XC6211A36ADL_技术文档

◆CMOS Low Power Consumption

■APPLICATIONS

◆Dropout Voltage

: 60mV@30mA

●Mobile phones

200mV@100mA

: 150mA (VOUT<1.75V)

240mA (VOUT≧1.8V)

(300mA limit)

●

Cordless phones, radio communication equipment

◆Output Current

●Portable games

●Cameras, Video cameras

●Reference voltage sources

●Battery powered equipment

◆Highly Accurate

: ±2%(VOUT>1.5V)

±30mV (VOUT≦1.5V)

◆Output Voltage Range : 0.9V to 5.0V (50mV increments)

◆Low ESR Capacitor Compatible

■GENERAL DESCRIPTION

■FEATURES

The XC6211/XC6219 series are highly accurate, low noise,

CMOS LDO Voltage Regulators. Offering low output noise, high

ripple rejection ratio, low dropout and very fast turn-on times,

the XC6211/6219 series is ideal for today’s cutting edge mobile

phone.

Maximum Output Current : 150mA (VOUT<1.75V)

240mA (VOUT≧1.8V)

(300mA limit (TYP.))

: 200mV (IOUT=100mA)

Dropout Voltage

Internally the XC6211/6219 includes a reference voltage

source, error amplifiers, driver transistors, current limiters and

phase compensators. The XC6211/6219’s current limiters'

foldback circuit also operates as a short protect for the output

current limiter and. the output pin. The output voltage is set by

laser trimming.

Voltages are selectable in 50mV steps within a range of 0.9V to

5.0V. The XC6211/6219 series is also fully compatible with

low ESR ceramic capacitors, reducing cost and improving

output stability.

Operating Voltage Range : 2.0V ~ 6.0V

Output Voltage Range

Highly Accuracy

: 0.9V ~ 5.0V (50mV steps)

: ±2% (VOUT>1.5)

±30mV (VOUT≦1.5V)

Low Power Consumption : 25μA (TYP.)

Standby Current

: Less than 0.1μA (TYP.)

High Ripple Rejection

: 65dB @10kHz

Operating Temperature Range : -40℃ ~ 85℃

This high level of output stability is maintained even during

frequent load fluctuations, due to the excellent transient

response performance and high PSRR achieved across a

broad range of frequencies.

Low ESR Capacitor

Ultra Small Packages

: Ceramic capacitor

: SOT-25 (SOT-23-5)

SOT-89-5(XC6219)

USP-6B(XC6219)

The CE function allows the output of regulator to be turned off,

resulting in greatly reduced power consumption.

■TYPICAL APPLICATION CIRCUIT

●XC6219 series

■TYPICAL PERFORMANCE

CHARACTERISTICS

●Ripple Rejection Rate

XC6211x302

VIN=3.0V, DC + Vp-pAC,

IOUT=50mA, CL=1μF (ceramics)

VOUT

NC

VIN

VSS

CE

1

2

5

4

100

90

80

70

60

50

40

30

20

10

0

CL

µ

1 F

3

CIN

µ

1 F

SOT-25 (SOT-23-5)

0.01

0.1

1

10

100

Ripple Frequency f (kHz)

277

XC6211/6219 Series

■PIN CONFIGURATION

[XC6211 Series]

VIN

5

VOUT

4

2

3

1

CE VSS

NC

SOT-25 (SOT-23-5)

(TOP VIEW)

[XC6219 Series]

VOUT

5

NC

4

VIN

4

VOUT VSS

5

2

VIN

CE

VSS

NC

2

3

CE

1

NC

2

VSS

VOUT

VIN

VSS CE

SOT-25 (SOT-23-5)

(TOP VIEW)

SOT-89-5

(TOP VIEW)

*Please use the circuit without connecting the heat dissipation

pad. If the pad needs to be connected to other pins, it should

be noted that the pin configuration of the USP-6B package is

different on the IC series. Please refer to Contents-2.

■PIN ASSIGNMENT

PIN NUMBER

PIN NAME

FUNCTIONS

XC6211

XC6219

SOT-25 SOT-25 SOT-89-5 USP-6B

5

2

1

3

4

1

2

3

4

5

4

2

3

1

5

1

5

VIN

VSS

CE

Power Input

Ground

ON / OFF Control

No Connection

Output

6

2, 4

3

NC

VOUT

278

XC6211/6219

Series

■PRODUCT CLASSIFICATION

●Selection Guide

The following options for the CE pin logic and internal pull-up/down are available:

High Active + no pull-down resistor built-in (standard)

High Active + 2.0MΩ pull-down resistor built-in <between CE-VSS> (semi-custom)

Low Active + no pull-up resistor built-in (semi-custom)

Low Active + 2.0MΩ pull-up resistor built-in <between VIN-CE> (semi-custom)

Note: *With the pull-up resistor or pull-down resistor built-in types, the supply current during operation will increase

by VIN / 2.0MΩ (TYP.)

●Ordering Information

XC6211/XC6219 ①②③④⑤⑥

DESIGNATOR

DESCRIPTION

SYMBOL

DESCRIPTION

A

B

C

D

: High Active (pull-down resistor built in)

: High Active (no pull-down resistor built in)

: Low Active (pull-up resistor built in)

: Low Active (no pull-up resistor built in)

CE Pin Logic

Output Voltage

①

09～50

② ③

④

: e.g. ②=3, ③=0, → 3.0V

: 100mV increments, ±2% accuracy

e.g. ③=2, ③=8, ④=2 → 2.80V, ±2%

: 50mV increments, ±2% accuracy

e.g. ②=2, ③=8, ④=A → 2.85V, ±2%

: SOT-25 (SOT-23-5)

: SOT-89-5 (XC6219)

: USP-6B (XC6219)

2

A

M

P

D

Packages

⑤

⑥

R

: Embossed tape, Standard feed

: Embossed tape, Reverse feed

Device Orientation

L

279

XC6211/6219 Series

■PACKAGING INFORMATION

●SOT-25 (SOT-23-5)

●SOT-89-5

●USP-6B

2.0±0.15

(0.45) 0.5±0.1

(0.05)

A

A’

1

2

3

6

5

4

(0.45) (0.45)

0.7±0.03

A-A' cross section

3

2

1

4

5

6

1.0±0.1

0.25±0.1

Note : Pin 1 is larger than the other pins.

280

XC6211/6219

Series

■MARKING RULE

[XC6211 Series]

●SOT-25(SOT-23-5)

5

4

①Represents product series

MARK

A

PRODUCT SERIES

XC6211xxxxMx

①

②

③

④

②Represents type of regulator

1

2

3

MARK

PRODUCT SERIES

VOUT 100mV STEPS

VOUT 50mV STEPS

VOUT:0.1~3.0V VOUT:3.1~6.0V VOUT:0.15~3.05V VOUT:3.15~6.05V

V

X

Y

Z

A

B

C

D

E

F

H

K

L

M

N

P

XC6211AxxxMx

XC6211BxxxMx

XC6211CxxxMx

XC6211DxxxMx

③Represents output voltage

OUTPUT VOLTAGE

MARK

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

4.6 1.65 4.65

4.7 1.75 4.75

4.8 1.85 4.85

4.9 1.95 4.95

5.0 2.05 5.05

5.1 2.15 5.15

5.2 2.25 5.25

5.3 2.35 5.35

5.4 2.45 5.45

5.5 2.55 5.55

5.6 2.65 5.65

5.7 2.75 5.75

5.8 2.85 5.85

5.9 2.95 5.95

6.0 3.05 6.05

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

-

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.1

4.2

4.3

4.4

4.5

-

3.15

3.25

3.35

3.45

3.55

3.65

3.75

3.85

3.95

4.05

4.15

4.25

4.35

4.45

4.55

F

H

K

L

M

N

P

R

S

T

U

V

X

Y

Z

④Represents production lot number

0 to 9, A to Z reverse character of 0 to 9, A to Z repeated (G,I,J,O,Q,W excepted)

281

XC6211/6219 Series

■MARKING RULE (Continued)

[XC6219 Series]

●SOT-25(SOT-23-5)

SOT-89-5

5

2

4

5

4

①

②

③

④

1

2

3

1

2

3

SOT-25

SOT-89-5

(TOP VIEW)

①Represents product series

MARK

L

PRODUCT SERIES

XC6219xxxxxx

②Represents type of regulator

MARK

PRODUCT SERIES

VOUT 100mV STEPS

VOUT 50mV STEPS

VOUT:0.1~3.0V VOUT:3.1~6.0V VOUT:0.15~3.05V VOUT:3.15~6.05V

V

X

Y

Z

A

B

C

D

E

F

H

K

L

M

N

P

XC6219Axxxxx

XC6219Bxxxxx

XC6219Cxxxxx

XC6219Dxxxxx

③Represents output voltage

OUTPUT VOLTAGE(V)

MARK

-

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.1

4.2

4.3

4.4

4.5

-

3.15

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

4.6 1.65 4.65

4.7 1.75 4.75

4.8 1.85 4.85

4.9 1.95 4.95

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

H

K

L

M

N

P

R

S

T

U

V

X

Y

Z

3.25

3.35

3.45

3.55

3.65

3.75

3.85

5.0 2.05

-

2.15

2.25

2.35

2.45

2.55

2.65

2.75

2.85

2.95

3.05

0.9

1.0

1.1

1.2

1.3

1.4

1.5

0.95 3.95

1.05 4.05

1.15 4.15

1.25 4.25

1.35 4.35

1.45 4.45

1.55 4.55

④Represents production lot number

0 to 9, A to Z reverse character of 0 to 9, A to Z repeated (G,I,J,O,Q,W excepted)

282

XC6211/6219

Series

■MARKING RULE (Continued)

●USP-6B

①②Represents product series

MARK

①

PRODUCT SERIES

XC6219xxxxDx

②

1

9

③Represents type of regulator

TYPE

PRODUCT SERIES

XC6219AxxxMx

XC6219BxxxMx

XC6219CxxxMx

XC6219DxxxMx

MARK

USP-6B

(TOP VIEW)

A

B

C

D

High Active, Pull-down resistor built-in (semi-custom)

High Active, No Pull-down resistor built-in (semi-custom)

Low Active, pull-up resistor built-in (semi-custom)

Low Active, No pull-up resistor built-in (semi-custom)

④Represents product series

VOLTAGE(V)

PRODUCT SERIES

MARK

3

5

3.X

5.X

XC6219x3xxDx

XC6219x5xxDx

③Represents output voltage

VOLTAGE PRODUCT SERIES SYMBOL VOLTAGE PRODUCT SERIES

MARK

0

1

2

3

4

5

6

7

8

9

X.0

X.1

X.2

X.3

X.4

X.5

X.6

X.7

X.8

X.9

XC6219xx0xDx

XC6219xx1xDx

XC6219xx2xDx

XC6219xx3xDx

XC6219xx4xDx

XC6219xx5xDx

XC6219xx6xDx

XC6219xx7xDx

XC6219xx8xDx

XC6219xx9xDx

A

B

C

D

E

F

H

K

L

X.05

X.15

X.25

X.35

X.45

X.55

X.65

X.75

X.85

X.95

XC6219xx0ADx

XC6219xx1ADx

XC6219xx2ADx

XC6219xx3ADx

XC6219xx4ADx

XC6219xx5ADx

XC6219xx6ADx

XC6219xx7ADx

XC6219xx8ADx

XC6219xx9ADx

M

⑥Represents production lot number

0 to 9, A to Z repeated (G,I,J,O,Q,W excepted)

* No character inversion used.

283

XC6211/6219 Series

■BLOCK DIAGRAM

■ABSOLUTE MAXIMUM RATINGS

Ta=25℃

PARAMETER

Input Voltage

Output Current

Output Voltage

CE Pin Voltage

SYMBOL

VIN

IOUT

VOUT

VCE

RATINGS

UNITS

7.0

500

V

mA

V

VSS - 0.3 ~ VIN + 0.3

250

V

SOT-25

SOT-89

USP-6B

Power Dissipation

Pd

mW

500

100

Operating Temperature Range

Storage Temperature Range

Topr

Tstg

- 40 ~ + 85

- 55 ~ + 125

℃

284

XC6211/6219

Series

■ELECTRICAL CHARACTERISTICS

●XC6211/6219B series

Ta=25℃

PARAMETER

SYMBOL

CONDITIONS

IOUT=30mA

MIN.

TYP.

MAX.

UNITS CIRCUIT

Output Voltage (*2)

Maximum Output Current

Load Regulation

VOUT(E)

IOUTMAX

UVOUT

Vdif1

Vdif2

IDD

×0.98 VOUT(T) ×1.02

150

-

V

①

-

15

E-1

E-2

25

-

50

mA

mV

μA

1mA≦IOUT≦100mA

IOUT=30mA

IOUT=100mA

VCE=VIN

VCE=VSS

Dropout Voltage (*3)

①

Supply Current

Standby Current

-

50

0.10

②

Istby

0.01

UVOUT

VOUT(T)+1.0V≦VIN≦7.0V

Line Regulation

Input Voltage

-

0.01

-

0.20

6.0

%/V

V

①

-

UVIN・VOUT IOUT=30mA

VIN

2.0

Output Voltage Temperature

Characteristics

UVOUT

IOUT=30mA

-40℃≦Topr≦85℃

-

100

-

ppm/℃

①

UTopr^・VOUT

Ripple Rejection Rate

PSRR

Ilim

IOUT=50mA, f=1kHz

-

65

300

50

-

dB

mA

V

μA

④

①

②

Current Limiter

Short Circuit Current

EN ‘High’ Voltage

EN ‘Low’ Voltage

EN ‘High’ Current

EN ‘Low’ Current

Ishort

VCEH

VCEL

ICEH

ICEL

1.60

-

-0.10

VIN

0.25

0.10

VCE=VIN

VCE=VSS

-

NOTE:

* 1: VOUT(T) = Specified output voltage

* 2: VOUT(E) = Effective output voltage

(I.e. the output voltage when "VOUT(T)+1.0V" is provided at the VIN pin while maintaining a certain IOUT value.)

(*5)

(*4)

* 3: Vdif={VIN1 -VOUT1

}

* 4: VOUT=A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VOUT(T)+1.0V} is input.

* 5: VIN=The Input Voltage when VOUT appears as Input Voltage is gradually decreased.

* 6: Unless otherwise stated, VIN=VOUT(T)+1.0V.

●Dropout Voltage Chart

E-1

E-2

SYMBOL

PARAMETER

Vdif1

Vdif2

MIN.

TYP.

MAX.

MIN.

TYP.

MAX.

OUTPUT VOLTAGE

0.9

1.50

1100

500

200

100

-

1100

500

200

120

80

70

60

50

1110

510

210

150

120

100

90

1100

500

200

100

-

1150

550

300

280

240

220

200

180

160

1200

600

400

380

350

330

310

290

270

250

230

210

1.80 ~ 1.85

1.90 ~ 1.95

2.00 ~ 2.05

2.10 ~ 2.25

2.30 ~ 2.45

2.50 ~ 2.75

2.80 ~ 2.95

3.00 ~ 3.05

3.10 ~ 3.95

4.00 ~ 4.95

5.00

90

80

70

* The input voltage 2.0V (MIN.) is needed to operate the series.

When the output voltage is less than 2.0V, 2.0V-VOUT(T) of dropout voltage is needed at minimum.

285

XC6211/6219 Series

■TEST CIRCUITS

Circuit ①

VIN

CE

VOUT

A

CL=1.0μF

CIN=1.0μF

(ceramic)

RL

VSS

V

Circuit ②

VIN

CE

VOUT

A

OPEN

A

VSS

Circuit ③

VIN

CE

VOUT

CIN=1.0µF

(ceramic)

CL=1.0µF

(ceramic)

F.F.T

VSS

IOUT=10mA

Circuit ④

VIN

CE

VOUT

IOUT=50mA

CL=1.0µF

(ceramic)

VSS

V

VIN={VOUT+1}VDC

+0.5Vp-pAC

286

XC6211/6219

Series

■OPERATIONAL EXPLANATION

The voltage divided by resistors R1 & R2 is compared with the internal reference voltage by the error amplifier. The

P-channel MOSFET, which is connected to the VOUT pin, is then driven by the subsequent output signal. The output

voltage at the VOUT pin is controlled and stabilized by a system of negative feedback. The current limit circuit and short

protect circuit operate in relation to the level of output current. Further, the IC's internal circuitry can be shutdown via the

CE pin's signal

With the XC6211/19 series, a stable output voltage is achievable even if used with low ESR capacitors as a phase

compensation circuit is built-in. In order to ensure the effectiveness of the phase compensation, we suggest that an output

capacitor (CL) is connected as close as possible to the output pin (VOUT) and the VSS pin. Please use an output capacitor

with a capacitance value of at least 1μF. Also, please connect an input capacitor (CIN) of 0.1μF between the VIN pin and

the VSS pin in order to ensure a stable power input.

The XC6211/19 series includes a combination of a fixed current limiter circuit & a foldback circuit which aid the operations

of the current limiter and circuit protection. When the load current reaches the current limit level, the fixed current limiter

circuit operates and output voltage drops. As a result of this drop in output voltage, the foldback circuit operates, output

voltage drops further and output current decreases. When the output pin is shorted, a current of about 50mA flows.

The IC's internal circuitry can be shutdown via the signal from the CE pin with the XC6211/19 series. In shutdown mode,

output at the VOUT pin will be pulled down to the VSS level via R1 & R2. The operational logic of the IC's CE pin is

selectable (please refer to the selection guide). Note that as the standard XC6211/19B type's regulator 1 and 2 are both '

High Active/No Pull-Down', operations will become unstable with the CE pin open. Although the CE pin is equal to an

inverter input with CMOS hysteresis, with either the pull-up or pull-down options, the CE pin input current will increase

when the IC is in operation. We suggest that you use this IC with either a VIN voltage or a VSS voltage input at the CE pin. If

this IC is used with the correct specifications for the CE pin, the operational logic is fixed and the IC will operate normally.

However, supply current may increase as a result of through current in the IC's internal circuitry.

■NOTES ON USE

1. Please use this IC within the stated absolute maximum ratings. The IC is liable to malfunction should the ratings be exceeded.

2. Where wiring impedance is high, operations may become unstable due to noise and/or phase lag depending on output

current. Please keep the resistance low between VIN and VSS wiring in particular.

3. Please wire the input capacitor (CIN) and the output capacitor (CL) as close to the IC as possible

287

XC6211/6219 Series

■TYPICAL PERFORMANCE CHARACTERISTICS

(1) Output Voltage vs. Output Current

XC6219x182

VIN=2.8V

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN

C

=

IN

1

=

u

1

F

μ

(c

F

er

(

a

c

m

er

i

a

c

m

s)

i

,

c)

C

,

L

C

=

L

1

=

uF (ceracemics)ic)

1 F ( ram

μ

2.0

1.5

1.0

0.5

0.0

2.0

1.5

1.0

0.5

0.0

VIN=2.8V

VIN=4.8V

VIN=3.8V

Topr=85℃

O

Topr= 85 C

25℃_O

25 C

O

-40℃

- 40 C

VIN=2.1V

0

50

100 150 200 250 300 350 400

Output Current IOUT (mA)

0

50

100 150 200 250 300 350 400

Output Current IOUT (mA)

XC6219x252

VIN=3.5V

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramc), CL=1μF (ceramic)

3.0

2.5

2.0

1.5

1.0

0.5

0.0

3.0

2.5

2.0

1.5

1.0

0.5

0.0

VIN=4.5V

VIN=5.5V

Topr=85℃

VIN=3.5V

VIN=2.8V

25℃

-40℃

0

50

100 150 200 250 300 350 400

Output Current IOUT (mA)

0

50

100 150 200 250 300 350 400

Output Current IOUT (mA)

XC6219x302

VIN=4.0V

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

4.0

3.5

3.0

2.5

2.0

1.5

1.0

0.5

0.0

4.0

3.5

3.0

2.5

2.0

1.5

1.0

0.5

0.0

VIN=4V

VIN=5V

VIN=6V

O

Topr=85℃

Topr= 85 C

VIN=3.3V

O

25 C

25℃

O

- 40 C

-40℃

0

50

100 150 200 250 300 350 400

Output Current IOUT (mA)

0

50

100 150 200 250 300 350 400

Output Current IOUT (mA)

288

XC6211/6219

Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(2) Output Voltage vs. Input Voltage

XC6219x182

O

Topr=25 C

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

2.0

1.8

1.6

1.4

1.2

1.0

1.90

1.85

1.80

1.75

1.70

1.65

IOUT=0mA

1mA

IOUT=0mA

1mA

30mA

100mA

3.0

4.0

5.0

6.0

1.3

1.8

2.3

Input Voltage VIN (V)

XC6219x252

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

XC6219x252

O

Topr=25 C

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

2.60

2.55

2.50

2.45

2.40

2.35

2.7

2.5

2.3

2.1

1.9

1.7

IOUT=0mA

1mA

IOUT=0mA

1mA

30mA

100mA

30mA

3.0

3.5

4.0

4.5

5.0

5.5

6.0

2

2.5

3

Input Voltage VIN (V)

XC6219x302

O

Topr=25 C

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

3.10

3.05

3.00

2.95

2.90

2.85

3.2

3.0

2.8

2.6

2.4

2.2

IOUT=0mA

1mA

IOUT=0mA

1mA

30mA

100mA

2.5

3

3.5

4.0

4.5

5.0

5.5

6.0

Input Voltage VIN (V)

289

XC6211/6219 Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(3) Dropout Voltage vs. Output Current

XC6219x252

XC6219x182

CIN=1uF (ceramics), CL=1uF (ceramics)

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

1.0

0.8

0.6

0.4

0.2

0.0

1.0

0.8

0.6

0.4

0.2

0.0

O

Topr= 85 C

Topr=85℃

O

25 C

Topr=85℃

Topr= 85 C

25℃_O

O

- 40 C

25 C

25℃

-40℃

O

- 40 C

-40℃

0

40

80

120

160

200

0

40

80

120

160

200

Output Current IOUT (mA)

XC6219x302

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

1.0

0.8

0.6

0.4

0.2

0.0

O

Topr= 85 C

Topr=85℃

O

25 C

25℃_O

- 40 C

-40℃

0

40

80

120

160

200

Output Current IOUT (mA)

(4) Supply Current vs. Input Voltage

XC6219x182

XC6219x252

50.0

40.0

30.0

20.0

50.0

40.0

30.0

20.0

10.0

0.0

O

Topr=85℃

Topr= 85 C

Topr=85℃

O

25 C

25℃

25℃_O

O

10.0

0.0

- 40 C

-40℃

0

1

2

3

4

5

6

0

1

2

3

4

5

6

Input Voltage VIN (V)

290

XC6211/6219

Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(4) Supply Current vs. Input Voltage

XC6210x302

50.0

40.0

30.0

20.0

O

Topr=85℃

Topr= 85 C

O

25 C

25℃

O

10.0

0.0

- 40 C

-40℃

0

1

2

3

4

5

6

Input Voltage VIN (V)

(5) Output Voltage vs. Ambient Temperature

XC6219x252

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

XC6219x182

VIN=2.8V

VIN=3.5V

CIN=1μF (ceramic), CL=1μF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

2.60

2.55

2.50

2.45

2.40

2.35

2.30

1.90

1.85

1.80

1.75

1.70

1.65

1.60

IOUT=0mA

1mA

IOUT=0mA

1mA

30mA

100mA

-40

-20

0

20

40

60

80

100

-40

-20

0

20

40

60

80

100

O

Ambient Temperature Topr ( C)

XC6219x302

CIN=1uF (ceramics), CL=1uF (ceramics)

VIN=4.0V

CIN=1μF (ceramic), CL=1μF (ceramic)

3.10

3.05

3.00

2.95

2.90

2.85

2.80

IOUT=0mA

1mA

30mA

100mA

-40

-20

0

20

40

60

80

100

O

Ambient Temperature Topr ( C)

291

XC6211/6219 Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(6) Supply Current vs. Ambient Temperature

XC6219x182

XC6211/19X182

XC 19x252

XC621162/19X252

VIN=2.8V

VIN=3.5V

50.0

40.0

30.0

20.0

10.0

0.0

50.0

40.0

30.0

20.0

10.0

0.0

-40

-20

0

20

40

60

80

100

-40

-20

0

20

40

60

80

100

O

Ambient Temperature Topr ( C)

O

Ambient Temperature Topr ( C)

XC6219x302

XC6211/19X302

VIN=4.0V

50.0

40.0

30.0

20.0

10.0

0.0

-40

-20

0

20

40

60

80

100

O

Ambient Temperature Topr ( C)

292

XC6211/6219

Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(7) Input Transient Response

XC6219x182

XC6211/19X182

XC6211/19x182

CL=1uF (ceramics), IOUT=1mA

CIN=1μF (ceramic), IOUT=1mA

XC6219x182

XC6211/19X182

XC6211/19x182

tr = tf = 5use

Tr=tf=5use

CL=1uF (ceramics), IOUT=10mA

CIN=1μF (ceramic), IOUT=10mA

5

4

1.88

1.86

1.84

1.82

1.80

1.78

1.76

5

4

1.88

1.86

1.84

1.82

1.80

1.78

1.76

Input Voltage

3

2

1

Output Voltage

0

-1

Time (40usec/div)

XC6211/19X252

XC6219x252

XC6211/19X182

XC6219x182

XC6211/19x182

XC6211/19x252 _{tr = tf = 5use}

tr = tf = 5use

Tr=tf=5use

CL=1uF (ceramics), IOUT=100mA

CIN=1μF (ceramic), IOUT=100mA

CL=1uF (ceramics), IOUT=1mA

CIN=1μF (ceramic), IOUT=1mA

5

4

1.88

1.86

1.84

1.82

1.80

1.78

1.76

5

2.58

2.56

2.54

2.52

2.50

2.48

2.46

4

3

Input Voltage

3

2

1

Output Voltage

0

Output Voltage

0

-1

Time (40usec/div)

XC6219x252

XC6211/19X252

XC6211/19x252

CIN=1μF (ceramic), IOUT=100mA

CL=1uF (ceramics), IOUT=100mA

XC6211/19X252

XC6211/19x252_{tr = tf = 5use}

tr = tf = 5use

Tr=tf=5use

CL=1uF (ceramics), IOUT=10mA

CIN=1μF (ceramic), IOUT=10mA

5

4

2.58

2.56

2.54

2.52

2.50

2.48

2.46

5

2.58

2.56

2.54

2.52

2.50

2.48

2.46

4

3

Input Voltage

3

2

1

Output Voltage

0

Output Voltage

0

-1

Time (40usec/div)

293

XC6211/6219 Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(7) Input Transient Response (Continued)

XC6219x302

XC6211/19X302

XC6211/19x302

tr=tf=5use

tr = tf = 5use

tr=tf=5use

tr = tf = 5use

CL=1μF (ceramic), IOUT=1mA

C

L

=

1uF (c(ceraramicics), IOUT=10mA

1 F e m ), IOUT=10mA

μ

CL=1uF (ceramics), IOUT=1mA

6

5

4

3

2

1

0

3.08

3.06

3.04

3.02

3.00

2.98

2.96

6

5

4

3

2

1

0

3.08

3.06

3.04

3.02

3.00

2.98

2.96

Input Voltage

Output Voltage

Time (40usec/div)

XXCC61211/91x93X03202

62

XC6211/19x302

trr=tf=5use

tr = tf = 5use

CL=1μF (ceramic), IOUT=100mA

CL=1uF (ceramics), IOUT=100mA

6

3.08

3.06

3.04

3.02

3.00

2.98

2.96

5

4

3

2

1

0

Input Voltage

Output Voltage

Time (40usec/div)

(8) Load Transient Response

XC6211/19X182

XC6219x182

XC6211/19x182

XC6219x182

XC6211/19x182

XC6211/19X182

trr=tf=5use

VIN=2.8V, tr = tf = 5use

VIN=2.8V, trr=tf=5use

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

2.0

1.9

1.8

1.7

1.6

1.5

1.4

300

2.0

1.9

1.8

1.7

1.6

1.5

1.4

300

250

200

150

100

50

250

200

150

100

50

Output Voltage

Output Current

Output Voltage

Output Current

100mA

50mA

10mA

0

Time (40usec/div)

294

XC6211/6219

Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(8) Load Transient Response (Continued)

XC6211/19X252

XC6211/19X182

XC6219x252

XC6219x182

XC6211/_V1_I9_Nx₌₃2_.5_5V2_{, tr = tf = 5use}

XC6211/_V1_I9_Nx₌₂1_.8_8V2_{, tr = tf = 5use}

VIN=3.5V, trr=tf=5use

VIN=2.8V, trr=tf=5use

CIN=1uF (ceramics), CL=1uF (ceramics)

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CL=1μF (ceramic), CL=1uF (ceramic)

2.7

2.6

2.5

2.4

2.3

2.2

2.1

300

250

200

150

100

50

2.0

1.9

1.8

1.7

1.6

1.5

1.4

300

250

200

150

100

50

Output Voltage

Output Current

Output Voltage

Output Current

100mA

50mA

10mA

0

Time (40usec/div)

XC6211/19X252

XC6219x252

XC6211/19x252

XC6219x252

XC6211/19x252

VIN=3.5V, trr=tf=5use

VIN=3.5V, tr = tf = 5use

VIN=3.5V, trr=tf=5use

VIN=3.5V, tr = tf = 5use

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

2.7

2.6

2.5

2.4

2.3

2.2

2.1

300

250

200

150

100

50

2.7

2.6

2.5

2.4

2.3

2.2

2.1

300

250

200

150

100

50

Output Voltage

Output Current

100mA

50mA

100mA

10mA

0

Time (40usec/div)

XC6211/19X302

XC6219x302

XC6211/19X302

XC6211/19x302

XC6219x302

XC6211/19x302

VIN=4.0V, tr = tf = 5use

VIN=4.0V, trr=tf=5use

CIN=1uF (ceramics), CL=1uF (ceramics)

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=C1Lu=F1μ(ceFra(cmeircasm),icC),L=C1Lu=F1u(cFe(rcaemraicmsi)c)

3.2

3.1

3.0

2.9

2.8

2.7

2.6

300

250

200

150

100

50

3.2

3.1

3.0

2.9

2.8

2.7

2.6

300

250

200

150

100

50

Output Voltage

Output Current

Output Voltage

Output Current

100mA

50mA

10mA

0

Time (40usec/div)

295

XC6211/6219 Series

■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

(8) Load Transient Response (Continued)

XC6211/19X302

XC6219x302

XC6211/19x302

VIN=4.0V, trr=tf=5use

VIN=4.0V, tr = tf = 5use

CL=1μF (ceramic), CL=1uF (ceramic)

CIN=1uF (ceramics), CL=1uF (ceramics)

3.2

3.1

3.0

2.9

2.8

2.7

2.6

300

250

200

150

100

50

Output Voltage

Output Current

100mA

10mA

0

Time (40usec/div)

(11) Ripple Rejection Rate

XC6211/19X252

XC6219x182

XC6219x252

XC6211/19x252

XC6211/19X18

XC6211/19x252

VIN=2.8V, DC+1Vp-pAC

VIN=3.5V, DC+1Vp-pAC

VIN=2.8V, DC+1Vp-pAC

IOUT=50mA, CL=1uF (ceramic)

IOUT=50mA, CL=1uF (ceramics)

IOIOUUTT==5500mmAA, ,CCLL==11uuFF(c(ceerarammicics))

100

90

80

70

60

50

40

30

20

10

0

100

90

80

70

60

50

40

30

20

10

0

0.01

0.1

1

10

100

0.01

0.1

1

10

100

Ripple Frequency f (kHz)

XC6211/19X302

XC6219x302

XC6211/19x302

VIN=3.0V, DC+1Vp-pAC

VIN=2.8V, DC+1Vp-pAC

IOUT=50mA, CL=1uF (ceramics)

IOUT=50mA, CL=1uF (ceramic)

100

90

80

70

60

50

40

30

20

10

0

0.01

0.1

1

10

100

Ripple Frequency f (kHz)

296


型号：	XC6211A36ADL
厂家：	Torex Semiconductor
描述：	Regulator
文件：	总20页 (文件大小：395K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

XC6211A36ADL [TOREX]

相关型号：

XC6211A36ADR

XC6211A36APR

XC6211A372PR

XC6211A37ADL

XC6211A37APR

XC6211A382PL

XC6211A38APL

XC6211A38APR

XC6211A39APR

XC6211A3AML

XC6211A3AMR

XC6211A402PR