TB1254N_技术文档

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TENTATIVE TOSHIBA Bi-CMOS INTEGRATED CIRCUIT, SILICON MONOLITHIC

TB1254N

PAL / NTSC / SECAM 1CHIP (IF+VCD PROCESSOR) IC

The TB1254N is a TV signal processor IC, which contains

PIF, SIF, Video, Chroma and deflection signal processors

for worldwide Multi-color systems. Also, it has AV switch

for TV/EXT inputs.

The line-up and flexibility of this TB1251 series contributes

to reduce development costs and components in a TV

sets.

SDIP56-P-600

Weight: 5.55g (typ)

FEATURES

IF STAGE

Multi-system IF

TEXT STAGE

SIF 4.5 ~ 6.5 MHz

One External BPF for Multi-SIF carrier

Inter carrier inputs

VCO tank coil alignment free

for L system,

Built-in AKB

AKB on/off

AKB Color temperature control

Analog RGB interfaces

ABL / ACL

Positive demodulation

V low Ch

DEFLECTION STAGE

Built-in H-VCO

ramp distortion correction

Stand Along Sync in port

Sand Castle Pulse Output

(HD+VD+Gate Pulse)

VIDEO STAGE

Built-in Y delay line (8 adjustable steps)

Built in C trap filter (Switchable)

CHROMA STAGE

AV SWITCH

Multi-color Demoduration

Automatic Chroma Identification

1 Xtal for Multi-color Systems

(3.58MHz/4.43MHz/M-PAL/N-PAL)

Built-in1H Delay line

Visual TV / EXT inputs

Audio TV / EXT inputs

Cb/Cr input ports

Built-in BPF / TOF

Fsc Output

Two NTSC demodulation phase

TOSHIBA is continually working to improve the quality and the reliability of its products. Nevertheless,

semiconductor devices in general can malfunction or jail due to their inherent electrical sensitivity and

vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to

observe standards of safety, and to avoid situations in which a malfunction or failure of a TOSHIBA product could

cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that

TOSHIBA products are used within specified operating range as set forth in the most recent products specifications.

Also, please keep in mind the precautions and conditions set forth in the TOSHIBA Semiconductor Reliability

Handbook.

The products described in this document are subject to foreign exchange and foreign trade control laws.

The information contained herein is presented only as a guide for the applications of our products. No

responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of

00/01/28 1

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

H.AFC

ABCL IN

ref R

+

FBP IN/SCP OUT

H Vcc(9V)

V OUT

V NFB

+

H OUT

V RAMP

Dig GND

SCL

IK IN

B OUT

G OUT

R OUT

SDA

BLACK Det

+

Dig.VDD

+

Sync in

YC GND

Y

IN

EXT.B IN

DC Restor

EXT.G IN

EXT.R IN

Ys/Ym

MONITOR OUT

YC Vcc(5V)

+

RGB Vcc(9V)

+

C in

CW OUT

Cr in

4.43MHz X'tal

Cb in

EXT IN

APC Filter

+

LOOP Filter

IF AGC

+

TV in

RF AGC

+

DE-EMP.

N.C.

DC NF

+

IF GND

AUDIO OUT

EXT AUDIO IN

IF DET OUT

AFT OUT

SIF OUT

Ripple F

Hcorr IN/SIF IN

IF Vcc(5V)

+

00/01/28 2

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TERMINAL INTERFACE

PIN NAME

FUNCTION

INTERFACE

1

2

IF VCC

A Vcc terminal for the IF circuit.

Supply 5V.

•

RIPPLE

FILTER

A terminal to be leaded to an internal bias

filter. Put a capacitor.

1

1kƒ¶

2kƒ¶

330ƒ¶

2

330ƒ¶

27.5kƒ¶

45kƒ¶

5

3

SIF OUT

An output terminal for a 1st SIF signal, that

beaten down by a regenerated carrier.

The SIF frequencies are able to convert into

only 6.5MHz, in order to eliminate SIF BPFs

to single 6.5MHz.

9V

14

100ƒ¶

500ƒ¶

15kƒ¶

3

16kƒ¶

16.3kƒ¶

5

4

AUDIO OUT

An output terminal for audio signal.

FM Det.signal or the external audio signal,

input to pin53, is output (Switched by bus).

An internal audio attenator controles the

output levelS. •

9V

14

100ƒ¶

ATT

4

50kƒ¶

5.3V

30kƒ¶

5

IF GND

The GND terminal for IF circuit.

•

6

7

IF IN

Input terminals for IF signals. Pin 6 and 7 are

the both input poles of a differential amplifier.

The norminal input level is 90dB(•V)(Pin6-7),

input impedance is 1.5 k ohms.

1

5

100kƒ¶

6

7

1.44kƒ¶

2.75V

1.5V

8

NC

-

00/01/28 3

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

RF AGC

FUNCTION

INTERFACE

9V

9

An output terminal for RF AGC.

14

A pull up resister is required because of its

open collector output, and also connect de-

coupling capacitor to reduce noises,.

300ƒ¶

9

30kƒ¶

to SELF ADJ

30kƒ¶

5

1

10 IF AGC

A terminal to be connected to an IF AGC

filter. Connect 2.2•F of capacitor to Vcc

10

2kƒ¶

5

11 APC FILTER

A terminal to be connected with an APC filter

for chroma demodulation.

42

This terminal voltage controls the frequency

of VCXO.

110kƒ¶

11

220ƒ¶

3.2V

19

12 X’TAL

(4.43MHZ)

A

terminal to be connected with

a

42

19

4.433619MHz X’tal oscillator. The oscillated

signal lead to chroma demodulation, H out

frequency tuning, AFT and so on.

12

500ƒ ¶

2.5kƒ ¶

13 CW OUT

An output terminal for the continuous chroma

sub-carrier frequency wave, which amplitude

is 0.7Vp-p (typ).

42

1kƒ¶

Also the dc level shows killer status, the level

is 1.5V for B/W and 3.5V for Color.

13

200ƒ¶

19

00/01/28 4

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

FUNCTION

INTERFACE

14 RGB VCC (9V) A Vcc terminal for RGB block, PIF det. Output

and sound output circuit.

Supply 9V.

•

15 YS/YM SW

A terminal for switching of EXT RGB Mode

and fast Half tone.

42

•Spot killer

15

250ƒ¶

3.3V

0.7V

14

42

16 EXT. R IN

17 EXT. G IN

18 EXT. B IN

Input terminals for EXT RGB signals. The

signals are clamped by capacitors, therefore

the input impedance should be low, 100

ohms or less is recommended.

For this input, brightness and RGB contrast

are available, also ABL/ACL eliminate the

output leval. This ABL/ACL is able to off.

OFF: for small area like OSD

ON: for large area like TELETEXT

(input level 0.7Vp-p/100IRE)

250ƒ¶

16

250ƒ¶

17

18

250ƒ¶

2.3V

100uA

19

14

19 Y/C GND

The GND terminal for Y/C circuit.

•

20 R OUT

21 G OUT

22 B OUT

Terminals for R/G/B signal output.

Connect resistances to GND, if through rate

is not enough. Because of source current

limitation, the resistances should be 2.0k•or

more.

20

100ƒ¶

21

22

19

42

23 IK IN

An input terminal to sense AKB cathode

current.

VK

Connect this terminals to GND if not using

the AKB system.

1kƒ¶

23

VF

soft

start

19

limitter

over circuit

00/01/28 5

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

24 V RAMP

FUNCTION

INTERFACE

A terminal to be connected with a capacitor to

generate the V.Ramp signal.

31

The V.Ramp amplitude is kept constant by

the V.AGC.

200ƒ¶

24

V

AGC

33

25 V NFB

An input terminal for V saw-teeth signal

feedback.

31

If the DC voltage on this pin is less than 1.7V,

it blanks RGB output for V guard.

25

2V

12.5kƒ¶

33

31

V

GUARD

26 V OUT

An output terminal for the vertical driving

pulses.

30kƒ¶

200ƒ¶

26

1kƒ¶

0.5V

33

V

OUT read

27 REF. R

A terminal to be connected with resistance to

stabilize internal current sources.

31

Connect 5.6 k

1% of resistance to GND.

6.8k

27

49k

33

00/01/28 6

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

28 ABCL IN

FUNCTION

INTERFACE

An input terminal for ABL/ACL control.

Control voltage range is 5.5•6.0V.

The ratio of ABL against ACL can be set by

bus control.

29 H AFC FILTER A terminal to be connected with H. AFC Filter.

The DC voltage of this pin controls the H

VCO frequency.

31

237ƒ¶

29

100kƒ¶

33

31

30 FBP IN/ SCP An input terminal for FBP.

OUT

The V and GP Pulses are overlaid as SCP.

3VF

VD

3.5V

30

1.4V

GP

33

protect

GP

VD

H AFC

H BLK

31 H VCC (9V)

32 H OUT

A Vcc terminal for DEF circuit, HOUT,

IICBUS POR etc.

Supply 9V.

•

An output terminal for horizontal driving

pulses.

31

50ƒ¶

32

2VF

6kƒ¶

33

33 DIG GND

A GND terminal for digital block.

•

00/01/28 7

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

FUNCTION

INTERFACE

34 SCL

An input terminal for IICBUS clock.

31

3.25V

34

5kƒ¶

33

31

35 SDA

An input/output terminal for IICBUS data.

3.25V

35

5kƒ¶

33

42

36 BLACK DET

A terminal to be connected with Black det.

filter for black stretch.

This terminal voltage controls Black

stretching gain.

The IIC Bus controls on/off and start point of

Black stretch.

4kƒ¶

36

2.5V

19

37 DIG. VDD

A Vdd terminal for of digital block.

Supply HVcc voltage through 270 ohms of

resistance.

The voltage of this terminal is clipped in

about 3.3V by the internal regulator.

H VCC

31

37

VDD

30ƒ¶

2.6V

750ƒ¶

00/01/28 8

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

FUNCTION

INTERFACE

38 SYNC IN

An input terminal for Sync signal.

31

The input sync chip is clamped by

charging/discharging the coupling capacitors

so as to align the Sync slice level, therefore

input through low impedance buffer.

(input level 1Vp-p/140IRE)

832ƒ¶

38

3VF

1kƒ¶

6kƒ¶

24kƒ¶

33

42

39 Y IN

An input terminal for Y signal.

The pedestal level is clamped by means of

charging/discharging the coupling capacitor,

therefore input through low impedance buffer.

(1Vp-p/140IRE input level)

39

1kƒ¶

19

<Amp>

40 DC RESTOR

A terminal to be connected with a capacitor to

detect the average picture level for DC

restoration.

42

The ratio of the DC restoration is set by bus.

Leave this terminal open if the DC restoration

is not required.

50k

40

10k

19

41 MON OUT

An output terminal of AV SW monitor.

The input signal for pin # 46/48 is output

through 6dB amplifier .

14

19

(output level 2Vp-p/140IRE)

41

8kƒ¶

2V

42 Y/C VCC

An Vcc terminal for Y/C circuit.

Supply 5V.

•

00/01/28 9

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

FUNCTION

INTERFACE

43 C-IN

An input terminal for chroma signal.

(standard burst amplitude level 286mVp-p•

The low/High impedance status of this pin

can be read by bus to detect if S port is

connected or not.

42

43

1kƒ¶

75kƒ¶

2.25V

19

42

44 Cr IN

45 Cb IN

Input terminals for Cb/Cr signals.

This terminal is clamped by charging /

discharging the coupling capacitors, therefore

input with low impedance, 100•or less are

recommended.

44

45

2.5V

B.B.TINT•-/+12deg•Sub color control are

available for Cb/Cr input signals.

19

14

clamp

46 EXT IN

An input terminal for external video signal.

(input level 1Vp-p / 140 IRE)

1kƒ¶

2V

46

1kƒ¶

19

5V

47 LOOP FILTER

A terminal to be connected with loop filter for

PIF PLL.

1

The terminal voltage is controlled PIF VCO

frequency.

1kƒ¶

500ƒ¶

15kƒ¶

47

5

00/01/28 10

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

FUNCTION

INTERFACE

48 TV IN

An input terminal for TV video signal.

(input level 1Vp-p / 140 IRE)

14

1kƒ¶

2V

48

1kƒ¶

19

14

49 De-Emphasis

A terminal to De-Emphasis Audio signal, and

pick up detected Audio signal. Connect

capacitor (0.01•F to GND.

•Mon-OUT

The time constant 50/75us is set by the

IICBUS control “SIF Freq”.

Remove the capacitor in case of use US/JPN

sound multiplex system.

49

15kƒ¶ 7.5kƒ¶ 500ƒ¶

5

50 PIF TANK

51

Terminals to connect a PIF tank coil.

The tank coil should be pre-set up within +/-

2% for the automatic tuning. Manual tuning is

also available..

The resonance capacitance of the tank

should be 18pF.

1

50

51

5

52 DC NF

A terminal for connect the capacitor for DC

NF.

14

52

2kƒ¶ 10kƒ¶

5

00/01/28 11

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

PIN NAME

FUNCTION

INTERFACE

53 EXT AUDIO IN An input terminal for external audio signal.

Nominal input level is 500mVrms.

14

53

35k

4.5V

19

14

54 IF DET OUT

An output terminal of detected PIF.

(typical output level 2.2Vp-p)

200ƒ¶

54

1kƒ¶

5

55 AFT OUT

An output terminal for AFT.

1

output dc range;

0•2.5•5V.

100kƒ¶

output impedance; 50 k ohms (typ.)

55

100ƒ¶

100kƒ¶

5

SELF TEST

OUT

AFT OUT

AFT READ

56 SIF in / H corr.

An input terminal for 2’nd SIF signal and

H.curve correction.

1

H

corr

500 7pF

56

20kƒ¶

2.5V

SIF

5

00/01/28 12

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

BUS CONTROL MAP for TB1254N

Write Mode

Slave Address: 88 HEX

Sub

Addr.

00

D7

MSB

WPS

B.B.

D6

D5

D4

D3

D2

D1

D0

LSB

PRESET

Uni-Color

0000 0000

0100 0000

0010 0000

0110 0000

0011 0000

0001 0000

0100 0000

1000 1000

0000 0000

01

Brightness ( TV / Text )

Color

02

C-Trap

03

N Phase

Sharpness

04

Y MUTE

RGB Mt

Y D.L.

RGB Contrast

05

Sub Color

B.B.Tint

06

Video SW

N-Comb

Au SW

07

TINT

08

SECAM R-Y Black Adjust

S- GP Phase S-ID Sens

/ S- inhibit

SECAM B-Y Black Adjust

S-Black L-SECAM L-S AGC

09

Bell fo

S-ID

Mode

Monitor

SIF Freq.

Mode

Speed-up

0A

0B

PIF Freq

Color System

0000 0000

6.5MHz

SIF Fix

Audio Att

0C

0D

BPF/TOF

P/N-

ID Sens

Over Mod

SW

F ID

Coring

off

SIF

PIF VCO PIF VCO PIF VCO 0000 0000

Center

STD by Mode

5.74MHz Adj. Stop Adj. Req

Sprit/•nt•

Q Det

Gain

AFT Sens Au Gain AFT Mute

0000 0000

•

0E

0F

Self Test

RF AGC

0000 0000

Ysm M

RGB

DC Restoration

Black Stretch

Point

ABCL

10

11

ABL Start Point

ABL Gain

AKB System

Sub Contrast

Buzz

reducer

0000 1000

0001 1000

color -

12

13

14

15

16

17

R Cut Off

G Cut Off

B Cut Off

0000 0000

0100 0000

0000 0000

Cb/Cr SW

G Drive Gain

B Drive Gain

BLK

H-Stop

V-Stop

V AGC

V Ramp

Ref.

V-Freq.

312/313

Mode

18

19

1A

1B

1C

1D

1E

1F

Vertical Position

Horizontal Position

V S Correction

0001 0000

1000 1000

0010 0000

1000 0100

0100 0100

0000 0000

V Linaerity

AFC G

test(0)

Vertical Size

Horizontal Size

test(0)

*

EW Parabola correction

EW Trapezium Correction

EW Corner Correction

V. EHT

H. EHT

VSM SW

Test Mode

READ Mode

7

6

5

4

3

2

1

0

R0

R1

POR

Y-IN

IF Lock

RGB

OUT

H Lock

H-OUT

IF Level

V-OUT

V Freq

PIF VCO

Adj.

Color System

V Lock

AFT

R2

R3

Coil error PIF- VCO

error det

SYNC

DET

C IN DC

Product Code

S ID

AKB

CRT

AKB

STD/Non

-STD

P ID

N-ID

noise

det

Overflow Warm up

finish

00/01/28 13

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

IIC BUS CONROL FUNCTION

WRITE MODE

PIF STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

00000

RF AGC

6

RF AGC delay point (Pin6-7)

••Sub; 0E h

01: 65 dB(•V)

3F: 100 dB(•V)

:Mute

00: IF MUTE Stops Demodulation

IF Freq.

3

Setting IF frequency for digital AFT count down

000

••Sub; 0A h

000: 58.75 MHz

010: 39.5 MHz

100: 38.0 MHz

110: 33.95 MHz

AFT Mute Switch

0: normal

001: 45.75 MHz

011: 38.9 MHz

101: 34.47 MHz

111: 34.2 MHz

:58.75MHz

AFT Mute

••Sub; 0D h

AFT sens.

••Sub; 0D h

Over mod SW

••Sub; 0D h

Q det. Gain

••Sub; 0D h

L-SECAM Mode

••Sub; 09 h

1

0:normal

0:100kHz

0:off

1: AFT defeat (mute)

1: 25kHz/V

AFT sensitivity

0: 100kHz/v

on/off the over modulation switch

0: off

1: on

Q detector gain

0: high

0:high

1: low

1

L SECAM

0: Not L-SECAM

1: L-SECAM

0:Not

L-SECAM

turn the polarity for TV Det Out •for positive modulation•

Delay the AGC time constant (Peek AGC)

SIF AM demodulation

L-SECAM

Speed

••Sub; 09 h

VCO Center

••Sub; 0C h

AGC

1

Speed up the AGC sense for channel serch

0: normal

1: speed-up •Ch Serch•

0:normal

0: normal

VCO center SW

0: normal

1: Center

In adjusting a tank coil, set this bit to 1.

VCO adjust trigger

VCO Adj. Request

••Sub; 0C h

0: normal

1: VCO adjust trigger

The PIF VCO starts adjusting after requested.

While adjusting, the picture is blanked

Stop the readjustment on detecting the loosing adjustment

VCO Adj. Stop

1

0: normal

••Sub; 0C h

0: normal

1: stop self adjustment

“VCO Adj request” prier it

SIF STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

SIF Freq.

2

SIF Frequency

00:5.5MHz

••Sub; 0A h

00: 5.5MHz

10: 6.5MHz

01: 6.0MHz

11: 4.5MHz

Set the SIF frequency for;

Select the SIF FM demodulator band

select the de-emphasis speed

Set the ref.freq. for single •••MHz beet up if using

SIF 574

1

Set the SIF freq. to 5.74MHz for IGR Bilingual.

0:other

••Sub; 0C h

It sets the reference freq. for beet up the 5.74MHz to 6.5MHz.

frequencies

0: other frequencies

1: 5.74MHz

00/01/28 14

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

ITEMS

BITS DESCRIPTIONS

PRESET

Audio ATT

••Sub; 0B h

Au Gain

7

Audio attenuator

00: Mute

01: -85 dB ~ 7F: 0 dB

1

Audio Gain Switch

0:

0: 927mVrms at 25kHz/DEV

1: 500mVrms at 25kHz/DEV

927mVrms

at

••Sub; 0D h

25kHz/DEV

6.5MHz SIF Fix

••Sub; 0A h

Buzz Reducer

••Sub; 11 h

1

Beet up the SIF carrier frequency to 6.5MHz (single carrier)

0: normal

0: on

0: normal

1: beet up to uni- 6.5MHz

Nyquist Buzz Reducer SW

0: on

1: off

VIDEO STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

Sharpness

••Sub; 03 h

DC Rest.

6

Sharpness control

00: -5.4dB ~ 20: 3.3dB ~ 3F: 6.6 dB

DC Restoration control

00: 120%

10: 100%

peak:2.75MHz

00:-5.4dB

2

00:120%

00: off

••Sub; 0F h

01: 90%

11: 110%

Black Stretch

••Sub; 0F h

2

3

Set the black stretch start point

00: off

10: 35IRE

01: 25IRE

11: 45IRE

•point

••Sub; 0F h

Set the non linear curve for Y signal

00: off

10: 80IRE

00: off

01: 90IRE

11: 70IRE

Y DL

••Sub; 05 h

Y Delay time

000: -40ns

001: 0ns

010: +40ns

011: +80ns

Chroma trap filter for Y input

001: 0ns

100: +120ns

101: +160ns

110: +200ns

111: +240ns

C-Trap

1

0:OFF

••Sub; 02 h

0: OFF for Y / C Separated input

1: ON for internal C trap(-20dB or less)

WPS

1

White Peak Suppresser Switch

0: ON

0:ON

0: on

••Sub; 00 h

coring SW

••Sub; 0Ch

1: OFF

1: off

on/off the coring

0: on

00/01/28 15

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

CHROMA STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

TINT

7

Tint control for NTSC (CW TINT)

00:0deg

••Sub; 07 h

Color System

••Sub; 0A h

00: -33 deg

~ 7F: 33 deg

3

Color system switch

000: Auto 1 443PAL , 358NTSC , SECAM , 443NTSC

001: Auto 2 358NTSC , M-PAL , N-PAL (for S-America)

000: Auto 1

010: Fixed 358NTSC

100: Fixed 443PAL

011: Fixed 443NTSC

101: Fixed SECAM

110: Fixed M PAL 111: Fixed N PAL

N-Comb

••Sub; 07 h

1

2

Comb filter for base-band color signal of NTSC

0: ON

0:

set the relative phase / amplitude

00: NTSC1 (90 deg) 01: NTSC2 (105 deg)

ON

1:

OFF

00:NTSC1

(90 deg)

NTSC Phase

••Sub; 03 h

10/11: DVD (90 deg, 245 deg) for U/V inputs

Select chroma BPF frequency responce

0: BPF for EXT input 1: TOF for RF input

PAL / NTSC ID sensitivity for digital comb filter

BPF/TOF

••Sub; 0C h

1

0:BPF

0:Normal

P/N ID Sens

••Sub; 0C h.

F ID

0: Normal

1: Low

1

Forced killer off

0: normal

systems

0:normal

••Sub; 0E h

1: always color on in a fixed color

(This function dose not work in Auto 1 and Auto 2 mode)

SECAM STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

SECAM GP Phase

/ SECAM inhibit

2

4

SECAM ID phase / SECAM inhibit

00:+200ns

00: +200ns

01: normal

10: -200ns

11: SECAM inhibit

S Black Adj. R-Y

••Sub; 08 h

SECAM Black level adjust

1000: 0 mV

1000: 0mV

0:

-92 mV

14mV/dev

~ F:

+85mV

S Black Adj. B-Y

••Sub; 08 h

SECAM Black level adjust

0:

-92 mV

14mV/dev

Bell fo

1

SECAM Bell filter fo shift

0: 0 kHz

SECAM ID Sensitivity

0: normal

SECAM ID mode

0:

0:0 kHz

0:normal

0:H

••Sub; 09 h

S ID sense

••Sub; 09 h

S ID mode

••Sub; 09 h

S Black monitor

••Sub; 09 h

1:

+35 kHz

Low

H

H+V

SECAM Black level alignment mode

0: normal 1:

0:normal

Alignment

TEXT STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

0000000

:0dB

Uni-Color

7

Uni-Color control

00: -12 dB

••Sub; 00 h

Brightness

••Sub; 01 h

Color

~ 7F: 12dB

Brightness control

00: 1.75 V

1000000

:2.50V

~ 7F: 3.25 V (Pedestal Level)

~ 7F: 6.5 dB

Color control

1000000

:0dB

••Sub; 02 h

00:

-20 dB or less

00/01/28 16

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

ITEMS

BITS DESCRIPTIONS

Contrast control for RGB input

PRESET

100000

:6.2dB

0:

Cb/Cr internal

100000

:0dB

RGB Contrast

••Sub; 04 h

Cb/Cr SW

••Sub; 05 h

Sub-color

6

1

5

4

2

1

8

7

1

00: -8.0 dB

~ 3F: 11.4 dB 0.2Vinpuit

1: Cb/Cr external

Cb/Cr Switch

0: Cb/Cr internal

Sub color control (for Cb/Cr input)

00: -3 dB or less ~ 7F: +3 dB

Base band tint control (for Cb/Cr input)

••Sub; 05 h

B.B Tint

10000

:0deg

••Sub; 06 h

Sub-Contrast

••Sub; 10 h

ABL Start Point

••Sub; 10 h

ABL Gain

••Sub; 10 h

B. B.

••Sub; 06 h

Color •

••Sub; 11 h

RGB - Cutoff

••Sub; 12~14 h

G/B Drive

••Sub; 15~16 h

BLK

00: -12deg

1F: +12deg

Sub contrast control

0: -3 dB

1000

:0dB

~ F: 2.5 dB

Selecting ABL start point

00: 0V

00:0V

01: -0.20V 10: -0.30 V 11: -0.50 V

ABL Gain control

00: -0.21 V 01: -0.38 V 10: -0.50 V 11: -0.67 V

Blue Back Switch

00:-0.21V

0: FF

0: OFF

1: ON (50 IRE )

on/off the color •

0: OFF

0:OFF

1: ON

R,G,B Cutoff control

00: -0.65 V

G,B Drive control

00: -5.5 dB

00:-0.65 V

~ FF: 0.65 V

0000000

:0dB

~ 7F: 3.5 dB

Hor. And Vert. blanking for RGB outputs

0: Blanking ON ( Normal mode)

1: Blanking OFF

0

••Sub; 16 h

:Blanking ON

AKB System

6

00: AKB off(bus control)

11:AKB

cut

••Sub; 11 h

10: ACB cutoff

drive

-> align to targets

-> BUS control

off , drive

11: AKB cut off , drive -> align to targets

on / off the Y MUTE

Y-Mute

1

0:off

1:on

••Sub; 04 h

RGB-Mute

••Sub; 04 h

Ysm Mode

••Sub; 0F h

0: off

1: on

on / off the RGB mute

0: off

1: on

Select the Ys mode

0: Half tone mode (TV / HT / Ext RGB)

0:Half tone

mode

1: Blank

(TV / Ext RGB / Blank)

RGB ABCL

1

on / off the ABL / ACL for Ext. RGB

0: on

••Sub; 0F h

0: on

1: off

DEF STAGE

ITEMS

BITS DESCRIPTIONS

PRESET

Vertical Position

••Sub; 18 h

Horizontal Position

••Sub; 18 h

V-Freq

3

5

3

Vertical Position control by delaying the V-ramp timing

0:0H

0: 0H

~ 7: 7H

Horizontal Position control

00: -3ms

10000:0ms

000:AUTO

~ 1F: 3ms

Vertical frequency pull-in mode selection

000: AUTO

••Sub; 17 h

001: 50 Hz

010: 60 Hz

011: Forced 50Hz on no input

100:: Forced 312.5 H Stops V-synchronization

101: Forced 262.5 H Stops V-synchronization

110: Forced 313 H

111: Forced 263 H

Stops V-synchronization

00/01/28 17

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

ITEMS

BITS DESCRIPTIONS

PRESET

AFC Gain

••Sub; 1A h

2

Select AFC gain

00: Normal

00:Normal

01: 1 / 3 sensitivity

10: X 3 at V blanking duration

11: AFC OFF

0: off

V-stop

••Sub; 17 h

H STP

1

6

4

0:off

1: on

H OUT stop

0: normal

0:normal

100000:0%

1000:0%

••Sub; 17 h

312/313 Mode

••Sub; 17 h

V-AGC

••Sub; 17 h

Vertical Size

••Sub; 1A h

V Linearity

••Sub; 19 h

1 & Y-mute & RGB mute; H STOP

Synchronize the V freq. to 312/313

0: normal

1: TELETXT(312/313) Forced sync

1: X 5

V AGC sensitivity

0: normal

Vertical size alignment

00: -40 %

~ 3F: 40 %

V linearity alignment

0: 16 % at upper side , -20 % at lower side

~ F: -14 % at upper side , 17.5 % at lower side

V-S correction

0: 12 % at upper side , 15 % at lower side

~ F: -12 % at upper side , -15 % at lower side

Select the reference voltage

V-S Correction

••Sub; 19 h

4

1

1000:0%

V Ramp Ref.

0:External

••Sub; 17 h

0: External(YC Vcc)

1: Internal

AV SW, OTHERS

ITEMS

BITS DESCRIPTIONS

PRESET

Video SW

2

Video input selecting switch

00:TV

••Sub; 06 h

00: TV

01: EXT

(10: TV + C in)

(11: EXT + C in)

Au SW

1

2

Audio input selecting Switch

0:TV

••Sub; 06 h

STD by Mode

••Sub; 0D h

0: TV

1: EXT

Stand by mode

00,01: normal

00,:normal

10 : IF (Working IF Block ,IICBUS and 443VCXO)

11 : STD-by (Working IICBUS and 443VCXO )

Self Test

••Sub; 0E h

TEST

2

8

Selecting out put on AFT terminal for self Adjustment

00: AFT (Normal) 10: RF AGC X 1/2

00:AFT

(Normal)

00000000

For testing / Leave these bits preset data ; 0000 0000

••Sub; 1F h

00/01/28 18

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

READ MODE

item

bits

Description

preset

POR

1

Power on reset

0: normal

1: Resister Preset

1: Lock in

IF Lock Det

H Lock Det

IF level

1

IF lock detection

0: Lock out

Horizontal lock detection

0: Lock out

1: Lock in

IF AGC gain detection

0: High IF AGC gain

1: Low IF AGC gain

Monitoring the IF AGC level to detect if the IF input level is weak or

not.

( The threshold level is around 50 ~ 60 dB

Vertical Frequency

V Freq

1

3

0: 50 Hz

1: 60 Hz

Color System

Present color system status

000: B / W

010: M-PAL

100: 358 NTSC

110: SECAM

001: 4.43 PAL

011: N-PAL

101: 443 NTSC

111: N/A

Y-in

1

Y in for self diagnostic

0: no signal

1: detected

RGB OUT

H OUT

V OUT

PIF VCO Adj.

V Lock

AFT

RGB OUT for self diagnostic

0: no signal

H OUT for self diagnostic

0: detected

1: no signal

V OUT for self diagnostic

0: detected

1: no signal

Turn to 1 while the PIFVCO

0: normal

1: PIF VCO adjusting

1: detected

1

2

V Lock for self diagnostic

0: Lock out

AFT status

00: Lock OUT

10: too low

01: too high

11: Good

Sync Det

C-in DC

1

Detecting if the H sync. pulses are or are not.

0: no signal 1: detected

The DC voltage on C input terminal. It is for detecting the S-jack

swith.

0: open

1: Low

Product code

3

000: TB1258

010: TB1252

100: TB1254

110: TB1256

0: normal

001: TB1251

011: TB1253

101: TB1255

111: TB1257

1: overflowed

1: not warm up

1: finished

AKB Overflow

CRT Warm up

AKB Finish

STD/Non -Std

P-ID

1

0: normal

0: active

0: non-standard V freq.

0: detected

1: normal

1: Standard V freq.

1: not identified

0: Large noise level

1:error detect

1:NG

N-ID

S ID

Noise det

PIF VCO error detect

Coil error

0: normal

0: OK

00/01/28 19

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

DATA TRANSFER FORMAT VIA I²C BUS

Start and stop condition

SDA

SCL

S

P

Start con dition

Stop con dition

Bit transfer

SDA

SCL

SDA stable

Ch an ge of SDA allowed

Acknowledge

SDA by

tran sm itter

Th e tran sm itter releases th e SDA lin e (HIGH)

du rin g th e ackn owledge clock pu lse.

SDA by

receiver

Th e receiver h as to pu ll down th e SDA lin e

(LOW) du rin g th e ackn owledge clock pu lse.

SCL from

m aster

1

8

9

S

Clock pu lse for ackn owledgm en t

Data tran sm it form at 1

S

Slave address

0

A

Su b address

8bit

A

Tran sm it data

8bit

A

P

7bit

MSB

A : Ackn owledge

MSB

S : Start con dition

P : Stop con dition

Data tran sm it form at 2

S

Slave address

0

1

A

Su b address

Tran sm it data 1

A

Su b address

Tran sm it data n

A

P

Data received form at

S

Slave address

A

Received data 01

8bit

A

Received data 02

A

P

7bit

MSB

At the moment of the first acknowledge, the master transmitter becomes a master receiver and the slave receiver

becomes a slave transmitter. This acknowledge is still generated by the slave.

The Stop condition is generated by the master.

00/01/28 20

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Option al data tran sm it form at : au tom atic in crem en t m ode

S

Slave address

0

A

1

Su b address

A

Tran sm it data 1

8bit

Tran sm it data n

8bit

A

P

7bit

MSB

In this transmission methods, data is set on automatically incremented sub-address from the specified sub-address.

Purchase of TOSHIBA I²C components conveys a license under the Philips I²C Patent Rights to use these components

in an I²C system, provided that the system conforms to the I²C Standard Specification as defined by Philips.

00/01/28 21

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

MAXIMUM RATINGS (Ta=25•)

ITEM

SYMBOL

Vcc max9

Vcc max•

PD max

V in

RATING

UNIT

•

mW

V

•

Supply Voltage (9V Vcc)

Supply Voltage (5V Vcc)

Power Dissipation

Input terminal Voltage

Operating Temperature

Storage Temperature

12

8

1980(*1)

GND – 0.3 ~ Vcc + 0.3

-20 ~ 65

-55 ~ 150

Topr

Tstg

•

(*1)When using this device at above Ta=25•, the power dissipation decreases by 15.9mV per 1•rise.

(*2) This IC is not proof enough against a strong E-M field by CRT which may cause function errors and/or poor

Characteristics. Keeping the distance from CRT to the IC longer than 20 cm, or if cannot, placing shield metal

over the IC, is recommended in an application.

(*3)Pin 1,4,5,6,9,11,12,13,19,26,31,32,33,34,35,37,42,43,50,51 are weak against static electoricity and surge impulse.

Please take counter measure to meet, if necessary.

Ta-PD Curve ( on a PCB)

1980

1349

0

65

150

•@‚ƒ

Atmosphere Temperature

Ta (

)

RECOMMENDED OPERATING POWER SUPPLY VOLTAGE

PIN NO.

PIN NAME

MIN.

4.75

8.55

3.1

TYP.

5

9

3.3

5

MAX.

5.25

9.45

3.5

UNIT

NOTE

1

IF Vcc

V

•

14

31

37

42

RGB VCC (9V)

H VCC (9V)

DIGITAL VDD

Y/C VCC (5V)

4.75

5.25

In the condition that IIC BUS data “V

Ramp Ref.” is 0:External(Y/C Vcc),

the thermal drift of the Y/C Vcc

should be less than 50mV.

00/01/28 22

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

ELECTRICAL CHARACTERISTICS

CURRENT CONSUMTION

PIN NO.

PIN NAME

SYMBOL

Icc1

Icc14

Icc31

Icc37

CONDITION

Supply 5V

Supply 9V

Supply 3.3V

Supply 5V

MIN.

27.9

22.8

14.5

16.3

74.4

TYP.

37.2

30.4

19.3

21.7

99.2

MAX. UNIT

1

IF Vcc

46.5

38.0

24.1

27.1

124.0

mA

14

31

37

42

RGB VCC (9V)

H VCC (9V)

DIGITAL VDD

Y/C VCC (5V)

Icc42

DC CHARACTERISTIC

PIN VOLTAGE

PIN NO.

2

PIN NAME

SYMBOL

V2

CONDITION

MIN.

3.1

1.4

3.2

0.9

2.5

3

2.9

1.5

2.15

1.1

0.8

5.7

6

1.9

2.1

1.5

2.65

1.8

1.7

1.2

2

TYP.

3.8

3

MAX. UNIT

RIPPLE FILTER

SIF OUT

AUDIO OUT

IF IN

APC FILTER

X’TAL (4.43MHZ)

CW OUT

EXT. R IN

EXT. G IN

EXT. B IN

R OUT

4.5

3.6

4.2

2.1

3.9

3.6

3.7

2.9

2.85

1.7

1.4

6.4

7.5

2.6

2.8

3.5

3.35

2.4

3.1

1.9

3

V

3

4

6

V3

V4

V6

3.6

1.5

3.2

3.3

2.2

2.5

1.4

1.1

6.1

6.8

2.2

2.4

2.3

3

2.1

2.4

1.5

2.5

1.5

4.5

3.5

4.5

5.2

2.5

3

11

12

13

16

17

18

20

21

22

23

27

28

29

38

39

40

41

43

44

45

46

47

48

49

50

51

53

54

55

56

V11

V12

V13

V16

V17

V18

V20

V21

V22

V23

V27

V28

V29

V38

V39

V40

V41

V43

V44

V45

V46

V47

V48

V49

V50

V51

V53

V54

V55

V56

G OUT

B OUT

IK IN

REF. R

ABCL IN

H AFC FILTER

SYNC IN

Y IN

DC RESTOR

MON OUT

C-IN

Cr IN

Cb IN

EXT IN

LOOP FILTER

TV IN

DE-EMP

PIF VCO

EXT AUDIO IN

IF DET OUT

AFT OUT

H CORR/SIF IN

1.2

4

1.9

5

2.9

3.9

4.7

2

4.1

5.1

5.7

3

V

2.4

3.6

00/01/28 23

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

AC CHARACTERISTIC

PIF STAGE

ITEM

TEST

SYMBOL

MIN

TYP

MAX

UNIT

CIRCUIT CONDITON

PIF input sensitivity

PIF maximum input signal

PIF gain control range

RF AGC maximum output voltage

RF AGC minimum output voltage

RF AGC delay point (minimum)

RF AGC delay point (maximum)

PIF input resistance (*)

PIF input capacitance (*)

Differential gain

Differential phase

Intermodulation

Video output signal amplitude (Nega)

Video output signal amplitude (Posi)

Video output S/N

Synchronous signal level (Nega)

Synchronous signal level (Posi)

Video bandwidth (-3dB)

Capture range of the PLL (Upper)

Capture range of the PLL (Lower)

Hold range of the PLL (Upper)

Hold range of the PLL (Lower)

Control steepness of the VCO

vin min(p)

vin max(p)

RAGC(p)

VAGC max

VAGC min

v Dly min

v Dly max

Zin R(p)

Zin C(p)

DG

-

42

105

63

-

47

-

dB V

P1

100

53

dB

V

-

P2

P3

P4

-

0.3

80

-

5.0

-

2.4

-

70

110

dB V

100

-

40

2.0

50

k

•

pF

%

deg.

dB

V

2.0

45

2.2

55

2.6

8

3.5

-2.2

3.5

-2.2

3.0

P5

P6

DP

I M

V Det (p)n

V Det (p)p

S/N(p)

Vsync n

Vsync p

fDet(p)

fpH(p)

fpL(p)

fhH(p)

fhL(p)

P7

-

P8

dB

V

P9

P10

6

1.5

-

1.5

-

MHz

-

-1.5

-

-1.5

-

P11

P12

MHz/V

kHz/V

-

Steepness of the AFT Detection

(steep)

SAFT(S)

SAFT(G)

20

75

25

30

Steepness of the AFT Detection

(gentle)

P13

P14

100

125

AFT maximum output voltage

AFT minimum output voltage

AFT output voltage on defeating

VAFT max

VAFT min

•AFT Def

-

4.5

-

2.3

4.8

0.2

2.5

-

V

0.5

2.7

(*) Not tested

SIF STAGE

ITEM

TEST

CIRCUIT

TEST

CONDITION

SYMBOL

MIN

TYP

MAX

UMIT

vin lim(s)4.5MH

vin lim(s)4.5ML

vin lim(s)5.5M

vin lim(s)6.0M

vin lim(s)6.5M

AMR4.5MH

AMR 4.5ML

AMR5.5M

Limiting sensitivity (4.5MHz High)

Limiting sensitivity (4.5MHz Low)

Limiting sensitivity (5.5MHz)

Limiting sensitivity (6.0MHz)

Limiting sensitivity (6.5MHz)

AM reduction ratio (4.5MHz High)

AM reduction ratio (4.5MHz Low)

AM reduction ratio (5.5MHz)

AM reduction ratio (6.0MHz)

AM reduction ratio (6.5MHz)

AF output signal amplitude (4.5MHz

High)

AF output S/N AF output signal

amplitude (4.5MHz High)

Total harmonics distortion AF output

signal amplitude (4.5MHz High)

AF output signal amplitude (4.5MHz

Low)

-

45

40

45

55

50

45

50

-

S1

S2

-

50

dB

AMR6.0M

AMR6.5M

mVrms

vDet(s)4.5MH

S/N(s)4.5MH

THD4.5MH

-

649

50

-

927

55

1324

-

S3

S4

dB

%

0.5

500

1.0

710

mVrms

vDet(s)4.5ML

350

00/01/28 24

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST

CIRCUIT

TEST

CONDITION

ITEM

SYMBOL

S/N(s)4.5ML

THD4.5ML

vDet(s)5.5M

S/Ns)5.5M

THD5.5M

vDet(s)6.0M

S/N(s)6.0M

THD6.0M

vDet(s)6.5M

S/N(s)6.5M

THD6.5M

fpH(s)1

MIN

50

-

TYP

55

0.5

927

58

0.5

927

58

0.5

927

58

0.5

-

MAX

UMIT

AF output S/N AF output signal

amplitude (4.5MHz Low)

Total harmonics distortion AF output

signal amplitude (4.5MHz Low)

AF output signal amplitude

(5.5MHz)

AF output S/N AF output signal

amplitude (5.5MHz)

Total harmonics distortion AF output

signal amplitude (5.5MHz)

AF output signal amplitude

(6.0MHz)

AF output S/N AF output signal

amplitude (6.0MHz)

Total harmonics distortion AF output

signal amplitude (6.0MHz)

AF output signal amplitude

(6.5MHz)

AF output S/N AF output signal

amplitude (6.5MHz)

Total harmonics distortion AF output

signal amplitude (6.5MHz)

Demodulation band width of the FM

demodulator (Upper1)

Demodulation band width of the FM

demodulator (Lower1)

Demodulation band width of the FM

demodulator (Upper2)

Demodulation band width of the FM

demodulator (Lower2)

Audio attenuater gain (Max)

Audio attenuater gain (Mid)

Audio attenuater gain (Min)

Audio attenuater off-set

-

1.0

1236

-

dB

%

mVrms

-

695

53

-

S5

S6

dB

%

1.0

1236

-

mVrms

695

53

dB

%

-

695

53

-

1.0

1236

-

mVrms

S7

S8

dB

%

1.0

-

5.0

-

fpL(s)1

-

4.0

-

fpH(s)2

7.0

-

S9

MHz

dB

fpL(s)2

-

5.0

G att max

G att mid

G att min

Vos att

CT(s)T-E

CT(s)E-T

Vos sw

-

-2

-

0

2

-

S10

-15

-85

50

-75

-60

-

-75

+150

-65

-55

S11

S12

S13

-50

mV

dB

Audio switch cross-talk (TV•EXT)

Audio switch cross-talk (EXT•TV)

Audio switch off-set

-

mV

±

30

(*) Not tested

VIDEO STAGE

ITEM

TEST

CIRCUIT

TEST

CINDITION

SYMBOL

MIN

TYP

MAX

UNIT

TV Input Dynamic range

External Input Dynamic Range

TV mode Gain

External mode Gain

AV SW Cross Talk (TV -> Ext)

AV SW Cross Talk (Ext -> TV)

Y Input Dynamic Range

Y Input Pedestal Clamp Voltage

Y frequency response

Y Delay time

DR_TV

DR_EXT

G_TV

V1

0.9

5.7

1.0

6.0

V p-p

dB

Vp-p

V

MHz

ns

•

V2

V3

6.3

-50

•

2.9

•

550

-34

254

44

3.70

2.80

2.20

19.0

13.2

G_EXT

5.7

6.0

CT_SWTE

CT_SWET

••_Y

-60

0.9

2.5

6.5

370

-44

214

34

2.80

2.20

1.30

4.70

10.2

-55

1.0

2.7

8.0

460

-38

238

38

3.25

2.50

1.75

11.8

11.6

V4

V5

V6

V7

•

YCLP

FR_Y

t_YDEL

-40ns

240ns

1step

t_YDEL-40

t_YDEL240

t_{YDEL 1step}

V_BRTMAX

V_BRTCEN

V_BRTMIN

•V_BRT

Brightness Control Characteristics

V8

V9

V

Brightness Control resolution

Uni-color Control Characteristics

MV/bit

dB

•

UCYMAX

00/01/28 25

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST

CIRCUIT

TEST

CINDITION

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

4.2

-9.8

1.5

5.7

-7.8

2.5

7.2

-5.8

3.5

•

UCYCEN

UCYMIN

Sub Contrast Control Characteristics

V10

dB

•

SCONMAX

-4.0

2.05

3.6

-3.0

2.75

6.6

-2.0

3.80

9.6

•

SCONMIN

Sharpness Peaking Frequency

Sharpness Control Characteristics

V11

V12

MHz

dB

•

SHP

•

SHMAX

1.3

3.3

5.

•

SHCEN

-8.4

-5.4

-2.4

•

SHMIN

Y •correction start point

V_Y

V13

V14

V15

70

77

84

73

80

87

76

83

90

IRE

_•70

V_Y

_•80

V_Y

_•90

Y •correction curve

Black Expansion AMP Gain

Black Expansion Start Point

G_Y

-5

1.2

25

34

dB

V

•

1.05

21

30

1.45

29

38

•

BLEX

V_{BLEX 25IRE}

V_{BLEX 35IRE}

V_{BLEX 45IRE}

39

85

43

90

47

95

DC restration gain

V_dcrest85

IRE

V_dcrest120

V_{dcrest step}

V_WPS

G_TRAP358

G_TRAP443

G_HTY

110

5

2.5

•

-6.5

115

8

2.8

-29

-27

-6

120

11

3.3

-25

-23

-5.5

WPS Level

Chroma Trap Gain

V16

V17

Vp-p

dB

Half Tone reduction for Y

V18

dB

CHROMA STAGE

ITEM

TEST

CIRCUIT

TEST

CINDITION

SYMBOL

MIN

TYP

MAX

UNIT

ACC Chara.

C1

25

40

•

mV p-p

•

600

•

ACCL

1000

5.16

1.86

4.45

1.86

4.30

1.92

3.67

1.92

•

ACCH

TOF Chara.(4.43)

BPF Chara. (4.43) fo

TOF Chara. (3.58)

BPF Chara. (3.58)

fo

Q

C2

MHz

•

MHz

•

MHz

•

MHz

•

0T443

•

T443

•

0B443

Q

fo

Q

fo

Q

•

B443

•

0T358

•

T358

•

0B358

•

B358

595

510

765

-60

4.0

•

-27

28

-28

28

700

600

805

690

1035

60

8.0

-20

-21

56

-56

56

C Delay Time (P/N)

t_CDELPN

t_CDELS

C3

C4

ns

C Delay Time (SECAM)

Time Difference between Y / C

Color Control Characteristics MAX

MIN

Uni-Color Control Characteristics

900

0

6.5

•

-24

42

•

t

Y/C

dB

•

COLMAX

•

COLMIN

C5

C6

dB

deg

UCCMIN

TINT Chara.(4.43NTSC)

MAX

MIN

MAX

MIN

R/B

G/B

R/B

G/B

R/B

G/B

R/B

G/B

••_443MAX

••_443MIN

••_358MAX

••_358MIN

V_PR/B

V_PG/B

V_NR/B

V_NG/B

V_NR/B

-42

42

TINT Chara.(3.58NTSC)

-28

-42

0.57

0.38

0.72

0.32

0.80

0.30

0.77

0.44

-56

Relative Amplitude (PAL)

Relative Amplitude (NTSC1)

Relative Amplitude (NTSC2)

Relative Amplitude (DVD)

C7

0.47

0.31

0.62

0.26

0.70

0.24

0.67

0.36

0.67

0.45

0.82

0.38

0.90

0.36

0.87

0.52

•

V_NG/B

V_NR/B

V_NG/B

00/01/28 26

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST

CIRCUIT

TEST

CINDITION

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

Relative Phase (PAL)

R-B

G-B

R-B

G-B

R-B

G-B

R-B

G-B

C8

84

230

83

232

95

89

236

89.5

241

105

240

92.8

245

500

2.5

1.1

1.5

1.9

3.4

5.0

1.3

2.1

4

94

242

95

deg

•

PR-B

•

PG-B

Relative Phase (NTSC1)

Relative Phase (NTSC2)

Relative Phase (DVD)

•

N1R-B

248

115

248

100

254

2500

-2500

2500

-2500

2500

-2500

2500

-2500

3.5

1.6

3

4

6

8

2.6

4.2

7

•

N1G-B

•

N2R-B

232

86

•

N2G-B

•

DVDR-B

236

350

300

1.5

0.6

0.7

1.0

1.7

2.5

0.6

•

DVDG-B

APC Pull- In Range (4.43MHz)

APC Hold Range (4.43MHz)

APC Pull-In Range (3.58MHz)

APC Hold Range (3.58MHz)

C9

Hz

•

4APCP+

•

-

4APCP

4APCH+

•

4APCH-

•

3APCP+

•

3APCP-

3APCH+

•

3APCH-

APC Control Sensitivity (4.43MHz)

APC Control Sensitivity (3.58MHz)

PAL ID Sensitivity (Normal Mode)

Hz/mV

mVp-p

•

443

C10

C11

358

•

PIDON

PIDOFF

PIDLON

•

PAL ID Sensitivity (Low Mode)

NTSC ID Sensitivity (Normal Mode)

NTSC ID Sensitivity (Low Mode)

•

PIDLOFF

•

NIDON

NIDOFF

NIDLON

1.0

2.0

•

4.0

0.35

1.0

8

12

0.65

2.0

4.0

-5.3

4.5

•

NIDLOFF

CWOUT Amplitude

DC Bias at killer on

DC Bias at killer off

Half Tone Chara. for C

Sub-Color Control

Characteristics

1H Delay Time

C12

0.5

1.5

3.5

-6.0

+3.5

-3.5

64

V p-p

V

•

CW

V_BCWKON

V_BCWKOFF

3.0

C13

C14

-6.7

+2.5

-4.5

dB

•

HTC

MAX

MIN

•

SCOLMAX

-2.5

•

SCOLMIN

T_BDL

T_RDL

•

s

64

SECAM STAGE

TEST

CIRCUIT

TEST

CINDITION

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

Bell Monitor Output Amplitude

Bell Filter f0

Bell Filter f0 Variable Range

embo

f_0B-C

f_0B-VR

Q_BEL

VBS

SE1

SE2

SE3

SE4

SE5

63

-23

15

13

1.29

100

0

30

15

1.85

163

23

45

17

2.41

mV p-p

kHz

Bell Filter Q

Color Difference Output Amplitude

Vp-p

VRS

R/B-S

SNB-S

SBR-S

LinB

1.12

0.7

-38

-44

85

1.57

0.80

-34

2.22

0.90

-28

Color Difference Relative Amplitude

Color Difference S/N Ratio

SE6

SE8

-

dB

-39

-32

Linearity

SE9

SE10

SE11

100

1.1

117

1.5

%

LinR

85

Rising-Fall Time

trfB

-

•

s

trfR

-

1.1

1.5

SECAM ID Sensitivity

(Normal Mode)

H

0.66

1.82

1.32

3.64

2.64

6.5

mV

•

SIDHON

•

SIDHOFF

00/01/28 27

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST

CIRCUIT

TEST

CINDITION

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

H+V

H

0.6

1.0

1.7

4.5

1.1

2.8

1.7

1.9

2.1

80

1.20

1.9

3.3

9

2.2

5.6

1.8

2.0

2.2

85

2.4

3.8

6.0

14

4.4

10

1.9

2.1

2.3

90

•

SIDHVON

•

SIDHVOFF

SECAM ID Sensitivity

(Low Mode)

•

SIDLHON

•

SIDLHOFF

H+V

•

SIDLHVON

•

SIDLHVOFF

Gate Pulse Width Variable Range

WGP₊₂₀₀

WGP

SE12

SE13

•s

WGP_-200

V_SBMAX

V_SRMAX

V_SRMIN

•V_SB

SECAM black adjustment

characteristic

mV

80

85

90

-97

12

-92

14

-87

16

SECAM black adjustment sensitivity

12

14

16

•V_SR

TEXT STAGE

TEST

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

CIRCUIT CINDITION

V-BLK Pulse Output Level

H-BLK Pulse Output Level

RGB Output Black Level (0IRE DC)

RGB Output White Level (100IRE

AC)

0.1

2.25

0.6

2.5

1.1

2.75

•

VBLK

T1

T2

T3

T4

V

•

HBLK

•

BLACK

2.50

Vp-p

V

•

WHITE

•

Cut-Off Voltage Variable Range

0.6

-0.7

2.5

-8.0

5.7

0.65

-0.65

3.5

-5.5

6.0

0.7

-0.6

4.5

-4.5

6.3

•

CUT+

•

CUT-

Drive Control Variable Range

ABCL Control Voltage Range

T5

T6

dB

V

DR+

DR-

•

ABCLH

4.5

4.8

5.1

•

ABCLL

ACL Gain

ABL Point

-21

-19

0

-17

0.1

dB

V

•

ACL

T7

T8

-0.1

-0.3

-0.4

-0.6

-0.31

-0.48

-0.60

-0.77

0.7

0.59

0.34

0.06

2.8

•

ABLP1

-0.2

-0.3

-0.5

-0.21

-0.38

-0.50

-0.67

-

0.74

0.41

0.08

3.25

-0.1

-0.2

-0.3

-0.11

-0.28

-0.40

-0.57

-

•

ABLP2

•

ABLP3

•

ABLP4

ABL Gain

V

•

ABLG1

•

ABLG2

•

ABLG3

•

ABLG4

Analog RGB Dynamic Range

Analog RGB Contrast Control MAX.

Characteristic

T9

T10

Vp-p

••_TX

0.94

0.49

0.1

•

TXCMAX

CEN.

TXCCEN

MIN.

MAX.

TXCMIN

Analog RGB Brightness

T11

3.7

Vp-p

TXBRMAX

Control Characteristic

CEN.

MIN.

2.2

1.3

2.5

2.8

2.2

•T_XBRCEN

1.75

3.3

0.7

40

•

TXBRMIN

Analog RGB Mode Switching Level

T12

T13

•

YSHALF

V

ns

•

YSBLK

Analog RGB Mode Transfer

Characteristic

100

••_YS

t••_YS

••_YS

t••_YS

•

40

Half Tone Mode Switching Level

Cross Talk from Analog RGB to••

Cross Talk from ••to Analog RGB•

T14

T15

T16

0.7

-55

V

dB

•

HT

-40

••_TX-TV

••_TV-TX

•

00/01/28 28

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

CIRCUIT CINDITION

••_BBMAX

••_BBMIN

•V_R-G

•V_G-B

•V_B-R

Baseband TINT Characteristic

T17

7

-7

-40

12

-12

17

-17

40

deg

Analog RGB / RGB Output Voltage

Axes Difference

T18

mV

DEF STAGE

TEST

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

CIRCUIT CINDITION

AFC Inactive Period

50Hz

60Hz

308-7

260-10

5.0

H

•

••

•

4.7

38.5

•

5.3

42.5

50AFCOFF

•

60AFCOFF

H-OUT Start Voltage

H-OUT Pulse Duty

H-OUT Freq. On AFC Stop Mode

Horizontal Free-Run Frequency 50Hz

60Hz

•

HON

••

•

kHz

40.5

•

HOUT

15.585 15.734 15.885

15.475 15.625 15.775

15.585 15.734 15.885

16.200 16.400 16.600

14.600 14.900 15.200

•

HAFCOFF

•

H50FR

•

H60FR

Horizontal Freq. Variable

Range

MAX.

MIN.

kHz

•

HMAX

••

•

HMIN

Horizontal Freq. Control Sensitivity

Horizontal Pull-In Range

1.3

500

4.0

•

-20

2.7

0.2

6.3

3.3

0.8

7.5

13.5

2.8

1.8

4.7

45

55

45

55

•

3.0

•

1.8

•

4.4

0.15

0

3.2

0.3

6.8

3.6

1.3

8.0

14.0

3.0

2.0

5.0

50

60

50

2.3

•

Hz/mV

Hz

•

••

HAFC

HPH

HPL

H-OUT Voltage

4.8

0.30

20

3.7

0.4

7.3

3.9

1.6

8.5

14.5

3.2

2.2

5.3

55

65

55

65

•

V

•

HOUTH

••

•

HOUT

Horizontal Freq. Dependence on •cc

FBP Phase

H-Sync. Phase

Horizontal Position Variable Range

AFC-2 Pulse Threshold Level

H-BLK Pulse Threshold Level

BLACK Peak Det. Stop Period (H)

••_HVCC

••_FBP

••_HSYNC

•••_HPOS

•

•HBPDET

•BPDET

••_GP

•

•••

Hz/V

•

s

•••

•

s

V

AFC2

HBLK

•s

Gate Pulse Start Phase

Gate Pulse Width

Vertical Oscillation Start Voltage

Vertical Free-Run Frequency Auto₅₀

Auto₆₀

••6

•

s

GP

V

Hz

••7

•18

VON

•

VAUFR50

•

VAUFR60

50Hz

60Hz

•

V50FR

60

•

V60FR

Gate Pulse V-Masking Period 50Hz

60Hz

V.Ramp DC on Service Mode

Vertical Pull-In Range (Auto)

308-7

260-10

3.2

H

•

50GPM

•19

•

60GPM

•

3.4

•

V

H

•

•20

•21

NOVRAMP

224.5

343.5

274.5

343.5

224.5

293.5

312.5

262.5

313

263

29

•

VPAUL

•

VPAUH

•

Vertical Pull-In Range (50Hz)

Vertical Pull-In Range (60Hz)

F_VP50L

F_VP50H

•

VP60L

•

VP60H

Vertical Period on Fixed Mode

T_V312.5

T_V262.5

T_V313

H

•

22

•

27

•

31

•

V263

V-BLK Start Phase

V-BLK Width

50Hz

60Hz

50Hz

60Hz

••_50VBLK

••_60VBLK

•23

•

s

29

22

18

H

•

50VBLK

•

60VBLK

00/01/28 29

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST

ITEM

SYMBOL

MIN

TYP

MAX

UNIT

CIRCUIT CINDITION

Sand Castle Pulse Level

6.70

4.60

1.55

1.50

18

1.8

•

11

1.74

43

-51

-23

21

7.00

4.90

1.85

1.67

22

2.3

0.0

15

1.90

47

-47

-21

24

7.30

5.20

2.15

1.83

26

2.8

0.3

19

2.06

51

-43

-18

27

V

•

•24

SCPH

•

SCPM

•

SCPL

Vertical Ramp Amplitude

Vertical AMP Gain

Vertical AMP MAX. Output Level

Vertical AMP Min. Output Level

Vertical AMP Max. Output Current

Vertical NFB Amplitude

Vp-p

dB

V

•

VRAMP

•25

•26

•

VAMP

•

VOMAX

•

VOMIN

mA

Vp-p

%

•

VOMAX

•27

•28

•

NFB

••_VRAMPH

••_VRAMPL

••_LIN1+

••_LIN1-

••_LIN2+

••_LIN2-

••_S1+

••_S1-

••_S2+

••_S2-

•

Vertical Amplitude Variable Range

Vertical Linearity Variable Range

Vertical S Correction Variable Range

Vertical Guard Voltage

%

V

•29

•30

•31

17

20

23

-28

-26

21

-26

21

-25

-23

24

-23

24

-22

-20

27

-20

27

1.80

2.00

2.20

VG

00/01/28 30

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEST CONDITION

PIF STAGE

Note Items/Symbols

Bus conditions

Measurement methods

P1

RF AGC:except 0

PIF Freq. :

38.9MHz

VCO Adj. Center

:•

(1)Input a signal that 38.9[MHz], 90[dB V], and 30 [%] modulated

by 15 [kHz] sine wave at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

(3)Measure the amplitude at Pin 54(vo#54 [Vp-p]).

(4)Decreasing the IF input level, measure the input level at which

the output amplitude at pin 54 turns to be –3dB against “vo#54”

(vin min(p)[dB V]).

PIF Input Sensitivity

/ vin min(p)

PIF maximum input

signal

/ vin max(p)

0/1

PIF gain control range

/ RAGC(p)

Others : Preset

(5)Increasing the IF input level, measure the input level at which

the output amplitude at pin 54 turns to be -1dB against “vo#54”

(vin min(p)[dB V]).

(6)RAGC(p)[dB] = vin max(p) - vin min(p)

P2

P3

RF AGC output

voltage

/ VAGC max

/ VAGC min

RF

(1)Input a 38.9[MHz], 90[dB V] signal at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

(3)Adjust RF AGC so that the pin 9 voltage is 4.5V.

(4)Increase the IF input level to 107dBuV.

(5)Measure the pin 9 voltage (VAGC min[V]).

(6)Connect pin 6 and pin 7 to GND.

(7)Measure the pin 9 voltage (VAGC max[V]).

(1)Input a 38.9[MHz], 90[dB V] signal at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

AGC•:•Adjust

PIF Freq. :

38.9MHz

VCO Adj. Req.:

•0/1

Others : Preset

RF delay point

/ v Dly min

/ v Dly max

RF

AGC•:•Adjust

PIF Freq.

38.9MHz

(3)Set the data of “RF AGC” to 01(h).

VCO Adj. Req. :

•0/1

RF AGC: 01/3F

Others : Preset

(4)Decrease the IF input level, measure the input level at which the

voltage at pin 9 turn to be 4.5[V] (v Dly min[dB V]).

(5)Set the data of “RF AGC” to 3F(h).

(6)Increase the IF input level, measure the input level at which the

voltage at pin 9 turn to be 4.5[V] (v Dly max[dB V]).

(1)Remove all connection from pin 6 and pin 7.

(2)Measure the resistance (Zin R(p)[k ]) and capacitance (Zin

C(p)[pF]) of pin 6 and pin 7 by the impedance meter.

P4

P5

Preset

PIF input resistance

/ Zin R(p)

PIF input capacitance

/ Zin C(p)

Differential Gain

/ DG

RF AGC:except 0

PIF Freq.:

38.9MHz

VCO Adj. Req.:

0/1

Vi Pol:0/1

(1)Input a signal that 38.9[MHz], 90[dB V], and 87.5 [%] modulated

by 10 stair video signal at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

Differential Phase

/ DP

(3)Measure "DG[%]" and "DP[deg]" for Pin54 output.

Others : Preset

P6

Intermodulation

/ IM

RF AGC:except 0 (1)Input a signal composed of following 3 signals at pin 6;

PIF Freq. :

38.9MHz

VCO Adj. Req.:

0/1

38.90[MHz]/90[dB V],

34.47[MHz]/80dB V]

33.40[MHz]/80[dB V]

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Others : Preset

Req.” to “0”.

(3)Adjust pin 10 voltage so that the bottom of pin 54 output is equal

to sync. tip level.

(4)Measure the 1.07[MHz] level against the 4.43[MHz] level(=0[dB])

(IM[dB]).

00/01/28 31

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditions

RF AGC:except 0

PIF Freq. :

38.9MHz

VCO Adj. Req. :

0/1

Measurement methods

P7

Video output signal

amplitude

(1)Input a signal that 38.9[MHz], 90[dB V], and 87.5 [%] negative

modulated by 100% white video signal at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

/ vDet(p)n

/ vDet(p)p

(3)Set the bit of “L-SECAM MODE” to “0”.

L-SECAM MODE

:0/1

Others : Preset

(4)Measure the amplitude of the pin 54 output signal (vDet(p)n[Vp-

p]).

(5)Input a signal that 38.9[MHz], 90[dB V], and 97 [%] positive

modulated by 100% white video signal at pin 6.

(6)Set the bit of “L-SECAM MODE” to “1”.

(7)Measure the amplitude of the pin 54 output signal (vDet(p)p[Vp-

p]).

P8

P9

Video output S/N

/ S/N(p)

RF AGC:except 0

PIF Freq. :

38.9MHz

VCO Adj. Req. :

0/1

Others : Preset

RF AGC:except 0

PIF Freq. :

38.9MHz

VCO Adj. Req.:

0/1

(1)Input a signal that 38.9[MHz], 90[dB V], and 87.5 [%] modulated

by black video signal at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

(3)Measure the video S/N for pin 54 output (HPF : 100[kHz], LPF :

5[MHz], CCIR weighted) (S/N(p)[dB]).

(1)Input a signal that 38.9[MHz], 90[dB V], 87.5[%] negative

modulated by 100% white signal at pin 6.

Synchronous signal

level

/ Vsync n

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

(3)Set the bit of “L-SECAM MODE” to “0”.

/ Vsync p

L-SECAM MODE

:0/1

Others : Preset

(4)Measure the voltage of the sync. tip at pin 54 (Vsync n[V]).

(5)Input a signal that 38.9[MHz], 90[dB V], and 97 [%] positive

modulated by 100% white video signal at pin 6.

(6)Set the bit of “L-SECAM MODE” to “1”.

(7)Measure the voltage of the sync. tip at pin 54 (Vsync p[V]).

(1)Input the mixture of 2 signals (signal1 : 38.9[MHz]/82[dB V],

signal 2 : 38.8[MHz]/69[dB V]) to pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

(3)Measure the minimum voltage of the output signal at pin 54

(Vo#54).

(4)Apply the DC voltage to pin 10 and adjust it so that the minimum

voltage of the output signal at pin 54 is equal to Vo#54.

(5)Decrease frequency of the input signal 2 at pin 6, and measure

amplitude of the output signal at pin 54.

P10

Video bandwidth

(-3dB)

/ fDet(p)

RF AGC:except 0

PIF Freq.:

38.9MHz

VCO Adj. Req.:

0/1

L-SECAM MODE

:0/1

Others : Preset

(6)Measure fDet(p) shown as below.

3[dB]

Ref.level

f Det(p)

Frequency of

the output signal at pin54

100[kHz]

00/01/28 32

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditions

RF AGC : except

0

PIF Freq. :

38.9MHz

VCO Adj. Req. :

0/1

Others : Preset

Measurement methods

(1)Input a signal that 38.9[MHz], 90[dB V] at pin 6.

(2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.

Req.” to “0”.

(3)Sweep down the input signal frequency to 34.9[MHz], and

sweep up to 43.9[MHz]. Sweep down the input signal frequency

to 38.9[MHz].

P11

Capture range of the

PLL

/ fpH(p)

/ fpL(p)

Hold range of the PLL

/ fhH(p)

(4)Measure the voltage at pin 55 and measure the frequency of the

input signal shown as below.

/ fhL(p)

f h(p)L f p(p)L

38.9[MHz]

f p(p)H

f h(p)H

Frequency of

the input signal

P12

Control steepness of PIF Freq. :

(1) Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO

Adj. Req.” to “0”.

(2) Set the FET probe which connected to the spectrum analyzer

near by pin 50 or pin 51 (Don’t touch the probe directly to pin 50

or to pin 51).

the VCO

/

38.9MHz

VCO Adj. Req. :

0/1

Others : Preset

(3) Apply 2.3[V] to pin 47, and measure frequency of the VCO

oscillation by the spectrum analyzer (fLVCO[MHz]).

(4) Apply 2.7[V] to pin 47, and measure frequency of the VCO

oscillation by the spectrum analyzer (fHVCO[MHz]).

(5) [MHz/V] = (fHVCO-fLVCO)/0.4

P13

Steepness of the AFT PIF Freq. :

(1) Input a 38.9[MHz], 90[dB V] signal at pin 6.

(2) Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO

Adj. Req.” to “0”.

(3) Input a 38.9[MHz]-20[kHz], 90[dB V], non-modulation signal at

pin 6.

(4) Measure the voltage at pin 55 (VH#55[V]).

(5) Input a 38.9[MHz]+20[kHz], 90[dB V], non-modulation signal

at pin 6.

detection

/ S AFT

AFT Voltage

/ VAFTmax

/ VAFTmin

38.9MHz

VCO Adj. Req.:

0/1

Others : Preset

(6) Measure the voltage at pin 55 (VL#55[V]).

(7) S AFT[kHz/V] = 40/(VH#55-VL#55)

(8) Input a 38.9[MHz]-500[kHz], 90[dB V], non-modulation signal

at pin 6.

(9) Measure the voltage at pin 55 (VAFTmax[V]).

(10) Input a 38.9[MHz]+500[kHz], 90[dB V], non-modulation signal

at pin 6.

(11) Measure the voltage at pin 55 (VAFTmin[V]).

P14

AFT output voltage on Preset

defeating

(1)Measure the voltage at pin 55 (VAFT Def[V]).

00/01/28 33

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

SIF STAGE

Note Items/Symbols

Bus conditions

SIF-Freq. :

4.5M/5.5M/6.0M/

6.5M

AUDIO ATT : 127

Others : Preset

Measurement methods

(1) Set the bits of “SIF-Freq.” to “11”.

S1

Limiting sensitivity

/ vin lim(s)4.5MH

/ vin lim(s)4.5ML

/ vin lim(s)5.5M

/ vin lim(s)6.0M

/ vin lim(s)6.5M

(2) Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

400[Hz] sine wave at pin 56.

(3) Measure the amplitude at pin 4 (vo#4[mVrms]).

(4) Decreasing the 4.5[MHz] signal level, measure the 4.5[MHz]

signal level at which the amplitude at pin 4 turns to be –3[dB]

against “vo#4” (vin lim(s)4.5MH[dB V]).

(5) Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

400[Hz] sine wave at pin 56.

(6) Do same measuring as above (3)~(4) (vin lim(s)4.5ML).

(7) Set the bits of “SIF-Freq.” to “00”.

(8) Change the frequency of the input signal to 5.5MHz, and

change the deviation of the input signal to 50[kHz].

(9) Do same measuring as above (3)~(4) (vin lim(s)5.5M).

(10) Set the bits of “SIF-Freq.” to “01”.

(11) Change the frequency of the input signal to 6.0MHz, and do

same measuring as above (3)~(4) (vin lim(s)6.0M).

(12) Set the bits of “SIF-Freq.” to “10”.

(13) Change the frequency of the input signal to 6.5MHz, and do

same measuring as above (3)~(4) (vin lim(s)6.5M).

(1) Set the bits of “SIF-Freq.” to “11”.

(2) Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

400[Hz] sine wave at pin 56.

(3) Measure the amplitude at pin 4 (vo#4[mVrms]).

(4) Input a signal that 4.5[MHz], 100[dB V], and 30 [%] modulated

by 400 [Hz] sine wave at pin 56.

S2

AM reduction ratio

/ AMR4.5MH

/ AMR4.5ML

/ AMR5.5M

/ AMR6.0M

/ AMR6.5M

SIF-Freq. :

4.5M/5.5M/6.0M/

6.5M

AUDIO ATT : 127

Others : Preset

(5) Measure the amplitude at pin 4 (v#4[mVrms]).

(6) AMR4.5H[dB] = 20log(v#4/ vo#4)

(7) Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

400[Hz] sine wave at pin 56.

(8) Do same measuring as above (3)~(6) (AMR4.5ML).

(9) Set the bits of “SIF-Freq.” to “00”.

(10) Change the frequency of the input signals to 5.5MHz, and

change the deviation of the input signal to 50[kHz].

(11) Do same measuring as above (3)~(6) (AMR5.5M).

(12) Set the bits of “SIF-Freq.” to “01”.

(13) Change the frequency of the input signals to 6.0MHz, and do

same measuring as above (3)~(6) (AMR6.0M).

(14) Set the bits of “SIF-Freq.” to “10”.

(15) Change the frequency of the input signals to 6.5MHz, and do

same measuring as above (3)~(6) (AMR6.5M).

S3

SIF-Freq. : 4.5M

AUDIO ATT : 127

Others : Preset

(1)Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

1[kHz] sine wave at pin 56.

AF output signal

amplitude

(2)Measure the amplitude at pin 4 (vDet(s)4.5MH[mVrms]).

(3)Measure the total harmonics distortion at pin 4 (THD4.5MH[%]).

(4)Input a 4.5[MHz], 100[dB V] signal at pin 56.

(5)Measure the amplitude at pin 4 (vn(s)[mVrms]).

(6)S/N4.5MH[dB] = 20log(vDet(s)/vn(s))

/ vDet(s)4.5MH

AF output S/N

/ S/N(s)4.5MH

Total harmonics

distortion

/ THD4.5MH

S4

SIF-Freq. : 4.5M

AUDIO ATT : 127

Others : Preset

(1)Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

1[kHz] sine wave at pin 56.

(2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)4.5ML,

S/N(s)4.5ML, THD4.5ML).

AF output signal

amplitude

/ vDet(s)4.5ML

AF output S/N

/ S/N(s)4.5ML

Total harmonics

distortion

/ THD4.5ML

00/01/28 34

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditions

SIF-Freq. :5.5M

AUDIO ATT : 127

Others : Preset

Measurement methods

(1)Input a signal that 5.5[MHz], 100[dB V], 50[kHz] deviated by

400[Hz] sine wave at pin 56.

(2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)5.5M,

S/N(s)5.5M, THD5.5M).

S5

AF output signal

amplitude

/ vDet(s)5.5M

AF output S/N

/ S/N(s)5.5M

Total harmonics

distortion

/ THD5.5M

S6

SIF-Freq. : 6.0M

AUDIO ATT : 127

Others : Preset

(1)Input a signal that 6.0[MHz], 100[dB V], 50[kHz] deviated by

400[Hz] sine wave at pin 56.

(2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)6.0M,

S/N(s)6.0M, THD6.0M).

AF output signal

amplitude

/ vDet(s)6.0M

AF output S/N

/ S/N(s)6.0M

Total harmonics

distortion

/ THD6.0M

S7

SIF-Freq. : 6.5M

AUDIO ATT : 127

Others : Preset

(1)Input a signal that 6.5[MHz], 100[dB V], 50[kHz] deviated by

400[Hz] sine wave at pin 56.

(2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)6.5M,

S/N(s)6.5M, THD6.5M).

AF output signal

amplitude

/ vDet(s)6.5M

AF output S/N

/ S/N(s)6.5M

Total harmonics

distortion

/ THD6.5M

S8

Demodulation band

width of the FM

demodulator

/ fpH(s)1

SIF-Freq. : 4.5M

AUDIO ATT : 127

Others : Preset

(1)Input a signal that 4.5[MHz], 100[dB V], 25[kHz] deviated by

400[Hz] sine wave at pin 56.

(2)Measure the amplitude at pin 4(vo#4 [Vp-p]).

(3)Increase the input signal frequency, measure the input signal

frequency at which the output amplitude at pin 4 turn to be -

3[dB] against “vo#4” (fpH(s)1[MHz])

/ fpL(s)1

(4)Decrease the input signal frequency, measure the input signal

frequency at which the output amplitude at pin 4 turn to be -

3[dB] against “vo#4” (fpL(s)1[MHz])

S9

Demodulation band

width of the FM

demodulator

/ fpH(s)2

SIF-Freq. : 5.5M

AUDIO ATT : 127

Others : Preset

(1)Input a signal that 5.5[MHz], 100[dB V], 50[kHz] deviated by

400[Hz] sine wave at pin 56.

(2)Measure the amplitude at pin 4(vo#4 [Vp-p]).

(3)Increase the input signal frequency, measure the input signal

frequency at which the output amplitude at pin 4 turn to be -

3[dB] against “vo#4” (fpH(s)2[MHz])

/ fpL(s)2

(4)Decrease the input signal frequency, measure the input signal

frequency at which the output amplitude at pin 4 turn to be -

3[dB] against “vo#4” (fpL(s)2[MHz])

S10

Audio attenuater gain AUDIO-SW : 1

(1) Input a 400[Hz], 927[mVrms] sine wave at pin 53.

(2) Set the “AUDIO ATT” data to “127”.

(3) Measure the amplitude at pin 4 (v#4max[mVrms]).

(4) G att max[dB] = 20log(v#4max/927)

/ G att max

/ G att mid

/ G att min

AUDIO ATT :

0/64/127

Others : Preset

(5) Set the “AUDIO ATT” data to “64”.

(6) Measure the amplitude at pin 4 (v#4mid[mVrms]).

(7) G att mid[dB] = 20log(v#4mid/927)

(8) Set the “AUDIO ATT” data to “0”.

(9) Measure the amplitude at pin 4 (v#4min[mVrms]).

(10) G att min[dB] = 20log(v#4min/927)

S11

Audio attenuater off- AUDIO-SW : 1

(1) Connect pin 53 to GND through a 4.7[ F] capacitor.

(2) Set the “AUDIO ATT” data to “127”.

(3) Measure the DC voltage at pin 4 (V#4max[mV]).

(4) Set the “AUDIO ATT” data to “0”.

set

/ Vos att

AUDIO ATT :

0/127

Other : Preset

(5) Measure the DC voltage at pin 4 (V#4min[mV]).

(6) Vos[mV] = V#4min-V#4max

00/01/28 35

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditions

Measurement methods

S12

Audio switch cross- SIF-Freq. : 5.5M

(1) Input a signal that 5.5[MHz], 100[dB V], 50[kHz] deviated by

1[kHz] sine wave at pin 56.

(2) Connect pin 53 to GND through a 4.7[ F] capacitor.

(3) Measure level of the 1[kHz] at pin 4 (v#4T1[dB V]).

(4) Set the bit of “AUDIO-SW” to “1”.

talk

AUDIO-SW : 0/1

AUDIO ATT : 127

Other : Preset

/ CT(s)T-E

/ CT(s)E-T

(5) Measure level of the 1[kHz] at pin 4 (v#4E1[dB V]).

(6) CT(s)T-E[dB] = v#4E1-v#4T1

(7) Input a 5.5[MHz], 100[dB V] signal at pin 56.

(8) Measure level of the 1[kHz] at pin 4 (v#4E2[dB V]).

(9) Input a 1[kHz], 927[mVrms] signal at pin 53.

(10) Set the bit of “AUDIO-SW” to “0”.

(11) Measure level of the 1[kHz] at pin 4 (v#4T2[dB V]).

(12) CT(s)E-T[dB] = v#4T2-v#4E2

S13

Audio switch off-set

/ Vos sw

SIF-Freq. : 5.5M

AUDIO-SW : 0/1

AUDIO ATT : 127

Other : Preset

(1) Input a 5.5[MHz], 100[dB V] signal at pin 56.

(2) Connect pin 53 to GND through a 4.7[ F] capacitor.

(3) Set the bit of “AUDIO-SW” to “0”.

(4) Measure the voltage at pin 4 (V#4T[V]).

(5) Set the bit of “AUDIO-SW” to “1”.

(6) Measure the voltage at pin 4 (V#E[V]).

(7) Vos sw[V] = V#4E-V#4T

00/01/28 36

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

VIDEO stage (RGB Mute:0 / R cut off:127 / DC rest.:10)

Note Items/Symbols

Bus conditoins

Measurement methods

V1

Video SW:00/01

Others:Preset

(1)Input a white signal with sync into Pin46(EXT IN)&48(TV IN).

(2)Increasing the input amplitude, measure the amplitude(include

sync) at

which the Pin41(MON OUT) output is clipped, that is

"DR_TV"(Video SW:00) / "DR_EXT"(Video SW:01).

TV Input Dynamic

Range

/ DR_TV

External Input

Dynamic Range

/ DR_EXT

V2

V3

Video SW:00/01 (1)Input a 1Vp-p, white signal with sync into Pin46(EXT

TV Mode Gain

/ G_TV

Ext. Mode Gain

/ G_EXT

Others:Preset

IN)&48(TV IN).

(2)Set Video SW to 00 and measure the gain between PIN48 and

Pin41(MON OUT), that is "G_TV".

(3)Set Video SW to 01 and measure the gain between Pin46 and

Pin41, that is "G_EXT".

AV SW Cross-Talk

/ CT_SWTE

/ CT_SWET

Video SW:00/01 (1)Input a PAL red signal with sync into Pin48(TV IN) and

Others:Preset

connect Pin46(EXT IN) to GND via a 1uF capacitor.

(2)Set Video SW 01, measure the amplitude of 4.43MHz signal at

Pin41 and calculate the cross-talk, that is "CT_SWTE".

(3)Input a PAL red signal with sync into Pin46 and connect Pin48

to GND via a 1uF capacitor.

(4)Set Video SW 00, measure the the amplitude of 4.43MHz

signal at Pin41 and calculate the cross-talk, that is "CT_SWET".

(1)Input a white signal with sync into Pin38&39.

(2)Increasing the Pin39 input amplitude, measure the amplitude

(includesync) at which the Pin20 output is clipped, that is

"DR_Y".

V4

Y Input Dynamic

Range

/ DR_Y

WPS:1

Uni-Color:63

Brightness:0

Color:0

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

RGB Mute:0

R cut off:63

DC rest.:10

Uni-Color:127

Sharpness:Adjust

Color:0

V5

V6

Y Input Pedestal

Clamp Voltage

/ V_YCLP

(1)Input a composite sync signal into Pin38.

(2)Connect Pin39 to GND via a 1uF capacitor.

(3)Measure the DC Voltage at Pin39, that is "V_YCLP".

Y Frequency

Response

/ FR_Y

(1)Input a 0.5Vp-p sweep signal with sync into Pin38&39.

(2)Adjust Sharpness so that the output amplitude for FSHP

equals V_SH100k

.

(3)Measure the frequency at which the output amplitude is 3dB

down

against V_SH100k, which is "FR_Y".

Others:Preset

Uni-Color:127

Color:0

Y DL:000/001/111

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

V7

Y Delay Time

/ t_YDEL

/ •t_YDEL-40

/ •t_YDEL+240

/ •t_YDEL

(1)Input a 2T pulse with sync into Pin38&39.

(2)Set the BUS data so that Y DL is 0ns(001).Observe the Pin20

output, measure the delay time between Pin39 and Pin20, that

is "t_YDEL".

(3)Set the BUS data so that Y DL is –40ns(000). Observe the

Pin20 output, measure the delay time between Pin39 and

Pin20, that is t_YDEL-40

.

(4) Set the BUS data so that Y DL is +240ns(111). Observe the

Pin20 output, measure the delay time between Pin39 and

Pin20, that is t_YDEL+240

(5)Calculate, “•t_YDEL-40”= t_YDEL-40- "t_YDEL

“•t_YDEL+240”= t_YDEL+240- "t_YDEL

.

"

“•t_YDEL”= (“•t_YDEL+240”- “•t_YDEL-40”)/7

V8

Brightness:

0/64/127

Color:0

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

(1)Input a 0IRE black signal with sync into Pin38&39.

(2)Measure the DC level of picture period at Pin20 for

Brightness:127/64/0,

that is "V_BRTMAX" / "V_BRTCEN" / "V_BRTMIN".

(3)Calculate;"•V_BRT"=(V_BRTMAX-V_BRTMIN)/127

Brightness

Characteristics

/ V_BRTMAX

/ V_BRTCEN

/ V_BRTMIN

Brightness Data

Sensitivity

/ •V_BRT

00/01/28 37

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

V9

Uni-Color

Uni-

(1)Input a 50IRE white signal with sync into Pin38&39.

Characteristics for Y

/ G_UCYMAX

/ G_UCYCEN

Color:0/64/127

Color:0

(2)Measure the output picture amplitude at Pin20 for Uni-

Color:127/64/0, that is V_UCYMAX/ V_UCYCEN/ V_UCYMIN

(3)Calculate; "G_UCYMAX"=20*log(V_UCYMAX/0.357)"

"G_UCYCEN"=20*log(V_UCYCEN/0.357)

.

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

Sub-Contrast:

0/8/15

/ G_UCYMIN

"G_UCYMIN"=20*log(V_UCYMIN/0.357)

V10

Sub-Contrast

Characteristics

/ G_SCONMAX

(1)Input a 50IRE white signal with sync into Pin38&39.

(2)Measure the output picture amplitude at Pin20 for Sub-

Contrast 15/8/0,

Uni-Color:127

Color:0

/ G_SCONMIN

that is VSCONMAX / VSCONCEN / VSCONMIN.

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

(3)Calculate; "G_SCONMAX"=20*log(V_SCONMAX/V_SCONCEN

)

"G_SCONMIN"=20*log(V_SCONMIN/V_SCONCEN

)

V11

V12

Sharpness

Frequency

/ F_SHP

Peaking Sharpness:63

Uni-Color:127

Color:0

(1)Input a 0.5Vp-p sweep signal with sync into Pin38&39.

(2)Measure the frequency at which the Pin20 output amplitude is

Max., that is "F_SHP".

RGB Mute:0

R cut off:63

DC

rest.:10

Others:Preset

Sharpness

Characteristics

/ GSHMAX

/ GSHCEN

/ GSHMIN

Control Sharpness:0/32/6

(1)Input a 0.5Vp-p sweep signal with sync into Pin38&39.

3

Uni-Color:127 (2)Measure the output picture amplitude for 100kHz at Pin20, that

Color:0

is V_SH100k.

RGB Mute:0

R cut off:63

DC

(3)Measure the output picture amplitude for FSHP when

Sharpness is max.,center and min., that is V_SHMAX, V_SHCENand

rest.:10 V_SHMIN.

Others:Preset

(4)Calculate; "G_SHMAX"=20*log(V_SHMAX/V_SH100k

"G_SHCEN"=20*log(V_SHCEN/V_SH100k

"G_SHMIN"=20*log(V_SHMIN/V_SH100k

)

V13

Uni-Color:127

Color:0

(1)Input a gray raster with sync to Pin38&39.

(2)Set BUS data so that •point is 90IRE.

(3)Increasing a video amplitude of input from 50IRE, measure a

video ampitude as the figure below, that is “V_Y

(4)Set BUS data so that • point is 80IRE.And repeat (3), that is

Y • correction start

point

RGB Mute:0

R cut off:63

DC rest.:10

•point:01/10/11

Others:Preset

/ V

Y_•70

”

_•90

/ V

Y_•80

/ V

Y_•90

“V_{Y 80}”.

•

(5)Set BUS data so that • point is 70IRE.And repeat (3), that is

“V_{Y 70}”.

•

Y •correction curve

(6)From the measurement in the above, find gain of the portion

/ G_Y

that the •correction has an effect on.

•

#20

output

Y

ƒÁ=off

Y

ƒÁ=90/80/70IRE

V_YƒÁ90

#39 input

00/01/28 38

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

V14

Black Expansion Start Uni-Color:127

(1)Input a gray raster with sync to Pin38&39.

(2)Set black stretch to 25IRE.

Point

Color:0

/ V_BLEX25

/ V_BLEX35

/ V_BLEX45

Black

stretch:00/01

/10/11

(3)Decreasing Y amplitude of input from 50IRE, measure a Y

amplitude as the figure below, that is “V_BLEX25

(4)Set black stretch to 35IRE/45IRE.

”

RGB Mute:0

(5)Repeat (3), that is ‘V_BLEX35”, “V_BLEX45”. below, that is “V_Y

”

_•90

Black Expansion AMP R cut off:63

(6)Find gain of the portion that the black stretch has an effect on.

#20

Gain

DC rest.:10

output

/ G_BLEX

Others:Preset

Black

stretch

25/35/45IRE

=off

V_BLEX25

#39 input

V16

DC Restration Gain

/ V_Dcrest120

Uni-Color:127

Color:0

(1)Input a 100IRE signal with sync into Pin38&39.

(2)Set DC rest. to 10.

/ V_Dcrest90

/ V_{Dcrest step}

Black

stretch:00/01

/10/11

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

Uni-Color:127

Brightness:127

Color:0

(3)Measure a Y amplitude of pin20 output, that is V100.

(4)Set DC rest to 00.

(5)Measure a Y amplitude of pin20 output, that is V120.

(6)Calculate, “V_dcrest120” =(V120/V100)×100

(7)Set DC rest to 11.

(8)Repeat (5)&(6), that is “V_Dcrest90”.

(9)Calculate, “V_{Dcrest step}”=(V_dcrest120- V_Dcrest90)/4

(1)Input a 120IRE ramp signal with sync into Pin38&39.

(2)Measure the amplitude from cut-off level to peak(at which

output signal is clipped), that is "V_WPS".

V17

V18

V19

WPS Level

/ V_WPS

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

C-Trap:0/1

Uni-Color:127

Color:0

Chroma Trap Gain

/ G_TRAP

(1)Input a 0.5Vp-p, 3.58MHz signal with sync into Pin43&39.

(2)Measure the 3.58MHz amplitude at PIn20 for Chroma

Trap:1/0, that is V_TRAPON/ V_TRAPOFF

.

RGB Mute:0

R cut off:63

(3)Calculate;"G_TRAP"=20*log(V_TRAPON/V_TRAPOFF

)

DC

rest.:10

Others:Preset

Half

Tone Ysm Mode:0

(1)Input a 100IRE white signal with sync into Pin38&39.

Characteristics for Y

/ G_HTY

Uni-Color:127

Color:0

(2)Measure the output picture amplitude at PIn20 , that is

V_HTYOFF

.

RGB Mute:0

R cut off:63

DC rest.:10

Others:Preset

(3)Suppry Pin15 2V.

(4) Measure the output picture amplitude at PIn20 , that is V_HTYON

.

(3)Calculate;"G_HTY"=20*log(V_HTYON/V_HTYOFF

)

00/01/28 39

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

CHROMA STAGE (RGB Mute:0 / RGB cut off:63 / DC rest.:10)

Note Items/Symbols

Bus conditoins

Measurement methods

C1

ACC Characteristics

/ V_ACCH

/ V_ACCL

RGB Mute:0

Y Mute:1

Uni-Color:127

Others:Preset

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Changing the amplitude of burst and chroma, measure the input

amplitude at which Pin20 output amplitude is +1dB/-1dB against

the one for 300mVp-p input, that is "V_ACCH"/"V_ACCL".

(1)Set “C-BPF” to 1, “Color System” to 010, “TEST Mode” to

00001000, and Sub address “0A” is X0011XXX.

(2)Input a sweep signal into Pin43.

(3)Observe the frequency response at Pin13 and measure the

Peaking Frequency / Q of chroma filter, that is "F_0T443" / "Q_T443".

(4)Set C-BPF to 0 and Color System to 010 and repeat (2)&(3),

that is "F_0B443" / "Q_B443".

C2

RGB Mute:0

Y Mute:1

TEST:01000111

C-BPF:0/1

Color System:

010/100

TEST Mode:

00001000

TOF Characteristics

(4.43MHz)

/ F_0T443

/ Q_T443

BPF Characteristics

(4.43MHz)

/ F_0B443

(5)Set C-BPF to 1 and Color System to 100 and repeat (2)&(3),

that is "F_0T358" / "Q_T358".

(6)Set C-BPF to 0 and Color System to 100 and repeat (2)&(3),

that is "F_0B358" / "Q_B358".

Sub Add.”0A”:

X0011XXX

Others:Preset

/ Q_B443

TOF Characteristics

(3.58MHz)

/ F_0T358

/ Q_T358

BPF Characteristics

(3.58MHz)

/ F_0B358

/ Q_B358

C3

C4

RGB Mute:0

Y Mute:1

Uni-Color:127

Others:Preset

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Observe the Pin20 output, measure the delay time between

Pin43 and Pin20, that is "t_CDEL".

C Delay Time

/ t_CDEL

Delay Time

Difference between

Y/C

/ •t_Y/C

Color Characteristics

/ G_COLMAX

(3)Calculate;"•t_Y/C"=t_YDEL-t_CDEL

RGB Mute:0

Color:0/64/127

Y Mute:1

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Measure the Pin20 amplitude for Color 127/64/0, that is V_COLMAX

/ G_COLMIN

Uni-Color:127

Others:Preset

/ V_COLCEN/ V_COLMIN

(3)Calculate; "G_COLMAX"=20*log(V_COLMAX/V_COLCEN

"G_COLMIN"=20*log(V_COLMIN/V_COLCEN

.

)

C5

C6

Uni-Color

Characteristics for C

/ G_UCC

RGB Mute:0

Uni-Color:0/127

Y Mute:1

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Measure the Pin20 amplitude for Uni-Color 127/0, that is

Others:Preset

V

_UCCMAX, and V_UCCMIN

.

(3)Calculate;"G_UCC"=20*log(V_UCCMIN/V_UCCMAX

)

RGB Mute:0

Tint:0/64/127

Y Mute:1

Uni-Color:127

Others:Preset

(1)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Set Tint to 64 and adjust the burst phase so that the 6th bar of

Tint Characteristics

(3.58MHz)

/ ••_358MAX

/ ••_358MIN

Tint Characteristics

(4.43MHz)

Pin20 output is maximum, that is •_358CEN

(3)Change Tint to 127/0 and adjust the burst phase so that the 6th

bar of Pin20 output is maximum, that is •_358MAX/•_358MIN

(4)Calculate; "••_358MAX"=-(•_358MAX-•_358CEN

"••_358MIN"=-(•_358MIN-•_358CEN

.

)

/ ••_443MAX

)

(5)Input a 4.43MHz NTSC rainbow color-bar (286mVp-p,

/ ••_443MIN

burst:chroma=1:1) with sync into Pin43 and repeat (2)&(3), that is

•

_443CEN/•_443MAX/•_443MIN

(7)Calculate; "••_443MAX"=-(•_443MAX-•_443CEN

"••_443MIN"=-(•_443MIN-•_443CEN

.

)

00/01/28 40

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

C7

Relative Amplitude

(PAL)

/ V_PR/B

RGB Mute:0

Y Mute:1

Uni-Color:127

Others:Preset

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Measure the amplitude of Pin18/19/20 output, that is

"VPROUT"/ "VPGOUT" / "VPBOUT"

/ V_PG/B

Relative Amplitude

(NTSC1)

(3)Calculate; " V_PR/B"=VPROUT/VPBOUT

" V_PG/B"=VPGOUT/VPBOUT

/ V_N1R/B

/ V_N1G/B

Relative Amplitude

(NTSC2)

/ V_N2R/B

(4)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(5)Set NTSC Phase to NTSC1/NTSC2.

(6)Repeat (2)&(3), that is “V_N1R/B”/” V_N1G/B”/” V_N2R/B”/” V_{N G/B}”.

2

/ V_N2G/B

Relative Amplitude

(DVD)

/ V_DR/B

/ V_DG/B

C8

RGB Mute:0

Y Mute:01

Uni-Color:127

NTSC Phase:

00/01/10

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Observe the Pin18/19/20 output, measure the R/G/B modulation

angle (•_PR/•_PG/•_PB) accoeding following figure and equality.

For •_PR; Peak:3rd bar, •_0R=90

For •_PG; Peak(nagative):4th bar, •_0G=240

For •_PB; Peak:6th bar, •_0B=0

Relative Phase (PAL)

/ •_PR-B

/ •_PG-B

Relative Phase

(NTSC1)

/ •_N1R-B

Others:Preset

/ •_N1G-B

Calculate; "•_PR-_B"=•_PR-•_PB

Relative Phase

(NTSC2)

/ •_N2R-B

"•_PG-B"=•_PG-•_PB

(4)Set NTSC Phase 00(NTSC1).

(5)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,

burst:chroma=1:1) with sync into Pin38&43, then repeat (2), that is

_N1R/•_N1G/•_N1B.

(6)Calculate; "•_N1R-B"=•_N1R-•_N1B

"•_N1G-B"=•_N1G-•_N1B

(7)Set NTSC Phase 01(NTSC2).

(8) Repeat (5), that is •_N2R/•_N2G/•_N2B

(9)Calculate; "•_N2R-B"=•_N2R-•_N2B

"•_N1G-B"=•_N1G-•_N1B

/ •_N2G-B

•

Relative Phase (DVD)

/ •_DR-B

/ •_DG-B

.

(10)Set NTSC Phase 10(DVD).

C9

RGB Mute:0

Color System:

100/010

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Set Color System to 100(443PAL).

(3)For higher frequency than 4.43MHz, measure the burst

frequency at which Pin13 DC level changes from low to high / from

APC Pull-in Range

(4.43MHz)

/ •F_4APCP+

Others:Preset

/ •F_4APCP-

APC Hold Range

(4.43MHz)

/ •F_4APCH+

high to low, that is F_4APCP+/ F_4APCH+

(4)For lower frequency than 4.43MHz, repeat (2), that is F_4APCP-

F_4APCH-

(5)Calculate; "•F_4APCP+"=F_4APCP+-4433619

"•F_4APCP-"=4433619-F_4APCP-

"•F_4APCH+"=F_4APCH+-4433619

"•F_4APCH-"=4433619-F_4APCH-

(6)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(7)Set Color System to 010(358NTSC).

.

/

.

/ •F_4APCH-

APC Pull-in Range

(3.58MHz)

/ •F_3APCP+

/ •F_3APCP-

APC Hold Range

(3.58MHz)

/ •F_3APCH+

(8)For higher frequency than 3.58MHz, repeat (2), that is F_3APCP+

F_3APCH+

(9)For lower frequency than 3.58MHz, repeat (2), that is F_3APCP-

F_3APCH-

/

.

/

/ •F_3APCH-

.

(10)Calculate; "•F_3APCP+"=F_3APCP+-3579545

"•F_3APCP-"=3579545-F_3APCP-

"•F_3APCH+"=F_3APCH+-3579545

"•F_3APCH-"=3579545-F_3APCH-

00/01/28 41

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

RGB Mute:0

Measurement methods

(1)Connect Pin43 to GND via a 1uF capacitor.

C10

APC Control

Sensitivity (4.43MHz)

/ •₄₄₃

Color

System: (2)Set Color System to 100(443PAL).

(3)Adjust Pin11 voltage so that the Pin13 output frequency is

4.433619MHz, that is V_4APCCEN

(4)Measure the Pin13 output frequency when Pin11 voltage is

_4APCCEN+100mV / V_4APCCEN-100mV, that is F_4APC+ / F_4APC-

100/010

Others:Preset

.

APC Control

Sensitivity (3.58MHz)

/ •₃₅₈

V

.

(5)Calculate; "•₄₄₃"=(F_4APC+-F_4APC-)/200

(6)Set Color System to 010(358NTSC).

(7)Adjust Pin11 voltage so that the Pin13 output frequency is

3.579545MHz, that is V_3APCCEN

(8)Measure the Pin13 output frequency when Pin11 voltage is

_3APCCEN+100mV / V_3APCCEN-100mV, that is F_3APC+/ F_3APC-

.

V

.

(9)Calculate; "•₃₅₈"=(F_3APC+-F_3APC-)/200

C11

P/N ID Sens:0/1

Color System:

100/010

(1)Set P/N ID Sens. to 0.

PAL ID Sensitivity

(Normal Mode)

/ V_PALIDON

/ V_PALIDOFF

PAL ID Sensitivity

(Low Mode)

(2)Set Color System to 100(443PAL).

(3)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(4)Measure the burst amplitude at which Pin13 DC level changes

from low to high / from high to low, that is "V_PALIDON" / "V_PALIDOFF".

(5)Set Color System to 010(358NTSC).

Y Mute:01

Uni-Color:127

RGB Mute:0

Others:Preset

(6)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,

burst:chroma=1:1) with sync into Pin38&43, and repeat (3), that is

"V_NTIDON" / "V_NTIDOFF".

(7)Set P/N ID Sens.to 1, repeat (2) ~ (6), that is "V_PALIDLON" ,

"V_PALIDLOFF" , "V_NTIDLON" and "V_NTIDLOFF".

/ V_PALIDLON

/ V_PALIDLOFF

NTSC ID Sensitivity

(Normal Mode)

/ V_NTIDON

/ V_NTIDOFF

NTSC ID Sensitivity

(Low Mode)

/ V_NTIDLON

/ V_NTIDLOFF

C12

C13

fsc Continuous Wave RGB Mute:00

Measure the amplitude of Pin20 output, that is "V_CW".

Output Level

/ V_CW

Others:Preset

Half Tone

Characteristics for C

/ G_HTC

RGB Mute:0

Ysm Mode:0

Y Mute:01

(1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,

burst:chroma=1:1) with sync into Pin38&43.

(2)Supply Pin15 2V and measure the amplitude of Pin20 output,

Uni-Color:127

Others:Preset

RGB Mute:00

Y Mute:01

Uni-Color:127

Sub-Color:0

/16/32

that is V_PBHTC

(3)Calculate;"G_HTC"=20*log(V_PBHTC/V_PBOUT

1)Input a signal(f0=100kHz,300mV) of following figure into

Pin38,44&45.

(2)Measure the Pin20 amplitude for Sub-olor 32/16/0, that is

.

)

C14

Sub-Color Control

Characteristics

/ •_SCOLMAX

V_SCMAX/ V_SCLCEN/V_SCMIN

.

/ •_SCOLMIN

(3)Calculate; "•_SCOLMAX"=20*log(V_SCMAX/ V_SCLCEN

)

Others:Preset

"•_SCOLMIN"=20*log(V_SCMIN/ V_SCLCEN

)

Sinusoidal wave

Frequency f₀

Amplitude V₀

pin38 input

pin16 input

00/01/28 42

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

SECAM STAGE

Note Items/Symbols

Bus conditoins

Measurement methods

SE1

Bell Monitor output RGB Mute:0

(1)Input a 75% color bar signal (200mVp-p at R ID) into Pin43.

(2)Set BUS data so that “

(3)TEST Mode” is 00001000 and Sub address “0A” is X0111XXX.

(3) Measure R-Y ID amplitude at Pin13, that is "ebmo".

voltage

/ embo

TEST Mode:

00001000

Sub Add.”1A”:

X0111XXX

Others:Preset

SE2

Bell filter f0

/ f_0B-C

RGB Mute:00

TEST Mode:

00001000

Sub Add.”0A”:

X0111XXX

Bell f0:0

(1) Input a 20mVp-p sine wave whose frequency is sweep into

Pin43.

(2) Set BUS data so that “TEST Mode” is 00001000 and Sub

address “0A” is X0111XXX.

(3) Measure the frequency at which Pin13 output is the biggest,

that is "f_0BEL" .

Y Mute:1

(4)Calculate : "f_0B-C"=f_0BEL-4,286 [kHz].

Others:Preset

SE3

SE4

Bell filter f0 variable RGB Mute:00

(1)Input a 20mVp-p sine wave whose frequency is sweep into

Pin43.

(2)Set BUS data so that “TEST Mode” is 00001000 and Sub

address “0A” is X0111XXX.

(3)Set BUS data so that “Bell f0” is +35kHz.

(4) Measure the frequency at which Pin 13 output is the biggest,

range

/ f_0B-VR

TEST Mode:

00001000

Sub Add.”0A”:

X0111XXX

Bell f0:1

Y Mute:1

that is f_0BELH.

Others:Preset

RGB Mute:00

TEST Mode:

00001000

(5) Calculate : " f_0B-VR"= f_0BELH-4,286 [kHz]

(1)Input a 20mVp-p sine wave whose frequency is sweep into

Pin43.

(2)Set BUS data so that “TEST Mode” is 00001000 and Sub

address “0A” is X0111XXX.

Bell filter Q

/ Q_BEL

Sub Add.”0A”:

X0111XXX

Y Mute:1

(4) Observe the frequency response of Pin13 output.

(5) Calculate : "QBEL = (MAX-3dB Band Width)/f0BEL.

Others:Preset

SE5

SE6

Color

output amplitude

/ VBS

/ VRS

Color

difference RGB Mute:00

(1)Input a 75% color bar(200mVp-p at R ID) into Pin43.

(2) Measure the R-Y output amplitude at Pin20, that is "VRS".

(3) Measure the B-Y output amplitude at Pin22, that is "VBS".

Uni-Color:63

Y Mute:1

Others:preset

Difference

(1)Calculate : "R/B-S"=VRS/VBS

Relative Amplitude

/ R/B-S

SE8

Color Difference S/N RGB Mute:00

(1)Input a 200mVp-p non-modulated chroma signal into Pin43.

(2) Measure the amplitude of noise on Pin20, that is nR.

(3) Measure the amplitude of noise on Pin22, that is nB.

(4) Calculate : "SNB-S"=20log(2•2VBS/nB)

Ratio

/ SNB-S

/ SBR-S

Uni-Color:63

Y Mute:1

Others:preset

"SNR-S"=20log(2•2VRS/nR)

00/01/28 43

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

SE9

Linearity

/ LinB

/ LinR

RGB Mute:00

Uni-Color:63

Y Mute:1

(1)Input a 75% color bar(200mVp-p at R ID) into Pin43.

(2)Set BUS data so that “S black monitor” is “alignment”.

(2) Measure the amplitude between Black and Cyan/Red, that is

VCyan/VRed.

Others:preset

(3) Measure the amplitude between Black and Yellow/Blue, that is

VYellow/VBlue.

(4) Calculate : "LinR"=VCync/VRed

"LinB"=VYellow/VBlue

red

LinR

cyan

blue

LinB

yellow

SE10 Rising-Fall Time

RGB Mute:00

Uni-Color:63

Y Mute:1

(1)Input a 75% color bar(200mVp-p at R ID) into Pin43.

(2)Set BUS data so that “S black monitor” is “alignment”.

(3)Measure the rising time(from 10% to 90%) between Green and

Magenta at Pin 20/Pin 22, that is "trR"/"trB".

Magenta

/ trfB

/ trfR

Others:preset

trB•CtrR

Green

10%

90%

SE11 SECAM ID Sensitivity RGB Mute:00

(1)Input a 75% color bar(200mVp-p at R ID) into Pin43.

(2)Set BUS data so that “S ID Sens” is Normal, “S ID Mode” is H.

(3)Measure the burst amplitude at which Pin13 DC level changes

from low to high / from high to low, that is "V_SIDHON" / "V_SIDHOFF".

(4)Set BUS data so that “S ID Mode” is H+V.

(Normal Mode)

/ V_SIDHON

Y Mute:1

S ID Sens:0/1

S ID Mode:0/1

Color

/ V_SIDHOFF

/ V_SIDHVON

/ V_SIDHVOFF

System:101

(5)Repeat (3), that is "V_SIDHVON" / "V_SIDHVOFF".

SECAM ID Sensitivity Others:Preset

(Low Mode)

/ V_SIDLHON

(6)Set BUS data so that “S ID Sens” is Low, “S ID Mode” is H.

(7)Repeat (3), that is "V_SIDLHON" / "V_SIDLHOFF".

(8)Set BUS data so that “S ID Mode” is H+V.

/ V_SIDLHOFF

/ V_SIDLHVON

(9)Repeat (3), that is "V_SIDLHVON" / "V_SIDLHVOFF".

/ V_SIDLHVOFF

SE12 Gate Pulse Width RGB Mute:00

(1)Input a 75% color bar(200mVp-p at R ID) into Pin43.

(2)Set BUS data so that “TEST Mode” is 00001000 , Sub address

“0A” is X1001XXX , and“Color System” is Fixed SECAM.

(3)Measure the gate pulse widths when BUS data of “SECAM GP

Phase” is +200ns / normal / -200ns, those are “WGP₊₂₀₀”,

“WGP” and “WGP_-200”.

Variable Range

/ WGP₊₂₀₀

/ WGP

TEST Mode:

00001000

Sub Add.”0A”:

X1001XXX

Color

/ WGP_-200

System:101

Others:Preset

RGB Mute:00

Color

System:101

S black Monitor:1

S B-Y black Adj.:

0/15

S13

SECAM black

adjustment

characteristic

/ V_SBMAX

/ V_SRMAX

/ V_SRMIN

(1)For B-Y/R-Y Black Adj.:8, measure the DC level of picture period

at Pin22/20, that is V

/ V .

SBCEN

SRCEN

(3)For B-Y Black Adj.:0/15, measure the DC level change of picture

period against V at Pin22, that is "V " / "V ".

SBCEN SBMIN SBMAX

(4)For R-Y Black Adj.:0/15, measure the DC level change of picture

period against V

at Pin20, that is "V

" / "V ".

SRCEN

SRMIN SRMAX

/ V_SRMIN

SECAM black

S R-Y black Adj.:

0/15

(5)Calculate;

"•V

"=(V

-V

)/16

adjustment sensitivity Others:Preset

SECB

SECR

SBMAX SBMIN

/•V_SB

-V

)/16

SECRMAX SECRMIN

/•V_SR

00/01/28 44

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

TEXT STAGE(RGB Mute:0 / RGB cut off:63 / DC rest.:10)

Note Items/Symbols

Bus conditoins

Measurement methods

T1

V-BLK Pulse Output

Level

/ V_VBLK

All:Preset

(1)Input a cmposite sync signal into Pin38.

(2)Measure the DC level of V/H blanking period at Pin20, that is

"V_VBLK" / "V_HBLK".

H-BLK Pulse Output

Level

/ V_HBLK

T2

T3

RGB Output Black RGB Mute:0

(1)Input a 0IRE Y signal with sync into Pin38&39.

(2)Measure the DC level of picture period at Pin20, that is "V_BLACK".

Level (0IRE DC)

/ V_BLACK

Color:0

R cut off:63

DC rest.:10

Others:Preset

RGB Mute:0

R cut off:63

DC rest.:10

Uni-Color:127

Color:0

RGB Output White

Level(100 IRE AC)

/ V_WHITE

(1)Input a 100IRE Y signal with sync into Pin38&39.

(2)Measure the amplitude from 0 to 100IRE at Pin20, that is

"V_WHITE".

Others:Preset

RGB Mute:0

DC rest.:10

B Cut Off:0/255 off:255/0 , that is

Color:0

T4

T5

Cut-off Voltage

Variable Range

/ •V_CUT+

(1)Input a 0IRE Y signal with sync into Pin38&39.

(2)Measure the DC level of picture period at Pin22 for B Cut-

V_CUTMAX/ V_CUTMIN.

/ •V_CUT-

Others:Preset

(3)Calculate; "•V_CUT+"=V_CUTMAX-V_BLACK"•V_CUT-"=V_CUTMIN-V_BLACK

(1)Input a 100IRE Y signal with sync into Pin38&39.

(2)Measure the amplitude from 0 to 100IRE at Pin20 for B

drive127/0, that is

Drive Control Variable RGB Mute:0

Range

/ G_DR+

/ G_DR-

DC rest:10

B Drive:0/127

Uni-Color:127

Color:0

Others:Preset

RGB Mute:0

R cut off:63

DC rest.:10

ABL Gain:11

Uni-Color:127

Color:0

V

(1)

_DRMAX/ V_DRMIN

Calculate; "G_DR+"=20*log(V_DRMAX/V_WHITE

"G_DR-"=20*log(V_DRMIN/V_WHITE

.

)

T6

T7

ABCL Contorol

Voltage Range

/ V_ABCLH

/ V_ABCLL

ACL Gain

(1)Input a 100IRE Y signal with sync into Pin38&39.

(2)Decreasing the Pin28 voltage, measure the voltage at which

Pin20 output

begins/stops decreasing, that is "V_ABCLH" / "V_ABCLL".

(3)Measure the minimum amplitude of Pin20 output, that is V_ACLMIN

.

(4)Calculate; "G_ACL"=20*log(V_ACLMIN/V_WHITE

)

/ G_ACL

Others:Preset

ABL Start Point

/ V_ABLP0

/ V_ABLP1

/ V_ABLP2

/ V_ABLP3

RGB Mute:0

R cut off:63

DC rest.:10

ABL Start Point:

00/01/10/11

ABL Gain:11

Uni-Color:127

Color:0

(1)Input a 0IRE Y signal with sync into Pin38&39.

(2)For ABL Point 00/01/10/11, decreasing the Pin28 voltage,

measure the

voltage at which Pin20 output begins decreasing, that is

V_ABL1/V_ABL2/V_ABL3/V_ABL4.

(3)Calculate; "V_ABLP0"=V_ABL1-V_ABCLH

"V_ABLP1"=V_ABL2-V_ABCLH

"V_ABLP2"=V_ABL3-V_ABCLH

Others:Preset

RGB Mute:0

R cut off:63

DC rest.:10

ABL Gain:

00/01/10/11

Uni-Color:127

Color:0

"V_ABLP3"=V_ABL4-V_ABCLH

T8

ABL Gain

/ V_ABLG0

/ V_ABLG1

/ V_ABLG2

/ V_ABLG3

(1)Input a 0IRE Y signal with sync into Pin38&39.

(2)For ABL Gain 00/01/10/11, measure the DC level of picture

period at

Pin20

when

Pin28

voltage

is

V_ABCLL

,

that

is

V

_ABL5/V_ABL6/V_ABL7/V_ABL8.

(3)Calculate; "V_ABLG0"=V_ABL5-V_BLACK

"V_ABLG1"=V_ABL6-V_BLACK

Others:Preset

"V_ABLG2"=V_ABL7-V_BLACK

"V_ABLG3"=V_ABL8-V_BLACK

00/01/28 45

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

T9

Analog RGB Dynamic RGB Mute:0

(1)Input a composite sync signal into Pin38.

(2)Supply 2V to Pin15.

(3)Input a signal of following figure into Pin16.

Range

/ DR_TX

R cut off:63

DC rest.:10

RGB Contrast:32 (4)Increasing the amplitude of Pin16 input, measure the amplitude

Ysm Mode:1

at which

Others:Preset

the Pin20 amplitude stops increasing, that is "DR_TX".

Sinusoidal wave

Frequency f₀

Amplitude V₀

pin38 input

pin16 input

T10

Analog RGB Contrast RGB Mute:0

Control Characteristic R cut off:63

(1)Input a cmposite sync signal into Pin38.

(2)Supply 2V to Pin15.

/ G_TXCMAX

/ G_TXCCEN

/ G_TXCMIN

DC rest.:10

Ysm Mode:1

RGB Contrast:

0/32/63

(3)Input a signal of NOTE:T9 figure(f0=100kHz,V0=0.2Vp-p) into

Pin16.

(4)For RGB Contrast 63/32/0, measure the amplitude of Pin20

output, that is

Others:Preset

V_TXCMAX/ V_TXCCEN/ V_TXCMIN.

(5)Calculate; "G_TXCMAX"=20*log(V_TXCMAX/0.2)

"G_TXCCEN"=20*log(V_TXCCEN/0.2)

"G_TXCMIN"=20*log(V_TXCMIN/0.2)

T11

Analog

RGB RGB Mute:0

Control R cut off:63

DC rest.:10

(1)Supply 2V to Pin15.

Brightness

Characteristic

/ V_TXBRMAX

/ V_TXBRCEN

/ V_TXBRMIN

(2)Connect Pin16 to GND via a 0.1uF capacitor.

(3)For Brightness 127/64/0, measure the DC level of picture period

at Pin20,

Ysm Mode:1

Brightness:

0/64/127

that is "V_TXBRMAX" / "V_TXBRCEN" / "V_TXBRMIN".

Others:Preset

T12

T13

Analog RGB Mode RGB Mute:0

(1)Input a cmposite sync signal into Pin38.

(2)Input a signal of NOTE:T9 figure into Pin16.

Switching Level

/ V_YS

Ysm Mode:1

RGB Contrast:32 (3)Increasing the Pin15 voltage, measure the voltage at which the

Others:Preset signal

inputted into Pin16 appears at Pin20, that is "V_YS".

Analog RGB Mode RGB Mute:0

(1)Input a 50IRE Y singnal with sync into Pin38&39.

Transfer

Characteristic

/ •R_YS

/ tPR_YS

/ •F_YS

R cut off:63

DC rest.:10

Ysm Mode:1

Others:Preset

(2)Connect Pin16 to GND via a 0.1uF capacitor.

(3)According to following figure, measure the Analog RGB Mode

Transfer

Characteristic.

1H

/ tPF_YS

20 ƒÊ

s

20 ƒÊ

s

Pin 15 In pu t

20

n

s

20

ns

50%

tPR

tPF

YS

Pin 20 Ou tpu t

100%

90%

50%

10%

0%

ƒÑR _YS

ƒÑF _YS

00/01/28 46

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

T14

Cross

Analog RGB to TV

/ CT_TX-TV

Talk

from RGB Mute:0

R cut off:63

(1) Input a composite sync signal into Pin38.

(2) Connect Pin39 to GND via a 1uF capacitor.

(3) Input a sine wave signal (f=4MHz, Video amplitude=0.5Vp-p)

into Pin16.

DC rest.:10

Ysm Mode:1

Uni-color:127

RGB contrast:63

Others:Preset

(4) Supply 0V to Pin15.

(5) Measure the amplitude at Pin20, that is V_TV.

(6) Supply 2V to Pin15.

(7) Measure the amplitude of 4MHz signal at Pin20, that is V_TX

.

(8) (8)Calculate;"CT_TX-TV"=20*log(V_TV/ V_TX)

T15

T16

Cross Talk from TV to RGB Mute:0

(1)Input a sine wave signal (f=4MHz, Video amplitude=0.5Vp-p)

with sync into Pin38&39.

(2)Connect Pin16 to GND via a 0.1uF capacitor.

(3)Supply 2V to Pin15.

(4)Measure the amplitude at Pin20, that is V_TX.

(5)Supply 0V to Pin15.

Analog RGB

/ CT_TV-TX

R cut off:63

DC rest.:10

Ysm Mode:1

Uni-color:127

RGB contrast:63

Others:Preset

(6)Measure the amplitude of 4MHz signal at Pin20, that is V_TV

(7)Calculate;"CT_TV-TX"=20*log(V_TX/ V_TV)

(1) Set S black monitor to 1.

.

SECAM Black Level

Adj. Characteristics

/ V_SECBMAX

RGB Mute:0

R cut off:63

DC rest.:10

Color

(2)For B-Y/R-Y Black Adj.:8, measure the DC level of picture period

at Pin22/20, that is V_SECBCEN/ V_SECRCEN

(3)For B-Y Black Adj.:0/15, measure the DC level change of picture

.

/ V_SECRMAX

/ V_SECBMIN

System:111 B-Y period against V_SECBCENat Pin22, that is "V_SECBMIN" / "V_SECBMAX".

/ V_SECRMIN

Black Adj:

(4)For R-Y Black Adj.:0/15, measure the DC level change of picture

period against V_SECRCENat Pin20, that is "V_SECRMIN" / "V_SECRMAX".

(5)Calculate; "•V_SECB"=(V_SECBMAX-V_SECBMIN)/16

SECAM Black Level

Adj. Data Sensitivity

/ •V_SECB

0/8/15

R-Y Black Adj:

0/8/15

"•V_SECR"=(V_SECRMAX-V_SECRMIN)/16

S black monitor:1

Others:Preset

RGB Mute:0

R cut off:63

DC rest.:10

Uni-color:127

Others:Preset

/ •V_SECR

T17

Base band TINT

characteristic

/ ••_BBMAX

(1)Input a signal(f0=100kHz, 100mVp-p) of NOTE T9 into

Pin44&38.

(2)Into Pin45, into a signal with the same amplitude but 90deg

phase advanced compared to the signal input to pin44.

(3)When baseband TINT is changed ‘10000’ to“00000”, measure

the amount of change in the output phase of Pin20, that is

“••_BBMIN”.

/ ••_BBMIN

(4) When baseband TINT is changed ‘10000’ to“11111”, measure

the amount of change in the output phase of Pin20, that is

“••_BBMIN”.

T18

RGB Mute:0

R/G/B cut off:63

Brightness:63

DC rest.:10

Color:0

Uni-color:127

Others:Preset

Analog RGB•RGB

Output Voltage Axes

Difference

••V_R-G

••V_G-B

(1)Input a 0IRE signal with sync into Pin38&39.

(2)Connect Pin16,17,18 to GND via 0.01•F.

(3)Measure the DC level of picture period at Pin20,21,22, that is

R_Y/G_Y/B_Y.

(4)Supply Pin15 to 2V.

(5) Measure the DC level of picture period at Pin20,21,22, that is

••V_B-R

R_T/G_T/B_T.

(6)Calculate;

•R • R_T• R_Y

•G • G_T• G_Y

•B • B_T• B_Y

“•V_R-G” • •R • •G

“•V_G-B” • •G • •B

“•V_B-R” • •B • •R

DEF STAGE

Note Items/Symbols

Bus conditoins

Measurement methods

D1

AFC Inactive Period

/ T_50AFCOFF

All:Preset

(1)Input a 50Hz/60Hz composite sync signal into Pin38.

(2)Measure "T_50AFCOFF" / "T_60AFCOFF" at Pin29. (cf. Fig.D1)

/ T_60AFCOFF

00/01/28 47

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

D2

D3

H-OUT Start Voltage

/ V_HON

All:Preset

(1)Let Pin1/14/37/42 be open.

(2)Increasing Pin31 voltage, measure the voltage at which H

OUT pulse appears at Pin32, that is "V_HON".

H-OUT Pulse Duty

/ W_HOUT

All:Preset

(1)Measure t_HOUT1& t_HOUT2at Pin32.

(2)Calculate;"W_HOUT"=t_HOUT1/(t_HOUT1+t_HOUT2)*100

t_HOUT1

t_HOUT2

D4

D5

H-OUT Freq. on AFC AFC

Gain:11 (1)Input a 50Hz composite sync signal into Pin38.

(2)Measure the H OUT frequency at Pin32, that is "F_HAFCOFF".

Stop Mode

/ F_HAFCOFF

Horizontal

Frequency

/ F_H50FR

(OFF)

Others:Preset

Free-run V-Freq:001/010

Others:Preset

For V-Freq 001/010, measure the H OUT frequency at Pin32, that

is "F_H50FR" / "F_H60FR".

/ F_H60FR

D6

D7

Horizontal

Variable Range

/ F_HMAX

Freq. All:Preset

(1)Connect Pin29 to Vcc via a 10k• and measure the H OUT

frequency at Pin32, that is "F_HMAX".

(2)Connect Pin29 to GND via a 68k• and measure the H OUT

frequency at Pin32, that is "F_HMIN".

/ F_HMIN

Horizontal

Freq. All:Preset

(1)Measure the Pin29 voltage at which H OUT frequency is

Control Sensitivity

/ •_HAFC

15.734kHz, that is V_H15734

(2)Measure the H OUT frequency when Pin29 voltage is V_H15734

.

+

50mV /V_H15734- 50mV, that is F_HHIGH/ F_HLOW

(3)Calculate;"•_HAFC"=(F_HHIGH-F_HLOW)/100

(1)Input a composite sync signal into Pin38.

(2)Decreasing the horizontal frequency from 17kHz, measure the

frequency at which H OUT synchronized with SCP Out(Pin29),

.

D8

Horizontal Pull-in

Range

/ •F_HPH

All:Preset

that is F_HPH

.

/ •F_HPL

(3)Increasing the horizontal frequency from 14kHz, measure the

frequency at which H OUT synchronized with SCP Out(Pin29),

that is F_HPL

.

(4)Calculate; "•F_HPH"=F_HPH-15734

"•F_HPL"=15625-F_HPL

D9

H-OUT Voltage

/ V_HOUTH

/ V_HOUTL

Horizontal Freq.

Dependence on Vcc

/ •F_HVCC

FBP Phase

/ PH_FBP

All:Preset

(1)Measure the high level of H OUT at Pin32, that is "V_HOUTH".

(2)Measure the low level of H OUT at Pin32, that is "V_HOUTL".

D10

D11

(1)Measure the H OUT frequency when H Vcc(Pin31) is

8.5V/9.5V, that is F_HVCCH/F_HVCCL.

(2)Calculate;"•F_HVCC"=(F_HVCCH-F_HVCCL)/1

(1)Input a composite sync signal into Pin38.

(2)According to the following figure, measure "PH_FBP" &

"PH_HSYNC".

H-Sync. Phase

/ PH_HSYNC

Sync in(Pin38)

H AFC(Pin29)

FBP in(Pin30)

00/01/28 48

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

D12

Horizontal

Position

H

Position:0/31 (1)Input a composite sync signal into Pin38.

Variable Range

Others:Preset

(2)Changing BUS data of “Horizontal Position” from 0 to 31,

/ •PH_HPOS

measure "•PH_HPOS" according to the following figure.

(00)

ƒ¢PH_HPOS

FBP in(Pin30)

(1F)

D13

D14

AFC-2 Pulse

Threshold Level

/ V_AFC2

H-BLK Pulse

Threshold Level

/ V_HBLK

All:Preset

(1)Input a composite sync signal into Pin38.

(2)Decreasing the FBP high level, measure the DC level at which

H OUT phase changes against Sync Out phase, that is "V_AFC2".

(1)Input a composite sync signal into Pin38.

(2)Increasing the FBP high level, measure the DC level at which

H blanking begins to work, that is "V_HBLK".

D15

Black Peak Det. Stop TEST:00001000

(1) Input a composite sync signal into Pin38.

Period (H)

/ PH_BPDET

/ W_BPDET

Black Stretch:01

Others:Preset

(2) According to the following figure, measure "PH_BPDET" &

"W_BPDET".

63.5ƒÊs

Sync in(Pin38)

4.7ƒÊs

0.25V

H AFC(Pin29)

ƒ¢PH_HPOS

4.3V

0V

W_BPDET

SCP OUT(Pin30)

D16

Gate Pulse Start

Phase

All:Preset

(1)Input a composite sync signal into Pin38.

(2)According to the following figure, measure "PH_GP" & "W_GP".

/ PH_GP

63.5ƒÊs

Gate Pulse Width

Sync in(Pin38)

4.7ƒÊs

0.25V

/ W_GP

H AFC(Pin29)

PH_GP

W_GP

4.3V

0V

SCP OUT(Pin30)

D17

D18

Vertical Oscillation

Start Voltage

/ V_VON

All:Preset

(1)Let Pin1/14/37/42 be open.

(2)Increasing Pin31 voltage, measure the voltage at which V

Ramp signal

(3)appears at Pin24, that is "V_VON".

(1)Input a 50Hz composite sync signal into Pin38.

(2)Set V-Freq to 000.

(3)For no input, measure the frequecy of V Ramp at Pin22, that is

"F_VAUFR50".

(3) Input a 60Hz composite sync signal into Pin38.

Vertical Free-run

Frequency

/ F_VAUFR50

/ F_VAUFR60

/ F_V50FR

V-Freq:

000/001/010

Others:Preset

/ F_V60FR

(4) Repeat (2)&(3), that is “F_VAUFR60”

(5) Set V-Freq. To 001/101, repeat (2), that is "F_V50FR" / "F_V60FR".

(1)Input a 50Hz/60Hz composite sync signal into Pin38.

(2)Measure "T_50GPM" / "T_60GPM" at Pin30. (cf. Fig.D21)

D19

Gate Pulse V-

Masking Period

/ T_50GPM

All:Preset

/ T_60GPM

00/01/28 49

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

D20

V. Ramp DC on

Service Mode

/ V_NOVRAMP

V STOP:1

Others:Preset

(1)Set V STOP to 1.

(2)Measure the DC level of Pin24, that is "V_NOVRAMP".

D21

Vertical Pull-in Range V-Freq:

(6) Input a composite sync signal into Pin38.

(Auto)

/ F_VPAUL

/ F_VPAUH

000/001/010

Others:Preset

(7) For V-Freq 000/001/010, increasing the input vertical period

from 220H by 0.5H step, measure the period at which input

signal synchronized with V Ramp(Pin24), that is "F_VPAUL" /”

Vertical Pull-in Range

(50Hz)

/ F_VP50L

F_VP50L”/ "F_VP60L".

(8) (3)For V-Freq 000/001/010, decreasing the input vertical

period from 360H by 0.5H step, measure the period at which

input signal synchronized with V Ramp, that is "F_VPAUH" /”

/ F_VP50H

Vertical Pull-in Range

(60Hz)

F_VP50H”/ "F_VP60H".

/ F_VP60L

/ F_VP60H

D22

D23

Vertical Period on V-Freq:

For V-Freq 100/101/110/111, measure the vertical period at SCP

out (Pin30), that is "T_V312.5"/"T_V262.5" / "T_V313"/"T_V263" .

Fixed Mode

/ T_V3125

100/101/110/

111

/ T_V2625

Others:Preset

/ T_V313

/ T_V263

V-BLK Start Phase

/ PH_50VBLK

/ PH_60VBLK

V-BLK Width

/ W_50VBLK

All:Preset

(1)Input a 50Hz/60Hz composite sync signal into Pin38.

(2)Measure "T_50AFCOFF" / "1T_60AFCOFF" at Pin30. (cf. Fig.D25)

/ W_60VBLK

D24

Sand Castle Pulse All:Preset

Measure "V_SCPH" / "V_SCPM" / "V_SCPL" at Pin30.

Level

V_SCPH

/ V_SCPH

/ V_SCPM

/ V_SCPL

V_SCPM

V_SCPL

D25

D26

Vertical

Amplitude

/ V_VRAMP

Vertical AMP Gain

/ G_VAMP

Ramp All:Preset

Measure the V Ramp amplitude at Pin24, that is "V_VRAMP".

All:Preset

(1)Let Pin26 be open.

(2)Changing the Pin25 DC voltage, measure "V_VOMAX" / "V_VOMIN" /

Vertical AMP

Max.Output Level

/ V_VOMAX

Vertical AMP

Min.Output Level

"G_VAMP"

according to a following figure.

#26DC

/ V_VOMIN

V_VOMAX

ƒ¢V=GVAMP

=20log(ƒ¢V#26/ƒ¢V#25)

V_VOMIN

#25DC

D27

Vertical

AMP All:Preset

(1)Supply 7V to Pin25.

Max.Output Current

/ I_VOMAX

(2)Measure the current from Pin26 to GND, that is "I_VOMAX".

00/01/28 50

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

Note Items/Symbols

Bus conditoins

Measurement methods

D28

Vertical NFB

Amplitude

/ V_NFB

V Size:0/32/63 (1)Measure the amplitude of NFB V Ramp at Pin25, that is

Others:Preset

"V_NFB". (2)Measure the amplitude of NFB V Ramp at Pin25 for V-

Size 0/63, that is

Vertical Amplitude

Variable Range

/ •V_VRAMPH

V_NFBMIN/ V_NFBMAX.

(3)Calculate; "•V_VRAMPH"=(V_NFBMAX-V_NFB)/V_NFB*100

"•V_VRAMPL"=(V_NFBMIN-V_NFB)/V_NFB*100

/ •V_VRAMPL

D29

Vertical

Linearity

V

Linearity:0/8/15 (1)For V Linearity 8, measure V₁(from center to max.) and

Variable Range

/ •V_LIN1+

/ •V_LIN1-

/ •V_LIN2+

Others:Preset

V₂(from center to min.) at Pin24 according to a follownig figure.

(2)For V Linearity 15/0, measure V_LIN1+/ V_LIN1-and V_LIN2+/ V_LIN2-

(3)Calculate; "•V_LIN1+"=(V_LIN1+-V₁)/V1*100

"•V_LIN1-"=(V_LIN1--V₁)/V₁*100

.

"•V_LIN2+"=(V_LIN2+-V₂)/V₂*100

/ •V_LIN2-

"•V_LIN2-"=(V_LIN2--V₂)/V₂*100

Pin24

signal

V1

V2

D30

D35

Vertical S Correction

Variable Range

/ •V_S1+

/ •V_S1-

/ •V_S2+

V

S

Corr.:0/8/15 (1)For V S Correction:8, measure V₁and V₂at Pin24 according to

Others:Preset

a figure of NOTE:D32 .

(2)For V S Correction:15/0, measure V_S1+/ V_S1-and V_S2+/ V_S2-

(3)Calculate; "•V_S1+"=(V_S1+-V₁)/V₁*100

"•V_S1-"=(V_S1--V₁)/V₁*100

.

"•V_S2+"=(V_S2+-V₂)/V₂*100

"•V_S2-"=(V_S2--V₂)/V₂*100

Decreasing the Pin25 voltage from 5V, measure the voltage at

which Pin20 output drops to blanking level, that is "V_VG".

/ •V_S2-

Vertical

Voltage

/ V_VG

Guard All:Preset

00/01/28 51

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

R50:51kƒ¶

+

CE24:10ƒÊF

R51:

51kƒ¶

VR2:

50kB

VR1:

50kB

+

CE25:100ƒÊF

C16:0.01ƒÊF

CE13:100ƒÊF

+

C31:0.01ƒÊF

CE26:47ƒÊF

+

SW3:

CE14:0.22ƒÊF

R35:8.2kƒ¶

C32:0.01ƒÊF

C15:0.1ƒÊF

H.AFC Filter

ABCL IN

+

C17:

R33:10kƒ¶ D1:

C106:2200pF

+

8200pF

CE27:100ƒÊF

R34:15kƒ¶

FBP IN/

SCP OUT

ref R

V OUT

V NFB

R29:5.6kƒ¶,1%

C18:0.01ƒÊF

C14:0.47ƒÊF

R30:1kƒ¶

H Vcc(9V)

H OUT

+

R53:

4.7kƒ¶

R32:1kƒ¶

CE15:100ƒÊF

Q10:

R31:510ƒ¶

R36:

C13:8200pF

390ƒ¶

R37:

91ƒ¶

CE31:0.47ƒÊF

+

R52:

4.7kƒ¶

SW2:

Dig. GND

SCL

ZD1:

4.7v

V RAMP

IK IN

R22:100ƒ¶

R24:100ƒ¶

Q4:

R38:100ƒ¶

R39:100ƒ¶

R21:100ƒ¶

R20:3kƒ¶

R23:10kƒ¶

Q5:

SDA

B OUT

G OUT

R19:100ƒ¶

R18:3kƒ¶

+

R40:0pen

Q6:

Q7:

CE28:47ƒÊF

BLACK Det

Dig. VDD

Sync IN

Y IN

+

C019:

0.01ƒÊF

R17:100ƒ¶

R16:3kƒ¶

CE16:1ƒÊF

R OUT

+

R15:100ƒ¶

CE17:100ƒÊF

Q8:

Q9:

+

Y/C GND

EXT.B IN

EXT.G IN

EXT.R IN

Ys/Ym SW

RGB Vcc(9V)

CW OUT

CE18:1ƒÊF

C12:0.1ƒÊF

R26:510ƒ¶

R27:510ƒ¶

+

CE19:0.22ƒÊF

CE29:

47ƒÊF

R28:1.2kƒ¶

R14:75ƒ¶

C11:0.1ƒÊF

+

R203:

2kƒ¶

DC Restor

MON OUT

CE11:100ƒÊF

C20:0.1ƒÊF

R201:

1kƒ¶

R202:

1kƒ¶

R13:75ƒ¶

C10:0.1ƒÊF

C33:

0.01ƒÊF

+

C021:0.01ƒÊF

+

R12:75ƒ¶

CE30:100ƒÊF

Y/C Vcc(5V)

C IN

R300:10kƒ¶

CE20:100ƒÊF

CE10:100ƒÊF

+

CE21:1ƒÊF

+

75ƒ¶

C9:0.01ƒÊF

C22:0.1ƒÊF

C23:0.1ƒÊF

R11:

Q3:

U IN

X1:

75ƒ¶

4.433619MHz

C8:9pF

V IN

X'tal

R204:75ƒ¶

C7:2200pF

+

EXT IN

APC Filter

IF AGC

CE201:1ƒÊF

R10:33kƒ¶ CE9:0.22ƒÊF

CE8:2.2ƒÊF

+

CE22:0.22ƒÊF

+

R41:470ƒ¶

LOOP Filter

TV IN

C302:

0.01ƒÊF

CE202:1ƒÊF

+

R8:33kƒ¶

C24:1000pF

RF AGC

+

CE7:4.7ƒÊF

DE-EMP.

PIF tank

DC NF

NC

C25:0.01ƒÊF

C6:0.01ƒÊF

IF IN

R46:

1kƒ¶

C4

IF IN

R45:

C5:

330ƒ¶

CE23:10ƒÊF

+

0.01ƒÊF

Q1:

IF GND

R6:

Q2:

R205:680ƒ¶

F1:Trap

+

R5:

R3:

R4:

EXT AUDIO

AUDIO OUT

SIF OUT

RIPPLE FIL

IF Vcc

CE203:4.7ƒÊF

R2:

+

IF DET OUT

AFT OUT

CE6:

C3:

R43:2kƒ¶

CE3:

22ƒÊF

R1:

R42:3kƒ¶

+

L2:

R47:51ƒ¶

P1:

C26:0.1ƒÊF

+5V

+9V

SIF IN•^

H CORRECTION IN

C27:0.01ƒÊF

Reg.

C28:0.01ƒÊF

R49:1kƒ¶

L1:12ƒÊH

R48:1kƒ¶

F2:

BPF

00/01/28 52

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

00/01/28 53

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

0.01ƒÊF

+

100ƒÊF

CE26:47ƒÊF

CE14:0.22ƒÊF

R35:8.2kƒ¶

+

C15:0.1ƒÊF

H.AFC Filter

ABCL IN

+

C17:

8200pF

R33:10kƒ¶ D1:

C106:2200pF

C32:0.01ƒÊF

R34:15kƒ¶

FBP IN/

SCP OUT

ref R

V OUT

V NFB

R29:5.6kƒ¶,1%

+

C18:0.01ƒÊF

C14:0.47ƒÊF

CE27:100ƒÊF

R30:1kƒ¶

H Vcc(9V)

H OUT

+

R32:1kƒ¶

CE15:100ƒÊF

Q10:

R31:510ƒ¶

R36:

C13:8200pF

390ƒ¶

R37:

91ƒ¶

CE31:0.47ƒÊF

+

Dig. GND

SCL

ZD1:

4.7v

V RAMP

IK IN

R38:100ƒ¶

R39:100ƒ¶

R21:100ƒ¶

R20:3kƒ¶

SDA

B OUT

G OUT

R19:100ƒ¶

R18:3kƒ¶

R40:0pen

BLACK Det

Dig. VDD

Sync IN

Y IN

+

R17:100ƒ¶

R16:3kƒ¶

C019:0.01ƒÊF CE16:1ƒÊF

R OUT

+

R15:100ƒ¶

CE17:100ƒÊF

+

Y/C GND

EXT.B IN

EXT.G IN

EXT.R IN

Ys/Ym SW

RGB Vcc(9V)

CW OUT

CE18:1ƒÊF

C12:0.1ƒÊF

+

CE19:0.22ƒÊF

R14:75ƒ¶

C11:0.1ƒÊF

R203:

2kƒ¶

DC Restor

MON OUT

C20:0.1ƒÊF

R201:

1kƒ¶

R202:

1kƒ¶

R13:75ƒ¶

C10:0.1ƒÊF

C021:0.01ƒÊF

+

R12:75ƒ¶

Y/C Vcc(5V)

C IN

R300:10kƒ¶

CE20:100ƒÊF

CE10:100ƒÊF

+

CE21:1ƒÊF

+

75ƒ¶

C9:0.01ƒÊF

C22:0.1ƒÊF

C23:0.1ƒÊF

R11:

Q3:

U IN

V IN

X1:

75ƒ¶

4.433619MHz

C8:9pF

X'tal

R204:75ƒ¶

C7:2200pF

+

EXT IN

APC Filter

IF AGC

CE201:1ƒÊF

R10:33kƒ¶

CE9:0.22ƒÊF

CE8:2.2ƒÊF

CE22:0.22ƒÊF

+

R41:470ƒ¶

+

LOOP Filter

TV IN

C302:

0.01ƒÊF

CE202:1ƒÊF

R8:33kƒ¶

C24:1000pF

C25:0.01ƒÊF

RF AGC

+

CE7:4.7ƒÊF

DE-EMP.

PIF tank

NC

C6:0.01ƒÊF

IF IN

R46:

1kƒ¶

C4

IF IN

R45:

330ƒ¶

C5:

0.01ƒÊF

CE23:10ƒÊF

+

Q1:

DC NF

IF GND

R6:

R205:680ƒ¶

Q2:

R4:

F1:Trap

R5:

R3:

+

EXT AUDIO

AUDIO OUT

SIF OUT

RIPPLE FIL

IF Vcc

CE203:4.7ƒÊF

R2:

R1:

+

IF DET OUT

AFT OUT

CE6:

C3:

R43:2kƒ¶

CE3:

R42:3kƒ¶

22ƒÊF

+

L2:

P1:

C26:0.1ƒÊF

C28:0.01ƒÊF

R48:1kƒ¶

R49:1kƒ¶

+5V

+9V

SIF IN•^

H CORRECTION IN

Reg.

L1:12ƒÊH

F2:

BPF

0.01ƒÊF

+

100ƒÊF

00/01/28 54

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

OUTLINE DRAWING

Unit : mm

SDIP56-P-600-1.78

00/01/28 55

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

••••

•••

••

p.1

IF stage

for L system,AM sound demodulation

U/V input ports

Chroma stage

Cb/Cr input ports

RF AGC

BIAS

P.2

Block Diagram Pin9

RFAGC/SIF in

Ripple filter

••

L-SECAM AM

••••••

H.AFC

Pin3 SIF OUT Interface

9V

14

P.3

14

100ƒ¶

500ƒ¶

15kƒ¶

500ƒ¶

15kƒ¶

3

16kƒ¶

8.3kƒ¶

16.3kƒ¶

8.3kƒ¶

5

9V

Pin4 Audio out Interface

14

100ƒ¶

ATT

4

50kƒ¶

5.3V

4.5V

30kƒ¶

5

90dB•

90dB(•V)(Pin6-7)

P.3

P.4

Pin6,7 IF IN

field intensity

level

Pin8 RF AGC/SIF IN

RF AGC/SIF IN

RF AGC

••

This terminal also lead to 1’st SIF

input pole.

00/01/28 56

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

9V

5V

14

300ƒ¶

9

8

30kƒ¶

to SELF ADJ

30kƒ¶

5

1

500ƒ¶

10kƒ¶

5

2.2•F

P.4

P.8

Pin10 IF AGC

Pin36 Black DET

2.2mF

42

4kƒ¶

36

2.5V

19

42

P.9

Pin40 DC restor

50k

40

10k

19

Pin38 Sync in

Pin44,45 U/V in

1401IRE

U/V in

27pF

140IRE

Cb/Cr in

18pF

p.10

P.11

p.14

Pin50,51 PIF tank

RF AGC

RF AGC delay point

RF AGC delay point (Pin6-7)

01: 65 dB(•V)

01:

65dBm

3F: 100 dB(•V)

3F:

100dBm

P.15

p.16

p.17

p.18

p.19

DDS MODE SW•••

Split / Inter•••

U/V SW

••

U/V

Cb/Cr

••

Self Test

01:B OUT

Self Adj.

10:R OUT

Self Adj.

Self Test

00/01/28 57

Ver3.7

ꢀꢁꢂꢃꢄꢅꢆ

ꢀꢅꢇꢈꢉꢊꢋ

00: AFT (Normal) 10: RF AGC X

1/2

Noise Det•

(*3)Pin 1, 4, 5, 11, 12, 19, 26, 33, 34,

35, 42, 50, 51 are weak against •…

(*3)Pin 1, 4, 5, 6, 9, 11, 12, 13, 19, 26,

31, 32, 33, 34, 35, 37, 42, 43, 50, 51

are weak against •…

p.22 (*3)

Cut off/Drive•spec.••

Drive•spec.••

min. typ. max.

•••

p.29

T4,T5

Drive•spec.••

min. typ. max.

2.5 3.5 4.5

-8.0 -5.5 -4.5

T5 spec.••

3 3.5

4

-6.0 -5.5 -5.0

••

T18

S2

p.35

p.36

Input a signal that 4.5[MHz],

100[dB V], 2.5[kHz]…•

Input a signal that 4.5[MHz],

100[dB V], 25[kHz]…•

Input a signal that 4.5[MHz],

100[dB V], 25[kHz]…•

Input a signal that 4.5[MHz],

100[dB V], 25[kHz]…•

••

S3

S8

Input a signal that 4.5[MHz],

100[dB V], 2.5[kHz]…•

Input a signal that 4.5[MHz],

100[dB V], 2.5[kHz]…•

p.48

p.54

T18

pin9

RF AGC/SIF IN

10•F

RF AGC

22•F

Pin2 Ripple filter

Pin9

p.55

RF AGC/SIF IN

RF AGC

00/01/28 58

Ver3.7


型号：	TB1254N
厂家：	TOSHIBA
描述：	PAL / NTSC / SECAM 1CHIP (IF+VCD PROCESSOR) IC PAL / NTSC / SECAM 1CHIP （ IF + VCD处理器） IC CD
文件：	总58页 (文件大小：530K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TB1254N [TOSHIBA]

相关型号：

TB1255A

TB1256A

TB1261F

TB1262F

TB1263A

TB1265A

TB1270A

TB1274BFG

TB1277A

TB1278A

TB1279A

TB1280A