TPS62231TDRYRQ1 [TI]
3 MHz Ultra Small Step Down Converter in 1x1.5 SON Package; 3 MHz的超小型降压转换器, 1x1.5 SON封装型号: | TPS62231TDRYRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 3 MHz Ultra Small Step Down Converter in 1x1.5 SON Package |
文件: | 总32页 (文件大小:1340K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
3 MHz Ultra Small Step Down Converter in 1x1.5 SON Package
Check for Samples: TPS62231-Q1, TPS622314-Q1
1
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
Qualified for Automotive Applications
The TPS6223x-Q1 device family is a high frequency
synchronous step down DC-DC converter optimized
for battery powered portable applications. It supports
up to 500 mA output current and allows the use of
tiny and low cost chip inductors and capacitors.
3 MHz Switch Frequency
Up to 94% Efficiency
Output Peak Current up to 500 mA
Excellent AC and Transient Load Regulation
High PSRR (up to 90 dB)
With a wide input voltage range of 2.05 V to 6 V the
device supports applications powered by Li-Ion
batteries with extended voltage range. The minimum
input voltage of 2.05 V allows as well the operation
from Li-primary or two alkaline batteries. Different
fixed output voltage versions are available from 1 V to
3.3 V.
Small External Output Filter Components 1 μH/
4.7 μF
•
•
VIN range from 2.05 V to 6 V
Optimized Power Save Mode For Low Output
Ripple Voltage
The TPS6223x-Q1 series features switch frequency
up to 3.8 MHz. At medium to heavy loads, the
converter operates in PWM mode and automatically
enters Power Save Mode operation at light load
currents to maintain high efficiency over the entire
load current range.
•
•
•
•
•
•
•
Forced PWM Mode Operation
Typ. 22 μA Quiescent Current
100% Duty Cycle for Lowest Dropout
Small 1 × 1.5 × 0.6mm3 SON Package
12 mm2 Minimum Solution Size
Because of its excellent PSRR and AC load
regulation performance, the device is also suitable to
replace linear regulators to obtain better power
conversion efficiency.
Supports 0.6 mm Maximum Solution Height
Soft Start with typ. 100μs Start Up Time
APPLICATIONS
The Power Save Mode in TPS6223x-Q1 reduces the
quiescent current consumption down to 22 μA during
light load operation. It is optimized to achieve very
low output voltage ripple even with small external
component and features excellent ac load regulation.
•
•
•
•
•
•
LDO Replacement
Portable Audio, Portable Media
Cell Phones
Low Power Wireless
Low Power DSP Core Supply
Digital Cameras
For very noise sensitive applications, the device can
be forced to PWM Mode operation over the entire
load range by pulling the MODE pin high. In the
shutdown mode, the current consumption is reduced
to less than 1μA. The TPS6223x-Q1 is available in a
1 × 1.5mm2 6 pin SON package.
V
IN
L
TPS62231
1/2.2 mH
V
2.05 V - 6 V
OUT
VIN
SW
1.8 V
C
FB
EN
IN
C
OUT
MODE
GND
2.2 mF
4.7 mF
Total area
12mm²
L1
V
IN
C2
GND
V OUT
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION(1)
PACKAGE
DESIGNATOR
PACKAGE
MARKING
OUTPUT
VOLTAGE
FREQUENCY
[MHz]
TA
PART NUMBER
TPS62231-Q1
ORDERING
1.8 V
1.5 V
3
3
DRY
DRY
TPS62231TDRYRQ1
TPS622314TDRYRQ1
31
14
–40°C to 105°C
TPS622314-Q1
(1) For detailed ordering information see the PACKAGE OPTION ADDENDUM at the end of this data sheet.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
(1)
VALUE
UNIT
MIN
MAX
Voltage at VIN and SW Pin(2)
Voltage at EN, MODE Pin(2)
–0.3
–0.3
–0.3
7
V
V
V
A
VI
VIN +0.3, ≤7
(2)
Voltage at FB Pin
3.6
Peak output current
internally limited
Human Body Model (HBM)
2
1
kV
V
ESD rating(3)
Charged Device Model CDM)
Machine Model (MM)
200
Power dissipation
Internally limited
TJ
Maximum operating junction temperature
Storage temperature range
–40
–65
125
150
°C
°C
Tstg
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
(3) The human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin. The machine model is a 200-pF
capacitor discharged directly into each pin.
DISSIPATION RATINGS(1)
POWER RATING
FOR TA ≤ 25°C
DERATING FACTOR
ABOVE TA = 25°C
PACKAGE
RθJA
1 × 1.5 SON
234°C/W(2)
420 mW
4.2 mW/°C
(1) Maximum power dissipation is a function of TJ(max), θJA and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = [TJ(max) – TA] /θJA
(2) This thermal data is measured with high-K board (4 layers board according to JESD51-7 JEDEC standard).
.
2
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
RECOMMENDED OPERATING CONDITIONS
operating ambient temperature TA = –40 to 105°C (unless otherwise noted)(1)
MIN
NOM
MAX UNIT
(2)
Supply voltage VIN
2.05
6
V
Effective inductance
Effective capacitance
2.2
4.7
3
μH
μF
2
(4)
(4)
V
OUT ≤ VIN -1 V(3)
500 mA maximum IOUT
350 mA maximum IOUT
3.6
2.7
Recommended minimum
supply voltage
2.5
V
VOUT ≤ 1.8V
60 mA maximum output current(4)
2.05
125
Operating junction temperature range, TJ
–40
°C
(1) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA(max)) is dependent on the maximum operating junction temperature (TJ(max)), the
maximum power dissipation of the device in the application (PD(max)), and the junction-to-ambient thermal resistance of the part/package
in the application (θJA), as given by the following equation: TA(max) = TJ(max) – (θJA × PD(max)).
(2) The minimum required supply voltage for startup is 2.05 V. The part is functional down to the falling UVL (Under Voltage Lockout)
threshold.
(3) For a voltage difference between minimum VIN and VOUT of ≥ 1 V
(4) Typical value applies for TA = 25°C, maximum value applies for TA = 105°C with TJ ≤ 125°C, PCB layout needs to support proper
thermal performance.
Copyright © 2011, Texas Instruments Incorporated
3
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
VIN = 3.6V, VOUT = 1.8V, EN = VIN, MODE = GND, TA = –40°C to 105°C(1) typical values are at TA = 25°C (unless otherwise
noted), CIN = 2.2μF, L = 2.2μH, COUT = 4.7μF, see parameter measurement information
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
SUPPLY
(2)
VIN
Input voltage range
2.05
6
V
IOUT = 0mA. PFM mode enabled (Mode = 0)
device not switching
22
25
40
μA
IOUT = 0mA. PFM mode enabled (Mode = 0)
device switching, VIN = 3.6V, VOUT = 1.2V
μA
IQ
Operating quiescent current
IOUT = 0 mA. Switching with no load
(MODE/DATA = VIN), PWM operation,
VOUT = 1.8V, L = 2.2μH
3
mA
ISD
Shutdown current
EN = GND(3)
0.1
1.8
1.9
1
1.9
μA
V
Falling
UVLO
Undervoltage lockout threshold
Rising
2.05
V
ENABLE, MODE THRESHOLD
VIH TH Threshold for detecting high EN, MODE 2.05 V ≤ VIN ≤ 6V , rising edge
VIL TH HYS Threshold for detecting low EN, MODE 2.05 V ≤ VIN ≤ 6V , falling edge
0.8
0.6
1
V
V
0.4
IIN
Input bias Current, EN, MODE
EN, MODE = GND or VIN = 3.6V
0.01
0.5
μA
POWER SWITCH
High side MOSFET on-resistance
600
350
850
480
RDS(ON)
VIN = 3.6V, TJmax = 105°C; RDS(ON) max value
mΩ
Low Side MOSFET on-resistance
Forward current limit MOSFET
high-side
690
550
850
1050 mA
ILIMF
TSD
VIN = 3.6V, open loop
Forward current limit MOSFET low side
Thermal shutdown
840
150
20
1220 mA
Increasing junction temperature
Decreasing junction temperature
°C
°C
Thermal shutdown hysteresis
CONTROLLER
tONmin
Minimum ON time
VIN 3.6V, VOUT = 1.8V, Mode = high, IOUT = 0 mA
135
40
ns
ns
tOFFmin
OUTPUT
VREF
Minimum OFF time
Internal Reference Voltage
0.70
0%
V
VIN = 3.6V, Mode = GND, device operating in PFM
Mode, IOUT = 0mA
Output voltage accuracy(4)
VIN = 3.6V, MODE = VIN
IOUT = 0 mA
,
TA = 25°C
–2.0%
–2.5%
2.0%
2.5%
VOUT
TA = –40°C to
105°C
DC output voltage load regulation
DC output voltage line regulation
PWM operation, Mode = VIN = 3.6V, VOUT = 1.8 V
0.001
0
%/mA
%/V
IOUT = 0 mA, Mode = VIN, 2.05V ≤ VIN ≤ 6V
Time from active EN to VOUT = 1.8V, VIN = 3.6V,
10Ω load
VIN = VOUT = VSW = 3.6 V, EN = GND(5)
tStart
Start-up Time
100
0.1
μs
ILK_SW
Leakage current into SW pin
0.5
μA
(1) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA(max)) is dependent on the maximum operating junction temperature (TJ(max)), the
maximum power dissipation of the device in the application (PD(max)), and the junction-to-ambient thermal resistance of the
part/package in the application (θJA), as given by the following equation: TA(max) = TJ(max) – (θJA × PD(max)).
(2) The minimum required supply voltage for startup is 2.05V. The part is functional down to the falling UVL (Under Voltage Lockout)
threshold
(3) Shutdown current into VIN pin, includes internal leakage
(4) VIN = VO + 1.0 V
(5) The internal resistor divider network is disconnected from FB pin.
4
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
DRY PACKAGE
(TOP VIEW)
6
5
4
1
2
3
MODE
SW
FB
EN
VIN
GND
PIN FUNCTIONS
PIN
I/O
DESCRIPTION
NAME
VIN
NO
3
PWR VIN power supply pin.
PWR GND supply pin
GND
EN
4
5
IN
This is the enable pin of the device. Pulling this pin to low forces the device into shutdown mode. Pulling
this pin to high enables the device. This pin must be terminated.
SW
2
OUT
This is the switch pin and is connected to the internal MOSFET switches. Connect the inductor to this
terminal
FB
6
1
IN
IN
Feedback Pin for the internal regulation loop. Connect this pin directly to the output capacitor.
MODE
MODE pin = high forces the device to operate in PWM mode. Mode = low enables the Power Save Mode
with automatic transition from PFM (Pulse frequency mode) to PWM (pulse width modulation) mode.
FUNCTIONAL BLOCK DIAGRAM
VIN
Undervoltage
Lockout
VREF
0.70 V
Current
Bandgap
Limit Comparator
Limit
High Side
MODE
Softstart
MODE
PMOS
VIN
Gate Driver
Anti
Shoot-Through
Min. On Time
Control
Logic
SW
FB
EN
FB
Min. OFF Time
VREF
NMOS
Limit
Low Side
Integrated
Feed Back
Network
Error
Comparator
Thermal
Shutdown
Zero/Negative
Current Limit Comparator
EN
GND
Copyright © 2011, Texas Instruments Incorporated
5
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
PARAMETER MEASUREMENT INFORMATION
TPS6223X
L = 1/2.2 mH
V
= 2.05 V to 6 V
IN
V
OUT
VIN
SW
FB
C
C
EN
IN
OUT
2.2 mF
4.7 mF
MODE
GND
C
: Murata GRM155R60J225ME15D 2.2 mF 0402 size
IN
C
C
: Murata GRM188R60J475ME 4.7 mF 0603 size, VOUT >= 1.8 V
: Taiyo Yuden AMK105BJ475MV 4.7 mF 0402 size, VOUT = 1.2 V
OUT
OUT
l: Murata LQM2HPN1R0MJ0 1 mH, LQM2HPN2R2MJ0 2.2 mH,
size 2.5x2.0x1.2mm3
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
1, 2, 3, 4, 5, 6, 7
8, 9, 10, 11
η
η
Efficiency
Efficiency
vs Load current
vs Output Current
12, 13, 14, 15,
16, 17
VO
Output voltage
vs Output current
18, 19, 20, 21,
22, 23, 24, 25,
26, 27
Switching frequency
vs Output current
Output voltage peak to peak
Quiescent current
vs Output current
28,29
IQ
vs Ambient temperature
vs Ambient temperature
30
ISD
Shutdown current
31
PMOS Static drain-source on-state resistance
NMOS Static drain-source on-state resistance
Power supply rejection ratio
Typical operation
vs Supply voltage and ambient temperature
vs Supply voltage and ambient temperature
vs Frequency
32
rDS(ON)
PSRR
33
34
35, 36, 37
PFM
38
Line transient response
PWM
39
40
Mode transition PFM / forced PWM
AC - load regulation performance
Load transient response
41 42, 43
44, 45, 46, 47
48, 49
50
Start-up
Spurious Output Noise, 12R Load
Spurious Output Noise, 100R Load
51
6
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
100
100
90
80
70
60
50
40
30
20
10
0
V
= 3.6 V
= 2.9 V
IN
V
= 2.9 V
IN
90
80
70
60
V
= 3.6 V
IN
V
= 4.2 V
IN
V
IN
V
= 4.2 V
IN
V
= 5 V
IN
V
= 5 V
IN
50
40
30
20
10
0
MODE = GND,
= 2.5V,
MODE = V
,
V
IN
= 2.5 V,
OUT
V
L = 2.2 mH (LQM2HPN2R2MJ0)
= 4.7 mF
OUT
C
L = 2.2 mH (LQM2HPN2R2MJ0)
= 4.7 mF
OUT
C
OUT
0.1
1
I
10
- Output Current - mA
100
1000
1
10
I - Output Current - mA
O
100
1000
O
Figure 1. Efficiency PFM/PWM Mode 2.5V Output Voltage
Figure 2. Efficiency Forced PWM Mode 2.5V Output
Voltage
100
90
80
70
60
50
100
90
80
70
60
50
40
30
20
10
0
V
= 2.3 V
IN
V
= 2.3 V
IN
V
= 2.7 V
V
= 2.7 V
IN
IN
V
= 3.3 V
IN
V
= 3.3 V
V
= 3.6 V
IN
IN
V
= 3.6 V
IN
V
= 4.2 V
IN
V
= 4.2 V
V
= 5 V
IN
IN
40
30
20
V
= 5 V
IN
MODE = GND,
= 1.8 V,
MODE = V
,
IN
= 1.8 V,
V
OUT
V
OUT
L = 2.2 mH (MIPSA25202R2),
= 4.7 mF
L = 2.2 mH (MIPSA25202R2),
= 4.7 mF
C
10
0
OUT
C
OUT
0.1
1
I
10
- Output Current - mA
100
1000
1
10
100
1000
I - Output Current - mA
O
O
Figure 3. Efficiency PFM/PWM MODE 1.8V Output Voltage
Figure 4. Efficiency Forced PWM Mode 1.8V Output
voltage
Copyright © 2011, Texas Instruments Incorporated
7
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
100
100
V
= 2.3 V
IN
90
90
80
70
60
50
V
= 2.3 V
80
70
60
IN
V
= 2.7 V
IN
V
= 2.7 V
IN
V
= 3.6 V
IN
V
= 3.6 V
IN
V
= 4.2 V
IN
V
= 4.2 V
50
40
30
20
IN
V
= 5 V
IN
V
= 5 V
40
30
20
10
0
IN
MODE = GND,
= 1.2 V,
MODE = V
,
IN
= 1.2 V,
V
OUT
V
OUT
L = 2.2 mH MIPSZ2012 2R2 (2012 size),
= 4.7 mF
L = 2.2 mH MIPSZ2012 2R2 (2012 size),
= 4.7 mF
C
10
0
OUT
C
OUT
1
10 100
- Output Current - mA
1000
0.1
1
10
- Output Current - mA
100
1000
I
I
O
O
Figure 5. Efficiency PFM/PWM Mode 1.2V Output voltage
Figure 6. Efficiency Forced PWM Mode 1.2V Output
Voltage
100
90
80
70
60
50
40
30
20
10
0
90
V
= 3.6 V
IN
85
80
75
70
65
60
55
50
V
= 4.2 V
IN
V
= 5 V
IN
MIPSA25202R2
L = 2.2 mH
(2.5x2x1.2mm3)
MIPSD1R0
L = 1 mH 0805
(2x1.25x1mm3)
LQM2HPN1R0MJ0
L = 1 mH
(2.5x2x1.2mm3)
MIPSZ2012D2R2
L = 2.2 mH 0805
(2x1.25x1mm3)
LQM21PN2R2
L = 2.2 mH 0805
(2x1.25x0.55mm3)
MODE = GND,
TPS62233
MODE = GND,
C
C
V
= 2.2 mF (0402),
IN
V
= 3 V,
= 4.7 mF (0402),
OUT
OUT
L = 1 mH,
= 4.7 mF
= 1.8 V,
100
OUT
C
OUT
V
= 3.6 V
IN
0.1
1
10
- Output Current - mA
100
1000
0.1
1
10
1000
I
I
- Output Current - mA
O
O
Figure 7. Comparison Efficiency vs Inductor Value and
Size
Figure 8. Comparison Efficiency vs IOUT – TPS62233
8
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
100
90
80
70
60
V
= 3.3 V
IN
V
= 3.3 V
IN
90
80
70
60
50
V
= 3.6 V
IN
V
= 3.6 V
IN
V
= 4.2 V
IN
V
= 4.2 V
IN
50
40
30
40
30
TPS62236
V
V
= 1.2 V PFM,
OUT
MODE = GND
= 1.85 V PFM
OUT
0.1
1
10
- Output Current - mA
100
1000
0.1
1
10
- Output Current - mA
100
1000
I
I
O
O
Figure 9. Comparison Efficiency vs IOUT – TPS62235
Figure 10. Comparison Efficiency vs IOUT – TPS62236
2.575
2.55
90
80
70
60
50
V
= 3.3 V
MODE = V
,
IN
IN
= 2.5 V,
V
OUT
L = 1 mH,
C
T
= 4.7 mF,
OUT
V
= 3.6 V
IN
= 25°C
A
V
= 3.3 V
IN
V
= 4.2 V
2.525
2.5
IN
V
= 3.6 V
IN
V
= 4.2 V
IN
V
= 5 V
2.475
IN
40
30
2.45
TPS622311
V
= 1.1 V PFM
OUT
2.425
0.1
1
I
10
- Output Current - mA
100
1000
0.1
1
10
- Output Current - mA
100
1000
I
O
O
Figure 11. Comparison Efficiency vs IOUT – TPS622311
Figure 12. 2.5V Output Voltage Accuracy forced PWM
Mode
Copyright © 2011, Texas Instruments Incorporated
9
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
1.854
2.575
2.55
MODE = GND,
= 2.5 V,
MODE = GND,
= 1.8 V,
V
OUT
V
OUT
L = 1 mH,
L = 2.2 mH,
1.836
1.818
C
T
= 4.7 mF,
OUT
C
T
= 4.7 mF,
OUT
= 25°C
A
= 25°C
A
V
= 4.2 V
= 3.3 V
IN
V
= 5 V
2.525
2.5
IN
V
= 3.6 V
= 4.2 V
V
= 3.3 V
IN
IN
1.8
1.782
1.764
1.746
V
IN
V
= 3.6 V
IN
V
IN
2.475
V
= 5 V
IN
2.45
2.425
0.1
1
10
- Output Current - mA
100
1000
0.01
0.1
1
10
- Output Current - mA
100
1000
I
I
O
O
Figure 13. 2.5V Output Voltage Accuracy PFM/PWM Mode
Figure 14. 1.8V Output Voltage Accuracy PFM/PWM Mode
1.854
1.236
MODE = V
,
MODE = V
,
IN
= 1.2 V,
IN
= 1.8 V,
V
V
OUT
OUT
1.836
1.818
1.8
1.224
1.212
1.2
L = 2.2 mH,
L = 1 mH,
C
T
= 4.7 mF,
C
T
= 4.7 mF,
OUT
OUT
= 25°C
= 25°C
V = 3.3 V
IN
A
A
V
= 3.3 V
IN
V
= 3.6 V
IN
V
= 3.6 V
IN
V
= 5 V
IN
V
= 4.2 V
V
IN
V
= 4.2 V
1.188
1.782
IN
= 5 V
IN
1.176
1.164
1.764
1.746
0.1
1
I
10
- Output Current - mA
100
1000
0.1
1
I
10
- Output Current - mA
100
1000
O
O
Figure 15. 1.8V Output Voltage Accuracy Forced PWM
MODE
Figure 16. 1.2V Output Voltage Accuracy Forced PWM
MODE
10
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
4000
1.236
1.224
1.212
1.2
MODE = GND,
= 1.2 V,
V
OUT
3500
3000
V
= 5 V
IN
L = 2.2 mH,
C
T
= 4.7 mF,
OUT
V
= 4.2 V
IN
= 25°C
A
V
= 3.6 V
IN
V
= 3.3 V
IN
V
= 3.3 V
IN
2500
2000
1500
1000
V
= 3.6 V
IN
V
= 4.2 V
IN
1.188
V
= 5 V
IN
MODE = GND,
= 1.8 V,
V
V
= 2.7 V
OUT
IN
L = 2.2 mH,
1.176
1.164
V
= 2.3 V
500
0
C
T
= 4.7 mF,
OUT
= 25°C
IN
A
0
100
200 300
- Output Current - mA
400
500
0.01
0.1
1
10
- Output Current - mA
100
1000
I
I
O
O
Figure 17. 1.2V Output Voltage Accuracy PFM/PWM MODE
Figure 18. Switching Frequency vs Output Current, 1.8V
Output Voltage MODE = GND
4000
4000
V
= 5 V
V
IN
V
= 5 V
V
IN
= 4.2 V
V
= 4.2 V
IN
3500
3000
2500
2000
1500
3500
3000
2500
2000
1500
IN
V
= 3.6 V
V
= 3.6 V
V
IN
IN
= 3.3 V
IN
= 3.3 V
IN
MODE = GND,
= 1.8 V,
MODE = V
,
IN
= 1.8 V,
V
1000
500
0
1000
500
0
V
= 2.7 V
OUT
IN
V
OUT
V
= 2.7 V
IN
L = 1 mH,
L = 2.2 mH,
V
= 2.3 V
V
= 2.3 V
100
IN
IN
C
T
= 4.7 mF,
OUT
C
T
= 4.7 mF,
OUT
= 25°C
A
= 25°C
A
0
100
I
200 300
- Output Current - mA
400
500
0
200
- Output Current - mA
O
300
400
500
I
O
Figure 19. Switching Frequency vs Output Current, 1.8V
Output Voltage MODE = GND
Figure 20. Switching Frequency vs Output Current, 1.8V
Output Voltage MODE = VIN
Copyright © 2011, Texas Instruments Incorporated
11
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
4000
4000
V
= 5 V
V
MODE = V
,
IN
MODE = GND,
= 2.5 V,
IN
= 2.5 V,
OUT
V
= 4.2 V
V
OUT
IN
3500
3000
2500
2000
1500
1000
V
= 5 V
3500
3000
2500
2000
1500
1000
IN
L = 2.2 mH,
L = 2.2 mH,
V
= 3.6 V
IN
V
= 4.2 V
C
T
= 4.7 mF,
C
T
= 4.7 mF,
OUT
= 25°C
IN
OUT
V
= 3.3 V
IN
= 25°C
A
A
V
= 3.6 V
IN
V
= 3.3 V
IN
V
= 3 V
100
V
= 3 V
500
0
500
0
IN
IN
0
200 300
- Output Current - mA
400
500
0
100
200 300
- Output Current - mA
400
500
I
I
O
O
Figure 21. Switching Frequency vs Output Current, 2.5V
Output Voltage MODE = GND
Figure 22. Switching Frequency vs Output Current, 2.5V
Output Voltage MODE = VIN
3000
2500
2000
1500
1000
3500
3000
2500
2000
1500
1000
500
V
= 5 V
IN
V
= 5 V
IN
V
= 4.2 V
IN
V
= 4.2 V
V
IN
V
= 3.3 V
IN
= 3.6 V
IN
V
= 3.6 V
V
IN
V
= 3.3 V
IN
= 2.7 V
IN
V
= 2.3 V
IN
V
= 2.7 V
V
= 2 V
IN
IN
MODE = GND,
= 1.2 V,
V
= 2.3 V
IN
MODE = V
,
IN
= 1.2 V,
V
OUT
V
= 2 V
IN
V
OUT
L = 2.2 mH,
500
0
L = 2.2 mH,
C
T
= 4.7 mF,
OUT
C
T
= 4.7 mF,
OUT
= 25°C
A
= 25°C
A
0
0
100
200 300
- Output Current - mA
400
500
0
100
200
300
400
500
I
I - Output Current - mA
O
O
Figure 23. Switching Frequency vs Output Current, 1.2V
Output Voltage MODE = GND
Figure 24. Switching Frequency vs Output Current, 1.2V
Output Voltage MODE = VIN
12
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
3000
2500
V
= 5 V
IN
V
= 4.2 V
V
= 5 V
V
IN
IN
2500
2000
1500
1000
V
= 3.6 V
IN
2000
1500
1000
= 4.2 V
IN
V
= 2.3 V
V
= 2.7 V
V
= 3.3 V
IN
IN
IN
V
= 3.3 V
IN
V
= 3.6 V
IN
TPS62235
MODE = GND,
= 1.2 V,
TPS62236
MODE = GND,
V
= 2.7 V
IN
V
500
0
OUT
V
= 1.85 V,
500
0
OUT
V
= 2.3 V
IN
L = 2.2 mH,
= 4.7 mF
L = 2.2 mH,
= 4.7 mF
C
OUT
C
OUT
0
0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
- Output Current - A
0
0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45
- Output Current - A
I
I
O
O
Figure 25. Switching Frequency vs Output Current, 1.2V
Output Voltage MODE = PFM – TPS62235
Figure 26. Switching Frequency vs Output Current, 1.85V
Output Voltage MODE = PFM –TPS62236
3000
50
TPS62230
= 2.5 V,
V
45
40
35
30
25
20
15
10
5
O
L = 2.2 mH 2012,
(MIPSZ2012),
2500
2000
1500
1000
V
= 5 V
IN
C
= 4.7 mF 0402
O
V
= 4.2 V
IN
V = 3.3 V
I
V
= 2.7 V
IN
V = 3.6 V
V
= 3.3 V
I
IN
V
= 2.3 V
IN
TPS622311
MODE = GND,
V
= 1.1 V,
OUT
500
0
L = 2.2 mH,
= 4.7 mF
V = 4.2 V
I
C
OUT
0
0
0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
- Output Current - A
0
50 100 150 200 250 300 350 400 450 500
- Output Current - mA
I
I
O
O
Figure 27. Switching Frequency vs Output Current, 1.1V
Figure 28. Output Voltage, Peak-to-Peak vs Output Current
- TPS62230
Output Voltage MODE = PFM – TPS622311
Copyright © 2011, Texas Instruments Incorporated
13
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
35
30
TPS62230
= 1.8 V,
V
O
T = 85°C
A
25
20
15
10
5
T
= 60°C
L = 2.2 mH 2012,
(MIPSZ2012),
T
= 25°C
A
A
30
25
20
15
10
C
= 4.7 mF 0402
O
V = 3.3 V
I
V = 3.6 V
I
T
A
= -40°C
V = 4.2 V
I
0
2
2.5
3
3.5
4
4.5
- Input Voltage - V
5
5.5
6
0
50 100 150 200 250 300 350 400 450 500
- Output Current - mA
V
IN
I
O
Figure 29. Output Voltage, Peak-to-Peak vs Output
Current – TPS62231-Q1
Figure 30. Quiescent Current IQ vs Ambient Temperature
TA
0.2
2
PMOS
0.18
0.16
0.14
0.12
0.1
T
= 85°C
1.8
1.6
1.4
1.2
1
T
= 85°C
A
A
T
= 60°C
A
T
= 25°C
A
T
A
= -40°C
0.08
0.06
0.04
0.8
0.6
0.4
0.2
0
T
= -40°C
A
T
= 25°C
T
= 60°C
A
A
0.02
0
2
2.5
3
3.5
4
4.5
- Input Voltage - V
5
5.5
6
2
2.5
3
3.5
4
4.5
- Input Voltage - V
5
5.5
6
V
V
IN
IN
Figure 31. Shutdown Current ISD vs Ambient Temperature
TA
Figure 32. PMOS RDS(ON) vs Supply Voltage VIN and
Ambient Temperature TA
14
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
100
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
I
= 50 mA,
OUT
MODE = 0,
forced PWM
NMOS
90
T
= 85°C
T
A
80
70
= 60°C
T
A
= 25°C
A
60
50
40
30
20
10
0
I
= 50 mA,
T
A
= -40°C
OUT
MODE = 1,
PFM/PWM
I
= 150 mA,
OUT
PWM Mode
V
V
= 3.6 V,
IN
= 1.8 V,
= 2.2 mF,
= 4.7 mF,
OUT
C
C
IN
OUT
L = 2.2 mH
10
100
1k 10k
f - Frequency - kHz
100k
1M
2
2.5
3
3.5
4
4.5
- Input Voltage - V
5
5.5
6
V
IN
Figure 33. NMOS RDS(ON) vs Supply Voltage VIN and
Ambient Temperature TA
Figure 34. TPS62231 1.8V PSRR
SW
V
= 3.6 V
IN
2 V/div
V
= 2.5V
C
= 4.7 mF
OUT
OUT
20 mV/div
L = 2.2 mH
V
= 3.6V
MODE = GND
IN
SW
C
= 4.7 mF
I
= 10 mA
V
= 2.5V
OUT
L = 1 mH
OUT
OUT
2 V/div
20 mV/Div
MODE = GND
I
= 10 mA
OUT
I
I
L
L
200 mA/Div
200 mA/div
t - Time - 1 ms/div
Figure 35. PFM Mode Operation IOUT = 10mA
t - Time - 1 ms/div
Figure 36. PFM Mode Operation IOUT = 10mA
Copyright © 2011, Texas Instruments Incorporated
15
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
V
= 3.6 V
MODE = V
IN
IN
C
= 4.7 mF
I
= 10 mA
OUT
V
= 2.5 V
OUT
OUT
V
= 3.6 V to 4.2 V
IN
L = 1 mH
20 mV/div
200 mV/div
SW
2 V/div
I
L
200 mA/div
V
= 1.8 V
C
= 4.7 mF
OUT
OUT
20 mV/div
L = 2.2 mH
MODE = GND
= 50 mA
I
OUT
t - Time - 500 ns/div
Figure 37. Forced PWM Mode Operation IOUT = 10mA
t - Time - 10 ms/div
Figure 38. Line Transient Response PFM Mode
MODE: 0 V to 3.6 V
2 V/div
Forced PWM
Mode Operation
V
= 3.6 V to 4.2 V
IN
200 mV/div
PFM Mode Operation
V
SW
2 V/div
V
= 3.6 V,
IN
C
= 4.7 mF
OUT
I
COIL
200 mA/div
L = 1 mH
= 10 mA
I
OUT
C
= 4.7 mF
OUT
V
= 1.8 V
OUT
L = 2.2 mH
MODE = V
20 mV/div
IN
V
= 1.8 V
OUT
20 mV/div
I
= 50 mA
OUT
t - Time - 1 ms/div
t - Time - 100 ms/div
Figure 39. Line Transient Response PWM Mode
Figure 40. Mode Transition PFM / Forced PWM Mode
16
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
V
= 3.6 V
IN
V
= 2.5 V
V
= 2.5 V
OUT
OUT
C
= 4.7 mF
OUT
50 mV/div
50 mV/div
L = 2.2 mH
MODE = GND
V
= 3.6 V
IN
I
= 5 mA to 200 mA
C
= 4.7 mF
OUT
IOUT = 5mA to 200mA
sinusoidal
OUT
sinusoidal
100 mA/div
L = 2.2 mH
MODE = V
100mA/Div
IN
I
I
L
L
200 mA/div
200 mA/div
t - Time - 5 ms/div
Figure 41. AC – Load Regulation Performance 2.5V VOUT
t - Time - 5 ms/div
Figure 42. AC – Load Regulation Performance 2.5V VOUT
PFM Mode
PWM Mode
V
= 3.6 V
IN
V
= 2.5 V
C
= 4.7 mF
OUT
OUT
V
= 1.8 V
OUT
50 mV/div
L = 2.2 mH
MODE = GND
50 mV/div
V
= 3.6 V
IN
I
= 5 mA to 150 mA, 50 kHz
OUT
C
= 4.7 mF
OUT
sinusoidal 100 mA/div
I
= 5 mA to 200 mA
L = 1 mH
MODE = GND
OUT
100 mA/div
I
L
I
L
200 mA/div
200 mA/div
t - Time - 4 ms/div
t - Time - 5 ms/div
Figure 44. Load Transient Response 5mA to 200mA PFM
Figure 43. AC – Load Regulation Performance 1.8V VOUT
PFM Mode
to PWM Mode, VOUT 2.5V
Copyright © 2011, Texas Instruments Incorporated
17
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
V
= 3.6 V
IN
C
= 4.7 mF
V
= 2.5 V
OUT
OUT
50 mV/div
V
= 1.8 V
OUT
L = 2.2 mH
MODE = GND
50 mV/div
V
= 3.6 V
IN
C
= 4.7 mF
OUT
I
= 5 mA to 200 mA
OUT
L = 1 mH
100 mA/div
MODE = V
IN
I
= 5 mA to 150 mA
OUT
100 mA/div
I
I
L
L
200 mA/div
200 mA/div
t - Time - 10 ms/div
t - Time - 5 ms/div
Figure 45. Load Transient Response 5mA to 200mA,
Forced PWM Mode, VOUT 2.5V
Figure 46. Load Transient Response 5mA to 150mA, PFM
to PWM Mode, VOUT 1.8V
V
= 3.6 V
IN
C
= 4.7 mF
EN
OUT
V
= 1.8 V
2 V/div
OUT
L = 2.2 mH
MODE = V
50 mV/div
IN
SW
2 V/div
V
= 3.6 V
IN
V
= 0 V to 2.5 V
C
= 4.7 mF
OUT
OUT
1 V/div
I
= 5 mA to 150 mA
L = 1 mH
OUT
MODE = GND
Load = 20 R
100 mA/div
I
L
I
200 mA/div
IN
50 mA/div
t - Time - 20 ms/div
Figure 48. Start Up into 20Ω Load, VOUT 2.5V
t - Time - 10 ms/div
Figure 47. Load Transient Response 5mA to 150mA,
Forced PWM Mode, VOUT 1.8V
18
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)
1m
TPS62231
MODE = GND,
Ref Lvl = 1mV
RBW 30kHz
EN 2 V/div
900m
V
= 1.8 V,
VBW 30kHz
SWT ´115ms
800m
OUT
R
LOAD = 12R
L = 2.2 mH,
(MIPSZ2012 2R2, Size 2012)
700m
600m
V
= 1.8 V
V
Pre Bias = 1V
C
= 4.7 mF (Size 0402)
OUT
OUT
1 V/div
OUT
VIN = 2.7V(green)
VIN = 3V(red)
500m
400m
300m
200m
SW 5 V/div
V
= 3.6 V
IN
C
= 4.7 mF
OUT
L = 2.2 mH
MODE = GND
= 0 mA
VIN = 3.6V(blue)
IL
200 mA/div
I
OUT
VIN = 4.2V(yellow)
100m
10n
Time Base - 20 ms/div
Start
0 Hz
4 MHz
f - Frequency
Stop
40 MHz
Figure 49. Startup in 1V Pre-biased Output
Figure 50. Spurious Output Noise, 12R Load,
TPS62231-Q1
1m
TPS62231
MODE = GND,
Ref Lvl = 1mV
900m
RBW 30kHz
VBW 30kHz
SWT 28ms
V
= 1.8 V,
OUT
R
LOAD = 100R
800m
700m
600m
L = 2.2 mH,
(MIPSZ2012 2R2, Size 2012)
C
= 4.7 mF (Size 0402)
OUT
VIN = 4.2V(yellow)
500m
400m
300m
200m
VIN = 3.6V(blue)
VIN = 3V(red)
VIN = 2.7V(green)
100m
10n
Start
0 Hz
1 MHz
Stop
10 MHz
f - Frequency
Figure 51. Spurious Output Noise, 100R Load, TPS62231-Q1
Copyright © 2011, Texas Instruments Incorporated
19
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
DETAILED DESCRIPTION
The TPS6223x-Q1 synchronous step down converter family includes a unique hysteretic PWM controller scheme
which enables switch frequencies over 3MHz, excellent transient and AC load regulation as well as operation
with cost competitive external components.
The controller topology supports forced PWM Mode as well as Power Save Mode operation. Power Save Mode
operation reduces the quiescent current consumption down to 22 μA and ensures high conversion efficiency at
light loads by skipping switch pulses. In forced PWM Mode, the device operates on a quasi fixed frequency,
avoids pulse skipping, and allows filtering of the switch noise by external filter components.
The TPS6223x-Q1 devices offer fixed output voltage options featuring smallest solution size by using only three
external components.
The internal switch current limit of typical 850 mA supports output currents of up to 500 mA, depending on the
operating condition.
A significant advantage of TPS6223x-Q1 compared to other hysteretic PWM controller topologies is its excellent
DC and AC load regulation capability in combination with low output voltage ripple over the entire load range
which makes this part well suited for audio and RF applications.
OPERATION
Once the output voltage falls below the threshold of the error comparator, a switch pulse is initiated, and the high
side switch is turned on. It remains turned on until a minimum on time of tONmin expires and the output voltage
trips the threshold of the error comparator or the inductor current reaches the high side switch current limit. Once
the high side switch turns off, the low side switch rectifier is turned on and the inductor current ramps down until
the high side switch turns on again or the inductor current reaches zero.
In forced PWM Mode operation, negative inductor current is allowed to enable continuous conduction mode even
at no load condition.
POWER SAVE MODE
Connecting the MODE pin to GND enables the automatic PWM and power-save mode operation. The converter
operates in quasi fixed frequency PWM mode at moderate to heavy loads and in the PFM (Pulse Frequency
Modulation) mode during light loads, which maintains high efficiency over a wide load current range. In PFM
Mode, the device starts to skip switch pulses and generates only single pulses with an on time of tONmin. The
PFM Mode frequency depends on the load current and the external inductor and output capacitor values. The
PFM Mode of TPS6223x-Q1 is optimized for low output voltage ripple if small external components are used.
Even at low output currents, the PFM frequency is above the audible noise spectrum and makes this operation
mode suitable for audio applications.
The on time tONmin can be estimated to:
VOUT
tONmin
=
´ 260 ns
V
IN
(1)
Therefore, the peak inductor current in PFM mode is approximately:
(V - VOUT
IN
)
ILPFMpeak
=
´ tONmin
L
(2)
(3)
The transition from PFM into PWM mode and vice versa can be estimated to:
IOUT_PFM/PWM = 0.5 x ILPFMpeak
With
tON: High side switch on time [ns]
VIN: Input voltage [V]
VOUT: Output voltage [V]
L : Inductance [μH]
ILPFMpeak : PFM inductor peak current [mA]
IOUT_PFM/PWM : Output current for PFM to PWM mode transition and vice versa [mA]
20
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
FORCED PWM MODE
Pulling the MODE pin high forces the converter to operate in a continuous conduction PWM mode even at light
load currents. The advantage is that the converter operates with a quasi fixed frequency that allows simple
filtering of the switching frequency for noise-sensitive applications. In this mode, the efficiency is lower compared
to the power-save mode during light loads.
For additional flexibility, it is possible to switch from power-save mode to forced PWM mode during operation.
This allows efficient power management by adjusting the operation of the converter to the specific system
requirements.
100% DUTY CYCLE LOW DROPOUT OPERATION
The device starts to enter 100% duty cycle mode once the input voltage comes close to the nominal output
voltage. In order to maintain the output voltage, the High Side switch is turned on 100% for one or more cycles.
With further decreasing VIN the High Side MOSFET switch is turned on completely. In this case the converter
offers a low input-to-output voltage difference. This is particularly useful in battery-powered applications to
achieve longest operation time by taking full advantage of the whole battery voltage range.
The minimum input voltage to maintain regulation depends on the load current and output voltage, and can be
calculated as:
V min = VOUTmax + IOUTmax ´
IN
RDS(on)max+ RL
(
)
(4)
With:
IOUTmax = maximum output current plus inductor ripple current
RDS(on)max = maximum P-channel switch RDSon.
RL = DC resistance of the inductor
VOUTmax = nominal output voltage plus maximum output voltage tolerance
UNDER VOLTAGE LOCKOUT
The under voltage lockout circuit prevents the device from misoperation at low input voltages. It prevents the
converter from turning on the switch or rectifier MOSFET under undefined conditions. The TPS6223x-Q1 devices
have a UVLO threshold set to 1.8V (typical). Fully functional operation is permitted for input voltage down to the
falling UVLO threshold level. The converter starts operation again once the input voltage trips the rising UVLO
threshold level.
SOFT START
The TPS6223x-Q1 has an internal soft-start circuit that controls the ramp up of the output voltage and limits the
inrush current during start-up. This limits input voltage drops when a battery or a high-impedance power source
is connected to the input of the converter.
The soft-start system generates a monotonic ramp up of the output voltage and reaches the nominal output
voltage typically 100μs after EN pin was pulled high.
Should the output voltage not have reached its target value by this time, such as in the case of heavy load, the
converter then operates in a current limit mode set by its switch current limits.
TPS6223x-Q1 is able to start into a pre-biased output capacitor. The converter starts with the applied bias
voltage and ramps the output voltage to its nominal value.
ENABLE / SHUTDOWN
The device starts operation when EN is set high and starts up with the soft start as previously described. For
proper operation, the EN pin must be terminated and must not be left floating.
Pulling the EN pin low forces the device into shutdown, with a shutdown quiescent current of typically 0.1 μA. In
this mode, the P and N-channel MOSFETs are turned off, the internal resistor feedback divider is disconnected,
and the entire internal-control circuitry is switched off.
Copyright © 2011, Texas Instruments Incorporated
21
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
The EN input can be used to control power sequencing in a system with various DC/DC converters. The EN pin
can be connected to the output of another converter, to drive the EN pin high and getting a sequencing of supply
rails.
SHORT-CIRCUIT PROTECTION
The TPS6223x-Q1 integrates a High Side and Low Side MOSFET current limit to protect the device against
heavy load or short circuit. The current in the switches is monitored by current limit comparators. When the
current in the P-channel MOSFET reaches its current limit, the P-channel MOSFET is turned off and the
N-channel MOSFET is turned on to ramp down the current in the inductor. The High Side MOSFET switch can
only turn on again, once the current in the Low Side MOSFET switch has decreased below the threshold of its
current limit comparator.
THERMAL SHUTDOWN
As soon as the junction temperature, TJ, exceeds 150°C (typical) the device goes into thermal shutdown. In this
mode, the High Side and Low Side MOSFETs are turned-off. The device continues its operation when the
junction temperature falls below the thermal shutdown hysteresis.
22
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
APPLICATION INFORMATION
L
V
IN
TPS62231
1/2.2 mH
2.05 V - 6 V
V
OUT
SW
FB
VIN
EN
1.8 V
C
C
IN
OUT
GND
2.2 mF
MODE
4.7 mF
Figure 52. TPS62231 1.8V Output
OUTPUT FILTER DESIGN (INDUCTOR AND OUTPUT CAPACITOR)
The TPS6223x-Q1 is optimized to operate with effective inductance values in the range of 0.7 μH to 4.3 μH and
with effective output capacitance in the range of 2 μF to 15 μF. The internal compensation is optimized to
operate with an output filter of L = 1 μH/2.2 μH and COUT = 4.7 μF. Larger or smaller inductor/capacitor values
can be used to optimize the performance of the device for specific operation conditions. For more details, see the
CHECKING LOOP STABILITY section.
INDUCTOR SELECTION
The inductor value affects its peak-to-peak ripple current, the PWM-to-PFM transition point, the output voltage
ripple and the efficiency. The selected inductor has to be rated for its dc resistance and saturation current. The
inductor ripple current (ΔIL) decreases with higher inductance and increases with higher VI N or VO UT. Equation 5
calculates the maximum inductor current under static load conditions. The saturation current of the inductor
should be rated higher than the maximum inductor current as calculated with Equation 6. This is recommended
because during heavy load transient the inductor current will rise above the calculated value.
Vout
1-
Vin
DIL = Vout ´
L ´ ¦
(5)
DI
L
I
= I
+
Lmax
outmax
2
(6)
With:
f = Switching Frequency
L = Inductor Value
ΔIL= Peak to Peak inductor ripple current
ILmax = Maximum Inductor current
In high-frequency converter applications, the efficiency is essentially affected by the inductor AC resistance (i.e.,
quality factor) and to a smaller extent by the inductor DCR value. To achieve high efficiency operation, care
should be taken in selecting inductors featuring a quality factor above 25 at the switching frequency. Increasing
the inductor value produces lower RMS currents, but degrades transient response. For a given physical inductor
size, increased inductance usually results in an inductor with lower saturation current.
The total losses of the coil consist of both the losses in the DC resistance, R(DC), and the following
frequency-dependent components:
•
•
•
•
The losses in the core material (magnetic hysteresis loss, especially at high switching frequencies)
Additional losses in the conductor from the skin effect (current displacement at high frequencies)
Magnetic field losses of the neighboring windings (proximity effect)
Radiation losses
The following inductor series from different suppliers have been used with the TPS6223x-Q1 converters.
Copyright © 2011, Texas Instruments Incorporated
23
TPS62231-Q1
TPS622314-Q1
SLVSB63 –DECEMBER 2011
www.ti.com
Table 1. List of inductors
INDUCTANCE
DIMENSIONS
INDUCTOR TYPE
SUPPLIER
[μH]
1.0/2.2
2.2
[mm3]
2.5 × 2.0 × 1.2
2.0 × 1.2 × 0.55
2.0 × 1.2 × 1.0
2.0 × 2.5 × 1.2
2.0 × 1.2 × 1.0
LQM2HPN1R0MJ0
LQM21PN2R2
MIPSZ2012
Murata
Murata
1.0/2.2
1.0/2.2
1.0/2.2
FDK
MIPSA2520
FDK
KSLI2012 series
Hitachi Metal
OUTPUT CAPACITOR SELECTION
The unique hysteretic PWM control scheme of the TPS62230 allows the use of tiny ceramic capacitors. Ceramic
capacitors with low ESR values have the lowest output voltage ripple and are recommended. The output
capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric capacitors, aside from their wide
variation in capacitance over temperature, become resistive at high frequencies.
At light load currents the converter operate in Power Save Mode and the output voltage ripple is dependent on
the output capacitor value and the PFM peak inductor current. Higher output capacitor values minimize the
voltage ripple in PFM Mode and tighten DC output accuracy in PFM Mode.
INPUT CAPACITOR SELECTION
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes. For most applications a 2.2 μF to 4.7 μF ceramic capacitor is recommended. The input capacitor
can be increased without any limit for better input voltage filtering. Because ceramic capacitor loses up to 80% of
its initial capacitance at 5 V, it is recommended to use 4.7 μF input capacitors for input voltages > 4.5 V.
Take care when using only small ceramic input capacitors. When a ceramic capacitor is used at the input and the
power is being supplied through long wires, such as from a wall adapter, a load step at the output or VIN step on
the input can induce ringing at the VIN pin. This ringing can couple to the output and be mistaken as loop
instability or could even damage the part by exceeding the maximum ratings.
Table 2 shows a list of tested input/output capacitors.
Table 2. List of Capacitor
CAPACITANCE [μF]
SIZE
0402
0402
0402
0402
0603
CAPACITOR TYPE
GRM155R60J225
AMK105BJ475MV
GRM155R60J475
CL05A475MQ5NRNC
GRM188R60J475
SUPPLIER
Murata
2.2
4.7
4.7
4.7
4.7
Taiyo Yuden
Murata
Samsung
Murata
CHECKING LOOP STABILITY
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signals:
•
•
•
Switching node, SW
Inductor current, IL
Output ripple voltage, VOUT(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations, the
regulation loop may be unstable. This is often a result of board layout and/or L-C combination.
As a next step in the evaluation of the regulation loop, the load transient response is tested. The time between
24
Copyright © 2011, Texas Instruments Incorporated
TPS62231-Q1
TPS622314-Q1
www.ti.com
SLVSB63 –DECEMBER 2011
the application of the load transient and the turn on of the P-channel MOSFET, the output capacitor must supply
all of the current required by the load. VOUT immediately shifts by an amount equal to ΔI(LOAD) x ESR, where ESR
is the effective series resistance of COUT. ΔI(LOAD) begins to charge or discharge CO generating a feedback error
signal used by the regulator to return VOUT to its steady-state value. The results are most easily interpreted when
the device operates in PWM mode.
During this recovery time, VOUT can be monitored for settling time, overshoot or ringing that helps judge the
converter’s stability. Without any ringing, the loop has usually more than 45° of phase margin.
Because the damping factor of the circuitry is directly related to several resistive parameters (e.g., MOSFET
rDS(on)) that are temperature dependant, the loop stability analysis has to be done over the input voltage range,
load current range, and temperature range.
LAYOUT CONSIDERATIONS
As for all switching power supplies, the layout is an important step in the design. Proper function of the device
demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If
the layout is not carefully done, the regulator could show poor line and/or load regulation, stability issues as well
as EMI problems. It is critical to provide a low inductance, impedance ground path. Therefore, use wide and
short traces for the main current paths. The input capacitor should be placed as close as possible to the IC pins
as well as the inductor and output capacitor.
Use a common Power GND node and a different node for the Signal GND to minimize the effects of ground
noise. Keep the common path to the GND PIN, which returns the small signal components and the high current
of the output capacitors as short as possible to avoid ground noise. The FB line should be connected to the
output capacitor and routed away from noisy components and traces (e.g. SW line).
Total area
L1
is less than
12mm²
V IN
C
1
C2
GND
VOUT
Figure 53. Recommended PCB Layout for TPS6223x-Q1
Copyright © 2011, Texas Instruments Incorporated
25
PACKAGE OPTION ADDENDUM
www.ti.com
26-Dec-2011
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS622314TDRYRQ1
TPS62231TDRYRQ1
ACTIVE
ACTIVE
SON
SON
DRY
DRY
6
6
5000
5000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS62231-Q1, TPS622314-Q1 :
Catalog: TPS62231, TPS622314
•
NOTE: Qualified Version Definitions:
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Dec-2011
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Dec-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS622314TDRYRQ1
TPS62231TDRYRQ1
SON
SON
DRY
DRY
6
6
5000
5000
179.0
179.0
8.4
8.4
1.2
1.2
1.65
1.65
0.7
0.7
4.0
4.0
8.0
8.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Dec-2011
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS622314TDRYRQ1
TPS62231TDRYRQ1
SON
SON
DRY
DRY
6
6
5000
5000
195.0
195.0
200.0
200.0
45.0
45.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明