TPS76618DG4 [TI]
ULTRALOW QUIESCENT CURRENT 250-mA LOW DROPOUT VOLTAGE REGULATORS; 超低静态电流250 mA低压差稳压器
| 型号： | TPS76618DG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | ULTRALOW QUIESCENT CURRENT 250-mA LOW DROPOUT VOLTAGE REGULATORS |
| 文件： | 总24页 (文件大小：1357K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
ULTRALOW QUIESCENT CURRENT 250-mA
LOW DROPOUT VOLTAGE REGULATORS
Because the PMOS device behaves as a low-value
resistor, the dropout voltage is very low (typically 230
1
FEATURES
2
•
250-mA Low Dropout Voltage Regulator
mV at an output current of 250 mA for the TPS76650)
and is directly proportional to the output current.
Additionally, since the PMOS pass element is a
voltage-driven device, the quiescent current is very
low and independent of output loading (typically 35
µA over the full range of output current, 0 mA to 250
mA). These two key specifications yield a significant
improvement in operating life for battery-powered
systems. This LDO family also features a sleep
mode; applying a TTL high signal to EN (enable)
shuts down the regulator, reducing the quiescent
current to less than 1 µA (typ).
•
Available in 1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V,
3.0 V, 3.3 V, 5.0 V Fixed Output and Adjustable
Versions
•
Dropout Voltage to 140 mV (Typ) at 250 mA
(TPS76650)
•
•
Ultralow 35-µA Typical Quiescent Current
3% Tolerance Over Specified Conditions for
Fixed Output Versions
•
•
•
Open-Drain Power Good
8-Pin SOIC Package
Power good (PG) is an active high output that can be
used to implement a power-on reset or a low-battery
indicator.
Thermal Shutdown Protection
DESCRIPTION
The TPS766xx is offered in 1.5 V, 1.8 V, 2.5 V, 2.7 V,
2.8 V, 3.0 V, 3.3 V and 5.0 V fixed voltage versions
and in an adjustable version (programmable over the
range of 1.25 V to 5.5 V). Output voltage tolerance is
specified as a maximum of 3% over line, load, and
temperature ranges. The TPS766xx family is
available in an 8-pin SOIC package.
This device is designed to have an ultralow quiescent
current and be stable with a 4.7-µF capacitor. This
combination provides high performance at
reasonable cost.
a
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2009, Texas Instruments Incorporated
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
(2)
PRODUCT
VOUT
XX is nominal output voltage (for example, 28 = 2.8V, 01 = Adjustable).(3)
Y is package designator.
TPS766xxyz
Z is package quantity.
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
(2) Output voltages from 1.5 V to 5.0 V in 50-mV increments are available through the use of innovative factory EEPROM programming;
minimum order quantities may apply. Contact factory for details and availability.
(3) The TPS76601 is programmable using an external resistor divider (see Application Information).
ABSOLUTE MAXIMUM RATINGS
Over operating free-air temperature range (unless otherwise noted).(1)
PARAMETER
TPS766xx
UNIT
VI
Input voltage range(2)
–0.3 to 13.5
V
V
V
Voltage range at EN
–0.3 to 16.5
Maximum PG voltage
16.5
Peak output current
Internally limited
Continuous total power dissipation
Output voltage (OUT, FB)
Operating virtual junction temperature range
Storage temperature range
ESD rating, HBM
See Dissipation Ratings Table
VO
TJ
7
V
–40 to +125
–65 to +150
2
°C
°C
kV
Tstg
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
(2) All voltage values are with respect to network terminal ground.
DISSIPATION RATINGS
AIR FLOW
(CFM)
TA < +25°C
POWER RATING
DERATING FACTOR
ABOVE TA = +25°C
TA = +70°C
POWER RATING
TA = +85°C
POWER RATING
PACKAGE
0
568 mW
904 mW
5.68 mW/°C
9.04 mW/°C
312 mW
497 mW
227 mW
361 mW
D
250
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
10
UNIT
V
VI
Input voltage(1)
2.7
1.2
0
VO
IO
Output voltage range
Output current(2)
5.5
V
250
125
mA
°C
TJ
Operating virtual junction temperature(2)
–40
VI(min) = VO(max) + VDO(max load)
(1) To calculate the minimum input voltage for your maximum output current, use the following equation:
(2) Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
2
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
ELECTRICAL CHARACTERISTICS
Over recommended operating free-air temperature range, Vi = VO(typ) + 1 V, IO = 10 µA, EN = 0 V, CO = 4.7 µF (unless
otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1.03 VO
1.545
1.854
2.575
2.781
2.884
3.090
3.399
5.150
50
UNIT
5.5 V ≥ VO ≥ 1.25 V,
5.5 V ≥ VO ≥ 1.25 V,
TJ = +25°C,
TJ = +25°C
VO
TPS76601
TPS76615
TPS76618
TPS76625
TPS76627
TPS76628
TPS76630
TPS76633
TPS76650
TJ = –40°C to +125°C 0.97 VO
2.7 V < VIN < 10 V
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
35
TJ = –40°C to +125°C,
TJ = +25°C,
2.7 V < VIN < 10 V
2.8 V < VIN < 10 V
2.8 V < VIN < 10 V
3.5 V < VIN < 10 V
3.5 V < VIN < 10 V
3.7 V < VIN < 10 V
3.7 V < VIN < 10 V
3.8 V < VIN < 10 V
3.8 V < VIN < 10 V
4.0 V < VIN < 10 V
4.0 V < VIN < 10 V
4.3 V < VIN < 10 V
4.3 V < VIN < 10 V
6.0 V < VIN < 10 V
6.0 V < VIN < 10 V
TJ = +25°C
1.455
1.746
2.425
2.619
2.716
2.910
3.201
4.850
TJ = –40°C to +125°C,
TJ = +25°C,
TJ = –40°C to +125°C,
TJ = +25°C,
Output voltage
(10 µA to 250 mA load)(1)
V
TJ = –40°C to +125°C,
TJ = +25°C,
TJ = –40°C to +125°C,
TJ = +25°C,
TJ = –40°C to +125°C,
TJ = +25°C,
TJ = –40°C to +125°C,
TJ = +25°C,
TJ = –40°C to +125°C,
10 µA < IO < 250 mA,
IO = 250 mA,
Quiescent current (GND current) EN = 0 V(1)
µA
TJ = –40°C to +125°C
TJ = +25°C
Output voltage line regulation (ΔVO/VO)(1),(2)
VO + 1 V < VI ≤ 10 V,
IO = 10 µA to 250 mA
BW = 300 Hz to 50 kHz,
CO = 4.7 µF,
0.01
%/V
Load regulation
0.5%
Output noise voltage
200
µVrms
TJ = +25°C
Output current limit
VO = 0 V
0.8
1.2
A
Thermal shutdown junction temperature
150
°C
TJ = +25°C
2.7 V < VI < 10 V
EN = VI,
1
µA
µA
Standby current
TJ = –40°C to +125°C
2.7 V < VI < 10 V
EN = VI,
10
FB input current
TPS76601
FB = 1.5 V
2
nA
V
High level enable input voltage
Low level enable input voltage
2.0
0.8
V
f = 1 kHz,
IO = 10 µA,
CO = 4.7 µF,
TJ = +25°C
Power-supply ripple rejection(1)
63
dB
(1) Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum IN voltage 10 V.
(2) If VO ≥ 1.8 V then Vimin = 2.7 V, Vimax = 10 V:
VO(Vimax - 2.7 V)
Line Reg. (mV) = (%/V) ´
´ 1000
100
If VO ≤ 2.5 V then Vimin = VO + 1 V, Vimax = 10 V:
VO(Vimax - (VO + 1 V))
Line Reg. (mV) = (%/V) ´
´ 1000
100
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Over recommended operating free-air temperature range, Vi = VO(typ) + 1 V, IO = 10 µA, EN = 0 V, CO = 4.7 µF (unless
otherwise noted).
PARAMETER
Minimum input voltage for valid PG
Trip threshold voltage
Hysteresis voltage
TEST CONDITIONS
IO(PG) = 300 µA
MIN
TYP
MAX
UNIT
1.1
VO decreasing
Measured at VO
VI = 2.7 V,
92
98
%VO
%VO
V
PG
0.5
Output low voltage
IO(PG) = 1 mA
0.15
0.4
1
Leakage current
V(PG) = 5 V
µA
EN = 0 V
–1
–1
0
310
270
230
140
1
Input current (EN)
µA
EN = VI
1
IO = 250 mA,
IO = 250 mA,
IO = 250 mA,
IO = 250 mA,
IO = 250 mA,
IO = 250 mA,
IO = 250 mA,
IO = 250 mA,
TJ = +25°C
TPS76628
TPS76630
TPS76633
TPS76650
TJ = –40°C to +125°C
TJ = +25°C
540
470
400
250
TJ = –40°C to +125°C
TJ = +25°C
(3)
Dropout voltage
mV
TJ = –40°C to +125°C
TJ = +25°C
TJ = –40°C to +125°C
(3) IN voltage equals VO(Typ) – 100 mV; TPS76601 output voltage set to 3.3 V nominal with external resistor divider. TPS76615, TPS76618,
TPS76625, and TPS76627 dropout voltage limited by input voltage range limitations (that is, TPS76630 input voltage must drop to 2.9 V
for purpose of this test).
(1)
CO
(1) See Applications Information section for capacitor selection details.
Figure 1. Typical Application Configuration for Fixed Output Options
4
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
FUNCTIONAL BLOCK DIAGRAM—ADJUSTABLE VERSION
FUNCTIONAL BLOCK DIAGRAM—FIXED-VOLTAGE VERSION
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
D PACKAGE
SOIC-8
(TOP VIEW)
NC/FB
PG
1
2
3
4
8
7
6
5
OUT
OUT
IN
GND
EN
IN
PIN DESCRIPTIONS
TPS766xx
NAME NO.
EN
I/O
DESCRIPTION
4
1
I
I
Enable input.
FB/NC
GND
IN
Feedback input voltage for adjustable device (not connected for fixed options).
3
Regulator ground.
Input voltage.
5, 6
7, 8
2
I
OUT
PG
O
O
Regulated output voltage.
Power good output.
Table 1. Table of Graphs
FIGURE
Figure 2, Figure 3
Figure 4, Figure 5
Figure 6, Figure 7
Figure 8, Figure 9
Figure 10
vs Load current
Output voltage
Ground current
vs Free-air temperature
vs Load current
vs Free-air temperature
vs Frequency
Power-supply ripple rejection
Output spectral noise density
Output impedance
vs Frequency
Figure 11
vs Frequency
Figure 12
Dropout voltage
vs Free-air temperature
Figure 13, Figure 14
Figure 15, Figure 17
Figure 16, Figure 18
Figure 19
Line transient response
Load transient response
Output voltage
vs Time
Dropout voltage
vs Input voltage
Figure 20
Equivalent series resistance (ESR)
Equivalent series resistance (ESR)
vs Output current
vs Added ceramic capacitance
Figure 21 to Figure 24
Figure 25, Figure 26
6
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
TYPICAL CHARACTERISTICS
TPS76633
OUTPUT VOLTAGE
vs
TPS76615
OUTPUT VOLTAGE
vs
LOAD CURRENT
LOAD CURRENT
Figure 2.
Figure 3.
TPS76633
OUTPUT VOLTAGE
vs
TPS76615
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
Figure 4.
Figure 5.
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
TPS76633
GROUND CURRENT
vs
TPS76615
GROUND CURRENT
vs
LOAD CURRENT
LOAD CURRENT
Figure 6.
Figure 7.
TPS76633
GROUND CURRENT
vs
TPS76615
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
Figure 8.
Figure 9.
8
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
TYPICAL CHARACTERISTICS (continued)
TPS76633
TPS76633
POWER-SUPPLY RIPPLE REJECTION
OUTPUT SPECTRAL NOISE DENSITY
vs
vs
FREQUENCY
FREQUENCY
Figure 10.
Figure 11.
TPS76633
OUTPUT IMPEDANCE
vs
TPS76650
DROPOUT VOLTAGE
vs
FREQUENCY
FREE-AIR TEMPEATURE
Figure 12.
Figure 13.
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
TPS76633
DROPOUT VOLTAGE
vs
TPS76615
LINE TRANSIENT RESPONSE
FREE-AIR TEMPEATURE
Figure 14.
Figure 15.
TPS76633
LOAD TRANSIENT RESPONSE
TPS76633
LINE TRANSIENT RESPONSE
Figure 16.
Figure 17.
10
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
TYPICAL CHARACTERISTICS (continued)
TPS76633
OUTPUT VOLTAGE
TPS76633
LOAD TRANSIENT RESPONSE
vs
TIME (AT STARTUP)
Figure 18.
Figure 19.
TPS76601
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
Figure 20.
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
OUTPUT CURRENT
OUTPUT CURRENT
Figure 21.
Figure 22.
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
OUTPUT CURRENT
OUTPUT CURRENT
Figure 23.
Figure 24.
(1) Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any
series resistance added externally, and PWB trace resistance to CO.
12
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
TYPICAL CHARACTERISTICS (continued)
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
ADDED CERAMIC CAPACITANCE
ADDED CERAMIC CAPACITANCE
Figure 25.
Figure 26.
(1) Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any
series resistance added externally, and PWB trace resistance to CO.
Figure 27. Test Circuit for Typical Regions of Stability (Figure 21 through Figure 24) (Fixed Output
Options)
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
APPLICATION INFORMATION
The TPS766xx family includes eight fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V,
3.3 V, and 5.0 V), and an adjustable regulator, the TPS76601 (adjustable from 1.25 V to 5.5 V).
DEVICE OPERATION
The TPS766xx features very low quiescent current that remains virtually constant even with varying loads.
Conventional LDO regulators use a pnp pass element, the base current of which is directly proportional to the
load current through the regulator (IB = IC/β). The TPS766xx uses a PMOS transistor to pass current; because
the gate of the PMOS is voltage driven, operating current is low and invariable over the full load range.
Another pitfall associated with the pnp pass element is its tendency to saturate when the device goes into
dropout. The resulting drop in β forces an increase in IB to maintain the load. During power up, this increase in IB
translates to large start-up currents. Systems with limited supply current may fail to start up. In battery-powered
systems, it means rapid battery discharge when the voltage decays below the minimum required for regulation.
The TPS766xx quiescent current remains low even when the regulator drops out, eliminating both problems.
The TPS766xx family also features a shutdown mode that places the output in the high-impedance state
(essentially equal to the feedback-divider resistance) and reduces quiescent current to 1 µA (typ). If the
shutdown feature is not used, EN should be tied to ground. Response to an enable transition is quick; regulated
output voltage is reestablished in typically 160 µs.
MINIMUM LOAD REQUIREMENTS
The TPS766xx family is stable even at zero load; no minimum load is required for operation.
FB—PIN CONNECTION (ADJUSTABLE VERSION ONLY)
The FB pin is an input pin to sense the output voltage and close the loop for the adjustable option. The output
voltage is sensed through a resistor divider network to close the loop as shown in Figure 29. Normally, this
connection should be as short as possible; however, the connection can be made near a critical circuit to
improve performance at that point. Internally, FB connects to a high-impedance, wide-bandwidth amplifier and
noise pickup feeds through to the regulator output. Routing the FB connection to minimize or avoid noise pickup
is essential.
EXTERNAL CAPACITOR REQUIREMENTS
An input capacitor is not usually required; however, a ceramic bypass capacitor (0.047 µF or larger) improves
load transient response and noise rejection if the TPS766xx is located more than a few inches from the power
supply. A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Like most low dropout regulators, the TPS766xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance value is 4.7 µF and the ESR
(equivalent series resistance) must be between 300 mW and 20 Ω. Capacitor values 4.7 µF or larger are
acceptable, provided the ESR is less than 20 Ω. Solid tantalum electrolytic and aluminum electrolytic capacitors
are all suitable, provided they meet the requirements described previously. Ceramic capacitors, with series
resistors that are sized to meet the previously described requirements, may also be used.
14
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
www.ti.com................................................................................................................................................. SLVS237C–AUGUST 1999–REVISED JANUARY 2009
Figure 28. Typical Application Circuit (Fixed Versions)
PROGRAMMING THE TPS76601 ADJUSTABLE LDO REGULATOR
The output voltage of the TPS76601 adjustable regulator is programmed using an external resistor divider as
shown in Figure 29. The output voltage is calculated using:
(1)
Where:
•
Vref = 1.224 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 7-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided because leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose R2 = 169 kΩ
to set the divider current at 7 µA, and then calculate R1 using:
(2)
Figure 29. TPS76601 Adjustable LDO Regulator Programming
Copyright © 1999–2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
TPS76615, TPS76618, TPS76625
TPS76627, TPS76628, TPS76630
TPS76633, TPS76650, TPS76601
SLVS237C–AUGUST 1999–REVISED JANUARY 2009................................................................................................................................................. www.ti.com
POWER-GOOD INDICATOR
The TPS766xx features a power-good (PG) output that can be used to monitor the status of the regulator. The
internal comparator monitors the output voltage: when the output drops to between 92% and 98% of its nominal
regulated value, the PG output transistor turns on, taking the signal low. The open-drain output requires a pullup
resistor. If not used, it can be left floating. PG can be used to drive power-on reset circuitry or used as a
low-battery indicator.
REGULATOR PROTECTION
The TPS766xx PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (for example, during power down). Current is conducted from the output
to the input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The TPS766xx also features internal current limiting and thermal protection. During normal operation, the
TPS766xx limits output current to approximately 0.8 A (typ). When current limiting engages, the output voltage
scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross
device failure, care should be taken not to exceed the power dissipation ratings of the package. If the
temperature of the device exceeds +150°C (typ), thermal-protection circuitry shuts it down. Once the device has
cooled below +130°C (typ), regulator operation resumes.
POWER DISSIPATION AND JUNCTION TEMPERATURE
Specified regulator operation is assured to a junction temperature of +125°C; the maximum junction temperature
should be restricted to +125°C under normal operating conditions. This restriction limits the power dissipation the
regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or
equal to PD(max)
.
The maximum-power-dissipation limit is determined using the following equation:
(3)
Where:
•
•
TJmax is the maximum allowable junction temperature;
θJA is the thermal resistance junction-to-ambient for the package (that is, 176°C/W for the 8-terminal SOIC);
R
and
•
TA is the ambient temperature.
The regulator dissipation is calculated using:
(4)
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation triggers the thermal
protection circuit.
16
Submit Documentation Feedback
Copyright © 1999–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
TPS76601D
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
76601
TPS76601DG4
TPS76601DR
TPS76601DRG4
TPS76615D
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
75
2500
2500
75
Green (RoHS
& no Sb/Br)
76601
76601
76601
76615
76615
76615
76615
76618
76618
76618
76618
76625
76625
76625
76625
76628
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS76615DG4
TPS76615DR
TPS76615DRG4
TPS76618D
75
Green (RoHS
& no Sb/Br)
2500
2500
75
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS76618DG4
TPS76618DR
TPS76618DRG4
TPS76625D
75
Green (RoHS
& no Sb/Br)
2500
2500
75
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS76625DG4
TPS76625DR
TPS76625DRG4
TPS76628D
75
Green (RoHS
& no Sb/Br)
2500
2500
75
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
TPS76628DG4
TPS76628DR
TPS76628DRG4
TPS76630D
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
8
8
8
8
8
8
8
8
8
8
8
8
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
76628
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
D
D
D
D
D
D
D
D
D
D
2500
2500
75
Green (RoHS
& no Sb/Br)
76628
76628
76630
76630
76633
76633
76633
76633
76650
76650
76650
76650
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS76630DG4
TPS76633D
75
Green (RoHS
& no Sb/Br)
75
Green (RoHS
& no Sb/Br)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
TPS76633DG4
TPS76633DR
TPS76633DRG4
TPS76650D
75
Green (RoHS
& no Sb/Br)
2500
2500
75
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS76650DG4
TPS76650DR
TPS76650DRG4
75
Green (RoHS
& no Sb/Br)
2500
2500
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS76601DR
TPS76615DR
TPS76618DR
TPS76625DR
TPS76628DR
TPS76633DR
TPS76633DR
TPS76650DR
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
D
D
8
8
8
8
8
8
8
8
2500
2500
2500
2500
2500
2500
2500
2500
330.0
330.0
330.0
330.0
330.0
330.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
5.2
5.2
5.2
5.2
5.2
5.2
5.2
5.2
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS76601DR
TPS76615DR
TPS76618DR
TPS76625DR
TPS76628DR
TPS76633DR
TPS76633DR
TPS76650DR
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
D
D
8
8
8
8
8
8
8
8
2500
2500
2500
2500
2500
2500
2500
2500
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
TPS76618PWR
IC VREG 1.8 V FIXED POSITIVE LDO REGULATOR, PDSO8, Fixed Positive Single Output LDO Regulator
TI
©2020 ICPDF网 联系我们和版权申明