TPS53219ARGTT [TI]
Wide Input Voltage, Eco-modeâ¢, Single Synchronous Step-Down Controller; 宽输入电压，生态modeâ ?? ¢ ，单同步降压型控制器
| 型号： | TPS53219ARGTT |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Wide Input Voltage, Eco-modeâ¢, Single Synchronous Step-Down Controller |
| 文件： | 总26页 (文件大小：1060K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
Wide Input Voltage, Eco-mode™, Single Synchronous Step-Down Controller
Check for Samples: TPS53219A
1
FEATURES
POINT-OF-LOAD APPLICATIONS
2
•
Conversion Input Voltage Range: 3 V to 28 V
VDD Input Voltage Range: 4.5 V to 25 V
Output Voltage Range: 0.6 V to 5.5 V
Wide Output Load Range: 0 A to > 20 A
Built-In 0.6-V (±0.8%) Reference
•
•
•
•
Storage Computer
Server Computer
•
•
•
•
•
•
Multi-Function Printer
Embedded Computing
DESCRIPTION
The TPS53219A is
Built-In LDO Linear Voltage Regulator
a small-sized single buck
Auto-Skip Eco-mode™ for Light-Load
controller with adaptive on-time D-CAP™ mode
control. The device is suitable for low output voltage,
high current, PC system power rail and similar
point-of-load (POL) power supplies in digital
consumer products. The small package and minimal
pin-count save space on the PCB, while the
dedicated EN pin and pre-set frequency selections
simplify the power supply design. The skip-mode at
light load conditions, strong gate drivers and low-side
FET RDS(on) current sensing supports low-loss and
high efficiency, over a broad load range. The
conversion input voltage (high-side FET drain
voltage) range is between 4.5 V and 25 V, and the
output voltage range is between 0.6 V and 5.5 V. The
TPS53219A is available in a 16-pin, QFN package
specified from –40°C to 85°C.
Efficiency
•
•
D-CAP™ Mode with 100-ns Load-Step
Response
Adaptive On-Time Control Architecture with 8
Selectable Frequency Settings
•
•
4700ppm/°C RDS(on) Current Sensing
0.7-ms, 1.4-ms, 2.8-ms and 5.6-ms Selectable
Internal Voltage Servo Soft-Start
•
•
•
•
•
•
•
Pre-Charged Start-up Capability
Built-In Output Discharge
Open-Drain Power Good Output
Integrated Boost Switch
Built-in OVP/UVP/OCP
Thermal Shutdown (Non-latch)
3 mm × 3 mm QFN, 16-Pin (RGT) Package
VOUT
VIN
VREG
VIN
VIN
TG
SW
SW
SW
BG
CSD86350
16
15
14
13
PGOOD NC VBST DRVH
SW 12
1
TRIP
DRVL 11
VDRV 10
EN
2
3
4
EN
TPS53219A
VFB
RF
TGR
VREG
9
Pad MODE VDD
GND PGND
PGND
5
6
7
8
UDG-11273
VDD
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
Eco-mode, D-CAP are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
ORDERING DEVICE
NUMBER
MINIMUM
QUANTITY
TA
PACKAGE
PINS
OUTPUT SUPPLY
ECO PLAN
TPS53219ARGTR
TPS53219ARGTT
16
16
Tape and reel
Mini-reel
3000
250
Green (RoHS and
no Pb/Br)
–40°C to 85°C Plastic QFN (RGT)
ABSOLUTE MAXIMUM RATINGS(1)
over operating free-air temperature range (unless otherwise noted)
VALUE
–0.3 to 37
–0.3 to 7
–0.3 to 28
–2.0 to 30
–7
UNIT
VBST
VBST(2)
VDD
Input voltage range
V
DC
SW
Pulse <20ns, E = 5 µJ
VDRV, EN, TRIP, VFB, RF, MODE
DRVH
DRVH(2)
Output voltage range
DRVL, VREG
–0.3 to 7
–2.0 to 37
–0.3 to 7
–0.5 to 7
–0.3 to 7
150
V
PGOOD
TJ
Junction temperature range
Storage temperature range
°C
°C
TSTG
–55 to 150
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Voltage values are with respect to the SW terminal
THERMAL INFORMATION
TPS53219A
THERMAL METRIC(1)
UNITS
16-PIN RGT
51.3
θJA
Junction-to-ambient thermal resistance
θJCtop
θJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
85.4
20.1
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
1.3
ψJB
19.4
θJCbot
6.0
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
2
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
–0.1
4.5
TYP
MAX
34.5
25
UNIT
VBST
VDD
Input voltage range
SW
VBST(1)
–1.0
–0.1
–0.1
–1.0
–0.1
–0.3
–0.1
–40
28
V
6.5
6.5
34.5
6.5
6.5
6.5
85
EN, TRIP, VFB, RF, VDRV, MODE
DRVH
DRVH(1)
Output voltage range
TA
V
DRVL, VREG
PGOOD
Operating free-air temperature
°C
(1) Voltage values are with respect to the SW terminal.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
over operating free-air temperature range, VDD = 12 V (Unless otherwise noted)
PARAMETER
SUPPLY CURRENT
CONDITIONS
MIN
TYP
MAX UNIT
VDD current, TA = 25°C, No Load, VEN = 5 V,
VVFB = 0.630 V
IVDD
VDD supply current
420
590
10
µA
µA
IVDDSDN
VDD shutdown current
VDD current, TA=25°C, No Load, VEN=0 V
INTERNAL REFERENCE VOLTAGE
VVFB
VVFB
IVFB
VFB regulation voltage
VFB regulation voltage
VFB input current
VFB voltage, CCM condition(1)
TA = 25°C
600
600
mV
mV
µA
597
595.2
594
603
604.8
606
0°C ≤ TA≤ 85°C
600.0
600
-40°C ≤ TA≤ 85°C
VVFB = 0.630V, TA = 25°C
0.002
0.200
OUTPUT DRIVERS
Source, IDRVH = –50 mA
Sink, IDRVH = 50 mA
Source, IDRVL = –50 mA
Sink, IDRVL = 50 mA
1.5
0.7
1.0
0.5
17
3
1.8
2.2
1.2
30
RDRVH
RDRVL
tDEAD
DRVH resistance
Ω
Ω
DRVL resistance
Dead time
DRVH-off to DRVL-on
DRVL-off to DRVH-on
7
ns
10
22
35
LDO OUTPUT
VVREG
IVREG
VDO
LDO output voltage
LDO output current(1)
0 mA ≤ IVREG ≤ 50 mA
5.76
6.20
6.67
50
V
Maximum current allowed from LDO
VVDD = 4.5 V, IVREG = 50 mA
mA
mV
LDO drop out voltage
364
BOOT STRAP SWITCH
VFBST
Forward voltage
VBST leakagecurrent
VVREG-VBST, IF = 10 mA, TA = 25°C
VVBST = 23 V, VSW = 17 V, TA = 25°C
0.1
0.2
1.5
V
IVBSTLK
0.01
µA
DUTY AND FREQUENCY CONTROL
tOFF(min)
tON(min)
SOFTSTART
Minimum off-time
TA = 25°C
150
260
35
400
ns
ns
VIN = 17 V, VOUT = 0.6 V, RRF = 0 Ω to VREG,
TA = 25°C(1)
Minimum on-time
0 V ≤ VOUT ≤ 95%, RMODE = 39 kΩ
0 V ≤ VOUT ≤ 95%, RMODE = 100kΩ
0 V ≤ VOUT ≤ 95%, RMODE = 200 kΩ
0 V ≤ VOUT ≤ 95%, RMODE = 470 kΩ
0.7
1.4
2.8
5.6
tSS
Internal soft-start time
ms
POWERGOOD
PG in from lower
PG in from higher
PG hysteresis
92.5%
108%
2.5%
96.0%
111%
5.0%
98.5%
114%
7.8%
VTHPG
PG threshold
PG transistor
on-resistance
RPG
15
30
1
50
Ω
tPG(del)
PG delay after soft-start
0.8
1.2
ms
(1) Ensured by design. Not production tested.
4
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
ELECTRICAL CHARACTERISTICS
over operating free-air temperature range, VDD = 12 V (Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LOGIC THRESHOLD AND SETTING CONDITIONS
–40°C ≤ TA≤ 85°C
1.8
1.7
EN voltage threshold enable
VEN
0°C ≤ TA≤ 85°C
V
EN voltage threshold disable
0.5
1.0
IEN
EN input current
VEN = 5 V
µA
RRF = 0 Ω to GND, TA = 25°C(1)
RRF = 187 kΩ to GND, TA = 25°C(1)
RRF = 619 kΩ to GND, TA = 25°C(1)
RRF = Open, TA = 25°C(1)
RRF = 866 kΩ to VREG, TA = 25°C(1)
RRF = 309 kΩ to VREG, TA = 25°C(1)
RRF = 124 kΩ to VREG, TA = 25°C(1)
RRF = 0 Ω to VREG, TA = 25°C(1)
200
250
350
450
580
670
770
880
250
300
400
500
650
750
850
970
300
350
450
550
720
820
930
1070
fSW
Switching frequency
kHz
VO DISCHARGE
IDischg
VO discharge current
VEN = 0 V, VSW = 0.5 V
5
9
13
mA
PROTECTION: CURRENT SENSE
ITRIP
TRIP source current
VTRIP = 1 V, TA = 25°C
TA = 25°C(2)
10
11
µA
ppm/°C
V
TCITRIP
VTRIP
TRIP current temp. coef.
4700
Current limit threshold setting range VTRIP-GND voltage
VTRIP = 3.0 V
0.2
355
185
17
3
395
215
33
375
200
25
VOCL
Current limit threshold
VTRIP = 1.6 V
VTRIP = 0.2 V
VTRIP = 3.0 V
VTRIP = 1.6 V
VTRIP = 0.2 V
Positive
mV
–406
–215
–33
3
–375
–200
–25
15
–355
–185
–17
VOCLN
Negative current limit threshold
Auto zero cross adjustable range
mV
mV
VAZC(adj)
Negative
–15
–3
PROTECTION: UVP AND OVP
VOVP
OVP trip threshold voltage
OVP detect
115% 120% 125%
1
tOVP(del)
VUVP
OVP propagation delay time
VFB delay with 50-mV overdrive
UVP detect
µs
Output UVP trip threshold voltage
Output UVP propagation delay time
Output UVP enable delay time
65%
0.8
70%
1
75%
1.2
tUVP(del)
tUVP(en)
UVLO
ms
ms
from EN to UVP workable, RMODE = 39 kΩ
2.00
2.55
3.00
Wake up
4.00
4.18
0.25
4.50
VUVVREG
VREG UVLO threshold
V
Hysteresis
THERMAL SHUTDOWN
TSDN Thermal shutdown threshold
Shutdown temperature(2)
Hysteresis(2)
145
10
°C
(1) Not production tested. Test conditions are VIN = 12 V, VOUT = 1.1 V, IOUT =10 A and using the application circuit shown in Figure 17 and
Figure 18.
(2) Ensured by design. Not production tested
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
DEVICE INFORMATION
RGT PACKAGE
16 PINS
(TOP VIEW)
16
15
14
13
1
2
3
4
12
11
10
9
TRIP
EN
SW
DVRL
VDRV
VREG
TPS53219A
VFB
RF
5
6
7
8
PIN FUNCTIONS
PIN
NAME
PIN
NO.
DESCRIPTION
I/O/P(1)
High-side MOSFET driver output. The SW node referenced floating driver. The gate drive voltage is defined
by the voltage across VBST to SW node bootstrap flying capacitor.
DRVH
13
11
O
O
Synchronous MOSFET driver output. The PGND referenced driver. The gate drive voltage is defined by
VDRV voltage.
DRVL
EN
2
7
I
Enable pin. Place a 1-kΩ resistor in series with this pin if the source voltage is higher than 5.5 V.
GND
G
Ground pin. This is the ground of internal analog circuitry. Connect to GND plane at single point.
Soft-start and skip/CCM selection. Connect a resistor to select soft-start time using Table 1 . The soft-start
time is detected and stored into internal register during start-up.
MODE
NC
5
15
16
8
I
–
O
G
I
No connection.
Open drain power good flag. Provides 1-ms start up delay after the VFB pin voltage falls within specified
limits. When VFB goes out specified limits PGOOD goes low after a 2-µs delay.
PGOOD
PGND
RF
Power ground. Connect to GND plane.
Switching frequency selection. Connect a resistor to GND or VREG to select switching frequency using
Table 2. The switching frequency is detected and stored during the startup.
4
SW
12
P
Output of converted power. Connect this pin to the output inductor.
OCL detection threshold setting pin. 10 µA at room temp, 4700ppm/°C current is sourced and set the OCL
trip voltage as follows.
TRIP
1
I
VOCL=VTRIP/8 spacer ( VTRIP ≤ 3 V, VOCL ≤ 375 mV)
Supply input for high-side FET gate driver (boost terminal). Connect a capacitor from this pin to SW-node.
Internally connected to VREG via bootstrap MOSFET switch.
VBST
14
P
VDD
VDRV
VFB
6
10
3
P
I
Controller power supply input. The input range is from 4.5 V to 25 V.
Gate drive supply voltage input. Connect to VREG if using LDO output as gate drive supply.
Output feedback input. Connect this pin to VOUT through a resistor divider.
6.2-V LDO output. This is the supply of internal analog circuitry and driver circuitry.
Thermal pad. Use five vias to connect to GND plane.
I
VREG
Pad
9
O
–
–
(1) I=Input, O=Output, P=Power, G=Ground
6
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
FUNCTIONAL BLOCK DIAGRAM
UV
16 PGOOD
0.6 V –30%
0.6 V +10/15%
+
+
+
+
Delay
OV
0.6 V +20%
0.6 V –5/10%
Control Logic
Enable/SS Control
14 VBST
EN
2
3
PWM
13 DRVH
12 SW
VFB
+
+
+
Ramp Comp
XCON
0.6 V
GND
TRIP
7
1
10 mA
+
OCP
tON
One-
Shot
x(-1/8)
FCCM
x(1/8)
+
ZC
10 VDRV
11 DRVL
Auto-skip
Auto-skip/FCCM
8
PGND
Frequency
Setting
EN
RF
4
Detector
LDO Linear
Regulator
TPS53219A
5
9
6
MODE
VREG
VDD
UDG-11274
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS
700
600
500
400
300
200
100
0
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
No Load
1.0
0.5
0.0
VEN = 5 V
VVDD = 12 V
VVFB = 0.63 V
No Load
VEN = 0 V
VVDD = 12 V
−50
−25
0
25
50
75
100
125
150
−50
−25
0
25
50
75
100
125
150
Temperature (°C)
Temperature (°C)
Figure 1. VDD Supply Current vs Temperature
Figure 2. VDD Shutdown Current vs Temperature
140
120
100
80
16
14
12
10
8
60
6
40
4
20
OVP
UVP
2
VVDD = 12 V
100 125 150
0
−50
0
−50
−25
0
25
50
75
100
125
150
−25
0
25
50
75
Temperature (°C)
Temperature (°C)
Figure 3. OVP/UVP Threshold vs Temperature
Figure 4. TRIP Pin Current vs Temperature
1000
100
10
1000
100
10
fSET = 300 kHz
VIN = 12 V
VOUT = 1.1 V
fSET = 500 kHz
VIN = 12 V
VOUT = 1.1 V
FCC Mode
Skip Mode
FCC Mode
Skip Mode
1
0.01
1
0.01
0.1
1
10
100
0.1
1
10
100
Output Current (A)
Output Current (A)
Figure 5. Switching Frequency vs Output Current
Figure 6. Switching Frequency vs Output Current
8
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
1000
1000
100
10
1
100
fSET =750 kHz
VIN = 12 V
VOUT = 1.1 V
fSET =1 MHz
VIN = 12 V
VOUT = 1.1 V
10
1
FCC Mode
Skip Mode
FCC Mode
Skip Mode
0.01
0.1
1
10
100
0.01
0.1
1
10
100
Output Current (A)
Output Current (A)
Figure 7. Switching Frequency vs Output Current
Figure 8. Switching Frequency vs Output Current
1200
1000
800
600
400
200
0
1.120
fSET = 500 kHz
VIN = 12 V
VOUT = 1.1 V
fSET = 1 MHz
1.115
1.110
1.105
1.100
1.095
1.090
1.085
1.080
fSET = 750 kHz
fSET = 500 kHz
fSET = 300 kHz
IOUT =10 A
VIN = 12 V
FCC Mode
Skip Mode
0
1
2
3
4
5
6
0
5
10
15
20
25
Output Voltage (V)
Output Current (A)
Figure 9. Switching Frequency vs Output Voltage
Figure 10. Output Voltage vs Output Current
1.110
1.108
1.106
1.104
1.102
1.100
1.098
1.096
1.094
1.092
1.090
100
90
80
70
60
50
40
30
20
10
0
VIN = 12 V
VOUT = 1.1 V
Skip Mode, fSW = 500 kHz
FCC Mode, fSW = 500 kHz
Skip Mode, fSW = 300 kHz
FCC Mode, fSW = 300 kHz
FCC Mode, No Load
Skip Mode, No Load
All Modes, IOUT = 20 A
fSW = 500 kHz
5
6
7
8
9
10
11
12 13 14 15
0.01
0.1
1
10
100
Input Voltage (V)
Output Current (A)
Figure 11. Output Voltage vs Input Voltage
Figure 12. Efficiency vs Output Current
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Figure 13. Start up Waveform)
Figure 14. Pre-bias Start up Waveform)
Figure 15. Turn Off Waveform
Figure 16. Load Transient Response
10
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
APPLICATION CIRCUIT DIAGRAM
R10
100 kW
R9
0 W
VREG
VIN
PGOOD
R1
CIN
VIN
VIN
TG
SW
SW
SW
BG
C5
0.1 mF
CSD86350
8.25 kW
22 mF x 4
16
15
14
13
DRVH
R8
PGOOD NC
VBST
28.7 kW
L1
1
TRIP
SW 12
0.44 mH
PA0513.441
R11
DRVL 11
VDRV 10
1 kW
VOUT
EN
2
3
EN
TPS53219A
TGR
COUT
VFB
POSCAP
330 mF x 2
PGND
VREG
GND PGND Pad
9
4
RF
MODE
5
VDD
6
R2
10 kW
7
8
R4
C4
4.7 mF
187 kW
C3
1 mF
R5
100 kW
UDG-11275
PGOOD
VDD
Figure 17. Typical Application Circuit Diagram with Power Block
R1
8.25 kW
VIN
R10
100 kW
R9
0 W
CIN
22 mF x 4
VREG
PGOOD
C2
1 nF
C1
VIN
VIN
TG
SW
SW
SW
BG
C5
0.1 mF
CSD86350
0.1 mF
16
15
14
13
DRVH
R8
PGOOD NC
VBST
28.7 kW
L1
R7
10 kW
1
TRIP
SW 12
0.44 mH
PA0513.441
R11
DRVL 11
VDRV 10
1 kW
VOUT
COUT
EN
2
3
EN
TPS53219A
TGR
VFB
Ceramic
100 mF x 4
PGND
R12
VREG
GND PGND Pad
9
4
RF
0 W
R2
MODE
5
VDD
10 kW
6
7
8
R4
187 kW
C4
C3
1 mF
4.7 mF
R5
100 kW
UDG-11276
PGOOD
VDD
Figure 18. Typical Application Circuit Diagram with Ceramic Output Capacitors
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
General Description
The TPS53219A is a high-efficiency, single channel, synchronous buck regulator controller suitable for low output
voltage point-of-load applications in computing and similar digital consumer applications. The device features
proprietary D-CAP™ mode control combined with an adaptive on-time architecture. This combination is ideal for
building modern low duty ratio, ultra-fast load step response DC-DC converters. The output voltage ranges from
0.6 V to 5.5 V. The conversion input voltage range is from 3 V up to 28V. The D-CAP™ mode uses the ESR of
the output capacitor(s) to sense the device current . One advantage of this control scheme is that it does not
require an external phase compensation network. This allows a simple design with a low external component
count. Eight preset switching frequency values can be chosen using a resistor connected from the RF pin to
ground or VREG. Adaptive on-time control tracks the preset switching frequency over a wide input and output
voltage range while allowing the switching frequency to increase at the step-up of the load.
The TPS53219A has a MODE pin to select between auto-skip mode and forced continuous conduction mode
(FCCM) for light load conditions. The MODE pin also sets the selectable soft-start time ranging from 0.7 ms to
5.6 ms as shown in Table 1. The strong gate drivers allow low RDS(on) FETs for high-current applications.
When the device starts (either by EN or VDD UVLO), the TPS53219A sends out a current that detects the
resistance connected to the MODE pin to determine the soft-start time. After that (and before VOUT start to ramp
up) the MODE pin becomes a high-impedance input to determine skip mode or FCCM mode operation. When
the voltage on the MODE pin is higher than 1.3 V, the converter enters into FCCM mode. If the voltage on
MODE pin is less than 1.3 V, then the converter operates in skip mode.
It is recommended to connect the MODE pin to the PGOOD pin if FCCM mode is desired. In this configuration,
the MODE pin is connected to the GND potential through a resistor when the device is detecting the soft-start
time thus correct soft-start time is used. The device starts up in skip mode and only after the PGOOD pin goes
high does the device enter into FCCM mode. When the PGOOD pin goes high there is a transition between skip
mode and FCCM. A minimum off-time of 60 ns on DRVL is provided to avoid a voltage spike on the DRVL pin
caused by parasitic inductance of the driver loop and gate capacitance of the low-side MOSFET.
For proper operation, the MODE pin must not be connected directly to a voltage source.
Enable and Soft-Start
When the EN pin voltage rises above the enable threshold voltage (typically 1.4 V), the controller enters its
start-up sequence. The internal LDO regulator starts immediately and regulates to 6.2 V at the VREG pin. The
controller then uses the first 250 µs to calibrate the switching frequency setting resistance attached to the RF pin
and stores the switching frequency code in internal registers. However, switching is inhibited during this phase. In
the second phase, an internal DAC starts ramping up the reference voltage from 0 V to 0.6 V. Depending on the
MODE pin setting, the ramping up time varies from 0.7 ms to 5.6 ms. Smooth and constant ramp-up of the
output voltage is maintained during start-up regardless of load current.
Table 1. Soft-Start and MODE
MODE
SELECTION
SOFT-START
TIME (ms)
ACTION
RMODE (kΩ)
0.7
1.4
2.8
5.6
0.7
1.4
2.8
5.6
39
100
200
475
39
Auto Skip
Pull down to GND
100
200
475
(1)
Forced CCM
Connect to PGOOD
(1) Device goes into Forced CCM after PGOOD becomes high.
When the EN voltage is higher than 5.5 V, a 1-kΩ series resistor is needed for EN pin
12
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
Adaptive On-Time D-CAP™ Control and Frequency Selection
The TPS53219A does not have a dedicated oscillator that determines switching frequency. However, the device
operates with pseudo-constant frequency by feed-forwarding the input and output voltages into the on-time
one-shot timer. The adaptive on-time control adjusts the on-time to be inversely proportional to the input voltage
and proportional to the output voltage (tON ∝ VOUT/VIN).
This makes the switching frequency fairly constant in steady state conditions over a wide input voltage range.
The switching frequency is selectable from eight preset values by a resistor connected between the RF pin and
GND or between the RF pin and the VREG pin as shown in Table 2. (Leaving the resistance open sets the
switching frequency to 500 kHz.)
Table 2. Resistor and Switching Frequency
SWITCHING
RESISTOR (RRF) CONNECTIONS
FREQUENCY (kHz)
0 Ω to GND
250
300
400
500
650
750
850
970
187 kΩ to GND
619 kΩ to GND
Open
866 kΩ to VREG
309 kΩ to VREG
124 kΩ to VREG
0 Ω to VREG
The off-time is modulated by a PWM comparator. The VFB node voltage (the mid-point of resistor divider) is
compared to the internal 0.6-V reference voltage added with a ramp signal. When both signals match, the PWM
comparator asserts a set signal to terminate the off time (turn off the low-side MOSFET and turn on high-side
MOSFET). The set signal is valid if the inductor current level is below the OCP threshold, otherwise the off time
is extended until the current level falls below the threshold.
Small Signal Model
From small-signal loop analysis, a buck converter using D-CAP™ mode can be simplified as shown in Figure 19.
VIN
TPS53219A
Switching Modulator
DRVH
R1
R2
L
VFB
13
11
VOUT
PWM
Control
Logic
and
3
DRVL
+
IOUT
IIND
Driver
IC
+
0.6 V
ESR
RLOAD
Voltage Divider
VC
COUT
Output
Capacitor
UDG-11277
Figure 19. Simplified Modulator Model
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
The output voltage is compared with the internal reference voltage (ramp signal is ignored here for simplicity).
The PWM comparator determines the timing to turn on the high-side MOSFET. The gain and speed of the
comparator can be assumed high enough to keep the voltage at the beginning of each on cycle substantially
constant.
1
H s =
( )
s´ESR ´C
OUT
(1)
For the loop stability, the 0 dB frequency, ƒ0, defined below must be lower than ¼ of the switching frequency.
f
1
SW
f =
£
0
2p´ESR ´C
4
OUT
(2)
According to the equation above, the loop stability of D-CAP™ mode modulator is mainly determined by the
capacitor chemistry. For example, specialty polymer capacitors (SP-CAP) have an output capacitance on the
order of several 100 µF and ESR in range of 10 mΩ. These yields an f0 on the order of 100 kHz or less and a
more stable loop. However, ceramic capacitors have an ƒ0 at more than 700 kHz, and require special care when
used with this modulator. An application circuit for ceramic capacitor is described in section External Parts
Selection with All Ceramic Output Capacitors.
Ramp Signal
The TPS53219A adds a ramp signal to the 0.6-V reference in order to improve jitter performance. As described
in the previous section, the feedback voltage is compared with the reference information to keep the output
voltage in regulation. By adding a small ramp signal to the reference, the S/N ratio at the onset of a new
switching cycle is improved. Therefore the operation becomes less jittery and more stable. The ramp signal is
controlled to start with –7 mV at the beginning of an on-cycle and becomes 0 mV at the end of an off-cycle in
steady state.
During skip mode operation, when the switching frequency is lower than 70% of the nominal frequency (because
of longer off-time), the ramp signal exceeds 0 mV at the end of the off-time but is clamped at 3 mV to minimize
DC offset.
Light Load Condition in Auto-Skip Operation
While the MODE pin is pulled low via RMODE, TPS53219A automatically reduces the switching frequency at light
load conditions to maintain high efficiency. Detailed operation is described as follows. As the output current
decreases from heavy load condition, the inductor current is also reduced and eventually comes to the point that
its rippled valley touches zero level, which is the boundary between continuous conduction and discontinuous
conduction modes. The synchronous MOSFET is turned off when this zero inductor current is detected. As the
load current further decreases, the converter runs into discontinuous conduction mode (DCM). The on-time is
kept almost the same as it was in the continuous conduction mode so that it takes longer time to discharge the
output capacitor with smaller load current to the level of the reference voltage. The transition point to the light
load operation IO(LL) (i.e., the threshold between continuous and discontinuous conduction mode) can be
calculated as shown in Equation 3.
V
- V
´ V
(
)
OUT OUT
V
IN
1
IN
I
=
´
OUT LL
( )
2´L ´ f
SW
where
•
ƒSW is the PWM switching frequency
(3)
Switching frequency versus output current in the light load condition is a function of L, VIN and VOUT, but it
decreases almost proportionally to the output current from the IO(LL) given in Equation 3. For example, it is 60
kHz at IO(LL)/5 if the frequency setting is 300 kHz.
Adaptive Zero Crossing
The TPS53219A has an adaptive zero crossing circuit which performs optimization of the zero inductor current
detection at skip mode operation. This function pursues ideal low-side MOSFET turning off timing and
compensates inherent offset voltage of the Z-C comparator and delay time of the Z-C detection circuit. It
prevents SW-node swing-up caused by too late detection and minimizes diode conduction period caused by too
early detection. As a result, better light load efficiency is delivered.
14
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
Forced Continuous Conduction Mode
When the MODE pin is tied to PGOOD through a resistor, the controller keeps continuous conduction mode
(CCM) in light load condition. In this mode, switching frequency is kept almost constant over the entire load
range which is suitable for applications need tight control of the switching frequency at a cost of lower efficiency.
Output Discharge Control
When EN becomes low, the TPS53219A discharges output capacitor using internal MOSFET connected
between the SW pin and the PGND pin while the high-side and low-side MOSFETs are maintained in the OFF
state. The typical discharge resistance is 40 Ω. The soft discharge occurs only as EN becomes low. After VREG
becomes low, the internal MOSFET turns off and the discharge function becomes inactive.
Low-Side Driver
The low-side driver is designed to drive high-current low-RDS(on) N-channel MOSFET(s). The drive capability is
represented by its internal resistance, which is 1.0 Ω for VDRV to DRVL and 0.5 Ω for DRVL to GND. A dead
time to prevent shoot through is internally generated between high-side MOSFET off to low-side MOSFET on,
and low-side MOSFET off to high-side MOSFET on. The bias voltage VDRV can be delivered from 6.2 V VREG
supply or from external power source from 4.5 V to 6.5 V. The instantaneous drive current is supplied by an input
capacitor connected between the VDRV and PGND pins.
The average low-side gate drive current is calculated in Equation 4.
I
= C ´ V
´ f
GL
GL
VDRV SW
(4)
When VDRV is supplied by external voltage source, the device continues to be supplied by the VREG pin. There
is no internal connection from VDRV to VREG.
High-Side Driver
The high-side driver is designed to drive high current, low RDS(on) N-channel MOSFET(s). When configured as a
floating driver, the bias voltage is delivered from the VDRV pin supply. The average drive current is calculated
using Equation 5.
I
= C ´ V
´ f
GH
GH
VDRV SW
(5)
The instantaneous drive current is supplied by the flying capacitor between VBST and SW pins. The drive
capability is represented by internal resistance, which is 1.5 Ω for VBST to DRVH and 0.7 Ω for DRVH to SW.
The driving power which needs to be dissipated from TPS53219A package.
PDRV = I + IGH ´ V
)
(
GL
VDRV
(6)
Power Good
The TPS53219A has power-good output that indicates high when switcher output is within the target. The
power-good function is activated after soft-start has finished. If the output voltage becomes within +10% or –5%
of the target value, internal comparators detect power-good state and the power-good signal becomes high after
a 1-ms internal delay. If the output voltage goes outside of +15% or –10% of the target value, the power-good
signal becomes low after two microsecond (2-µs) internal delay. The power-good output is an open drain output
and must be pulled up externally.
In order for the PGOOD logic to be valid, the VDD input must be higher than 1 V. To avoid invalid PGOOD logic
before the TPS53219A is powered up, it is recommended that the PGOOD pin be pulled-up to VREG (either
directly or through a resistor divider if a different pull-up voltage is desired) because VREG remains low when the
device is powered off. The pull-up resistance can be chosen from a standard resistor value between 1 kΩ and
100 kΩ.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
Current Sense and Overcurrent Protection
TPS53219A has cycle-by-cycle overcurrent limiting control. The inductor current is monitored during the OFF
state and the controller maintains the OFF state during the period in that the inductor current is larger than the
overcurrent trip level. In order to provide both good accuracy and cost effective solution, TPS53219A supports
temperature compensated MOSFET RDS(on) sensing. The TRIP pin should be connected to GND through the trip
voltage setting resistor, RTRIP. The TRIP terminal sources ITRIP current, which is 10 µA typically at room
temperature, and the trip level is set to the OCL trip voltage VTRIP as shown in Equation 7. Note that the VTRIP is
limited up to approximately 3 V internally.
V
mV = R
kW ´I
TRIP ( ) TRIP ( ) TRIP ( )
mA
(7)
The inductor current is monitored by the voltage between GND pin and SW pin so that SW pin should be
connected to the drain terminal of the low-side MOSFET properly. ITRIP has 4700 ppm/°C temperature slope to
compensate the temperature dependency of the RDS(on). The GND pin is used as the positive current sensing
node. The GND pin should be connected to the proper current sensing device, (for example, the source terminal
of the low-side MOSFET.)
As the comparison is done during the OFF state, VTRIP sets the valley level of the inductor current. Thus, the load
current at the overcurrent threshold, IOCP, can be calculated as shown in Equation 8.
I
V
- V
´ V
IND ripple
(
(
)
OUT OUT
V
IN
V
V
TRIP
)
1
IN
TRIP
I
=
+
=
+
´
OCP
2
2´L ´ f
SW
8´R
8´R
DS on
)
)
(
(
DS on
( )
( )
(8)
In an overcurrent condition, the current to the load exceeds the current to the output capacitor thus the output
voltage tends to fall down. Eventually, it crosses the undervoltage protection threshold and shuts down. After a
hiccup delay (16 ms with 0.7 ms sort-start), the controller restarts. If the overcurrent condition remains, the
procedure is repeated and the device enters hiccup mode.
During the CCM, the negative current limit (NCL) protects the external FET from carrying too much current. The
NCL detect threshold is set as the same absolute value as positive OCL but negative polarity. Note that the
threshold still represents the valley value of the inductor current.
Overvoltage and Undervoltage Protection
TPS53219A monitors a resistor divided feedback voltage to detect over and under voltage. When the feedback
voltage becomes lower than 70% of the target voltage, the UVP comparator output goes high and an internal
UVP delay counter begins counting. After 1ms, TPS53219A latches OFF both high-side and low-side MOSFETs
drivers. The controller restarts after a hiccup delay (16 ms with 0.7 ms soft-start). This function is enabled 1.5-ms
after the soft-start is completed.
When the feedback voltage becomes higher than 120% of the target voltage, the OVP comparator output goes
high and the circuit latches OFF the high-side MOSFET driver and latches ON the low-side MOSFET driver. The
output voltage decreases. If the output voltage reaches UV threshold, then both high-side MOSFET and low-side
MOSFET driver will be OFF and the device restarts after an hiccup delay. If the OV condition remains, both
high-side MOSFET and low-side MOSFET driver remains OFF until the OV condition is removed.
UVLO Protection
The TPS53219A uses VREG undervoltage lockout protection (UVLO). When the VREG voltage is lower than
3.95 V, the device shuts off. When the VREG voltage is higher than 4.2 V, the device restarts. This is non-latch
protection.
Thermal Shutdown
The TPS53219A uses temperature monitoring. If the temperature exceeds the threshold value (typically 145°C),
the device is shut off. This is non-latch protection.
16
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
External Components Selection
Selecting external components is a simple process using D-CAP™ Mode.
1. CHOOSE THE INDUCTOR
The inductance should be determined to give the ripple current of approximately ¼ to ½ of maximum output
current. Larger ripple current increases output ripple voltage and improves the signal-to-noise ratio and helps
stable operation.
V
- V
´ V
)
V
- V
´ V
OUT OUT
)
(
IN
max
(
OUT
OUT
(
IN
max
(
)
)
1
3
L =
´
=
´
I
´ f
V
I
´ f
V
IN
SW
IN
max
(
OUT
SW
IND ripple
(
max
max
)
)
(
)
(
)
(9)
The inductor also requires a low DCR to achieve good efficiency. It also requires enough room above the peak
inductor current before saturation. The peak inductor current can be estimated in Equation 10.
V
- V
´ V
OUT
)
)
(
IN
max
(
OUT
)
V
1
TRIP
I
=
+
´
IND peak
(
)
8´R
L ´ f
V
IN
SW
DS on
max
( )
(
(10)
2. CHOOSE THE OUTPUT CAPACITOR(S)
When organic semiconductor capacitor(s) or specialty polymer capacitor(s) are used, for loop stability,
capacitance and ESR should satisfy Equation 2. For jitter performance, Equation 11 is a good starting point to
determine ESR.
VOUT ´10mV ´(1-D) 10mV ´L ´ fSW L ´ fSW
=
ESR =
=
W
( )
0.6V ´I
0.6V
60
IND ripple
(
)
where
•
D is the duty factor
•
the required output ripple slope is approximately 10 mV per tSW (switching period) in terms of VFB terminal
voltage
(11)
3. DETERMINE THE VALUE OF R1 AND R2
The output voltage is programmed by the voltage-divider resistor, R1 and R2 shown in Figure 19. R1 is
connected between the VFB pin and the output, and R2 is connected between the VFB pin and GND.
Recommended R2 value is between 10 kΩ and 20 kΩ. Determine R1 using Equation 12.
I
´ESR
æ
ç
ö
÷
IND ripple
(
)
VOUT
-
- 0.6
ç
÷
2
è
ø
R1=
´R2
0.6
(12)
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s) :TPS53219A
TPS53219A
SLUSAU4 –DECEMBER 2011
www.ti.com
External Parts Selection with All Ceramic Output Capacitors
When a ceramic output capacitor is used, the stability criteria in Equation 2 cannot be satisfied. The ripple
injection approach as shown in Figure 18 is implemented to increase the ripple on the VFB pin and make the
system stable. C2 can be fixed at 1 nF. The value of C1 can be selected between 10 nF to 200 nF.
The increased ripple on the VFB pin causes the increase of the VFB DC value. The AC ripple coupled to the
VFB pin has two components, one coupled from SW node and the other coupled from VOUT and they can be
calculated using Equation 13 and Equation 14.
V
- V
OUT
(
)
D
IN
V
=
´
INJ SW
(
)
R7´ C1
f
SW
(13)
(14)
I
IND ripple
(
)
V
= ESR´I
+
)
INJ OUT
(
IND ripple
(
)
8´ COUT ´ fSW
The DC value of VFB can be calculated by Equation 15.
+ V
V
)
(
= 0.6 +
INJ SW
(
INJ OUT
(
)
)
V
FB
2
(15)
(16)
And the resistor divider value can be determined by Equation 16.
- V
V
(
)
OUT
FB
R1=
´R2
V
FB
18
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS53219A
TPS53219A
www.ti.com
SLUSAU4 –DECEMBER 2011
LAYOUT CONSIDERATIONS:
Certain points must be considered before starting a layout work using the TPS53219A.
•
Inductor, VIN capacitor(s), VOUT capacitor(s) and MOSFETs are the power components and should be placed
on one side of the PCB (solder side). Other small signal components should be placed on another side
(component side). At least one inner plane should be inserted, connected to power ground, in order to shield
and isolate the small signal traces from noisy power lines.
•
•
All sensitive analog traces and components such as VFB, PGOOD, TRIP, MODE and RF should be placed
away from high-voltage switching nodes such as SW, DRVL, DRVH or VBST to avoid coupling. Use internal
layer(s) as ground plane(s) and shield feedback trace from power traces and components.
The DC/DC converter has several high-current loops. The area of these loops should be minimized in order to
suppress generating switching noise.
–
–
–
The most important loop to minimize the area of is the path from the VIN capacitor(s) through the high and
low-side MOSFETs, and back to the capacitor(s) through ground. Connect the negative node of the VIN
capacitor(s) and the source of the low-side MOSFET at ground as close as possible.
The second important loop is the path from the low-side MOSFET through inductor and VOUT capacitor(s),
and back to source of the low-side MOSFET through ground. Connect source of the low-side MOSFET
and negative node of VOUT capacitor(s) at ground as close as possible.
The third important loop is of gate driving system for the low-side MOSFET. To turn on the low-side
MOSFET, high current flows from VDRV capacitor through gate driver and the low-side MOSFET, and
back to negative node of the capacitor through ground. To turn off the low-side MOSFET, high current
flows from gate of the low-side MOSFET through the gate driver and PGND of the device, and back to
source of the low-side MOSFET through ground. Connect negative node of VDRV capacitor, source of the
low-side MOSFET and PGND of the device at ground as close as possible.
•
Because the TPS53219A controls output voltage referring to voltage across VOUT capacitor, the high-side
resistor of the voltage divider should be connected to the positive node of VOUT capacitor at the regulatioin
point. The low-side resistor should be connected to the GND (analog ground of the device). The traceꢀfrom
these resistors to the VFB pin should be short and thin. Place on the component side and avoid via(s)
between these resistors and the device.
•
•
Connect the overcurrent setting resistors from the TRIP pin to GND and make the connections as close as
possible to the device. The trace from TRIP pin to resistor and from resistor to GND should avoid coupling to
a high-voltage switching node.
Connect the frequency setting resistor from RF pin to GND, or to the PGOOD pin, and make the connections
as close as possible to the device. The trace from the RF pin to the resistor and from the resistor to GND
should avoid coupling to a high-voltage switching node.
•
•
Connect all GND (analog ground of the device) trace together and connect to power ground or ground plane
with a single via or trace or through a 0-Ω resistor at a quiet point
Connections from gate drivers to the respective gate of the high-side or the low-side MOSFET should be as
short as possible to reduce stray inductance. Use 0.65 mm (25 mils) or wider traceꢀand via(s) of at least 0.5
mm (20 mils) diameter along this trace.
•
•
The PCB trace defined as switch node, which connects to source of high-side MOSFET, drain of low-side
MOSFET and high-voltage side of the inductor, should be as short and wide as possible.
Connect the ripple injection VOUT signal (VOUT side of the C1 capacitor in Figure 18) from the terminal of
ceramic output capacitor. The AC coupling capacitor (C7 in Figure 18 ) can be placed near the device.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s) :TPS53219A
PACKAGE OPTION ADDENDUM
www.ti.com
31-Dec-2011
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS53219ARGTR
TPS53219ARGTT
ACTIVE
ACTIVE
QFN
QFN
RGT
RGT
16
16
3000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS53219ARGTR
TPS53219ARGTT
QFN
QFN
RGT
RGT
16
16
3000
250
330.0
180.0
12.4
12.4
3.3
3.3
3.3
3.3
1.1
1.1
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS53219ARGTR
TPS53219ARGTT
QFN
QFN
RGT
RGT
16
16
3000
250
367.0
210.0
367.0
185.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明