TPS54355-EP [TI]
4.5-V TO 20-V INPUT, 3-A OUTPUT SYNCHRONOUS PWM SWITCHES; 4.5 V至20 V输入， 3 -A输出同步PWM SWITCHES
| 型号： | TPS54355-EP |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 4.5-V TO 20-V INPUT, 3-A OUTPUT SYNCHRONOUS PWM SWITCHES |
| 文件： | 总35页 (文件大小：1246K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
4.5-V TO 20-V INPUT, 3-A OUTPUT SYNCHRONOUS PWM SWITCHES
WITH INTEGRATED FET (SWIFT™)
1
FEATURES
SIMPLIFIED SCHEMATIC
2
•
100-mΩ, 4.5-A Peak MOSFET Switch for High
Efficiency at 3-A Continuous Output Current
Input
Voltage
TPS54356
SYNC
•
•
Use External Low-Side MOSFET or Diode
VIN
Fixed-Output Versions – 1.2 V/1.5 V/1.8 V/
2.5 V/3.3 V/5 V
PWRGD
ENA
BOOT
PH
•
•
•
•
Internally Compensated for Low Parts Count
Synchronize to External Clock
BIAS
Output
Voltage
180° Out-of-Phase Synchronization
LSG
Wide Pulse Width Modulation (PWM)
Frequency – Fixed 250 kHz,
500 kHz, or Adjustable 250 kHz to 700 kHz
PGND
VSENSE
PWRPAD
•
•
Internal Slow Start
Load Protected by Peak Current Limit and
Thermal Shutdown
EFFICIENCY
vs
•
•
Adjustable Undervoltage Lockout
OUTPUT CURRENT
100
16-Pin PowerPAD™ Thin Shrink Small-Outline
Package (TSSOP) (PWP)
V = 6 V
I
95
90
85
80
75
70
65
60
V = 12 V
I
APPLICATIONS
•
Industrial and Commercial Low-Power
Systems
•
•
•
LCD Monitors and TVs
Computer Peripherals
Point-of-Load Regulation for High
Performance DSPs, FPGAs, ASICs, and
Microprocessors
V = 12 V
I
V
= 3.3 V
O
55
50
f
= 500 kHz
s
0
1
2
3
4
I
− Output Current − A
O
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
•
•
•
•
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Available in Military (–55°C/125°C)
Temperature Range(1)
•
•
•
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
(1) Additional temperature ranges are available - contact factory
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
SWIFT, PowerPAD are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2009, Texas Instruments Incorporated
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
DESCRIPTION/ORDERING INFORMATION
The TPS5435x is a medium-output-current synchronous buck PWM converter with an integrated high-side
MOSFET and a gate driver for an optional low-side external MOSFET. Features include a high-performance
voltage error amplifier that enables maximum performance under transient conditions. The TPS5435x has an
undervoltage lockout (UVLO) circuit to prevent start-up until the input voltage reaches a preset value, an internal
slow-start circuit to limit in-rush currents, and a power-good (PWRGD) output to indicate valid output conditions.
The synchronization feature is configurable as either an input or an output for easy 180° out-of-phase
synchronization.
The TPS5435x devices are available in a thermally enhanced 16-pin PowerPAD™ Thin Shrink Small-Outline
Package (TSSOP). TI provides evaluation modules and the SWIFT™ Designer software tool to aid in quickly
achieving high-performance power-supply designs to meet aggressive equipment development cycles.
2
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
PACKAGE
MARKING
TJ
PACKAGE(1)
OUTPUT VOLTAGE
PART NUMBER
Plastic HTSSOP – PWP
Plastic HTSSOP – PWP
Plastic HTSSOP – PWP
Plastic HTSSOP – PWP
Plastic HTSSOP – PWP
Plastic HTSSOP – PWP
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
5 V
TPS54352MPWPREP(2)
TPS54353MPWPREP(2)
TPS54354MPWPREP
TPS54355MPWPREP(2)
TPS54356MPWPREP
TPS54357MPWPREP(2)
TBD
TBD
PMDM
TBD
–55°C to 125°C
PMEM
TBD
(1) The PWP package also is available taped and reeled. Add an R suffix to the device type (i.e., TPS5435xPWPR).
(2) Product preview
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
UNIT
–0.3 V to 21.5 V
VIN
VSENSE
–0.3 V to 8 V
–0.3 V to 8 V
–0.3 V to 4 V
–0.3 V to 4 V
VI(PH) + 8 V
–0.3 V to 8.5 V
–0.3 V to 8.5 V
–0.3 V to 4 V
–0.3 V to 4 V
–0.3 V to 6 V
–0.3 V to 4 V
–1.5 V to 22 V
Internally Limited (A)
10 mA
UVLO
Input voltage range, VI
SYNC
ENA
BOOT
VBIAS
LSG
SYNC
Output voltage range, VO
RT
PWRGD
COMP
PH
PH
Source current, IO
LSG (steady-state current)
COMP, VBIAS
SYNC
3 mA
5 mA
LSG (steady-state current)
PH (steady-state current)
COMP
100 mA
Sink current, IS
500 mA
3 mA
ENA, PWRGD
AGND to PGND
10 mA
Voltage differential
±0.3 V
Operating virtual junction temperature range, TJ
Storage temperature range, Tstg
–55°C to 150°C
–65°C to 150°C
260°C
Lead temperature 1,6 mm (1/16 in) from case for 10 s
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
Electrostatic Discharge (ESD) Protection
MIN
MAX
600
1.5
UNIT
V
Human-Body Model (HBM)
Charged-Device Model (CDM)
kV
Recommended Operating Conditions
MIN
4.5
MAX
20
UNIT
V
TPS54352-6
TPS54357
Input voltage range, VI
6.65
–55
20
Operating junction temperature, TJ
125
°C
Electrical Characteristics
TJ = –55°C to 125°C, VIN = 4.5 V to 20 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Supply Current
Operating current, PH pin open,
No external low side MOSFET, RT = Hi-Z
5
IQ
Quiescent current
mA
Shutdown, ENA = 0 V
1
4.32
6.4
TPS54352-6
TPS54357
TPS54352-6
TPS54357
TPS54352-6
TPS54357
4.48
V
Start threshold
voltage
6.65
3.69
5.45
3.97
5.8
Stop threshold
voltage
VIN
V
350
600
Hysteresis
mV
Output Voltage
TJ = 25°C, IO = 100 mA to 3 A
IO = 100 mA to 3 A
1.88
1.176
1.485
1.47
1.2
1.2
1.5
1.5
1.8
1.8
2.5
2.5
1.212
1.224
1.515
1.53
TPS54352
TPS54353
TPS54354
TPS54355
TJ = 25°C, IO = 100 mA to 3 A
IO = 100 mA to 3 A
TJ = 25°C, IO = 100 mA to 3 A
IO = 100 mA to 3 A
1.782
1.764
2.475
2.45
1.818
1.836
TJ = 25°C, IO = 100 mA to 3 A
IO = 100 mA to 3 A
2.525
V
VO
Output voltage
2.55
3.333
3.366
5.05
TJ = 25°C, VIN = 5.5 V to 20 V,
IO = 100 mA to 3 A
3.267
3.234
4.95
4.9
3.3
3.3
5
TPS54356
TPS54357
VIN = 5.5 V to 20 V, IO = 100 mA to 3 A
TJ = 25°C, VIN = 7.5 V to 20 V,
IO = 100 mA to 3 A
VIN = 7.5 V to 20 V, IO = 100 mA to 3 A
5
5.1
Under Voltage Lockout (UVLO)
Start threshold voltage
1.2
1.1
1.25
V
V
UVLO
Stop threshold voltage
Hysteresis
1.02
100
mV
Bias Voltage (VBIAS)
VBIAS Output voltage
Oscillator (RT)
Internally set PWM switching frequency
IVBIAS = 5 mA, VIN ≥ 12 V
7.5
4.4
7.8
8
V
IVBIAS = 5 mA, VIN = 4.5 V
4.47
4.5
RT grounded
RT open
200
400
425
250
500
500
300
600
575
kHz
kHz
Externally set PWM switching frequency RT = 100 kΩ (1% resistor to AGND)
4
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
Electrical Characteristics (continued)
TJ = –55°C to 125°C, VIN = 4.5 V to 20 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Falling-Edge-Triggered Bidirectional Sync System (SYNC)
SYNC out low-to-high rise time
25 pF to ground
200
5
500
10
ns
ns
(10%/90%)(1)
SYNC out high-to-low fall time
(90%/10%)(1)
25 pF to ground
Delay from rising edge to rising edge of PH
pins, See Figure 19
Falling-edge delay time(1)
180
100
360
°
Minimum input pulse width(1)
RT = 100 kΩ
ns
ns
Delay
RT = 100 kΩ
(falling-edge SYNC to rising-edge PH)(1)
SYNC out high-level voltage
SYNC out low-level voltage
SYNC in low-level threshold
SYNC in high-level threshold
50-kΩ resistor to ground, No pullup resistor
2.5
0.8
V
V
V
V
0.6
2.3
10%
770
Percentage of programmed frequency
VIN = 12 V, TJ = 25°C
VIN = 4.5 V
–10%
225
SYNC in frequency range(1)
kHz
Feed-Forward Modulator (Internal Signal)
Modulator gain
8
±25%
180
Modulator gain variation
Minimum controllable ON time(1)
Maximum duty factor(1)
VSENSE
ns
80%
86%
Input bias current, VSENSE
Enable (ENA)
1
µA
Disable low-level input voltage
0.5
V
fs = 250 kHz, RT = ground(1)
fs = 500 kHz, RT = Hi-Z(1)
fs = 250 kHz, RT = ground(1)
fs = 500 kHz, RT = Hi-Z(1)
fs = 250 kHz, RT = ground(1)
fs = 500 kHz, RT = Hi-Z(1)
fs = 250 kHz, RT = ground(1)
fs = 500 kHz, RT = Hi-Z(1)
fs = 250 kHz, RT = ground(1)
fs = 500 kHz, RT = Hi-Z(1)
fs = 250 kHz, RT = ground(1)
fs = 500 kHz, RT = Hi-Z(1)
3.2
1.6
4
TPS54352
TPS54353
2
4.6
2.3
4.4
2.2
5.9
2.9
5.4
2.7
5
TPS54354
Internal
slow-start time
(10% to 90%)
ms
TPS54355
TPS54356
TPS54357
Pullup current source
Pulldown MOSFET
1.8
10
µA
II(ENA) = 1 mA
0.1
V
Power Good (PWRGD)
Power-good threshold
Rising voltage
97%
4
fs = 250 kHz
Rising-edge delay(1)
ms
fs = 500 kHz
2
Output saturation voltage
PWRGD Output saturation voltage
Open-drain leakage current
Isink = 1 mA, VIN > 4.5 V
Isink = 100 µA, VIN = 0 V
Voltage on PWRGD = 6 V
0.05
0.76
V
V
3
µA
(1) Specified by design, not production tested
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
Electrical Characteristics (continued)
TJ = –55°C to 125°C, VIN = 4.5 V to 20 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Current Limit
Current limit
Current-limit hiccup time(2)
Thermal Shutdown
VIN = 12 V
3.3
4.5
4.5
6.5
A
fs = 500 kHz
ms
Thermal-shutdown trip point(2)
Thermal-shutdown hysteresis(2)
165
7
°C
°C
Low-Side MOSFET Driver (LSG)
Turn-on rise time, (10/90%)(2)
VIN = 4.5 V, Capacitive load = 1000 pF
VIN = 12 V
15
60
7.5
5
ns
ns
Deadtime
VIN = 4.5 V sink/source
VIN = 12 V sink/source
Driver ON resistance
Ω
Output Power MOSFETS (PH)
Phase-node voltage when disabled
DC coinditions and no load, ENA = 0 V
VIN = 4.5 V, Idc = 100 mA
0.5
1.13
1.08
150
100
V
V
1.42
1.38
300
200
Voltage drop, low-side FET and diode
VIN = 12 V, Idc = 100 mA
VIN = 4.5 V, BOOT-PH = 4.5 V, IO = 0.5 A
VIN = 12 V, BOOT-PH = 8V, IO = 0.5 A
rDS(ON)
High-side power MOSFET switch(3)
mΩ
(2) Specified by design, not production tested
(3) Resistance from VIN to PH pins
6
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
PIN ASSIGNMENTS
PWP PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VIN
VIN
UVLO
PWRGD
RT
SYNC
ENA
COMP
BOOT
PH
PH
LSG
THERMAL
PAD
VBIAS
PGND
AGND
VSENSE
NOTE: If there is not a pin 1 indicator, turn device to enable
readingthe symbol from left to right. Pin 1 is at the lower
left corner of the device.
TERMINAL FUNCTIONS
TERMINAL
NAME
DESCRIPTION
NO.
Input supply voltage, 4.5 V to 20 V. Must bypass with a low ESR 10-µF ceramic capacitor. Place cap as
close to device as possible; see Figure 23 for an example.
1, 2
VIN
UVLO
PWRGD
RT
Undervoltage lockout. Connecting an external resistive voltage divider from VIN to the pin overrides the
internal default VIN start and stop thresholds.
3
4
5
Power good output. Open-drain output. A low on the pin indicates that the output is less than the desired
output voltage. There is an internal rising-edge filter on the output of the PWRGD comparator.
Frequency setting. Connect a resistor from RT to AGND to set the switching frequency. Connecting the RT
pin to ground or floating will set the frequency to an internally preselected frequency.
Bidirectional synchronization I/O. SYNC is an output when the RT pin is floating or connected low. The
output is a falling-edge signal out of phase with the rising edge of PH. SYNC may be used as an input to
synchronize to a system clock by connecting to a falling edge signal when an RT resistor is used. See 180°
Out of Phase Synchronization operation in the Application Information section. In all cases, a 10-kΩ resistor
must be tied to the SYNC pin in parallel with ground. For information on how to extend slow start, see the
Enable (ENA) and Internal Slow Start section.
6
SYNC
7
8
9
ENA
Enable. Below 0.5 V, the device stops switching. Float pin to enable.
Error amplifier output. Do not connect anything to this pin.
Feedback
COMP
VSENSE
Analog ground. Internally connected to the sensitive analog ground circuitry. Connect to PGND and
PowerPAD package.
10
AGND
Power ground. Noisy internal ground. Return currents from the LSG driver output return through the PGND
pin. Connect to AGND and PowerPAD package.
11
12
PGND
VBIAS
Internal 8-V bias voltage. A 1-µF ceramic bypass capacitance is required on the VBIAS pin.
Gate drive for optional low-side MOSFET. Connect gate of n-channel MOSFET for a higher efficiency
synchronous buck converter configuration. Otherwise, leave open and connect Schottky diode from ground
to PH pins.
13
LSG
14, 15
16
PH
Phase node. Connect to external L-C filter.
BOOT
Bootstrap capacitor for high-side gate driver. Connect a 0.1-µF ceramic capacitor from BOOT to PH pins.
PGND and AGND pins must be connected to the exposed pad for proper operation. See Figure 23 for an
example PCB layout.
PowerPAD
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
FUNCTIONAL BLOCK DIAGRAM
BOOT
VIN
PH
320 kΩ
UVLO
Hiccup
Current Limit
UVLO
(1)
125 kΩ
1.2V
SYNC
RT
2x Oscillator
PWM Ramp
Bias + Drive
Regulator
VBIAS
(FeedFoward)
Z3
S
R
Q
Adaptive Deadtime
and
Control Logic
PWM
Comparator
VBIAS
COMP
Z1
Z4
VSENSE
LSG
Z2
Error
Amplifier
Z5
VBIAS2
Thermal
Shutdown
Reference
System
PWRGD
UVLO
Rising
Edge
Delay
VSENSE
97% Ref
5 µA
UVLO
ENA
Hiccup
Hiccup
Timer
TPS5435x
POWERPAD
VBIAS
PGND
AGND
( )
1
75 kΩ for the TPS54357
DETAILED DESCRIPTION
Undervoltage Lockout (UVLO)
The UVLO system has an internal voltage divider from VIN to AGND. The defaults for the start/stop values are
labeled VIN and are given in Table 1. The internal UVLO threshold can be overridden by placing an external
resistor divider from VIN to ground. The internal divider values are approximately 320 kΩ for the high-side
resistor and 125 kΩ for the low-side resistor. The divider ratio (and, therefore, the default start/stop values) is
quite accurate, but the absolute values of the internal resistors may vary as much as 15%. If high accuracy is
required for an externally adjusted UVLO threshold, select lower-value external resistors to set the UVLO
threshold. Using a 1-kΩ resistor for the low-side resistor (R2 see Figure 1) is recommended. Under no
circumstances should the UVLO pin be connected directly to VIN.
Table 1. Start/Stop Voltage Threshold
START VOLTAGE THRESHOLD
STOP VOLTAGE THRESHOLD
TPS54352-6
TPS54357
4.49
6.65
1.24
3.69
5.45
1.02
VIN (default)
UVLO
The equations for selecting the UVLO resistors are:
VIN(start) 1 kW
R1 +
* 1 kW
1.24 V
(1)
(2)
(R1 ) 1 kW) 1.02 V
1 kW
VIN(stop) +
8
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
Input
Voltage
Supply
320 kΩ
125 kΩ
R1
R2
(1)
1 kΩ
( )
1
75 kΩ for the TPS54357
Figure 1. Circuit Using External UVLO Function
For applications that require an UVLO threshold greater than 4.49 V (6.6 V for TPS54357), external resistors
may be implemented (see Figure 1) to adjust the start-voltage threshold. For example, an application needing a
UVLO start voltage of approximately 7.8 V using equation 1, R1 is calculated to the nearest standard resistor
value of 5.36 kΩ. Using equation 2, the input voltage stop threshold is calculated as 6.48 V.
Enable (ENA) and Internal Slow Start
The TPS5435x has an internal digital slow start that ramps the reference voltage to its final value in 1150
switching cycles. The internal slow-start time (10% to 90%) is approximated by the following expression:
1.15k
ƒ (kHz) n
T
(ms) +
SS_INTERNAL
s
Use n in Table 2.
(3)
Table 2. Slow-Start Characteristics
DEVICE
n
TPS54352
TPS54353
TPS54354
TPS54355
TPS54356
TPS54357
1.485
1.2
1
1.084
0.818
0.900
Once the TPS5435x device is in normal regulation, the ENA pin is high. If ENA is pulled below the stop threshold
of 0.5 V, switching stops and the internal slow start resets. If an application requires the TPS5435x to be
disabled, use open-drain or open-collector output logic to interface to ENA (see Figure 2). ENA has an internal
pullup current source. Do not use external pullup resistors.
5 µA
R
Disabled
Enabled
SS
C
SS
Figure 2. Interfacing to the ENA Pin
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
Extending Slow-Start Time
In applications that use large values of output capacitance, there may be a need to extend the slow-start time to
prevent the startup current from tripping the current limit. The current-limit circuit is designed to disable the
high-side MOSFET and reset the internal voltage reference for a short amount of time when the high-side
MOSFET current exceeds the current-limit threshold. If the output capacitance and load current cause the startup
current to exceed the current-limit threshold, the power-supply output will not reach the desired output voltage.
To extend the slow-start time and to reduce the startup current, an external resistor and capacitor can be added
to the ENA pin. The slow-start capacitance is calculated using the following equation:
CSS (µF) = 5.55 10−3 n Tss (ms)
Use n in Table 2.
(4)
The RSS resistor must be 2 kΩ and the slow-start capacitor must be less than 0.47 µF.
Switching Frequency (RT)
The TPS5435x has an internal oscillator that operates at twice the PWM switching frequency. The internal
oscillator frequency is controlled by the RT pin. Grounding RT sets the PWM switching frequency to a default
frequency of 250 kHz. Floating RT sets the PWM switching frequency to 500 kHz.
Connecting a resistor from RT to AGND sets the frequency according to the following equation (also see
Figure 30).
46000
ƒ (kHz) * 35.9
RT (kW) +
s
(5)
RT controls the SYNC pin functions. If RT is floating or grounded, SYNC is an output. If the switching frequency
has been programmed using a resistor from RT to AGND, SYNC functions as an input.
The internal voltage-ramp charging current increases linearly with the set frequency and keeps the feed-forward
modulator constant (Km = 8), regardless of the frequency set point.
Table 3.
SWITCHING FREQUENCY
250 kHz, internally set
500 kHz, internally set
SYNC PIN
RT PIN
AGND
Float
Generates SYNC output signal
Generates SYNC output signal
Terminate to quiet ground
Externally set from 250 kHz to 700 kHz
R = 215 kΩ to 69 kΩ
with 10-kΩ resistor
Set RT resistor equal to 90% to 110% of external
synchronization frequency. When using a dual setup (see
Figure 27 for example), if the master 35x device RT pin is
left floating, use a 110-kΩ resistor to tie the slave RT pin
to ground. Conversely, if the master 35x device RT pin is
grounded, use a 237-kΩ resistor to tie the slave RT pin to
ground.
Externally synchronized frequency
Synchronization signal
180° Out-of-Phase Synchronization (SYNC)
The SYNC pin is configurable as an input or as an output, as noted in the previous section. When operating as
an input, SYNC is a falling-edge-triggered signal (see Figure 3, Figure 4, and Figure 19). When operating as an
output, the signal's falling edge is approximately 180° out of phase with the rising edge of the PH pins. Thus, two
TPS5435x devices operating in a system can share an input capacitor and draw ripple current at twice the
frequency of a single unit.
When operating the two TPS5435x devices 180° out of phase, the total RMS input current is reduced, thus,
reducing the amount of input capacitance needed and increasing efficiency.
When synchronizing a TPS5435x to an external signal, the timing resistor on the RT pin must be set so that the
oscillator is programmed to run at 90% to 110% of the synchronization frequency.
10
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
V
I(SYNC)
V
O(PH)
Figure 3. SYNC Input Waveform
Internal Oscillator
V
O(PH)
V
O(SYNC)
Figure 4. SYNC Output Waveform
Power Good (PWRGD)
The VSENSE pin is compared to an internal reference signal if the VSENSE is greater than 97% and no other
faults are present. The PWRGD pin presents a high impedance. A low on PWRGD indicates a fault. PWRGD
has been designed to provide a weak pulldown and indicates a fault even when the device is unpowered. If the
TPS5435x has power and has any fault flag set, the TPS5435x indicates the power is not good by driving the
PWRGD pin low. The following events, singly or in combination, indicate power is not good:
•
•
•
•
•
•
•
VSENSE pin out of bounds
Overcurrent
Thermal shutdown
UVLO undervoltage
Input voltage not present (weak pulldown)
Slow starting
VBIAS voltage is low.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
Once the PWRGD pin presents a high impedance (i.e., power is good), a VSENSE pin out-of-bounds condition
forces PWRGD low (i.e., power is bad) after a time delay. This time delay is a function of the switching frequency
and is calculated using equation 6:
1000
T
+
ms
delay
ƒ (kHz)
s
(6)
Bias Voltage (VBIAS)
The VBIAS regulator provides a stable supply for the internal analog circuits and the low-side gate driver. Up to 1
mA of current can be drawn for use in an external application circuit. The VBIAS pin must have a bypass
capacitor value of 1 µF. X7R- or X5R-grade dielectric ceramic capacitors are recommended because of their
stable characteristics over temperature.
Bootstrap Voltage (BOOT)
The BOOT capacitor obtains its charge cycle by cycle from the VBIAS capacitor. A capacitor from the BOOT pin
to the PH pins is required for operation. The bootstrap connection for the high-side driver must have a bypass
capacitor of 0.1 µF.
Error Amplifier
The VSENSE pin is the error amplifier inverting input. The error amplifier is a true voltage amplifier, with 1.5 mA
of drive capability with a minimum of 60 dB of open-loop voltage gain and a unity-gain bandwidth of 2 MHz.
Voltage Reference
The voltage-reference system produces
a precision reference signal by scaling the output of a
temperature-stable bandgap circuit. During production testing, the bandgap and scaling circuits are trimmed to
produce 0.891 V at the output of the error amplifier, with the amplifier connected as a voltage follower. The trim
procedure improves the regulation, since it cancels offset errors in the scaling and error-amplifier circuits.
PWM Control and Feed Forward
Signals from the error-amplifier output, oscillator, and current-limit circuit are processed by the PWM control
logic. Referring to the internal block diagram, the control logic includes the PWM comparator, PWM latch, and
the adaptive dead-time control logic. During steady-state operation below the current-limit threshold, the PWM
comparator output and oscillator pulse train alternately reset and set the PWM latch.
Once the PWM latch is reset, the low-side driver and integrated pulldown MOSFET remain on for a minimum
duration set by the oscillator pulse width. During this period, the PWM ramp discharges rapidly to the valley
voltage. When the ramp begins to charge back up, the low-side driver turns off and the high-side FET turns on.
The peak PWM ramp voltage varies inversely with input voltage to maintain a constant modulator and
power-stage gain of 8 V.
As the PWM ramp voltage exceeds the error-amplifier output voltage, the PWM comparator resets the latch, thus
turning off the high-side FET and turning on the low-side FET. The low-side driver remains on until the next
oscillator pulse discharges the PWM ramp.
During transient conditions, the error-amplifier output can be below the PWM ramp valley voltage or above the
PWM peak voltage. If the error amplifier is high, the PWM latch is never reset and the high-side FET remains on
until the oscillator pulse signals the control logic to turn the high-side FET off and the internal low-side FET and
driver on. The device operates at its maximum duty cycle until the output voltage rises to the regulation set point,
setting VSENSE to approximately the same voltage as the internal voltage reference. If the error-amplifier output
is low, the PWM latch is reset continually and the high-side FET does not turn on. The internal low-side FET and
low-side driver remain on until the VSENSE voltage decreases to a range that allows the PWM comparator to
change states. The TPS5435x is capable of sinking current through the external low-side FET until the output
voltage reaches the regulation set point.
The minimum on time is designed to be 180 ns. During the internal slow-start interval, the internal reference
ramps from 0 V to 0.891 V. During the initial slow-start interval, the internal reference voltage is very small,
resulting in skipped pulses because the minimum on time causes the actual output voltage to be slightly greater
than the preset output voltage, until the internal reference ramps up.
12
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
Deadtime Control
Adaptive dead-time control prevents shoot-through current from flowing in the integrated high-side MOSFET and
the external low-side MOSFET during the switching transitions by actively controlling the turn-on times of the
drivers. The high-side driver does not turn on until the voltage at the gate of the low-side MOSFET is below 1 V.
The low-side driver does not turn on until the voltage at the gate of the high-side MOSFET is below 1 V.
Low-Side Gate Driver (LSG)
LSG is the output of the low-side gate driver. The 100-mA MOSFET driver is capable of providing gate drive for
most popular MOSFETs suitable for this application. Use the SWIFT Designer Software Tool to find the most
appropriate MOSFET for the application. Connect the LSG pin directly to the gate of the low-side MOSFET. Do
not use a gate resistor, as the resulting turn-on time may be too slow.
Integrated Pulldown MOSFET
The TPS5435x has a diode-MOSFET pair from PH to PGND. The integrated MOSFET is designed for light-load
continuous-conduction-mode operation when only an external Schottky diode is used. The combination of
devices keeps the inductor current continuous under conditions where the load current drops below the inductor's
critical current. Care should be taken in the selection of inductor in applications using only a low-side Schottky
diode. Since the inductor ripple current flows through the integrated low-side MOSFET at light loads, the
inductance value should be selected to limit the peak current to less than 0.3 A during the high-side FET turn-off
time. The minimum value of inductance is calculated using the following equation:
VO
VO ǒ1 *
Ǔ
VI
L(H) +
ƒ 0.6
s
(7)
Thermal Shutdown
The device uses the thermal shutdown to turn off the MOSFET drivers and controller if the junction temperature
exceeds 165°C. The device is restarted automatically when the junction temperature decreases to 7°C below the
thermal shutdown trip point and starts up under control of the slow-start circuit.
Overcurrent Protection
Overcurrent protection is implemented by sensing the drain-to-source voltage across the high-side MOSFET and
compared to a voltage level that represents the overcurrent threshold limit. If the drain-to-source voltage exceeds
the overcurrent threshold limit for more than 100 ns, the ENA pin is pulled low, the high-side MOSFET is
disabled, and the internal digital slow-start is reset to 0 V. ENA is held low for approximately the time that is
calculated by the following equation:
2250
T
(ms) +
HICCUP
ƒ (kHz)
s
(8)
Once the hiccup time is complete, ENA is released and the converter initiates the internal slow start.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS
Conditions are VI = 12 V, VO = 3.3 V, fs = 500 kHz, IO = 3 A, TA = 25°C (unless otherwise noted).
MEASURED LOOP RESPONSE
LOAD REGULATION
LINE REGULATION
0.3
0.2
0.1
60
50
40
30
20
10
180
150
120
90
0.1
0.08
0.06
0.04
0.02
Phase
V = 12 V
I
I
= 3 A
O
I
= 1.5 A
60
O
V = 6 V
I
30
Gain
0
−0.1
−0.2
−0.3
0
−10
−20
−30
0
0
−30
−60
−90
−0.02
V = 18 V
I
I
= 0 A
O
−0.04
−0.06
−40
−50
−60
−120
See Figure 25
See Figure 25
See Figure 25
−0.08
−0.1
−150
−180
10 12 14 16 18 20 22
0
0.5
1
1.5
2
2.5
3
3.5
4
6
8
100
1 k
10 k
100 k
1 M
I
− Output Current − A
O
V − Input Voltage − V
I
f − Frequency − Hz
Figure 1
Figure 5.
Figure 6.
Figure 7.
EFFICIENCY
vs
OUTPUT CURRENT
INPUT RIPPLE VOLTAGE
OUTPUT RIPPLE VOLTAGE
V
= 100 mV/div (ac coupled)
I(RIPPLE)
100
V
= 10 mV/div (ac coupled)
O(RIPPLE)
V = 6 V
I
95
90
85
80
75
70
65
60
V = 12 V
I
V
= 5 V/div
V
= 5 V/div
(PH)
(PH)
V = 18 V
I
See Figure 25
See Figure 25
55
50
Time − 1 µs/div
Time − 1 µs/div
See Figure 25
1
0
2
3
4
I
− Output Current − A
O
Figure 8.
Figure 9.
Figure 10.
GATE DRIVE VOLTAGE
LOAD TRANSIENT RESPONSE
POWER UP
V
= 50 mV/div (ac coupled)
O
V
= 5 V/div
(LSG)
V = 5 V/div
I
I
= 1 A/div
(PH)
V
= 5 V/div
V
= 2 V/div
O
(PH)
V
= 2 V/div
(PWRGD)
See Figure 25
See Figure 25
Time − 2 ms/div
See Figure 25
Time − 1 µs/div
Time − 200 µs/div
Figure 11.
Figure 12.
Figure 13.
14
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
TYPICAL CHARACTERISTICS (continued)
Conditions are VI = 12 V, VO = 3.3 V, fs = 500 kHz, IO = 3 A, TA = 25°C (unless otherwise noted).
POWER DOWN
EFFICIENCY
vs
CONTINUOUS CONDUCTION MODE
V
= 5 V/div
(PH)
OUTPUT CURRENT
100
95
90
85
80
75
70
65
60
55
50
V = 6 V
I
V
= 5 V/div
I
V = 12 V
I
I
= 200 mA/div
(L1)
V
= 2 V/div
O
V = 18 V
I
V
= 2 V/div
(PWRGD)
See Figure 26
See Figure 25
Time − 2 ms/div
Time − 1 µs/div
See Figure 26
1
0
2
3
4
I
− Output Current − A
O
Figure 14.
Figure 15.
Figure 16.
LIGHT LOAD CONDUCTION
SEQUENCING WAVEFORMS
INPUT RIPPLE CANCELLATION
V
= 10 V/div
V
= 5 V/div
(PH1)
(PH)
V = 10 V/div
I
V
= 2 V/div
V
= 10 V/div
O1(3.3)
(PH2)
I
= 200 mA/div
(L1)
V = 50 mV/div (ac coupled)
I
V
= 2 V/div
= 2 V/div
(PWRGD1)
V
O2 (1.8)
See Figure 27
See Figure 26
See Figure 27
Time − 1 µs/div
Time − 2 ms/div
Time − 1 µs/div
Figure 17.
Figure 18.
Figure 19.
MEASURED LOOP RESPONSE
MEASURED LOOP RESPONSE
MEASURED LOOP RESPONSE
100-mF POSCAP
2 y 180-mF SP CAPACITORS
330-mF OSCON
60
50
40
30
20
60
50
40
30
20
10
0
60
50
40
180
150
180
150
180
150
120
90
Phase
Phase
Phase
120
90
120
90
60
30
0
30
20
10
0
60
60
Gain
Gain
Gain
30
30
10
0
0
0
−30
−60
−90
−120
−150
−10
−10
−30
−10
−20
−30
−30
−60
−90
−120
−20
−30
−60
−20
−30
−40
−50
−60
−90
−40
−50
−60
−120
−150
−180
−40
−50
−60
See Figure 30
See Figure 28
See Figure 29
−150
−180
−180
1 M
100
1 k
10 k
100 k
100
1 k
10 k
100 k
1 M
100
1 k
10 k
100 k
1 M
f − Frequency − Hz
f − Frequency − Hz
f − Frequency − Hz
Figure 20.
Figure 21.
Figure 22.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
LAYOUT INFORMATION
Figure 23. TPS5435x PCB Layout
PCB Layout
The VIN pins should be connected together on the printed circuit board (PCB) and bypassed with a low-ESR
ceramic bypass capacitor. Care should be taken to minimize the loop area formed by the bypass capacitor
connections, the VIN pins, and the TPS5435x ground pins. The minimum recommended bypass capacitance is
10-µF ceramic with a X5R or X7R dielectric, and the optimum placement is closest to the VIN pins and the
AGND and PGND pins. See Figure 23 for an example of a board layout. The AGND and PGND pins should be
tied to the PCB ground plane at the pins of the IC. The source of the low-side MOSFET and the anode of the
Schottky diode should be connected directly to the PCB ground plane. The PH pins should be tied together and
routed to the drain of the low-side MOSFET or to the cathode of the external Schottky diode. Since the PH
connection is the switching node, the MOSFET (or diode) should be located very close to the PH pins, and the
area of the PCB conductor minimized to prevent excessive capacitive coupling. The recommended conductor
width from pins 14 and 15 is 0.050 in to 0.075 in of 1-oz copper. The length of the copper land pattern should be
no more than 0.2 in.
For operation at full-rated load, the analog ground plane must provide adequate heat dissipating area. A 3-in ×
3-in plane of copper is recommended, though not mandatory, dependent on ambient temperature and airflow.
Most applications have larger areas of internal ground plane available, and the PowerPAD package should be
connected to the largest area available. Additional areas on the bottom or top layers also help dissipate heat,
and any area available should be used when 3 A or greater operation is desired. Connection from the exposed
area of the PowerPAD package to the analog ground-plane layer should be made using 0.013-in diameter vias to
avoid solder wicking through the vias. Four vias should be in the PowerPAD area, with four additional vias
outside the pad area and underneath the package. Additional vias beyond those recommended to enhance
thermal performance should be included in areas not under the device package.
16
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
j0.0130
Minimum recommended thermal vias:
4 y 0.013 diameter inside PowerPAD area and
8 PL
4 y 0.013 diameter under device as shown.
Additional 0.018 diameter vias may be used if
top-side analog ground area is extended.
Minimum recommended exposed copper
area for PowerPAD package . 5-mil
stencils may require 10-% larger area.
0.0150
0.06
0.0371
0.0400
0.1970
0.1942
0.0570
0.0400
0.0400
0.0256
Connect pin 10 AGND
0.1700
0.1340
Minimum recommended
top-side analog ground area.
and pin 11 PGND to
analog ground plane in
this area for optimum
performance.
0.0690
0.0400
Figure 24. Thermal Considerations for PowerPAD™ Layout
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
APPLICATION INFORMATION
Figure 25 shows the schematic for a typical TPS54356 application. The TPS54356 can provide up to 3-A output
current at a nominal output voltage of 3.3 V. For proper thermal performance, the exposed PowerPAD package
underneath the device must be soldered down to the printed circuit board.
+
+
Figure 25. Application Circuit, 12 V to 3.3 V
Design Procedure
The following design procedure can be used to select component values for the TPS54356. Alternately, the
SWIFT Designer Software may be used to generate a complete design. The SWIFT Designer Software uses an
iterative design procedure and accesses a comprehensive database of components when generating a design.
This section presents a simplified discussion of the design process.
To begin the design process, a few parameters must be decided upon. The designer needs to know the
following:
•
•
•
•
•
•
Input voltage range
Output voltage
Input ripple voltage
Output ripple voltage
Output current rating
Operating frequency
For this design example, use the following as the input parameters:
DESIGN PARAMETER
Input voltage range
Output voltage
EXAMPLE VALUE
6 V to 18 V
3.3 V
Input ripple voltage
Output ripple voltage
Output current rating
Operating frequency
300 mV
10 mV
3 A
500 kHz
Switching Frequency
The switching frequency is set using the RT pin. Grounding RT sets the PWM switching frequency to a default
frequency of 250 kHz. Floating RT sets the PWM switching frequency to 500 kHz. By connecting a resistor from
RT to AGND, any frequency in the range of 250 kHz to 700 kHz can be set. Use equation 9 to determine the
proper value of RT.
46000
ƒ (kHz) * 35.9
RT (kW) +
s
(9)
In this example circuit, RT is not connected and the switching frequency is set at 500 kHz.
18
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
Input Capacitors
The TPS54356 requires an input decoupling capacitor and, depending on the application, a bulk input capacitor.
The minimum value for the decoupling capacitor, C9, is 10 µF. A high-quality ceramic type X5R or X7R is
recommended. The voltage rating should be greater than the maximum input voltage. Additionally, some bulk
capacitance may be needed, especially if the TPS54356 circuit is not located within about 2 in from the input
voltage source. The value for this capacitor is not critical, but it also should be rated to handle the maximum
input voltage including ripple voltage and should filter the output so that input ripple voltage is acceptable.
This input ripple voltage can be approximated by equation 10:
IOUT(MAX) 0.25
DVIN
+
) (IOUT(MAX) ESR(MAX))
CBULK ƒsw
(10)
Where:
IOUT(MAX) = Maximum load current
ƒSW= Switching frequency
CBULK = Bulk capacitor value
and ESRMAX = Maximum series resistance of the bulk capacitor
The maximum RMS ripple current also needs to be checked. For worst-case conditions, this can be
approximated by equation 11:
I
OUT(MAX)
I
+
CIN
2
(11)
In this case, the input ripple voltage is 140 mV and the RMS ripple current is 1.5 A. The maximum voltage across
the input capacitors is VIN max plus delta VIN/2. The chosen bulk and bypass capacitors are each rated for 25 V
and the combined ripple current capacity is greater than 3 A, both providing ample margin. It is very important
that the maximum ratings for voltage and current are not exceeded under any circumstance.
Output Filter Components
Inductor Selection
To calculate the minimum value of the output inductor, use equation 12:
ǒVIN(MAX) OUTǓ
V
* V
OUT
L
+
(MIN)
V
K
I
ƒ
sw
IN(MAX)
IND
OUT
(12)
KIND is a coefficient that represents the amount of inductor ripple current relative to the maximum output current.
For designs using low ESR output capacitors such as ceramics, use KIND = 0.3. When using higher ESR output
capacitors, KIND = 0.2 yields better results.
For this design example, use KIND = 0.1 to keep the inductor ripple current small. The minimum inductor value is
calculated to be 17.96 µH. The next-highest standard value is 22 µH, which is used in this design.
For the output filter inductor, it is important that the RMS current and saturation current ratings not be exceeded.
The RMS inductor current can be derived from equation 13:
2
ǒ
Ǔ
VOUT VIN(MAX) * VOUT
1
12
IL(RMS)
+
I2
)
ǒ
Ǔ
Ǹ
OUT(MAX)
VIN(MAX) LOUT ƒsw 0.8
(13)
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
and the peak inductor current can be determined using equation 14:
ǒ
Ǔ
VOUT VIN(MAX) * VOUT
IL(PK) + IOUT(MAX)
)
1.6 VIN(MAX) LOUT ƒsw
(14)
For this design, the RMS inductor current is 3.007 A and the peak inductor current is 3.15 A. The chosen
inductor is a Coiltronics DR127-220 22 µH. It has a saturation current rating of 7.57 A and a RMS current rating
of 4 A, easily meeting these requirements. A lesser-rated inductor could be used if less margin is desired. In
general, inductor values for use with the TPS54356 are in the range of 6.8 µH to 47 µH.
Capacitor Requirements
The important design factors for the output capacitor are dc voltage rating, ripple current rating, and equivalent
series resistance (ESR). The dc voltage and ripple current ratings cannot be exceeded. The ESR is important
because, along with the inductor current, it determines the amount of output ripple voltage. The actual value of
the output capacitor is not critical, but some practical limits do exist.
Consider the relationship between the desired closed-loop crossover frequency of the design and LC corner
frequency of the output filter. In general, it is desirable to keep the closed-loop crossover frequency at less than
one-fifth of the switching frequency. With high switching frequencies such as the 500-kHz frequency of this
design, internal circuit limitations of the TPS54356 limit the practical maximum crossover frequency to about 70
kHz. Additionally, the capacitor type and value must be chosen to work with the internal compensation network of
the TPS5435x family of dc/dc converters. To allow for adequate phase gain in the compensation network, the LC
corner frequency should be approximately one decade or so below the closed-loop crossover frequency. This
limits the minimum capacitor value for the output filter to:
1
K
2
C
+
(2pƒ )
OUT(MIN)
L
CO
OUT
(15)
Where K is the frequency multiplier for the spread between fLC and fCO. K should be between 5 and 15, typically
10, for one decade difference. For a desired crossover of 20 kHz and a 22-µH inductor, the minimum value for
the output capacitor is 288 µF. The selected output capacitor must be rated for a voltage greater than the desired
output voltage, plus one-half the ripple voltage. Any derating amount also must be included. The maximum RMS
ripple current in the output capacitor is given by equation 16:
ǒ
Ǔ
V
VIN(MAX) * VOUT
ȡ
ȣ
OUT
1
ICOUT(RMS)
+
ȧ
ȧ
Ǹ
VIN(MAX) LOUT ƒsw
12
(16)
The calculated RMS ripple current is 156 mA in the output capacitors.
Choosing Capacitor Value
For this design example, a relatively large aluminum electrolytic capacitor is combined with a smaller-value
ceramic capacitor. This combination provides a stable high-performance design at a relatively low cost. Also, by
carefully choosing the capacitor values and ESRs, the design can be tailored to complement the internal
compensation poles and zeros of the TPS54356.
These preconfigured poles and zeroes, internal to the TPS54356, limit the range of output filter configurations. A
variety of capacitor values and types of dielectric are supported. There are a number of different ways to
calculate the output filter capacitor value and ESR to work with the internal compensation network. This
procedure outlines a relatively simple procedure that produces good results with an output filter consisting of a
high-ESR dielectric capacitor in parallel with a low-ESR ceramic capacitor. SWIFT Designer Software is used for
designs with unusually high closed-loop crossover frequencies, low value, low-ESR output capacitors such as
ceramics, or if the designer is unsure about the design procedure.
20
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
The TPS54356 contains a compensation network with the following nominal characteristics:
ƒINT = 1.7 kHz
ƒZ1 = 2.5 kHz
ƒZ2 = 4.8 kHz
ƒP1 = 95 kHz
ƒP2 = 125 kHz
For a stable design, the closed-loop crossover frequency should be set less than one-fifth of the switching
frequency, and the phase margin at crossover must be greater than 45 degrees. The general procedure outlined
here produces results consistent with these requirements, without going into great detail about the theory of loop
compensation.
In this case, the output filter LC corner frequency should be selected to be near the first compensation zero
frequency, as described by equation 17:
1
ƒ
+
^ ƒ
LC
Z1
2p ǸL
C2
OUT
(17)
Placement of the LC corner frequency at fZ1 is not critical; it only needs to be close. For the design example,
fLC = 2 kHz.
Solving for C2 using equation 18:
1
C2 ^
4p2ƒ2
L
Z1 OUT
(18)
The desired value for C2 is calculated as 184 µF. A close standard value of 330 µF is chosen, with a resulting
LC corner frequency of 1.9 kHz. As shown, this value is not critical as long as it results in a corner frequency in
the vicinity of fZ1.
Next, when using a large ceramic capacitor in parallel with a high-ESR electrolytic capacitor, there is a pole in
the output filter that should be at fZ2, as shown in equation 19:
1
ƒ
+
+ ƒ
P(ESR)
Z2
2pR
C5
(C2ESR)
(19)
Now, the actual C2 capacitor must be selected based on the ESR and the value of capacitor C5, so that the
above equation is satisfied. In this example, the R(C2ESR)C5 product should be 3.18 × 10–5. From the available
capacitors, by choosing a Panasonic EEVFKOJ331XP aluminum electrolytic capacitor with a nominal ESR of
0.34 Ω yields a calculated value for C5 of 98 µF. The closest standard value is 100 µF. As the actual ESR of the
capacitor can vary by a large amount, this value also is not critical.
The closed-loop crossover frequency should be greater than fLC and less than one-fifth of the switching
frequency. Also, the crossover frequency should not exceed 70 kHz, as the error amplifier may not provide the
desired gain. As stated previously, closed loop-crossover frequencies between 5 and 15 times fLC work well. For
this design, the crossover frequency can be estimated by:
*3
ƒ
+ 1.125 10 ƒ
ƒ
CO
P(ESR)
LC
(20)
This simplified equation is valid for this design because the output filter capacitors are mixed technology.
Compare this result to the actual measured loop response plot of Figure 5. The measured closed-loop crossover
frequency of 19.95 kHz differs from the calculated value because the actual output filter capacitor component
parameters differed slightly from the specified data-sheet values.
Capacitor ESR and Output Ripple
The amount of output ripple voltage, as specified in the initial design parameters, is determined by the maximum
ESR of the output capacitor and the input ripple current. The output ripple voltage is the inductor ripple current
times the ESR of the output filter, so the maximum specified ESR as listed in the capacitor data sheet is given by
equation 21:
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
VIN(MAX) LOUT ƒsw 0.8
ESR(MAX)
+
DV
p*p(MAX)
ǒ
Ǔ
ǒ
Ǔ
VOUT VIN(MAX) * VOUT
(21)
and the maximum ESR required is 33 mΩ. In this design, the aluminum electrolytic capacitor has an ESR of
0.340 mΩ, but it is in parallel with an ultra-low ESR ceramic capacitor of 2 mΩ maximum. The measured output
ripple voltage for this design is approximately 4 mVp-p, as shown in Figure 10.
Bias AND Bootstrap Capacitors
Every TPS54356 design requires a bootstrap capacitor, C3, and a bias capacitor, C4. The bootstrap capacitor
must be 0.1 µF. The bootstrap capacitor is located between the PH pins and BOOT pin. The bias capacitor is
connected between the VBIAS pin and AGND. The value should be 1 µF. Both capacitors should be high-quality
ceramic types with X7R or X5R grade dielectric for temperature stability. They should be placed as close to the
device connection pins as possible.
Low-Side FET
The TPS54356 is designed to operate using an external low-side FET, and the LSG pin provides the gate drive
output. Connect the drain to the PH pin, the source to PGND, and the gate to LSG. The TPS54356 gate drive
circuitry is designed to accommodate most common n-channel FETs that are suitable for this application. The
SWIFT Designer Software can be used to calculate all the design parameters for low-side FET selection. There
are some simplified guidelines that can be applied that produce an acceptable solution in most designs.
The selected FET must meet the absolute maximum ratings for the application:
•
Drain-source voltage (VDSS) must be higher than the maximum voltage at the PH pin, which is
VINMAX + 0.5 V.
•
•
•
Gate-source voltage (VGSS) must be greater than 8 V.
Drain current (ld) must be greater than 1.1 × IOUTMAX
.
Drain-source on resistance (RDSON) should be as small as possible; less than 30 mΩ is desirable. Lower
values for RDSON result in designs with higher efficiencies. It is important to note that the low-side FET on
time typically is longer than the high-side FET on time, so attention paid to low-side FET parameters can
make a marked improvement in overall efficiency.
•
•
Total gate charge (Qg) must be less than 50 nC. Again, lower Qg characteristics result in higher efficiencies.
Additionally, check that the device chosen is capable of dissipating the power losses.
For this design, a Fairchild FDR6674A 30-V n-channel MOSFET is used as the low-side FET. This particular FET
is designed specifically to be used as a low-side synchronous rectifier.
Power Good
The TPS54356 is provided with a power-good (PWRGD) output pin. This output is an open-drain output and is
intended to be pulled up to a 3.3-V or 5-V logic supply. A 10-kΩ pullup resistor works well in this application. The
absolute maximum voltage is 6 V, so care must be taken not to connect this pullup resistor to VIN if the
maximum input voltage exceeds 6 V.
Snubber Circuit
R10 and C11 of the application schematic in Figure 25 comprise a snubber circuit. The snubber is included to
reduce overshoot and ringing on the phase node when the internal high-side FET turns on. Since the frequency
and amplitude of the ringing depends to a large degree on parasitic effects, it is best to choose these component
values, based on actual measurements of any design layout. See literature number SLUP100 for more detailed
information on snubber design.
Figure 26 shows an application where a clamp diode is used in place of the low-side FET. The TPS54352-7
incorporates an integrated pulldown FET so that the circuit remains operating in continuous mode during light
load operation. A 3-A 40-V Schottky diode, such as the Motorola MBRS340T3 or equivalent, is recommended.
See Figure 15, Figure 16, and Figure 17 for efficiency data and switching waveforms for this circuit.
22
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
+
+
Figure 26. Power Supply With Schottky Diode
Figure 27 is an example of power-supply sequencing using a TPS54356 (U1) to generate an output of 3.3 V, and
a TPS54354 (U2) to generate a 1.8-V output. These output voltages are typical I/O and core voltages for
microprocessors and FPGAs. In the circuit, the 3.3-V supply is designed to power up first.
+
+
Pull up to
3.3 V or 5 V
+
+
Figure 27. Power Supply With Sequencing
The PWRGD pin of U1 is tied to the ENA pin of U2 so that the 1.8-V supply starts to ramp up after the 3.3-V
supply is within regulation. Figure 18 shows these start-up sequence waveforms.
Since the RT pin of U1 is floating, the SYNC pin is an output. This synchronization signal is fed the SYNC pin of
U2. RT of U2 has a 110-kΩ resistor to ground, and SYNC for this device acts as an input. The 1.8-V supply
operates synchronously with the 3.3-V supply, and their switching node rising edges are approximately 180
degrees out of phase, allowing for a reduction in the input voltage ripple. See Figure 19 for this waveform.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
Alternate Output Filter Designs
The previous design procedure example demonstrated a technique to design a 3.3-V power supply using both
aluminum electrolytic and ceramic output filter capacitors. Other types of output filter capacitors are supported by
the TPS5435x family of dc/dc converters. Figure 26, Figure 27, and Figure 28 show designs using other popular
capacitor types.
In Figure 28, the TPS54356 is shown with a single 100-µF 6-V POSCAP as the output filter capacitor. C10 is a
high-frequency bypass capacitor and does not enter into the design equations. The design procedure is similar to
the previous example, except in the design of the output filter. In the previous example, the output filter LC corner
was set at the first zero in the compensation network, while the second compensation zero was used to
counteract the output filter pole caused by the interaction of the C2 capacitor ESR with C5. In this design
example, the output LC corner frequency is to be set at the second zero frequency (fZ2) of the internal
compensation network, approximately 5 kHz, while the first zero is used to provide phase boost prior to the LC
corner frequency.
+
+
Figure 28. 3.3-V Power Supply With Sanyo POSCAP Output Filter Capacitor
Inductor Selection
Using equation 12 and a KIND 0.2, the minimum inductor value required is 8.98 µH. The closest standard value,
10 µH, is selected. RMS and peak inductor currents are the same as calculated previously.
Capacitor Selection
With the inductor set at 10 µH and a desired corner frequency of 5 kHz, the output capacitor value is given by:
1
1
C2 +
+
+ 101 mF
*5
4 p2 50002 10
4p2ƒZ22 L
out
Use 100 µF as the closest standard value.
Calculating the RMS ripple current in the output capacitor using equation 16 yields 156 mA. The POSCAP
6TPC100M capacitor selected is rated for 1700 mA. See the closed-loop response curve for this design in
Figure 20.
+
+
+
Figure 29. 3.3-V Power Supply With Panasonic SP Output Filter Capacitors
24
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
In Figure 29, the TPS54356 is shown with two 180-mF 4-V special polymer dielectric output filter capacitors (C2
and C5). C10 is a high-frequency bypass capacitor and does not enter into the design equations. In the previous
example, the output LC corner frequency is to be set at the second zero frequency fZ2 of the internal
compensation network, approximately 5 kHz, while the first zero is used to provide phase boost prior to the LC
corner frequency. The special polymer electrolytic capacitors used in this design require that the closed-loop
crossover frequency be lowered due to the significantly lower ESR of this type of capacitor.
Inductor Selection
The inductor is the same 10-µH value as the previous example.
Capacitor Selection
To lower the closed-loop crossover, it is necessary to reduce the LC corner frequency below 5 kHz. Using a
target value of 2500 Hz, the output capacitor value is given by:
1
1
C2 +
+
+ 405 mF
*5
4 p2 25002 10
4p2ƒZ22 L
out
Use 2 × 180 µF = 360 µF as a combination of standard values that is close to 405 µF.
The RMS ripple current in the output capacitor is the same as before. The selected capacitors are each 3.3 A.
See the closed-loop response curve for this design in Figure 21.
In Figure 30, the TPS54356 is shown with a Sanyo OSCON output filter capacitor (C2). C10 is a high-frequency
bypass capacitor and does not enter into the design equations. This design is identical to the previous example,
except that a single OSCON capacitor of 330 µF is used for the calculated value of 405 µF. Compare the
closed-loop response for this design in Figure 22 to the closed-loop response in Figure 21. Note that there is only
a slight difference in the response and the general similarity in both the gain and phase plots. This is the
expected result for these two similar output filters.
+
+
Figure 30. 3.3-V Power Supply With Sanyo OSCON Output Filter Capacitor
Many other additional output filter designs are possible. Use the SWIFT Designer Software to generate other
designs or follow the general design procedures illustrated in this application section.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
MAXIMUM SWITCHING FREQUENCY
RT RESISTANCE
vs
VIN(UVLO) START AND STOP
vs
vs
INPUT VOLTAGE
SWITCHING FREQUENCY
FREE-AIR TEMPERATURE
800
225
200
175
150
125
100
75
6.5
6.0
5.5
5.0
4.5
4.0
3.5
TPS54357
TPS54356
700
600
500
400
300
200
100
0
Start
TPS54357
Stop
TPS54355
TPS54354
TPS54353
TPS54352
TPS54352−6
Start
Stop
I
> 0.5 A
O
50
200
5
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
300
400
500
600
700
−50 −25
0
25 50 75 100 125 150
V − Input Voltage − V
I
Switching Frequency − kHz
T
A
− Free-Air Temperature − 5C
Figure 31.
Figure 32.
Figure 33.
ENABLED SUPPLY CURRENT
DISABLED SUPPLY CURRENT
BIAS VOLTAGE
vs
vs
vs
INPUT VOLTAGE
INPUT VOLTAGE
INPUT VOLTAGE
10
9
1.3
1.2
1.1
1.0
0.9
8.0
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
T
= 25°C
= 500 kHz
J
T
J
= 25°C
T
J
= 25°C
f
S
8
7
6
5
4
3
0
5
10
15
20
25
0
5
10
15
20
25
0
5
10
15
20
25
V − Input Voltage − V
I
V − Input Voltage − V
I
V − Input Voltage − V
I
Figure 34.
Figure 35.
Figure 36.
POWER-GOOD THRESHOLD
vs
INTERNAL VOLTAGE REFERENCE
vs
CURRENT LIMIT
vs
JUNCTION TEMPERATURE
JUNCTION TEMPERATURE
INPUT VOLTAGE
98.0
97.5
97.0
96.5
96.0
0.8912
0.8910
0.8908
0.8906
0.8904
0.8902
6.0
5.5
5.0
4.5
4.0
T
J
= 25°C
VIN = 12 V
0.8900
0.8898
−50 −25
0
25 50 75 100 125 150
−50 −25
0
25 50 75 100 125 150
5.0
7.5
10.0 12.5 15.0 17.5 20.0
T
J
− Junction Temperature − 5C
T
J
− Junction Temperature − 5C
V − Input Voltage − V
I
Figure 37.
Figure 38.
Figure 39.
26
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
www.ti.com ....................................................................................................................................................... SLVS684A–JANUARY 2007–REVISED JULY 2009
ON RESISTANCE
vs
PH VOLTAGE
vs
SLOW-START CAPACITANCE
vs
JUNCTION TEMPERATURE
SINK CURRENT
TIME
2
1.75
1.50
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
150
130
110
90
V = 12 V
I
I
= 0.5 A
R
= 2 kΩ
O
SS
V = 4.5 V
I
V = 12 V
I
1.25
1
70
0.05
0
50
0
10 20 30 40 50 60 70 80
100
150
200
250
300
750
25
−50 −25
0
25 50 75 100 125 150
t − Time − ms
I
− Sink Current − mA
CC
T
J
− Junction Temperature − 5C
Figure 40.
Figure 41.
Figure 42.
POWER-GOOD DELAY
vs
SWITCHING FREQUENCY
HICCUP TIME
vs
SWITCHING FREQUENCY
INTERNAL SLOW START TIME
vs
SWITCHING FREQUENCY
5
4.5
4
10
4.5
4
TPS54354
9
8
7
6
5
3.5
3
3.5
2.5
2
3
2.5
2
1.5
1
4
3
2
1.5
1
0.5
0
250
350
450
550
650
250
350
450
550
650
750
250
350
450
550
650
750
Switching Frequency − kHz
Switching Frequency − kHz
Switching Frequency − kHz
Figure 43.
Figure 44.
Figure 45.
FREE-AIR TEMPERATURE
vs
MAXIMUM OUTPUT CURRENT
MAXIMUM OUTPUT VOLTAGE
POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
vs
INPUT VOLTAGE
6
5
4
140
120
100
80
2.5
T = 125°C
J
TPS54357
2
θ
= 42.1°C/W
JA
TPS54356
1.5
3
2
TPS54355
TPS54354
60
40
20
0
1
θ
= 191.9°C/W
JA
0.5
0
1
0
TPS54352
TPS54353
0
0.5
1
1.5
2
2.5
3
3.5
0
5
10
15
20
25
45
65
85
105
125
I
− Output Current − A
V
− Input Voltage − V
T
A
− Free-Air Temperature − °C
O
I
Figure 46.
Figure 47.
Figure 48.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
TPS54352-EP, TPS54353-EP, TPS54354-EP
TPS54355-EP, TPS54356-EP, TPS54357-EP
SLVS684A–JANUARY 2007–REVISED JULY 2009....................................................................................................................................................... www.ti.com
THERMAL PAD MECHANICAL DATA
PWP (R-PDSO-G16) ............................................................................ PowerPAD™ PLASTIC SMALL-OUTLINE
PPTD024
28
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54352-EP TPS54353-EP TPS54354-EP TPS54355-EP TPS54356-EP TPS54357-EP
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jul-2009
PACKAGING INFORMATION
Orderable Device
TPS54354MPWPREP
TPS54356MPWPREP
V62/07616-03XE
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
HTSSOP
PWP
16
16
16
16
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
V62/07616-05XE
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS54354-EP, TPS54356-EP :
Catalog: TPS54354, TPS54356
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS54354MPWPREP HTSSOP PWP
TPS54356MPWPREP HTSSOP PWP
16
16
2000
2000
330.0
330.0
12.4
12.4
6.9
6.9
5.6
5.6
1.6
1.6
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS54354MPWPREP
TPS54356MPWPREP
HTSSOP
HTSSOP
PWP
PWP
16
16
2000
2000
367.0
367.0
367.0
367.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
TPS54355PWPR
4.5V to 20V Input, 2.5V Output, 3A Synchronous Step-Down SWIFT™ Converter with Low-Side Gate Driver 16-HTSSOP -40 to 85
TI
TPS54355PWPRG4
6.5A SWITCHING REGULATOR, 600kHz SWITCHING FREQ-MAX, PDSO16, GREEN, PLASTIC, HTSSOP-16
TI
TPS54356PWPR
4.5V to 20V Input, 3.3V 3A Synchronous Step-Down SWIFT™ Converter w/ Low-Side Gate Driver 16-HTSSOP -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明