TPS65023B [TI]
6 通道电源管理 IC (PMIC),具有 3 个直流/直流转换器、3 个 LDO、I2C 接口和 DVS;型号: | TPS65023B |
厂家: | TEXAS INSTRUMENTS |
描述: | 6 通道电源管理 IC (PMIC),具有 3 个直流/直流转换器、3 个 LDO、I2C 接口和 DVS 集成电源管理电路 电源电路 转换器 |
文件: | 总55页 (文件大小:1439K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
POWER MANAGEMENT IC FOR LI-ION POWERED SYSTEMS
Check for Samples: TPS65023, TPS65023B
1
FEATURES
DESCRIPTION
23
•
1.7 A, 90% Efficient Step-Down Converter for
The TPS65023, TPS65023B is an integrated Power
Management IC for applications powered by one
Li-Ion or Li-Polymer cell, and which require multiple
power rails. The TPS65023, TPS65023B provides
three highly efficient, step-down converters targeted
at providing the core voltage, peripheral, I/O and
memory rails in a processor based system. The core
converter allows for on-the-fly voltage changes via
serial interface, allowing the system to implement
dynamic power savings. All three step-down
converters enter a low-power mode at light load for
maximum efficiency across the widest possible range
of load currents. The TPS65023, TPS65023B also
integrates two general-purpose 200 mA LDO voltage
regulators, which are enabled with an external input
pin. Each LDO operates with an input voltage range
between 1.5 V and 6.5 V, allowing them to be
supplied from one of the step-down converters or
directly from the battery. The default output voltage of
the LDOs can be digitally set to 4 different voltage
combinations using the DEFLDO1 and DEFLDO2
pins. The serial interface can be used for dynamic
voltage scaling, masking interrupts, or for dis/enabling
and setting the LDO output voltages. The interface is
compatible with the Fast/Standard mode I2C
specification, allowing transfers at up to 400 kHz. The
TPS65023, TPS65023B is available in a 40-pin (RSB)
Processor Core (VDCDC1)
•
1.2 A, Up to 95% Efficient Step-Down
Converter for System Voltage (VDCDC2)
•
1.0 A, 92% Efficient Step-Down Converter for
Memory Voltage (VDCDC3)
•
•
•
30 mA LDO/Switch for Real Time Clock (VRTC)
2 × 200 mA General-Purpose LDO
Dynamic Voltage Management for Processor
Core
•
Preselectable LDO Voltage Using Two Digital
Input Pins
•
•
•
•
•
Externally Adjustable Reset Delay Time
Battery Backup Functionality
Separate Enable Pins for Inductive Converters
I2C™ Compatible Serial Interface
I2C™ Setup and Hold Timing:
–
–
TPS65023: 300ns
TPS65023B: 100ns
•
•
•
•
85-μA Quiescent Current
Low Ripple PFM Mode
Thermal Shutdown Protection
40 Pin, 5 mm × 5 mm QFN Package
QFN package, and operates over
a
free-air
temperature of –40°C to 85°C.
APPLICATIONS
•
•
•
•
•
Digital Media Players
Internet Audio Player
Digital Still Camera
Smart Phones
Supply DaVinci™ DSP Family Solutions
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
DaVinci, PowerPAD are trademarks of Texas Instruments.
I2C is a trademark of NXP Semiconductors.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2011, Texas Instruments Incorporated
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION(1)
TA
PACKAGE
PART NUMBER(2)
TPS65023RSB
–40°C to 85°C
–40°C to 85°C
40 pin QFN (RSB)
40 pin QFN (RSB)
TPS65023BRSB
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
(2) The RSB package is available in tape and reel. Add the R suffix (TPS65023RSBR, TPS65023BRSBR) to order quantities of 3000 parts
per reel. Add the T suffix (TPS65023RSBT; TPS65023BRSBT) to order quantities of 250 parts per reel.
ABSOLUTE MAXIMUM RATINGS(1)
over operating free-air temperature range (unless otherwise noted)
VALUE
UNIT
MIN
MAX
VI Input voltage range on all pins except AGND and PGND pins with respect to
AGND
–0.3
7
V
Current at VINDCDC1, L1, PGND1, VINDCDC2, L2, PGND2, VINDCDC3, L3,
PGND3
2000
1000
mA
mA
Peak current at all other pins
Continuous total power dissipation
TA Operating free-air temperature
TJ Maximum junction temperature
See Thermal Information Table
–40
85
°C
°C
°C
125
150
Ts Storage temperature
–65
tg
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability
THERMAL INFORMATION
TPS65023
THERMAL METRIC(1)
RSB
40 PINS
32.7
15.3
13.6
0.1
UNITS
θJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
θJCtop
θJB
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ψJB
5.4
θJCbot
1.1
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
2
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX UNIT
Input voltage range step-down converters
VCC
(VINDCDC1, VINDCDC2, VINDCDC3); pins need to be tied to the same
voltage rail
2.5
6
V
V
Output voltage range for VDCDC1 step-down converter(1)
Output voltage range for VDCDC2 step-down converter(1)
Output voltage range for VDCDC3 step-down converter(1)
Input voltage range for LDOs (VINLDO1, VINLDO2)
Output voltage range for LDOs (VLDO1, VLDO2)
Output current at L1
0.6
0.6
0.6
1.5
1
VINDCDC1
VINDCDC2
VINDCDC3
6.5
VO
VI
V
VO
VINLDO1-2
1700
V
IO(DCDC1)
mA
μH
μF
μF
mA
μH
μF
μF
mA
μH
μF
μF
μF
μF
μF
mA
μF
°C
°C
Ω
Inductor at L1(2)
1.5
10
10
2.2
22
(2)
CI(DCDC1)
CO(DCDC1)
IO(DCDC2)
Input capacitor at VINDCDC1
(2)
Output capacitor at VDCDC1
Output current at L2
1200
1000
(2)
Inductor at L2
1.5
10
10
2.2
22
(2)
CI(DCDC2)
CO(DCDC2)
IO(DCDC3)
Input capacitor at VINDCDC2
(2)
Output capacitor at VDCDC2
Output current at L3
(2)
Inductor at L3
1.5
10
10
1
2.2
22
CI(DCDC3)
CO(DCDC3)
CI(VCC)
Input capacitor at VINDCDC3(2)
(2)
Output capacitor at VDCDC3
(2)
Input capacitor at VCC
(2)
Ci(VINLDO)
CO(VLDO1-2)
IO(VLDO1-2)
CO(VRTC)
TA
Input capacitor at VINLDO
1
(2)
Output capacitor at VLDO1, VLDO2
2.2
Output current at VLDO1, VLDO2
200
(2)
Output capacitor at VRTC
4.7
–40
–40
Operating ambient temperature
85
125
10
TJ
Operating junction temperature
Resistor from VINDCDC3, VINDCDC2, VINDCDC1 to VCC used for filtering(3)
1
(1) When using an external resistor divider at DEFDCDC3, DEFDCDC2, DEFDCDC1
(2) See Applications Information section for more information.
(3) Up to 3 mA can flow into VCC when all 3 converters are running in PWM. This resistor causes the UVLO threshold to be shifted
accordingly.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP
MAX UNIT
CONTROL SIGNALS : SCLK, SDAT (input) for TPS65023
High level input voltage (except the SDAT
pin)
Resistor pullup at SCLK = 4.7kΩ, pulled to
VRTC
VIH
1.3
VCC
VCC
V
V
Resistor pullup at SDAT = 4.7kΩ, pulled to
VRTC
VIH
High level input voltage for the SDAT pin
1.45
Resistor pullup at SCLK and SDAT = 4.7kΩ,
pulled to VRTC
VIL
IH
Low level input voltage
Input bias current
0
0.4
0.1
V
0.01
μA
CONTROL SIGNALS : SCLK, SDAT (input) for TPS65023B
Rpullup at SCLK = 4.7 kΩ, pulled to VRTC;
For VCC = 2.5V to 5.25V
VIH
VIH
VIH
High level input voltage for the SCLK pin
High level input voltage for the SDAT pin
High level input voltage for the SDAT pin
1.4
1.69
1.55
VCC
VCC
VCC
V
V
V
Rpullup at SDAT = 4.7 kΩ, pulled to VRTC;
For VCC = 2.5V to 5.25V
Rpullup at SDAT = 4.7 kΩ, pulled to VRTC;
For VCC = 2.5V to 4.5V
Rpullup at SCLK and SDAT = 4.7 kΩ, pulled to
VRTC
VIL
IH
Low level input voltage
Input bias current
0
0.35
0.1
V
0.01
μA
CONTROL SIGNALS : HOT_RESET, DCDC1_EN, DCDC2_EN, DCDC3_EN, LDO_EN, DEFLDO1, DEFLDO2
VIH
High-level input voltage
Low-level input voltage
Input bias current
1.3
0
VCC
0.4
0.1
35
V
V
VIL
IIB
0.01
30
μA
ms
tdeglitch
Deglitch time at HOT_RESET
25
CONTROL SIGNALS : LOWBAT, PWRFAIL, RESPWRON, INT, SDAT (output)
VOH
VOL
High-level output voltage
6
V
V
Low-level output voltage
IIL = 5 mA
0
0.3
Duration of low pulse at RESPWRON
External capacitor 1 nF
used for generating RESPWRON delay
100
2
ms
μA
internal charge / discharge current on pin
TRESPWRON
1.7
2.3
ICONST
TRESPW internal lower comparator threshold on pin used for generating RESPWRON delay
0.225 0.25 0.275
V
V
RON_LO
WTH
TRESPWRON
TRESPW internal upper comparator threshold on pin used for generating RESPWRON delay
0.97
1
1.103
RON_UPT TRESPWRON
H
Resetpwron threshold
Resetpwron threshold
leakage current
VRTC falling
–3%
2.4
3%
3%
0.1
V
V
VRTC rising
–3% 2.52
ILK
output inactive high
μA
4
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
SUPPLY PINS: VCC, VINDCDC1, VINDCDC2, VINDCDC3
All 3 DCDC converters enabled, zero VCC = 3.6 V, VBACKUP = 3 V;
TEST CONDITIONS
MIN TYP MAX UNIT
85
78
100
90
load, and no switching, LDOs enabled V(VSYSIN) = 0 V
All 3 DCDC converters enabled, zero VCC = 3.6 V, VBACKUP = 3 V;
load, and no switching, LDOs off
V(VSYSIN) = 0 V
Operating quiescent
current, PFM
I(q)
μA
DCDC1 and DCDC2 converters
enabled, zero load, and no switching,
LDOs off
VCC = 3.6 V, VBACKUP = 3 V;
V(VSYSIN) = 0 V
57
70
DCDC1 converter enabled, zero load, VCC = 3.6 V, VBACKUP = 3 V;
43
2
55
3
and no switching, LDOs off
V(VSYSIN) = 0 V
All 3 DCDC converters enabled and
running in PWM, LDOs off
VCC = 3.6 V, VBACKUP = 3 V;
V(VSYSIN) = 0 V
DCDC1 and DCDC2 converters
Current into VCC; PWM enabled and running in PWM, LDOs
off
VCC = 3.6 V, VBACKUP = 3 V;
V(VSYSIN) = 0 V
II
1.5
2.5
mA
DCDC1 converter enabled and
running in PWM, LDOs off
VCC = 3.6 V, VBACKUP = 3 V;
V(VSYSIN) = 0 V
0.85
23
2
33
5
VCC = 3.6 V, VBACKUP = 3 V;
V(VSYSIN) = 0 V
μA
μA
μA
VCC = 2.6 V, VBACKUP = 3 V;
V(VSYSIN) = 0 V
I(q)
Quiescent current
All converters disabled, LDOs off
3.5
VCC = 3.6 V, VBACKUP = 0 V;
V(VSYSIN) = 0 V
43
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY PINS: VBACKUP, VSYSIN, VRTC
VBACKUP = 3 V, VSYSIN = 0 V;
VCC = 2.6 V, current into VBACKUP
I(q)
Operating quiescent current
Operating quiescent current
20
33
3
μA
μA
VBACKUP < V_VBACKUP, current into
VBACKUP
I(SD)
2
3
VRTC LDO output voltage
Output current for VRTC
VSYSIN = VBACKUP = 0 V, IO = 0 mA
VSYSIN < 2.57 V and VBACKUP < 2.57 V
VRTC = GND; VSYSIN = VBACKUP = 0 V
V
IO
30
mA
mA
VRTC short-circuit current limit
100
Maximum output current at VRTC for
RESPWRON = 1
VRTC > 2.6 V, VCC = 3 V;
VSYSIN = VBACKUP = 0 V
30
mA
VO
Output voltage accuracy for VRTC
Line regulation for VRTC
VSYSIN = VBACKUP = 0 V; IO = 0 mA
VCC = VRTC + 0.5 V to 6.5 V, IO = 5 mA
–1%
–1%
1%
1%
IO = 1 mA to 30 mA;
VSYSIN = VBACKUP = 0 V
Load regulation VRTC
–3%
1%
Regulation time for VRTC
Input leakage current at VSYSIN
rDS(on) of VSYSIN switch
rDS(on) of VBACKUP switch
Input voltage range at VBACKUP(1)
Input voltage range at VSYSIN(1)
VSYSIN threshold
Load change from 10% to 90%
10
μs
μA
Ω
Ω
V
Ilkg
VSYSIN < V_VSYSIN
2
12.5
12.5
3.75
3.75
3%
2.73
2.73
–3%
–3%
–3%
–3%
V
VSYSIN falling
VSYSIN rising
2.55
2.65
2.55
2.65
V
VSYSIN threshold
3%
V
VBACKUP threshold
VBACKUP falling
VBACKUP rising
3%
V
VBACKUP threshold
3%
V
SUPPLY PIN: VINLDO
Operating quiescent current
Current per LDO into VINLDO
for LDO_CTRL = 0x0
I(q)
16
30
1
μA
μA
Total current for both LDOs into VINLDO,
VLDO = 0 V
I(SD)
Shutdown current
0.1
(1) Based on the requirements for the Intel PXA270 processor.
6
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
VDCDC1 STEP-DOWN CONVERTER
VI
Input voltage range, VINDCDC1
Maximum output current
2.5
6
V
IO
1700
mA
μA
mΩ
μA
mΩ
μA
I(SD)
rDS(on)
Ilkg
Shutdown supply current in VINDCDC1
P-channel MOSFET on-resistance
P-channel leakage current
DCDC1_EN = GND
0.1
1
261
2
VINDCDC1 = V(GS) = 3.6 V
VINDCDC1 = 6 V
125
rDS(on)
Ilkg
N-channel MOSFET on-resistance
N-channel leakage current
VINDCDC1 = V(GS) = 3.6 V
V(DS) = 6 V
130
7
260
10
Forward current limit (P-channel and
N-channel)
2.5 V < VI(MAIN) < 6 V
1.94
1.95
–2
2.19
2.25
2.44
2.55
2
A
fS
Oscillator frequency
Fixed output voltage
MHz
VINDCDC1 = 2.5 V to 6 V;
0 mA ≤ IO ≤ 1.7 A
FPWMDCDC1=0
All VDCDC1
%
Fixed output voltage
VINDCDC1 = 2.5 V to 6 V;
0 mA ≤ IO ≤ 1.7 A
–1
–2
–1
1
2
1
FPWMDCDC1=1
Adjustable output voltage with resistor divider VINDCDC1 = VDCDC1 + 0.5 V (min 2.5 V)
at DEFDCDC1; FPWMDCDC1=0 to 6 V; 0 mA ≤ IO ≤ 1.7 A
%
%
Adjustable output voltage with resistor divider VINDCDC1 = VDCDC1 + 0.5 V (min 2.5 V)
at DEFDCDC1; FPWMDCDC1=1
to 6 V; 0 mA ≤ IO ≤ 1.7 A
VINDCDC1 = VDCDC1 + 0.3 V (min. 2.5 V)
to 6 V; IO = 10 mA
Line Regulation
0
%/V
Load Regulation
IO = 10 mA to 1700 mA
0.25
175
750
1
%/A
μs
tStart
Start-up time
Time from active EN to start switching
Time to ramp from 5% to 95% of VOUT
145
400
200
tRamp
VOUT ramp-up time
1000
μs
Internal resistance from L1 to GND
VDCDC1 discharge resistance
MΩ
Ω
DCDC1 discharge = 1
300
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
VDCDC2 STEP-DOWN CONVERTER
VI
Input voltage range, VINDCDC2
2.5
6
V
DEFDCDC2 = GND
1200
IO
Maximum output current
mA
VINDCDC2 = 3.6 V;
3.3 V - 1% ≤ VDCDC2 ≤ 3.3V + 1%
1000
I(SD)
rDS(on)
Ilkg
Shutdown supply current in VINDCDC2
P-channel MOSFET on-resistance
P-channel leakage current
DCDC2_EN = GND
VINDCDC2 = V(GS) = 3.6 V
VINDCDC2 = 6 V
0.1
1
300
2
μA
mΩ
μA
140
rDS(on)
Ilkg
N-channel MOSFET on-resistance
N-channel leakage current
VINDCDC2 = V(GS) = 3.6 V
V(DS) = 6 V
150
7
297
10
mΩ
μA
Forward current limit (P-channel and
N-channel)
ILIMF
fS
2.5 V < VINDCDC2 < 6 V
1.74
1.95
–2
1.94
2.25
2.12
2.55
2
A
Oscillator frequency
MHz
VINDCDC2 = 2.5 V to 6 V;
0 mA ≤ IO ≤ 1.2 A
VDCDC2 = 1.8 V
Fixed output voltage
%
%
FPWMDCDC2=0
VINDCDC2 = 3.7 V to 6 V;
0 mA ≤ IO ≤ 1.2 A
VDCDC2 = 3.3 V
–1
–2
1
2
VINDCDC2 = 2.5 V to 6 V;
0 mA ≤ IO ≤ 1.2 A
VDCDC2 = 1.8 V
Fixed output voltage
FPWMDCDC2=1
VINDCDC2 = 3.7 V to 6 V;
0 mA ≤ IO ≤ 1.2 A
VDCDC2 = 3.3 V
–1
1
Adjustable output voltage with resistor
divider at DEFDCDC2 FPWMDCDC2=0
VINDCDC2 = VDCDC2 + 0.3 V (min 2.5 V) to 6
V; 0 mA ≤ IO ≤ 1 A
–2%
–1%
2%
1%
Adjustable output voltage with resistor
divider at DEFDCDC2; FPWMDCDC2=1
VINDCDC2 = VDCDC2 + 0.3 V (min 2.5 V) to 6
V; 0 mA ≤ IO ≤ 1 A
VINDCDC2 = VDCDC2 + 0.3 V (min. 2.5 V) to 6
V; IO = 10 mA
Line Regulation
0
%/V
Load Regulation
IO = 10 mA to 1000 mA
0.25
175
750
1
%/A
µs
tStart
Start-up time
Time from active EN to start switching
Time to ramp from 5% to 95% of VOUT
145
400
200
tRamp
VOUT ramp-up time
1000
μs
Internal resistance from L2 to GND
VDCDC2 discharge resistance
MΩ
Ω
DCDC2 discharge =1
300
8
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
VDCDC3 STEP-DOWN CONVERTER
VI
Input voltage range, VINDCDC3
2.5
6
V
DEFDCDC3 = GND
1000
IO
Maximum output current
mA
VINDCDC3 = 3.6 V;
3.3V - 1% ≤ VDCDC3 ≤ 3.3V + 1%
525
I(SD)
rDS(on)
Ilkg
Shutdown supply current in VINDCDC3
P-channel MOSFET on-resistance
P-channel leakage current
DCDC3_EN = GND
VINDCDC3 = V(GS) = 3.6 V
VINDCDC3 = 6 V
0.1
310
0.1
220
7
1
698
2
μA
mΩ
μA
rDS(on)
Ilkg
N-channel MOSFET on-resistance
N-channel leakage current
VINDCDC3 = V(GS) = 3.6 V
V(DS) = 6 V
503
10
mΩ
μA
Forward current limit (P-channel and
N-channel)
2.5 V < VINDCDC3 < 6 V
1.28
1.95
–2
1.49
2.25
1.69
2.55
2
A
fS
Oscillator frequency
MHz
VINDCDC3 = 2.5 V to 6 V;
0 mA ≤ IO ≤ 1 A
VDCDC3 = 1.8V
Fixed output voltage
%
%
FPWMDCDC3=0
VINDCDC3 = 3.6 V to 6 V;
0 mA ≤ IO ≤ 1 A
VDCDC3 = 3.3V
–1
–2
1
2
VINDCDC3 = 2.5 V to 6 V;
0 mA ≤ IO ≤ 1 A
VDCDC3 = 1.8V
Fixed output voltage
FPWMDCDC3=1
VINDCDC3 = 3.6 V to 6 V;
0 mA ≤ IO ≤ 1 A
VDCDC3 = 3.3V
–1
1
Adjustable output voltage with resistor
divider at DEFDCDC3 FPWMDCDC3=0
VINDCDC3 = VDCDC3 + 0.5 V (min 2.5 V) to 6
V; 0 mA ≤ IO ≤ 800 mA
–2%
–1%
2%
1%
Adjustable output voltage with resistor
divider at DEFDCDC3; FPWMDCDC3=1
VINDCDC3 = VDCDC3 + 0.5 V (min 2.5 V) to 6
V; 0 mA ≤ IO ≤ 800 mA
VINDCDC3 = VDCDC3 + 0.3 V (min. 2.5 V) to 6
V; IO = 10 mA
Line Regulation
0
%/V
Load Regulation
IO = 10 mA to 1000 mA
0.25
175
750
1
%/A
µs
tStart
Start-up time
Time from active EN to start switching
Time to ramp from 5% to 95% of VOUT
145
400
200
tRamp
VOUT ramp-up time
1000
μs
Internal resistance from L3 to GND
VDCDC3 discharge resistance
MΩ
Ω
DCDC3 discharge =1
300
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are
at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
VLDO1 and VLDO2 LOW DROPOUT REGULATORS
VI
Input voltage range for LDO1, 2
LDO1 output voltage range
LDO2 output voltage range
1.5
1
6.5
3.15
3.3
V
V
V
VO(LD01)
VO(LDO2)
1
VI = 1.8 V, VO = 1.3 V
200
IO
Maximum output current for LDO1, LDO2
LDO1 and LDO2 short circuit current limit
mA
mA
VI = 1.5 V, VO = 1.3 V
120
65
I(SC)
V(LDO1) = GND, V(LDO2) = GND
IO = 50 mA, VINLDO = 1.8 V
IO = 50 mA, VINLDO = 1.5 V
IO = 200 mA, VINLDO = 1.8 V
IO = 10 mA
400
120
150
300
1%
Minimum voltage drop at LDO1, LDO2
mV
Output voltage accuracy for LDO1, LDO2
Line regulation for LDO1, LDO2
–2%
–1%
–1%
VINLDO1, 2 = VLDO1,2 + 0.5 V
(min. 2.5 V) to 6.5 V, IO = 10 mA
1%
1%
Load regulation for LDO1, LDO2
Regulation time for LDO1, LDO2
IO = 0 mA to 50 mA
Load change from 10% to 90%
10
μs
ANALOGIC SIGNALS DEFDCDC1, DEFDCDC2, DEFDCDC3
VIH
VIL
High-level input voltage
Low-level input voltage
Input bias current
1.3
0
VCC
0.1
V
V
0.001
0.05
μA
THERMAL SHUTDOWN
T(SD) Thermal shutdown
Thermal shutdown hysteresis
INTERNAL UNDERVOLTAGE LOCK OUT
Increasing junction temperature
Decreasing junction temperature
160
20
°C
°C
UVLO
Internal UVLO
VCC falling
–2%
2.35
120
2%
1%
V
V(UVLO_HYST
)
Internal UVLO comparator hysteresis
mV
VOLTAGE DETECTOR COMPARATORS
Comparator threshold
(PWRFAIL_SNS, LOWBAT_SNS)
Falling threshold
25-mV overdrive
–1%
1
V
Hysteresis
Propagation delay
POWER GOOD
40
50
60
10
mV
μs
VDCDC1, VDCDC2, VDCDC3, VLDO1,
VLDO2, decreasing
V(PGOODF)
V(PGOODR)
–12%
–7%
–10%
–5%
–8%
–3%
VDCDC1, VDCDC2, VDCDC3, VLDO1,
VLDO2, increasing
10
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
PIN ASSIGNMENT
(TOP VIEW)
40 39 38 37 36 35 34 33 32 31
30
29
28
27
SCLK
1
2
DEFDCDC3
VDCDC3
PGND3
SDAT
INT
3
4
5
6
7
8
9
RESPWRON
TRESPWRON
DCDC1_EN
DCDC2_EN
DCDC3_EN
LDO_EN
LOWBAT
L3
26
25
VINDCDC3
VINDCDC1
L1
24
23
22
21
PGND1
VDCDC1
DEFDCDC1
10
11 12 13 14 15 16 17 18 19 20
PIN FUNCTIONS
PIN
I/O
DESCRIPTION
NAME
NO.
SWITCHING REGULATOR SECTION
AGND1
40
17
–
Analog ground. All analog ground pins are connected internally on the chip.
Analog ground. All analog ground pins are connected internally on the chip.
Connect the power pad to analog ground.
AGND2
PowerPAD™
Input voltage for VDCDC1 step-down converter. VINDCDC1 must be connected to the same voltage
supply as VINDCDC2, VINDCDC3, and VCC.
VINDCDC1
6
I
I
I
I
I
I
L1
7
9
8
Switch pin of VDCDC1 converter. The VDCDC1 inductor is connected here.
VDCDC1 feedback voltage sense input. Connect directly to VDCDC1
Power ground for VDCDC1 converter.
VDCDC1
PGND1
Input voltage for VDCDC2 step-down converter. VINDCDC2 must be connected to the same voltage
supply as VINDCDC1, VINDCDC3, and VCC.
VINDCDC2
36
L2
35
33
34
Switch pin of VDCDC2 converter. The VDCDC2 inductor is connected here.
VDCDC2 feedback voltage sense input. Connect directly to VDCDC2
Power ground for VDCDC2 converter
VDCDC2
PGND2
Input voltage for VDCDC3 step-down converter. VINDCDC3 must be connected to the same voltage
supply as VINDCDC1, VINDCDC2, and VCC.
VINDCDC3
5
L3
4
2
3
Switch pin of VDCDC3 converter. The VDCDC3 inductor is connected here.
VDCDC3 feedback voltage sense input. Connect directly to VDCDC3
Power ground for VDCDC3 converter.
VDCDC3
PGND3
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
PIN FUNCTIONS (continued)
PIN
I/O
DESCRIPTION
NAME
NO.
Power supply for digital and analog circuitry of VDCDC1, VDCDC2, and VDCDC3 dc-dc converters.
VCC must be connected to the same voltage supply as VINDCDC3, VINDCDC1, and VINDCDC2.
VCC also supplies serial interface block.
VCC
37
I
I
I
I
Input signal indicating default VDCDC1 voltage, 0 = 1.2 V, 1 = 1.6 V DEFDCDC1 can also be
connected to a resistor divider between VDCDC1 and GND, if the output voltage of the DCDC1
converter is set in a range from 0.6 V to VINDCDC1 V.
DEFDCDC1
DEFDCDC2
DEFDCDC3
10
32
1
Input signal indicating default VDCDC2 voltage, 0 = 1.8 V, 1 = 3.3 V DEFDCDC2 can also be
connected to a resistor divider between VDCDC2 and GND, if the output voltage of the DCDC2
converter is set in a range from 0.6 V to VINDCDC2 V.
Input signal indicating default VDCDC3 voltage, 0 = 1.8 V, 1 = 3.3 V DEFDCDC3 can also be
connected to a resistor divider between VDCDC3 and GND, if the output voltage of the DCDC3
converter is set in a range from 0.6 V to VINDCDC3 V.
DCDC1_EN
DCDC2_EN
DCDC3_EN
25
24
23
I
I
I
VDCDC1 enable pin. A logic high enables the regulator, a logic low disables the regulator.
VDCDC2 enable pin. A logic high enables the regulator, a logic low disables the regulator.
VDCDC3 enable pin. A logic high enables the regulator, a logic low disables the regulator.
LDO REGULATOR SECTION
VINLDO
VLDO1
19
20
18
22
15
16
14
12
13
I
O
O
I
Input voltage for LDO1 and LDO2
Output voltage of LDO1
VLDO2
Output voltage of LDO2
LDO_EN
VBACKUP
VRTC
Enable input for LDO1 and LDO2. A Logic high enables the LDOs, a logic low disables the LDOs.
Connect the backup battery to this input pin.
I
O
I
Output voltage of the LDO/switch for the real time clock.
Input of system voltage for VRTC switch.
VSYSIN
DEFLD01
DEFLD02
I
Digital input. DEFLD01 sets the default output voltage of LDO1 and LDO2.
Digital input. DEFLD02 sets the default output voltage of LDO1 and LDO2.
I
CONTROL AND I2C SECTION
HOT_RESET
TRESPWRON
RESPWRON
PWRFAIL
LOW_BAT
INT
11
26
27
31
21
28
30
29
38
39
I
I
Push button input that reboots or wakes up the processor via RESPWRON output pin.
Connect the timing capacitor to TRESPWRON to set the reset delay time: 1 nF → 100 ms.
Open drain system reset output.
O
O
O
O
I
Open drain output. Active low when PWRFAIL comparator indicates low VBAT condition.
Open drain output of LOW_BAT comparator.
Open drain output
SCLK
Serial interface clock line
SDAT
I/O
I
Serial interface data/address
PWRFAIL_SNS
LOWBAT_SNS
Input for the comparator driving the PWRFAIL output.
Input for the comparator driving the LOW_BAT output.
I
12
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
FUNCTIONAL BLOCK DIAGRAM FOR TPS65023 AND TPS65023B
TPS65023, TPS65023B
V
CC
VSYSIN
VBACKUP
VRTC
BBAT
SWITCH
Thermal
Shutdown
VINDCDC1
L1
DCDC1
Buck Converter
1700 mA
VDCDC1
DEFDCDC1
PGND1
SCLK
SDAT
Serial Interface
VINDCDC2
L2
DCDC1_EN
DCDC2_EN
DCDC3_EN
LDO_EN
DCDC2
Buck Converter
1200 mA
VDCDC2
DEFDCDC2
PGND2
CONTROL
HOT_RESET
RESPWRON
INT
Dynamic
Voltage
Management
VINDCDC3
L3
LOWBAT_SNS
PWRFAIL_SNS
LOW_BATT
DCDC3
Buck Converter
1000 mA
VDCDC3
DEFDCDC3
PGND3
UVLO
VREF
OSC
PWRFAIL
TRESPWRON
LDO1
200 mA
VLDO1
VINLDO
VLDO2
DEFLDO1
DEFLDO2
LDO2
200 mA
AGND1
AGND2
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS
Graphs were taken using the EVM with the following inductor/output capacitor combinations:
CONVERTER
VDCDC1
INDUCTOR
VLCF4020-2R2
OUTPUT CAPACITOR
C2012X5R0J106M
C2012X5R0J106M
C2012X5R0J106M
OUTPUT CAPACITOR VALUE
2 × 10 μF
2 × 10 μF
2 × 10 μF
VDCDC2
VLCF4020-2R2
VDCDC3
VLF4012AT-2R2M1R5
Table 1. Table of Graphs
FIGURE
η
Efficiency
Output voltage
vs Output current
1, 2, 3, 4, 5, 6
vs Output current at 85°C
7, 8
9, 10, 11
12, 13, 14
15
Line transient response
Load transient response
VDCDC2 PFM operation
VDCDC2 low ripple PFM operation
VDCDC2 PWM operation
16
17
Startup VDCDC1, VDCDC2 and VDCDC3
Startup LDO1 and LDO2
18
19
Line transient response
20, 21, 22
23, 24, 25
Load transient response
DCDC1: EFFICIENCY
vs
DCDC1: EFFICIENCY
vs
OUTPUT CURRENT
OUTPUT CURRENT
100
90
100
90
80
70
60
50
40
T
= 25°C
= 1.2 V
A
V = 2.5 V
I
V
O
V = 3.6 V
PWM Mode
I
V = 2.5 V
I
80
70
V = 3.6 V
I
V = 4.2 V
I
60
50
40
30
V = 5 V
I
V = 4.2 V
I
30
20
T
= 25°C
= 1.2 V
20
10
0
A
V = 5 V
V
I
O
10
0
PWM/PFM Mode
0.01
0.1
1
10
100 1 k
10 k
0.01
0.1
1
10
100
1 k
10 k
I
- Output Current - mA
I
- Output Current - mA
O
O
Figure 1.
Figure 2.
14
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
DCDC2: EFFICIENCY
vs
DCDC2: EFFICIENCY
vs
OUTPUT CURRENT
OUTPUT CURRENT
100
90
80
70
60
50
40
100
90
80
70
60
50
40
V = 2.5 V
I
T
= 25°C
V = 2.5 V
A
I
V = 3.6 V
I
V
= 1.8 V
O
PWM Mode
V = 3.6 V
I
V = 4.2 V
I
V = 5 V
I
V = 4.2 V
I
30
20
30
20
V = 5 V
I
T
= 25°C
A
V
= 1.8 V
O
10
0
10
0
PWM/PFM Mode
0.01
0.1
1
10
100 1 k
10 k
0.01
0.1
1
10
100
1 k
10 k
I
- Output Current - mA
I
- Output Current - mA
O
O
Figure 3.
Figure 4.
DCDC3: EFFICIENCY
vs
DCDC3: EFFICIENCY
vs
OUTPUT CURRENT
OUTPUT CURRENT
100
100
90
80
70
60
50
40
V = 2.5 V
I
V = 2.5 V
I
T
= 25°C
A
90 V = 3.6 V
I
V
= 1.8 V
O
PWM Mode
80
70
60
V = 3.6 V
I
V = 4.2 V
I
V = 5 V
50
40
30
20
I
V = 4.2 V
I
V = 5 V
I
30
20
T
= 25°C
A
V
= 1.8 V
O
10
0
10
0
PWM/PFM Mode
0.01
0.1
1
10
100 1 k
10 k
0.01
0.1
I
1
10
100
1 k
10 k
I
- Output Current - mA
- Output Current - mA
O
O
Figure 5.
Figure 6.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
DCDC2: OUTPUT VOLTAGE
vs
DCDC3: OUTPUT VOLTAGE
vs
OUTPUT CURRENT at 85°C
OUTPUT CURRENT at 85°C
T
= 85°C
T
= 85°C
A
A
3.354
3.334
3.314
3.294
3.274
3.354
3.334
3.314
3.294
3.274
DEFDCDC3 = VINDCDC3
DEFDCDC2 = VINDCDC2
V = 3.8 V
I
V = 4 V
I
V = 3.5 V
I
V = 3.9 V
V = 3.7 V
I
I
V = 3.8 V
I
V = 3.6 V
I
V = 3.7 V
I
V = 3.6 V
I
V = 3.5 V
I
3.254
3.234
3.254
3.234
1
10
1
0.1
10
0.1
I
- Output Current - A
I
- Output Current - A
O
O
Figure 7.
VDCDC1 LINE TRANSIENT RESPONSE
Figure 8.
VDCDC2 LINE TRANSIENT RESPONSE
VINDCDC2
C1 High
4.01 V
VINDCDC1
C1 High
4.71 V
C1 Low
3.02 V
C1 Low
3.68 V
C2 Pk-Pk
48.9 mV
C2 Pk-Pk
28.5 mV
VDCDC2
VDCDC1
C2 Mean
1.81053 V
C2 Mean
1.18925 V
I
= 100 mA
O
I
= 100 mA
O
VINDCDC2 = 3 V - 4 V
DEFDCDC2 = GND
PWW Mode
VINDCDC1 = 3.7 V - 4.7 V
DEFDCDC1 = VINDCDC1
PWW Mode
Figure 9.
Figure 10.
16
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
VDCDC3 LINE TRANSIENT RESPONSE
VDCDC1 LOAD TRANSIENT RESPONSE
VINDCDC3
C1 High
4.20 V
C1 Low
3.59 V
C2 Pk-Pk
60.4 mV
VDCDC3
C2 Mean
3.28264 V
I
= 100 mA
O
VINDCDC3 = 3.6 V - 4.2 V
DEFDCDC3 = VINDCDC3
PWW Mode
Figure 11.
VDCDC2 LOAD TRANSIENT RESPONSE
Figure 12.
VDCDC3 LOAD TRANSIENT RESPONSE
VDCDC3 = 3.3 V @ 50 mV/Div
(AC Coupled)
ILOAD @ 500 mA/Div
800 mA
100 mA
VIN = 3.8 V
TIMESCALE = 50 ms/Div
Figure 13.
Figure 14.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
VDCDC2 OUTPUT VOLTAGE RIPPLE
VDCDC2 OUTPUT VOLTAGE RIPPLE
Figure 15.
Figure 16.
STARTUP VDCDC1, VDCDC2, AND VDCDC3
VDCDC2 OUTPUT VOLTAGE RIPPLE
mV
Figure 17.
Figure 18.
18
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
STARTUP LDO1 AND LDO2
LDO1 LINE TRANSIENT RESPONSE
I
= 25 mA
= 1.1 V
O
ENABLE
Ch1 = V
Ch2 = V
I
V
T
C1 High
3.83 V
O
O
= 25oC
A
C1 Low
3.29 V
LDO1
C2 PK-PK
6.2 mV
C2 Mean
1.09702 V
LDO2
Figure 19.
LDO2 LINE TRANSIENT RESPONSE
Figure 20.
VRTC LINE TRANSIENT RESPONSE
I
= 10 mA
= 3 V
O
I
= 25 mA
= 3.3 V
Ch1 = V
O
I
Ch1 = V
I
V
T
C1 High
3.82 V
O
V
T
C1 High
4.51 V
Ch2 = V
O
O
= 25oC
Ch2 = V
O
= 25oC
A
A
C1 Low
3.28 V
C1 Low
3.99 V
C2 PK-PK
22.8 mV
C2 PK-PK
6.1 mV
C2 Mean
2.98454 V
C2 Mean
3.29828 V
Figure 21.
Figure 22.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
LDO1 LOAD TRANSIENT RESPONSE
LDO2 LOAD TRANSIENT RESPONSE
C4 High
47.8 mA
C4 High
48.9 mA
C4 Low
-2.9 mA
C4 Low
2.1 mA
C2 PK-PK
40.4 mV
C2 PK-PK
42.5 mV
C2 Mean
3.29821 V
C2 Mean
1.09664 V
V = 4 V
I
V = 3.3 V
I
V
T
= 3.3 V
= 25oC
Ch2 = V
Ch4 = I
V
T
= 1.1 V
= 25oC
O
O
O
Ch2 = V
Ch4 = I
O
A
O
A
O
Figure 23.
Figure 24.
VRTC LOAD TRANSIENT RESPONSE
C4 High
21.4 mA
C4 Low
-1.4 mA
C2 PK-PK
76 mV
C2 Mean
2.9762 V
V = 3.8 V
I
Ch2 = V
V
T
= 3 V
= 25oC
O
O
Ch4 = I
O
A
Figure 25.
20
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
DETAILED DESCRIPTION
VRTC OUTPUT AND OPERATION WITH OR WITHOUT BACKUP BATTERY
The VRTC pin is an always-on output, intended to supply up to 30 mA to a permanently required rail (i.e. for a
Real Time Clock). The TPS65023, TPS65023B asserts the RESPWRON signal if VRTC drops below 2.4 V.
VRTC is selected from a priority scheme based on the VSYSIN and VBACKUP inputs.
When the voltage at the VSYSIN pin exceeds 2.65 V, VRTC connects to the VSYSIN input via a PMOS switch
and all other paths to VRTC are disabled. The PMOS switch drops a maximum of 375 mV at 30 mA, which
should be considered when using VRTC. VSYSIN can be connected to any voltage source with the appropriate
input voltage, including VCC or, if set to 3.3 V output, DCDC2 or DCDC3. When VSYSIN falls below 2.65 V or
shorts to ground, the PMOS switch connecting VRTC and VSYSIN opens and VRTC then connects to either
VBACKUP or the output of a dedicated 3V/30mA LDO. Texas Instruments recommends connecting VSYSIN to
VCC or ground - VCC if a non-replaceable primary cell is connected to VBACKUP and ground if the VRTC
output will float.
If the PMOS switch between VSYSIN and VRTC is open and VBACKUP exceeds 2.65 V, VRTC connects to
VBACKUP via a PMOS switch. The PMOS switch drops a maximum of 375 mV at 30 mA, which should be
considered if using VRTC. A typical application may connect VBACKUP to a primary Li button cell, but any
battery that provides a voltage between 2.65 V and 6 V (i.e. a single Li-Ion cell or a single boosted NiMH battery)
is acceptable, to supply the VRTC output. In systems with no backup battery, the VBACKUP pin should be
connected to GND.
If the switches between VRTC and VSYSIN or VBACKUP are open, the dedicated 3-V/30-mA LDO, driven from
VCC, connects to VRTC. This LDO is disabled if the voltage at the VSYSIN input exceeds 2.65 V.
Inside TPS65023, TPS65023B there is a switch (Vmax switch) which selects the higher voltage between VCC
and VBACKUP. This is used as the supply voltage for some basic functions. The functions powered from the
output of the Vmax switch are:
•
•
•
•
•
•
•
•
•
INT output
RESPWRON output
HOT_RESET input
LOW_BATT output
PWRFAIL output
Enable pins for dc-dc converters, LDO1 and LDO2
Undervoltage lockout comparator (UVLO)
Reference system with low frequency timing oscillators
LOW_BATT and PWRFAIL comparators
The main 2.25-MHz oscillator, and the I2C™ interface are only powered from VCC
.
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
Submit Documentation Feedback
21
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
V
VSYSIN
CC
VBACKUP
V
V
ref
ref
V_VSYSIN
V_VBACKUP
V_VSYSIN
EN
VRTC
LDO
V_VBACKUP
priority
#1
priority
#2
priority
#3
VRTC
RESPWRON
V
ref
A. V_VSYSIN, V_VBACKUP thresholds: falling = 2.55 V, rising = 2.65 V ±3%
B. RESPWRON thresholds: falling = 2.4 V, rising = 2.52 V ±3%
Figure 26.
STEP-DOWN CONVERTERS, VDCDC1, VDCDC2, and VDCDC3
The TPS65023, TPS65023B incorporates three synchronous step-down converters operating typically at 2.25
MHz fixed frequency pulse width modulation (PWM) at moderate to heavy load currents. At light load currents,
the converters automatically enter the power save mode (PSM), and operate with pulse frequency modulation
(PFM). The VDCDC1 converter is capable of delivering 1.5 A output current, the VDCDC2 converter is capable
of delivering 1.2 A and the VDCDC3 converter is capable of delivering up to 1 A.
The converter output voltages can be programmed via the DEFDCDC1, DEFDCDC2 and DEFDCDC3 pins. The
pins can either be connected to GND, VCC, or to a resistor divider between the output voltage and GND. The
VDCDC1 converter defaults to 1.2 V or 1.6 V depending on the DEFDCDC1 configuration pin. If DEFDCDC1 is
tied to ground, the default is 1.2 V. If it is tied to VCC, the default is 1.6 V. When the DEFDCDC1 pin is
connected to a resistor divider, the output voltage can be set in the range of 0.6 V to VINDCDC1 V. See the
application information section for more details. The core voltage can be reprogrammed via the serial interface in
the range of 0.8 V to 1.6 V with a programmable slew rate. The converter is forced into PWM operation whilst
any programmed voltage change is underway, whether the voltage is being increased or decreased. The
DEFCORE and DEFSLEW registers are used to program the output voltage and slew rate during voltage
transitions.
The VDCDC2 converter defaults to 1.8 V or 3.3 V depending on the DEFDCDC2 configuration pin. If DEFDCDC2
is tied to ground, the default is 1.8 V. If it is tied to VCC, the default is 3.3 V. When the DEFDCDC2 pin is
connected to a resistor divider, the output voltage can be set in the range of 0.6 V to VINDCDC2 V.
The VDCDC3 converter defaults to 1.8 V or 3.3 V depending on the DEFDCDC3 configuration pin. If DEFDCDC3
is tied to ground the default is 1.8 V. If it is tied to VCC, the default is 3.3 V. When the DEFDCDC3 pin is
connected to a resistor divider, the output voltage can be set in the range of 0.6 V to VINDCDC3 V.
The step-down converter outputs (when enabled) are monitored by power good (PG) comparators, the outputs of
which are available via the serial interface. The outputs of the dc-dc converters can be optionally discharged via
on-chip 300-Ω resistors when the dc-dc converters are disabled.
22
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
During PWM operation, the converters use a unique fast response voltage mode controller scheme with input
voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal, the P-channel MOSFET switch is
turned on. The inductor current ramps up until the comparator trips and the control logic turns off the switch. The
current limit comparator also turns off the switch if the current limit of the P-channel switch is exceeded. After the
adaptive dead time used to prevent shoot through current, the N-channel MOSFET rectifier is turned on, and the
inductor current ramps down. The next cycle is initiated by the clock signal, again turning off the N-channel
rectifier and turning on the P-channel switch.
The three dc-dc converters operate synchronized to each other with the VDCDC1 converter as the master. A
180° phase shift between the VDCDC1 switch turn on and the VDCDC2 and a further 90° shift to the VDCDC3
switch turn on decreases the input RMS current and smaller input capacitors can be used. This is optimized for a
typical application where the VDCDC1 converter regulates a Li-Ion battery voltage of 3.7 V to 1.2 V, the
VDCDC2 converter from 3.7 V to 1.8 V, and the VDCDC3 converter from 3.7 V to 3.3 V. The phase of the three
converters can be changed using the CON_CTRL register.
POWER SAVE MODE OPERATION
As the load current decreases, the converters enter the power save mode operation. During PSM, the converters
operate in a burst mode (PFM mode) with a frequency between 750 kHz and 2.25 MHz, nominal for one burst
cycle. However, the frequency between different burst cycles depends on the actual load current and is typically
far less than the switching frequency with a minimum quiescent current to maintain high efficiency.
In order to optimize the converter efficiency at light load, the average current is monitored and if in PWM mode
the inductor current remains below a certain threshold, then PSM is entered. The typical threshold to enter PSM
is calculated as follows:
VINDCDC1
I
=
PFMDCDC1 enter
24 W
VINDCDC2
I
I
=
=
PFMDCDC2 enter
26 W
VINDCDC3
PFMDCDC3 enter
39 W
(1)
During the PSM the output voltage is monitored with a comparator, and by maximum skip burst width. As the
output voltage falls below the threshold, set to the nominal VO, the P-channel switch turns on and the converter
effectively delivers a constant current defined as follows.
VINDCDC1
I
=
PFMDCDC1 leave
18 W
VINDCDC2
I
I
=
PFMDCDC2 leave
20 W
VINDCDC3
=
PFMDCDC3 leave
29 W
(2)
If the load is below the delivered current then the output voltage rises until the same threshold is crossed in the
other direction. All switching activity ceases, reducing the quiescent current to a minimum until the output voltage
has again dropped below the threshold. The power save mode is exited, and the converter returns to PWM mode
if either of the following conditions are met:
1. the output voltage drops 2% below the nominal VO due to increasing load current
2. the PFM burst time exceeds 16 × 1/fs (7.11 μs typical).
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
These control methods reduce the quiescent current to typically 14 μA per converter, and the switching activity to
a minimum, thus achieving the highest converter efficiency. Setting the comparator thresholds at the nominal
output voltage at light load current results in a low output voltage ripple. The ripple depends on the comparator
delay and the size of the output capacitor. Increasing capacitor values makes the output ripple tend to zero. The
PSM is disabled through the I2C interface to force the individual converters to stay in fixed frequency PWM
mode.
LOW RIPPLE MODE
Setting Bit 3 in register CON-CTRL to 1 enables the low ripple mode for all of the dc-dc converters if operated in
PFM mode. For an output current less than approximately 10 mA, the output voltage ripple in PFM mode is
reduced, depending on the actual load current. The lower the actual output current on the converter, the lower
the output ripple voltage. For an output current above 10 mA, there is only minor difference in output voltage
ripple between PFM mode and low ripple PFM mode. As this feature also increases switching frequency, it is
used to keep the switching frequency above the audible range in PFM mode down to a low output current.
SOFT START
Each of the three converters has an internal soft start circuit that limits the inrush current during start-up. The soft
start is realized by using a low current to initially charge the internal compensation capacitor. The soft start time
is typically 750 μs if the output voltage ramps from 5% to 95% of the final target value. If the output is already
precharged to some voltage when the converter is enabled, then this time is reduced proportionally. There is a
short delay of typically 170 μs between the converter being enabled and switching activity actually starting. This
allows the converter to bias itself properly, to recognize if the output is precharged, and if so to prevent
discharging of the output while the internal soft start ramp catches up with the output voltage.
100% DUTY CYCLE LOW DROPOUT OPERATION
The TPS65023, TPS65023B converters offer a low input to output voltage difference while still maintaining
operation with the use of the 100% duty cycle mode. In this mode the P-channel switch is constantly turned on.
This is particularly useful in battery-powered applications to achieve longest operation time by taking full
advantage of the whole battery voltage range. The minimum input voltage required to maintain dc regulation
depends on the load current and output voltage. It is calculated as:
ǒr
max ) R Ǔ
Vin
+ Vout
) Iout
max
min
min
DS(on)
L
(3)
with:
Ioutmax = maximum load current (Note: ripple current in the inductor is zero under these conditions)
rDS(on)max = maximum P-channel switch rDS(on)
RL = DC resistance of the inductor
Voutmin = nominal output voltage minus 2% tolerance limit
ACTIVE DISCHARGE WHEN DISABLED
When the VDCDC1, VDCDC2, and VDCDC3 converters are disabled, due to an UVLO, DCDC_EN or
OVERTEMP condition, it is possible to actively pull down the outputs. This feature is disabled per default and is
individually enabled via the CON_CTRL2 register in the serial interface. When this feature is enabled, the
VDCDC1, VDCDC2, and VDCDC3 outputs are discharged by a 300 Ω (typical) load which is active as long as
the converters are disabled.
POWER GOOD MONITORING
All three step-down converters and both the LDO1 and LDO2 linear regulators have power good comparators.
Each comparator indicates when the relevant output voltage has dropped 10% below its target value with 5%
hysteresis. The outputs of these comparators are available in the PGOODZ register via the serial interface. An
interrupt is generated when any voltage rail drops below the 10% threshold. The comparators are disabled when
the converters are disabled and the relevant PGOODZ register bits indicate that power is good.
24
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
LOW DROPOUT VOLTAGE REGULATORS
The low dropout voltage regulators are designed to operate well with low value ceramic input and output
capacitors. They operate with input voltages down to 1.5 V. The LDOs offer a maximum dropout voltage of
300 mV at rated output current. Each LDO supports a current limit feature. Both LDOs are enabled by the
LDO_EN pin, both LDOs can be disabled or programmed via the serial interface using the REG_CTRL and
LDO_CTRL registers. The LDOs also have reverse conduction prevention. This allows the possibility to connect
external regulators in parallel in systems with a backup battery. The TPS65023, TPS65023B step-down and LDO
voltage regulators automatically power down when the VCC voltage drops below the UVLO threshold or when the
junction temperature rises above 160°C.
POWER GOOD MONITORING
Both the LDO1 and LDO2 linear regulators have power good comparators. Each comparator indicates when the
relevant output voltage has dropped 10% below its target value, with 5% hysteresis. The outputs of these
comparators are available in the PGOODZ register via the serial interface. An interrupt is generated when any
voltage rail drops below the 10% threshold. The comparators are disabled when the LDOs are disabled and the
relevant PGOODZ register bits indicate that power is good.
UNDERVOLTAGE LOCKOUT
The undervoltage lockout circuit for the five regulators on the TPS65023, TPS65023B prevents the device from
malfunctioning at low-input voltages and from excessive discharge of the battery. It disables the converters and
LDOs. The UVLO circuit monitors the VCC pin, the threshold is set internally to 2.35 V with 5% (120 mV)
hysteresis. Note that when any of the dc-dc converters are running, there is an input current at the VCC pin,
which is up to 3 mA when all three converters are running in PWM mode. This current needs to be taken into
consideration if an external RC filter is used at the VCC pin to remove switching noise from the TPS65023,
TPS65023B internal analog circuitry supply.
POWER-UP SEQUENCING
The TPS65023, TPS65023B power-up sequencing is designed to be entirely flexible and customer driven. This is
achieved by providing separate enable pins for each switch-mode converter, and a common enable signal for the
LDOs. The relevant control pins are described in Table 2.
Table 2. Control Pins and Status Outputs for DC-DC Converters
PIN NAME
I/O
FUNCTION
Defines the default voltage of the VDCDC3 switching converter. DEFDCDC3 = 0 defaults VDCDC3 to 1.8 V,
DEFDCDC3 = VCC defaults VDCDC3 to 3.3 V.
DEFDCDC3
I
Defines the default voltage of the VDCDC2 switching converter. DEFDCDC2 = 0 defaults VDCDC2 to 1.8 V,
DEFDCDC2 = VCC defaults VDCDC2 to 3.3 V.
DEFDCDC2
DEFDCDC1
I
I
Defines the default voltage of the VDCDC1 switching converter. DEFDCDC1 = 0 defaults VDCDC1 to 1.2 V,
DEFDCDC1 = VCC defaults VDCDC1 to 1.6 V.
DCDC3_EN
DCDC2_EN
DCDC1_EN
I
I
I
Set DCDC3_EN = 0 to disable and DCDC3_EN = 1 to enable the VDCDC3 converter
Set DCDC2_EN = 0 to disable and DCDC2_EN = 1 to enable the VDCDC2 converter
Set DCDC1_EN = 0 to disable and DCDC1_EN = 1 to enable the VDCDC1 converter
The HOT_RESET pin generates a reset (RESPWRON) for the processor.HOT_RESET does not alter any
TPS65023, TPS65023B settings except the output voltage of VDCDC1. Activating HOT_RESET sets the voltage
of VDCDC1 to its default value defined with the DEFDCDC1 pin. HOT_RESET is internally de-bounced by the
TPS65023, TPS65023B.
HOT_RESET
I
RESPWRON is held low when power is initially applied to the TPS65023, TPS65023B. The VRTC voltage is
monitored: RESWPRON is low when VRTC < 2.4 V and remains low for a time defined by the external capacitor
at the TRESPWRON pin. RESPWRON can also be forced low by activation of the HOT_RESET pin.
RESPWRON
O
I
TRESPWRON
Connect a capacitor here to define the RESET time at the RESPWRON pin (1 nF typically gives 100 ms).
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
SYSTEM RESET + CONTROL SIGNALS
The RESPWRON signal can be used as a global reset for the application. It is an open drain output. The
RESPWRON signal is generated according to the power good comparator of VRTC, and remains low for tnrespwron
seconds after VRTC has risen above 2.52 V (falling threshold is 2.4 V, 5% hysteresis). tnrespwron is set by an
external capacitor at the TRESPWRON pin. 1 nF gives typically 100 ms. RESPWRON is also triggered by the
HOT_RESET input. This input is internally debounced, with a filter time of typically 30 ms.
The PWRFAIL and LOW_BAT signals are generated by two voltage detectors using the PWRFAIL_SNS and
LOWBAT_SNS input signals. Each input signal is compared to a 1 V threshold (falling edge) with 5% (50 mV)
hysteresis.
The DCDC1 converter is reset to its default output voltage defined by the DEFDCDC1 input, when HOT_RESET
is asserted. Other I2C registers are not affected. Generally, the DCDC1 converter is set to its default voltage with
one of these conditions: HOT_RESET active, VRTC lower than its threshold voltage, undervoltage lockout
(UVLO) condition, or RESPWRON active.
DEFLDO1 and DEFLDO2
These two pins are used to set the default output voltage of the two 200 mA LDOs. The digital value applied to
the pins is latched during power up and determines the initial output voltage according to Table 3. The voltage of
both LDOs can be changed during operation with the I2C interface as described in the interface description.
Table 3.
DEFLDO2
DEFLDO1
VLDO1
1.3 V
2.8 V
1.3 V
1.8 V
VLDO2
3.3 V
3.3 V
1.8 V
3.3 V
0
0
1
1
0
1
0
1
Interrupt Management and the INT Pin
The INT pin combines the outputs of the PGOOD comparators from each dc-dc converter and the LDOs. The
INT pin is used as a POWER_OK pin to indicate when all enabled supplies are in regulation. The INT pin
remains active (low state) during power up as long as all enabled power rails are below their regulation limit.
Once the last enabled power rail is within regulation, the INT pin transitions to a high state.
During operation, if one of the enabled supplies goes out of regulation, INT transitions to a low state, and the
corresponding bit in the PGOODZ register goes high. If the supply goes back to its regulation limits, INT
transitions back to a high state.
While INT is in an active low state, reading the PGOODZ register via the I2C bus forces INT into a high-Z state.
Since this pin requires an external pull-up resistor, the INT pin transitions to a logic high state even though the
supply in question is still out of regulation. The corresponding bit in the PGOODZ register still indicates that the
power rail is out of regulation.
Interrupts can be masked using the MASK register; default operation is not to mask any DCDC or LDO interrupts
since this provides the POWER_OK function. If none of the DCDC converters or LDos are enabled, /INT defaults
to a low state independently of the settings of the MASK register.
26
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
TIMING DIAGRAMS
Figure 27. HOT_RESET Timing
2.35V
1.9V
1.2V
2.47V
1.9V
V
CC
0.8V
UVLO*
VRTC
2.52V
2.4V
3.0V
RESPWRON
DCDCx_EN
tNRESPWRON
Ramp within
800 μs
V
DCDCx
O
slope depending
on load
LDO_EN
V
LDOx
O
VSYSIN=VBACKUP=GND;
VINLDO=V
CC
*... internal signal
Figure 28. Power-Up and Power-Down Timing
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
Figure 29. DVS Timing
SERIAL INTERFACE
The serial interface is compatible with the standard and fast mode I2C specifications, allowing transfers at up to
400 kHz. The interface adds flexibility to the power supply solution, enabling most functions to be programmed to
new values depending on the instantaneous application requirements and charger status to be monitored.
Register contents remain intact as long as VCC remains above 2 V. The TPS65023, TPS65023B has a 7-bit
address: 1001000, other addresses are available upon contact with the factory. Attempting to read data from the
register addresses not listed in this section results in FFh being read out.
28
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
For normal data transfer, DATA is allowed to change only when CLK is low. Changes when CLK is high are
reserved for indicating the start and stop conditions. During data transfer, the data line must remain stable
whenever the clock line is high. There is one clock pulse per bit of data. Each data transfer is initiated with a start
condition and terminated with a stop condition. When addressed, the TPS65023, TPS65023B device generates
an acknowledge bit after the reception of each byte. The master device (microprocessor) must generate an extra
clock pulse that is associated with the acknowledge bit. The TPS65023, TPS65023B device must pull down the
DATA line during the acknowledge clock pulse so that the DATA line is a stable low during the high period of the
acknowledge clock pulse. The DATA line is a stable low during the high period of the acknowledge–related clock
pulse. Setup and hold times must be taken into account. During read operations, a master must signal the end of
data to the slave by not generating an acknowledge bit on the last byte that was clocked out of the slave. In this
case, the slave TPS65023, TPS65023B device must leave the data line high to enable the master to generate
the stop condition
DATA
CLK
Data Line
Stable;
Data Valid
Change
of Data
Allowed
Figure 30. Bit Transfer on the Serial Interface
CE
DATA
CLK
S
P
START Condition
STOP Condition
Figure 31. START and STOP Conditions
SCLK
SDAT
A6
A5
A4
A0
ACK
0
R7
R6
R5
R0 ACK
0
D7
D6
D5
D0 ACK
R/W
0
0
Register Address
Stop
Start
Slave Address
Data
Note: SLAVE = TPS65023
Figure 32. Serial i/f WRITE to TPS65023, TPS65023B Device
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
SCLK
SDAT
A6
A0
R/W ACK
R7
R0 ACK
0
A6
A0
R/W ACK
D7
D0 ACK
0
0
1
0
Slave
Drives
the Data
Stop
Register
Address
Master
Drives
ACK and Stop
Start
Slave Address
Slave Address
Repeated
Start
Note: SLAVE = TPS65023
Figure 33. Serial i/f READ from TPS65023, TPS65023B: Protocol A
SCLK
SDA
A6
A0
R/W ACK
R7
R0 ACK
A6
A0
R/W ACK D7
D0
ACK
0
0
0
1
0
Stop Start
Stop
Slave
Drives
the Data
Register
Address
Master
Drives
ACK and Stop
Start
Slave Address
Slave Address
Note: SLAVE = TPS65023
Figure 34. Serial i/f READ from TPS65023, TPS65023B: Protocol B
DATA
t
(BUF)
t
h(STA)
t
(LOW)
t
t
f
r
CLK
t
t
t
(HIGH)
su(STA)
t
su(STO)
h(STA)
t
t
su(DATA)
h(DATA)
STO
STA
STA
STO
Figure 35. Serial i/f Timing Diagram
30
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
Table 4. I2C Timing
I2C timing for TPS65023
Clock frequency
MIN MAX UNIT
fMAX
400
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
twH(HIGH)
twL(LOW)
tR
Clock high time
600
Clock low time
1300
DATA and CLK rise time
DATA and CLK fall time
300
300
tF
th(STA)
tsu(DATA)
th(DATA)
tsu(DATA)
tsu(STO)
t(BUF)
Hold time (repeated) START condition (after this period the first clock pulse is generated)
600
600
Setup time for repeated START condition
Data input hold time
300
Data input setup time
300
STOP condition setup time
Bus free time
600
1300
I2C timing for TPS65023B
MIN MAX UNIT
Operating conditions:
VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 2.5V to 5.5V,
VBACKUP = 3.0V,
TA = -40 °C to +85 °C
fMAX
Clock frequency
400
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
twH(HIGH)
twL(LOW)
tR
Clock high time
600
Clock low time
1300
DATA and CLK rise time
300
300
tF
DATA and CLK fall time
th(STA)
tsu(DATA)
th(DATA)
tsu(DATA)
tsu(STO)
t(BUF)
Hold time (repeated) START condition (after this period the first clock pulse is generated)
600
600
Setup time for repeated START condition
Data input hold time
100
Data input setup time
100
STOP condition setup time
Bus free time
600
1300
VERSION. Register Address: 00h (read only)
VERSION
B7
B6
B5
B4
B3
B2
B1
B0
Bit name and
function
0
0
1
0
0
0
1
1
Read/Write
R
R
R
R
R
R
R
R
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
PGOODZ. Register Address: 01h (read only)
PGOODZ
B7
B6
B5
B4
B3
B2
B1
B0
Bit name and
function
LOWBATTZ
PGOODZ
VDCDC1
PGOODZ
VDCDC2
PGOODZ
VDCDC3
PGOODZ
LDO2
PGOODZ
LDO1
PWRFAILZ
LOWBATT
LOWBATTZ
R
PGOODZ
VDCDC1
PGOODZ
VDCDC2
PGOODZ
VDCDC3
PGOODZ
LDO2
PGOODZ
LDO1
Set by signal
PWRFAIL
Default value
loaded by:
PGOOD
VDCDC1
PGOOD
VDCDC2
PGOOD
VDCDC3
PGOOD
LDO2
PGOOD
LDO1
PWRFAILZ
R
Read/Write
R
R
R
R
R
R
Bit 7 PWRFAILZ:
0 = indicates that the PWRFAIL_SNS input voltage is above the 1-V threshold.
1 = indicates that the PWRFAIL_SNS input voltage is below the 1-V threshold.
Bit 6 LOWBATTZ:
0 = indicates that the LOWBATT_SNS input voltage is above the 1-V threshold.
1 = indicates that the LOWBATT_SNS input voltage is below the 1-V threshold.
Bit 5 PGOODZ VDCDC1:
0 = indicates that the VDCDC1 converter output voltage is within its nominal range. This bit is zero if
the VDCDC1 converter is disabled.
1 = indicates that the VDCDC1 converter output voltage is below its target regulation voltage
Bit 4 PGOODZ VDCDC2:
0 = indicates that the VDCDC2 converter output voltage is within its nominal range. This bit is zero if
the VDCDC2 converter is disabled.
1 = indicates that the VDCDC2 converter output voltage is below its target regulation voltage
Bit 3 PGOODZ VDCDC3: .
0 = indicates that the VDCDC3 converter output voltage is within its nominal range. This bit is zero if
the VDCDC3 converter is disabled and during a DVM controlled output voltage transition
1 = indicates that the VDCDC3 converter output voltage is below its target regulation voltage
Bit 2 PGOODZ LDO2:
0 = indicates that the LDO2 output voltage is within its nominal range. This bit is zero if LDO2 is
disabled.
1 = indicates that LDO2 output voltage is below its target regulation voltage
Bit 1 PGOODZ LDO1
0 = indicates that the LDO1 output voltage is within its nominal range. This bit is zero if LDO1 is
disabled.
1 = indicates that the LDO1 output voltage is below its target regulation voltage
32
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
MASK. Register Address: 02h (read/write)
Default Value: C0h
MASK
B7
B6
B5
B4
B3
B2
B1
B0
Bit name and
function
MASK
PWRFAILZ
MASK
LOWBATTZ
MASK
VDCDC1
MASK
VDCDC2
MASK
VDCDC3
MASK
LDO2
MASK
LDO1
Default
1
1
0
0
0
0
0
0
Default value
loaded by:
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
Read/Write
The MASK register can be used to mask particular fault conditions from appearing at the INT pin. MASK<n> = 1
masks PGOODZ<n>.
REG_CTRL. Register Address: 03h (read/write)
Default Value: FFh
The REG_CTRL register is used to disable or enable the power supplies via the serial interface. The contents of
the register are logically AND’ed with the enable pins to determine the state of the supplies. A UVLO condition
resets the REG_CTRL to 0xFF, so the state of the supplies defaults to the state of the enable pin. The
REG_CTRL bits are automatically reset to default when the corresponding enable pin is low.
REG_CTRL
B7
B6
B5
B4
B3
B2
B1
B0
Bit name and
function
VDCDC1
ENABLE
VDCDC2
ENABLE
VDCDC3
ENABLE
LDO2
ENABLE
LDO1
ENABLE
Default
1
1
1
1
1
1
1
1
Set by signal
DCDC1_ENZ DCDC2_ENZ DCDC3_ENZ
LDO_ENZ
LDO_ENZ
Default value
loaded by:
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
Read/Write
Bit 5 VDCDC1 ENABLE
DCDC1 Enable. This bit is logically AND’ed with the state of the DCDC1_EN pin to turn on the DCDC1
converter. Reset to 1 by a UVLO condition, the bit can be written to 0 or 1 via the serial interface. The
bit is reset to 1 when the pin DCDC1_EN is pulled to GND, allowing DCDC1 to turn on when
DCDC1_EN returns high.
Bit 4 VDCDC2 ENABLE
DCDC2 Enable. This bit is logically AND’ed with the state of the DCDC2_EN pin to turn on the DCDC2
converter. Reset to 1 by a UVLO condition, the bit can be written to 0 or 1 via the serial interface. The
bit is reset to 1 when the pin DCDC2_EN is pulled to GND, allowing DCDC2 to turn on when
DCDC2_EN returns high.
Bit 3 VDCDC3 ENABLE
DCDC3 Enable. This bit is logically AND’ed with the state of the DCDC3_EN pin to turn on the DCDC3
converter. Reset to 1 by a UVLO condition, the bit can be written to 0 or 1 via the serial interface. The
bit is reset to 1 when the pin DCDC3_EN is pulled to GND, allowing DCDC3 to turn on when
DCDC3_EN returns high.
Bit 2 LDO2 ENABLE
LDO2 Enable. This bit is logically AND’ed with the state of the LDO2_EN pin to turn on LDO2. Reset to
1 by a UVLO condition, the bit can be written to 0 or 1 via the serial interface. The bit is reset to 1 when
the pin LDO_EN is pulled to GND, allowing LDO2 to turn on when LDO_EN returns high.
Bit 1 LDO1 ENABLE
LDO1 Enable. This bit is logically AND’ed with the state of the LDO1_EN pin to turn on LDO1. Reset to
1 by a UVLO condition, the bit can be written to 0 or 1 via the serial interface. The bit is reset to 1 when
the pin LDO_EN is pulled to GND, allowing LDO1 to turn on when LDO_EN returns high.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
CON_CTRL. Register Address: 04h (read/write)
Default Value: B1h
CON_CTRL
B7
B6
B5
B4
B3
B2
B1
B0
Bit name and
function
DCDC2
PHASE1
DCDC2
PHASE0
DCDC3
PHASE1
DCDC3
PHASE0
LOW
RIPPLE
FPWM
DCDC2
FPWM
DCDC1
FPWM
DCDC3
Default
1
0
1
1
0
0
0
0
Default value
loaded by:
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
Read/Write
The CON_CTRL register is used to force any or all of the converters into forced PWM operation, when low
output voltage ripple is vital. It is also used to control the phase shift between the three converters in order to
minimize the input rms current, hence reduce the required input blocking capacitance. The DCDC1 converter is
taken as the reference and consequently has a fixed zero phase shift.
DCDC2 CONVERTER
DELAYED BY
DCDC3 CONVERTER
DELAYED BY
CON_CTRL<7:6>
CON_CTRL<5:4>
00
01
10
11
zero
00
01
10
11
zero
1/4 cycle
1/2 cycle
3/4 cycle
1/4 cycle
1/2 cycle
3/4 cycle
Bit 3 LOW RIPPLE:
0 =
1 =
PFM mode operation optimized for high efficiency for all converters
PFM mode operation optimized for low output voltage ripple for all converters
Bit 2 FPWM DCDC2:
0 =
1 =
DCDC2 converter operates in PWM / PFM mode
DCDC2 converter is forced into fixed frequency PWM mode
Bit 1 FPWM DCDC1:
0 =
1 =
DCDC1 converter operates in PWM / PFM mode
DCDC1 converter is forced into fixed frequency PWM mode
Bit 0 FPWM DCDC3:
0 =
1 =
DCDC3 converter operates in PWM / PFM mode
DCDC3 converter is forced into fixed frequency PWM mode
34
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
CON_CTRL2. Register Address: 05h (read/write)
Default Value: 40h
CON_CTRL2
B7
GO
0
B6
B5
B4
B3
B2
B1
B0
Bit name and
function
Core adj
allowed
DCDC2
discharge
DCDC1
discharge
DCDC3
discharge
Default
1
0
0
0
0
0
0
Default value
loaded by:
UVLO +
DONE
RESET(1)
UVLO
R/W
UVLO
R/W
UVLO
R/W
Read/Write
R/W
R/W
The CON_CTRL2 register can be used to take control the inductive converters.
RESET(1): CON_CTRL2[6] is reset to its default value by one of these events:
undervoltage lockout (UVLO)
HOT_RESET pulled low
RESPWRON active
VRTC below threshold
•
•
•
•
Bit 7
GO:
0 = no change in the output voltage for the DCDC1 converter
1 = the output voltage of the DCDC1 converter is changed to the value defined in DEFCORE with
the slew rate defined in DEFSLEW. This bit is automatically cleared when the DVM transition is
complete. The transition is considered complete in this case when the desired output voltage
code has been reached, not when the VDCDC1 output voltage is actually in regulation at the
desired voltage.
Bit 6
CORE ADJ Allowed:
0 = the output voltage is set with the I2C register
1 = DEFDCDC1 is either connected to GND or VCC or an external voltage divider. When
connected to GND or VCC, VDCDC1 defaults to 1.2 V or 1.6 V respectively at start-up
Bit 2– 0 0 = the output capacitor of the associated converter is not actively discharged when the converter is
disabled
1 = the output capacitor of the associated converter is actively discharged when the converter is
disabled. This decreases the fall time of the output voltage at light load
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
DEFCORE. Register Address: 06h (read/write
Default Value: 14h/1Eh
DEFCORE
B7
B6
B5
B4
CORE4
1
B3
B2
B1
B0
Bit name and
function
CORE3
CORE2
CORE1
CORE0
Default
0
0
0
DEFDCDC1 DEFDCDC1 DEFDCDC1 DEFDCDC1
Default value
loaded by:
RESET(1)
R/W
RESET(1)
R/W
RESET(1)
R/W
RESET(1)
R/W
RESET(1)
R/W
Read/Write
RESET(1): DEFCORE is reset to its default value by one of these events:
•
•
•
•
undervoltage lockout (UVLO)
HOT_RESET pulled low
RESPWRON active
VRTC below threshold
CORE4 CORE3 CORE2 CORE1 CORE0
VDCDC1
0.8 V
CORE4
CORE3
CORE2
CORE1 CORE0
VDCDC1
1.2 V
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0.825 V
0.85 V
0.875 V
0.9 V
1.225 V
1.25 V
1.275 V
1.3 V
0.925 V
0.95 V
0.975 V
1 V
1.325 V
1.35 V
1.375 V
1.4 V
1.025 V
1.05 V
1.075 V
1.1 V
1.425 V
1.45 V
1.475 V
1.5 V
1.125 V
1.15 V
1.175 V
1.525 V
1.55 V
1.6 V
36
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
DEFSLEW. Register Address: 07h (read/write)
Default Value: 06h
DEFSLEW
B7
B6
B5
B4
B3
B2
SLEW2
1
B1
SLEW1
1
B0
SLEW0
0
Bit name and
function
Default
Default value
loaded by:
UVLO
R/W
UVLO
R/W
UVLO
R/W
Read/Write
SLEW2
SLEW1
SLEW0
VDCDC1 SLEW RATE
0.225 mV/μs
0.45 mV/μs
0.9 mV/μs
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1.8 mV/μs
3.6 mV/μs
7.2 mV/μs
14.4 mV/μs
Immediate
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
37
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
LDO_CTRL. Register Address: 08h (read/write)
Default Value: set with DEFLDO1 and DEFLDO2
LDO_CTRL
B7
B6
LDO2_2
DEFLDOx
UVLO
B5
LDO2_1
DEFLDOx
UVLO
B4
LDO2_0
DEFLDOx
UVLO
B3
B2
LDO1_2
DEFLDOx
UVLO
B1
LDO1_1
DEFLDOx
UVLO
B0
LDO1_0
DEFLDOx
UVLO
Bit name and
function
RSVD
RSVD
Default
Default value
loaded by:
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
The LDO_CTRL registers are used to set the output voltage of LDO1 and LDO2. LDO_CTRL[7] and
LDO_CTRL[3] are reserved and should always be written to 0.
The default voltage is set with DEFLDO1 and DEFLDO2 pins as described in Table 3.
LDO2 OUTPUT
VOLTAGE
LDO1 OUTPUT
VOLTAGE
LDO2_2
LDO2_1
LDO2_0
LDO1_2
LDO1_1
LDO1_0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1.05 V
1.2 V
1.3 V
1.8 V
2.5 V
2.8 V
3.0 V
3.3 V
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1 V
1.1 V
1.3 V
1.8 V
2.2 V
2.6 V
2.8 V
3.15 V
DESIGN PROCEDURE
Inductor Selection for the DC-DC Converters
Each of the converters in the TPS65023, TPS65023B typically use a 2.2 μH output inductor. Larger or smaller
inductor values are used to optimize the performance of the device for specific operation conditions. The
selected inductor has to be rated for its dc resistance and saturation current. The dc resistance of the inductance
influences directly the efficiency of the converter. Therefore, an inductor with lowest dc resistance should be
selected for highest efficiency.
For a fast transient response, a 2.2-μH inductor in combination with a 22-μF output capacitor is recommended.
Equation 5 calculates the maximum inductor current under static load conditions. The saturation current of the
inductor should be rated higher than the maximum inductor current as calculated with Equation 5. This is needed
because during heavy load transient the inductor current rises above the value calculated under Equation 5.
Vout
Vin
1 *
DI + Vout
L
L ƒ
(4)
(5)
DI
L
I
+ I
)
outmax
Lmax
2
with:
f = Switching Frequency (2.25 MHz typical)
L = Inductor Value
ΔIL = Peak-to-Peak inductor ripple current
ILMAX = Maximum Inductor current
The highest inductor current occurs at maximum Vin.
Open core inductors have a soft saturation characteristic, and they can usually handle higher inductor currents
versus a comparable shielded inductor.
38
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
A conservative approach is to select the inductor current rating just for the maximum switch current of the
TPS65023, TPS65023B (2 A for the VDCDC1 and VDCDC2 converters, and 1.5 A for the VDCDC3 converter).
The core material from inductor to inductor differs and has an impact on the efficiency especially at high
switching frequencies.
See Table 5 and the typical applications for possible inductors.
Table 5. Tested Inductors
DEVICE
INDUCTOR
VALUE
TYPE
COMPONENT SUPPLIER
2.2 μH
2.2 μH
2.2uH
LPS4012-222LMB
VLCF4020T-2R2N1R7
LQH32PN2R2NN0
Coilcraft
TDK
All Converters
For DCDC2 or
DCDC3
Murata
For DCDC1
1.5uH
2.2uH
LQH32PN1R5NN0
PST25201B-2R2MS
Murata
Cyntec
All converters
Output Capacitor Selection
The advanced Fast Response voltage mode control scheme of the inductive converters implemented in the
TPS65023, TPS65023B allow the use of small ceramic capacitors with a typical value of 10 μF for each
converter without having large output voltage under and overshoots during heavy load transients. Ceramic
capacitors having low ESR values have the lowest output voltage ripple and are recommended. See Table 6 for
recommended components.
If ceramic output capacitors are used, the capacitor RMS ripple current rating always meets the application
requirements. Just for completeness, the RMS ripple current is calculated as:
V
out
1 -
V
1
in
x
I
= V
x
RMSCout
out
L x ¦
2 x Ö3
(6)
At nominal load current, the inductive converters operate in PWM mode. The overall output voltage ripple is the
sum of the voltage spike caused by the output capacitor ESR plus the voltage ripple caused by charging and
discharging the output capacitor:
V
out
1 -
V
in
1
DV
= V
x
x
+ ESR
out
out
L x ¦
8 x C
x ¦
out
(7)
Where the highest output voltage ripple occurs at the highest input voltage Vin.
At light load currents, the converters operate in PSM and the output voltage ripple is dependent on the output
capacitor value. The output voltage ripple is set by the internal comparator delay and the external capacitor. The
typical output voltage ripple is less than 1% of the nominal output voltage.
Input Capacitor Selection
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes. Each dc-dc converter requires a 10-μF ceramic input capacitor on its input pin VINDCDCx. The
input capacitor is increased without any limit for better input voltage filtering. The VCC pin is separated from the
input for the dc-dc converters. A filter resistor of up to 10R and a 1-μF capacitor is used for decoupling the VCC
pin from switching noise. Note that the filter resistor may affect the UVLO threshold since up to 3 mA can flow via
this resistor into the VCC pin when all converters are running in PWM mode.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
39
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
Table 6. Possible Capacitors
CAPACITOR VALUE
CASE SIZE
1206
COMPONENT SUPPLIER
COMMENTS
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
22 μF
22 μF
22 μF
22μF
TDK C3216X5R0J226M
Taiyo Yuden JMK316BJ226ML
TDK C2012X5R0J226MT
1206
0805
0805
0805
0805
Taiyo Yuden JMK212BJ226MG
Taiyo Yuden JMK212BJ106M
TDK C2012X5R0J106M
10 μF
10 μF
Output Voltage Selection
The DEFDCDC1, DEFDCDC2, and DEFDCDC3 pins are used to set the output voltage for each step-down
converter. See Table 7 for the default voltages if the pins are pulled to GND or to VCC. If a different voltage is
needed, an external resistor divider can be added to the DEFDCDCx pin as shown in Figure 36.
The output voltage of VDCDC1 is set with the I2C interface. If the voltage is changed from the default, using the
DEFCORE register, the output voltage only depends on the register value. Any resistor divider at DEFDCDC1
does not change the voltage set with the register.
Table 7.
PIN
LEVEL
VCC
GND
VCC
GND
VCC
GND
DEFAULT OUTPUT VOLTAGE
1.6 V
1.2 V
3.3 V
1.8 V
3.3 V
1.8 V
DEFDCDC1
DEFDCDC2
DEFDCDC3
Using an external resistor divider at DEFDCDCx:
10 R
V
V
(bat)
CC
1 mF
VDCDC3
V
L3
O
VINDCDC3
DCDC3_EN
L
C
I
C
O
R1
R2
DEFDCDC3
AGND PGND
Figure 36. External Resistor Divider
When a resistor divider is connected to DEFDCDCx, the output voltage can be set from 0.6 V up to the input
voltage V(bat). The total resistance (R1+R2) of the voltage divider should be kept in the 1-MR range in order to
maintain a high efficiency at light load.
V(DEFDCDCx) = 0.6 V
V
OUT
R1 + R2
V
= V
x
- R2
R1 = R2 x
OUT
DEFDCDCx
V
R2
DEFDCDCx
(8)
40
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
VRTC Output
It is required that a 4.7-μF (minimum) capacitor be added to the VRTC pin even if the output is not used.
LDO1 and LDO2
The LDOs in the TPS65023, TPS65023B are general-purpose LDOs which are stable using ceramics capacitors.
The minimum output capacitor required is 2.2 μF. The LDOs output voltage can be changed to different voltages
between 1 V and 3.3 V using the I2C interface. Therefore, they can also be used as general-purpose LDOs in
applications powering processors different from DaVinci. The supply voltage for the LDOs needs to be connected
to the VINLDO pin, giving the flexibility to connect the lowest voltage available in the system and provides the
highest efficiency.
TRESPWRON
This is the input to a capacitor that defines the reset delay time after the voltage at VRTC rises above 2.52 V.
The timing is generated by charging and discharging the capacitor with a current of 2 μA between a threshold of
0.25 V and 1 V for 128 cycles. A 1-nF capacitor gives a delay time of 100 ms.
While there is no real upper and lower limit for the capacitor connected to TRESPWRON, it is recommended to
not leave signal pins open.
(1 V - 0.25 V) x C(reset)
t(reset) = 2 x 128 x
2 mA
(9)
Where:
t(reset) is the reset delay time
C(reset) is the capacitor connected to the TRESPWRON pin
The minimum and maximum values for the timing parameters called ICONST (2uA), TRESPWRON_UPTH (1V)
and TRESPWRON_LOWTH (0.25V) can be found under the electrical characteristics.
VCC-Filter
An RC filter connected at the VCC input is used to keep noise from the internal supply for the bandgap and other
analog circuitry. A typical value of 1 R and 1 μF is used to filter the switching spikes, generated by the dc-dc
converters. A larger resistor than 10 R should not be used because the current into VCC of up to 3 mA causes a
voltage drop at the resistor causing the undervoltage lockout circuitry connected at VCC internally to switch off
too early.
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
41
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
APPLICATION INFORMATION
Layout Considerations
As for all switching power supplies, the layout is an important step in the design. Proper function of the device
demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If
the layout is not carefully done, the regulators may show poor line and/or load regulation, and stability issues as
well as EMI problems. It is critical to provide a low impedance ground path. Therefore, use wide and short traces
for the main current paths. The input capacitors should be placed as close as possible to the IC pins as well as
the inductor and output capacitor.
For TPS65023, TPS65023B, connect the PGND pins of the device to the PowerPAD™ land of the PCB and
connect the analog ground connections (AGND) to the PGND at the PowerPAD™. It is essential to provide a
good thermal and electrical connection of all GND pins using multiple vias to the GND-plane. Keep the common
path to the AGND pins, which returns the small signal components, and the high current of the output capacitors
as short as possible to avoid ground noise. The VDCDCx line should be connected right to the output capacitor
and routed away from noisy components and traces (for example, the L1, L2 and L3 traces).
Input Voltage Connection
The low power section of the control circuit for the step-down converters DCDC1, DCDC2 and DCDC3 is
supplied by the Vcc pin while the circuitry with high power such as the power stage is powered from the
VINDCDC1, VINDCDC2 and VINDCDC3 pins. For proper operation of the step-down converters, VINDCDC1,
VINDCDC2,VNDCDC3 and Vcc need to be tied to the same voltage rail. Step-down converters that are plannned
to be not used, still need to be powered from their input pin on the same rails than the other step-down
converters and Vcc.
LDO1 and LDO2 share a supply voltage pin which can be powered from the Vcc rails or from a voltage lower
than Vcc e.g. the output of one of the step-down converters as long as it is operated within the input voltage
range of the LDOs. If both LDOs are not used, the VINLDO pin can be tied to GND.
Requirements for Supply Voltages below 3.0V
For a supply voltage on pins Vcc, VINDCDC1, VINDCDC2 and VINDCDC3 below 3.0V, it is recommended to
enable the DCDC1, DCDC2 and DCDC3 converters in sequence. If all 3 step-down converters are enabled at
the same time while the supply voltage is close to the internal reset detection threshold, a reset may be
generated during power-up. Therefore it is recommended to enable the dcdc convertes in sequence. This can be
done by driving one or two of the enable pins with a RC delay or by driving the enable pin by the output voltage
of one of the other step-down converters. If a voltage above 3.0V is applied on pin VBACKUP while Vcc and
VINDCDCx is below 3.0V, there is no restriction in the power-up sequencing as VBACKUP will be used to power
the internal circuitry.
Unused Regulators
In case a step-down converter is not used, its input supply voltage pin VINDCDCx still needs to be connected to
the Vcc rail along with supply input of the other step-down converters. It is recommended to close the control
loop such that an inductor and output capacitor is added in the same way as it would be when operated
normally. If one of the LDOs is not used, its output capacitor should be added as well. If both LDOs are not used,
the input supply pin as well as the output pins of the LDOs (VINLDO, VLDO1, VLDO2) should be tied to GND.
42
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
Typical Configuration for the Texas Instruments® TMS320DM644x DaVinci Processors
Reset Condition of DCDC1
If DEFDCDC1 is connected to ground and DCDC1_EN is pulled high after VINDCDC1 is applied, the output
voltage of DCDC1 defaults to 1.225V instead of 1.2V (high by 2%). Figure 37 illustrates the problem.
VCC/VINDCDC1
DCDC1_EN
1.225 V
1.225 V
1.225 V
VDCDC1
Figure 37. Default DCDC1
Workaround 1: Tie DCDC1_EN to VINDCDC1 (Figure 38)
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
43
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
VCC/VINDCDC1
DCDC1_EN
1.20 V
1.20 V
1.20 V
VDCDC1
Figure 38. Workaround 1
Workaround 2: Write the correct voltage to the DEF_CORE register via I2C. This can be done before or after the
converter is enabled. If written before the enable, the only bit changed is DEF_CORE[0]. The voltage will be
1.2V, however, when the enable is pulled high (Figure 39).
VCC/VINDCDC1
DCDC1_EN
I2C Bus
DEF_CORE
VDCDC1
??
??
0x1F
0x1F 0x1E
0x10
0x11
1.225 V
0x10
1.20 V
1.20 V
Write DEF_CORE to 0x10
Pull DCDC1_EN High
Pull DCDC1_EN High
Write DEF_CORE to 0x10
Write CON_CTRL [7] to 1
Figure 39. Workaround 2
Workaround 3: Generate a HOT_RESET after enabling DCDC1 (Figure 40)
VCC/VINDCDC1
DCDC1_EN
HOT_RESET
1.225 V
1.20 V
1.225 V
1.20 V
VDCDC1
Figure 40. Workaround 3
44
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
CHANGES OF TPS65023B VERSUS TPS65023
ITEM
DESCRIPTION
Reference
TPS65023
TPS65023B
Minimum 1.69V;
Vcc = 2.5V to 5.25V
Minimum 1.55V;
VIH
High level input voltage for the SDAT pin
Minimum 1.3V
Vcc = 2.5V to 4.5V
ELECTRICAL
CHARACTERISTICS
Minimum 1.4V;
Vcc = 2.5V to 5.25V
VIH
VIL
High level input voltage for the SCLK pin
Minimum 1.3V
Maximum 0.4V
Low level input voltage for SCLK and
SDAT pin
Maximum 0.35V
th(DATA)
Data input hold time
Data input setup time
Minimum 300ns
Minimum 300ns
Minimum 100ns
Minimum 100ns
Table 4
tsu(DATA)
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
45
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
www.ti.com
REVISION HISTORY
Changes from Original (May 2006) to Revision A
Page
•
•
•
•
Changed VDCDC1 STEP-DOWN CONVERTER Electrical Characteristics ........................................................................ 7
Changed VDCDC3 STEP-DOWN CONVERTER Electrical Characteristics ........................................................................ 9
Changed CON_CTRL Register Address - Column B0 default value changed from 1 to 0. ............................................... 34
Changed VDCDC# to VDCDC1 .......................................................................................................................................... 36
Changes from Revision A (June 2006) to Revision B
Page
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Changed from: 1.5A and 97% Efficient Step-Down to: 1.7A and 90% Efficient Step-Down ................................................ 1
Changed from: 6 mm × 6 mm QFN Package to: 5 mm × 5 mm QFN Package ................................................................... 1
Changed from: RHA package to: RSB package ................................................................................................................... 1
Changed from:O(DCDC2) to: IO(DCDC1) ........................................................................................................................................ 3
Changed Forward current limit - removed TBD and added values ...................................................................................... 7
Changed Fixed output voltage - removed TBD and added values ....................................................................................... 7
Changed Fixed output voltage - removed TBD and added values ....................................................................................... 8
Added VINDCDC3 = 3.6 V to Maximum output current ....................................................................................................... 9
Changed Fixed output voltage - removed TBD and added values ....................................................................................... 9
Changed Figure 7 (Graph - DCDC2: OUTPUT VOLTAGE) ............................................................................................... 16
Added Figure 8 (Graph - DCDC3: OUTPUT VOLTAGE ) .................................................................................................. 16
Changed Figure 16 (Graph - VDCDC2 OUTPUT VOLTAGE RIPPLE) .............................................................................. 18
Changed Figure 29 (DVS Timing) ...................................................................................................................................... 28
Changed from: TPS65023 typically use a 3.3 μH output inductor to: TPS65023 typically use a 2.2 μH output
inductor ............................................................................................................................................................................... 38
•
•
•
•
•
Changed from: VDCDC3 to: VDCDC1 ............................................................................................................................... 40
Changed from: VDEFDCDC3 to: DEFDCDC1 ................................................................................................................... 40
Changed from: 2.5 V to 3.3 V (Table 7) ............................................................................................................................. 40
Changed Typical Configuration for Ti DaVinci Processors ................................................................................................. 43
Added Reset Condition of DCDC1 Information .................................................................................................................. 43
Changes from Revision B (June 2006) to Revision C
Page
•
•
Changed from: AD Coupled to: AD Coupled - Figure 12 ................................................................................................... 17
Changed from: AD Coupled to: AD Coupled - Figure 13 ................................................................................................... 17
Changes from Revision C (October 2006) to Revision D
Page
•
Changed Typical Configuration for Ti DaVinci Processors ................................................................................................. 43
Changes from Revision D (December 2006) to Revision E
Page
•
•
Changed LDO1 output voltage range from: 3.3 to: 3.3 ...................................................................................................... 10
Changed text string from: "VDCDC2 converter defaults to 1.8 V or 2.5 V" to: "VDCDC2 converter defaults to 1.8 V
or 3.3 V" .............................................................................................................................................................................. 22
46
Submit Documentation Feedback
Copyright © 2006–2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65023 TPS65023B
TPS65023, TPS65023B
www.ti.com
SLVS670J –JUNE 2006–REVISED SEPTEMBER 2011
Changes from Revision E (January 2007) to Revision F
Page
•
Changed text string from: "If it is tied to VCC, the default is 2.5 V" To: "If it is tied to VCC, the default is 3.3 V" ............. 22
Changes from Revision F (July 2007) to Revision G
Page
•
Changed the Interrupt Management and the INT Pin section. ........................................................................................... 26
Changes from Revision G (October 2008) to Revision H
Page
•
•
•
•
•
•
•
•
•
•
Changed IO(DCDC1) MAX from: 1500 mA to: 1700 mA ............................................................................................................ 3
Added High level input voltage for the SDAT pin ................................................................................................................. 4
Changed IO from:1500 mA MIN to 1700 mA ........................................................................................................................ 7
Changed IO maximum from:1.5 A to: 1.7 A for VDCDC1 fixed and adjustable output voltage test condition specs. .......... 7
Changed IO maximum from: 1500 mA to: 1700 mA for VDCDC1 Load Regulation test condition ....................................... 7
Changed VDCDC1 "Soft start ramp time" spec to: "tStart and tRamp" specifications with MIN TYP MAX values. .................. 7
Changed VDCDC2 "Soft start ramp time" spec To: "tStart and tRamp" specifications with MIN TYP MAX values. ................. 8
Changed VDCDC3 "Soft start ramp time" spec To: "tStart and tRamp" specifications with MIN TYP MAX values. ................. 9
Changed FBD graphic to show 1700 mA for DCDC1 Buck Converter .............................................................................. 13
Changed text string from: "1.2 V or 1.8 V" to: "1.2 V to 1.6 V" in the STEP-DOWN CONVERTERS.,VDCDC1....
description. .......................................................................................................................................................................... 22
•
•
•
Changed th(DATA) MIN spec from 0 ns to 300 ns .................................................................................................................. 31
Changed tsu(DATA) MIN spec from 100 ns to 300 ns ............................................................................................................ 31
Changed graphic entity to the one used in the Application Note SLVA273 ....................................................................... 43
Changes from Revision H (December 2009) to Revision I
Page
•
•
•
•
•
•
•
Added I2C Compatible Serial Interface to Features list ........................................................................................................ 1
Added TPS65023B device specs ......................................................................................................................................... 1
Added ordering info for TPS65023B device ......................................................................................................................... 2
Added specs for TPS65023B device .................................................................................................................................... 4
Changed "VBACKUP threshold" test condition typographical error from "VBACKUP falling" to "VBACKUP rising" ........... 6
Added specs for TPS65023B device .................................................................................................................................. 31
Added Differences table for TPS65023 and TPS65023B devices ..................................................................................... 45
Changes from Revision I (July 2010) to Revision J
Page
•
Added Thermal Information Table and deleted Dissipation Ratings Table .......................................................................... 2
Copyright © 2006–2011, Texas Instruments Incorporated
Submit Documentation Feedback
47
Product Folder Link(s) :TPS65023 TPS65023B
PACKAGE OPTION ADDENDUM
www.ti.com
19-Sep-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS65023BRSBR
TPS65023BRSBT
TPS65023RSBR
TPS65023RSBRG4
TPS65023RSBT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
WQFN
WQFN
WQFN
WQFN
WQFN
WQFN
RSB
RSB
RSB
RSB
RSB
RSB
40
40
40
40
40
40
3000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
3000
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS65023RSBTG4
250
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Sep-2012
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS65023 :
Automotive: TPS65023-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS65023BRSBR
TPS65023BRSBT
TPS65023RSBR
TPS65023RSBT
WQFN
WQFN
WQFN
WQFN
RSB
RSB
RSB
RSB
40
40
40
40
3000
250
330.0
180.0
330.0
180.0
12.4
12.4
12.4
12.4
5.3
5.3
5.3
5.3
5.3
5.3
5.3
5.3
1.5
1.5
1.5
1.5
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
Q2
Q2
Q2
Q2
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS65023BRSBR
TPS65023BRSBT
TPS65023RSBR
TPS65023RSBT
WQFN
WQFN
WQFN
WQFN
RSB
RSB
RSB
RSB
40
40
40
40
3000
250
367.0
210.0
367.0
210.0
367.0
185.0
367.0
185.0
35.0
35.0
35.0
35.0
3000
250
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明