TPS61055DRCR [TI]
HIGH POWER WHITE LED DRIVER 2-MHz SYNCHRONOUS BOOST CONVERTER WITH STANDARD LOGIC INTERFACE; 大功率白光LED驱动器2 - MHz的同步升压型与标准的逻辑接口转换器型号: | TPS61055DRCR |
厂家: | TEXAS INSTRUMENTS |
描述: | HIGH POWER WHITE LED DRIVER 2-MHz SYNCHRONOUS BOOST CONVERTER WITH STANDARD LOGIC INTERFACE |
文件: | 总27页 (文件大小:1093K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CSP-12
QFN-10
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
HIGH POWER WHITE LED DRIVER
2-MHz SYNCHRONOUS BOOST CONVERTER WITH STANDARD LOGIC INTERFACE
1
FEATURES
DESCRIPTION
2
•
Four Operational Modes
–
–
–
Torch and Flash up to ILED = 700 mA
Voltage-Regulated Boost Converter: 5.0 V
Shutdown: 0.3 µA (typ)
The TPS6105x device uses
a
high-frequency
synchronous-boost topology with constant current
sink to drive single white LEDs. The device uses an
inductive fixed-frequency PWM control scheme using
small external components, minimizing input ripple
current.
•
•
•
•
•
•
•
•
•
Total Solution Circuit Area < 25 mm2
Up to 96% Efficiency
Integrated LED Turn-On Safety Timer
Zero Latency TX-Masking Input
Integrated Low Light Dimming Mode
LED Disconnect During Shutdown
Open/Shorted LED Protection
Over-Temperature Protection
The 2-MHz switching frequency allows the use of
small and low-profile 2.2-µH inductors. To optimize
overall efficiency, the device operates with only a
250-mV LED feedback voltage.
The TPS6105x device not only operates as a
regulated current source, but also as a standard
voltage-boost regulator. This additional operating
mode can be useful to supply other high-power
devices in the system, such as a hands-free audio
power amplifier, or any other component requiring a
supply voltage higher than the battery voltage.
Available in a 12-Pin NanoFree™ (CSP) and
10-Pin QFN Packaging
APPLICATIONS
•
The LED current or the desired output voltage can be
programmed via two logic signals (MODE0/1). To
simplify flash synchronization with the camera
Camera White LED Torch/Flash for Cell
Phones, Smart-Phones and PDAs
General Lighting Applications
Audio Amplifier Power Supply
•
•
module, the device offers
a
trigger pin
(FLASH_SYNC) for fast LED turn-on time.
When the TPS6105x is not in use, it can be put into
shutdown mode, reducing the input current to 0.3 µA
(typ). During shutdown, the LED pin is high
impedance to avoid leakage current through the LED.
TPS61054
4.7 mm
L
+ BATTERY
SW
SW
VOUT
INDUCTOR
2.2 mH
C1
COUT
AVIN
10 mF
L1
P
CIN
LED
SENSE
P
P
PGND
LED
MODE1
MODE0
Tx-TOFF
PGND
FLASH_SYNC
PGND
PGND
P
C2
AGND
LED ANODE
Figure 1. Typical Application
Figure 2. Typical PC-Board Layout
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
NanoFree, PowerPAD are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2008, Texas Instruments Incorporated
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE OPTIONS
SAFETY TIMER
MAXIMUM
DURATION
PART
TORCH
FLASH
PACKAGE
MARKING
CURRENT LIMIT
PACKAGE
NUMBER(1)(2)
CURRENT(3)
CURRENT(3)
TPS61054DRC
TPS61055DRC
75 mA
75 mA
700 mA
500 mA
820 ms
820 ms
1500 mA (ILIM = 01)
1000 mA (ILIM = 00)
BRX
BRY
QFN-10
QFN-10
(1) All devices are specified for operation in the commercial temperature range, –40°C to 85°C.
(2) The YZG package is available in tape and reel. Add R suffix (TPS6105xYZGR, TPS6105xDRCR) to order quantities of 3000 parts. Add
T suffix (TPS6105xYZGT, TPS6105xDRCT) to order quantities of 250 parts.
(3) For customized current settings, please contact the factory.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
TPS6105X
–0.3 to 7
–0.3 to 7
–40 to 85
150
UNIT
V
(2)
Voltage range on AVIN, VOUT, SW, LED
(2)
Voltage range on MODE0, MODE1, FLASH_SYNC, Tx-TOFF
V
(3)
TA
Operating ambient temperature range
°C
°C
°C
kV
kV
V
TJ (MAX)
Tstg
Maximum operating junction temperature
Storage temperature range
Human body model
–65 to 150
2
ESD
Charge device model
1
rating(4)
Machine model
200
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA(max)) is dependent on the maximum operating junction temperature (TJ(max)), the
maximum power dissipation of the device in the application (PD(max)), and the junction-to-ambient thermal resistance of the part/package
in the application (θJA), as given by the following equation: TA(max)= TJ(max)–(θJA X PD(max)).
(4) The human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin. The machine model is a 200-pF
capacitor discharged directly into each pin.
DISSIPATION RATINGS
POWER RATING
DERATING FACTOR
PACKAGE
THERMAL RESISTANCE(1) (2)
TA = 25°C
ABOVE(1) (2) TA = 25°C
YZG
DRC
θJA= 89°C/W
θJA= 49°C/W
θJB= 35°C/W
θJC= 3.2°C/W
1.1 W
2.4 W
12 mW/°C
20 mW/°C
(1) Measured with high-K board.
(2) Maximum power dissipation is a function of TJ(max), θJA and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max)–TA)/ θJA
.
2
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
ELECTRICAL CHARACTERISTICS
Unless otherwise noted the specification applies for VIN = 3.6 V over an operating junction temp. of –40°C ≤ TJ ≤ 125°C.
Typical values are for TA = 25°C.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
Input voltage range
2.5
6.0
2.5
V
V
VIN
Minimum input voltage for start-up
Operating quiescent current into AVIN
Shutdown current into AVIN
MODE0 = 1, MODE1 = 1, RL = 10 Ω
MODE0 = 1, MODE1 = 1
IQ
8.5
0.3
2.3
mA
µA
V
ISD
MODE0 = 0, MODE1 = 0, –40°C ≤ TJ ≤ 85°C
VIN falling
3.0
2.4
VUVLO
OUTPUT
Undervoltage lockout threshold
Current regulator mode
Voltage regulator mode
VOUT rising
VIN
5.7
5.5
VOUT
Output voltage range
V
5.0
6.0
OVP Output overvoltage protection
Output overvoltage protection hysterisis
Minimum duty cycle
6.25
V
V
OVP
D
0.15
7.5%
0.25 V ≤ VLED ≤ 2.0 V, ILED = ITORCH, TJ = 50°C
0.25 V ≤ VLED ≤ 2.0 V, ILED = IFLASH, TJ = 50°C
–15%
–12%
15%
12%
LED current accuracy(1)
LED current temperature coefficient
DC output voltage accuracy
LED sense voltage
0.08
%/°C
2.5 V ≤ VIN ≤ 0.9 VOUT, PWM operation
Boost Mode
–3%
3%
1
VLED
250
0.1
mV
LED input leakage current
VLED = VOUT = 5 V, –40°C ≤ TJ ≤ 85°C
µA
POWER SWITCH
Switch MOSFET on-resistance
80
80
rDS(on)
Ilkg(SW)
Ilim
VOUT = VGS = 3.6 V
mΩ
µA
Rectifier MOSFET on-resistance
Switch MOSFET leakage
0.1
1
1
VDS = 6.0 V, –40°C ≤ TJ ≤ 85°C
Rectifier MOSFET leakage
0.1
2.5 V ≤ VIN ≤ 6.0 V, ILIM = 00
2.5 V ≤ VIN ≤ 6.0 V, ILIM = 01 (1)
850
1275
140
1000
1500
160
20
1150
1725
Switch current limit
mA
Thermal shutdown (1)
°C
°C
Thermal shutdown hysteresis (1)
OSCILLATOR
fSW
Oscillator frequency
1.8
1.2
2.0
2.2
MHz
MODE0, MODE1, Tx-TOFF, FLASH_SYNC
V(IH)
V(IL)
High-level input voltage
V
Low-level input voltage
0.4
0.1
V
I(LKG)
Logic input leakage current
Tx-TOFF pull-down resistance
FLASH_SYNC pull-down resistance
Input connected to VIN or GND, –40°C ≤ TJ ≤ 85°C
Tx-TOFF ≤ 0.4 V
0.01
400
400
µA
kΩ
kΩ
FLASH_SYNC ≤ 0.4 V
TIMING
From shutdown into flash mode ILED = 700 mA
1.2
ms
Start-up time
From shutdown into voltage mode
MODE0 = 1, MODE1 = 1, IOUT = 0 mA
650
µs
LED current settling time(2) triggered by
rising edge on FLASH_SYNC
LED current settling time(2) triggered by
rising edge on Tx-TOFF
MODE0 = 0, MODE1 = 1,
ILED = from 75mA to 700 mA
160
20
µs
µs
MODE0 = 0, MODE1 = 1,
ILED = 700 mA to 75 mA
(1) Assured by design. Not tested in production.
(2) Settling time to ±15% of the target value
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
DEVICE INFORMATION
PIN ASSIGNMENTS
TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NO.
(QFN)
NO.
(CSP)
NAME
AVIN
VOUT
LED
5
9
6
D3
A2
D2
I
O
I
This is the input voltage pin of the device. Connect directly to the input bypass capacitor.
Boost converter output.
LED return input. This feedback pin regulates the LED current through the internal sense
resistor by regulating the voltage across it. The regulation operates with typically 250 mV
dropout voltage. Connect to the cathode of the LED.
FLASH_SYNC
10
A1
I
Flash strobe pulse synchronization input.
FLASH_SYNC = LOW (GND): The device is operating and regulating the LED current to
the torch current level (TC).
FLASH_SYNC = HIGH (VIN): The device is operating and regulating the LED current to the
flash current level (FC).
MODE0
MODE1
2
1
B3
A3
I
I
Mode selection inputs. These pins must not be left floating and must be terminated.
MODE0 = 0, MODE1 = 0: Device in shutdown mode
MODE0 = 1, MODE1 = 0: Device in torch only mode
MODE0 = 0, MODE1 = 1: Device in torch and flash mode
MODE0 = 1, MODE1 = 1: Device in constant voltage regulation mode
RF PA synchronization input.
Tx-TOFF
SW
3
8
C3
I
Tx-TOFF = LOW : The device is operating normally.
Tx-TOFF = HIGH : The device is forced into torch mode.
B1, B2
I/O Inductor connection. Drain of the internal power MOSFET. Connect to the switched side of
the inductor. SW is high impedance during shutdown.
PGND
7
4
C1, C2
D1
Power ground. Connect to AGND underneath IC.
Analog ground.
AGND
PowerPAD™
N/A
Internally connected to PGND.
4
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
FUNCTIONAL BLOCK DIAGRAM
AVIN
SW
Undervoltage
Lockout
Bias Supply
VREF = 1.22 V
Ramp
Compensation
REF
OVP
COMPARATOR
Bandgap
VOUT
S
ERROR
AMPLIFIER
Control
Logic
VREF
P
COMPARATOR
2 MHz
Oscillator
VOLTAGE
REGULATION
CURRENT
REGULATION
SENSE FB
LED
ON/OFF
Max tON Timer
MODE0
MODE1
CURRENT
CONTROL
Control
Logic
DAC
P
LED Current Regulator
FLASH_SYNC
Tx-TOFF
P
PGND
AGND
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
TIMER BLOCK DIAGRAM
LED CURRENT CONTROL
Tx-TOFF
ILED
0
0
1
1
0
1
0
1
Torch Current
Torch Current
Flash Current
Torch Current
Tx-TOFF
MODE0
MODE1
400 kW
FLASH_SYNC
400 kW
Edge Detect
LED CURRENT CONTROL
0: TORCH CURRENT LEVEL
1: FLASH CURRENT LEVEL
Start
16-bit Prescaler
t
STIM
30.5 Hz
2 MHz CLOCK
Safety Timer
LED ON/OFF CONTROL
122 Hz
Duty-Cycle Generator (6.3%)
0: LED OFF
1: TORCH CURRENT LEVEL
PARAMETER MEASUREMENT INFORMATION
TPS6105x
L
SW
SW
VOUT
2.2µH
VIN
C
OUT
10µF
AVIN
C
IN
P
P
P
LED
MODE1
MODE0
Tx-TOFF
FLASH_SYNC
P
PGND
PGND
AGND
List Of Components:
- L = Wuerth Elektronik WE-PD S Series
- CIN = COUT = TDK C1605X5R0J106MT
6
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
TYPICAL CHARACTERISTICS
Table 1. Table of Graphs
FIGURE
LED Power Efficiency
DC Input Current
vs. Input Voltage
Figure 3, Figure 4
Figure 5
vs. Input Voltage
LED Current
vs. LED Pin Headroom Voltage
vs. Output Current
vs. Load Current
Figure 6
Voltage Mode Efficiency
DC Output Voltage
Figure 7
Figure 8
DC Output Voltage
vs. Input Voltage
Figure 9
Quiescent Current
vs. Input Voltage
Figure 10
Shutdown Current
vs. Input Voltage
Figure 11
Junction Temperature
PWM Operation
vs. GPIO Voltage
Figure 12
Figure 13
Down-Mode Operation
Voltage Mode Load Transient Response
Down-Mode Line Transient Response
Duty Cycle Jitter
Figure 14
Figure 15
Figure 16
Figure 17
Input Ripple Voltage
Figure 18
Low-Light Dimming Mode Operation
Torch/Flash Sequence
TX-Masking Operation
Start-up Into Flash Operation
Figure 19
Figure 20
Figure 21, Figure 22, Figure 23
Figure 24
LED POWER EFFICIENCY
LED POWER EFFICIENCY
vs
vs
INPUT VOLTAGE
INPUT VOLTAGE
100
90
100
90
80
70
60
50
40
30
20
80
70
60
50
40
30
20
I
= 75mA
LED
I
= 500 mA
LED
I
= 700 mA
LED
I
= 1500 mA
ILIM =1500 mA
LIM
10
0
10
0
2.5
2.9
3.3
3.7
4.1
4.5
4.9
5.3 5.5
2.5
2.9
3.3
3.7
4.1
4.5
4.9
5.3 5.5
V - Input Voltage - V
I
V - Input Voltage - V
I
Figure 3.
Figure 4.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
DC INPUT CURRENT
vs
INPUT VOLTAGE
LED CURRENT
vs
LED PIN HEADROOM VOLTAGE
2500
2250
1400
I
= 1500 mA
I
= 1500 mA
LIM
LIM
1200
1000
2000
1750
1500
1250
I
= 700 mA
LED
I
= 700 mA
= 500 mA
LED
800
600
I
LED
1000
750
500
250
400
200
0
I
= 500 mA
3.3
I
LED
= 75 mA
LED
0
2.5
550 650
950
250
350 450
750 850
1050
2.9
3.7
4.1
4.5
4.9
5.3 5.5
V - Input Voltage - V
I
LED Pin Headroom Voltage - mV
Figure 5.
Figure 6.
VOLTAGE MODE EFFICIENCY
DC OUTPUT VOLTAGE
vs
OUTPUT CURRENT
vs
LOAD CURRENT
100
90
5.15
5.10
5.05
5
V
IN
= 4.2 V
V
= 5 V,
OUT
I
= 1500 mA
LIM
80
70
60
VIN = 3.6 V
VIN = 3 V
VIN = 2.5 V
V
= 4.2 V
IN
50
40
V
V
= 3.6 V
= 3 V
IN
4.95
4.90
4.85
V
IN
30
20
= 2.5 V
IN
V
I
= 5 V,
OUT
= 1500 mA
10
0
LIM
0
1
10
100
1000
10000
0.1
1
10
100
- Output Current - mA
1000
10000
I
I
- Output Current - mA
O
O
Figure 7.
Figure 8.
8
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
DC OUTPUT VOLTAGE
vs
QUIESCENT CURRENT
vs
INPUT VOLTAGE
INPUT VOLTAGE
5.60
5.50
15
14
13
12
11
I
= 0 mA
OUT
V
I
= 5.0 V,
Voltage Mode Regulation,
= 5 V
OUT
= 1500 mA
V
O
LIM
I
= 100 mA
OUT
5.40
10
9
5.30
5.20
8
7
6
5.10
5
5
4
3
2
1
0
4.90
4.80
I
= 1000 mA
OUT
2.5
2.9
3.3
3.7
4.1
4.5
4.9
5.3 5.5
2.9
3.3
3.7
4.1
5.3 5.5
2.5
4.9
4.5
V - Input Voltage - V
I
V - Input Voltage - V
I
Figure 9.
Figure 10.
SHUTDOWN CURRENT
vs
JUNCTION TEMPERATURE
vs
INPUT VOLTAGE
GPIO VOLTAGE
200
175
150
125
1.40
1.20
1
GPIO = Input,
= -100 mA
I
T
= 85°C
GPIO
A
100
75
0.80
0.60
0.40
50
T
= 25°C
A
25
GPIO
Input Buffer
0
-25
-50
T
= -40°C
4.5
A
0.20
0
100 mA
-0.50
-0.45
-0.40
-0.35
-0.30
-0.25
-0.20
2.5
2.9
3.3
3.7
4.1
4.9
5.3 5.5
V - Input Voltage - V
I
GPIO Voltage - V
Figure 11.
Figure 12.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
PWM OPERATION
DOWN-MODE OPERATION
I
LED
SW
(2V/div)
(50mA/div)
V
OUT
(500 mV/div - 3.5 V Offset)
LED Headroom Voltage
(1V/div)
I
L
(200mA/div - 0.6 A Offset)
I
L
(50mA/div)
V = 4.2 V,
I
VI = 3.6 V, VO = 5 V,
V
I
= 75 mA
OUT
(50mV/div - 5 V Offset)
IO = 500 mA, ILIM = 1500 mA
LED
t - Time = 250 ns/div
t - Time = 125 ns/div
Figure 13.
Figure 14.
VOLTAGE MODE LOAD TRANSIENT RESPONSE
DOWN-MODE LINE TRANSIENT RESPONSE
V
OUT
(200 mV/div - 4 V Offset)
V
= 3.6 V, V = 5 V,
O
= 1500 mA
I
I
LIM
V
OUT
(500 mV/div - 5 V Offset)
Battery Voltage
(200 mV/div - 4 V Offset)
I
LED
(100 mA/div - 0.3 A Offset)
I
L
(200 mA/div - 0.3 A Offset)
I
L
(500 mA/div)
V = 3.6 V to 3.9 V,
I
I
OUT
(500 mA/div)
I
= 500 mA, I
= 1500 mA
LIM
LED
t - Time = 20 ms/div
t - Time = 50 ms/div
Figure 15.
Figure 16.
10
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
DUTY CYCLE JITTER
INPUT RIPPLE VOLTAGE
Battery Voltage
TRIGGERED ON RISING EDGE
(10 mV/div - 3.3 V Offset)
SW
(1 V/div)
VOUT (20 mV/div - 4.2 V Offset)
I
L
V = 3.6 V,
I
(200 mA/div - 0.5 A Offset)
V
I
= 5 V,
O
= 500 mA,
= 1500 mA
O
I
LED
I
LIM
(200 mA/div - 0.3 A Offset)
Li-Polymer Battery at 3.3V, I
= 700 mA, I = 1500 mA
LIM
LED
t - Time = 50 ns/div
t - Time = 500 ns/div
Figure 17.
Figure 18.
LOW-LIGHT DIMMING MODE OPERATION
TORCH/FLASH SEQUENCE
FLASH_SYNC
(2 V/div)
SAFETY TIMER LIMITATION
Frequency = 121 Hz
Duty Cycle = 6.25%
I
LED
(500 mA/div)
I
LED
(20 mA/div)
V
OUT
(500 mV/div - 3.40 V Offset)
V
OUT
(200 mV/div - 3.5 V Offset)
LED Pin Headroom Voltage
(200 mV/div)
V
= 3.6 V, I
= 75 mA
TORCH
IN
V = 3.2 V, I
LIM
= 1500 mA
I
I
= 75 mA (Torch) to 700 mA (Flash)
LED
t - Time = 100 ms/div
t - Time = 2 ms/div
Figure 19.
Figure 20.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
TX-MASKING OPERATION
FLASH_SYNC
(2 V/div)
TX-MASKING OPERATION
V = 3.6 V, I
= 1500 mA
I
LIM
I
= 75 mA, I
= 700 mA
TORCH
FLASH
Tx-TOFF
(2 V/div)
Tx-TOFF
(2 V/div)
I
I
LED
LED
(200 mA/div)
(200 mA/div)
I
L
(500 mA/div)
I
L
(500 mA/div)
V = 3.6 V, I
= 1500 mA
I
LIM
I
= 75 mA, I
= 700 mA
FLASH
TORCH
t - Time = 10 ms/div
t - Time = 200 ms/div
Figure 21.
Figure 22.
TX-MASKING OPERATION
START-UP IN FLASH OPERATION
Tx-TOFF
(2 V/div)
V = 3.6 V, I
LIM
= 1500 mA ,I = 700 mA
FLASH
I
MODE0 = GND, FLASH_SYNC = HIGH
MODE1
(2 V/div)
V
OUT
(2 V/div)
I
LED
I
(200 mA/div)
LED
(500 mA/div)
I
L
(500 mA/div)
I
L
(200 mA/div)
V = 3.6 V, I
= 1500 mA
I
LIM
I
= 75 mA, I = 700 mA
FLASH
TORCH
t - Time = 200 ms/div
t - Time = 50 ms/div
Figure 23.
Figure 24.
12
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
DETAILED DESCRIPTION
OPERATION
The TPS6105x family employs a 2-MHz constant-frequency, current-mode PWM converter to generate the
output voltage required to drive high-power LEDs. The device integrates a power stage based on an NMOS
switch and a synchronous NMOS rectifier. The device also implements a linear low-side current regulator to
control the LED current when the battery voltage is higher than the diode forward voltage.
In boost mode, the duty cycle of the converter is set by the error amplifier and the saw-tooth ramp applied to the
comparator. Because the control architecture is based on a current-mode control, a compensation ramp is added
to allow stable operation at duty cycles larger than 50%. The converter is a fully-integrated synchronous-boost
converter, always operating in continuous-conduction mode. This allows low-noise operation, and avoids ringing
on the switch pin, which would be seen on a converter when entering discontinuous-conduction mode.
The TPS6105x device not only operates as a regulated current source but also as a standard voltage-boost
regulator. This additional operating mode can be useful to properly synchronize the converter when supplying
other high-power devices in the system, such as a hands-free audio power amplifier, or any other component
requiring a supply voltage higher than the battery voltage.
The mode of operation (shutdown, torch and flash modes, constant voltage regulation) selection is done via the
MODE0/1 control inputs.
Table 2. TPS6105x Operating Modes
MODE1 MODE0
OPERATING MODES
0
0
Power stage is in shutdown. The output is either connected directly to the battery via the rectifier’s body diode.
LED is turned-on for torch light operation. The converter is operating in the current regulation mode (CM).
The output voltage is controlled by the forward voltage characteristic of the LED.
0
1
LED is turned-on for flashlight operation. The converter is operating in the current regulation mode (CM).
The output voltage is controlled by the forward voltage characteristic of the LED.
1
1
0
1
LED is turned-off and the converter is operating in voltage regulation mode (VM).
The output voltage is regulated to 5.0V.
To simplify flash synchronization with the camera module, the device offers a FLASH_SYNC strobe input pin to
switch (with zero latency) the LED current from flash to torch light. The LED is driven at the flashlight current
level when a logic high signal is applied to the FLASH_SYNC pin.
The maximum duration of the flash pulse can be limited by means of an internal safety timer (820ms). The safety
timer starts on the rising edge of the FLASH_SYNC signal and stops either on its falling edge or after a timeout
whatever occurs first.
FLASH_SYNC
FLASH_SYNC
STIM
STIM
TIMER
TIMER
TIME-OUT
TORCH
FLASH
FLASH
TIME-OUT
TORCH
LED CONTROL
LED CONTROL
Figure 25. Level Sensitive Safety Timer (Timeout)
Figure 26. Level Sensitive Safety Timer
(Normal Operation + Timeout)
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
EFFICIENCY
The sense voltage has a direct effect on the converter’s efficiency. Because the voltage across the low-side
current regulator does not contribute to the output power (LED brightness), the lower the sense voltage, the
higher the efficiency will be.
When running in boost mode (VF(LED) > VIN), the voltage present at the LED pin of the low-side current regulator
is typically 250 mV, which contributes to high power-conversion efficiency.
When running in the linear down-converter mode (VF(LED) < VIN), the low-side current regulator drops the voltage
difference between the input voltage and the LED forward voltage. Depending on the input voltage and the LED
forward voltage characteristic, the converter displays efficiency of approximately 80% to 90%.
FLASH BLANKING
The TPS6105x device also integrates a Tx-TOFF input that can be used as flash masking input. This blanking
function turns the LED from flash to torch light, thereby reducing almost instantaneously the peak current loading
from the battery. This function has no influence on the safety timer duration.
IFLASH
LED Current
ITORCH
FLASH_SYNC
Tx-TOFF
Figure 27. Synchronized Flash With Blanking Periods (MODE0 = 0, MODE1 = 1)
LOW LIGHT DIMMING MODE
The TPS6105x device features white LED drive capability at very low light intensity. To generate a reduced LED
average current, the device employs a 122 Hz fixed frequency PWM modulation scheme. Operation is
understood best by referring to the timer block diagram.
The torch current is modulated with a 6.3% duty cycle. The low light dimming mode can only be activated in the
torch only mode (MODE1 = 0, MODE0 = 1) together with a logic level high applied to the FLASH_SYNC input.
ITORCH
ILED(DC)
=
0.063 x ITORCH
0
Figure 28. PWM Dimming Principle
White-LED blinking can be achieved by turning on/off periodically the LED dimmer via the (DIM) bit, see
Figure 29.
LED OFF
LED ON with Reduced Current
ITORCH
ITORCH
6.3% PWM Dimming Steps
MODE0
Figure 29. White LED Blinking Control (MODE1 = 0, FLASH_SYNC = 1)
14
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
SOFT-START
Since the output capacitor always remains biased to the input voltage, the TPS6105x can immediately start
switching once it has been enabled. The device starts-up by smoothly ramping up it’s internal reference voltage,
thus limiting the inrush current.
SHUTDOWN
In shutdown mode, the regulator stops switching and the LED pin is high impedance thus eliminating any DC
conduction path. The internal switch and rectifier MOSFET are turned off. VOUT is one body-diode drop below
the input voltage and the device consumes only a shutdown current of 0.3 µA (typ). The output capacitor remains
biased to the input voltage.
LED FAILURE MODES
If the LED fails as a short circuit, the low-side current regulator limits the maximum output current.
If the LED fails as an open circuit, the control loop initially attempts to regulate off of its low-side current regulator
feedback signal. This drives VOUT higher. Because the open-circuited LED will never accept its programmed
current, VOUT must be voltage-limited by means of a secondary control loop. In this failure mode, the TPS6105x
limits VOUT to 6.0 V (typ.).
UNDERVOLTAGE LOCKOUT
The undervoltage lockout circuit prevents the device from malfunctioning at low input voltages. It prevents the
converter from turning on the switch or rectifier MOSFET under undefined conditions.
THERMAL SHUTDOWN
As soon as the junction temperature, TJ, exceeds 160°C typical, the device goes into thermal shutdown. In this
mode, the boost power stage and the low-side current regulator are turned off. To resume operation, the device
needs to be cycled through a shutdown phase (MODE0 = 0, MODE1 = 0).
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
APPLICATION INFORMATION
INDUCTOR SELECTION
A boost converter requires two main passive components for storing energy during the conversion. A boost
inductor and a storage capacitor at the output are required. The TPS6105x device integrates a current limit
protection circuitry. The peak current of the NMOS switch is sensed to limit the maximum current flowing through
the switch and the inductor (e.g. 1000 mA or 1500 mA).
In order to optimize solution size the TPS6105x device has been designed to operate with inductance values
between a minimum of 1.3 µH and maximum of 2.9 µH. In typical high-current white LED applications a 2.2 µH
inductance is recommended.
To select the boost inductor, it is recommended to keep the possible peak inductor current below the current limit
threshold of the power switch in the chosen configuration. The highest peak current through the inductor and the
power switch depends on the output load, the input and output voltages. Estimation of the maximum average
inductor current and the maximum inductor peak current can be done using Equation 1 and Equation 2:
V
OUT
I [ I
+
L
OUT
h V
IN
(1)
(2)
IOUT
2 f L (1 * D) h
V
OUT * VIN
VOUT
VIN D
IL(PEAK)
+
)
with D +
with:
f = switching frequency (2 MHz)
L = inductance value (2.2 µH)
η = estimated efficiency (85%)
For example, for an output current of 500 mA at 5 V, the TPS6105x device needs to be set for a 1000 mA
current limit operation together with an inductor supporting this peak current.
The losses in the inductor caused by magnetic hysteresis losses and copper losses are a major parameter for
total circuit efficiency.
Table 3. List of Inductors
MANUFACTURER
TDK
SERIES
VLF3010AT
NR3010
DIMENSIONS
ILIM SETTINGS
2,6 mm × 2,8 mm × 1,0 mm max. height
3,0 mm × 3,0 mm × 1,0 mm max. height
2,5 mm × 2,0 mm × 1,2 mm max. height
2,6 mm × 2,8 mm × 1,4 mm max. height
3,0 mm × 3,0 mm × 1,5 mm max. height
3,0 mm × 3,0 mm × 1,5 mm max. height
3,0 mm × 3,0 mm × 1,2 mm max. height
TAIYO YUDEN
FDK
1000 mA (typ.)
MIPSA2520
VLF3014AT
LPS3015
TDK
COILCRAFT
MURATA
TOKO
1500 mA (typ.)
LQH3NP
FDSE0312
16
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
CAPACITOR SELECTION
Input Capacitor
For good input voltage filtering low ESR ceramic capacitors are recommended. A 10-µF input capacitor is
recommended to improve transient behavior of the regulator and EMI behavior of the total power supply circuit.
The input capacitor should be placed as close as possible to the input pin of the converter.
Output Capacitor
The primary parameter necessary to define the output capacitor is the maximum allowed output voltage ripple of
the converter. This ripple is determined by two parameters of the capacitor, the capacitance and the ESR. It is
possible to calculate the minimum capacitance needed for the defined ripple, supposing that the ESR is zero, by
using Equation 3:
ǒV
f DV V
INǓ
I
* V
OUT
OUT
C
[
min
OUT
(3)
Parameter f is the switching frequency and ΔV is the maximum allowed ripple.
With a chosen ripple voltage of 10mV, a minimum capacitance of 10 µF is needed. The total ripple is larger due
to the ESR of the output capacitor. This additional component of the ripple can be calculated using Equation 4:
ΔVESR = IOUT × RESR
The total ripple is the sum of the ripple caused by the capacitance and the ripple caused by the ESR of the
capacitor. Additional ripple is caused by load transients. This means that the output capacitor has to completely
supply the load during the charging phase of the inductor. A reasonable value of the output capacitance depends
on the speed of the load transients and the load current during the load change.
For the high current white LED application, a minimum of 3 µF effective output capacitance is usually required
when operating with 2.2 µH (typ) inductors. For solution size reasons, this is usually one or more X5R/X7R
ceramic capacitors. For stable operation of the internally compensated control loop, a maximum of 50 µF
effective output capacitance is tolerable.
Depending on the material, size and margin to the rated voltage of the used output capacitor, degradation on the
effective capacitance can be observed. This loss of capacitance is related to the DC bias voltage applied. It is
therefore always recommended to check that the selected capacitors are showing enough effective capacitance
under real operating conditions.
CHECKING LOOP STABILITY
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signals:
•
•
•
Switching node, SW
Inductor current, IL
Output ripple voltage, VOUT(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations the
regulation loop may be unstable. This is often a result of board layout and/or L-C combination.
The next step in regulation loop evaluation is to perform a load transient test. Output voltage settling time after
the load transient event is a good estimate of the control loop bandwidth. The amount of overshoot and
subsequent oscillations (ringing) indicates the stability of the control loop. Without any ringing, the loop has
usually more than 45° of phase margin.
Because the damping factor of the circuitry is directly related to several resistive parameters (e.g., MOSFET
rDS(on)) that are temperature dependant, the loop stability analysis has to be done over the input voltage range,
output current range, and temperature range.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
LAYOUT CONSIDERATIONS
As for all switching power supplies, the layout is an important step in the design, especially at high peak currents
and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as
well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground
tracks.
The input capacitor, output capacitor, and the inductor should be placed as close as possible to the IC. Use a
common ground node for power ground and a different one for control ground to minimize the effects of ground
noise. Connect these ground nodes at any place close to one of the ground pins of the IC.
To lay out the control ground, it is recommended to use short traces as well, separated from the power ground
traces. This avoids ground shift problems, which can occur due to superimposition of power ground current and
control ground current.
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependant issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the
power-dissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
•
•
•
Improving the power dissipation capability of the PCB design
Improving the thermal coupling of the component to the PCB
Introducing airflow in the system
Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where
high maximum power dissipation exists, special care must be paid to thermal dissipation issues in board design.
The maximum junction temperature (TJ) of the TPS6105x is 150°C.
The maximum power dissipation gets especially critical when the device operates in the linear down mode at
high LED current. For single pulse power thermal analysis (e.g., flash strobe), the allowable power dissipation for
the device is given by Figure 30.
4
No Airflow
3.5
3
2.5
2
t
= 85°C
1.5
1
PCB
0.5
0
Theta JB: 35°CW
0
100 200 300 400 500 600 700 800 900 1000
Pulse Width - ms
Figure 30. Single Pulse Power Capability (CSP Package)
18
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
www.ti.com .................................................................................................................................................. SLUS760A–SEPTEMBER 2007–REVISED MAY 2008
TYPICAL APPLICATIONS
TPS61054
L
2.2 mH
SW
SW
VBAT
VOUT
C
10 mF
P
OUT
AVIN
WHITE LED
FLASH-LIGHT
Li-Ion
C
IN
P
P
LED
MODE1
MODE0
CAMERA ENGINE
Tx-TOFF
FLASH_SYNC
PGND
PGND
P
AGND
RF PA TX ACTIVE
Figure 31. High Power White LED Solution Featuring No-Latency Turn-Down via PA TX Signal
TPS61054
L
SW
VBAT
VOUT
SW
2.2 mH
C
LED 1
1 .5 R
LED 2
OUT
10 mF
AVIN
Li-Ion
C
IN
P
1 .5 R
P
P
LED
MODE1
MODE0
LED 1, LED 2 VF variation
should be with 100 mV from each other
Tx-TOFF
FLASH _SYNC
AGND
PGND
PGND
P
Figure 32. 2 × 350 mA Dual LED Camera Flash
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s) :TPS61054, TPS61055
TPS61054, TPS61055
SLUS760A–SEPTEMBER 2007–REVISED MAY 2008 .................................................................................................................................................. www.ti.com
PACKAGE SUMMARY
CHIP SCALE PACKAGE
CHIP SCALE PACKAGE
(BOTTOM VIEW)
(TOP VIEW)
A3
B3
A2
B2
A1
B1
YMLLLLS
6105x
D
C3
D3
C2
D2
C1
D1
A1
E
Code:
•
•
•
Y — 2 digit date code
LLLL - lot trace code
S - assembly site code
PACKAGE DIMENSIONS
The dimensions for the YZG package are shown in Table 4. See the package drawing at the end of this data
sheet.
Table 4. YZG Package Dimensions
Packaged Devices
D
E
TPS6105xYZG
1.96 ±0.05 mm
1.46 ±0.05 mm
20
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s) :TPS61054, TPS61055
PACKAGE MATERIALS INFORMATION
www.ti.com
20-May-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
TPS61054DRCR
TPS61054DRCT
TPS61055DRCR
TPS61055DRCT
SON
SON
SON
SON
DRC
DRC
DRC
DRC
10
10
10
10
3000
250
330.0
180.0
330.0
180.0
12.4
12.4
12.4
12.4
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
1.1
1.1
1.1
1.1
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
Q2
Q2
Q2
Q2
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-May-2008
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS61054DRCR
TPS61054DRCT
TPS61055DRCR
TPS61055DRCT
SON
SON
SON
SON
DRC
DRC
DRC
DRC
10
10
10
10
3000
250
346.0
190.5
346.0
190.5
346.0
212.7
346.0
212.7
29.0
31.8
29.0
31.8
3000
250
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
Logic
Military
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
相关型号:
TPS61055DRCT
HIGH POWER WHITE LED DRIVER 2-MHz SYNCHRONOUS BOOST CONVERTER WITH STANDARD LOGIC INTERFACE
TI
TPS61055YZG
HIGH POWER WHITE LED DRIVER 2-MHz SYNCHRONOUS BOOST CONVERTER WITH STANDARD LOGIC INTERFACE
TI
©2020 ICPDF网 联系我们和版权申明