UC1517J883B [TI]

STEPPER MOTOR CONTROLLER, 0.5A, CDIP16, DIP-16;


型号：	UC1517J883B
厂家：	TEXAS INSTRUMENTS
描述：	STEPPER MOTOR CONTROLLER, 0.5A, CDIP16, DIP-16 电动机控制 CD
文件：	总12页 (文件大小：535K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

UC1517

UC3517

Stepper Motor Drive Circuit

FEATURES

DESCRIPTION

•

Complete Motor Driver and Encoder

The UC3517 contains four NPN drivers that operate in two-phase

fashion for full-step and half-step motor control. The UC3517

also contains two emitter followers, two monostables, phase de-

coder logic, power-on reset, and low-voltage protection, making it

a versatile system for driving small stepper motors or for control-

ling large power devices.

Continuous Drive Capability 350mA per Phase

Contains all Required Logic for Full and Half

Stepping

•

Bilevel Operation for Fast Step Rates

Operates as a Voltage Doubler

The emitter followers and monostables in the UC3517 are config-

ured to apply higher-voltage pulses to the motor at each step

command. This drive technique, called “Bilevel,” allows faster

stepping than common resistive current limiting, yet generates

less electrical noise than chopping techniques.

Useable as a Phase Generator and/or as a

Driver

•

Power-On Reset Guarantees Safe,

Predictable Power-Up

ABSOLUTE MAXIMUM RATINGS

Second Level Supply, VSS . . . . . . . . . . . . . . . . . . . . . . . . . . 40V Power Dissipation, (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2W

Phase Output Supply, VMM . . . . . . . . . . . . . . . . . . . . . . . . . 40V Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C

Logic Supply, VCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Ambient Temperature, UC1517. . . . . . . . . . . . -55°C to +125°C

Logic Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . -.3V to +7V Ambient Temperature, UC3517 . . . . . . . . . . . . . . 0°C to +70°C

Logic Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA Storage Temperature . . . . . . . . . . . . . . . . . . . -55°C to +150°C

Output Current, Each Phase . . . . . . . . . . . . . . . . . . . . . . 500mA Note: Consult Packaging section of Databook for thermal

limitations and considerations of package.

Output Current, Emitter Follower . . . . . . . . . . . . . . . . . . -500mA

Power Dissipation, (Note). . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W

BLOCK DIAGRAM

8/94

UC1517

UC3517

CONNECTION DIAGRAMS

PACKAGE PIN FUNCTION

PLCC-20, LCC-20

(TOP VIEW)

Q & L PACKAGE

DIL-16 (TOP VIEW)

J or N Package

FUNCTION

N/C

PB2

PB1

GND

PA1

N/C

PA2

DIR

STEP

ØB

N/C

ØA

HSM

INH

N/C

VSS

VCC

Unless otherwise stated, these specifications apply for TA = -55°C to +125°C for the

ELECTRICAL CHARACTERISTICS:

UC1517 and 0°C to +70°C for the UC3517, Vcc=5V, VSS = 20V, TA=TJ Pin

numbers refer to DIL-16 package.

UC1517 / UC3517

UNITS

PARAMETER

TEST CONDITIONS

MIN

4.75

TYP

MAX

5.25

Logic Supply, VCC

Second Supply, VSS

Logic Supply Current

Pin 16

Pin 15

VINH = 0.4V

VINH = 4.0V

Input Low Voltage

Pins 6, 7, 10, 11

Pins 6, 7, 10, 11; V = 0V

Pins 6, 7, 10, 11; V = 5V

Pins 1, 2, 4, 5; I = 350mA

Pins 1, 2, 4, 5; V = 39V

Pins 13,14; I = 350mA

Pins 13,14; V = 0V

Pins 8, 9; I = 1.6mA

Pins 1, 2, 4, 5

0.8

Input High Voltage

2.0

Input Low Current

-400

µA

Input High Current

0.85

500

-2

Phase Output Saturation Voltage

Phase Output Leakage Current

Follower Saturation Voltage to VSS

Follower Leakage Current

Output Low Voltage, ØA, ØB

Phase Turn-On Time

0.6

µA

500

0.4

µA

0.1

µs

Ω

Phase Turn-Off Time

Pins 1, 2, 4, 5

1.8

325

Second-Level On Time. TMONO

Logic Input Set-up Time, tS

Logic Input Hold Time, th

STEP Pulse Width, tP

Pins 13,14; Figure 3 Test Circuit

Pins 6, 10; Figure 4

Pin 7; Figure 4

Pin 12

275

400

375

800

Timing Resistor Value

Timing Capacitor Value

Power-On Threshold

100k

500

Pin 12

0.1

Pin 16

4.3

3.8

0.5

Power-Off Threshold

Pin 16

Power Hysteresis

Pin 16

UC1517

UC3517

Figure 3. Test Circuit

Figure 4. Timing Waveforms

PIN DESCRIPTION

VCC: VCC is the UC3517’s logic supply. Connect to a as shown in Figure 8. The sequencing of these outputs is

shown in Figure 5.

regulated 5VDC, and bypass with a 0.1µF ceramic ca-

pacitor to absorb switching transients.

PA1, PA2, PB1, and PB2: The phase outputs pull to

ground sequentially to cause motor stepping, according to

the state diagram of Figure 5. The sequence of stepping

on these lines, as well as with the LA and LB lines is con-

trolled by STEP input, the DIR input, and the HSM input.

Caution: If these outputs or any other IC pins are pulled

too far below ground either continuously or in a transient,

step memory can be lost. It is recommended that these

pins be clamped to ground and supply with high-speed di-

odes when driving inductive loads such as motor wind-

ings or solenoids. This clamping is very important

because one side of the winding can "kick" in a direction

opposite the swing of the other side.

VMM: VMM is the primary motor supply. It connects to the

UC3517 phase outputs through the motor windings. Limit

this supply to less than 40V to prevent breakdown of the

phase output transistors. Select the nominal VMM voltage

for the desired continuous winding current.

VSS: VSS is the secondary motor supply. It drives the LA

and LB outputs of the UC3517 when a monostable in the

UC3517 is active. In the bilevel application, this supply is

applied to the motor to charge the winding inductance

faster than the primary supply could. Typically, Vss is

higher in voltage than VMM, although VSS must be less

than 40V. The VSS supply should have good transient ca-

pability.

LA and LB: These outputs pull to VSS when their corre-

sponding monostable is active, and will remain high until

the monostable time elapses. Before and after, these out-

puts are high-impedance. For detail timing information,

consult Figure 5.

GROUND: The ground pin is the common reference for

all supplies, inputs and outputs.

RC: RC controls the timing functions of the monostables

in the UC3517. It is normally connected to a resistor (RT)

and a capacitor (CT) to ground, as shown in Figure 3.

Monostable on time is determined by the formula TON ≈

0.69 RT CT. To keep the monostable on indefinitely, pull

RC to VCC through a 50k resistor. The UC3517 contains

only one RC pin for two monostables. If step rates com-

parable to TON are commanded, incorrect pulsing can re-

sult, so consider maximum step rates when selecting RT

and CT. Keep TON ≤ T STEP MAX.

STEP: This logic input clocks the logic in the UC3517 on

every falling edge. Like all other UC3517 inputs, this input

is TTL/CMOS compatible, and should not be pulled below

ground.

DIR: This logic input controls the motor rotation direction

by controlling the phase output sequence as shown in

Figure 5. This signal must be stable 400ns before a falling

edge on STEP, and must remain stable through the edge

to insure correct stepping.

ØA and ØB: These logic outputs indicate half-step posi-

tion. These outputs are open-collector, low-current driv-

ers, and may directly drive TTL logic. They can also drive

CMOS logic if a pull-up resistor is provided. Systems

which use the UC3517 as an encoder and use a different

driver can use these outputs to disable the external driver,

HSM: This logic input switches the UC3517 between half-

stepping (HSM = low) and full-stepping (HSM = high) by

controlling the phase output sequence as show in Figure

5. This line requires the same set-up time as the DIR in-

put, and has the same hold requirement.

UC1517

UC3517

used in conjunction with discrete power transistors or

power driver ICs, like the L298. These can be connected

as current gain devices that turn on when the phase out-

puts turn on.

INH: When the inhibit input is high, the phase and θ out-

puts are inhibited (high impedance). STEP pulses re-

ceived while inhibited will continue to update logic in the

IC, but the states will not be reflected at the outputs until

inhibit is pulled low. In stepper motor systems, this can be

used to save power or to allow the rotor to move freely for

manual repositioning.

Bipolar Motor Drive: Bipolar motors can be controlled by

the UC3517 with the addition of bipolar integrated drivers

such as the UC3717A (Figure 8) and the L298, or discrete

devices. Care should be taken with discrete devices to

avoid potential cross-conduction problems.

OPERATING MODES

The UC3517 is a system component capable of many dif-

ferent operating modes, including:

LOGIC FLOW GRAPH

The UC3517 contains a bidirectional counter which is de-

coded to generate the correct phase and Ø outputs. This

counter is incremented on every falling edge of the STEP

input. Figure 5 shows a graph representing the counter

sequence, inputs that determine the next state (DIR and

HSM), and the outputs at each state. Each circle repre-

sents a unique logic state, and the four inside circles rep-

resent the half-step states.

Unipolar Stepper Driver: In its simplest form, the

UC3517 can be connected to a stepper motor as a unipo-

lar driver. LA, LB, RC and Vss are not used, and may be

left open. All other system design considerations men-

tioned above apply, including choice of motor supply

VMM, undershoot diodes and timing considerations.

Unipolar Bilevel Stepper Driver: If increased step rates

are desired, the application circuit of Figure 6 makes use

of the monostables and emitter followers as well as the

configuration mentioned above to provide high-voltage

pulses to the motor windings when the phase is turned

on. For a given dissipation level, this mode offers faster

step rates, and very little additional electrical noise.

The four bits inside the circles represent the phase out-

puts in each state (PA1, PA2, PB1, and PB2). For example,

the circle labeled 1010 is immediately entered when the

device is powered up, and represents PA1 off ("1" or

high), PA2 on ("0" or low), PB1 off ("1" or high) and PB2 on

("0" or low). The ØA and ØB outputs are both low (uniden-

tified).

The choice of monostable components can be estimated

based on the timing relationship of motor current and volt-

age: V = Ldl/dt. Assuming a fixed secondary supply volt-

age (VSS), a fixed winding inductance (LM), a desired

winding peak current (IW), and no back EMF from the mo-

tor, we can estimate that RTCT = 1.449 IWLM/VSS. In

practice, these calculations should be confirmed and ad-

justed to accommodate for effects not modeled.

The arrows in the graph show the state changes. For ex-

ample, if the IC is in state 0110, DIR is high, HSM is high,

and STEP falls, the next state will be 0101, and a pulse

will be generated on the LB line by the monostable.

Inhibit will not effect the logic state, but it will cause all

phase outputs and both Ø outputs to go high (off). A fall-

ing edge on STEP will still cause a state change, but in-

hibit will have to toggle low for the state to be apparent.

Voltage-Doubled Mode: The UC3517 can also be used

to generate higher voltages than available with the sys-

tem power supplies using capacitors and diodes. Figure 9

shows how this might be done, and gives some estimates

for the component values.

A falling edge on STEP with HSM high will cause the

counter to advance to the next full step state regardless

of whether or not it was in a full step state previously.

Higher Current Operation: For systems requiring more

than 350mA of drive per phase, the UC3717A can be

No LA or LB pulses are generated entering half-states.

UC1517

UC3517

Figure 5. Logic Flow Graph

For applications requiring very fast step rates, a zener diode not overshoot past 40V. If the zener diodes are not used and

permits windings to discharge at higher voltages, and higher UC3610 pin 2 is connected directly to Vss then higher Vss can

rates. Driver transistor breakdown must be considered when be used.

selecting Vss and zener voltage to insure that the outputs will

Figure 6. Bilevel Motor Driver

UC1517

UC3517

Experimental selection of RT and CT allow the designer to se- tion can be well controlled. Average power dissipation for the

lect a small amount of winding current overshoot, as shown driver and motor must be considered when designing sys-

above. Although the overshoot may exceed the continuous tems with intentional overshoot, and must stay within conser-

rated current of the winding and the drive transistors, the dura- vative limits for short duty cycles.

Figure 7. Effects of Different RT & CT on Bilevel Systems

In this application, the A and B outputs of the UC3517 are also allows half-step operation of the UC3717. Peak motor

connected to the current program inputs of the UC3717. This winding current will be limited to approximately .42V/R1 by

allows the UC3517 inhibit signal to inhibit the UC3717, and chopping.

Figure 8. Interface to UC3717 Bipolar Driver

UC1517

UC3517

Although component values can be best optimized experimentally, good starting values speed development. For this design,

start with: where:

RT CT = 3 LW/RW LW is winding inductance,

C1 = C2 = LW IR/RW

R1 = R2 = 2.9 TMIN/C1

RW is winding resistance,

IR is rated winding current, and

TMIN is minimum step period expected.

Figure 9. Using the UC3517 as a Voltage Doubler

UNITRODE INTEGRATED CIRCUITS

7 CONTINENTAL BLVD. • MERRIMACK, NH 03054

TEL. (603) 424-2410 • FAX (603) 424-3460

PACKAGE OPTION ADDENDUM

www.ti.com

9-May-2012

PACKAGING INFORMATION

Status ⁽¹⁾

Eco Plan ⁽²⁾

MSL Peak Temp ⁽³⁾

Samples

Orderable Device

Package Type Package

Drawing

Pins

Package Qty

Lead/

Ball Finish

(Requires Login)

Add to cart

UC1517J

UC1517J883B

UC1517L

OBSOLETE

UTR

TBD

Call TI

UC3517N

PDIP

PLCC

UC3517Q

UC3517QTR

⁽¹⁾The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

⁽²⁾Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

⁽³⁾MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF UC1517, UC3517 :

Addendum-Page 1

PACKAGE OPTION ADDENDUM

www.ti.com

9-May-2012

Catalog: UC3517

•

Military: UC1517

•

NOTE: Qualified Version Definitions:

Catalog - TI's standard catalog product

•

Military - QML certified for Military and Defense Applications

Addendum-Page 2

MECHANICAL DATA

MPLC004A – OCTOBER 1994

FN (S-PQCC-J**)

PLASTIC J-LEADED CHIP CARRIER

20 PIN SHOWN

Seating Plane

0.004 (0,10)

0.180 (4,57) MAX

0.120 (3,05)

0.090 (2,29)

0.020 (0,51) MIN

0.032 (0,81)

0.026 (0,66)

D2/E2

0.021 (0,53)

0.013 (0,33)

0.050 (1,27)

0.007 (0,18)

0.008 (0,20) NOM

D/E

D1/E1

D2/E2

NO. OF

PINS

MIN

0.385 (9,78)

MAX

MIN

MAX

MIN

MAX

0.395 (10,03)

0.350 (8,89)

0.356 (9,04)

0.141 (3,58)

0.191 (4,85)

0.291 (7,39)

0.341 (8,66)

0.169 (4,29)

0.219 (5,56)

0.319 (8,10)

0.369 (9,37)

0.485 (12,32) 0.495 (12,57) 0.450 (11,43) 0.456 (11,58)

0.685 (17,40) 0.695 (17,65) 0.650 (16,51) 0.656 (16,66)

0.785 (19,94) 0.795 (20,19) 0.750 (19,05) 0.756 (19,20)

0.985 (25,02) 0.995 (25,27) 0.950 (24,13) 0.958 (24,33) 0.441 (11,20) 0.469 (11,91)

1.185 (30,10) 1.195 (30,35) 1.150 (29,21) 1.158 (29,41) 0.541 (13,74) 0.569 (14,45)

4040005/B 03/95

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.

C. Falls within JEDEC MS-018

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products

Audio

Applications

www.ti.com/audio

amplifier.ti.com

dataconverter.ti.com

www.dlp.com

Automotive and Transportation www.ti.com/automotive

Communications and Telecom www.ti.com/communications

Amplifiers

Data Converters

DLP® Products

DSP

Computers and Peripherals

Consumer Electronics

Energy and Lighting

Industrial

www.ti.com/computers

www.ti.com/consumer-apps

www.ti.com/energy

dsp.ti.com

Clocks and Timers

Interface

www.ti.com/clocks

interface.ti.com

logic.ti.com

www.ti.com/industrial

www.ti.com/medical

www.ti.com/security

Medical

Logic

Security

Power Mgmt

Microcontrollers

RFID

power.ti.com

Space, Avionics and Defense www.ti.com/space-avionics-defense

microcontroller.ti.com

www.ti-rfid.com

Video and Imaging

www.ti.com/video

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page

e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

UC1517J883B [TI]

相关型号：

UC1517L

UC1524

UC1524A

UC1524AJ

UC1524AJ/80503

UC1524AJ/883BC

UC1524AJ883B

UC1524AL

UC1524AL883B

UC1524A_08

UC1524A_16

UC1524J