TPS77115DGK [TI]
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING; 150 - mA的8引脚MSOP封装的LDO稳压器型号: | TPS77115DGK |
厂家: | TEXAS INSTRUMENTS |
描述: | 150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING |
文件: | 总25页 (文件大小:352K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
D
D
Open Drain Power-On Reset With 220-ms
Delay (TPS771xx)
TPS771xx
DGK Package
(TOP VIEW)
Open Drain Power-Good (PG) Status
Output (TPS772xx)
FB/SENSE
RESET
EN
8
7
6
5
OUT
OUT
IN
1
2
3
4
D
150-mA Low-Dropout Voltage Regulator
D
Available in 1.5-V, 1.8-V, 2.7-V, 2.8-V, 3.3-V,
5.0-V Fixed Output and Adjustable Versions
GND
IN
D
D
D
D
Dropout Voltage Typically 115 mV
at 150 mA (TPS77133, TPS77233)
TPS772xx
DGK Package
(TOP VIEW)
Ultralow 92-µA Quiescent Current (Typ)
8-Pin MSOP (DGK) Package
FB/SENSE
PG
OUT
OUT
IN
1
2
3
4
8
7
6
5
Low Noise (55 µV
) Without External
rms
Filter (Bypass) Capacitor (TPS77118,
TPS77218)
EN
GND
IN
D
2% Tolerance Over Specified Conditions
for Fixed-Output Versions
TPS77x33
D
Fast Transient Response
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
D
Thermal Shutdown Protection
300
description
250
200
150
100
50
The TPS771xx and TPS772xx are low-dropout
regulators with integrated power-on reset and
power good (PG) function respectively. These
devicesarecapableofsupplying150mAofoutput
current with a dropout of 115 mV (TPS77133,
TPS77233). Quiescent current is 92 µA at full load
dropping down to 1 µA when device is disabled.
These devices are optimized to be stable with a
wide range of output capacitors including lowESR
ceramic (10 µF) or low capacitance (1 µF)
tantalum capacitors. These devices have ex-
I
= 150 mA
O
I
= 10 mA
O
I
O
= 0 A
tremely low noise output performance (55 µV
)
rms
0
without using any added filter capacitors.
TPS771xx and TPS772xx are designed to have
fast transient response for larger load current
changes.
–50
–40
0
40
80
120
160
T
J
– Junction Temperature – °C
The TPS771xx or TPS772xx is offered in 1.5 V,
1.8-V, 2.7-V, 2.8-V, 3.3-V, and 5.0 V fixed-voltage versions and in an adjustable version (programmable over
the range of 1.5 V to 5.5 V). Output voltage tolerance is 2% over line, load, and temperature ranges. The
TPS771xx and TPS772xx families are available in 8-pin MSOP (DGK) packages.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 115 mV
at an output current of 150 mA for 3.3 volt option) and is directly proportional to the output current. Additionally,
since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent
of output loading (typically 92 µA over the full range of output current, 0 mA to 150 mA). These two key
specifications yield a significant improvement in operating life for battery-powered systems.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
description (continued)
The device is enabled when the EN pin is connected to a low-level input voltage. This LDO family also features
a sleep mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent
current to less than 1 µA at T = 25°C.
J
The TPS771xx features an integrated power-on reset, commonly used as a supply voltage supervisor (SVS)
or reset output voltage. The RESET output of the TPS771xx initiates a reset in DSP, microcomputer or
microprocessor systems at power up and in the event of an undervoltage condition. An internal comparator in
the TPS771xx monitors the output voltage of the regulator to detect an undervoltage condition on the regulated
output voltage. When OUT reaches 95% of its regulated voltage, RESET will go to a high-impedance state after
a 220 ms delay. RESET will go to low-impedance state when OUT is pulled below 95% (i.e. over load condition)
of its regulated voltage.
For the TPS772xx, the power good terminal (PG) is an active high output, which can be used to implement a
power-on reset or a low-battery indicator. An internal comparator in the TPS772xx monitors the output voltage
of the regulator to detect an undervoltage condition on the regulated output voltage. When OUTfalls below 82%
of its regulated voltage, PG will go to a low-impedance state. PG will go to a high-impedance state when OUT
is above 82% of its regulated voltage.
AVAILABLE OPTIONS
OUTPUT VOLTAGE
(V)
PACKAGED DEVICES
MSOP (DGK)
T
J
TPS771xx
SYMBOL
TPS772xx
SYMBOL
TYP
5.0
3.3
2.8
2.7
1.8
1.5
TPS77150DGK
TPS77133DGK
TPS77128DGK
TPS77127DGK
TPS77118DGK
TPS77115DGK
AFV
AFU
AFS
AFR
AFP
AFO
TPS77250DGK
AGE
AGD
AGB
AGA
AFY
AFX
TPS77233DGK
TPS77228DGK
TPS77227DGK
TPS77218DGK
TPS77215DGK
–40°C to 125°C
Adjustable
1.5 V to 5.5 V
TPS77101DGK
AFN
TPS77201DGK
AFW
NOTE: The TPS77101 and TPS77201 are programmable using an external resistor divider (see application information).
The DGK package is available taped and reeled. Add an R suffix to the device type (e.g., TPS77101DGKR).
5
6
7
8
1
V
I
IN
IN
OUT
OUT
V
O
SENSE
3
0.1 µF
2
PG or
RESET
EN
PG or RESET
10 µF
+
GND
4
Figure 1. Typical Application Configuration (For Fixed Output Options)
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
functional block diagrams
adjustable version
IN
EN
PG or RESET
OUT
_
+
+
_
220 ms Delay
(for TPS771xx Option)
R1
R2
V
ref
= 1.1834 V
FB/SENSE
GND
External to the Device
fixed-voltage version
IN
EN
PG or RESET
_
+
OUT
SENSE
+
_
220 ms Delay
(for TPS771xx Option)
R1
R2
V
ref
= 1.1834 V
GND
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
TPS771XX
FB/SENSE
RESET
EN
NO.
1
2
I
O
I
Feedback input voltage for adjustable device (sense input for fixed options)
Reset output
3
Enable input
GND
4
Regulator ground
Input voltage
IN
5, 6
7, 8
I
OUT
O
Regulated output voltage
TPS772XX
FB/SENSE
PG
1
2
I
O
I
Feedback input voltage for adjustable device (sense input for fixed options)
Power good
EN
3
Enable input
GND
4
Regulator ground
Input voltage
IN
5, 6
7, 8
I
OUT
O
Regulated output voltage
TPS771xx RESET timing diagram
V
I
†
V
res
†
V
res
t
‡
‡
V
O
V
IT+
V
IT+
Threshold
Voltage
‡
‡
V
IT–
V
IT–
t
RESET
Output
220 ms
Delay
220 ms
Delay
Output
Undefined
Output
Undefined
t
†
‡
V
is the minimum input voltage for a valid RESET. The symbol V is not currently listed within EIA or JEDEC standards for
res
res
semiconductor symbology.
– Trip voltage is typically 5% lower than the output voltage (95%V ) V
V
to V
is the hysteresis voltage.
IT+
IT
O
IT–
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TPS772xx PG timing diagram
V
I
†
V
res
†
V
res
t
‡
‡
V
O
V
IT+
V
IT+
Threshold
Voltage
‡
‡
V
IT–
V
IT–
t
PG
Output
Output
Undefined
Output
Undefined
t
†
‡
V
is the minimum input voltage for a valid PG. The symbol V is not currently listed within EIA or JEDEC standards for semiconductor
res
res
symbology.
– Trip voltage is typically 18% lower than the output voltage (82%V ) V
V
to V
is the hysteresis voltage.
IT+
IT
O
IT–
Ĕ
absolute maximum ratings over operating junction temperature range (unless otherwise noted)
Input voltage range, V , (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 13.5 V
I
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 16.5 V
Maximum RESET voltage (TPS771xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Maximum PG voltage (TPS772xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Output voltage, V (OUT, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
O
Operating virtual junction temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 125°C
J
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network terminal ground.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
DISSIPATION RATING TABLE – FREE-AIR TEMPERATURES
AIR FLOW
(CFM)
θ
θ
T
< 25°C
DERATING FACTOR
T
= 70°C
T = 85°C
A
JA
JC
A
A
PACKAGE
(°C/W) (°C/W) POWER RATING
ABOVE T = 25°C
POWER RATING POWER RATING
A
0
266.2
255.2
242.8
3.84
3.92
4.21
376 mW
392 mW
412 mW
3.76 mW/°C
3.92 mW/°C
4.12 mW/°C
207 mW
216 mW
227 mW
150 mW
157 mW
165 mW
150
250
DGK
recommended operating conditions
MIN
2.7
1.5
0
MAX
UNIT
†
Input voltage, V
10
5.5
V
V
I
Output voltage range, V
O
Output current, I (see Note 2)
150
125
mA
°C
O
Operating virtual junction temperature, T (see Note 2)
–40
J
†
To calculate the minimum input voltage for your maximum output current, use the following equation: V
I(min)
= V
+ V
.
DO(max load)
O(max)
NOTE 2: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
electrical characteristics over recommended operating junction temperature range (–40°C to
125°C), V = V
+ 1 V, I = 1 mA, EN = 0 V, C = 10 µF (unless otherwise noted)
I
O(typ)
O
O
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1.5 V ≤ V ≤ 5.5 V,
T = 25°C
V
O
O
J
Adjustable voltage
1.5-V Output
1.8-V Output
2.7-V Output
2.8-V Output
3.3-V Output
5.0-V Output
V
1.5 V ≤ V ≤ 5.5 V
0.98V
1.02V
O
O
O
T = 25°C,
J
2.7 V < V < 10 V
IN
1.5
1.8
2.7 V < V < 10 V
IN
1.470
1.530
T = 25°C,
J
2.8 V < V < 10 V
IN
2.8 V < V < 10 V
IN
1.764
2.646
2.744
3.234
4.900
1.836
2.754
2.856
3.366
5.100
125
T = 25°C,
J
3.7 V < V < 10 V
IN
2.7
Output voltage
(see Notes 3 and 4)
V
3.7 V < V < 10 V
IN
T = 25°C,
J
3.8 V < V < 10 V
IN
2.8
3.8 V < V < 10 V
IN
T = 25°C,
J
4.3 V < V < 10 V
IN
3.3
4.3 V < V < 10 V
IN
T = 25°C,
J
6 V < V < 10 V
IN
5.0
V
6 V < V < 10 V
IN
T = 25°C
J
92
Quiescent current (GND current) (see Notes 3 and 4)
µA
V
V
+ 1 V < V ≤ 10 V, T = 25°C
0.005
%/V
%/V
mV
O
I
J
Output voltage line regulation (∆V /V ) (see Note 5)
O
O
+ 1 V < V ≤ 10 V
0.05
O
I
Load regulation
T = 25°C
J
1
BW = 300 Hz to 100 kHz, T = 25°C,
TPS77118, TPS77218
J
Output noise voltage
55
µVrms
Output current Limit
Peak output current
V
= 0 V
0.9
400
144
1.3
A
mA
°C
µA
µA
µA
V
O
2 ms pulse width,
50% duty cycle
Thermal shutdown junction temperature
EN = V
EN = V
T = 25°C
J
1
3
1
I,
I
Standby current
FB input current
Adjustable voltage
FB = 1.5 V
High level enable input voltage
Low level enable input voltage
Enable input current
2
0.7
1
V
–1
µA
dB
Power supply ripple rejection (TPS77118, TPS77218) f = 1 KHz,
T = 25°C
J
55
NOTES: 3. Minimum input operating voltage is 2.7 V or V
current 1 mA.
+ 1 V, whichever is greater. Maximum input voltage = 10 V, minimum output
O(typ)
4. If V < 1.8 V then V
I(max)
= 10 V, V
= 2.7 V:
O
I(min)
OǒVI(max) * 2.7 VǓ
1000
V
ǒ
Ǔ
Line regulation (mV) + %ńV
100
If V > 2.5 V then V
I(max)
= 10 V, V
= Vo + 1 V:
I(min)
O
* ǒVO
100
Ǔ
OǒVI(max)
) 1 Ǔ
V
ǒ
Ǔ
Line regulation (mV) + %ńV
1000
5.
I
O
= 1 mA to 150 mA
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
electrical characteristics over recommended operating junction temperature range (–40°C to
125°C), V = V
+ 1 V, I = 1 mA, EN = 0 V, C = 10 µF (unless otherwise noted) (continued)
I
O(typ)
O
O
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Minimum input voltage for valid PG
Trip threshold voltage
Hysteresis voltage
I
= 300µA
V
≤ 0.8 V
1.1
V
(PG)
(PG)
V
decreasing
79
85
%V
%V
V
O
O
PG
(TPS772xx)
Measured at V
0.5
O
O
Output low voltage
V = 2.7 V,
I
= 1mA
0.15
0.4
1
I
(PG)
Leakage current
V
= 5 V
µA
(PG)
Minimum input voltage for valid RESET
Trip threshold voltage
Hysteresis voltage
I
= 300 µA
1.1
V
(RESET)
V
decreasing
92
98
%V
%V
V
O
O
Measured at V
0.5
Reset
(TPS771xx)
O
O
Output low voltage
V = 2.7 V,
I
= 1 mA
0.15
0.4
1
I
(RESET)
Leakage current
V
= 5 V
µA
(RESET)
RESET time-out delay
220
150
ms
I
O
I
O
I
O
I
O
I
O
I
O
= 150 mA,
= 150 mA,
= 150 mA,
= 150 mA
= 150 mA,
= 150 mA
T = 25°C
J
2.8-V Output
265
200
115
T = 25°C
J
115
75
V
DO
Dropout voltage (see Note 6)
3.3-V Output
5.0-V Output
mV
T = 25°C
J
NOTE 6: IN voltage equals V (typ) – 100 mV; 1.5 V, 1.8 V, and 2.7 V dropout voltage limited by input voltage range limitations (i.e., 3.3 V input
O
voltage needs to drop to 3.2 V for purpose of this test).
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Output current
vs Junction temperature
vs Junction temperature
vs Frequency
2, 3
4, 5
6
V
Output voltage
O
Ground current
Power supply rejection ratio
Output spectral noise density
Output impedance
7
vs Frequency
8
Z
o
vs Frequency
9
vs Input voltage
10
V
DO
Dropout voltage
vs Junction temperature
11
Line transient response
12, 14
13, 15
16
Load transient response
Output voltage and enable pulse
Equivalent series resistance (ESR)
vs Time
vs Output current
18 – 21
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
3.302
1.802
1.801
3.301
3.3
1.800
1.799
1.798
3.299
3.298
0
50
100
150
0
50
100
150
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 2
Figure 3
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
JUNCTION TEMPERATURE
1.86
1.84
1.82
3.35
3.33
V = 2.8 V
V = 4.3 V
I
I
I
= 150 mA
O
3.31
3.29
I
O
= 150 mA
1.80
1.78
1.76
3.27
3.25
–40
0
T
40
80
120
160
–40
0
T
40
80
120
160
– Junction Temperature – °C
J
– Junction Temperature – °C
J
Figure 4
Figure 5
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77xxx
GROUND CURRENT
vs
JUNCTION TEMPERATURE
115
110
I
O
= 150 mA
105
100
95
I
O
= 1 mA
90
85
80
–40
10
60
110
160
T
J
– Junction Temperature – °C
Figure 6
TPS77x33
TPS77x33
POWER SUPPLY REJECTION RATIO
OUTPUT SPECTRAL NOISE DENSITY
vs
vs
FREQUENCY
FREQUENCY
10
100
90
80
70
60
50
40
30
20
10
0
C
T
= 10 µF
= 25°C
O
J
C
= 10 µF
= 25°C
O
I
= 1 mA
O
T
J
I
O
= 150 mA
1
I
= 1 mA
O
0.1
0.01
I
= 150 mA
O
100
1k
10k
100k
10
100
1k
10k
100k
1M
10M
f – Frequency – Hz
f – Frequency – Hz
Figure 7
Figure 8
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x33
OUTPUT IMPEDANCE
vs
FREQUENCY
10
I
O
= 1 mA
1
0.1
I
O
= 150 mA
0.01
10
100
1k
10k
100k
1M
10M
f – Frequency – Hz
Figure 9
TPS77x33
TPS77x01
DROPOUT VOLTAGE
vs
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
INPUT VOLTAGE
300
250
200
150
100
I
= 150 mA
O
250
200
150
100
50
T
J
= 125 °C
T
J
= 25 °C
I
O
= 150 mA
T
J
= –40 °C
I
O
= 10 mA
I
O
= 0 A
50
0
0
–50
2.7
3.2
3.7
4.2
4.7
–40
0
40
80
120
160
V – Input Voltage – V
I
T
J
– Junction Temperature – °C
Figure 10
Figure 11
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x18
TPS77x18
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
3.8
2.8
150
0
10
0
0
–50
–10
I
C
T
= 150 mA
O
I
C
T
= 150 mA
O
= 10 µF
–100
O
= 10 µF
O
= 25°C
J
= 25°C
J
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
t – Time – ms
t – Time – ms
Figure 12
Figure 13
TPS77x33
TPS77x33
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
5.3
4.3
150
0
+10
0
0
–50
–10
I
C
T
= 150 mA
I
C
T
= 150 mA
O
O
= 10 µF
= 10 µF
–100
O
O
= 25°C
= 25°C
J
J
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
t – Time – ms
t – Time – ms
Figure 14
Figure 15
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77x33
OUTPUT VOLTAGE AND
ENABLE PULSE
vs
TIME (AT STARTUP)
C
= 10 µF
= 25°C
O
EN
0
T
J
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
t – Time – ms
Figure 16
To Load
IN
V
I
OUT
+
R
L
C
O
EN
GND
ESR
Figure 17. Test Circuit for Typical Regions of Stability (Figures 18 through 21) (Fixed Output Options)
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
TYPICAL REGION OF STABILITY
†
†
EQUIVALENT SERIES RESISTANCE
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
C
= 3.3 V
= 1 µF
O
O
V = 4.3 V
I
J
1
T
= 25°C
Region of Stability
1
Region of Stability
0.1
V
C
= 3.3 V
= 10 µF
O
O
V = 4.3 V
I
J
T
= 25°C
Region of Instability
100
Region of Instability
100 150
0.1
0.01
0
50
150
0
50
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 18
Figure 19
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
TYPICAL REGION OF STABILITY
†
†
EQUIVALENT SERIES RESISTANCE
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
C
= 3.3 V
= 1 µF
O
O
V = 4.3 V
I
J
1
T
= 125 °C
Region of Stability
1
Region of Stability
0.1
V
C
= 3.3 V
= 10 µF
O
O
V = 4.3 V
I
J
T
= 125°C
Region of Instability
100
Region of Instability
100 150
0.1
0.01
0
50
150
0
50
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 20
Figure 21
†
Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to C
.
O
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
pin functions
enable (EN)
The EN terminal is an input which enables or shuts down the device. If EN is a logic high, the device will be in
shutdown mode. When EN goes to logic low, then the device will be enabled.
power good (PG) (TPS772xx)
The PG terminal is an open drain, active high output that indicates the status of V (output of the LDO). When
out
V
reaches 82% of the regulated voltage, PG will go to a high-impedance state. It will go to a low-impedance
out
state when V falls below 82% (i.e. over load condition) of the regulated voltage. The open drain output of the
out
PG terminal requires a pullup resistor
.
sense (SENSE)
The SENSE terminal of the fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier
through a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route
the SENSE connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE
terminal and V to filter noise is not recommended because it may cause the regulator to oscillate.
out
feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and V
recommended because it may cause the regulator to oscillate.
to filter noise is not
out
reset (RESET) (TPS771xx)
TheRESETterminalisanopendrain, activelowoutputthatindicatesthestatusofV . WhenV reaches95%
out
out
of the regulated voltage, RESET will go to a high-impedance state after a 220-ms delay. RESET will go to a
low-impedance state when V is below 95% of the regulated voltage. The open-drain output of the RESET
out
terminal requires a pullup resistor.
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
external capacitor requirements
An input capacitor is not usually required; however, a bypass capacitor (0.047 µF or larger) improves load
transient response and noise rejection if the TPS771xx or TPS772xx is located more than a few inches from
the power supply. A higher-capacitance capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Most low noise LDOs require an external capacitor to further reduce noise. This will impact the cost and board
space. TheTPS771xxandTPS772xxhaveverylownoisespecificationrequirementswithoutusinganyexternal
components.
Like all low dropout regulators, the TPS771xx or TPS772xx requires an output capacitor connected between
OUT (output of the LDO) and GND (signal ground) to stabilize the internal control loop. The minimum
recommended capacitance value is 1 µF provided the ESR meets the requirement in Figures 19 and 21. In
addition, a low-ESR capacitor can be used if the capacitance is at least 10 µF and the ESR meets the
requirements in Figures 18 and 20. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic
capacitors are all suitable, provided they meet the requirements described previously.
Ceramic capacitors have different types of dielectric material with each exhibiting different temperature and
voltage variation. The most common types are X5R, X7R, Y5U, Z5U, and NPO. The NPO type ceramic type
capacitors are generally the most stable over temperature. However, the X5R and X7R are also relatively stable
over temperature (with the X7R being the more stable of the two) and are therefore acceptable to use. The Y5U
and Z5U types provide high capacitance in a small geometry, but exhibit large variations over temperature;
therefore, the Y5U and Z5U are not generally recommended for use on this LDO. Independent of which type
of capacitor is used, one must make certain that at the worst case condition the capacitance/ESR meets the
requirement specified in Figures 18 – 21.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
Figure 22 shows the output capacitor and its parasitic impedances in a typical LDO output stage.
I
O
LDO
–
R
ESR
V
ESR
+
+
V
I
V
O
R
LOAD
–
C
O
Figure 22. LDO Output Stage With Parasitic Resistances ESR and ESL
In steady state (dc state condition), the load current is supplied by the LDO (solid arrow) and the voltage across
the capacitor is the same as the output voltage (V
= V . This means no current is flowing into the C
Cout
out) out
branch. If I
suddenly increases (transient condition), the following occurs:
out
D
The LDO is not able to supply the sudden current need due to its response time (t in Figure 23). Therefore,
1
capacitor C provides the current for the new load condition (dashed arrow). C now acts like a battery
out
out
with an internal resistance, ESR. Depending on the current demand at the output, a voltage drop will occur
at R . This voltage is shown as V in Figure 22.
ESR
ESR
D
When C is conducting current to the load, initial voltage at the load will be V = V
– V
. Due to
out
out
Cout
ESR
the discharge of C , the output voltage V will drop continuously until the response time t of the LDO
out
out
1
is reached and the LDO will resume supplying the load. From this point, the output voltage starts rising again
until it reaches the regulated voltage. This period is shown as t in Figure 23.
2
The figure also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs where number 1 displays the lowest and number 3 displays the highest ESR.
From above, the following conclusions can be drawn:
D
D
The higher the ESR, the larger the droop at the beginning of load transient.
The smaller the output capacitor, the faster the discharge time and the bigger the voltage droop during the
LDO response period.
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
I
out
V
out
1
2
ESR 1
ESR 2
3
ESR 3
t
t
1
2
Figure 23. Correlation of Different ESRs and Their Influence to the Regulation of V
at a
out
Load Step From Low-to-High Output Current
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
programming the TPS77x01 adjustable LDO regulator
The output voltage of the TPS77x01 adjustable regulator is programmed using an external resistor divider as
shown in Figure 24. The output voltage is calculated using:
R1
R2
ǒ1 )
Ǔ
(1)
V
+ V
O
ref
Where:
V
= 1.1834 V typ (the internal reference voltage)
ref
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided, as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 30.1 kΩ to set the divider current at 50 µA and then calculate R1 using:
V
O
R1 +
ǒ
* 1
Ǔ
R2
(2)
V
ref
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS77x01
OUTPUT
VOLTAGE
R1
R2
UNIT
PG or
V
I
IN
PG or RESET Output
250 kΩ
RESET
OUT
0.1 µF
2.5 V
3.3 V
3.6 V
33.5
53.8
61.5
30.1
30.1
30.1
kΩ
kΩ
kΩ
EN
V
O
R1
C
O
NOTE: To reduce noise and prevent
oscillation, R1 and R2 need to be as
close as possible to the FB/SENSE
terminal.
FB/SENSE
GND
R2
Figure 24. TPS77x01 Adjustable LDO Regulator Programming
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
regulator protection
The TPS771xx or TPS772xx PMOS-pass transistor has a built-in back diode that conducts reverse currents
when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from
the output to the input and is not internally limited. When extended reverse voltage is anticipated, external
limiting may be appropriate.
The TPS771xx or TPS772xx also features internal current limiting and thermal protection. During normal
operation, the TPS771xx or TPS772xx limits output current to approximately 0.9 A. When current limiting
engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is
designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of
the package. If the temperature of the device exceeds 150°C(typ), thermal-protection circuitry shuts it down.
Once the device has cooled below 130°C(typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, P
, and the actual dissipation, P , which must be less than
D(max)
D
or equal to P
.
D(max)
The maximum-power-dissipation limit is determined using the following equation:
T max * T
J
A
P
+
D(max)
R
qJA
Where:
T max is the maximum allowable junction temperature.
J
R
is the thermal resistance junction-to-ambient for the package, i.e., 266.2°C/W for the 8-terminal
θJA
MSOP with no airflow.
T is the ambient temperature.
A
The regulator dissipation is calculated using:
+ ǒVI * V
Ǔ
P
I
D
O
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77101/115/118/127/128/133/150 WITH RESET OUTPUT
TPS77201/215/218/227/228/233/250 WITH POWER GOOD OUTPUT
150-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS225D – FEBRUARY 2000 – REVISED OCTOBER 2000
MECHANICAL DATA
DGK (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,38
M
0,65
8
0,25
0,25
5
0,15 NOM
3,05
2,95
4,98
4,78
Gage Plane
0,25
0°–ā6°
1
4
0,69
0,41
3,05
2,95
Seating Plane
0,10
0,15
0,05
1,07 MAX
4073329/B 04/98
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC MO-187
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2005
PACKAGING INFORMATION
Orderable Device
TPS77101DGK
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
MSOP
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77101DGKG4
TPS77101DGKR
TPS77101DGKRG4
TPS77115DGK
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77115DGKR
TPS77115DGKRG4
TPS77118DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77118DGKG4
TPS77118DGKR
TPS77118DGKRG4
TPS77127DGK
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77127DGKR
TPS77127DGKRG4
TPS77128DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77128DGKG4
TPS77128DGKR
TPS77128DGKRG4
TPS77133DGK
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77133DGKG4
TPS77133DGKR
TPS77133DGKRG4
TPS77150DGK
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77150DGKR
TPS77150DGKRG4
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2005
Orderable Device
TPS77201DGK
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
MSOP
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77201DGKR
TPS77201DGKRG4
TPS77215DGK
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77215DGKR
TPS77215DGKRG4
TPS77218DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77218DGKR
TPS77218DGKRG4
TPS77227DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77227DGKR
TPS77227DGKRG4
TPS77228DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77228DGKG4
TPS77228DGKR
TPS77228DGKRG4
TPS77233DGK
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77233DGKR
TPS77233DGKRG4
TPS77250DGK
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TPS77250DGKR
TPS77250DGKRG4
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
Eco Plan
13-Sep-2005
(2)
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明