TPS22962 [TI]
具有输出放电功能的 5.5V、10A、4.4mΩ 负载开关;型号: | TPS22962 |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有输出放电功能的 5.5V、10A、4.4mΩ 负载开关 开关 |
文件: | 总30页 (文件大小:8627K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
TPS22962 5.5V,10A,4.4mΩ 导通电阻负载开关
1 特性
3 说明
1
•
•
•
•
集成单通道负载开关
TPS22962 是一款小型,超低 RON,单通道负载开
关,此开关具有受控接通功能。 此器件包含一个可在
0.8V 至 5.5V 输入电压范围内运行的 N 通道金属氧化
物半导体场效应晶体管 (MOSFET),并且支持最大
10A 的持续电流。
VBIAS 电压范围:2.5V 至 5.5V
VIN 电压范围:0.8V 至 5.5V
超低 RON 电阻
–
VIN = 5V (VBIAS = 5V) 时,RON = 4.4mΩ
•
•
•
•
10A 最大持续开关电流
器件的超低 RON 和高电流处理能力的组合使得此器件
非常适合于驱动具有非常严格压降耐受的处理器电源
轨。 器件的受控上升时间大大减少了由大容量负载电
容导致的涌入电流,从而减少或消除了电源损耗。 此
开关可由 ON 端子单独控制,此端子能够与微控制器
或低压离散逻辑电路生成的低压控制信号直接对接。
通过集成一个在开关关闭时实现快速输出放电 (QOD)
的 224Ω 下拉电阻器,此器件进一步减少总体解决方
案尺寸。
低静态电流(VBIAS = 5V 时为 20µA)
低关断电流(VBIAS = 5V 时为 1µA)
低控制输入阀值允许使用 1.2V 或更高电压的通用
输入输出 (GPIO) 接口
•
V
BIAS 和 VIN 范围内的受控和固定转换率
VIN = 5V (VBIAS = 5V) 时,tR = 2663µs
–
•
•
快速输出放电 (QOD)
带有散热焊盘的小外形尺寸无引线 (SON) 8 端子封
装
TPS22962 采用小型 3mm x 3mm 超薄小外形尺寸无
引线 (WSON)-8 封装 (DNY)。 DNY 封装集成有一个
散热焊盘,此散热焊盘可在高电流和高温应用中实现高
功率耗散。 器件在自然通风环境下的额定运行温度范
围为 -40°C 至 85°C。
•
静电放电 (ESD) 性能经测试符合 JESD 22 规范
–
–
2kV 人体模式 (HBM)
1kV 充电器件模型 (CDM)
2 应用范围
•
•
•
•
•
•
服务器
器件信息(1)
医疗
产品型号
TPS22962
封装
WSON (8)
封装尺寸(标称值)
电信系统
计算
3.00mm x 3.00mm
(1) 如需了解所有可用封装,请见数据表末尾的可订购产品附录。
工业系统
高电流电压轨
4 简化电路原理图
VBIAS
(2.5 V to 5.5 V)
RON 与 VIN 之间的关系 (VBIAS = 5V,IOUT = -200mA)
6
5.5
5
VIN
VOUT
Power
Supply
Load
CIN
CL
ON
GND
ON
TPS22962
OFF
4.5
4
3.5
-40C
3
25C
2.5
85C
2
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8
DG007
1
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
English Data Sheet: SLVSCN3
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
目录
8.1 Overview ................................................................. 14
8.2 Functional Block Diagram ....................................... 14
8.3 Feature Description................................................. 14
8.4 Device Functional Modes........................................ 15
Applications and Implementation ...................... 16
9.1 Application Information............................................ 16
9.2 Typical Application .................................................. 16
1
2
3
4
5
6
7
特性.......................................................................... 1
应用范围................................................................... 1
说明.......................................................................... 1
简化电路原理图........................................................ 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 3
7.1 Absolute Maximum Ratings ...................................... 3
7.2 Handling Ratings....................................................... 4
7.3 Recommended Operating Conditions....................... 4
7.4 Thermal Information.................................................. 4
7.5 Electrical Characteristics, VBIAS = 5.0 V ................... 5
7.6 Electrical Characteristics, VBIAS = 2.5 V ................... 6
7.7 Switching Characteristics.......................................... 7
7.8 Typical Characteristics.............................................. 9
Detailed Description ............................................ 14
9
10 Power Supply Recommendations ..................... 19
11 Layout................................................................... 19
11.1 Layout Guidelines ................................................. 19
11.2 Layout Example .................................................... 20
12 器件和文档支持 ..................................................... 21
12.1 Trademarks........................................................... 21
12.2 Electrostatic Discharge Caution............................ 21
12.3 术语表 ................................................................... 21
13 机械封装和可订购信息 .......................................... 21
8
5 修订历史记录
Changes from Original (June 2014) to Revision A
Page
•
完整版的最初发布版本。 ....................................................................................................................................................... 1
2
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
6 Pin Configuration and Functions
WSON (DNY) PACKAGE
8 PIN
VOUT
VOUT
1
2
3
4
VIN
8
7
6
5
VOUT
VOUT
8
7
6
5
VIN
VIN
1
2
3
4
VIN
VIN
(Exposed thermal
pad)
VIN
(Exposed thermal
pad)
VBIAS
ON
VOUT
GND
VBIAS
ON
VOUT
GND
Top View
Bottom View
Pin Functions
PIN
I/O
DESCRIPTION
NAME
NO.
Switch input. Place ceramic bypass capacitor(s) between this pin and GND. See the Detailed
Description section for more information.
VIN
1, 2
I
I
Exposed thermal
Pad
Switch input. Place ceramic bypass capacitor(s) between this pin and GND. See the Detailed
Description section for more information.
VIN
VBIAS
ON
3
4
5
I
I
Bias voltage. Power supply to the device.
Active high switch control input. Do not leave floating.
Ground.
GND
–
Switch output. Place ceramic bypass capacitor(s) between this pin and GND. See the Detailed
Description section for more information.
VOUT
6, 7, 8
O
7 Specifications
7.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted)(1)
MIN
–0.3
–0.3
–0.3
–0.3
MAX
6
UNIT
V
VIN
Input voltage range
VBIAS
VOUT
VON
IMAX
IPLS
TJ
Bias voltage range
6
V
Output voltage range
6
V
ON pin voltage range
6
V
Maximum Continuous Switch Current, TA = 70°C
Maximum Pulsed Switch Current, pulse < 300 µs, 2% duty cycle
Maximum junction temperature
10
12
125
A
A
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Copyright © 2014, Texas Instruments Incorporated
3
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
UNIT
7.2 Handling Ratings
MIN
–65
MAX
150
Tstg
Storage temperature range
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins(1)
0
0
2
1
V(ESD)
Electrostatic discharge
kV
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VBIAS
5.5
UNIT
V
VIN
Input voltage range
Bias voltage range
ON voltage range
Output voltage range
0.8
2.5
0
VBIAS
VON
VOUT
V
5.5
V
VIN
V
VIH, ON High-level voltage, ON
VIL, ON Low-level voltage, ON
VBIAS = 2.5 V to 5.5 V
VBIAS = 2.5 V to 5.5 V
1.2
0
5.5
V
0.5
V
TA
Operating free-air temperature range
Input Capacitor
–40
1(1)
85
°C
µF
CIN
(1) Refer to Detailed Description section.
7.4 Thermal Information
TPS22962
THERMAL METRIC(1)
UNIT
DNY
8 PINS
RθJA
Junction-to-ambient thermal resistance
44.6
44.4
17.6
0.4
RθJCtop
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ψJB
17.4
1.1
RθJCbot
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
7.5 Electrical Characteristics, VBIAS = 5.0 V
Unless otherwise noted, the specification in the following table applies over the operating ambient temperature
–40°C ≤ TA ≤ 85°C (Full) and VBIAS = 5.0 V. Typical values are for TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX UNIT
CURRENTS AND THRESHOLDS
IOUT = 0, VIN = VBIAS
VON = 5.0 V
,
IQ, VBIAS
VBIAS quiescent current
VBIAS shutdown current
Full
Full
20.4
1.1
26.0
µA
µA
ISD, VBIAS
VON = 0 V, VOUT = 0 V
1.5
0.1
0.1
0.1
0.1
0.1
0.1
VIN = 5.0 V
VIN = 3.3 V
VIN = 1.8 V
VIN = 1.05 V
VIN = 0.8 V
VON = 0 V,
VOUT = 0 V
ISD, VIN
VIN shutdown current
Full
µA
ION
ON pin leakage current
ON pin hysteresis
VON = 5.5 V
VBIAS = VIN
Full
µA
VHYS, ON
25°C
113
4.4
4.4
4.4
4.4
4.4
4.4
224
mV
RESISTANCE CHARACTERISTICS
25°C
Full
5.0
5.6
5.0
5.6
5.0
5.6
5.0
5.6
5.0
5.6
5.0
5.6
233
VIN = 5.0 V
VIN = 3.3 V
VIN = 2.5 V
VIN = 1.8 V
VIN = 1.05 V
VIN = 0.8 V
mΩ
mΩ
mΩ
mΩ
mΩ
25°C
Full
25°C
Full
IOUT = –200 mA,
VBIAS = 5.0 V
RON
On-state resistance
25°C
Full
25°C
Full
25°C
Full
mΩ
RPD
Output pulldown resistance
VIN = 5.0 V, VON = 0 V, VOUT = 1 V
Full
Ω
Copyright © 2014, Texas Instruments Incorporated
5
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
7.6 Electrical Characteristics, VBIAS = 2.5 V
Unless otherwise noted, the specification in the following table applies over the operating ambient temperature
–40°C ≤ TA ≤ 85°C (Full) and VBIAS = 2.5 V. Typical values are for TA = 25°C unless otherwise noted.
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX UNIT
CURRENTS AND THRESHOLDS
IOUT = 0, VIN = VBIAS
VON = 5.0 V
,
IQ, VBIAS
VBIAS quiescent current
VBIAS shutdown current
Full
Full
9.9
0.5
12.5
µA
µA
ISD, VBIAS
VON = 0 V, VOUT = 0 V
0.65
0.1
0.1
0.1
0.1
0.1
VIN = 2.5 V
VIN = 1.8 V
VIN = 1.05 V
VIN = 0.8 V
VON = 0 V,
VOUT = 0 V
ISD, VIN
VIN shutdown current
Full
µA
ION
ON pin input leakage current
ON pin hysteresis
VON = 5.5 V
VBIAS = VIN
Full
µA
VHYS, ON
25°C
83
4.7
4.6
4.5
4.5
224
mV
RESISTANCE CHARACTERISTICS
25°C
Full
5.3
6.0
5.2
5.8
5.1
5.7
5.1
5.7
233
VIN =2.5 V
VIN =1.8 V
VIN =1.05 V
VIN = 0.8 V
mΩ
mΩ
mΩ
25°C
Full
IOUT = –200 mA,
VBIAS = 2.5 V
RON
On-state resistance
25°C
Full
25°C
Full
mΩ
RPD
Output pulldown resistance
VIN = 2.5 V, VON = 0 V, VOUT = 1 V
Full
Ω
6
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
7.7 Switching Characteristics
Refer to the timing test circuit in Figure 1 (unless otherwise noted) for references to external components used for the test
condition in the switching characteristics table. Switching characteristics shown below are only valid for the power-up
sequence where VIN and VBIAS are already in steady state condition before the ON pin is asserted high.
PARAMETER
TEST CONDITION
MIN
TYP
MAX UNIT
VIN = 5 V, VON = VBIAS = 5 V, TA = 25ºC (unless otherwise noted)
tON
tOFF
tR
Turn-on time
Turn-off time
VOUT rise time
VOUT fall time
Delay time
2397
4
RL = 10 Ω, CL = 0.1 µF
2663
2
µs
tF
tD
1009
VIN = 3.3 V, VON = VBIAS = 5 V, TA = 25ºC (unless otherwise noted)
tON
tOFF
tR
Turn-on time
Turn-off time
VOUT rise time
VOUT fall time
Delay time
1811
4
RL = 10 Ω, CL = 0.1 µF
1756
2
µs
µs
µs
µs
µs
tF
tD
897
VIN = 0.8 V, VON = VBIAS = 5 V, TA = 25ºC (unless otherwise noted)
tON
tOFF
tR
Turn-on time
Turn-off time
VOUT rise time
VOUT fall time
Delay time
981
4
RL = 10 Ω, CL = 0.1 µF
500
2
tF
tD
714
VIN = 2.5 V, VON = 5 V, VBIAS = 2.5 V, TA = 25ºC (unless otherwise noted)
tON
tOFF
tR
Turn-on time
Turn-off time
VOUT rise time
VOUT fall time
Delay time
1576
8
RL = 10Ω, CL = 0.1 µF
1372
2
tF
tD
865
VIN = 1.8V, VON = 5 V, VBIAS = 2.5 V, TA = 25ºC (unless otherwise noted)
tON
tOFF
tR
Turn-on time
Turn-off time
VOUT rise time
VOUT fall time
Delay time
1343
7
RL = 10 Ω, CL = 0.1 µF
1006
2
tF
tD
815
VIN = 0.8 V, VON = 5V, VBIAS = 2.5 V, TA = 25ºC (unless otherwise noted)
tON
tOFF
tR
Turn-on time
Turn-off time
VOUT rise time
VOUT fall time
Delay time
994
8
RL = 10 Ω, CL = 0.1 µF
502
2
tF
tD
723
Copyright © 2014, Texas Instruments Incorporated
7
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
VIN
ON
VOUT
GND
CIN = 1µF
C
L
+
-
R
L
ON
(A)
TPS22962
OFF
GND
GND
(1) Rise and fall times of the control signal is 100ns.
Figure 1. Test Circuit
VON
50%
50%
tF
tOFF
tR
tON
90%
90%
VOUT
50%
50%
VOUT
10%
10%
10%
tD
Figure 2. Timing Waveforms
8
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
7.8 Typical Characteristics
25
20
15
10
5
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-40C
25C
85C
-40C
25C
85C
0
2.5
3
3.5
4
4.5
5
5.5
2.5
3
3.5
4
4.5
5
5.5
VBIAS (V)
DG001
VBIAS (V)
DG002
VIN = VBIAS
VON = 5 V
IOUT = 0 A
VIN = VBIAS
VON = 0 V
VOUT = 0 V
Figure 3. IQ,VBIAS vs VBIAS
Figure 4. ISD,VBIAS vs VBIAS
6.0
0.03
5.5
5.0
4.5
4.0
3.5
3.0
0.025
0.02
0.015
0.01
0.005
0
-40C
25C
85C
VIN = 0.8V
VIN =1.2V
VIN =1.8V
VIN = 1.05V
VIN =1.5V
VIN =2.5V
10
35
60
85
110
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8
±40
±15
DG003_5V
Junction Temperature (C)
C006
VBIAS = 5 V
VON = 0 V
VOUT = 0 V
VBIAS = 2.5 V
VON = 5 V
IOUT = –200 mA
Figure 5. ISD,VIN vs VIN
Figure 6. RON vs Junction Temperature
6.0
6
5.5
5
5.5
5.0
4.5
4.0
3.5
3.0
4.5
4
3.5
3
-40C
25C
85C
2.4
VIN = 0.8V
VIN = 1.2V
VIN = 2.5V
VIN = 4.2V
VIN = 1.05V
VIN = 1.8V
VIN = 3.3V
VIN =5V
2.5
2
10
35
60
85
110
0.8
1
1.2
1.4
1.6
1.8
2
2.2
±40
±15
DG006
VIN (V)
Junction Temperature (C)
C006
VBIAS = 5 V
VON = 5 V
IOUT = –200 mA
VBIAS = 2.5 V
VON = 5 V
IOUT = –200 mA
Figure 7. RON vs Junction Temperature
Figure 8. RON vs VIN
Copyright © 2014, Texas Instruments Incorporated
9
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
Typical Characteristics (continued)
6
5.5
5
6
5.5
5
4.5
4
4.5
4
3.5
3
3.5
3
-40C
25C
VBIAS = 2.5V
VBIAS = 5V
2.5
2
2.5
2
85C
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8
DG007
DG012
VBIAS = 5 V
VON = 5 V
IOUT = –200 mA
TA = 25°C
VON = 5 V
IOUT = –200 mA
Figure 9. RON vs VIN
Figure 10. RON vs VIN
7
240
235
230
225
220
215
210
205
200
6
5
4
3
2
-40°C
25°C
85°C
-40C
25C
85C
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
5.25 5.5
VIN (V)
C002
DG016
VBIAS (V)
VBIAS = 2.5 V
VON = 5 V
IOUT = –10 A
VON = 0 V
VIN = 1.05 V
VOUT = 1 V
Figure 12. RON vs VIN at 10A load
Figure 11. RPD vs VBIAS
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
VIN = 0.8V
VIN = 1.05V
VIN =1.2V
VIN =1.5V
VIN =1.8V
VIN =2.5V
-40°C
25°C
85°C
0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8
VIN (V)
1
2
3
4
5
6
7
8
9
10
IOUT (A)
C001
C002
VBIAS = 5 V
VON = 5 V
IOUT = –10 A
VBIAS = 2.5 V
VON = 5 V
TA = 25°C
Figure 13. RON vs VIN at 10A load
Figure 14. RON vs IOUT
10
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
Typical Characteristics (continued)
6.5
0.14
0.12
0.1
VIN = 0.8V
VIN = 1.2V
VIN = 1.8V
VIN = 3.3V
VIN = 1.05V
VIN = 1.5V
VIN = 2.5V
VIN = 4.2V
6.0
5.5
5.0
4.5
4.0
3.5
3.0
VIN =5V
0.08
0.06
0.04
0.02
0
-40C
25C
85C
1
2
3
4
5
6
7
8
9
10
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
5.25 5.5
DG017HYS
IOUT (A)
VON = 5 V
C001
VBIAS (V)
VBIAS = 5 V
TA = 25°C
VIN = VBIAS
Figure 15. RON vs IOUT
Figure 16. VHYS vs VBIAS
1.2
1.2
1.1
1
1.1
1
0.9
0.8
0.7
0.6
0.5
0.9
0.8
0.7
0.6
0.5
-40C
25C
85C
-40C
25C
85C
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
5.25 5.5
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
5.25 5.5
DG098
DG017H
VBIAS (V)
VBIAS (V)
VIN = VBIAS
IOUT = 0 A
VIN = VBIAS
IOUT = 0 A
Figure 17. VIL,ON vs VBIAS
Figure 18. VIH,ON vs VBIAS
1000
1200
1100
1000
900
800
700
600
500
400
900
800
700
600
500
400
-40C
25C
85C
-40C
25C
85C
0.8
1.05
1.3
1.55
VIN (V)
1.8
2.05
2.3
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8
DG018
DG019
VBIAS = 2.5 V
RL = 10 Ω
CL = 0.1 µF
VBIAS = 5 V
RL = 10 Ω
CL = 0.1 µF
Figure 19. tD vs VIN
Figure 20. tD vs VIN
Copyright © 2014, Texas Instruments Incorporated
11
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
Typical Characteristics (continued)
4
4
3
2
1
0
3
2
1
0
-40C
25C
85C
-40C
25C
85C
0.8
1.05
1.3
1.55
VIN (V)
1.8
2.05
2.05
2.05
2.3
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4
4
4.4 4.8
DG020
DG021
VBIAS = 2.5 V
RL = 10 Ω
CL = 0.1 µF
VBIAS = 5 V
RL = 10 Ω
CL = 0.1 µF
Figure 21. tF vs VIN
Figure 22. tF vs VIN
12
11
10
9
6
5
4
3
2
8
7
-40C
25C
85C
-40C
25C
85C
6
5
4
0.8
1.05
1.3
1.55
VIN (V)
1.8
2.3
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4.4 4.8
DG022
DG024
VBIAS = 2.5 V
RL = 10 Ω
CL = 0.1 µF
VBIAS = 5 V
RL = 10 Ω
CL = 0.1 µF
Figure 23. tOFF vs VIN
Figure 24. tOFF vs VIN
1800
3000
1600
1400
1200
1000
800
2500
2000
1500
1000
500
-40C
25C
85C
-40C
25C
85C
600
0.8
1.05
1.3
1.55
VIN (V)
1.8
2.3
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4.4 4.8
DG025
DG026
VBIAS = 2.5 V
RL = 10 Ω
CL = 0.1 µF
VBIAS = 5 V
RL = 10 Ω
CL = 0.1 µF
Figure 25. tON vs VIN
Figure 26. tON vs VIN
12
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
Typical Characteristics (continued)
1600
3000
2500
2000
1500
1000
500
1400
1200
1000
800
-40C
25C
85C
-40C
25C
85C
600
400
0
0.8
1.05
1.3
1.55
VIN (V)
1.8
2.05
2.3
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8
DG027
DG028
VBIAS = 2.5 V
RL = 10 Ω
CL = 0.1 µF
VBIAS = 5 V
RL = 10 Ω
CL = 0.1 µF
Figure 27. tR vs VIN
Figure 28. tR vs VIN
3500
VIN = 0.8V
VIN =1.2V
VIN =1.8V
VIN =3.3V
VIN =4.2V
VIN = 1.05V
VIN =1.5V
VIN =2.5V
VIN =3.6V
VIN =5.0V
3750
3250
2750
2250
1750
1250
750
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
750
VBIAS = 2.5V
VBIAS = 3.3V
VBIAS = 3.6V
VBIAS = 4.2V
VBIAS = 5.0V
VBIAS = 5.5V
250
500
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
5.25 5.5
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
VIN (V)
4
4.4 4.8 5.2
VBIAS (V)
DG030
DG023
TA = 25°C
RL = 10 Ω
CL = 0.1 µF
TA = 25°C
RL = 10 Ω
CL = 0.1 µF
Figure 30. tR vs VBIAS for Various VIN
Figure 29. tR vs VIN for Various VBIAS
Copyright © 2014, Texas Instruments Incorporated
13
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
8 Detailed Description
8.1 Overview
The device is a 5.5 V, 10 A load switch in a 8-pin SON package. To reduce voltage drop for low voltage and high
current rails, the device implements an ultra-low resistance N-channel MOSFET which reduces the drop out
voltage through the device.
The device has a controlled and fixed slew rate which helps reduce or eliminate power supply droop due to large
inrush currents. During shutdown, the device has very low leakage currents, thereby reducing unnecessary
leakages for downstream modules during standby. Integrated control logic, driver, charge pump, and output
discharge FET eliminates the need for any external components, which reduces solution size and bill of materials
(BOM) count.
8.2 Functional Block Diagram
VIN
Charge
Pump
VBIAS
Control
Logic
Driver
ON
VOUT
GND
8.3 Feature Description
8.3.1 On/off Control
The ON pin controls the state of the load switch, and asserting the pin high (active high) enables the switch. The
ON pin is compatible with standard GPIO logic threshold and can be used with any microcontroller or discrete
logic with 1.2-V or higher GPIO voltage. This pin cannot be left floating and must be tied either high or low for
proper functionality.
14
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
Feature Description (continued)
8.3.2 Input Capacitor (CIN)
To limit the voltage drop on the input supply caused by transient in-rush currents when the switch turns on into a
discharged load capacitor or short-circuit, a capacitor needs to be placed between VIN and GND. A 1-µF ceramic
capacitor, CIN, placed close to the pins, is usually sufficient. Higher values of CIN can be used to further reduce
the voltage drop in high-current application. When switching heavy loads, it is recommended to have an input
capacitor 10 times higher than the output capacitor to avoid excessive voltage drop; however, a 10 to 1 ratio for
capacitance is not required for proper functionality of the device, but a ratio smaller than 10 to 1 (such as 1 to 1)
could cause a VIN dip upon turn-on due to inrush currents based on external factor such as board parasitics and
output bulk capacitance.
8.3.3 Output Capacitor (CL)
Due to the integrated body diode in the N-channel MOSFET, a CIN greater than CL is highly recommended. A CL
greater than CIN can cause VOUT to exceed VIN when the system supply is removed. This could result in current
flow through the body diode from VOUT to VIN. A CIN to CL ratio of 10 to 1 is recommended for minimizing VIN
dip caused by inrush currents during startup, however a 10 to 1 ratio for capacitance is not required for proper
functionality of the device. A ratio smaller than 10 to 1 (such as 1 to 1) could cause a VIN dip upon turn-on due to
inrush currents based on external factor such as board parasitics and output bulk capacitance.
8.3.4 VIN and VBIAS Voltage Range
For optimal RON performance, make sure VIN ≤ VBIAS. The device may still be functional if VIN > VBIAS but it will
exhibit RON greater than what is listed in the Electrical Characteristics table. See Figure 31 for an example of a
typical device. Notice the increasing RON as VIN increases. Be sure to never exceed the maximum voltage rating
for VIN and VBIAS. Performance of the device is not guaranteed for VIN > VBIAS
.
10
VBIAS = 2.5V
VBIAS = 3.3V
VBIAS = 4.2V
VBIAS =5.5V
VBIAS = 3.0V
VBIAS = 3.6V
VBIAS =5.0V
9
8
7
6
5
4
3
0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
4
4.4 4.8 5.2
DG055
VIN (V)
Figure 31. RON vs VIN (VIN > VBIAS
)
8.4 Device Functional Modes
Table 1 shows the connection of VOUT depending on the state of the ON pin.
Table 1. VOUT Connection
ON
L
VOUT
GND
VIN
H
Copyright © 2014, Texas Instruments Incorporated
15
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
9 Applications and Implementation
9.1 Application Information
This section will highlight some of the design considerations when implementing this device in various
applications. A PSPICE model for this device is also available in the product page of this device on www.ti.com
for further aid.
9.2 Typical Application
This application demonstrates how the TPS22962 can be used to power downstream modules with large
capacitances. The example below is powering a 100-µF capacitive output load.
VIN
VOUT
VIN
VOUT
VIN
(exposed
pad)
CIN
CL = 100µF
VBIAS
VBIAS
GND
ON
ON
Figure 32. Typical Application Schematic for Powering a Downstream Module
9.2.1 Design Requirements
For this design example, use the following as the input parameters.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
VIN
VBIAS
5.0 V
5.0 V
10 A
Load current
9.2.2 Detailed Design Procedure
To begin the design process, the designer needs to know the following:
•
•
•
VIN voltage
VBIAS voltage
Load current
9.2.2.1 VIN to VOUT Voltage Drop
The VIN to VOUT voltage drop in the device is determined by the RON of the device and the load current. The
RON of the device depends upon the VIN and VBIAS conditions of the device. Refer to the RON specification of the
device in the Electrical Characteristics table of this datasheet. Once the RON of the device is determined based
upon the VIN and VBIAS conditions, use Equation 1 to calculate the VIN to VOUT voltage drop:
DV = ILOAD ´RON
(1)
where
•
•
•
ΔV = voltage drop from VIN to VOUT
ILOAD = load current
RON = On-resistance of the device for a specific VIN and VBIAS combination
An appropriate ILOAD must be chosen such that the IMAX specification of the device is not violated.
16
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
9.2.2.2 Inrush Current
To determine how much inrush current will be caused by the CL capacitor, use Equation 2:
dVOUT
I
= CL ´
INRUSH
dt
(2)
where
•
•
•
•
IINRUSH = amount of inrush caused by CL
CL = capacitance on VOUT
dt = time it takes for change in VOUT during the ramp up of VOUT when the device is enabled
dVOUT = change in VOUT during the ramp up of VOUT when the device is enabled
An appropriate CL value should be placed on VOUT such that the IMAX and IPLS specficiations of the device are
not violated.
Figure 33. Inrush Current (VBIAS = 5 V, VIN = 5 V, CL = 100 µF)
9.2.2.3 Thermal Considerations
The maximum IC junction temperature should be restricted to 125°C under normal operating conditions. To
calculate the maximum allowable dissipation, PD(max) for a given output current and ambient temperature, use
Equation 3.
TJ(MAX) - TA
=
P
D(MAX)
θJA
(3)
where
•
•
•
•
PD(max) = maximum allowable power dissipation
TJ(max) = maximum allowable junction temperature (125°C for the TPS22962)
TA = ambient temperature of the device
θJA = junction to air thermal impedance. See Thermal Information section. This parameter is highly
dependent upon board layout.
Copyright © 2014, Texas Instruments Incorporated
17
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
9.2.3 Application Curves
VBIAS = 5 V
CL = 0.1 µF
VIN = 5 V
CIN = 1 µF
CIN = 1 µF
CIN = 1 µF
VBIAS = 5 V
CL = 0.1 µF
VIN = 1.05 V
CIN = 1 µF
Figure 34. tR at VBIAS = 5 V
Figure 35. tR at VBIAS = 5 V
VBIAS = 2.5 V
CL = 0.1 µF
VIN = 2.5 V
VBIAS = 2.5 V
CL = 0.1 µF
VIN = 1.05 V
CIN = 1 µF
Figure 36. tR at VBIAS = 2.5 V
Figure 37. tR at VBIAS = 2.5 V
VBIAS = 5 V
CL = 0.1 µF
VIN = 5 V
VBIAS = 5 V
CL = 0.1 µF
VIN = 2.5 V
CIN = 1 µF
Figure 38. tF at VBIAS = 5 V
Figure 39. tF at VBIAS = 5 V
18
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
VBIAS = 2.5 V
CL = 0.1 µF
VIN = 2.5 V
CIN = 1 µF
VBIAS = 2.5 V
CL = 0.1 µF
VIN = 0.8 V
CIN = 1 µF
Figure 40. tF at VBIAS = 2.5 V
Figure 41. tF at VBIAS = 2.5 V
10 Power Supply Recommendations
The device is designed to operate from a VBIAS range of 2.5 V to 5.5 V and VIN range of 0.8 V to 5.5 V. This
supply must be well regulated and placed as close to the device pin as possible with the recommended 1µF
bypass capacitor. If the supply is located more than a few inches from the device pins, additional bulk
capacitance may be required in addition to the ceramic bypass capacitors. If additional bulk capacitance is
required, an electrolytic, tantalum, or ceramic capacitor of 10 µF may be sufficient.
11 Layout
11.1 Layout Guidelines
•
•
•
VIN and VOUT traces should be as short and wide as possible to accommodate for high current.
Use vias under the exposed thermal pad for thermal relief for high current operation.
The VIN pin should be bypassed to ground with low ESR ceramic bypass capacitors. The typical
recommended bypass capacitance is 1-µF ceramic with X5R or X7R dielectric. This capacitor should be
placed as close to the device pins as possible.
•
•
The VOUT pin should be bypassed to ground with low ESR ceramic bypass capacitors. The typical
recommended bypass capacitance is one-tenth of the VIN bypass capacitor of X5R or X7R dielectric rating.
This capacitor should be placed as close to the device pins as possible.
The VBIAS pin should be bypassed to ground with low ESR ceramic bypass capacitors. The typical
recommended bypass capacitance is 0.1-µF ceramic with X5R or X7R dielectric.
Copyright © 2014, Texas Instruments Incorporated
19
TPS22962
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
www.ti.com.cn
11.2 Layout Example
VIA to Power Ground Plane
VIA to VIN Plane
VIN Bypass
VIN
Capacitor
VIN
VOUT Bypass
Capacitor
VIN
To Bias Supply
VBIAS
ON
GND
To GPIO
control
Exposed Thermal
Figure 42. Recommended Board Layout
20
Copyright © 2014, Texas Instruments Incorporated
TPS22962
www.ti.com.cn
ZHCSCL1A –JUNE 2014–REVISED JUNE 2014
12 器件和文档支持
12.1 Trademarks
All trademarks are the property of their respective owners.
12.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.3 术语表
SLYZ022 — TI 术语表。
这份术语表列出并解释术语、首字母缩略词和定义。
13 机械封装和可订购信息
以下页中包括机械封装和可订购信息。 这些信息是针对指定器件可提供的最新数据。 这些数据会在无通知且不对
本文档进行修订的情况下发生改变。 欲获得该数据表的浏览器版本,请查阅左侧的导航栏。
Copyright © 2014, Texas Instruments Incorporated
21
重要声明
德州仪器(TI) 及其下属子公司有权根据 JESD46 最新标准, 对所提供的产品和服务进行更正、修改、增强、改进或其它更改, 并有权根据
JESD48 最新标准中止提供任何产品和服务。客户在下订单前应获取最新的相关信息, 并验证这些信息是否完整且是最新的。所有产品的销售
都遵循在订单确认时所提供的TI 销售条款与条件。
TI 保证其所销售的组件的性能符合产品销售时 TI 半导体产品销售条件与条款的适用规范。仅在 TI 保证的范围内,且 TI 认为 有必要时才会使
用测试或其它质量控制技术。除非适用法律做出了硬性规定,否则没有必要对每种组件的所有参数进行测试。
TI 对应用帮助或客户产品设计不承担任何义务。客户应对其使用 TI 组件的产品和应用自行负责。为尽量减小与客户产品和应 用相关的风险,
客户应提供充分的设计与操作安全措施。
TI 不对任何 TI 专利权、版权、屏蔽作品权或其它与使用了 TI 组件或服务的组合设备、机器或流程相关的 TI 知识产权中授予 的直接或隐含权
限作出任何保证或解释。TI 所发布的与第三方产品或服务有关的信息,不能构成从 TI 获得使用这些产品或服 务的许可、授权、或认可。使用
此类信息可能需要获得第三方的专利权或其它知识产权方面的许可,或是 TI 的专利权或其它 知识产权方面的许可。
对于 TI 的产品手册或数据表中 TI 信息的重要部分,仅在没有对内容进行任何篡改且带有相关授权、条件、限制和声明的情况 下才允许进行
复制。TI 对此类篡改过的文件不承担任何责任或义务。复制第三方的信息可能需要服从额外的限制条件。
在转售 TI 组件或服务时,如果对该组件或服务参数的陈述与 TI 标明的参数相比存在差异或虚假成分,则会失去相关 TI 组件 或服务的所有明
示或暗示授权,且这是不正当的、欺诈性商业行为。TI 对任何此类虚假陈述均不承担任何责任或义务。
客户认可并同意,尽管任何应用相关信息或支持仍可能由 TI 提供,但他们将独力负责满足与其产品及在其应用中使用 TI 产品 相关的所有法
律、法规和安全相关要求。客户声明并同意,他们具备制定与实施安全措施所需的全部专业技术和知识,可预见 故障的危险后果、监测故障
及其后果、降低有可能造成人身伤害的故障的发生机率并采取适当的补救措施。客户将全额赔偿因 在此类安全关键应用中使用任何 TI 组件而
对 TI 及其代理造成的任何损失。
在某些场合中,为了推进安全相关应用有可能对 TI 组件进行特别的促销。TI 的目标是利用此类组件帮助客户设计和创立其特 有的可满足适用
的功能安全性标准和要求的终端产品解决方案。尽管如此,此类组件仍然服从这些条款。
TI 组件未获得用于 FDA Class III(或类似的生命攸关医疗设备)的授权许可,除非各方授权官员已经达成了专门管控此类使 用的特别协议。
只有那些 TI 特别注明属于军用等级或“增强型塑料”的 TI 组件才是设计或专门用于军事/航空应用或环境的。购买者认可并同 意,对并非指定面
向军事或航空航天用途的 TI 组件进行军事或航空航天方面的应用,其风险由客户单独承担,并且由客户独 力负责满足与此类使用相关的所有
法律和法规要求。
TI 已明确指定符合 ISO/TS16949 要求的产品,这些产品主要用于汽车。在任何情况下,因使用非指定产品而无法达到 ISO/TS16949 要
求,TI不承担任何责任。
产品
应用
www.ti.com.cn/telecom
数字音频
www.ti.com.cn/audio
www.ti.com.cn/amplifiers
www.ti.com.cn/dataconverters
www.dlp.com
通信与电信
计算机及周边
消费电子
能源
放大器和线性器件
数据转换器
DLP® 产品
DSP - 数字信号处理器
时钟和计时器
接口
www.ti.com.cn/computer
www.ti.com/consumer-apps
www.ti.com/energy
www.ti.com.cn/dsp
工业应用
医疗电子
安防应用
汽车电子
视频和影像
www.ti.com.cn/industrial
www.ti.com.cn/medical
www.ti.com.cn/security
www.ti.com.cn/automotive
www.ti.com.cn/video
www.ti.com.cn/clockandtimers
www.ti.com.cn/interface
www.ti.com.cn/logic
逻辑
电源管理
www.ti.com.cn/power
www.ti.com.cn/microcontrollers
www.ti.com.cn/rfidsys
www.ti.com/omap
微控制器 (MCU)
RFID 系统
OMAP应用处理器
无线连通性
www.ti.com.cn/wirelessconnectivity
德州仪器在线技术支持社区
www.deyisupport.com
IMPORTANT NOTICE
邮寄地址: 上海市浦东新区世纪大道1568 号,中建大厦32 楼邮政编码: 200122
Copyright © 2014, 德州仪器半导体技术(上海)有限公司
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS22962DNYR
TPS22962DNYT
ACTIVE
ACTIVE
WSON
WSON
DNY
DNY
8
8
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 85
-40 to 85
962A0
962A0
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS22962DNYR
TPS22962DNYT
WSON
WSON
DNY
DNY
8
8
3000
250
330.0
180.0
12.4
12.4
3.3
3.3
3.3
3.3
1.0
1.0
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS22962DNYR
TPS22962DNYT
WSON
WSON
DNY
DNY
8
8
3000
250
367.0
213.0
367.0
191.0
38.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
WSON - 0.8 mm max height
PLASTIC QUAD FLATPACK- NO LEAD
DNY0008A
3.15
2.85
A
B
PIN 1 INDEX AREA
3.15
2.85
C
0.8
0.7
SEATING PLANE
0.08 C
0.05
0.00
1.6±0.1
SYMM
0.5
0.3
EXPOSED THERMAL
PAD
5X
(0.2) TYP
6X 0.65
4
5
SYMM
2X
1.95
2.4±0.1
0.35
0.25
8X
0.1
C A B
C
8
1
0.05
PIN1 ID
(OPTIONAL)
2X (0.2)
0.5
0.3
4221022/E 06/2020
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for optimal thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
WSON - 0.8 mm max height
PLASTIC QUAD FLATPACK- NO LEAD
DNY0008A
(1.6)
5X (0.6)
5X (0.3)
SYMM
(0.6)
1
8
3X (0.65)
SYMM
(1.6)
(0.325)
(2.4)
(0.95)
(0.975)
5
4
(R0.05) TYP
(0.55)
(2.8)
(Ø0.2) VIA
TYP
LAND PATTERN EXAMPLE
SCALE: 20X
0.07 MAX
0.07 MIN
ALL AROUND
ALL AROUND
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
EXPOSED METAL
NON- SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4221022/E 06/2020
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271)
.
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
WSON - 0.8 mm max height
DNY0008A
PLASTIC QUAD FLATPACK- NO LEAD
2X (1.47)
SYMM
5X (0.6)
5X (0.3)
(0.6)
8
1
(0.325)
(1.6)
(0.63)
SYMM
2X
(1.06)
(0.975)
5
3X (0.65)
4
(R0.05) TYP
METAL
TYP
(2.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD
81% PRINTED COVERAGE BY AREA
SCALE: 20X
4221022/E 06/2020
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com.cn/zh-cn/legal/termsofsale.html) 或 ti.com.cn 上其他适用条款/TI 产品随附的其他适用条款
的约束。TI 提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2021 德州仪器半导体技术(上海)有限公司
相关型号:
©2020 ICPDF网 联系我们和版权申明