TPS2053
200
0.3
J
Reverse
leakage
current
TPS2043
IN = high
impedance
T = 25°C
J
TPS2053
undervoltage lockout
TPS2043
TPS2053
TYP MAX
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
MAX
MIN
Low-level input voltage
2
2.5
2
2.5
V
Hysteresis
T = 25°C
J
100
100
mV
overcurrent OCx
TPS2043
TYP
TPS2053
TYP
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
10
MIN
MAX
10
†
Sink current
V
= 5 V
mA
V
O
Output low voltage
I
= 5 mA,
V
V
0.5
1
0.5
1
O
OL(OCx)
= 3.3 V
†
Off-state current
V
= 5 V,
µA
O
O
†
Specified by design, not production tested.
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
PARAMETER MEASUREMENT INFORMATION
OUTx
t
f
t
r
RL
CL
V
90%
10%
O(OUTx)
90%
10%
TEST CIRCUIT
50%
90%
50%
50%
50%
V
V
I(ENx)
I(ENx)
t
off
t
off
t
on
t
on
90%
V
V
O(OUTx)
O(OUTx)
10%
10%
VOLTAGE WAVEFORMS
Figure 1. Test Circuit and Voltage Waveforms
V
I(EN)
(5 V/div)
V
I(EN)
(5 V/div)
V
T
C
= 5 V
= 25°C
= 0.1 µF
V
T
C
= 5 V
= 25°C
= 0.1 µF
I(IN)
A
L
I(IN)
A
L
V
O(OUT)
(2 V/div)
V
O(OUT)
(2 V/div)
0
1000
2000
3000
4000
5000
0
1
2
3
4
5
6
7
8
9
10
t – Time – ms
t – Time – ms
Figure 2. Turnon Delay and Rise Time
Figure 3. Turnoff Delay and Fall Time
with 0.1-µF Load
with 0.1-µF Load
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
PARAMETER MEASUREMENT INFORMATION
V
I(EN)
(5 V/div)
V
I(EN)
(5 V/div)
V
= 5 V
I(IN)
= 25°C
V
= 5 V
I(IN)
= 25°C
T
A
T
A
V
O(OUT)
(2 V/div)
V
C
R
= 1 µF
= 10 Ω
O(OUT)
(2 V/div)
L
L
C
R
= 1 µF
= 10 Ω
L
L
0
1
2
3
4
5
6
7
8
9
10
0
2
4
6
8
10 12 14 16 18 20
t – Time – ms
t – Time – ms
Figure 4. Turnon Delay and Rise Time
Figure 5. Turnoff Delay and Fall Time
with 1-µF Load
with 1-µF Load
V
T
A
= 5 V
I(IN)
= 25°C
V
T
A
= 5 V
I(IN)
= 25°C
V
I(EN)
(5 V/div)
V
O(OUT)
(2 V/div)
I
I
O(OUT)
O(OUT)
(0.5 A/div)
(0.2 A/div)
0
10 20 30 40 50 60 70 80 90 100
t – Time – ms
0
1
2
3
4
5
6
7
8
9
10
t – Time – ms
Figure 6. TPS2043, Short-Circuit Current,
Device Enabled into Short
Figure 7. TPS2043, Threshold Trip Current
with Ramped Load on Enabled Device
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
PARAMETER MEASUREMENT INFORMATION
V
= 5 V
I(IN)
= 25°C
T
A
R
= 10 Ω
L
V
O(OC)
(5 V/div)
V
I(EN)
(5 V/div)
470 µF
220 µF
100 µF
V
= 5 V
I(IN)
Load Ramp,1A/100 ms
= 25°C
I
O(OUT)
(0.5 A/div)
T
A
I
O(OUT)
(o.2 A/div)
0
20 40 60 80 100 120 140 160 180 200
t – Time – ms
0
2
4
6
8
10 12 14 16 18 20
t – Time – ms
Figure 9. Ramped Load on Enabled Device
Figure 8. Inrush Current with 100-µF, 220-µF
and 470-µF Load Capacitance
V
T
= 5 V
V
T
= 5 V
I(IN)
= 25°C
I(IN)
= 25°C
A
A
V
V
O(OC)
(5 V/div)
O(OC)
(5 V/div)
I
I
O(OUT)
(0.5 A/div)
O(OUT)
(1 A/div)
0
400
800
1200
1600
2000
0
20 40 60 80 100 120 140 160 180 200
t – Time – µs
t – Time – µs
Figure 10. 4-Ω Load Connected to Enabled Device
Figure 11. 1-Ω Load Connected
to Enabled Device
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TYPICAL CHARACTERISTICS
TURNON DELAY
vs
TURNOFF DELAY
vs
INPUT VOLTAGE
INPUT VOLTAGE
6
5.5
5
17
16
15
14
13
C
R
T
A
= 1 µF
= 10 Ω
= 25°C
L
L
C
R
T
A
= 1 µF
= 10 Ω
= 25°C
L
L
4.5
4
12
11
10
3
3.5
3
2.5
3
3.5
4
4.5
5
5.5
6
2.5
3
3.5
4
4.5
5
5.5
6
V – Input Voltage – V
I
V – Input Voltage – V
I
Figure 12
Figure 13
RISE TIME
vs
LOAD CURRENT
FALL TIME
vs
LOAD CURRENT
3
3.5
3.3
3.1
V
C
T
A
= 5 V
= 1 µF
= 25°C
I(INx)
L
V
= 5 V
= 25°C
= 1 µF
I(INx)
T
A
C
L
2.9
2.8
2.7
2.9
2.7
2.5
2.6
2.5
0.1 0.2
0.3
0.4 0.5 0.6
0.7
0.8 0.9
0.1 0.2
0.3
0.4
0.5
0.6
0.7
0.8 0.9
I
L
– Load Current – A
I
L
– Load Current – A
Figure 14
Figure 15
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TYPICAL CHARACTERISTICS
SUPPLY CURRENT, OUTPUT ENABLED
SUPPLY CURRENT, OUTPUT DISABLED
vs
vs
JUNCTION TEMPERATURE
JUNCTION TEMPERATURE
200
180
160
2000
1800
V
= 5.5 V
I(INx)
V
= 5.5 V
= 5 V
1600
1400
I(INx)
V
= 5 V
I(INx)
V
I(INx)
V
= 4 V
I(INx)
1200
1000
800
V
I(INx)
= 4 V
V
I(INx)
= 2.7 V
V
= 2.7 V
I(INx)
140
120
100
600
V
= 3.3 V
I(INx)
400
200
0
–200
–50 –25
0
25
50
75 100 125 150
–50 –25
0
25
50
75
100 125 150
T
J
– Junction Temperature – °C
T
J
– Junction Temperature – °C
Figure 16
Figure 17
SUPPLY CURRENT, OUTPUT DISABLED
SUPPLY CURRENT, OUTPUT ENABLED
vs
vs
INPUT VOLTAGE
INPUT VOLTAGE
2000
1600
200
180
160
T
J
= 125°C
T
J
= 125°C
T
J
= 85°C
1200
800
T
J
= 25°C
140
400
0
T
J
= 0°C
T
J
= 25°C
T
4
= 85°C
J
T
J
= –40°C
120
100
T
J
= –40°C
T
J
= 0°C
–400
2.5
3
3.5
4.5
5
5.5
6
2.5
3
3.5
4
4.5
5
5.5
6
V – Input Voltage – V
I
V – Input Voltage – V
I
Figure 19
Figure 18
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TYPICAL CHARACTERISTICS
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
vs
JUNCTION TEMPERATURE
INPUT VOLTAGE
175
150
125
175
150
125
I
O
= 0.5 A
V
= 2.7 V
I(INx)
I
O
= 0.5 A
V
= 3.3 V
I(INx)
T
J
= 125°C
T
J
= 85°C
100
75
100
75
V
I(INx)
= 4.5 V
T
J
= 25°C
T
J
= 0°C
V
I(INx)
= 5 V
T
J
= –40°C
50
–50 –25
50
2.5
0
25
50
75
100 125 150
3
3.5
4
4.5
5
5.5
6
T
J
– Junction Temperature – °C
V – Input Voltage – V
I
Figure 20
Figure 21
INPUT-TO-OUTPUT VOLTAGE
SHORT-CURCUIT OUTPUT CURRENT
vs
vs
LOAD CURRENT
INPUT VOLTAGE
100
0.95
0.9
T
A
= 25°C
T
J
= –40°C
75
50
T
J
= 25°C
V
I(INx)
= 2.7 V
V
I(INx)
= 3.3 V
T
J
= 125°C
0.85
V
= 5 V
I(INx)
25
0
V
I(INx)
= 4.5 V
0.8
0.1
0.2
0.4
– Load Current – A
0.5
0.6
2.5
3
3.5
4
4.5
5
5.5
6
I
L
V – Input Voltage – V
I
Figure 22
Figure 23
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TYPICAL CHARACTERISTICS
THRESHOLD TRIP CURRENT
SHORT CIRCUIT OUTPUT CURRENT
vs
vs
INPUT VOLTAGE
JUNCTION TEMPERATURE
1.2
0.95
0.9
T
= 25°C
A
Load Ramp = 1 A/10 ms
1.175
V
I(INx)
= 5 V
V
I(INx)
= 4 V
1.15
V
I(INx)
= 2.7 V
0.85
1.125
1.1
0.8
2.5
3
3.5
4
4.5
5
5.5
6
–50 –25
0
25
50
75
100
125
V – Input Voltage – V
I
T
J
– Junction Temperature – °C
Figure 24
Figure 25
UNDERVOLTAGE LOCKOUT
vs
CURRENT-LIMIT RESPONSE
vs
JUNCTION TEMPERATURE
PEAK CURRENT
2.5
2.4
500
450
400
V
T
A
= 5 V
I(INx)
= 25°C
350
300
250
Start Threshold
Stop Threshold
2.3
2.2
200
150
100
50
2.1
2
0
–50 –25
0
25
50
75
100 125 150
0
2.5
5
7.5
10
12.5
T
J
– Junction Temperature – °C
Peak Current – A
Figure 26
Figure 27
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
TYPICAL CHARACTERISTICS
OVERCURRENT RESPONSE TIME (OCx)
vs
PEAK CURRENT
8
6
4
V
T
A
= 5 V
I(INx)
= 25°C
2
0
0
2.5
5
7.5
10
12.5
Peak Current – A
Figure 28
APPLICATION INFORMATION
2
Power Supply
2.7 V to 5.5 V
IN1
15
6
Load
Load
Load
OUT1
OUT2
OUT3
NC
IN2
0.1 µF
0.1 µF
22 µF
22 µF
14
16
OC1
OC2
OC3
NC
13
12
11
10
9
0.1 µF
22 µF
3
EN1
EN2
EN3
NC
4
7
8
1
5
GND1
GND2
Figure 29. Typical Application
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
power-supply considerations
A 0.01-µF to 0.1-µF ceramic bypass capacitor between INx and GND, close to the device, is recommended.
Placing a high-value electrolytic capacitor on the output pin(s) is recommended when the output load is heavy.
This precaution reduces power-supply transients that may cause ringing on the input. Additionally, bypassing
the output with a 0.01-µF to 0.1-µF ceramic capacitor improves the immunity of the device to short-circuit
transients.
overcurrent
A sense FET checks for overcurrent conditions. Unlike current-sense resistors, sense FETs do not increase the
series resistance of the current path. When an overcurrent condition is detected, the device maintains a
constant output current and reduces the output voltage accordingly. Complete shutdown occurs only if the fault
is present long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted before the
device is enabled or before V
and immediately switch into a constant-current output.
hasbeenapplied(seeFigure6). TheTPS2043andTPS2053sensetheshort
I(INx)
In the second condition, the excessive load occurs while the device is enabled. At the instant the excessive load
occurs, very high currents may flow for a short time before the current-limit circuit can react. After the
current-limit circuit has tripped (reached the overcurrent trip threshhold) the device switches into
constant-current mode.
In the third condition, the load has been gradually increased beyond the recommended operating current. The
current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is
exceeded (see Figure 7). The TPS2043 and TPS2053 are capable of delivering current up to the current-limit
threshold without damaging the device. Once the threshold has been reached, the device switches into its
constant-current mode.
OC response
The OC open-drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed.
Connectingaheavycapacitiveloadtoanenableddevicecancausemomentaryfalseovercurrentreportingfrom
the inrush current flowing through the device, charging the downstream capacitor. An RC filter of 500 µs (see
Figure 30) can be connected to the OC pin to reduce false overcurrent reporting. Using low-ESR electrolytic
capacitors on the output lowers the inrush current flow through the device during hot-plug events by providing
a low impedance energy source, thereby reducing erroneous overcurrent reporting.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
OC response (continued)
V+
V+
R
pullup
R
pullup
TPS2043
TPS2043
GND1
R
filter
To USB
Controller
GND1
OC1
OUT1
OUT2
OC2
OC1
OUT1
OUT2
OC2
OC3
OUT3
NC
IN1
IN1
C
filter
EN1
EN2
EN1
EN2
GND2
GND2
OC3
OUT3
NC
IN2
EN3
NC
IN2
EN3
NC
NC
NC
Figure 30. Typical Circuit for OC Pin and RC Filter for Damping Inrush OC Responses
power dissipation and junction temperature
The low on-resistance on the n-channel MOSFET allows small surface-mount packages, such as SOIC, to pass
large currents. The thermal resistances of these packages are high compared to those of power packages; it
is good design practice to check power dissipation and junction temperature. The first step is to find r
the input voltage and operating temperature. As an initial estimate, use the highest operating ambient
at
DS(on)
temperature of interest and read r
from Figure 21. Next, calculate the power dissipation using:
DS(on)
2
P
r
I
D
DS(on)
Finally, calculate the junction temperature:
T
P
R
T
J
D
JA
A
Where:
T = Ambient Temperature °C
A
θJA
R
= Thermal resistance SOIC = 172°C/W
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get an acceptable answer.
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
thermal protection
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extendedperiodsoftime. ThefaultsforcetheTPS2043andTPS2053intoconstantcurrentmode, whichcauses
the voltage across the high-side switch to increase; under short-circuit conditions, the voltage across the switch
is equal to the input voltage. The increased dissipation causes the junction temperature to rise to high levels.
The protection circuit senses the junction temperature of the switch and shuts it off. Hysteresis is built into the
thermal sense circuit, and after the device has cooled approximately 20 degrees, the switch turns back on. The
switch continues to cycle in this manner until the load fault or input power is removed.
The TPS2043 and TPS2053 implement a dual thermal trip to allow fully independent operation of the power
distribution switches. In an overcurrent or short-circuit condition the junction temperature will rise. Once the die
temperature rises to approximately 140°C, the internal thermal sense circuitry checks which power switch is
in an overcurrent condition and turns that power switch off, thus isolating the fault without interrupting operation
of the adjacent power switch. Should the die temperature exceed the first thermal trip point of 140°C and reach
160°C, both switches turn off. The OC open-drain output is asserted (active low) when overtemperature or
overcurrent occurs.
undervoltage lockout (UVLO)
Anundervoltagelockoutensuresthatthepowerswitchisintheoffstateatpowerup. Whenevertheinputvoltage
falls below approximately 2 V, the power switch will be quickly turned off. This facilitates the design of
hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The
UVLO will also keep the switch from being turned on until the power supply has reached at least 2 V, even if
the switch is enabled. Upon reinsertion, the power switch will be turned on with a controlled rise time to reduce
EMI and voltage overshoots.
universal serial bus (USB) applications
The universal serial bus (USB) interface is a 12-Mb/s, or 1.5-Mb/s, multiplexed serial bus designed for
low-to-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). The four-wire USB
interface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for
differential data, and two lines are provided for 5-V power distribution.
USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power
is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V
from the 5-V input or its own internal power supply.
The USB specification defines the following five classes of devices, each differentiated by power-consumption
requirements:
Hosts/self-powered hubs (SPH)
Bus-powered hubs (BPH)
Low-power, bus-powered functions
High-power, bus-powered functions
Self-powered functions
Self-powered and bus-powered hubs distribute data and power to downstream functions. The TPS2043 and
TPS2053 can provide power-distribution solutions for many of these classes of devices.
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
host/self-powered and bus-powered hubs
Hosts and self-powered hubs have a local power supply that powers the embedded functions and the
downstream ports (see Figure 31). This power supply must provide from 5.25 V to 4.75 V to the board side of
the downstream connection under full-load and no-load conditions. Hosts and SPHs must have current-limit
protection and must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs,
monitors, printers, and stand-alone hubs.
Downstream
USB Ports
Power Supply
D+
D–
3.3 V
5 V
V
BUS
+
TPS2043
33 µF
GND
2
IN1
IN2
15
OUT1
6
D+
0.1 µF
D–
V
14
11
OUT2
OUT3
BUS
+
33 µF
GND
†
11
OC1
EN1
OC2
EN2
OC3
EN3
NC
3
D+
D–
†
13
4
USB
Controller
V
BUS
GND
+
†
12
7
33 µF
10
NC
9
8
NC
GND1 GND2
1
5
†
An RC filter may be needed, see Figure 36
Figure 31. Typical Three-Port USB Host/Self-Powered Hub
Bus-powered hubs obtain all power from upstream ports and often contain an embedded function. The hubs
are required to power up with less than one unit load. The BPH usually has one embedded function, and power
is always available to the controller of the hub. If the embedded function and hub require more than 100 mA
on power up, the power to the embedded function may need to be kept off until enumeration is completed. This
can be accomplished by removing power or by shutting off the clock to the embedded function. Power switching
the embedded function is not necessary if the aggregate power draw for the function and controller is less than
one unit load. The total current drawn by the bus-powered device is the sum of the current to the controller, the
embedded function, and the downstream ports, and it is limited to 500 mA from an upstream port.
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
low-power bus-powered functions and high-power bus-powered functions
Both low-power and high-power bus-powered functions obtain all power from upstream ports; low-power
functions always draw less than 100 mA, and high-power functions must draw less than 100 mA at power up
and can draw up to 500 mA after enumeration. If the load of the function is more than the parallel combination
of 44 Ω and 10 µF at power up, the device must implement inrush current limiting (see Figure 32).
Power Supply
D+
D–
3.3 V
TPS2043
2
6
IN1
IN2
V
BUS
Internal
Function
15
14
OUT1
GND
10 µF
0.1 µF
0.1 µF
10 µF
10 µF
0.1 µF
Internal
Function
OUT2
OUT3
NC
3
EN1
EN2
EN3
NC
4
7
11
10
8
Internal
Function
0.1 µF
10 µF
USB
Control
16
OC1
OC2
OC3
NC
13
12
1
5
GND1
GND2
9
Figure 32. High-Power Bus-Powered Function
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
USB power-distribution requirements
USB can be implemented in several ways, and, regardless of the type of USB device being developed, several
power distribution features must be implemented.
Hosts/self-powered hubs must:
–
–
Current-limit downstream ports
Report overcurrent conditions on USB V
BUS
Bus-powered hubs must:
–
–
–
Enable/disable power to downstream ports
Power up at <100 mA
Limit inrush current (<44 Ω and 10 µF)
Functions must:
–
–
Limit inrush currents
Power up at <100 mA
The feature set of the TPS2043 and TPS2053 allows them to meet each of these requirements. The integrated
current-limiting and overcurrent reporting is required by hosts and self-powered hubs. The logic-level enable
and controlled rise times meet the need of both input and output ports on bus-power hubs, as well as the input
ports for bus-power functions (see Figure 39).
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
TUSB2040
Hub Controller
1/2 SN75240
BUSPWR
Tie to TPS2041 EN Input
Downstream
Ports
Upstream
Port
A
B
C
D
GANGED
DP1
DM1
D +
D –
DP0
DM0
D +
D –
Ferrite Beads
A
B
C
D
GND
5 V
GND
SN75240
DP2
DM2
TPS2041
†
47 µF
5 V Power
Supply
OC
IN
EN
DP3
DM3
5 V
OUT
D +
D –
A
B
C
D
1 µF
Ferrite Beads
TPS76333
IN
1/2 SN75240
GND
DP4
DM4
0.1 µF
4.7 µF
V
3.3 V
GND
5 V
†
CC
4.7 µF
TPS2043
PWRON1
GND
EN1
OC1
OUT1
47 µF
OUT2
IN1
OVRCUR1
PWRON2
OVRCUR2
EN2
OC2
D +
D –
48-MHz
Crystal
XTAL1
XTAL2
Ferrite Beads
0.1 µF
GND
5 V
Tuning
Circuit
EN3
OC3
PWRON3
OUT3
IN2
OVRCUR3
†
47 µF
OCSOFF
GND
0.1 µF
GND1
GND2
†
USB rev 1.1 requires 120 µF per hub.
Figure 33. Hybrid Self/Bus-Powered Hub Implementation
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
APPLICATION INFORMATION
generic hot-plug applications (see Figure 34)
In many applications it may be necessary to remove modules or pc boards while the main unit is still operating.
These are considered hot-plug applications. Such implementations require the control of current surges seen
by the main power supply and the card being inserted. The most effective way to control these surges is to limit
and slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply
normally turns on. Due to the controlled rise times and fall times of the TPS2043 and TPS2053, these devices
can be used to provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature
oftheTPS2043andTPS2053alsoensurestheswitchwillbeoffafterthecardhasbeenremoved, andtheswitch
will be off during the next insertion. The UVLO feature guarantees a soft start with a controlled rise time for every
insertion of the card or module.
PC Board
TPS2043
GND1 OC1
Block of
Circuitry
IN1
OUT1
EN1 OUT2
Block of
Circuitry
EN2
GND2
IN2
OC2
Power
Supply
OC3
Block of
Circuitry
OUT3
2.7 V to 5.5 V
0.1 µF
1000 µF
Optimum
EN3
Overcurrent Response
Figure 34. Typical Hot-Plug Implementation
By placing the TPS2043 and TPS2053 between the V
input and the rest of the circuitry, the input power will
CC
reach these devices first after insertion. The typical rise time of the switch is approximately 2.5 ms, providing
a slow voltage ramp at the output of the device. This implementation controls system surge currents and
provides a hot-plugging mechanism for any device.
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS2043, TPS2053
TRIPLE POWER-DISTRIBUTION SWITCHES
SLVS191 – JANUARY 1999
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
0.010 (0,25)
M
14
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°–8°
0.044 (1,12)
A
0.016 (0,40)
Seating Plane
0.004 (0,10)
0.010 (0,25)
0.004 (0,10)
0.069 (1,75) MAX
PINS **
8
14
16
DIM
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MAX
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
A MIN
4040047/D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
24
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明