TPS77301DGKG4 [TI]
250-mA LDO Regulators with Supervisor 8-VSSOP -40 to 125;型号: | TPS77301DGKG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | 250-mA LDO Regulators with Supervisor 8-VSSOP -40 to 125 光电二极管 输出元件 调节器 |
文件: | 总25页 (文件大小:909K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TPS773xx
DGK Package
(TOP VIEW)
D
D
Open Drain Power-On Reset With 220-ms
Delay (TPS773xx)
Open Drain Power-Good (PG) Status
Output (TPS774xx)
FB/SENSE
RESET
EN
OUT
OUT
IN
1
2
3
4
8
7
6
5
D
250-mA Low-Dropout Voltage Regulator
D
Available in 1.5-V, 1.6-V (TPS77316 Only),
1.8-V, 2.7-V, 2.8-V, 3.3-V, 5.0-V Fixed Output
and Adjustable Versions
GND
IN
TPS774xx
DGK Package
(TOP VIEW)
D
Dropout Voltage Typically 200 mV
at 250 mA (TPS77333, TPS77433)
D
D
D
Ultralow 92-µA Quiescent Current (Typ)
FB/SENSE
PG
1
2
3
4
8
7
6
5
OUT
OUT
IN
8-Pin MSOP (DGK) Package
Low Noise (55 µV
) Without an External
rms
EN
Filter (Bypass) Capacitor (TPS77318,
TPS77418)
GND
IN
D
D
D
D
2% Tolerance Over Specified Conditions
For Fixed-Output Versions
TPS77x33
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
Fast Transient Response
Thermal Shutdown Protection
See the TPS779xx Family of Devices for
Active High Enable
300
250
200
150
100
50
I
O
= 250 mA
description
The TPS773xx and TPS774xx are low-dropout
regulators with integrated power-on reset and
power good (PG) function respectively. These
devicesarecapableofsupplying250mAofoutput
current with a dropout of 200 mV (TPS77333,
TPS77433). Quiescent current is 92 µA at full load
dropping down to 1 µA when device is disabled.
These devices are optimized to be stable with a
wide range of output capacitors including lowESR
ceramic (10 µF) or low capacitance (1 µF)
tantalum capacitors. These devices have ex-
I
O
= 10 mA
I
O
= 0 A
0
–50
tremely low noise output performance (55 µV
)
rms
–40
0
40
80
120
160
without using any added filter capacitors.
TPS773xx and TPS774xx are designed to have
fast transient response for larger load current
changes.
T
J
– Junction Temperature – °C
The TPS773xx or TPS774xx is offered in 1.5-V, 1.6 V (TPS77316 only), 1.8-V, 2.7-V, 2.8-V, 3.3-V, and 5.0-V
fixed-voltage versions and in an adjustable version (programmable over the range of 1.5 V to 5.5 V). Output
voltage tolerance is 2% over line, load, and temperature ranges. The TPS773xx and TPS774xx families are
available in 8-pin MSOP (DGK) packages.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
description (continued)
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 200 mV
at an output current of 250 mA for 3.3-volt option) and is directly proportional to the output current. Additionally,
since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent
of output loading (typically 92 µA over the full range of output current, 0 mA to 250 mA). These two key
specifications yield a significant improvement in operating life for battery-powered systems.
The device is enabled when the EN pin is connected to a low-level input voltage. This LDO family also features
a sleep mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent
current to less than 1 µA at T = 25°C.
J
The TPS773xx features an integrated power-on reset, commonly used as a supply voltage supervisor (SVS),
or reset output voltage. The RESET output of the TPS773xx initiates a reset in DSP, microcomputer or
microprocessor systems at power up and in the event of an undervoltage condition. An internal comparator in
the TPS773xx monitors the output voltage of the regulator to detect an undervoltage condition on the regulated
output voltage. When OUT reaches 95% of its regulated voltage, RESET will go to a high-impedance state after
a 220-ms delay. RESET will go to low-impedance state when OUT is pulled below 95% (i.e. over load condition)
of its regulated voltage.
For the TPS774xx, the power good terminal (PG) is an active high output, which can be used to implement a
power-on reset or a low-battery indicator. An internal comparator in the TPS774xx monitors the output voltage
of the regulator to detect an undervoltage condition on the regulated output voltage. When OUTfalls below 82%
of its regulated voltage, PG will go to a low-impedance state. PG will go to a high-impedance state when OUT
is above 82% of its regulated voltage.
AVAILABLE OPTIONS
OUTPUT VOLTAGE (V)
TYP
PACKAGED DEVICES MSOP (DGK)
T
J
TPS773xx
SYMBOL
TPS774xx
SYMBOL
5.0
3.3
2.8
2.7
1.8
1.6
1.5
TPS77350DGK
TPS77333DGK
TPS77328DGK
TPS77327DGK
TPS77318DGK
TPS77316DGK
TPS77315DGK
AGN
AGM
AGK
AGJ
TPS77450DGK
TPS77433DGK
TPS77428DGK
TPS77427DGK
TPS77418DGK
—
AGW
AGV
AGT
AGS
AGQ
—
–40°C to 125°C
AGH
AWF
AGG
TPS77415DGK
AGP
Adjustable
1.5 V to 5.5 V
TPS77301DGK
AGF
TPS77401DGK
AGO
NOTE: The TPS77301 and TPS77401 are programmable using an external resistor divider (see application information).
The DGK package is available taped and reeled. Add an R suffix to the device type (e.g., TPS77301DGKR).
5
6
7
8
1
V
I
IN
IN
OUT
OUT
V
O
SENSE
3
0.1 µF
2
PG or
RESET
EN
PG or RESET Output
10 µF
+
GND
4
Figure 1. Typical Application Configuration (For Fixed Output Options)
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
functional block diagrams
adjustable version
IN
EN
PG or RESET
OUT
_
+
+
_
220 ms Delay
(for TPS773xx Option)
R1
R2
V
ref
= 1.183 V
FB/SENSE
External to the Device
GND
fixed-voltage version
IN
EN
PG or RESET
_
+
OUT
SENSE
+
220 ms Delay
R1
R2
_
(for TPS773xx Option)
V
ref
= 1.183 V
GND
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
TPS773XX
FB/SENSE
RESET
EN
NO.
1
2
I
O
I
Feedback input voltage for adjustable device (sense input for fixed options)
Reset output
3
Enable input
GND
4
Regulator ground
Input voltage
IN
5, 6
7, 8
I
OUT
O
Regulated output voltage
TPS774XX
FB/SENSE
PG
1
2
I
O
I
Feedback input voltage for adjustable device (sense input for fixed options)
Power good
EN
3
Enable input
GND
4
Regulator ground
Input voltage
IN
5, 6
7, 8
I
OUT
O
Regulated output voltage
TPS773xx RESET timing diagram
V
I
†
V
res
†
V
res
t
‡
‡
V
V
O
V
IT+
IT+
Threshold
Voltage
‡
‡
V
IT–
V
IT–
t
RESET
Output
220 ms
Delay
220 ms
Delay
Output
Undefined
Output
Undefined
t
†
V
istheminimuminputvoltageforavalidRESET. ThesymbolV
isnotcurrentlylistedwithinEIAorJEDECstandardsforsemiconductor
– Trip voltage is typically 5% lower than the output voltage (95%V ) V to V is the hysteresis voltage.
O IT–
res
symbology.
res
‡
V
IT
IT+
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TPS774xx PG timing diagram
V
I
†
V
res
†
V
res
t
‡
‡
V
O
V
IT+
V
IT+
Threshold
Voltage
‡
‡
V
IT–
V
IT–
t
PG
Output
Output
Undefined
Output
Undefined
t
†
V
is the minimum input voltage for a valid PG. The symbol V
is not currently listed within EIA or JEDEC standards for semiconductor
– Trip voltage is typically 18% lower than the output voltage (82%V ) V to V is the hysteresis voltage.
O IT–
res
symbology.
res
‡
V
IT
IT+
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
†
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
‡
Input voltage range , V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 13.5 V
I
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 16.5 V
Maximum RESET voltage (TPS773xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Maximum PG voltage (TPS774xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Output voltage, V (OUT, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
O
Operating virtual junction temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 125°C
J
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
†
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network terminal ground.
DISSIPATION RATING TABLE – FREE-AIR TEMPERATURES
AIR FLOW
(CFM)
θ
θ
T
< 25°C
DERATING FACTOR
T
= 70°C
T = 85°C
A
JA
JC
A
A
PACKAGE
(°C/W) (°C/W) POWER RATING
ABOVE T = 25°C
POWER RATING POWER RATING
A
0
266.2
255.2
242.8
3.84
3.92
4.21
376 mW
392 mW
412 mW
3.76 mW/°C
3.92 mW/°C
4.12 mW/°C
207 mW
216 mW
227 mW
150 mW
157 mW
165 mW
150
250
DGK
recommended operating conditions
MIN
2.7
1.5
0
MAX
UNIT
§
Input voltage, V
10
5.5
V
V
I
Output voltage range, V
O
Output current, I (see Note 1)
250
125
mA
°C
O
Operating virtual junction temperature, T (see Note 1)
–40
J
§
To calculate the minimum input voltage for your maximum output current, use the following equation: V
I(min)
= V
+ V
.
DO(max load)
O(max)
NOTE 1: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
electrical characteristics over recommended operating junction temperature range (T = –40°C to
J
125°C), V = V
+ 1 V, I = 1 mA, EN = 0 V, C = 10 µF (unless otherwise noted)
I
O(typ)
O
O
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1.5 V ≤ V ≤ 5.5 V,
T
J
= 25°C
V
O
Adjustable
voltage
O
V
1.5 V ≤ V ≤ 5.5 V
0.98V
1.02V
O
O
O
T
= 25°C,
2.7 V < V < 10 V
IN
1.5
1.6
J
1.5-V Output
V
V
2.7 V < V < 10 V
IN
1.470
1.530
T
J
= 25°C,
2.7 V < V < 10 V
IN
1.6-V Output
1.8-V Output
2.7-V Output
2.8-V Output
3.3-V Output
5.0-V Output
2.7 V < V < 10 V
IN
1.568
1.764
2.646
2.744
3.234
4.900
1.632
1.836
2.754
2.856
3.366
5.100
125
T
J
= 25°C,
2.8 V < V < 10 V
IN
1.8
2.8 V < V < 10 V
IN
Output voltage (see Notes 2 and 4)
T
J
= 25°C,
3.7 V < V < 10 V
IN
2.7
3.7 V < V < 10 V
IN
V
T
J
= 25°C,
3.8 V < V < 10 V
IN
2.8
3.8 V < V < 10 V
IN
T
J
= 25°C,
4.3 V < V < 10 V
IN
3.3
4.3 V < V < 10 V
IN
T
J
= 25°C,
6.0 V < V < 10 V
IN
5.0
V
6.0 V < V < 10 V
IN
T
J
= 25°C
92
Quiescent current (GND current) (see Notes 2 and 4)
µA
V
V
+ 1 V < V ≤ 10 V,
T = 25°C
J
0.005
%/V
%/V
mV
O
I
Output voltage line regulation (∆V /V )(see Note 3)
O
O
+ 1 V < V ≤ 10 V
0.05
O
I
Load regulation
T
J
= 25°C
1
BW = 300 Hz to 100 kHz, T = 25°C,
TPS77318, TPS77418
J
Output noise voltage
55
µVrms
Output current limit
Peak output current
V
= 0 V
0.9
400
144
1.3
A
O
2 ms pulse width,
50% duty cycle
mA
°C
Thermal shutdown junction temperature
EN = V
EN = V
T
J
= 25°C
1
3
µA
µA
I,
I
Standby current
Adjustable
voltage
FB input current
FB = 1.5 V
1
µA
High level enable input voltage
Low level enable input voltage
Enable input current
2
V
V
0.7
1
–1
µA
dB
Power supply ripple rejection (TPS77318, TPS77418) f = 1 kHz,
T
J
= 25°C
55
NOTES: 2. Minimum input operating voltage is 2.7 V or V
current 1 mA.
+ 1 V, whichever is greater. Maximum input voltage = 10 V, minimum output
O(typ)
3. If V < 1.8 V then V
I(max)
= 10 V, V
= 2.7 V:
O
I(min)
OǒVI(max) * 2.7 VǓ
V
ǒ
Ǔ
Line regulation (mV) + %ńV
1000
100
If V > 2.5 V then V
I(max)
= 10 V, V
= V + 1 V:
O
I(min)
ǒVO
) 1 Ǔ
* ǒVO
Ǔ
V
O
I(max)
ǒ
Ǔ
Line regulation (mV) + %ńV
1000
100
4.
I
O
= 1 mA to 250 mA
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
electrical characteristics over recommended operating junction temperature range (T = –40°C to
J
125°C), V = V
+ 1 V, I = 1 mA, EN = 0 V, C = 10 µF (unless otherwise noted) (continued)
I
O(typ)
O
O
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Minimum input voltage for valid PG
Trip threshold voltage
Hysteresis voltage
I
= 300 µA,
V
≤ 0.8 V
1.1
V
(PG)
(PG)
V
decreasing
79
85
%V
%V
V
O
O
PG
(TPS774xx)
Measured at V
0.5
O
O
Output low voltage
V = 2.7 V,
I = 1 mA
(PG)
0.15
0.4
1
I
Leakage current
V
= 5 V
µA
(PG)
Minimum input voltage for valid RESET
Trip threshold voltage
Hysteresis voltage
I
= 300 µA
1.1
V
(RESET)
V
decreasing
92
98
%V
%V
V
O
O
Measured at V
0.5
Reset
(TPS773xx)
O
O
Output low voltage
V = 2.7 V,
I = 1 mA
(RESET)
0.15
0.4
1
I
Leakage current
V
= 5 V
µA
(RESET)
RESET time-out delay
220
270
ms
I
O
I
O
I
O
I
O
I
O
I
O
= 250 mA,
= 250 mA
= 250 mA,
= 250 mA
= 250 mA,
= 250 mA
T
J
T
J
T
J
= 25°C
= 25°C
= 25°C
2.8-V Output
475
330
190
V
V
Dropout voltage (see Note 5)
DO
200
125
3.3-V Output
5.0-V Output
mV
Dropout voltage (see Note 5)
DO
NOTE 5: IN voltage equals V (typ) – 100 mV; 1.5 V, 1.6 V, 1.8-V, and 2.7-V dropout voltage limited by input voltage range limitations (i.e., 3.3
O
V input voltage needs to drop to 3.2 V for purpose of this test).
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Output current
vs Junction temperature
vs Junction temperature
vs Frequency
2, 3
4, 5
6
V
Output voltage
O
Ground current
Power supply rejection ratio
Output spectral noise density
Output impedance
7
vs Frequency
8
Z
o
vs Frequency
9
vs Input voltage
10
V
DO
Dropout voltage
vs Junction temperature
11
Line transient response
12, 14
13, 15
16
Load transient response
Output voltage and enable pulse
Equivalent series resistance (ESR)
vs Time
vs Output current
18 – 21
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
3.302
1.802
1.801
3.301
3.3
1.800
1.799
1.798
3.299
3.298
0
50
100
150
200
250
0
50
100
150
200
250
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 2
Figure 3
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
JUNCTION TEMPERATURE
1.86
3.35
3.33
V = 2.8 V
I
V = 4.3 V
I
1.84
1.82
1.80
1.78
1.76
I
= 250 mA
O
3.31
3.29
I
O
I
O
I
O
= 1 mA
= 50 mA
= 250 mA
3.27
3.25
–40
0
T
40
80
120
160
–40
0
T
40
80
120
160
– Junction Temperature – °C
J
– Junction Temperature – °C
J
Figure 4
Figure 5
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
TPS77xxx
GROUND CURRENT
vs
JUNCTION TEMPERATURE
115
110
105
100
I
O
= 1 mA
95
90
85
80
I
O
= 250 mA
60
–40
10
110
160
T
J
– Junction Temperature – °C
Figure 6
TPS77x33
TPS77x33
POWER SUPPLY REJECTION RATIO
OUTPUT SPECTRAL NOISE DENSITY
vs
vs
FREQUENCY
FREQUENCY
10
100
90
80
70
60
50
40
30
20
10
0
C
T
= 10 µF
= 25 °C
C
T
= 10 µF
O
J
O
J
I
= 1 mA
= 25 °C
O
I
O
= 250 mA
1
I
O
= 1 mA
0.1
0.01
I
= 250 mA
O
100
1k
10k
100k
10
100
1k
10k
100k
1M
10M
f – Frequency – Hz
f – Frequency – Hz
Figure 7
Figure 8
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
TPS77x33
OUTPUT IMPEDANCE
vs
FREQUENCY
10
T
J
= 25 °C
I
O
= 1 mA
1
0.1
I
O
= 250 mA
0.01
10
100
1k
10k
100k
1M
10M
f – Frequency – Hz
Figure 9
TPS77x01
TPS77x33
DROPOUT VOLTAGE
vs
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
JUNCTION TEMPERATURE
400
350
300
250
200
150
100
300
I
= 250 mA
O
T
J
= 125 °C
250
200
150
100
50
I
O
= 250 mA
T
J
= 25 °C
T
J
= –40 °C
I
O
= 10 mA
I
O
= 0 A
0
50
0
–50
2.7
3.2
3.7
4.2
4.7
–40
0
40
80
120
160
V – Input Voltage – V
I
T
J
– Junction Temperature – °C
Figure 10
Figure 11
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
TPS77x18
TPS77x18
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
250
3.8
2.8
0
+50
10
0
0
–50
–10
C
= 10 µF
= 25 °C
= 250 mA
O
C
= 10 µF
= 25 °C
= 250 mA
O
T
I
J
T
I
J
O
O
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
t – Time – ms
t – Time – ms
Figure 12
Figure 13
TPS77x33
TPS77x33
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
250
0
5.3
4.3
10
0
0
–50
–10
C
T
= 10 µF
= 25 °C
= 250 mA
C
T
= 10 µF
= 25 °C
= 250 mA
O
J
O
J
–100
I
O
I
O
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
t – Time – ms
t – Time – ms
Figure 14
Figure 15
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
TPS77x33
OUTPUT VOLTAGE AND
ENABLE PULSE
vs
TIME (AT STARTUP)
C
T
= 10 µF
= 25 °C
O
J
EN
0
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
t – Time – ms
Figure 16
To Load
IN
V
I
OUT
+
R
L
C
O
EN
GND
ESR
Figure 17. Test Circuit for Typical Regions of Stability (Figures 18 through 21) (Fixed Output Options)
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
†
†
EQUIVALENT SERIES RESISTANCE
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
C
= 3.3 V
= 1 µF
O
O
V = 4.3 V
I
J
1
T
= 25°C
Region of Stability
1
0.1
Region of Stability
V
C
= 3.3 V
= 10 µF
O
O
V = 4.3 V
I
J
T
= 25°C
Region of Instability
150 200
Region of Instability
150 200 250
0.1
0.01
0
50
100
0
50
100
250
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 18
Figure 19
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
†
†
EQUIVALENT SERIES RESISTANCE
EQUIVALENT SERIES RESISTANCE
vs
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
C
= 3.3 V
= 1 µF
O
O
V = 4.3 V
I
J
1
T
= 125 °C
Region of Stability
1
0.1
Region of Stability
V
C
= 3.3 V
= 10 µF
O
O
V = 4.3 V
I
J
T
= 125°C
Region of Instability
150 200 250
Region of Instability
150 200
– Output Current – mA
0.01
0.1
0
50
I
100
250
0
50
I
100
– Output Current – mA
O
O
Figure 20
Figure 21
†
Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to C
.
O
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
APPLICATION INFORMATION
pin functions
enable (EN)
The EN terminal is an input which enables or shuts down the device. If EN is a logic high, the device will be in
shutdown mode. When EN goes to logic low, then the device will be enabled.
power good (PG) (TPS774xx)
The PG terminal is an open drain, active high output that indicates the status of V (output of the LDO). When
out
V
reaches 82% of the regulated voltage, PG will go to a high-impedance state. It will go to a low-impedance
out
state when V falls below 82% (i.e. over load condition) of the regulated voltage. The open drain output of the
out
PG terminal requires a pullup resistor
.
sense (SENSE)
The SENSE terminal of the fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier
through a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route
the SENSE connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE
terminal and V to filter noise is not recommended because it may cause the regulator to oscillate.
out
feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and V
recommended because it may cause the regulator to oscillate.
to filter noise is not
out
reset (RESET) (TPS773xx)
TheRESETterminalisanopendrain, activelowoutputthatindicatesthestatusofV . WhenV reaches95%
out
out
of the regulated voltage, RESET will go to a high-impedance state after a 220-ms delay. RESET will go to a
low-impedance state when V is below 95% of the regulated voltage. The open-drain output of the RESET
out
terminal requires a pullup resistor.
external capacitor requirements
An input capacitor is not usually required; however, a bypass capacitor (0.047 µF or larger) improves load
transient response and noise rejection if the TPS773xx or TPS774xx is located more than a few inches from
the power supply. A higher-capacitance capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Most low noise LDOs require an external capacitor to further reduce noise. This will impact the cost and board
space. TheTPS773xxandTPS774xxhaveverylownoisespecificationrequirementswithoutusinganyexternal
components.
Like all low dropout regulators, the TPS773xx or TPS774xx requires an output capacitor connected between
OUT (output of the LDO) and GND (signal ground) to stabilize the internal control loop. The minimum
recommended capacitance value is 1 µF provided the ESR meets the requirement in Figures 19 and 21. In
addition, a low-ESR capacitor can be used if the capacitance is at least 10 µF and the ESR meets the
requirements in Figures 18 and 20. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic
capacitors are all suitable, provided they meet the requirements described previously.
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
APPLICATION INFORMATION
external capacitor requirements (continued)
Ceramic capacitors have different types of dielectric material with each exhibiting different temperature and
voltage variation. The most common types are X5R, X7R, Y5U, Z5U, and NPO. The NPO type ceramic type
capacitors are generally the most stable over temperature. However, the X5R and X7R are also relatively stable
over temperature (with the X7R being the more stable of the two) and are therefore acceptable to use. The Y5U
and Z5U types provide high capacitance in a small geometry, but exhibit large variations over temperature;
therefore, the Y5U and Z5U are not generally recommended for use on this LDO. Independent of which type
of capacitor is used, one must make certain that at the worst case condition the capacitance/ESR meets the
requirement specified in Figures 18 – 21.
Figure 22 shows the output capacitor and its parasitic impedances in a typical LDO output stage.
I
O
LDO
–
R
ESR
V
ESR
+
+
V
I
V
O
R
LOAD
–
C
O
Figure 22. LDO Output Stage With Parasitic Resistances ESR
In steady state (dc state condition), the load current is supplied by the LDO (solid arrow) and the voltage across
the capacitor is the same as the output voltage (V = V . This means no current is flowing into the C
Cout
out)
out
branch. If I
suddenly increases (transient condition), the following occurs:
out
D
The LDO is not able to supply the sudden current need due to its response time (t in Figure 23). Therefore,
1
capacitor C provides the current for the new load condition (dashed arrow). C now acts like a battery
out
out
with an internal resistance, ESR. Depending on the current demand at the output, a voltage drop will occur
at R . This voltage is shown as V in Figure 22.
ESR
ESR
D
When C is conducting current to the load, initial voltage at the load will be V = V
– V
. Due to
out
out
Cout
ESR
the discharge of C , the output voltage V will drop continuously until the response time t of the LDO
out
out
1
is reached and the LDO will resume supplying the load. From this point, the output voltage starts rising again
until it reaches the regulated voltage. This period is shown as t in Figure 23.
2
The figure also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs where number 1 displays the lowest and number 3 displays the highest ESR.
From above, the following conclusions can be drawn:
D
D
The higher the ESR, the larger the droop at the beginning of load transient.
The smaller the output capacitor, the faster the discharge time and the bigger the voltage droop during the
LDO response period.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
APPLICATION INFORMATION
conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
I
out
V
out
1
2
ESR 1
ESR 2
3
ESR 3
t
t
1
2
Figure 23. Correlation of Different ESRs and Their Influence to the Regulation of V
at a
out
Load Step From Low-to-High Output Current
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
APPLICATION INFORMATION
programming the TPS77x01 adjustable LDO regulator
The output voltage of the TPS77x01 adjustable regulator is programmed using an external resistor divider as
shown in Figure 24. The output voltage is calculated using:
R1
R2
ǒ1 )
Ǔ
(1)
V
+ V
O
ref
Where:
V
= 1.1834 V typ (the internal reference voltage)
ref
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided, as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 30.1 kΩ to set the divider current at 50 µA and then calculate R1 using:
V
O
R1 +
ǒ
* 1
Ǔ
R2
(2)
V
ref
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS77x01
OUTPUT
VOLTAGE
R1
R2
UNIT
PG or
V
I
IN
PG or RESET Output
250 kΩ
RESET
OUT
0.1 µF
2.5 V
3.3 V
3.6 V
33.5
53.8
61.5
30.1
30.1
30.1
kΩ
kΩ
kΩ
EN
V
O
R1
C
O
NOTE: To reduce noise and prevent
oscillation, R1 and R2 need to be as
close as possible to the FB/SENSE
terminal.
FB/SENSE
GND
R2
Figure 24. TPS77x01 Adjustable LDO Regulator Programming
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS77301/315/316/318/327/328/333/350 WITH RESET OUTPUT
TPS77401/415/418/427/428/433/450 WITH POWER GOOD OUTPUT
250-mA LDO REGULATORS WITH 8-PIN MSOP PACKAGING
SLVS281E – FEBRUARY 2000 – REVISED JULY 2001
APPLICATION INFORMATION
regulator protection
The TPS773xx or TPS774xx PMOS-pass transistor has a built-in back diode that conducts reverse currents
when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from
the output to the input and is not internally limited. When extended reverse voltage is anticipated, external
limiting may be appropriate.
The TPS773xx or TPS774xx also features internal current limiting and thermal protection. During normal
operation, the TPS773xx or TPS774xx limits output current to approximately 0.9 A. When current limiting
engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is
designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of
the package. If the temperature of the device exceeds 150°C(typ), thermal-protection circuitry shuts it down.
Once the device has cooled below 130°C(typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, P
, and the actual dissipation, P , which must be less than
D(max)
D
or equal to P
.
D(max)
The maximum-power-dissipation limit is determined using the following equation:
T max * T
J
A
P
+
D(max)
R
qJA
Where:
T max is the maximum allowable junction temperature.
J
R
is the thermal resistance junction-to-ambient for the package, i.e., 266.2°C/W for the 8-terminal
θJA
MSOP with no airflow.
T is the ambient temperature.
A
The regulator dissipation is calculated using:
+ ǒVI * V
Ǔ
P
I
D
O
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
23-Aug-2017
PACKAGING INFORMATION
Orderable Device
TPS77301DGK
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
AGF
AGF
AGF
AGF
AGG
AGG
AWF
AWF
AWF
AGH
AGH
AGH
AGH
AGK
AGK
AGM
AGM
TPS77301DGKG4
TPS77301DGKR
TPS77301DGKRG4
TPS77315DGK
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
80
2500
2500
80
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS77315DGKR
TPS77316DGK
2500
80
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS77316DGKR
TPS77316DGKRG4
TPS77318DGK
2500
2500
80
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS77318DGKG4
TPS77318DGKR
TPS77318DGKRG4
TPS77328DGK
80
Green (RoHS
& no Sb/Br)
2500
2500
80
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS77328DGKG4
TPS77333DGK
80
Green (RoHS
& no Sb/Br)
80
Green (RoHS
& no Sb/Br)
TPS77333DGKG4
80
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Aug-2017
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
TPS77333DGKR
TPS77333DGKRG4
TPS77350DGK
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
AGM
AGM
AGN
AGN
AGN
AGO
AGO
AGP
AGQ
AGQ
AGT
AGV
AGV
AGV
AGV
AGW
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
DGK
2500
80
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS77350DGKG4
TPS77350DGKR
TPS77401DGK
80
Green (RoHS
& no Sb/Br)
2500
80
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS77401DGKG4
TPS77415DGK
80
Green (RoHS
& no Sb/Br)
80
Green (RoHS
& no Sb/Br)
TPS77418DGK
80
Green (RoHS
& no Sb/Br)
TPS77418DGKG4
TPS77428DGK
80
Green (RoHS
& no Sb/Br)
80
Green (RoHS
& no Sb/Br)
TPS77433DGK
80
Green (RoHS
& no Sb/Br)
TPS77433DGKG4
TPS77433DGKR
TPS77433DGKRG4
TPS77450DGK
80
Green (RoHS
& no Sb/Br)
2500
2500
80
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
23-Aug-2017
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Aug-2017
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS77301DGKR
TPS77315DGKR
TPS77316DGKR
TPS77318DGKR
TPS77333DGKR
TPS77350DGKR
TPS77433DGKR
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
DGK
DGK
DGK
DGK
DGK
DGK
DGK
8
8
8
8
8
8
8
2500
2500
2500
2500
2500
2500
2500
330.0
330.0
330.0
330.0
330.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
12.4
5.3
5.3
5.3
5.3
5.3
5.3
5.3
3.4
3.4
3.4
3.4
3.4
3.4
3.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Aug-2017
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS77301DGKR
TPS77315DGKR
TPS77316DGKR
TPS77318DGKR
TPS77333DGKR
TPS77350DGKR
TPS77433DGKR
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
VSSOP
DGK
DGK
DGK
DGK
DGK
DGK
DGK
8
8
8
8
8
8
8
2500
2500
2500
2500
2500
2500
2500
358.0
358.0
358.0
358.0
358.0
358.0
358.0
335.0
335.0
335.0
335.0
335.0
335.0
335.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明