TC74VCXH16543(SP,F [TOSHIBA]
ALVC/VCX/A SERIES, DUAL 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO56;
| 型号： | TC74VCXH16543(SP,F |
| 厂家： | 
TOSHIBA |
| 描述： | ALVC/VCX/A SERIES, DUAL 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO56 光电二极管 输出元件 |
| 文件： | 总15页 (文件大小：264K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TC74VCXH16543FT
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC74VCXH16543FT
Low-Voltage 16-Bit Registered Transceiver with Bushold
The TC74VCXH16543FT is a high-performance CMOS 16-bit
registered transceiver. Designed for use in 1.8-V, 2.5-V or 3.3-V
systems, it achieves high-speed operation while maintaining the
CMOS low power dissipation.
The TC74VCXH16543FT can be used as two 8-bit transceivers
or one 16-bit transceiver. Separate latch-enable (LEAB or LEBA)
and output-enable (OEAB or OEBA) inputs are provided for each
register to permit independent control in either direction of data
flow.
The A-to-B enable (CEAB) input must be low in order to enter
data from A or to output data from B. If CEAB is low and LEAB
is low, the A-to-B latches are transparent; a subsequent
Weight: 0.25 g (typ.)
low-to-high transition of LEAB puts the Alatches in the storage mode. With CEAB and OEAB both low, the 3-state
B outputs are active and reflect the data present at the output of the A latches.
Data flow from B to A is similar but requires using the CEBA, LEBA, and OEAB inputs.
When the OE input is high, the outputs are in a high-impedance state. This device is designed to be used with
3-state memory address drivers, etc.
The A, B data inputs include active bushold circuitry, eliminating the need for external pull-up resistors to hold
unused or floating data inputs at a valid logic level.
All inputs are equipped with protection circuits against static discharge.
Features (Note)
•
•
•
Low-voltage operation: V
= 1.8 to 3.6 V
CC
Bushold on data inputs eliminating the need for external pull-up/pull-down resistors
High-speed operation: t = 3.5 ns (max) (V
= 3.0 to 3.6 V)
= 2.3 to 2.7 V)
= 1.8 V)
pd
CC
CC
CC
: t = 4.0 ns (max) (V
pd
: t = 8.0 ns (max) (V
pd
•
•
3.6-V tolerant control inputs
Output current: I /I
= ±24 mA (min) (V
= ±18 mA (min) (V
= 3.0 V)
= 2.3 V)
OH OL
CC
: I /I
OH OL
CC
: I /I
OH OL
= ±6 mA (min) (V
= 1.8 V)
CC
•
•
Latch-up performance: −300 mA
ESD performance:Machine model ≥ ±200 V
Human body model ≥ ±2000 V
•
Package: TSSOP
Note:
Do not apply a signal to any bus pins when it is in the output mode. Damage may result.
Start of commercial production
2001-03
1
2014-03-01
TC74VCXH16543FT
Pin Assignment (top view)
IEC Logic Symbol
56
54
55
1
1
2
3
4
5
6
7
8
9
56
55
54
1EN3
G1
1OEAB
1LEAB
1OEBA
1LEBA
1OEBA
1CEBA
1LEBA
C5
2EN4
G2
1OEAB
1CEAB
1LEAB
2OEBA
2CEBA
2LEBA
2OEAB
2CEAB
2LEAB
1CEAB
GND
1A1
1CEBA
3
2
53 GND
52 1B1
51 1B2
2C6
7EN9
G7
29
31
30
28
26
27
7C11
8EN10
G8
1A2
V
50
V
CC
CC
8C12
1A3
1A4
49 1B3
48 1B4
47 1B5
46 GND
45 1B6
44 1B7
43 1B8
42 2B1
41 2B2
40 2B3
39 GND
38 2B4
37 2B5
36 2B6
52
5
3
5D
1B1
1A1
6D
4
1A5 10
GND 11
1A6 12
1A7 13
1A8 14
2A1 15
2A2 16
2A3 17
GND 18
2A4 19
2A5 20
2A6 21
6
51
49
48
47
45
44
43
42
1A2
1A3
1A4
1A5
1A6
1A7
1A8
2A1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
2B1
8
9
10
12
13
14
15
9
11D
10
12D
16
17
19
41
40
38
2A2
2A3
2A4
2B2
2B3
2B4
V
22
35
V
CC
CC
20
21
37
36
2A5
2A6
2B5
2B6
2A7 23
2A8 24
GND 25
34 2B7
33 2B8
32 GND
23
24
34
33
2A7
2A8
2B7
2B8
26
2LEAB 27
28
31
30
29
2CEAB
2CEBA
2LEBA
2OEBA
2OEAB
2
2014-03-01
TC74VCXH16543FT
Truth Table (A bus → B bus each 8-bit latch)
Inputs
Outputs
B
CEAB
LEAB
OEAB
A
X
X
X
H
X
L
X
X
H
X
H
L
Z
Z
B0
(Note)
L
L
L
L
L
L
L
L
H
H
Note:
Output level before the indicated steady-state input conditions were established.
Truth Table (B bus → A bus each 8-bit latch)
Inputs
Outputs
A
CEBA
LEBA
OEBA
B
X
X
X
H
X
L
X
X
H
X
H
L
Z
Z
A0
(Note)
L
L
L
L
L
L
L
L
H
H
Note:
Output level before the indicated steady-state input conditions were established.
3
2014-03-01
TC74VCXH16543FT
System Diagram
56
54
55
1
1OEBA
1CEBA
1LEBA
1OEAB
1CEAB
1LEAB
1A1
3
2
LE
D
5
52
1B1
LE
D
To seven other channels
29
31
30
28
26
27
15
2OEBA
2CEBA
2LEBA
2OEAB
2CEAB
2LEAB
2A1
LE
D
42
2B1
LE
D
To seven other channels
4
2014-03-01
TC74VCXH16543FT
Absolute Maximum Ratings (Note 1)
Characteristics
Power supply voltage
Symbol
Rating
Unit
V
V
−0.5 to 4.6
−0.5 to 4.6
CC
( OEAB , OEBA , LEAB ,
LEBA , CEAB , CEBA )
DC input
voltage
V
V
IN
−0.5 to V
CC
+ 0.5
(An, Bn)
(An, Bn)
(Note 2)
−0.5 to V
CC
+ 0.5
DC output
voltage
V
V
OUT
(Note 3)
Input diode current
Output diode current
Output current
I
−50
±50
mA
mA
mA
mW
mA
°C
IK
I
(Note 4)
OK
I
±50
OUT
Power dissipation
P
400
D
DC V /ground current per supply pin
CC
I
/I
CC GND
±100
Storage temperature
T
stg
−65 to 150
Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or
even destruction.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 2: OFF state
Note 3: High or low state. I
OUT
absolute maximum rating must be observed.
Note 4:
V
OUT
< GND, V
OUT
> V
CC
5
2014-03-01
TC74VCXH16543FT
Operating Ranges (Note 1) (Note 2)
Characteristics
Symbol
Rating
Unit
V
1.8 to 3.6
Power supply voltage
V
CC
1.2 to 3.6 (Note 3)
( OEAB , OEBA , LEAB ,
LEBA , CEAB , CEBA )
−0.3 to 3.6
Input
voltage
V
V
V
IN
(An, Bn)
(An, Bn)
0 to V
0 to V
(Note 4)
(Note 5)
CC
CC
Output
voltage
V
OUT
/I
±24
±18
(Note 6)
(Note 7)
(Note 8)
Output current
I
mA
OH OL
±6
Operating temperature
Input rise and fall time
T
−40 to 85
°C
opr
dt/dv
0 to 10 (Note 9)
ns/V
Note 1: The operating ranges must be maintained to ensure the normal operation of the device.
Unused inputs must be tied to either V or GND.
CC
Note 2: Floating or unused control inputs must be held high or low.
Note 3: Data retention only
Note 4: OFF state
Note 5: High or low state
Note 6:
Note 7:
Note 8:
Note 9:
V
V
V
V
= 3.0 to 3.6 V
= 2.3 to 2.7 V
= 1.8 V
CC
CC
CC
= 0.8 to 2.0 V, V
CC
= 3.0 V
IN
6
2014-03-01
TC74VCXH16543FT
Electrical Characteristics
DC Characteristics (Ta = −40 to 85°C, 2.7 V < V ≤ 3.6 V)
CC
Characteristics
Symbol
Test Condition
Min
Max
Unit
V
V
(V)
CC
H-level
V
IH
⎯
⎯
2.7 to 3.6
2.7 to 3.6
2.0
⎯
Input voltage
L-level
H-level
V
IL
⎯
0.8
V
CC
I
= −100 μA
2.7 to 3.6
⎯
OH
− 0.2
2.2
2.4
2.2
⎯
I
I
I
I
I
I
I
= −12 mA
= −18 mA
= −24 mA
= 100 μA
= 12 mA
= 18 mA
= 24 mA
2.7
3.0
⎯
⎯
OH
OH
OH
OL
OL
OL
OL
V
OH
V
= V or V
IH
IN
IL
3.0
⎯
Output voltage
V
2.7 to 3.6
2.7
0.2
0.4
0.4
0.55
⎯
L-level
V
OL
V
V
= V or V
IH
IN
IL
3.0
⎯
3.0
⎯
Input leakage current
I
IN
= 0 to 3.6 V
2.7 to 3.6
⎯
±5.0
μA
μA
IN
( OEAB , OEBA , LEAB ,
LEBA , CEAB , CEBA )
V
V
= 0.8 V
= 2.0 V
3.0
3.0
3.6
3.6
75
−75
⎯
⎯
⎯
IN
Bushold input minimum drive hold
current
I
I (HOLD)
IN
(Note 1)
(Note 2)
450
−450
Bushold input over-drive current to
change state
I
μA
μA
I (OD)
⎯
V
V
= V or V
IH IL
IN
3-state output OFF state current
Quiescent supply current
I
2.7 to 3.6
⎯
±10.0
OZ
= V or GND
OUT
CC
I
V
V
= V
or GND
2.7 to 3.6
2.7 to 3.6
⎯
⎯
20.0
750
μA
μA
CC
IN
CC
CC
Increase in I
per input
ΔI
CC
= V
− 0.6 V
CC
IH
Note 1: An external driver must source at least the specified current to switch from LOW-to-HIGH.
Note 2: An external driver must sink at least the specified current to switch from HIGH-to-LOW.
7
2014-03-01
TC74VCXH16543FT
DC Characteristics (Ta = −40 to 85°C, 2.3 V ≤ V ≤ 2.7 V)
CC
Characteristics
Symbol
Test Condition
Min
Max
Unit
V
V
(V)
CC
H-level
V
IH
⎯
⎯
2.3 to 2.7
2.3 to 2.7
1.6
⎯
Input voltage
L-level
H-level
V
IL
⎯
0.7
V
CC
I
= −100 μA
2.3 to 2.7
⎯
OH
− 0.2
2.0
1.8
1.7
⎯
I
I
I
I
I
I
= −6 mA
= −12 mA
= −18 mA
= 100 μA
= 12 mA
= 18 mA
2.3
2.3
⎯
⎯
OH
OH
OH
OL
OL
OL
V
OH
V
= V or V
IN
IH
IL
Output voltage
V
2.3
⎯
2.3 to 2.7
2.3
0.2
0.4
0.6
L-level
V
OL
V
V
= V or V
⎯
IN
IH
IL
2.3
⎯
Input leakage current
I
IN
= 0 to 3.6 V
2.3 to 2.7
⎯
±5.0
μA
IN
( OEAB , OEBA , LEAB ,
LEBA , CEAB , CEBA )
V
V
= 0.7 V
= 1.6 V
2.3
2.3
2.7
2.7
45
−45
⎯
⎯
⎯
IN
Bushold input minimum drive hold
current
I
μA
μA
I (HOLD)
IN
(Note 1)
(Note 2)
300
−300
Bushold input over-drive current to
change state
I
I (OD)
⎯
V
V
= V or V
IH IL
IN
3-state output OFF state current
Quiescent supply current
I
2.3 to 2.7
2.3 to 2.7
⎯
⎯
±10.0
μA
μA
OZ
= V or GND
OUT
CC
I
V
IN
= V
CC
or GND
20.0
CC
Note 1: An external driver must source at least the specified current to switch from LOW-to-HIGH.
Note 2: An external driver must sink at least the specified current to switch from HIGH-to-LOW.
8
2014-03-01
TC74VCXH16543FT
DC Characteristics (Ta = −40 to 85°C, 1.8 V ≤ V < 2.3 V)
CC
Characteristics
Symbol
Test Condition
Min
Max
Unit
V
V
(V)
CC
0.7 ×
H-level
V
IH
⎯
⎯
1.8 to 2.3
1.8 to 2.3
1.8
⎯
V
CC
Input voltage
0.2 ×
L-level
H-level
V
IL
⎯
V
CC
V
CC
I
= −100 μA
⎯
OH
− 0.2
V
OH
V
IN
V
IN
V
IN
= V or V
IH
IL
I
I
I
= −6 mA
= 100 μA
= 6 mA
1.8
1.8
1.8
1.4
⎯
⎯
OH
OL
OL
Output voltage
V
0.2
0.3
L-level
V
= V or V
IH
OL
IN
IL
⎯
Input leakage current
I
= 0 to 3.6 V
1.8
⎯
±5.0
μA
( OEAB , OEBA , LEAB ,
LEBA , CEAB , CEBA )
V
V
= 0.36 V
= 1.26 V
1.8
1.8
1.8
1.8
25
−25
⎯
⎯
⎯
IN
Bushold input minimum drive hold
current
I
μA
μA
I (HOLD)
IN
(Note 1)
(Note 2)
200
−200
Bushold input over-drive current to
change state
I
I (OD)
⎯
V
V
= V or V
IH IL
IN
3-state output OFF state current
Quiescent supply current
I
1.8
1.8
⎯
⎯
±10.0
μA
μA
OZ
= V or GND
OUT
CC
I
V
IN
= V
CC
or GND
20.0
CC
Note 1: An external driver must source at least the specified current to switch from LOW-to-HIGH.
Note 2: An external driver must sink at least the specified current to switch from HIGH-to-LOW.
9
2014-03-01
TC74VCXH16543FT
AC Characteristics (Ta = −40 to 85°C, input: t = t = 2.0 ns, C = 30 pF, R = 500 Ω) (Note 1)
r
f
L
L
Characteristics
Symbol
Test Condition
Min
Max
Unit
ns
V
(V)
CC
1.8
1.5
0.8
0.6
1.5
0.8
0.6
1.5
0.8
0.6
1.5
0.8
0.6
4.0
1.5
1.5
2.5
1.5
1.5
1.0
1.0
1.0
⎯
8.0
4.0
3.5
9.8
5.0
3.9
9.8
4.9
3.8
7.6
4.2
3.7
⎯
Propagation delay time
(An, Bn-Bn, An)
t
t
pLH
Figure 1, Figure 2
2.5 ± 0.2
3.3 ± 0.3
1.8
pHL
Propagation delay time
( LEAB , LEBA -Bn, An)
t
t
pLH
Figure 1, Figure 2
ns
ns
ns
ns
ns
ns
ns
2.5 ± 0.2
3.3 ± 0.3
1.8
pHL
3-state output enable time
t
pZL
Figure 1, Figure 4
2.5 ± 0.2
3.3 ± 0.3
1.8
( OEAB , OEBA , CEAB ,
CEBA )
t
pZH
3-state output disable time
t
pLZ
Figure 1, Figure 4
2.5 ± 0.2
3.3 ± 0.3
1.8
( OEAB , OEBA , CEAB ,
CEBA )
t
pHZ
Minimum pulse width
t
Figure 1, Figure 2, Figure 3
Figure 1, Figure 2, Figure 3
Figure 1, Figure 2, Figure 3
2.5 ± 0.2
3.3 ± 0.3
1.8
⎯
W (L)
( LEAB , LEBA , CEAB , CEBA )
⎯
⎯
Minimum setup time
(An, Bn- LE , CE )
t
s
2.5 ± 0.2
3.3 ± 0.3
1.8
⎯
⎯
⎯
Minimum hold time
(An, Bn- LE , CE )
t
h
2.5 ± 0.2
3.3 ± 0.3
1.8
⎯
⎯
0.5
0.5
0.5
t
t
osLH
Output to output skew
(Note 2)
2.5 ± 0.2
3.3 ± 0.3
⎯
osHL
⎯
Note 1: For C = 50 pF, add approximately 300 ps to the AC maximum specification.
L
Note 2: Parameter guaranteed by design.
(t
= |t
− t
|, t
pLHn osHL
= |t
− t
|)
pHLn
osLH
pLHm
pHLm
10
2014-03-01
TC74VCXH16543FT
Dynamic Switching Characteristics
(Ta = 25°C, input: t = t = 2.0 ns, C = 30 pF, R = 500 Ω)
r
f
L
L
Characteristics
Test Condition
Symbol
Typ.
Unit
V
V
CC
(V)
V
IH
V
IH
V
IH
V
IH
V
IH
V
IH
V
IH
V
IH
V
IH
= 1.8 V, V = 0 V
(Note)
(Note)
(Note)
(Note)
(Note)
(Note)
(Note)
(Note)
(Note)
1.8
0.25
0.6
IL
Quiet output maximum
dynamic V
V
OLP
= 2.5 V, V = 0 V
2.5
3.3
1.8
2.5
3.3
1.8
2.5
3.3
IL
OL
= 3.3 V, V = 0 V
IL
0.8
= 1.8 V, V = 0 V
−0.25
−0.6
−0.8
1.5
IL
Quiet output minimum
dynamic V
V
OLV
V
V
= 2.5 V, V = 0 V
IL
OL
= 3.3 V, V = 0 V
IL
= 1.8 V, V = 0 V
IL
Quiet output minimum
V
OHV
= 2.5 V, V = 0 V
1.9
IL
dynamic V
OH
= 3.3 V, V = 0 V
IL
2.2
Note:
Parameter guaranteed by design.
Capacitive Characteristics (Ta = 25°C)
Characteristics
Symbol
Test Condition
Typ.
Unit
V
CC
(V)
Input capacitance
C
1.8, 2.5, 3.3
1.8, 2.5, 3.3
6
7
pF
pF
pF
IN
I/O
PD
⎯
Bus I/O capacitance
C
C
Power dissipation capacitance
f
IN
= 10 MHz
(Note) 1.8, 2.5, 3.3
20
Note:
C
PD
is defined as the value of the internal equivalent capacitance which is calculated from the operating
current consumption without load.
Average operating current can be obtained by the equation:
I
= C ･V ･f + I /16 (per bit)
PD CC IN CC
CC (opr)
11
2014-03-01
TC74VCXH16543FT
AC Test Circuit
6.0 V or V
Open
GND
× 2
CC
Parameter
Switch
Open
Switch
t
, t
pLH pHL
6.0 V
V × 2
CC
@V
@V
@V
= 3.3 ± 0.3 V
= 2.5 ± 0.2 V
= 1.8 V
CC
CC
CC
Output
Measure
t
, t
pLZ pZL
C
R
= 30 pF
= 500 Ω
L
t
, t
GND
pHZ pZH
L
Figure 1
AC Waveform
t 2.0 ns
f
t 2.0 ns
r
V
IH
90%
M
Input
( LEAB , LEBA )
V
V
M
V
M
M
10%
GND
t 2.0 ns
t 2.0 ns
f
r
t
w
(L)
V
IH
90%
Input
(An, Bn)
V
V
M
10%
GND
t (H)
s
t
h
(H)
t (L)
s
t (L)
h
V
OH
OL
Output
V
V
M
M
(Bn, An)
V
t
t
t
t
pLH
pLH
pHL
pHL
Figure 2 t
, t
, t , t , t
pLH pHL w s h
t 2.0 ns
r
t 2.0 ns
f
V
IH
90%
Input
( CEAB , CEBA )
V
V
M
V
M
M
10%
t 2.0 ns
GND
t 2.0 ns
f
r
t
w
(L)
V
IH
90%
Input
(An, Bn)
V
V
M
M
10%
GND
t (H)
s
t
h
(H)
t (L)
s
t (L)
h
Figure 3 t , t , t
h
w
s
12
2014-03-01
TC74VCXH16543FT
t 2.0 ns
r
t 2.0 ns
f
Output Enable Control
( OEAB , OEBA ,
CEAB , CEBA )
V
IH
90%
V
M
10%
GND
t
t
pLZ
t
pZL
3.0 V or V
CC
Output (An, Bn)
Low to Off to Low
V
M
V
V
X
V
V
OL
t
pHZ
pZH
OH
Y
Output (An, Bn)
High to Off to High
V
M
GND
Outputs
enabled
Outputs
disabled
Outputs
enabled
Figure 4 t
, t
, t
, t
pLZ pHZ pZL pZH
V
CC
Symbol
3.3 ± 0.3 V
2.7 V
2.5 ± 0.2 V
1.8 V
V
IH
V
CC
V
CC
V
M
1.5 V
V /2
CC
V /2
CC
V
V
V
+ 0.3 V
− 0.3 V
V
+ 0.15 V
− 0.15 V
V
+ 0.15 V
− 0.15 V
X
OL
OL
OL
V
OH
V
OH
V
OH
Y
13
2014-03-01
TC74VCXH16543FT
Package Dimensions
Weight: 0.25 g (typ.)
14
2014-03-01
TC74VCXH16543FT
RESTRICTIONS ON PRODUCT USE
•
•
•
Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
•
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
•
•
Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
•
•
The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
•
•
Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited
except in compliance with all applicable export laws and regulations.
Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
15
2014-03-01
相关型号：
©2020 ICPDF网 联系我们和版权申明