XC9237A0BCMR
更新时间:2024-09-18 06:21:47
品牌:TOREX
描述:600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters
XC9237A0BCMR 概述
600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters 600毫安驱动Tr的。内置的同步降压型DC / DC转换器 开关式稳压器或控制器
XC9237A0BCMR 规格参数
是否Rohs认证: | 符合 | 生命周期: | Active |
包装说明: | , | Reach Compliance Code: | compliant |
风险等级: | 5.77 | 湿度敏感等级: | 1 |
Base Number Matches: | 1 |
XC9237A0BCMR 数据手册
通过下载XC9237A0BCMR数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载XC9235/XC9236/XC9237Series
ETR0514-007
600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters
☆GreenOperation Compatible
■GENERAL DESCRIPTION
The XC9235/XC9236/XC9237 series is a group of synchronous-rectification type DC/DC converters with a built-in 0.42Ω
P-channel driver transistor and 0.52ΩN-channel switching transistor, designed to allow the use of ceramic capacitors. The ICs
enable a high efficiency, stable power supply with an output current of 600mA to be configured using only a coil and two
capacitors connected externally. Operating voltage range is from 2.0V to 6.0V. Output voltage is internally set in a range from
0.8V to 4.0V in increments of 50mV (accuracy: ±2.0%). With the built-in oscillator, ether 1.2MHz or 3.0MHz can be selected
for suiting to your particular application. As for operation mode, the XC9235 series is PWM control, the XC9236 series is
automatic PWM/PFM switching control and the XC9237 series can be manually switched between the PWM control mode and
the automatic PWM/PFM switching control mode, allowing fast response, low ripple and high efficiency over the full range of
loads (from light load to heavy load).
The soft start and current control functions are internally optimized. During stand-by, all circuits are shutdown to reduce
current consumption to as low as 1.0μA or less. With the built-in UVLO (Under Voltage Lock Out) function, the internal
P-channel driver transistor is forced OFF when input voltage becomes 1.4V or lower.
The XC9235B/XC9236B/XC9237B series provide short-time turn-on by the soft start function internally set in 0.25 ms (TYP).
The XC9235B(C)/XC9236B(C)/XC9237B(C) integrate CL auto discharge function which enables the electric charge at the output
capacitor CL to be discharged via the internal auto-discharge switch located between the LX and VSS pins. When the devices
enter stand-by mode, output voltage quickly returns to the VSS level as a result of this function.
Two types of package SOT-25 and USP-6C are available.
■FEATURES
■APPLICATIONS
●Mobile phones
●Bluetooth equipment
P-ch Driver Transistor Built-In : ON resistance 0.42Ω
N-ch Driver Transistor Built-In : ON resistance 0.52Ω
Input Voltage
: 2.0V ~ 6.0V
●PDAs, portable communication modem
●Portable games
Output Voltage
: 0.8V ~ 4.0V
High Efficiency
: 92% (TYP.)
●Digital cameras, video cameras
●Cordless phones
Output Current
: 600mA
Oscillation Frequency
Maximum Duty Cycle
Control Methods
: 1.2MHz, 3.0MHz (+15%)
: 100%
●Notebook computers
: PWM (XC9235)
PWM/PFM Auto (XC9236)
PWM/PFM Manual (XC9237)
Soft-Start Circuit Built-In
Current Limiter Circuit Built-In (Constant Current & Latching)
Low ESR Ceramic Capacitor Compatible
Packages
: SOT-25, USP-6C
CL High Speed Discharge
(XC9235B(C)/XC9236B(C)/XC9237B(C) Series)
High Speed Soft Start
(XC9235B/XC9236B/XC9237B Series)
* Performance depends on external components and wiring on the PCB.
■TYPICAL APPLICATION CIRCUIT
■TYPICAL PERFORMANCE
CHARACTERISTICS
●Efficiency vs. Output Current(FOSC=1.2NHz, VOUT=1.8V)
PWM/PFM Automatic Sw itching Control
100
90
80
VIN= 4.2V
70
PWM Control
VIN= 4.2V
3.6V
2.4V
60
50
40
30
20
10
0
3.6V
2.4V
0.1
1
10
100
1000
Output Current:IOUT(mA)
1/28
XC9235/XC9236/XC9237 Series
■PIN CONFIGURATION
Lx
VOUT
5
4
* Please short the VSS pin (No. 2 and 5).
The dissipation pad for the USP-6C
1
Lx
VIN
VSS
6
5
*
package should be solder-plated in
recommended mount pattern and metal
masking so as to enhance mounting strength
and heat release. If the pad needs to be
connected to other pins, it should be
connected to the VSS (No. 5) pin.
2
3
VSS
CE/MODE
4
VOUT
1
2
3
VIN
VSS
CE/MODE
SOT-25
(Top View)
USP-6C
(BOTTOM VIEW)
■PIN ASSIGNMENT
PIN NUMBER
PIN NAME
FUNCTION
SOT-25
USP-6C
1
2
3
4
5
6
2, 5
4
3
1
VIN
VSS
CE / MODE
VOUT
Power Input
Ground
Chip Enable Mode Switch
Output Voltage Sense
Switching Output
Lx
■PRODUCT CLASSIFICATION
●Ordering Information
XC9235①②③④⑤⑥
XC9236①②③④⑤⑥
XC9237①②③④⑤⑥
PWM fixed control
PWM / PFM automatic switching control
PWM fixed controlQPWM / PFM automatic switching, manual switching
DESIGNATOR
DESCRIPTION
SYMBOL
A
DESCRIPTION
: CE input logic High Active
Transistor built-in,
Output voltage internally set
(VOUT product),
①.
B
C
: CE input logic High Active, high speed soft start, CL discharge
: CE input logic High Active, CL discharge
Soft-start internally set
: Integer number of output voltage
e.g. VOUT=2.8V→②=2, VOUT=3.3V→②=3
: Decimal number of output voltage
50mV increments: 0.05=A, 0.15=B, 0.25=C, 0.35=D, 0.45=E,
0.55=F, 0.65=H, 0.75=K, 0.85=L, 0.95=M
e.g. VOUT=2.8V→②=2, ③=8
②
③
Output Voltage
Output Voltage
0~4
0~9, A~M
VOUT=2.85V→②=2, ③=L
C
D
M
E
R
L
: 1.2MHz
④
⑤
⑥
Oscillation Frequency
Packages
: 3.0MHz
: SOT-25 (SOT-23-5)
: USP-6C
: Embossed tape, standard feed
: Embossed tape, reverse feed
Device Orientation
2/28
XC9235/XC9236/XC9237
Series
■BLOCK DIAGRAM
●XC9235A / XC9236A / XC9237A
●XC9235B(C) / XC9236B(C) / XC9237B(C)
NOTE: The signal from CE/MODE Control Logic to PWM/PFM Selector is being fixed to "L" level inside,
and XC9235 series chooses only PWM control.
The signal from CE/MODE Control Logic to PWM/PFM Selector is being fixed to "H" level inside,
and XC9236 series chooses only PWM/PFM automatic switching control.
Diodes inside the circuit are ESD protection diodes and parasitic diodes.
■ABSOLUTE MAXIMUM RATINGS
Ta=25℃
UNIT
PARAMETER
VIN Pin Voltage
SYMBOL
VIN
RATINGS
- 0.3 ~ 6.5
- 0.3 ~ VIN + 0.3 or 6.5V
- 0.3 ~ 6.5
- 0.3 ~ 6.5
±1500
V
V
Lx Pin Voltage
VLx
VOUT Pin Voltage
CE / MODE Pin Voltage
Lx Pin Current
VOUT
VCE
V
V
ILx
mA
Power Dissipation
SOT-25
USP-6C
250
Pd
mW
(*Ta=25℃)
100
Operating Temperature Range
Storage Temperature Range
Topr
Tstg
- 40 ~ + 85
- 55 ~ + 125
OC
OC
3/28
XC9235/XC9236/XC9237 Series
■ELECTRICAL CHARACTERISTICS
XC9237A18Cxx, VOUT=1.8V, FOSC=1.2MHz, Ta=25℃
PARAMETER
SYMBOL
CONDITIONS
MIN. TYP. MAX. UNIT CIRCUIT
When connected to external components,
VIN=VCE=5.0V, IOUT=30mA
Output Voltage
VOUT
VIN
1.764 1.800 1.836
V
V
①
①
①
Operating Voltage Range
Maximum Output Current
2.0
-
-
6.0
-
VIN=VOUT(E)+2.0V, VCE=1.0V,
IOUTMAX
600
mA
When connected to external components (*9)
VCE =VIN, VOUT=0V,
U.V.L.O. Voltage
VUVLO
1.00 1.40 1.78
V
②
Voltage which Lx pin holding “L” level (*1, *11)
Supply Current
Stand-by Current
IDD
ISTB
VIN=VCE=5.0V, VOUT=VOUT(E)×1.1V
VIN=5.0V, VCE=0V, VOUT=VOUT(E)×1.1V
-
-
15
0
33
1.0
μA
μA
③
③
When connected to external components,
VIN=VOUT(E)+2.0V, VCE =1.0V, IOUT=100mA
Oscillation Frequency
PFM Switching Current
FOSC
IPFM
1020 1200 1380 kHz
①
①
When connected to external components,
120
160
200
mA
VIN=VOUT(E)+2.0V, VCE =VIN, IOUT=1mA (*12)
Maximum IPFM Limit
Maximum Duty Cycle
Minimum Duty Cycle
MAXIPFM
MAXDTY
MINDTY
VCE=VIN=(C-1), IOUT=1mA (*12)
200
-
-
%
%
%
①
②
②
VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V
VIN=VCE=5.0V, VOUT=VOUT(E)×1.1V
100
-
-
0
When connected to external components,
VCE=VIN=VOUT(E)+1.2V, IOUT=100mA
Efficiency (*2)
EFFI
-
92
-
%
①
Lx SW "H" ON Resistance 1
Lx SW "H" ON Resistance 2
Lx SW "L" ON Resistance 1
Lx SW "L" ON Resistance 2
Lx SW "H" Leak Current (*5)
Lx SW "L" Leak Current (*5)
Current Limit (*10)
RLxH
RLxH
VIN=VCE=5.0V, VOUT=0V, ILx=100mA (*3)
VIN=VCE=3.6V, VOUT=0V, ILx=100mA (*3)
VIN=VCE=5.0V (*4)
-
-
-
-
-
-
0.35 0.55
0.42 0.67
0.45 0.66
0.52 0.77
Ω
Ω
④
④
④
-
RLxL
Ω
RLxL
VIN=VCE=3.6V (*4)
Ω
ILeakH
ILeakL
ILIM
VIN=VOUT=5.0V, VCE=0V, Lx=0V
VIN=VOUT=5.0V, VCE=0V, Lx=5.0V
VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V (*8)
0.01
0.01
1.0
1.0
μA
μA
mA
⑤
⑤
⑥
900 1050 1350
Output Voltage
Temperature Characteristics VOUT・△topr
△VOUT
IOUT=30mA, -40℃≦Topr≦85℃
-
±100
-
ppm/
℃
①
③
③
VOUT=0V, Applied voltage to VCE
,
CE "H" Voltage
CE "L" Voltage
VCEH
VCEL
0.65
VSS
-
-
VIN
V
Voltage changes Lx to “H” level (*11)
VOUT=0V, Applied voltage to VCE
,
0.25
V
Voltage changes Lx to “L” level (*11)
When connected to external components,
I
OUT=1mA (*6), Voltage which oscillation
VIN -
1.0
PWM "H" Level Voltage
VPWMH
-
-
V
①
frequency becomes 1020 kHz≦FOSC≦
1380kHz (*13)
When connected to external components,
IOUT=1mA (*6), Voltage which oscillation
frequency becomes FOSC<1020kHz (*13)
VIN=VCE=5.0V, VOUT=0V
VIN –
0.25
PWM "L" Level Voltage
VPWML
-
-
V
①
CE "H" Current
CE "L" Current
ICEH
ICEL
- 0.1
- 0.1
-
-
0.1
0.1
μA
μA
⑤
⑤
VIN=5.0V, VCE=0V, VOUT=0V
When connected to external components,
Soft Start Time
TSS
0.5
1.0
2.5
ms
①
⑦
VCE=0V → VIN, IOUT=1mA
VIN=VCE=5.0V, VOUT=0.8×VOUT(E)
,
Latch Time
TLAT
1.0
-
20.0
ms
Short Lx at 1Ω resistance (*7)
Sweeping VOUT, VIN=VCE=5.0V, Short Lx at
1Ω resistance, VOUT voltage which Lx
becomes “L” level within 1ms
Short Protection
Threshold Voltage
VSHORT
0.675 0.900 1.150
V
⑦
Test conditions: Unless otherwise stated, VIN=5.0V, VOUT(E)=Setting Voltage
NOTE:
*1: Including hysteresis operating voltage range.
*2: EFFI = { ( output voltage×output current ) / ( input voltage×input current) }×100
*3: ON resistance (Ω)= (VIN - Lx pin measurement voltage) / 100mA
*4: R&D value
*5: When temperature is high, a current of approximately 10μA (maximum) may leak.
*6:The CE/MODE pin of the XC9237A series works also as an external switching pin of PWM control and PWM/PFM control. When the IC is in the
operation, control is switched to the automatic PWM/PFM switching mode when the CE/MODE pin voltage is equal to or greater than VIN minus
0.3V, and to the PWM mode when the CE/MODE pin voltage is equal to or lower than VIN minus 1.0V and equal to or greater than VCEH.
*7:Time until it short-circuits VOUT with GND via 1Ωof resistor from an operational state and is set to Lx=0V from current limit pulse generating.
*8: When VIN is less than 2.4V, limit current may not be reached because voltage falls caused by ON resistance.
*9: When the difference between the input and the output is small, some cycles may be skipped completely before current maximizes.
If current is further pulled from this state, output voltage will decrease because of P-ch driver ON resistance.
*10: Current limit denotes the level of detection at peak of coil current.
*11: “H”=VIN~VIN-1.2V, “L”=+0.1V~-0.1V
*12: XC9235 series exclude IPFM and MAXIPFM because those are only for the PFM control’s functions.
*13: XC9235/9236 series exclude VPWMH and VPWML because those are only for the XC9237 series’ functions.
4/28
XC9235/XC9236/XC9237
Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9237A18Dxx, VOUT=1.8V, FOSC=3.0MHz, Ta=25℃
PARAMETER
SYMBOL
CONDITIONS
MIN. TYP. MAX. UNIT CIRCUIT
When connected to external components,
VIN=VCE=5.0V, IOUT=30mA
Output Voltage
VOUT
VIN
1.764 1.800 1.836
V
V
①
①
①
Operating Voltage Range
Maximum Output Current
2.0
-
-
6.0
-
VIN=VOUT(E)+2.0V, VCE=1.0V,
IOUTMAX
600
mA
When connected to external components (*9)
VCE=VIN, VOUT=0V,
U.V.L.O. Voltage
VUVLO
1.00 1.40 1.78
V
③
Voltage which Lx pin holding “L” level (*1,*11)
Supply Current
Stand-by Current
IDD
ISTB
VIN=VCE=5.0V, VOUT=VOUT(E)×1.1V
VIN=5.0V, VCE=0V, VOUT=VOUT(E)×1.1V
-
-
21
0
35
1.0
μA
μA
②
②
When connected to external components,
VIN=VOUT(E)+2.0V, VCE=1.0V, IOUT=100mA
Oscillation Frequency
PFM Switching Current
FOSC
2550 3000 3450 kHz
①
①
When connected to external components,
IPFM
170
220
270
mA
VIN=VOUT(E)+2.0V, VCE=VIN, IOUT=1mA (*12)
Maximum IPFM Limit
Maximum Duty Cycle
Minimum Duty Cycle
MAXIPFM
VCE=VIN=(C-1), IOUT=1mA (*12)
-
100
-
200
-
-
300
-
0
%
%
%
①
③
③
MAXDTY VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V
MINDTY
VIN=VCE=5.0V, VOUT=VOUT(E)×0.1V
When connected to external components,
VCE=VIN=VOUT(E)+1.2V, IOUT=100mA
VIN=VCE=5.0V, VOUT =0V, ILx=100mA (*3)
Efficiency
EFFI
-
86
-
%
①
Lx SW "H" ON Resistance 1
Lx SW "H" ON Resistance 2
Lx SW "L" ON Resistance 1
Lx SW "L" ON Resistance 2
Lx SW "H" Leak Current (*5)
Lx SW "L" Leak Current (*5)
Current Limit (*10)
RLxH
RLxH
RLxL
-
-
-
-
-
-
0.35 0.55
0.42 0.67
0.45 0.66
0.52 0.77
Ω
Ω
④
④
-
VIN=VCE=3.6V, VOUT =0V, ILx=100mA (*3)
VIN=VCE=5.0V (*4)
Ω
RLxL
VIN=VCE=3.6V (*4)
Ω
-
ILeakH
ILeakL
ILIM
VIN=VOUT=5.0V, VCE=0V, Lx=0V
VIN=VOUT=5.0V, VCE=0V, Lx=5.0V
VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V (*8)
0.01
0.01
1.0
1.0
μA
μA
mA
⑤
⑤
⑥
900 1050 1350
Output Voltage
Temperature Characteristics VOUT・△topr
△VOUT
IOUT=30mA, -40℃≦Topr≦85℃
-
±100
-
ppm/
℃
①
③
③
VOUT=0V, Applied voltage to VCE
,
CE "H" Voltage
CE "L" Voltage
VCEH
VCEL
0.65
VSS
-
-
VIN
V
Voltage changes Lx to “H” level (*11)
VOUT=0V, Applied voltage to VCE
,
0.25
V
Voltage changes Lx to “L” level (*11)
When connected to external components,
I
OUT=1mA (*6), Voltage which oscillation
VIN -
1.0
PWM "H" Level Voltage
VPWMH
-
-
V
①
frequency becomes 2550kHz≦FOSC≦
3450kHz (*13)
When connected to external components,
IOUT=1mA (*6), Voltage which oscillation
frequency becomes FOSC<2550kHz (*13)
VIN=VCE=5.0V, VOUT=0V
VIN –
0.25
PWM "L" Level Voltage
VPWML
-
-
V
①
CE "H" Current
CE "L" Current
ICEH
ICEL
- 0.1
- 0.1
-
-
0.1
0.1
μA
μA
⑤
⑤
VIN=5.0V, VCE=0V, VOUT=0V
When connected to external components,
VCE=0V → VIN, IOUT=1mA
Soft Start Time
Latch Time
TSS
0.5
1.0
0.9
-
3.0
20
ms
ms
①
⑦
VIN=VCE=5.0V, VOUT=0.8×VOUT(E)
,
TLAT
Short Lx at 1Ω resistance (*7)
Sweeping VOUT, VIN=VCE=5.0V, Short Lx at
1Ω resistance, VOUT voltage which Lx
becomes “L” level within 1ms (*4)
Short Protection
Threshold Voltage
VSHORT
0.675 0.900 1.150
V
⑦
Test conditions: Unless otherwise stated, VIN=5.0V, VOUT(E)=Setting Voltage
NOTE:
*1: Including hysteresis operating voltage range.
*2: EFFI = { ( output voltage×output current ) / ( input voltage×input current) }×100
*3: ON resistance (Ω)= (VIN - Lx pin measurement voltage) / 100mA
*4: R&D value
*5: When temperature is high, a current of approximately 10μA (maximum) may leak.
*6:The CE/MODE pin of the XC9237A series works also as an external switching pin of PWM control and PWM/PFM control. When the IC is in the
operation, control is switched to the automatic PWM/PFM switching mode when the CE/MODE pin voltage is equal to or greater than VIN minus
0.3V, and to the PWM mode when the CE/MODE pin voltage is equal to or lower than VIN minus 1.0V and equal to or greater than VCEH.
*7:Time until it short-circuits VOUT with GND via 1Ωof resistor from an operational state and is set to Lx=0V from current limit pulse generating.
*8: When VIN is less than 2.4V, limit current may not be reached because voltage falls caused by ON resistance.
*9: When the difference between the input and the output is small, some cycles may be skipped completely before current maximizes.
If current is further pulled from this state, output voltage will decrease because of P-ch driver ON resistance.
*10: Current limit denotes the level of detection at peak of coil current.
*11: “H”=VIN~VIN-1.2V, “L”=+0.1V~-0.1V
*12: XC9235 series exclude IPFM and MAXIPFM because those are only for the PFM control’s functions.
*13: XC9235/9236 series exclude VPWMH and VPWML because those are only for the XC9237 series’ functions.
5/28
XC9235/XC9236/XC9237 Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9237B(C)18Cxx, VOUT=1.8V, FOSC=1.2MHz, Ta=25℃
PARAMETER
Output Voltage
SYMBOL
VOUT
CONDITIONS
MIN. TYP. MAX. UNIT CIRCUIT
When connected to external components,
VIN=VCE=5.0V, IOUT=30mA
1.764 1.800 1.836
V
V
①
①
①
Operating Voltage Range
Maximum Output Current
VIN
2.0
-
-
6.0
-
VIN=VOUT(E)+2.0V, VCE=1.0V,
IOUTMAX
600
mA
When connected to external components (*9)
VCE =VIN, VOUT=0V,
U.V.L.O. Voltage
VUVLO
1.00 1.40 1.78
V
②
Voltage which Lx pin holding “L” level (*1, *11)
Supply Current
Stand-by Current
IDD
ISTB
VIN=VCE=5.0V, VOUT=VOUT(E)×1.1V
VIN=5.0V, VCE=0V, VOUT=VOUT(E)×1.1V
-
-
15
0
33
1.0
μA
μA
③
③
When connected to external components,
VIN=VOUT(E)+2.0V, VCE =1.0V, IOUT=100mA
Oscillation Frequency
PFM Switching Current
FOSC
IPFM
1020 1200 1380 kHz
①
①
When connected to external components,
120
160
200
mA
VIN=VOUT(E)+2.0V, VCE =VIN, IOUT=1mA (*12)
Maximum IPFM Limit
Maximum Duty Cycle
Minimum Duty Cycle
MAXIPFM
MAXDTY
MINDTY
VCE=VIN=(C-1), IOUT=1mA (*12)
200
-
-
%
%
%
①
②
②
VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V
100
-
-
0
VIN=VCE=5.0V, VOUT=VOUT(E)×1.1V
When connected to external components,
VCE=VIN=VOUT(E)+1.2V, IOUT=100mA
Efficiency (*2)
EFFI
-
92
-
%
①
Lx SW "H" ON Resistance 1
Lx SW "H" ON Resistance 2
Lx SW "L" ON Resistance 1
Lx SW "L" ON Resistance 2
Lx SW "H" Leak Current (*5)
Current Limit (*10)
RLxH
RLxH
VIN=VCE=5.0V, VOUT=0V, ILx=100mA (*3)
VIN=VCE=3.6V, VOUT=0V, ILx=100mA (*3)
VIN=VCE=5.0V (*4)
-
-
-
-
-
0.35 0.55
0.42 0.67
0.45 0.66
0.52 0.77
Ω
Ω
④
④
④
-
RLxL
Ω
RLxL
VIN=VCE=3.6V (*4)
Ω
ILeakH
ILIM
VIN=VOUT=5.0V, VCE=0V, Lx=0V
VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V (*8)
0.01
1.0
μA
mA
⑤
⑥
900 1050 1350
Output Voltage
Temperature Characteristics VOUT・△topr
△VOUT
IOUT=30mA, -40℃≦Topr≦85℃
-
±100
-
ppm/
℃
①
③
③
VOUT=0V, Applied voltage to VCE
,
CE "H" Voltage
CE "L" Voltage
VCEH
VCEL
0.65
VSS
-
-
VIN
V
Voltage changes Lx to “H” level (*11)
VOUT=0V, Applied voltage to VCE
,
0.25
V
Voltage changes Lx to “L” level (*11)
When connected to external components,
VIN -
1.0
PWM "H" Level Voltage
VPWMH
IOUT=1mA (*6), Voltage which oscillation frequency
-
-
V
①
becomes 1020 kHz
≦FOSC≦
1380kHz (*13)
When connected to external components,
VIN –
0.25
PWM "L" Level Voltage
VPWML
IOUT=1mA (*6), Voltage which oscillation frequency
-
-
V
①
becomes FOSC
<
1020kHz (*13)
CE "H" Current
CE "L" Current
ICEH
ICEL
VIN=VCE=5.0V, VOUT=0V
VIN=5.0V, VCE=0V, VOUT=0V
- 0.1
- 0.1
-
-
0.1
0.1
μA
μA
⑤
⑤
When connected to external components,
Soft Start Time (B Series)
Soft Start Time (C Series)
Latch Time
TSS
TSS
TLAT
-
0.25 0.40
ms
ms
ms
①
①
⑦
VCE=0V → VIN, IOUT=1mA
When connected to external components,
CE=0V → VIN, IOUT=1mA
VIN=VCE=5.0V, VOUT=0.8 VOUT(E)
Short Lx at 1
resistance (*7)
Sweeping VOUT, VIN=VCE=5.0V, Short Lx at
0.5
1.0
1.0
-
2.5
V
×
,
20.0
Ω
Short Protection
Threshold Voltage
1
Ω resistance, VOUT voltage which Lx
VSHORT
0.675 0.900 1.150
200 300 450
V
⑦
⑧
becomes “L” level within 1ms
VIN=5.0V, LX=5.0V, VCE=0V, VOUT=open
CL Discharge
Rdischg
Ω
Test conditions: Unless otherwise stated, VIN=5.0V, VOUT(E)=Setting Voltage
NOTE:
*1: Including hysteresis operating voltage range.
*2: EFFI = { ( output voltage×output current ) / ( input voltage×input current) }×100
*3: ON resistance (Ω)= (VIN - Lx pin measurement voltage) / 100mA
*4: R&D value
*5: When temperature is high, a current of approximately 10μA (maximum) may leak.
*6:The CE/MODE pin of the XC9237A series works also as an external switching pin of PWM control and PWM/PFM control. When the IC is in the
operation, control is switched to the automatic PWM/PFM switching mode when the CE/MODE pin voltage is equal to or greater than VIN minus
0.3V, and to the PWM mode when the CE/MODE pin voltage is equal to or lower than VIN minus 1.0V and equal to or greater than VCEH.
*7:Time until it short-circuits VOUT with GND via 1Ωof resistor from an operational state and is set to Lx=0V from current limit pulse generating.
*8: When VIN is less than 2.4V, limit current may not be reached because voltage falls caused by ON resistance.
*9: When the difference between the input and the output is small, some cycles may be skipped completely before current maximizes.
If current is further pulled from this state, output voltage will decrease because of P-ch driver ON resistance.
*10: Current limit denotes the level of detection at peak of coil current.
*11: “H”=VIN~VIN-1.2V, “L”=+0.1V~-0.1V
*12: XC9235 series exclude IPFM and MAXIPFM because those are only for the PFM control’s functions.
*13: XC9235/9236 series exclude VPWMH and VPWML because those are only for the XC9237 series’ functions.
6/28
XC9235/XC9236/XC9237
Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9237B(C)18Dxx, VOUT=1.8V, FOSC=3.0MHz, Ta=25℃
PARAMETER
SYMBOL
CONDITIONS
MIN. TYP. MAX. UNIT CIRCUIT
When connected to external components,
VIN=VCE=5.0V, IOUT=30mA
Output Voltage
VOUT
VIN
1.764 1.800 1.836
V
V
①
①
①
Operating Voltage Range
Maximum Output Current
2.0
-
-
6.0
-
VIN=VOUT(E)+2.0V, VCE=1.0V,
IOUTMAX
600
mA
When connected to external components (*9)
VCE=VIN, VOUT=0V,
U.V.L.O. Voltage
VUVLO
1.00 1.40 1.78
V
③
Voltage which Lx pin holding “L” level (*1,*11)
Supply Current
Stand-by Current
IDD
ISTB
VIN=VCE=5.0V, VOUT=VOUT(E)×1.1V
VIN=5.0V, VCE=0V, VOUT=VOUT(E)×1.1V
-
-
21
0
35
1.0
μA
μA
②
②
When connected to external components,
VIN=VOUT(E)+2.0V, VCE=1.0V, IOUT=100mA
Oscillation Frequency
PFM Switching Current
FOSC
2550 3000 3450 kHz
①
①
When connected to external components,
IPFM
170
220
270
mA
VIN=VOUT(E)+2.0V, VCE=VIN, IOUT=1mA (*12)
Maximum IPFM Limit
Maximum Duty Cycle
Minimum Duty Cycle
MAXIPFM
VCE=VIN=(C-1), IOUT=1mA (*12)
-
100
-
200
-
-
300
-
0
%
%
%
①
③
③
MAXDTY VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V
MINDTY
VIN=VCE=5.0V, VOUT=VOUT(E)×0.1V
When connected to external components,
VCE=VIN=VOUT(E)+1.2V, IOUT=100mA
VIN=VCE=5.0V, VOUT =0V, ILx=100mA (*3)
Efficiency
EFFI
-
86
-
%
①
Lx SW "H" ON Resistance 1
Lx SW "H" ON Resistance 2
Lx SW "L" ON Resistance 1
Lx SW "L" ON Resistance 2
Lx SW "H" Leak Current (*5)
Current Limit (*10)
RLxH
RLxH
RLxL
RLxL
ILeakH
ILIM
-
-
-
-
-
0.35 0.55
0.42 0.67
0.45 0.66
0.52 0.77
Ω
Ω
④
④
-
-
⑤
⑥
VIN=VCE=3.6V, VOUT =0V, ILx=100mA (*3)
VIN=VCE=5.0V (*4)
Ω
VIN=VCE=3.6V (*4)
Ω
VIN=VOUT=5.0V, VCE=0V, Lx=0V
VIN=VCE=5.0V, VOUT=VOUT(E)×0.9V (*8)
0.01
1.0
μA
mA
900 1050 1350
Output Voltage
Temperature Characteristics VOUT・△topr
△VOUT
IOUT=30mA, -40℃≦Topr≦85℃
-
±100
-
ppm/
℃
①
③
③
VOUT=0V, Applied voltage to VCE
,
CE "H" Voltage
CE "L" Voltage
VCEH
VCEL
0.65
VSS
-
-
VIN
V
Voltage changes Lx to “H” level (*11)
VOUT=0V, Applied voltage to VCE
,
0.25
V
Voltage changes Lx to “L” level (*11)
When connected to external components,
IOUT=1mA (*6), Voltage which oscillation
frequency becomes 2550kHz≦FOSC≦
3450kHz (*13)
VIN -
1.0
PWM "H" Level Voltage
VPWMH
-
-
V
①
When connected to external components,
IOUT=1mA (*6), Voltage which oscillation
frequency becomes FOSC<2550kHz (*13)
VIN –
0.25
PWM "L" Level Voltage
VPWML
-
-
V
①
CE "H" Current
CE "L" Current
ICEH
ICEL
VIN=VCE=5.0V, VOUT=0V
VIN=5.0V, VCE=0V, VOUT=0V
- 0.1
- 0.1
-
-
0.1
0.1
μA
μA
⑤
⑤
When connected to external components,
Soft Start Time (B Series)
Soft Start Time (C Series)
Latch Time
TSS
TSS
TLAT
-
0.32 0.50
ms
ms
ms
①
①
⑦
VCE=0V → VIN, IOUT=1mA
When connected to external components,
CE=0V → VIN, IOUT=1mA
VIN=VCE=5.0V, VOUT=0.8 VOUT(E)
Short Lx at 1
resistance (*7)
Sweeping VOUT, VIN=VCE=5.0V, Short Lx at
resistance, VOUT voltage which Lx
0.5
1.0
0.9
-
2.5
20
V
×
,
Ω
Short Protection
Threshold Voltage
VSHORT
1
Ω
0.675 0.900 1.150
200 300 450
V
⑦
⑧
becomes “L” level within 1ms
VIN=5.0V, LX=5.0V, VCE=0V, VOUT=open
CL Discharge
Rdischg
Ω
Test conditions: Unless otherwise stated, VIN=5.0V, VOUT(E)=Setting Voltage
NOTE:
*1: Including hysteresis operating voltage range.
*2: EFFI = { ( output voltage×output current ) / ( input voltage×input current) }×100
*3: ON resistance (Ω)= (VIN - Lx pin measurement voltage) / 100mA
*4: R&D value
*5: When temperature is high, a current of approximately 10μA (maximum) may leak.
*6:The CE/MODE pin of the XC9237A series works also as an external switching pin of PWM control and PWM/PFM control. When the IC is in the
operation, control is switched to the automatic PWM/PFM switching mode when the CE/MODE pin voltage is equal to or greater than VIN minus
0.3V, and to the PWM mode when the CE/MODE pin voltage is equal to or lower than VIN minus 1.0V and equal to or greater than VCEH.
*7:Time until it short-circuits VOUT with GND via 1Ωof resistor from an operational state and is set to Lx=0V from current limit pulse generating.
*8: When VIN is less than 2.4V, limit current may not be reached because voltage falls caused by ON resistance.
*9: When the difference between the input and the output is small, some cycles may be skipped completely before current maximizes.
If current is further pulled from this state, output voltage will decrease because of P-ch driver ON resistance.
*10: Current limit denotes the level of detection at peak of coil current.
*11: “H”=VIN~VIN-1.2V, “L”=+0.1V~-0.1V
*12: XC9235 series exclude IPFM and MAXIPFM because those are only for the PFM control’s functions.
*13: XC9235/9236 series exclude VPWMH and VPWML because those are only for the XC9237 series’ functions.
7/28
XC9235/XC9236/XC9237 Series
■ELECTRICAL CHARACTERISTICS (Continued)
●PFM Switching Current (IPFM) by Oscillation Frequency and Setting Voltage
(mA)
MAX.
1.2MHz
3.0MHz
TYP.
260
SETTING VOLTAGE
MIN.
140
130
120
TYP.
180
170
160
MAX.
240
MIN.
190
180
170
VOUT(E) ≦1.2V
350
300
270
1.2V<VOUT(E) ≦1.75V
1.8V≦VOUT(E)
220
240
200
220
●Input Voltage (VIN) for Measuring Maximum PFM Switching Current (MAXIPFM) Limit
FOSC
C-1
1.2MHz
3.0MHz
VOUT(E)+0.5V
VOUT(E)+1.0V
Minimum operating voltage is 2.0V.
ex.) Although when VOUT(E) is 1.2V and FOSC is 1.2MHz, (C-1) should be 1.7V, (C-1) becomes 2.0V for the minimum operating voltage 2.0V.
●Soft-Start Time, Setting Voltage(XC9235B/36B/37B Series only)
SERIES
FOSC
SETTING VOLTAGE
0.8≦V OUT(E)<1.5
1.5≦V OUT(E)<1.8
1.8≦V OUT(E)<2.5
2.5≦V OUT(E)<4.0
0.8≦V OUT(E)<2.5
2.5≦V OUT(E)<4.0
0.8≦V OUT(E)<1.8
1.8≦V OUT(E)<4.0
MIN.
TYP.
250
320
280
320
280
320
280
320
MAX.
400μs
500μs
400μs
500μs
1200kHz
1200kHz
1200kHz
1200kHz
1200kHz
1200kHz
3000kHz
3000kHz
-
-
-
-
-
-
-
-
XC9235B/XC9237B
400μs
500μs
400μs
500μs
XC9236B
XC9235B/
XC9236B/XC9237B
■TYPICAL APPLICATION CIRCUIT
●FOSC=3.0MHz
L:
1.5μH
(NR3015, TAIYO YUDEN)
(Ceramic)
CIN:
CL:
4.7μF
10μF
(Ceramic)
●FOSC=1.2MHz
L:
4.7μH
4.7μF
10μF
(NR4018, TAIYO YUDEN)
(Ceramic)
CIN:
CL:
(Ceramic)
8/28
XC9235/XC9236/XC9237
Series
■OPERATIONAL DESCRIPTION
The XC9235/XC9236/XC9237 series consists of a reference voltage source, ramp wave circuit, error amplifier, PWM
comparator, phase compensation circuit, output voltage adjustment resistors, P-channel MOSFET driver transistor, N-channel
MOSFET switching transistor for the synchronous switch, current limiter circuit, U.V.L.O. circuit and others. (See the block
diagram above.) The series ICs compare, using the error amplifier, the voltage of the internal voltage reference source with the
feedback voltage from the VOUT pin through split resistors, R1 and R2. Phase compensation is performed on the resulting
error amplifier output, to input a signal to the PWM comparator to determine the turn-on time during PWM operation. The
PWM comparator compares, in terms of voltage level, the signal from the error amplifier with the ramp wave from the ramp
wave circuit, and delivers the resulting output to the buffer driver circuit to cause the Lx pin to output a switching duty cycle.
This process is continuously performed to ensure stable output voltage. The current feedback circuit monitors the P-channel
MOS driver transistor current for each switching operation, and modulates the error amplifier output signal to provide multiple
feedback signals. This enables a stable feedback loop even when a low ESR capacitor such as a ceramic capacitor is used
ensuring stable output voltage.
<Reference Voltage Source>
The reference voltage source provides the reference voltage to ensure stable output voltage of the DC/DC converter.
<Ramp Wave Circuit>
The ramp wave circuit determines switching frequency. The frequency is fixed internally and can be selected from 1.2MHz or
3.0MHz. Clock pulses generated in this circuit are used to produce ramp waveforms needed for PWM operation, and to
synchronize all the internal circuits.
<Error Amplifier>
The error amplifier is designed to monitor output voltage. The amplifier compares the reference voltage with the feedback
voltage divided by the internal split resistors, R1 and R2. When a voltage lower than the reference voltage is fed back, the
output voltage of the error amplifier increases. The gain and frequency characteristics of the error amplifier output are fixed
internally to deliver an optimized signal to the mixer.
<Current Limit>
The current limiter circuit of the XC9235/XC9236/XC9237 series monitors the current flowing through the P-channel MOS
driver transistor connected to the Lx pin, and features a combination of the current limit mode and the operation suspension
mode.
① When the driver current is greater than a specific level, the current limit function operates to turn off the pulses from the Lx
pin at any given timing.
② When the driver transistor is turned off, the limiter circuit is then released from the current limit detection state.
③ At the next pulse, the driver transistor is turned on. However, the transistor is immediately turned off in the case of an over
current state.
④ When the over current state is eliminated, the IC resumes its normal operation.
The IC waits for the over current state to end by repeating the steps ① through ③. If an over current state continues for a
few ms and the above three steps are repeatedly performed, the IC performs the function of latching the OFF state of the
driver transistor, and goes into operation suspension mode. Once the IC is in suspension mode, operations can be
resumed by either turning the IC off via the CE/MODE pin, or by restoring power to the VIN pin. The suspension mode does
not mean a complete shutdown, but a state in which pulse output is suspended; therefore, the internal circuitry remains in
operation. The current limit of the XC9235/XC9236/XC9237 series can be set at 1050mA at typical. Besides, care must
be taken when laying out the PC Board, in order to prevent misoperation of the current limit mode. Depending on the state
of the PC Board, latch time may become longer and latch operation may not work. In order to avoid the effect of noise, the
board should be laid out so that input capacitors are placed as close to the IC as possible.
9/28
XC9235/XC9236/XC9237 Series
■OPERATIONAL DESCRIPTION (Continued)
<Short-Circuit Protection>
The short-circuit protection circuit monitors the internal R1 and R2 divider voltage from the VOUT pin (refer to FB point in
the block diagram shown in the previous page). In case where output is accidentally shorted to the Ground and when
the FB point voltage decreases less than half of the reference voltage (Vref) and a current more than the ILIM flows to
the driver transistor, the short-circuit protection quickly operates to turn off and to latch the driver transistor. In latch
mode, the operation can be resumed by either turning the IC off and on via the CE/MODE pin, or by restoring power
supply to the VIN pin.
When sharp load transient happens, a voltage drop at the VOUT is propagated to the FB point through CFB, as a result,
short circuit protection may operate in the voltage higher than 1/2 VOUT voltage.
<U.V.L.O. Circuit>
When the VIN pin voltage becomes 1.4V or lower, the P-channel output driver transistor is forced OFF to prevent false
pulse output caused by unstable operation of the internal circuitry. When the VIN pin voltage becomes 1.8V or higher,
switching operation takes place. By releasing the U.V.L.O. function, the IC performs the soft start function to initiate
output startup operation. The soft start function operates even when the VIN pin voltage falls momentarily below the
U.V.L.O. operating voltage. The U.V.L.O. circuit does not cause a complete shutdown of the IC, but causes pulse output
to be suspended; therefore, the internal circuitry remains in operation.
<PFM Switch Current>
In PFM control operation, until coil current reaches to a specified level (IPFM), the IC keeps the P-ch MOSFET on. In this
case, time that the P-ch MOSFET is kept on (TON) can be given by the following formula.
TON= L×IPFM (VIN-VOUT)
→IPFM①
<Maximum IPFM Limit>
In PFM control operation, the maximum duty ratio (MAXIPFM) is set to 200% (TYP.). Therefore, under the condition that
the duty increases (e.g. the condition that the step-down ratio is small), it’s possible for P-ch MOSFET to be turned off even
when coil current doesn’t reach to IPFM.
→IPFM②
IPFM②
IPFM①
Ton
FOSC
Maxumum IPFMCurrent
Lx
Lx
IPFM
0mA
IPFM
0mA
I Lx
I Lx
10/28
XC9235/XC9236/XC9237
Series
■OPERATIONAL DESCRIPTION (Continued)
<CL High Speed Discharge>
XC9235B(C)/ XC9236B(C)/ XC9237B(C) series can quickly discharge the electric charge at the output capacitor (CL) when
a low signal to the CE pin which enables a whole IC circuit put into OFF state, is inputted via the N-channel transistor
located between the LX pin and the VSS pin. When the IC is disabled, electric charge at the output capacitor (CL) is quickly
discharged so that it may avoid application malfunction. Discharge time of the output capacitor (CL) is set by the CL
auto-discharge resistance (R) and the output capacitor (CL). By setting time constant of a CL auto-discharge resistance
value [R] and an output capacitor value (CL) as τ(τ=C x R), discharge time of the output voltage after discharge via the N
channel transistor is calculated by the following formulas.
V = VOUT(E) x e –t/τ, or t=τln (VOUT(E) / V)
V : Output voltage after discharge
VOUT(E) : Output voltage
t: Discharge time,
τ: C x R
C= Capacitance of Output capacitor (CL)
R= CL auto-discharge resistance
Output Voltage Dischage Characteristics
Rdischg = 300Ω(TYP)
100
90
80
70
60
50
40
30
20
10
CL=10uF
CL=20uF
CL=50uF
0
0
10
20
30
40
50
60
70
80
90 100
Discharge Time t (ms)
11/28
XC9235/XC9236/XC9237 Series
■OPERATIONAL DESCRIPTION (Continued)
<CE/MODE Pin Function>
The operation of the XC9235/XC9236/XC9237 series will enter into the shut down mode when a low level signal is input to the
CE/MODE pin. During the shutdown mode, the current consumption of the IC becomes 0μA (TYP.), with a state of high
impedance at the Lx pin and VOUT pin. The IC starts its operation by inputting a high level signal to the CE/MODE pin. The
input to the CE/MODE pin is a CMOS input and the sink current is 0μA (TYP.).
●XC9235/XC9236 series - Examples of how to use CE/MODE pin
(A)
SW_CE
ON
STATUS
Stand-by
Operation
OFF
(B)
SW_CE
ON
STATUS
Operation
Stand-by
OFF
(B)
(A)
●XC9237 series - Examples of how to use CE/MODE pin
(A)
SW_CE
ON
SW_PWM/PFM
STATUS
PWM/PFM Automatic Switching Control
PWM Control
*
OFF
ON
OFF
OFF
Stand-by
(B)
SW_CE
ON
SW_PWM/PFM
STATUS
Stand-by
*
(B)
(A)
OFF
ON
OFF
PWM Control
OFF
PWM/PFM Automatic Switching Control
Intermediate voltage can be generated by RM1 and RM2. Please set the value of each R1, R2, RM1, RM2 from
few hundreds kΩ to few hundreds MΩ. For switches, CPU open-drain I/O port and transistor can be used.
12/28
XC9235/XC9236/XC9237
Series
■OPERATIONAL DESCRIPTION (Continued)
<Soft Start>
Soft start time is available in two options via product selection.
The XC9235A/XC9236A/XC9237A/XC9235C/XC9236C/XC9237C series provide 1.0ms (TYP). The XC9225B/XC9236B/XC9237B series
provide 0.25ms (TYP). Soft start time is defined as the time to reach 90% of the output setting voltage when the CE pin is turned on.
90% of setting voltage
■FUNCTION CHART
CE/MODE
OPERATIONAL STATES
VOLTAGE LEVEL
XC9235
XC9236
Synchronous
XC9237
Synchronous
Synchronous
H Level (*1)
M Level (*2)
L Level (*3)
PWM/PFM
PWM/PFM
PWM Fixed Control
Automatic Switching
Automatic Switching
Synchronous
━
━
PWM Fixed Control
Stand-by
Stand-by
Stand-by
Note on CE/MODE pin voltage level range
(*1) H level: 0.65V < H level < VIN V (for XC9235/XC9236)
H level: VIN – 0.25V < H level < VIN (for XC9237)
(*2) M level: 0.65V < M level < VIN - 1.0V (for XC9237)
(*3) L level: 0V < L level < 0.25V
13/28
XC9235/XC9236/XC9237 Series
■NOTE ON USE
1. The XC9235/XC9236/XC9237 series is designed for use with ceramic output capacitors. If, however, the potential
difference is too large between the input voltage and the output voltage, a ceramic capacitor may fail to absorb the resulting
high switching energy and oscillation could occur on the output. If the input-output potential difference is large, connect an
electrolytic capacitor in parallel to compensate for insufficient capacitance.
2. Spike noise and ripple voltage arise in a switching regulator as with a DC/DC converter. These are greatly influenced by
external component selection, such as the coil inductance, capacitance values, and board layout of external components.
Once the design has been completed, verification with actual components should be done.
3. Depending on the input-output voltage differential, or load current, some pulses may be skipped, and the ripple voltage may
increase.
4. When the difference between VIN and VOUT is large in PWM control, very narrow pulses will be outputted, and there is the
possibility that some cycles may be skipped completely.
5. When the difference between VIN and VOUT is small, and the load current is heavy, very wide pulses will be outputted and
there is the possibility that some cycles may be skipped completely.
6. With the IC, the peak current of the coil is controlled by the current limit circuit. Since the peak current increases when
dropout voltage or load current is high, current limit starts operation, and this can lead to instability. When peak current
becomes high, please adjust the coil inductance value and fully check the circuit operation. In addition, please calculate
the peak current according to the following formula:
Ipk = (VIN - VOUT) x OnDuty / (2 x L x FOSC) + IOUT
L: Coil Inductance Value
FOSC: Oscillation Frequency
7. When the peak current which exceeds limit current flows within the specified time, the built-in P-ch driver transistor turns off.
During the time until it detects limit current and before the built-in transistor can be turned off, the current for limit current
flows; therefore, care must be taken when selecting the rating for the external components such as a coil.
8. When VIN is less than 2.4V, limit current may not be reached because voltage falls caused by ON resistance.
9. Care must be taken when laying out the PC Board, in order to prevent misoperation of the current limit mode. Depending
on the state of the PC Board, latch time may become longer and latch operation may not work. In order to avoid the effect of
noise, the board should be laid out so that input capacitors are placed as close to the IC as possible.
10. Use of the IC at voltages below the recommended voltage range may lead to instability.
11. This IC should be used within the stated absolute maximum ratings in order to prevent damage to the device.
12. When the IC is used in high temperature, output voltage may increase up to input voltage level at no load because of the
leak current of the driver transistor.
13. The current limit is set to 1350mA (MAX.) at typical. However, the current of 1350mA or more may flow. In case that the
current limit functions while the VOUT pin is shorted to the GND pin, when P-ch MOSFET is ON, the potential difference for
input voltage will occur at both ends of a coil. For this, the time rate of coil current becomes large. By contrast, when
N-ch MOSFET is ON, there is almost no potential difference at both ends of the coil since the VOUT pin is shorted to the
GND pin. Consequently, the time rate of coil current becomes quite small. According to the repetition of this operation,
and the delay time of the circuit, coil current will be converged on a certain current value, exceeding the amount of current,
which is supposed to be limited originally. Even in this case, however, after the over current state continues for several
ms, the circuit will be latched. A coil should be used within the stated absolute maximum rating in order to prevent
damage to the device.
①Current flows into P-ch MOSFET to reach the current limit (ILIM).
②The current of ILIM or more flows since the delay time of the circuit occurs during from the detection of the current limit to
OFF of P-ch MOSFET.
③Because of no potential difference at both ends of the coil, the time rate of coil current becomes quite small.
④Lx oscillates very narrow pulses by the current limit for several ms.
⑤The circuit is latched, stopping its operation.
②
④
①
③
⑤
Limit >
#
ms
Delay
LX
ILIM
ILX
14/28
XC9235/XC9236/XC9237
Series
■NOTE ON USE (Continued)
14. In order to stabilize VIN’s voltage level and oscillation frequency, we recommend that a by-pass capacitor (CIN) be
connected as close as possible to the VIN & VSS pins.
15. High step-down ratio and very light load may lead an intermittent oscillation.
16. During PWM / PFM automatic switching mode, operating may become unstable at transition to continuous mode.
Please verify with actual parts.
17. Please note the inductance value of the coil. The IC may enter unstable operation if the combination of ambient
temperature, setting voltage, oscillation frequency, and L value are not adequate.
In the operation range close to the maximum duty cycle, The IC may happen to enter unstable output voltage operation
even if using the L values listed below.
●The Range of L Value
<External Components>
FOSC
VOUT
L Value
3.0MHz
0.8V<VOUT<4.0V
1.0μH~2.2μH
3.3μH~6.8μH
4.7μH~6.8μH
V
OUT≦2.5V
1.2MHz
2.5V<VOUT
*When
a coil less value of 4.7μH is used at
FOSC=1.2MHz or when a coil less value of 1.5μH is
used at FOSC=3.0MHz, peak coil current more easily
reach the current limit ILMI. In this case, it may
happen that the IC can not provide 600mA output
current.
18. It may happen to enter unstable operation when the IC operation mode goes into continuous operation mode under the
condition of small input-output voltage difference. Care must be taken with the actual design unit.
<External Components>
15/28
XC9235/XC9236/XC9237 Series
■NOTE ON USE (Continued)
●Instructions of pattern layouts
1. In order to stabilize VIN voltage level, we recommend that a by-pass capacitor (CIN) be connected as close as possible to
the VIN & VSS pins.
2. Please mount each external component as close to the IC as possible.
3. Wire external components as close to the IC as possible and use thick, short connecting traces to reduce the circuit
impedance.
4. Make sure that the PCB GND traces are as thick as possible, as variations in ground potential caused by high ground
currents at the time of switching may result in instability of the IC.
5. This series’ internal driver transistors bring on heat because of the output current and ON resistance of driver transistors.
16/28
XC9235/XC9236/XC9237
Series
■TEST CIRCUITS
Wave Form Measure Point
Circuit ②
Circuit ①
L
VIN
Lx
VIN
Lx
A
A
CE/
MODE
CE/
MODE
1μF
VOUT
VOUT
VSS
V
CIN
CL
VSS
※ꢀExternal Components
L
:
1.5μH(NR3015) 3.0MHz
4.7μH(NR4018) 1.2MHz
CIN : 4.7μF(ceramic)
CL :10μF(ceramic)
Circuit ④
Circuit ③
Wave Form Measure Point
VIN
Lx
VIN
Lx
CE/
MODE
CE/
MODE
Rpulldown
200Ω
1μF
100mA
VOUT
VOUT
V
1μF
VSS
VSS
ON resistance = (VIN-VLx)/100mA
Circuit ⑤
Circuit ⑥
>
ILeakH
Wave Form Measure Point
VIN
Lx
VIN
Lx
A
1μF
ICEH
ILeakL
CE/
MODE
CE/
MODE
1μF
ILIM
VOUT
VOUT
V
A
VSS
VSS
ICEL
Circuit ⑦
Circuit ⑧
ILx
Wave Form Measure Point
VIN
Lx
VIN
Lx
A
Ilat
CE/
MODE
CE/
MODE
1μF
VOUT
VOUT
VSS
1uF
VSS
Rpulldown
1Ω
Circuit ⑨
VIN
Lx
A
CE/
MODE
VOUT
CIN
VSS
17/28
XC9235/XC9236/XC9237 Series
■TYPICAL PERFORMANCE CHARACTERISTICS
(1) Efficiency vs. Output Current
XC9237A18C
XC9237A18D
L=4.7μH (NR4018), CIN=4.7μF, CL=10μF
L=1.5μH (NR3015), CIN=4.7μF, CL=10μF
WM/PFM Automatic Sw itchng ontol
PWM/PFM Automatc itching Control
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VIN= 4.2V
VIN= 4.2V
3.6V
PWM Control
VIN= 4.2V
3.6V
2.4V
3.6V
2.4V
PWM Control
VIN= 4.2V
2.4V
3.6V
2.4V
0.1
1
10
IO
100
1000
0.1
1
10
100
1000
O
ut
p
u
t
C
u
rr
e
n
t
:
U
T
(
m
A
)
Output Current: IOUT (mA)
(2) Output Voltage vs. Output Current
XC9237A18C
XC9237A18D
L=1.5μH (NR3015), CIN=4.7μF, CL=10μF
L=4.7μH (NR4018), CIN=4.7μF, CL=10μF
2.1
2.0
1.9
1.8
1.7
1.6
1.5
2.1
2.0
1.9
1.8
1.7
1.6
1.5
PWM/PFM Automatic Sw itching Control
PWM/PFM Automatic Sw itching Control
VIN 4.2V,3.6V,2.4V
=
VIN 4.2V,3.6V,2.4V
=
PWM Control
PWM Control
0.1
1
10
100
1000
0.1
1
10
100
1000
Output Current: IOUT (mA)
Output Current: IOUT (mA)
(3) Ripple Voltage vs. Output Current
XC9237A18C
XC9237A18D
L=1.5μH (NR3015), CIN=4.7μF, CL=10μF
L=4.7μH (NR4018), CIN=4.7μF, CL=10μF
100
80
60
40
20
0
100
80
60
40
20
0
PWM/PFM Automatic
PWM Control
PWM/PFM A utomatic
Sw itching Control
Sw itching Control
VIN 4.2V,3.6V,2.4V
=
VIN 4.2V
=
PWM Control
VIN 4.2V
=
3.6V
VIN 4.2V,3.6V,2.4V
=
3.6V
2.4V
ꢀꢀ
2.4V
ꢀꢀ
0.1
1
10
t:
100
1000
0.1
1
10
t:
IO
100
A)
1000
O
u
tp
u
t
C
ur
r
n
I
O
U
(m
A
)
O
u
tp
u
t
C
u
r
re
n
U
T
(
m
18/28
XC9235/XC9236/XC9237
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(4) Oscillation Frequency vs. Ambient Temperature
XC9237A18D
L=1.5μH (NR3015), CIN=4.7μF, CL=10μF
XC9237A18C
L=4.7μH (NR4018), CIN=4.7μF, CL=10μF
1.5
3.5
3.4
3.3
3.2
3.1
3.0
2.9
2.8
2.7
2.6
2.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
VIN=3.6V
VIN=3.6V
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature: Ta (℃)
Ambient Temperature: Ta (℃)
(5) Supply Current vs. Ambient Temperature
XC9237A18D
XC9237A18C
40
40
VIN=6.0V
35
30
35
30
25
20
15
10
5
VIN=4.0V
VIN=6.0V
VIN=2.0V
25
20
15
10
5
VIN=4.0V
VIN=2.0V
0
0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature: Ta (℃)
Ambient Temperature: Ta (℃)
(6) Output Voltage vs. Ambient Temperature
(7) UVLO Voltage vs. Ambient Temperature
XC9237A18D
XC9237A18D
2.1
1.8
CE=VIN
2.0
1.5
1.2
0.9
0.6
0.3
0.0
1.9
VIN=3.6V
1.8
1.7
1.6
1.5
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature: Ta (℃)
Ambient Temperature: Ta (℃)
19/28
XC9235/XC9236/XC9237 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) CE "H" Voltage vs. Ambient Temperature
(9) CE "L" Voltage vs. Ambient Temperature
XC9237A18D
XC9237A18D
1.0
1.0
0.9
0.8
0.9
0.8
VIN=5.0V
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.7
VIN=5.0V
0.6
0.5
0.4
VIN=3.6V
0.3
0.2
0.1
0.0
VIN=3.6V
VIN=2.4V
VIN=2.4V
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature: Ta (℃)
Ambient Temperature: Ta (℃)
(10) Soft Start Time vs. Ambient Temperature
XC9237A18C
XC9237A18D
L=4.7μH (NR4018), CIN=4.7μF, CL=10μF
L=1.5μH (NR3015), CIN=4.7μF, CL=10μF
5
4
3
2
1
0
5
4
3
2
1
0
VIN=3.6V
VIN=3.6V
-50
-25
0
25
Ambient Temperature: Ta (℃)
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature: Ta (℃)
(11) "Pch / Nch" Driver on Resistance vs. Input Voltage
XC9237A18D
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Nch on Resistance
Pch on Resistance
0
1
2
3
4
5
6
Input Voltage: VIN (V)
20/28
XC9235/XC9236/XC9237
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(12) XC9235B/36B/37B Rise Wave Form
XC9237B12C
XC9237B33D
L=4.7μH (NR4018), CIN=4.7μF, CL=10μF
L=1.5μH (NR3015), CIN=4.7μF, CL=10μF
VIN=5.0V
VIN=5.0V
IOUT=1.0mA
IOUT=1.0mA
VOUT:1.0V/div
VOUT:0.5V/div
CE:0.0V⇒1.0V
100μs/div
CE:0.0V⇒1.0V
100μs/div
(13) XC9235B/36B/37B
Soft-Start Time vs. Ambient Temperature
XC9237B12C
XC9237B33D
L=4.7μH(NR4018), CIN=4.7μF, CL=10μF
L=1.5μH(NR3015), CIN=4.7μF, CL=10μF
500
400
300
200
100
0
500
400
300
200
100
0
VIN=5.0V
IOUT=1.0mA
VIN=5.0V
IOUT=1.0mA
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature: Ta(℃)
Ambient Temperature: Ta(℃)
(14) XC9235B/36B/37B
CL Discharge Resistance vs. Ambient Temperature
XC9237B33D
600
500
400
300
200
100
VIN=6.0V
VIN=4.0V
VIN=2.0V
-50
-25
0
25
50
75
100
Ambient Temperature: Ta (
)
℃
21/28
XC9235/XC9236/XC9237 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(15) Load Transient Response
XC9237A18C
L=4.7μH (NR4018), CIN=4.7μF (ceramic), CL=10μF (ceramic), Topr=25℃
VIN=3.6V, VCE=VIN (PWM/PFM Automatic Switching Control)
IOUT=1mA → 100mA
IOUT=1mA → 300mA
1ch: IOUT
1ch: IOUT
2ch
2ch
VOUT: 50mV/div
VOUT: 50mV/div
50μs/div
50μs/div
I
OUT=100mA → 1mA
IOUT=300mA → 1mA
1ch: IOUT
1ch: IOUT
2ch
2ch
V
OUT: 50mV/div
VOUT: 50mV/div
200μs/div
200μs/div
22/28
XC9235/XC9236/XC9237
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(15) Load Transient Response (Continued)
XC9237A18C
L=4.7μH (NR4018), CIN=4.7μF (ceramic), CL=10μF (ceramic), Topr=25℃
VIN=3.6V, VCE=1.8V (PWM Control)
IOUT=1mA → 100mA
IOUT=1mA → 300mA
1ch: IOUT
1ch: IOUT
2ch
2ch
VOUT: 50mV/div
VOUT: 50mV/div
50μs/div
50μs/div
I
OUT=100mA → 1mA
IOUT=300mA → 1mA
1ch: IOUT
1ch: IOUT
2ch
2ch
V
OUT: 50mV/div
VOUT: 50mV/div
200μs/div
200μs/div
23/28
XC9235/XC9236/XC9237 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(15) Load Transient Response (Continued)
XC9237A18D
L=1.5μH (NR3015), CIN=4.7μF (ceramic), CL=10μF (ceramic), Topr=25℃
VIN=3.6V, VCE=VIN (PWM/PFM Automatic Switching Control)
IOUT=1mA → 100mA
IOUT=1mA → 300mA
1ch: IOUT
1ch: IOUT
2ch
2ch
VOUT: 50mV/div
VOUT: 50mV/div
50μs/div
50μs/div
I
OUT=100mA → 1mA
IOUT=300mA → 1mA
1ch: IOUT
1ch: IOUT
2ch
2ch
VOUT: 50mV/div
VOUT: 50mV/div
200μs/div
200μs/div
24/28
XC9235/XC9236/XC9237
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(15) Load Transient Response (Continued)
XC9237A18D
L=1.5μH (NR3015), CIN=4.7μF (ceramic), CL=10μF (ceramic), Topr=25℃
VIN=3.6V, VCE=1.8V (PWM Control)
IOUT=1mA → 100mA
IOUT=1mA → 300mA
1ch: IOUT
1ch: IOUT
2ch
2ch
VOUT: 50mV/div
VOUT: 50mV/div
50μs/div
50μs/div
I
OUT=100mA → 1mA
IOUT=300mA → 1mA
1ch: IOUT
1ch: IOUT
2ch
2ch
VOUT: 50mV/div
VOUT: 50mV/div
200μs/div
200μs/div
25/28
XC9235/XC9236/XC9237 Series
■PACKAGING INFORMATION
●SOT-25
●USP-6C
●USP-6C Recommended Pattern Layout
●USP-6C Recommended Metal Mask Design
26/28
XC9235/XC9236/XC9237
Series
■MARKING RULE
●SOT-25 & USP-6C
①Represent product series
MARK
PRODUCT SERIES
4
5
XC9235A
XC9236A
XC9237A
XC9235B
XC9236B
XC9237B
XC9235C
XC9236C
XC9237C
6
C
D
E
K
L
M
SOT-25
②Represents integer number of output voltage and oscillation frequency
(TOP VIEW)
OUTPUT
MARK
VOLTAGE (V)
FOSC =1.2MHz
FOSC =3.0MHz
0.X
1.X
2.X
3.X
4.X
A
B
C
D
E
F
H
K
L
M
③Represents decimal point of output voltage
OUTPUT
MARK
OUTPUT
MARK
VOLTAGE (V)
X.00
VOLTAGE (V)
X.05
USP-6C
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(TOP VIEW)
X.10
X.15
X.20
X.25
X.30
X.35
X.40
X.45
X.50
X.55
X.60
X.65
H
K
L
X.70
X.75
X.80
X.85
X.90
X.95
M
④⑤Represents production lot number
Order of 01, …09, 10, 11, …99, 0A, …0Z, 1A, …9Z, A0, …Z9, AA, …ZZ.
(G, I, J, O, Q, W excepted)
*No character inversion used.
27/28
XC9235/XC9236/XC9237 Series
1. The products and product specifications contained herein are subject to change without
notice to improve performance characteristics. Consult us, or our representatives
before use, to confirm that the information in this catalog is up to date.
2. We assume no responsibility for any infringement of patents, patent rights, or other
rights arising from the use of any information and circuitry in this catalog.
3. Please ensure suitable shipping controls (including fail-safe designs and aging
protection) are in force for equipment employing products listed in this catalog.
4. The products in this catalog are not developed, designed, or approved for use with such
equipment whose failure of malfunction can be reasonably expected to directly
endanger the life of, or cause significant injury to, the user.
(e.g. Atomic energy; aerospace; transport; combustion and associated safety
equipment thereof.)
5. Please use the products listed in this catalog within the specified ranges.
Should you wish to use the products under conditions exceeding the specifications,
please consult us or our representatives.
6. We assume no responsibility for damage or loss due to abnormal use.
7. All rights reserved. No part of this catalog may be copied or reproduced without the
prior permission of Torex Semiconductor Ltd.
28/28
XC9237A0BCMR 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
XC9237A0BDEL | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0BDER | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0BDML | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0BDMR | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0CCEL | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0CCER | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0CCML | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0CCMR | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0CDEL | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 | |
XC9237A0CDER | TOREX | 600mA Driver Tr. Built-In, Synchronous Step-Down DC/DC Converters | 获取价格 |
XC9237A0BCMR 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6